Comparative modeling and analysis of microfluidic and conventional DNA microarrays

Reversible bonding of microfluidics: Review and applications

With the development of microfluidic technology, new materials and fabrication methods have been constantly invented in the field of microfluidics. Bonding is one of the key steps for the fabrication of enclosed-channel microfluidic chips, which have been extensively explored by researchers globally. The main purpose of bonding is to seal/enclose fabricated microchannels for subsequent fluid manipulations. Conventional bonding methods are usually irreversible, and the forced detachment of the substrate and cover plate may lead to structural damage to the chip. Some of the current microfluidic applications require reversible bonding to reuse the chip or retrieve the contents inside the chip. Therefore, it is essential to develop reversible bonding methods to meet the requirements of various applications. This review introduces the most recent developments in reversible bonding methods in microfluidics and their corresponding applications. Finally, the perspective and outlook of reversible bonding technology were discussed in this review.

Centrifugal microfluidic lab-on-a-chip system with automated sample lysis, DNA amplification and microarray hybridization for identification of enterohemorrhagic Escherichia coli culture isolates

Automated workflow that starts with a colony isolate and ends with a fluorescence signal on a DNA microarray.

Effect of buffer composition on PNA–RNA hybridization studied in the microfluidic microarray chip

Herein, we report that peptide nucleic acid sequences (PNAs) have been used as the probe species for detection of RNA and that a microfluidic microarray (MMA) chip is used as the platform for detection of hybridizations between immobilized PNA probes and RNA targets. The RNA targets used are derived from influenza A sequences. This paper discusses the optimization of two probe technologies used for RNA detection and investigates how the composition of the probe buffer and the content of the hybridization solution can influence the overall results. Our data show that the PNA probe is a better choice than the DNA probe when there is low salt in the probe buffer composition. Furthermore, we show that the absence of salt (NaCl) in the hybridization buffer does not hinder the detection of RNA sequences. The results provide evidence that PNA probes are superior to DNA probes in term of sensitivity and adaptability, as PNA immobilization and PNA–RNA hybridization are less affected by salt content in the reaction buffers unlike DNA probes.

Focused Glycomic Profiling With an Integrated Microfluidic Lectin Barcode System

Protein glycosylation is one of the key processes that play essential roles in biological functions and dysfunctions. However, progress in glycomics has considerably lagged behind genomics and proteomics, due in part to the enormous challenges associated with the analysis of glycans. Here we present a new integrated and automated microfluidic lectin barcode platform to substantially improve the performance of lectin array for focused glycomic profiling. The chip design and flow control were optimized to promote the lectin-glycan binding kinetics and the speed of lectin microarrays. Moreover, we established an on-chip lectin assay which employs a very simple blocking method to effectively suppress the undesired background due to lectin binding of antibodies. Using this technology, we demonstrated focused differential profiling of tissue-specific glycosylation changes of a biomarker, the CA125 protein purified from ovarian cancer cell lines, and different tissues from ovarian cancer patients in a fast, reproducible, and high-throughput fashion. Highly sensitive CA125 detection was also demonstrated with a detection limit much lower than the clinical cutoff value for cancer diagnosis. This microfluidic platform holds the potential to integrate with sample preparation functions to construct a fully integrated "sample-to-answer" microsystem for focused differential glycomic analysis. Thus, our technology should present a powerful tool in support of rapid advance in glycobiology and glycobiomarker development.

Integrated Microfluidic Lectin Barcode Platform for High-Performance Focused Glycomic Profiling

Protein glycosylation is one of the key processes that play essential roles in biological functions and dysfunctions. However, progress in glycomics has considerably lagged behind genomics and proteomics, due in part to the enormous challenges in analysis of glycans. Here we present a new integrated and automated microfluidic lectin barcode platform to substantially improve the performance of lectin array for focused glycomic profiling. The chip design and flow control were optimized to promote the lectin-glycan binding kinetics and speed of lectin microarray. Moreover, we established an on-chip lectin assay which employs a very simple blocking method to effectively suppress the undesired background due to lectin binding of antibodies. Using this technology, we demonstrated focused differential profiling of tissue-specific glycosylation changes of a biomarker, CA125 protein purified from ovarian cancer cell line and different tissues from ovarian cancer patients in a fast, reproducible, and high-throughput fashion. Highly sensitive CA125 detection was also demonstrated with a detection limit much lower than the clinical cutoff value for cancer diagnosis. This microfluidic platform holds the potential to integrate with sample preparation functions to construct a fully integrated "sample-to-answer" microsystem for focused differential glycomic analysis. Thus, our technology should present a powerful tool in support of rapid advance in glycobiology and glyco-biomarker development.

