Beam shaping for microwave waveguide hyperthermia applicators

Clinical Feasibility of a High-Resolution Thermal Monitoring Sheet for Superficial Hyperthermia in Breast Cancer Patients

Simple Summary

Hyperthermia, i.e., heating tumors to 41–43 °C, combined with radiotherapy improves treatment response, for patients with recurrent breast cancer after previous irradiation. During hyperthermia of superficial tumors, the skin surface temperature must be monitored to ensure that therapeutic temperatures are reached without hotspots that can cause additional toxicity. A thin sheet with a dense grid of 56 temperature sensors was developed, this sheet is placed on the skin of the patient. The influence of the sheet on the hyperthermia applicator performance was investigated and found to be negligible. Next, the clinical feasibility was evaluated in 10 women with locoregional recurrent breast cancer, and resulted in precise monitoring of skin surface temperatures. In conclusion, this novel method can be implemented for thermal monitoring of the skin surface to ensure treatment quality during superficial hyperthermia treatment of patients with locoregional recurrent breast cancer.

Abstract

Background: Accurate monitoring of skin surface temperatures is necessary to ensure treatment quality during superficial hyperthermia. A high-resolution thermal monitoring sheet (TMS) was developed to monitor the skin surface temperature distribution. The influence of the TMS on applicator performance was investigated, feasibility and ability to reliably monitor the temperature distribution were evaluated in a clinical study. Methods: Phantom experiments were performed to determine the influence of the TMS on power deposition patterns, applicator efficiency, and heat transfer of the water bolus for 434 and 915 MHz applicators. Clinical feasibility was evaluated in 10 women with locoregional recurrent breast cancer. Skin surface temperatures during consecutive treatments were monitored alternatingly with either standard Amsterdam UMC thermometry or TMS. Treatments were compared using (generalized) linear mixed models. Results: The TMS did not significantly affect power deposition patterns and applicator efficiency (1–2%), the reduced heat transfer of the water boluses (51–56%) could be compensated by adjusting the water bolus flow. Skin surface temperatures were monitored reliably, and no alteration of thermal toxicity was observed compared to standard Amsterdam UMC thermometry. Conclusion: Clinical application of the TMS is feasible. Power deposition patterns and applicator efficiency were not affected. Surface temperatures were monitored reliably.

Two high-resolution thermal monitoring sheets for clinical superficial hyperthermia

PURPOSE

Temperature measurement during superficial hyperthermia is limited by poor spatial resolution. We investigated two sheets to improve temperature monitoring of the skin surface.

METHODS AND MATERIALS

Two different sheets were studied with a grid of temperature sensors with one sensor per ~5 cm2. The first was a matrix of multisensor thermocouple probes laced through a silicone sheet. The second sheet had rows of thermistors connected by meandering copper leads mounted on stretchable printed circuit board (SPCB). Accuracy, temperature resolution and two hour stability of both sheets were investigated. Furthermore, we determined the ability to follow body contours, thermal conduction errors and electromagnetic (EM) compatibility to clinically used 434 and 915 MHz hyperthermia applicators.

RESULTS

For both sheets the accuracy (≤0.2 °C), temperature resolution (≤0.03 °C) and stability (≤0.01°C hr-1) were adequate for clinical use. Thermal conduction errors ranged from 5.25 - 11.25 mm vs. 2.15 mm for the thermocouple probe and thermistor, respectively. Both sheets could follow body contours, where the ratio air/ water bolus surface was <5%. When aligned perpendicularly to the EM field the meandering copper tracks used on the SPCB did induce self-heating, while the thermocouple probes did not. Self-heating had a linear relationship with the angle of the leads with respect to the EM field direction for both sensors at both frequencies. Self-heating of the thermistor was similar for both frequencies, while it was circa two-fold higher for 915 vs. 434 MHz for the thermocouple.

