Compression and tableting of pharmaceutical powders at elevated temperatures

Understanding the roles of compaction pressure and crystal hardness on powder tabletability through bonding area - Bonding strength interplay

Bonding area (BA) and bonding strength (BS) interplay dictates tensile strength of a tablet and, hence, tabletability. Using a series of alkali halides with mechanical properties spanning more than one order of magnitude, the role of compaction pressure and mechanical properties on tabletability is systematically investigated and explained using the BA-BS interplay. Results reveal that BA dominates the BA-BS interplay at low pressures, where more plastic powders attain higher tensile strength due to larger BA. In contrast, BS dominates the interplay at high pressures, when difference in BA between powders is minimized. Under the typical compaction pressures of 100-300 MPa, tablet tensile strength is the highest for materials with intermediate hardness, or plasticity, due to an optimal BA-BS interplay.

Effect of tableting temperature on tablet properties and dissolution behavior of heat sensitive formulations

The tableting process involves the conversion of mechanical to thermal energy. This study evaluated the influence of temperature on the tableting behavior of formulations with different compositions. The tableting machine was equipped with a thermally controlled die to mimic the heat evolution from tableting on an industrial scale. Six formulations containing binders with a comparably low glass transition temperature were examined. Besides the polymer type and concentration, the filler was varied. Paracetamol was chosen as the model active pharmaceutical ingredient. The investigation included alterations in tabletability, disintegration and dissolution. Elevated temperatures led to an enhanced tabletability. The polymer type and concentration were decisive for the extent of alterations. The variation of the filler composition played a minor role due to the high melting points of its components. The results were confirmed in disintegration and dissolution studies. A high binding capacity and a low glass transition temperature resulted in a stronger delay of disintegration. The dissolution was sustained. Increased concentrations of the binding polymer enhanced the effect. If the tableting behavior of a formulation is changed by elevated temperatures during formulation development and production, a change of the binder type or concentration should be considered to ensure a reproducible tablet quality.

Evaluation of In-Die Compression Data for a Deeper Understanding of Altered Excipient Properties upon Temperature Rise

The thermodynamic analysis of tablet formation includes the thermal and mechanical analysis during compression. The aim of this study was to evaluate alterations of force-displacement data upon temperature rise as an indicator for changed excipient properties. The tablet press was equipped with a thermally controlled die to imitate the heat evolution from tableting on an industrial scale. Six predominantly ductile polymers with a comparably low glass transition temperature were tableted at temperatures ranging from 22-70°C. Lactose served as a brittle reference with a high melting point. The energy analysis included the net and recovery work during compression, from which the plasticity factor was calculated. The respective results were compared to the changes in compressibility obtained via Heckel analysis. Elevated temperatures reduced the necessary work for plastic deformation for the ductile polymers, which was reflected in decreasing values for the net work of compaction and the plasticity factor. The recovery work slightly increased for the maximum tableting temperature. Lactose showed no response to temperature variations. Changes in the net work of compaction showed a linear correlation to the changes in yield pressure, which could be correlated to the glass transition temperature of a material. It is therefore possible to detect material alterations directly from the compression data, if the glass transition temperature of a material is sufficiently low.

Interaction and Compatibility Studies in the Development of Olmesartan Medoxomil and Hydrochlorothiazide Formulations under a Real Manufacturing Process

A drug–drug and drug–excipient interactions and compatibilities study was conducted for two fixed-dose combination (FDC) products containing olmesartan medoxomil (OLM)/hydrochlorothiazide (HCT) 20/12.5 mg and OLM/HCT 40/12.5 mg during their development including storage. The study consisted of the evaluation of samples retrieved during all stages of a real manufacturing process. Powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC), thermogravimetry (TGA), Fourier transform infrared spectroscopy (FT-IR), and contact angle techniques were applied to the samples to determine interactions and incompatibilities. Dissolution tests and long-term stability studies were conducted to evaluate dosage form performance. Results showed weak solid–state interactions able to obtain a eutectic mixture of OLM and HCT while microcrystalline cellulose (MC) impacted the thermal stability of both drugs. Reliable dissolution and long-term stability tests confirmed that the interactions observed were not considered incompatibilities because they were not influenced by the performance of the final products.

Natural binders and solid bridge type binding mechanisms in briquettes and pellets made from corn stover and switchgrass

Corn stover and switchgrass are two important feedstocks considered for producing renewable fuels and energy in the US. Densification of these biomass feedstocks into briquettes/pellets would help reduce the problems and costs of bulk transportation, handling, and storage of biomass feedstocks. In this study, the role of the natural binders in corn stover and switchgrass to make durable particle-particle bonding in briquettes/pellets was investigated by micro-structural analyses. Scanning Electron Microscopy (SEM) images of briquettes made by using a uniaxial piston-cylinder densification apparatus in the laboratory, briquettes made by using a pilot-scale roll-press briquetting machine, and pellets made by using a pilot-scale conventional ring-die pelleting machine were analysed. The SEM images showed that the bonding between particles was created mainly through solid bridges. The solid bridges between particles were made by natural binders in the biomass expressed during the densification process. UV auto-fluorescence images of briquettes and pellets further confirmed that the solid bridges were made mainly by natural binders such as lignin and protein. It was found that activating (softening) the natural binders using moisture and temperature in the range of glass transition is important to make durable particle-particle bonding.