Mass transfer in the biomolecular binding of a target against probe molecules on the surface of microbeads sequestered in wells in a microfluidic cell

Diagnostic tools which screen the binding interactions of a protein target against a display of biomolecular probes to identify molecules which bind the target are central to cell proteomic studies, and to diagnostic assays. Here, we study a microfluidic design for screening interactions in which the probe molecules are hosted on microbeads sequestered in wells arranged at the bottom of a microfluidic flow channel. Assays are undertaken by streaming an analyte solution with a fluorescently labelled target through the cell, and identifying the fluorescing beads. Numerical simulations are first constructed for the analyte flow over the microbeads in the well array, and the increase in the target concentration on the microbead surface. The binding profile is expressed as a function of the ratio of the convective to the diffusive transport rates (Peclet number or Pe), and the ratio of the kinetic to the diffusive rates (Damkohler number, Da). For any Pe, as Da becomes small enough, the transport is determined by the intrinsic kinetic binding rate. As Pe increases, a thin concentration boundary layer develops over the top surface of the microbead because of the convective flow, and target binds more rapidly. However, the relatively stagnant layers of liquid in the well provide a diffusion barrier which slows the target transport, and for any Da and Pe the transport is slower than equivalent patches of probes arranged on the channel wall. Experiments are also undertaken at high Pe, using the binding of fluorescently labelled NeutrAvidin as a target to probes of its binding partner, biotin, on the microbead surface. The binding profile is compared to the simulations to measure the kinetic rate constant, and this comparison shows that the transport in the cell is not kinetically limited because of the diffusion barriers created by the stagnant liquid layer in the well. Simulations and experiments on microbeads which are only partially recessed in the well demonstrate an increase in the mass transfer rate as more of the microbead surface intersects the flow and the diffusion limitation due to the stagnant layer of liquid surrounding the bottom part of the microbead is minimized.

Oil-encapsulated nanodroplet array for bio-molecular detection

Detection of low abundance biomolecules is challenging for biosensors that rely on surface chemical reactions. For surface reaction based biosensors, it require to take hours or even days for biomolecules of diffusivities in the order of 10(-10-11) m2/s to reach the surface of the sensors by Brownian motion. In addition, often times the repelling Coulomb interactions between the molecules and the probes further defer the binding process, leading to undesirably long detection time for applications such as point-of-care in vitro diagnosis. In this work, we designed an oil encapsulated nanodroplet array microchip utilizing evaporation for pre-concentration of the targets to greatly shorten the reaction time and enhance the detection sensitivity. The evaporation process of the droplets is facilitated by the superhydrophilic surface and resulting nanodroplets are encapsulated by oil drops to form stable reaction chamber. Using this method, desirable droplet volumes, concentrations of target molecules, and reaction conditions (salt concentrations, reaction temperature, etc.) in favour of fast and sensitive detection are obtained. A linear response over 2 orders of magnitude in target concentration was achieved at 10 fM for protein targets and 100 fM for miRNA mimic oligonucleotides.

Dip-pen microarraying of molecular beacon probes on microgel thin-film substrates

Micron-sized spots of molecular beacon probes are patterned on PEG microgel thin films using dip-pen nanolithography.