CONCLUSION

The use of SPCB technology for skin surface monitoring was promising. However, suppressing self-heating induced by the horseshoe shaped copper tracks needed for stretchability of the SPCB requires more in-depth investigation. The thermocouple matrix was the most promising for clinical application, meeting 6/7 of the major requirements for skin surface temperature monitoring when positioned perpendicular to the EM field.

Microwave hyperthermia promotes caspase‑3-dependent apoptosis and induces G2/M checkpoint arrest via the ATM pathway in non‑small cell lung cancer cells

Post-operative microwave (MW) hyperthermia has been applied as an important adjuvant therapy to enhance the efficacy of traditional cancer treatment. A better understanding of the molecular mechanisms of MW hyperthermia may provide guided and further information on clinical hyperthermia treatment. In this study, we examined the effects of MW hyperthermia on non-small cell lung carcinoma (NSCLC) cells in vitro, as well as the underlying mechanisms. In order to mimic clinical treatment, we developed special MW heating equipment for this study. Various NSCLC cells (H460, PC-9 and H1975) were exposed to hyperthermia treatment using a water bath or MW heating system. The results revealed that MW hyperthermia significantly inhibited cell growth compared with the water bath heating system. Furthermore, MW hyperthermia increased the production of reactive oxygen species (ROS), decreased the levels of mitochondrial membrane potential (MMP) and induced caspase-3 dependent apoptosis. It also induced G₂/M phase arrest through the upregulation of the expression of phosphorylated (p-) ataxia telangiectasia mutated (ATM), p-checkpoint kinase 2 (Chk2) and p21, and the downregulation of the expression of cdc25c, cyclin B1 and cdc2. On the whole, the findings of this study indicate that the exposure of NSCLC cells to MW hyper-thermia promotes caspase-3 dependent apoptosis and induces G₂/M cell cycle arrest via the ATM pathway. This preclinical study may help to provide laboratory-based evidence for MW hyperthermia treatment in clinical practice.

Design of a compact antenna with flared groundplane for a wearable breast hyperthermia system

PURPOSE

Currently available microwave hyperthermia systems for breast cancer treatment do not conform to the intact breast and provide limited control of heating patterns, thereby hindering an effective treatment. A compact patch antenna with a flared groundplane that may be integrated within a wearable hyperthermia system for the treatment of the intact breast disease is proposed.

MATERIALS AND METHODS

A 3D simulation-based approach was employed to optimise the antenna design with the objective of maximising the hyperthermia treatment volume (41 °C iso-therm) while maintaining good impedance matching. The optimised antenna design was fabricated and experimentally evaluated with ex vivo tissue measurements.

RESULTS

The optimised compact antenna yielded a -10 dB bandwidth of 90 MHz centred at 915 MHz, and was capable of creating hyperthermia treatment volumes up to 14.4 cm(3) (31 mm × 28 mm × 32 mm) with an input power of 15 W. Experimentally measured reflection coefficient and transient temperature profiles were in good agreement with simulated profiles. Variations of + 50% in blood perfusion yielded variations in the treatment volume up to 11.5%. When compared to an antenna with a similar patch element employing a conventional rectangular groundplane, the antenna with flared groundplane afforded 22.3% reduction in required power levels to reach the same temperature, and yielded 2.4 times larger treatment volumes.

CONCLUSION

The proposed patch antenna with a flared groundplane may be integrated within a wearable applicator for hyperthermia treatment of intact breast targets and has the potential to improve efficiency, increase patient comfort, and ultimately clinical outcomes.

Enhancing the properties of beam forming bolus in hyperthermia: numerical simulation and empirical verification

In this paper we present a simulation study of the induced specific absorption rate (SAR) within the phantom produced by radiofrequency radiation from a 8 MHz capacitive applicator. The main focus of the current study is on demonstrating the beam shaping properties of the bolus system as well as its effect on controlling the therapeutic area. Different electrical conductivities and geometries of the bolus were considered in the simulation of induced SAR distributions in a muscle-equivalent model with uniform dielectric properties. To validate the presented model, we carried out a comparison between the SAR simulation results and the temperature measurements in an agar split-phantom and an excellent agreement was observed.

