On-line sample pre-concentration in microfluidic devices: a review

3D Paper-Based Origami Device for Programmable Multifold Analyte Preconcentration

In analytical chemistry, preconcentration represents a critical step able to enhance the accuracy of detection; however, the experimental procedures needed to preconcentrate samples might be characterized by drawbacks regarding the whole analytical process, e.g., being complex, invasive, and/or time-consuming. In this study, a novel 3D paper-based origami device is introduced for multifold analyte preconcentration. Leveraging the benefits of paper-based substrates, the proposed architecture boosts sample preconcentration while minimizing time and tasks for measurements, solely by exploiting the porous and versatile nature of paper-based substrates. In comparison with other paper-based approaches reported in the literature for preconcentration, the present architecture offers the ability to be programmed for obtaining the needed sensitivity increase without sacrificing measurement time. To demonstrate the efficacy of the novel approach, the 3D paper-based origami device was deeply characterized, including the most relevant parameters, i.e., disk size and number, unfolding time, and volume, and subsequently applied for the preconcentration and the detection of various analytes in real matrices, namely, mercury in tap water and glucose in sweat, resulting in a 400% and 300% sensitivity enhancement, respectively. This innovative preconcentration tool addresses the limitations of existing conventional methods, providing increased sensitivity without the use of expensive and time-consuming procedures through only exploiting the intrinsic properties of paper-based substrates and a rationale design. The proposed architecture emerges as a universal tool to be adopted and programmed for various analytical systems and fields of application.

An overview of preconcentration techniques combined with inductively coupled plasma mass spectrometry for trace element determination in biological studies

In the last decades, the determination of trace elements in biological materials has emerged as an important area of study because of its relevance to human health and the environment. Inductively coupled plasma mass spectrometry (ICP-MS) has proven to be a powerful tool for trace element analysis, owing to its high sensitivity and ability to determine several elements in a single measurement. However, given the complex nature of biological matrices and the presence of elements, most of them at ultratrace levels, it becomes crucial to complement ICP-MS with preconcentration techniques to increase the sensitivity and selectivity of analytical methods. This article presents an exhaustive overview of liquid- and solid-phase preconcentration techniques used in combination with ICP-MS for trace element determination in different biological samples from 2000 to the present. An in-depth discussion of the advances on the application of state-of-the-art solvents and materials in trace element extraction and preconcentration is presented. Special attention is given to different strategies for elemental speciation analysis, employing both chromatographic and non-chromatographic techniques. The role of automation in these methodologies is also described. Finally, future trends and challenges related to this topic are discussed.

Microfluidic chip and chiroptical gold nanoparticle-based colorimetric sensor for enantioselective detection of L-tryptophan

Herein, we introduce a novel integrated system that merges an enantio-discriminative bio-MOF-packed centrifugal microfluidic chip made from PDMS with a user-friendly on-site colorimetric sensor. This innovative approach enables the precise enantioselective recognition of L-tryptophane (L-Trp). This chiral recognition probe was successfully synthesized through meticulous control of nano-ovals-shaped gold nanoparticles morphology and surface passivation. The operational factor of this methodology was optimized to ensure simplicity, practicality, and efficiency. This optimization led to reduced reagent consumption and instantaneous analytical feedback. The integrated system was effectively applied for enantioselective separation and quantification of L-Trp across an extensive linear range of 50 μM-1.5 mM, impressive limit of detection as low as 15 μM. It is noteworthy that this integrated system demonstrated desirable selectivity even in the presence of similar biomolecules, showcasing its robust performance and rapid detection capability. Further extended the application of this strategy to exceptional performance across enantioselective sensing of L-Trp in various sample matrices, comprising bovine serum albumin, bovine milk, blood plasma and urine samples. This integrated microfluidic sample pretreatment, chiroptical sensing, and on-site signal recording with a smartphone hold tremendous potential for widespread implementation, practical applications engaging healthcare and environmental, food safety, and point-of-needs analysis, facilitating successive solution mixing and colorimetric detection.