3D thermoplastic elastomer microfluidic devices for biological probe immobilization

Microfluidics has emerged as a valuable tool for the high-resolution patterning of biological probes on solid supports. Yet, its widespread adoption as a universal biological immobilization tool is still limited by several technical challenges, particularly for the patterning of isolated spots using three-dimensional (3D) channel networks. A key limitation arises from the difficulties to adapt the techniques and materials typically used in prototyping to low-cost mass-production. In this paper, we present the fabrication of thin thermoplastic elastomer membranes with microscopic through-holes using a hot-embossing process that is compatible with high-throughput manufacturing. The membranes provide the basis for the fabrication of highly integrated 3D microfluidic devices with a footprint of only 1 × 1 cm(2). When placed on a solid support, the device allows for the immobilization of up to 96 different probes in the form of a 10 × 10 array comprising isolated spots of 50 × 50 μm(2). The design of the channel network is optimized using 3D simulations based on the Lattice-Boltzmann method to promote capillary action as the sole force distributing the liquid in the device. Finally, we demonstrate the patterning of DNA and protein arrays on hard thermoplastic substrates yielding spots of excellent definition that prove to be highly specific in subsequent hybridization experiments.

Fast DNA and protein microarray tests for the diagnosis of hepatitis C virus infection on a single platform

Hepatitis C virus (HCV) is a major cause of chronic liver disease and liver cancer, and remains a large health care burden to the world. In this study we developed a DNA microarray test to detect HCV RNA and a protein microarray to detect human anti-HCV antibodies on a single platform. A main focus of this study was to evaluate possibilities to reduce the assay time, as a short time-to-result (TTR) is a prerequisite for a point-of-care test. Significantly reducing hybridisation and washing times did not impair the assay performance. This was confirmed first using artificial targets and subsequently using clinical samples from an HCV seroconversion panel derived from a HCV-infected patient. We were able to reduce the time required for the detection of human anti-HCV antibodies to only 14 min, achieving nanomolar sensitivity. The protein microarray exhibited an analytical sensitivity comparable to that of commercial systems. Similar results were obtained with the DNA microarray using a universal probe which covered all different HCV genotypes. It was possible to reduce the assay time after PCR from 150 min to 16 min without any loss of sensitivity. Taken together, these results constitute a significant step forward in the design of rapid, microarray-based diagnostics for human infectious disease, and show that the protein microarray is currently the most favourable candidate to fill this role.

PDMS microfluidic capillary systems for patterning proteins on surfaces and performing miniaturized immunoassays

In this chapter, we describe the fabrication and use of microfluidic capillary systems (CSs) made in soft, transparent polydimethylsiloxane (PDMS). Sixteen microfluidic CSs, each containing a loading pad, a microchannel, and a capillary pump are engraved in a single PDMS chip. The CSs are used for two applications, firstly to pattern fibronectin on glass surfaces to locally control the adhesion of cultured cells to the substrate, and secondly to carry out multiplexed miniaturized immunoassays.

Microfluidic DNA microarray analysis: a review

Microarray DNA hybridization techniques have been used widely from basic to applied molecular biology research. Generally, in a DNA microarray, different probe DNA molecules are immobilized on a solid support in groups and form an array of microspots. Then, hybridization to the microarray can be performed by applying sample DNA solutions in either the bulk or the microfluidic manner. Because the immobilized probe DNA binds and retains its complementary target DNA, detection is achieved through the read-out of the tagged markers on the sample target molecules. The recent microfluidic hybridization method shows the advantages of less sample usage and reduced incubation time. Here, sample solutions are confined in microfabricated channels and flow through the probe microarray area. The high surface-to-volume ratio in microchannels of nanolitre volume greatly enhanced the sensitivity as obtained with the bulk solution method. To generate nanolitre flows, different techniques have been developed, and this including electrokinetic control, vacuum suction and syringe pumping. The latter two are pressure-driven methods which are more flexible without the need of considering the physicochemical properties of solutions. Recently, centrifugal force is employed to drive liquid movement in microchannels. This method utilizes the body force from the liquid itself and there are no additional solution interface contacts such as from electrodes or syringes and tubing. Centrifugal force driven flow also features the ease of parallel hybridizations. In this review, we will summarize the recent advances in microfluidic microarray hybridization and compare the applications of various flow methods.