Hyperthermia, radiation and chemotherapy: the role of heat in multidisciplinary cancer care

The compelling biologic basis for combining hyperthermia with modern cancer therapies including radiation and chemotherapy was first appreciated nearly half a century ago. Hyperthermia complements radiation as conditions contributing to radio-resistance generally enhance sensitivity to heat and sensitizing effects occur through increased perfusion/tumor oxygenation and alteration of cellular death pathways. Chemosensitization with hyperthermia is dependent on the particular mechanism of effect for each agent with synergistic effects noted for several commonly used agents. Clinically, randomized trials have demonstrated benefit including survival with the addition of hyperthermia to radiation or chemotherapy in treatment of a wide range of malignancies. Improvements in treatment delivery techniques, streamlined logistics, and greater understanding of the relationship of thermal dosimetry to treatment outcomes continue to facilitate wider clinical implementation. Evolving applications include thermal enhancement of immunotherapy, targeted drug delivery and application of principals of thermal biology towards integration of thermal ablation into multimodality oncologic care.

Design of a water coupling bolus with improved flow distribution for multi-element superficial hyperthermia applicators

A water bolus used in superficial hyperthermia couples the electromagnetic (EM) or acoustic energy into the target tissue and cools the tissue surface to minimise thermal hotspots and patient discomfort during treatment. Parametric analyses of the fluid pressure inside the bolus computed using 3D fluid dynamics simulations are used in this study to determine a bolus design with improved flow and surface temperature distributions for large area superficial heat applicators. The simulation results are used in the design and fabrication of a 19 x 32 cm prototype bolus with dual input-dual output (DIDO) flow channels. Sequential thermal images of the bolus surface temperature recorded for a step change in the circulating water temperature are used to assess steady state flow and surface temperature distributions across the bolus. Modelling and measurement data indicate substantial improvement in bolus flow and surface temperature distributions when changing from the previous single input-single output (SISO) to DIDO configuration. Temperature variation across the bolus at steady state was measured to be less than 0.8 degrees C for the DIDO bolus compared to 1.5 degrees C for the SISO water bolus. The new DIDO bolus configuration maintains a nearly uniform flow distribution and low variation in surface temperature over a large area typically treated in superficial hyperthermia.

Multilayer conformal applicator for microwave heating and brachytherapy treatment of superficial tissue disease

PURPOSE

The purpose of this study was to construct and perform preliminary functionality evaluations of a multilayer conformal applicator with provisions for thermal monitoring, tight conformity and simultaneous microwave heating and brachytherapy treatment of large-area contoured surfaces.

MATERIALS AND METHODS

The multilayer conformal applicator consists of thermal monitoring catheters for fibre-optic monitoring of skin temperatures, a waterbolus, a PCB microwave antenna array, a dielectric spacer for brachytherapy considerations, brachytherapy catheters for delivering HDR radiation and an inflatable air bladder for improving conformity to contoured surfaces. The applicator also includes an elastic attachment structure to hold the applicator securely in place on the patient. The conformity of the applicator to irregular surfaces was evaluated through CT imaging of the applicator fitted onto a life-sized human torso phantom. The fluid flow dynamics of the waterbolus, which impact the effectiveness of temperature control, were evaluated with thermometry during a 19 degrees C step change temperature of the circulating water.

RESULTS

CT imaging showed improved conformity to the torso phantom surface following the application of gentle inward pressure from inflating the outer air bladder. Only a small number of 1-5 mm sized air gaps separated the conformal applicator and tissue surface. Thermometry testing of the bolus fluid flow dynamics demonstrated temperature uniformity within +/-0.82 degrees C across a 19 x 34 x 0.6 cm area bolus and +/-0.85 degrees C across a large 42 x 32 x 0.6 cm area bolus.

CONCLUSION

CT scans of the applicator confirmed that the applicator conforms well to complex body contours and should maintain good conformity and positional stability even when worn on a mobile patient. Thermometry testing of two different waterbolus geometries demonstrated that uniform circulation and temperature control can be maintained throughout large, complex bolus shapes.