High-throughput microfluidic chip with silica gel-C18 channels for cyclotide separation

Over the past two decades, microfluidic-based separations have been used for the purification, isolation, and separation of biomolecules to overcome difficulties encountered by conventional chromatography-based methods including high cost, long processing times, sample volumes, and low separation efficiency. Cyclotides, or cyclic peptides used by some plant families as defense agents, have attracted the interest of scientists because of their biological activities varying from antimicrobial to anticancer properties. The separation process has a critical impact in terms of obtaining pure cyclotides for drug development strategies. Here, for the first time, a mimic of the high-performance liquid chromatography (HPLC) on microfluidic chip strategy was used to separate the cyclotides. In this regard, silica gel-C18 was synthesized and characterized by Fourier-transform infrared spectroscopy (FTIR) and proton nuclear magnetic resonance (1H-NMR) and then filled inside the microchannel to prepare an HPLC C18 column-like structure inside the microchannel. Cyclotide extract was obtained from Viola ignobilis by a low voltage electric field extraction method and characterized by HPLC and matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF). The extract that contained vigno 1, 2, 3, 4, 5, and varv A cyclotides was added to the microchannel where distilled water was used as a mobile phase with 1 µL/min flow rate and then samples were collected in 2-min intervals until 10 min. Results show that cyclotides can be successfully separated from each other and collected from the microchannel at different periods of time. These findings demonstrate that the use of microfluidic channels has a high impact on the separation of cyclotides as a rapid, cost-effective, and simple method and the device can find widespread applications in drug discovery research.

Sample preconcentration through airjet-induced liquid phase enrichment

Sample preparation is essential for nucleic acid assays, affecting their sensitivity and reliability. However, this process often results in a significant loss or dilution of the analyte, which becomes a bottleneck that limits downstream assay performance, particularly for assays that accept a limited input sample volume. To overcome this challenge, we present an evaporative-based sample enrichment method that uses an airjet to concentrate analytes within a small, defined volume by reversing the coffee-ring effect. A small, concentrated sample can then be collected for analysis to increase the initial sample load. The effectiveness of the reported airjet enrichment was quantified using qPCR of λ-DNA, HeLa-S3 RNA, and heat-inactivated SARS-CoV-2 samples. Comparisons between airjet enrichment and conventional evaporative concentration methods demonstrated significant advantages of airjet enrichment, including the ability to concentrate a high percentage of analyte within a 1 μL volume. The enrichment method was then integrated and adapted for various fluid volumes commonly found in nucleic acid sample preparation procedures. Here, airjet enrichment reduced the overall Cq by an average of 9.27 cycles for each analyte, resulting in a 600-fold enrichment from the initial concentration. To perform selective enrichment and prevent salt-based interference in downstream analysis, PEG was added to reduce the co-enrichment of salt. In addition, a preliminary study was conducted to explore the integration of airjet enrichment into ELISA using rabbit IgG as a model antigen. These findings demonstrate how airjet enrichment can be easily integrated into existing laboratory protocols with minimal modification and significantly improve the performance of biosensors.

Improving greenness and sustainability of standard analytical methods by microextraction techniques: A critical review

Since environmental awareness has increased in analytical chemistry, the demand for green sample preparation methods continues to grow. Microextractions such as solid-phase microextraction (SPME) and liquid-phase microextraction (LPME) miniaturize the pre-concentration step and are a more sustainable alternative to conventional large-scale extractions. However, the integration of microextractions in standard and routine analysis methods is rare, although these applications are used most frequently and have a role model function. Therefore, it is important to highlight that microextractions are capable to replace large-scale extractions in standard and routine methods. This review discusses the greenness, benefits, and drawbacks of the most common LPME and SPME variants compatible with gas chromatography based on the following key evaluation principles: Automation, solvent consumption, hazards, reusability, energy consumption, time efficiency, and handling. Furthermore, the need to integrate microextractions into standard and routine analytical methods is presented by using method greenness evaluation metrics AGREE, AGREEprep, and GAPI applied to USEPA methods and their replacements.

Hand-Powered Inertial Microfluidic Syringe-Tip Centrifuge

Conventional sample preparation techniques require bulky and expensive instruments and are not compatible with next-generation point-of-care diagnostic testing. Here, we report a manually operated syringe-tip inertial microfluidic centrifuge (named i-centrifuge) for high-flow-rate (up to 16 mL/min) cell concentration and experimentally demonstrate its working mechanism and performance. Low-cost polymer films and double-sided tape were used through a rapid nonclean-room process of laser cutting and lamination bonding to construct the key components of the i-centrifuge, which consists of a syringe-tip flow stabilizer and a four-channel paralleled inertial microfluidic concentrator. The unstable liquid flow generated by the manual syringe was regulated and stabilized with the flow stabilizer to power inertial focusing in a four-channel paralleled concentrator. Finally, we successfully used our i-centrifuge for manually operated cell concentration. This i-centrifuge offers the advantages of low device cost, simple hand-powered operation, high-flow-rate processing, and portable device volume. Therefore, it holds potential as a low-cost, portable sample preparation tool for point-of-care diagnostic testing.