Gold nanoparticle-assisted single base-pair mismatch discrimination on a microfluidic microarray device

Two simple gold nanoparticle (GNP)-based DNA analysis methods using a microfluidic device are presented. In the first method, probe DNA molecules are immobilized on the surface of a self-assembled submonolayer of GNPs. The hybridization efficiency of the target oligonulceotides was improved due to nanoscale spacing between probe molecules. In the second method, target DNA molecules, oligonulceotides or polymerase chain reaction (PCR) amplicons, are first bound to GNPs and then hybridized to the immobilized probe DNA on a glass slide. With the aid of GNPs, we have successfully discriminated, at room temperature, between two PCR amplicons (derived from closely related fungal pathogens, Botrytis cinerea and Botrytis squamosa) with one base-pair difference. DNA analysis on the microfluidic chip avoids the use of large sample volumes, and only a small amount of oligonucelotides (8 fmol) or PCR products (3 ng), was needed in the experiment. The whole procedure was accomplished at room temperature in 1 h, and apparatus for high temperature stringency was not required.

Optimization of a microfluidic microarray device for the fast discrimination of fungal pathogenic DNA

A microfluidic microarray device, which has been developed for parallel DNA detection, is now further optimized for more rapid and sensitive DNA detection and for the single-base-pair discrimination of two fungal pathogenic PCR products. Two poly(dimethylsiloxane) (PDMS)-based microfluidic chips consist of radial and spiral microchannels in which flexible probe creation and convenient sample delivery have been achieved by centrifugal pumping. The microarray hybridizations occurred at the cross sections within the spiral channels intersecting the preprinted radial probe lines. The centrifugal pumping method showed advantages over the vacuum suction method in terms of parallel solution delivery and less signal variations between replicate samples. The effect of microchannel depth was studied, and hybridization time is predictable at a certain rotation speed. Cy5 dye labels were proved to show much higher hybridization efficiency as well as less photobleaching effect as compared with the fluorescein dye labels used in our previous work. With these optimized conditions, the method was applied to the detection of three fungal pathogenic polymerase chain reaction (PCR) products with a sample load of 0.2 ng (in 1 microl). Furthermore, the single-base-pair discrimination between the PCR products of two relevant Botrytis species (B. cinerea and B. squamosa) was achieved in a duration as short as 3 min.

Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics

This paper details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute electrolytes consisting of a long serpentine microchannel lined with three dimensional (3D) stepped electrode arrays. Using low AC voltage (1 V rms, 1 kHz), power (5 mW) and current (4.5 mA) in water, the pump is capable of generating a 1.3 kPa head pressure, a 100-fold increase over prior ACEO pumps, and a 1.3 mm/s effective slip velocity over the electrodes without flow reversal. The integrated ACEO pump can utilize low ionic strength solutions such as distilled water as the working solution to pump physiological strength (100 mM) biological solutions in separate microfluidic devices, with potential applications in portable or implantable biomedical microfluidic devices. As a proof-of-concept experiment, the use of the ACEO pumps for DNA hybridization in a microfluidic microarray is demonstrated.

Microfluidic patterning of miniaturized DNA arrays on plastic substrates

This paper describes the patterning of DNA arrays on plastic surfaces using an elastomeric, two-dimensional microcapillary system (muCS). Fluidic structures were realized through hot-embossing lithography using Versaflex CL30. Like elastomers based on poly(dimethylsiloxane), this thermoplastic block copolymer is able to seal a surface in a reversible manner, making it possible to confine DNA probes with a level of control that is unparalleled using standard microspotting techniques. We focus on muCSs that support arrays comprising up to 2 x 48 spots, each being 45 mum in diameter. Substrates were fabricated from two hard thermoplastic materials, poly(methylmethacrylate) and a polycyclic olefin (e.g., Zeonor 1060R), which were both activated with 1-ethyl-3-[3-(dimethylamino)propyl]carbodiimide hydrochloride and N-hydroxysuccinimide to mediate covalent attachment of DNA molecules. The approach was exemplified by using 0.25-32 muM solutions of amino-modified oligonucleotides labeled with either Cy3 or Cy5 fluorescent dye in phosphate-buffered saline, allowing for a direct and sensitive characterization of the printed arrays. Solutions were incubated for durations of 1 to >48 h at 22, 30, and 40 degrees C to probe the conditions for obtaining uniform spots of high fluorescence intensity. The length (l) and depth (d) of microfluidic supply channels were both important with respect to depletion as well as evaporation of the solvent. While selective activation of the substrate proved helpful to limit unproductive loss of oligonucleotides along trajectories, incubation of solution in a humid environment was necessary to prevent uncontrolled drying of the liquid, keeping the immobilization process intact over extended periods of time. When combined, these strategies effectively promoted the formation of high-quality DNA arrays, making it possible to arrange multiple probes in parallel with a high degree of uniformity. Moreover, we show that resultant arrays are compatible with standard hybridization protocols, which allowed for reliable discrimination of individual strands when exposed to a specific ssDNA target molecule.

