Competitive displacement of proteins in oil-in-water emulsions containing calcium ions

Interfacial protein-protein displacement at fluid interfaces

Protein blends are used to stabilise many traditional and emerging emulsion products, resulting in complex, non-equilibrated interfacial structures. The interface composition just after emulsification is dependent on the competitive adsorption between proteins. Over time, non-adsorbed proteins are capable of displacing the initially adsorbed ones. Such rearrangements are important to consider, since the integrity of the interfacial film could be compromised after partial displacement, which may result in the physical destabilisation of emulsions. In the present review, we critically describe various experimental techniques to assess the interfacial composition, properties and mechanisms of protein displacement. The type of information that can be obtained from the different techniques is described, from which we comment on their suitability for displacement studies. Comparative studies between model interfaces and emulsions allow for evaluating the impact of minor components and the different fluid dynamics during interface formation. We extensively discuss available mechanistic physical models that describe interfacial properties and the dynamics of complex mixed systems, with a focus on protein in-plane and bulk-interface interactions. The potential of Brownian dynamic simulations to describe the parameters that govern interfacial displacement is also addressed. This review thus provides ample information for characterising the interfacial properties over time in protein blend-stabilised emulsions, based on both experimental and modelling approaches.

A statherin and calcium enriched layer at the air interface of human parotid saliva

Parotid saliva placed in 35-mm-diameter tissue culture dishes developed increasing surface viscoelasticity at the interface with air. A surface layer became visible with time, and was collected and analysed by protein electrophoresis which indicated that a single protein (pI 4.2; molecular mass approx. 6 kDa) predominated. Western blot analysis demonstrated that the major protein band reacted with an antiserum directed against the C-terminal of the calcium-binding salivary protein statherin. Matrix-assisted laser-desorption ionization-time-of-flight MS analysis gave a molecular mass of 5380 Da for the protein, corresponding to the molecular mass of statherin. Staining of film protein in electrophoresis gels was compared with statherin synthesized on a solid phase, and the mean statherin content of film formed from 1 ml of parotid saliva was measured as 7 nmol. The mean calcium content of the surface layer was 250 nmol. Surface rheology was greatly decreased in the presence of EDTA, whereas surface tension of saliva was unaffected by calcium chelation, suggesting that protein accumulated at the surface was unaffected. The results suggest that a layer rich in statherin forms at the interface of saliva and air, and that the surface rheology developed is dependent upon protein interactions mediated by calcium. The surface layer may enhance the function of saliva as a protective layer on the mucosal surfaces and teeth.

Effect of pH and ionic strength on competitive protein adsorption to air/water interfaces in aqueous foams made with mixed milk proteins

Quantitative analysis of competitive milk protein adsorption to air/water interfaces in aqueous foam was performed by capillary electrophoresis (CE). Foams were made by whipping protein solutions, in which skim milk powder (SMP) and whey protein isolate (WPI) were mixed at 0.5% protein in different proportions at different pH values and NaCl concentrations. Preferential adsorption of beta-casein into foam phases occurred under most solution conditions, if partial dissociation of the casein micelles had occurred. Preferential adsorption of beta-casein was not observed with added Ca2+, due to the re-association of casein micelles. Enrichment of caseins into the foam phase was more apparent than that of whey proteins. The foamability of SMP demonstrated a continuous improvement due to the gradually increasing dissociation of casein micelles when the concentration of NaCl increased from 0 to 0.8 M. The foamability of WPI increased when NaCl concentration rose from 0 to 0.1 M, and decreased with further increase in NaCl concentration. NaCl at low concentration (I < or = 0.4) did not show a significant effect on the competitive adsorption among milk proteins, indicating that electrostatic interactions do not play a key role in competitive adsorption. NaCl at higher concentration, e.g., 0.6 M, caused less whey protein to be adsorbed to the air/water interfaces. The whippability of WPI was highest at pH 4.5 and lowest at pH 3, and that of SMP was the opposite. The proportions of beta-lactoglobulin and alpha-lactalbumin in the foam phase were lower at acidic pH and higher at basic pH, compared with that at natural pH of WPI.

Milk protein interfacial layers and the relationship to emulsion stability and rheology

The properties of milk protein-stabilised, oil-in-water emulsions are determined by the structure and surface rheology of the adsorbed layer at the oil-water interface. Analysis of the segment density profiles normal to the surface show differences in the structure between adsorbed layers of disordered casein and globular whey protein. Systematic studies of stability and rheology of model oil-in-water emulsion systems made with milk proteins as sole emulsifiers give insight into the relation between adsorbed layer properties and bulk emulsion stability. Of particular importance are effects of pH, temperature, calcium ions and protein content. Colloidal interactions between adsorbed layers on different surfaces can be inferred from an analysis of dynamic collisions of protein-coated emulsion droplets in shear flow using the colloidal particle scattering technique. The role of competitive adsorption on emulsion properties can be derived from experiments on systems containing mixtures of milk proteins and small-molecule surfactants. Shear-induced destabilisation is especially influenced by the presence of fat crystals in the emulsion droplets. Aggregated gel network properties are dependent on the balance of weak and strong interparticle interactions. In heat-set whey protein emulsion gels, the rheological behaviour is especially sensitive to surfactant type and concentration. Rearrangements of transient caseinate-based emulsion gels can have a profound influence on the quiesent stability behaviour. Computer simulation provides a general link between particle interactions, microstructure and rheological properties.