Evolving technology for thermal therapy of cancer

This paper is intended as a succinct review of technology used for clinical hyperthermia therapy for cancer, as culled from a presentation at the special workshop on Thermal Medicine, Heat Shock Proteins, and Cancer at the Society for Thermal Medicine conference in Spring 2005. Following a brief overview of thermal therapy treatment options and available mechanisms for heating tissue, the paper focuses on the evolution of equipment from basic single element heating devices of the early 1980s to adjustable multi-element heating devices currently in use or in final stages of development. Representative devices from the past, present and near future are cited for further investigation by the interested reader. The paper concludes with a summary of general trends in the evolution of clinical hyperthermia techniques and a statement of current challenges remaining for the field.

Infrared thermographic SAR measurements of interstitial hyperthermia applicators: errors due to thermal conduction and convection

Thermal conduction and convection were examined as sources of error in thermographically measured SAR patterns of an interstitial microwave hyperthermia applicator. Measurements were performed in a layered block of muscle-equivalent phantom material using an infrared thermographic technique with varying heating duration. There was a 52.7% reduction in maximum SAR and 75.5% increase in 50% iso-SAR contour area for a 60-s heating duration relative to a 10-s heating duration. A finite element model of heat transfer in an homogeneous medium was used to model conductive and convective heat transfer during the thermographic measurement. Thermal conduction artefacts were found to significantly distort thermographically measured SAR patterns. Convective cooling, which occurs when phantom layers are exposed for thermal image acquisition, was found to significantly affect the magnitude, but not the spatial distribution, of thermographically measured SAR patterns. Results from this investigation suggest that the thermal diffusion artefacts can be minimized if the duration of the applied power pulse is restricted to 10 s or less.

Feasibility of salvage interstitial microwave thermal therapy for prostate carcinoma following failed brachytherapy: studies in a tissue equivalent phantom

Thermal therapy is an experimental treatment to destroy solid tumours by heating them to temperatures ranging from 55 degrees C to 90 degrees C, inducing thermal coagulation and necrosis of the tumour. We are investigating the feasibility of interstitial microwave thermal therapy as a salvage treatment for prostate cancer patients with local recurrence following failed brachytherapy. Due to the electrical and thermal conductivity of the brachytherapy seeds, we hypothesized that the seeds could scatter the microwave energy and cause unpredictable heating. To investigate this, a 915 MHz helical antenna was inserted into a muscle-equivalent phantom with and without brachytherapy seeds. Following a 10 W, 5 s input to the antenna, the temperature rise was used to calculate absorbed power, also referred to as specific absorption rate (SAR). Plane wave models based on Maxwell's equations were also used to characterize the electromagnetic scattering effect of the seeds. In addition, the phantom was heated with 8 W for 5 min to quantify the effect of the seeds on the temperature distribution during extended heating. SAR measurements indicated that the seeds had no significant effect on the shape and size of the SAR pattern of the antenna. However, the plane wave simulations indicated that the seeds could scatter the microwave energy resulting in hot spots at the seed edges. Lack of experimental evidence of these hot spots was probably due to the complex polarization of the microwaves emitted by the helical antenna. Extended heating experiments also demonstrated that the seeds had no significant effect on the temperature distributions and rates of temperature rise measured in the phantom. The results indicate that brachytherapy seeds are not a technical impediment to interstitial microwave thermal therapy as a salvage treatment following failed brachytherapy.