Spatial distribution of laminar flow-assisted dendritic amplification

In this paper, we report spatial distribution of laminar flow-assisted dendritic amplification (LFDA) product. LFDA is a recently invented signal amplification method dedicated to biomolecular binding events on microchannel walls. Onto the bound biomolecule, a dendritic structure is constructed by supplying two building blocks from laminar streams produced by a Y-shaped microchannel. In view of the extension of LFDA to simultaneous amplification of multiple binding spots, we have investigated the distribution of the LFDA product across and along the microchannel with the course of time. We fabricated a Y-shaped microchannel with a cross section of 110 microm x 22 microm using poly(dimethylsiloxane). As the LFDA building blocks, FITC-labeled streptavidin and biotinylated anti-streptavidin were injected from the two inlets of the microchannel at a mean flow velocity of 6.2 mm s(-1) (after the confluence). Nonspecific adsorption of the building blocks formed the seed layer of LFDA. The progress of LFDA was monitored with a fluorescence microscope up to 10.1 mm of microchannel length. After 5 min or later, the fluorescence intensity profile across the microchannel showed a peak at the center of the channel. With the course of time, the peak height grew exponentially except for slight saturation, but the peak width was almost constant. Along the microchannel, the peak height decreased almost linearly with the increasing logarithm of the distance, and the peak width was broadened in accordance with the 1/3 power law.

An integrated reaction-transport model for DNA surface hybridization: implications for DNA microarrays

DNA microarrays have the potential to revolutionize medical diagnostics and development of individualized medical treatments. However, accurate quantification of scantily expressed genes and precise measurement of small differences between different treatments is not currently feasible. A major challenge remains the understanding of physicochemical processes and rate-limiting steps of hybridization of complex mixtures of DNA targets on immobilized DNA probes. To this end, we developed a mathematical model to describe the effects of molecular orientation and transport on the kinetics and efficiency of hybridization. First, we calculated the hybridization rate constant based on the distance between the complementary nucleotides of the target and probe DNA. The surface reaction rate was then integrated with translational and rotational transport of target DNA to the surface to calculate the kinetics of hybridization. Our model predicts that hybridization of short DNA targets is diffusion limited but long targets are kinetically limited. In addition, for DNA targets with wide size distribution, it may be difficult to distinguish between specific binding of long targets from nonspecific binding of short ones. Our model provides novel insight into the process of DNA hybridization and suggests operating conditions to improve the sensitivity and accuracy of microarray experiments.

Automated analytical microarrays: a critical review

Microarrays provide a powerful analytical tool for the simultaneous detection of multiple analytes in a single experiment. The specific affinity reaction of nucleic acids (hybridization) and antibodies towards antigens is the most common bioanalytical method for generating multiplexed quantitative results. Nucleic acid-based analysis is restricted to the detection of cells and viruses. Antibodies are more universal biomolecular receptors that selectively bind small molecules such as pesticides, small toxins, and pharmaceuticals and to biopolymers (e.g. toxins, allergens) and complex biological structures like bacterial cells and viruses. By producing an appropriate antibody, the corresponding antigenic analyte can be detected on a multiplexed immunoanalytical microarray. Food and water analysis along with clinical diagnostics constitute potential application fields for multiplexed analysis. Diverse fluorescence, chemiluminescence, electrochemical, and label-free microarray readout systems have been developed in the last decade. Some of them are constructed as flow-through microarrays by combination with a fluidic system. Microarrays have the potential to become widely accepted as a system for analytical applications, provided that robust and validated results on fully automated platforms are successfully generated. This review gives an overview of the current research on microarrays with the focus on automated systems and quantitative multiplexed applications.

Nucleic acid microarrays created in the double-spiral format on a circular microfluidic disk

A microfluidic microarray that is created in the double spiral format has produced a greater density of probes than in our previous report. Using this double-spiral format together with centrifugal pumping for liquid delivery, 384 x 384 hybridization assays have been performed on one circular disk at one time, at the intersections between the spiral channels and spiral probe lines. Each sample was introduced into each inlet reservoir leading to 4 spiral channels and was analyzed independently, and so the hybridization results were self-corrected among the 4 spiral channels. In this work, fast microarray hybridizations have been successfully achieved by using both complementary oligonucleotides as well as PCR products prepared from plant fungal pathogen cultures.

Fungal pathogenic nucleic acid detection achieved with a microfluidic microarray device

Detection of polymerase chain reaction (PCR) products obtained from cultured greenhouse fungal pathogens, Botrytis cinerea and Didymella bryoniae has been achieved using a previously developed microfluidic microarray assembly (MMA) device. The flexible probe construction and rapid DNA detection resulted from the use of centrifugal pumping in the steps of probe introduction and sample delivery, respectively. The line arrays of the oligonucleotide probes were "printed" on a CD-like glass chip using a polydimethylsiloxane (PDMS) polymer plate with radial microfluidic channels, and the sample hybridizations were conducted within the spiral channels on the second plate. The experimental conditions of probe immobilization and sample hybridization were optimized, and both complementary oligonucleotides and PCR products were tested. We were able to achieve adequate fluorescent signals with a sample load as small as 0.5 nM (1 microL) for oligonucleotide samples; for PCR products, we achieved detection at the level of 3 ng.

Competitive immunoassays for simultaneous detection of metabolites and proteins using micromosaic patterning

New high-throughput immunoassay methods for rapid point-of-care diagnostic applications represent an unmet need and current focus of numerous innovative methods. We report a new micromosaic competitive immunoassay developed for the analysis of the thyroid hormone thyroxine (T4), inflammation biomarker C-reactive protein (CRP), and the oxidative damage marker 3-nitrotyrosine (BSA-3NT) on a silicon nitride substrate. To demonstrate the versatility of the method, both direct and indirect format competitive immunoassays were developed and could be applied simultaneously for single samples. Signals from standard solutions were fit to a logistic equation, allowing simultaneous detection of T4 (7.7-257.2 nM), CRP (0.3-4.2 microg/mL), and BSA-3NT (0.03-22.3 microg/mL). Total assay time including sample introduction, washing, and fluorescence measurement was less than 45 min. Dissociation constants for affinity pairs in the system have been estimated using regression. This proof-of-concept experiment shows that both small and macromolecular biomarkers can be quantified from a single sample using the method and suggests that groups of clinically related analytes may be analyzed by competitive micromosaic immunoassay techniques.

Flexible microarray construction and fast DNA hybridization conducted on a microfluidic chip for greenhouse plant fungal pathogen detection

This study employed a microfluidic method in which probe creation does not require pin-spotting and fast hybridization is conducted on the same microarray chip for the detection of three greenhouse pathogens ( Botrytis cinerea, Didymella bryoniae, and Botrytis squamosa). In this method, 16 oligonucleotide probe line arrays were created on a glass substrate by a microfluidic printing method. Then, low amounts of the DNA samples (1 fmol of oligonucelotides or 1.4 ng of PCR products) were introduced into the microchannels that were orthogonal to these probe lines. The hybridizations of 16 samples (21-mer complementary oligonuleotides and approximately 260 bp PCR products) were fulfilled at the channel-probe line intersections and in a short time (minutes). The optimization of probe immobilization and sample hybridization are described in detail. The method successfully detected and discriminated between two 260 bp PCR products with a one-base-pair difference from closely related greenhouse plant fungal pathogens (B. cinerea and B. squamosa).