Optimization of a beam shaping bolus for superficial microwave hyperthermia waveguide applicators using a finite element method

Temperature inhomogeneity in hyperthermia treatments often limits the total thermal dose that can be delivered to the tumour region. To reduce such inhomogeneities, a prototype dynamically modifiable square array of saline-filled patches which attenuate microwave energy was developed for superficial treatments that use external microwave applicators. The array was situated inside the coupling water bolus that is often used with external applicators. The prototype has been previously tested clinically with promising results. A more complete theoretical analysis of the performance of this new bolus design and improvements to its design by modelling are presented here. The analysis was performed by performing five iterative simulations of the SAR pattern produced inside a tissue structure by a waveguide applicator with a water bolus containing the dynamic patch array attached. Between iterations the patch array configuration was modified in an attempt to improve the ability of the bolus to confine heating to an 'L'-shaped tumour region. These simulations were performed using the finite element method. The steady-state temperature profile was then computed using a finite element method based simulation of heat transfer that assumed a given applicator power level and water bolus temperature. Several iterations of these heat transfer simulations were performed with varying applicator power level and water bolus temperature to improve the confinement of heating to the target region. The analysis showed that the dynamic patch array should be capable of conforming heating to an 'L'-shaped target tumour region while limiting the heating to the surrounding normal tissue to an acceptable level.

Helical antenna arrays for interstitial microwave thermal therapy for prostate cancer: tissue phantom testing and simulations for treatment

Interstitial microwave therapy is an experimental treatment for prostate cancer. The objective of this work was to measure the power deposition (specific absorption rate, SAR) patterns of helical microwave antennae both individually and in array patterns that would be useful for clinical treatment protocols. Commercial helical antenna 3D SAR patterns were measured in muscle equivalent phantoms using a thermographic technique. Two array patterns were tested: a 'square' and a 'crescent' array, both surrounding the urethra. To assess the feasibility of pre-treatment planning, the measured SAR patterns were input to a treatment planning computer simulation program based on a series of trans-rectal ultrasound images from a prostate cancer patient. The simulation solved the Pennes linear bioheat heat transfer equation in prostate tissue, with the aim of achieving a target of 55 degrees C at the prostate periphery while not allowing normal surrounding tissues (bladder, urethra, rectum) to rise above 42 C. These criteria could not be met with the square array but they could be met with the crescent array, provided that the prostate was first dissected away from the rectum. This can be done with a procedure such as 'hydrodissection', where sterile saline is injected to separate the prostate and rectum. The results of these SAR measurements and heat transfer simulations indicate that arrays of helical antennae could be used for safe and effective thermal therapy for prostate cancer.

Research and development of hyperthermia machines for present and future clinical needs

This article describes the clinical problems encountered with the use of hyperthermia equipment and the requisites in the development of more advanced systems. A summary of the trends in the development of hyperthermia equipment is presented. In addition, a description from the physical point of view is included for the design of new applicators for deep heating.

A 433 MHz Lucite cone waveguide applicator for superficial hyperthermia

The effective field size (EFS, SAR > or = 50% of the maximum SAR at 1 cm depth) of a conventional 433 MHz water filled waveguide applicator (32 cm2, aperture area 100 cm2) has been increased by: (1) replacement of the two diverging brass side walls which are parallel to the direction of the electric field by Lucite walls; and (2) Placement of a heterogeneous permittivity in the centre of the aperture. SAR distributions were measured at several depths in layered fat-muscle phantoms. With Lucite side walls the SAR distribution becomes wider in the H-plane of the aperture, resulting in a circular SAR distribution. In this situation the EFS is 67 cm2. Additional insertion of a PVC cone with a top angle of 15 degrees at the centre of the aperture increases the EFS to 91 +/- 6 cm2 for a waterbolus of 18 x 18 x 1 cm3. The experiments also demonstrated that the resulting EFS is affected by the waterbolus size and shape. Calorimetric measurements showed that the efficiency of the improved applicator is comparable to the efficiency of the conventional water filled waveguide applicator, 50 and 56% respectively. The modifications reported provide a simple and inexpensive means to increase the EFS and can be easily implemented in water filled waveguide applicators.

Clinical system for simultaneous external superficial microwave hyperthermia and cobalt-60 radiation

A system for simultaneous thermoradiotherapy was devised to investigate the possible benefits and/or complications of thermal radiosensitization in human superficial tumours. The system combines the well-known treatment modalities of external 915 MHz microwave hyperthermia and cobalt-60 teletherapy. Single waveguide applicators are utilized either attached to blocking trays, so that the gamma beam travels through a waveguide and into the patient (en face setup), or in a conventional way with the microwave propagation vector orthogonal to the gamma beam (orthogonal setup). With these setups a radiation fraction can be delivered in the middle of a 60-min, non-interrupted hyperthermia treatment. Temperatures and power level are remotely monitored and recorded outside the Cobalt room. Extensive measurements and testing showed that the operation of the hyperthermia system (generator, applicators, thermometry unit and temperature sensors) was not disrupted by irradiation and that the microwaves were confined to the treatment room and did not interfere with the operation of the Cobalt unit, of an adjacent linear accelerator or of an adjacent radiotherapy simulator. For the en face setup the dose distributions induced in solid water phantoms were uniform with the exception of a narrow (< 0.5 cm) region under the applicators' internal probes where 10-18% reduction exists. This dose defect is clinically smoothed using feathering techniques. The system has been successfully used without technical problems in 51 treatments in 15 patients (18 lesions) in a phase I/II clinical trial. An analysis of the thermal data showed that the temperature distributions achieved during simultaneous delivery have the same general characteristics of those achieved in conventional sequential hyperthermia with microwaves, and that the steady state distributions are maintained during the time of simultaneous irradiation. The tests performed in addition to the preliminary clinical experience clearly indicate that this type of combined therapy is technically feasible and safe. Here the system for simultaneous, external, superficial thermoradiotherapy and the implementation tests performed are described in detail. Preliminary clinical experience and results are also reported.

A variable microwave array attenuator for use with single-element waveguide applicators

The effectiveness of hyperthermia treatments is often limited by temperature inhomogeneity that arises in the treatment field due to variable tissue properties and blood flow. Moreover, blood flow can change during a treatment, leading to the formation of hot and cool areas even if the initial temperature distribution is uniform. A variable microwave array attenuator has been constructed, that will enable the field patterns of single element microwave waveguide hyperthermia applicators to be altered during treatment, to improve temperature homogeneity. The coupling bolus was designed with an array of individually controlled elements, each filled with a microwave absorbing saline solution. Additions or withdrawals of saline are made to alter the power deposition in a specific area of the treatment field. Thermographic measurements were made in muscle equivalent phantom materials, with the bolus/waveguide assembly. Results showed that the variable array attenuator was able to significantly alter the heating pattern of a large waveguide applicator.

Effect of vascular occlusion on tumour temperatures during superficial hyperthermia

Tumour temperature heterogeneity during hyperthermia has been attributed to irregular tumour vascular perfusion. We have compared temperature distributions in human tumours subjected to superficial hyperthermia under conditions of normal and occluded blood flow. Three patients with recurrent malignant melanoma on the leg were treated with radiation followed by hyperthermia 60-90 min later on days 1, 8 and 22. Heating (15-30 min) with normal blood flow was followed by 15 min of heating with tourniquet occlusion, although the tourniquet had to be intermittently released when the patients complained of discomfort. Hyperthermia was delivered using either a 1.4 MHz ultrasound or 915 MHz microwave applicator. Temperatures were monitored using superficial and interstitial thermometers in tumour and normal tissues. When the tourniquet was applied, the amount of power required to maintain peak temperatures was decreased by a factor of 3-10. With normal blood flow, there was a significant degree of temperature heterogeneity within the treatment volume, both within normal and tumour tissues, which improved with tourniquet application. The T90 and T50 indices increased both in normal tissues and tumour following the tourniquet occlusion, with the temperature increments being greater for normal tissues. Temperatures at depth were increased despite the reduction in applied power and the temperature profiles were smoother when the tourniquet was applied. No cutaneous, vascular or neuromuscular side effects were observed amongst these three subjects either acutely or at 1 month follow-up. These studies demonstrate directly that the temperature heterogeneity which exists in human tumours subjected to external heating can be reduced by occluding the blood supply.