Electroosmotic Flow Hysteresis for Fluids with Dissimilar pH and Ionic Species

Electroosmotic flow (EOF) involving displacement of multiple fluids is employed in micro-/nanofluidic applications. There are existing investigations on EOF hysteresis, i.e., flow direction-dependent behavior. However, none so far have studied the solution pair system of dissimilar ionic species with substantial pH difference. They exhibit complicated hysteretic phenomena. In this study, we investigate the EOF of sodium bicarbonate (NaHCO₃, alkaline) and sodium chloride (NaCl, slightly acidic) solution pair via current monitoring technique. A developed slip velocity model with a modified wall condition is implemented with finite element simulations. Quantitative agreements between experimental and simulation results are obtained. Concentration evolutions of NaHCO₃-NaCl follow the dissimilar anion species system. When NaCl displaces NaHCO₃, EOF reduces due to the displacement of NaHCO₃ with high pH (high absolute zeta potential). Consequently, NaCl is not fully displaced into the microchannel. When NaHCO₃ displaces NaCl, NaHCO₃ cannot displace into the microchannel as NaCl with low pH (low absolute zeta potential) produces slow EOF. These behaviors are independent of the applied electric field. However, complete displacement tends to be achieved by lowering the NaCl concentration, i.e., increasing its zeta potential. In contrast, the NaHCO₃ concentration has little impact on the displacement process. These findings enhance the understanding of EOF involving solutions with dissimilar pH and ion species.

Microfluidics for Peptidomics, Proteomics, and Cell Analysis

Microfluidics is the advanced microtechnology of fluid manipulation in channels with at least one dimension in the range of 1-100 microns. Microfluidic technology offers a growing number of tools for manipulating small volumes of fluid to control chemical, biological, and physical processes relevant to separation, analysis, and detection. Currently, microfluidic devices play an important role in many biological, chemical, physical, biotechnological and engineering applications. There are numerous ways to fabricate the necessary microchannels and integrate them into microfluidic platforms. In peptidomics and proteomics, microfluidics is often used in combination with mass spectrometric (MS) analysis. This review provides an overview of using microfluidic systems for peptidomics, proteomics and cell analysis. The application of microfluidics in combination with MS detection and other novel techniques to answer clinical questions is also discussed in the context of disease diagnosis and therapy. Recent developments and applications of capillary and microchip (electro)separation methods in proteomic and peptidomic analysis are summarized. The state of the art of microchip platforms for cell sorting and single-cell analysis is also discussed. Advances in detection methods are reported, and new applications in proteomics and peptidomics, quality control of peptide and protein pharmaceuticals, analysis of proteins and peptides in biomatrices and determination of their physicochemical parameters are highlighted.

Simultaneous determination of total phenolic acids and total flavonoids in tea and honey samples using an integrated lab on a chip device

A microfluidic device for simultaneous analysis of total flavonoids and total phenolic acids is presented for the first time. The process was based on the utilization of magnetic zinc-imidazole frameworks (ZIF-4), as a highly efficient media for on-line separation of phenolic acids and flavonoids, which were subsequently detected by a sensitive chemiluminescence (CL) method. Acrylate-based polymeric microchips containing a separation column (12.5 mm length, 3 mm width and 1 mm depth) were fabricated using a 3D-printer, and magnetic ZIF-4 was fixed into the column. The high porosity of the magnetic ZIF-4 made it a suitable adsorbent, guaranteeing an effective separation. The detection limits were in the range of 0.04-0.10 µg mL^-1 with relative standard deviation values of (2.19-4.38%). The system was successfully applied for the analysis of flavonoids and phenolic acids in tea and honey samples. The recovery was from 95.4 to 104.1%, indicating a good accuracy of the developed method.

Analysis of pressure-driven membrane preconcentration for point-of-care assays

Point-of-care diagnostic devices for both physicians and patients themselves are now ubiquitous, but often not sensitive enough for highly dilute analytes (e.g., pre-symptomatic viral detection). Two primary methods to address this challenge include (1) increasing the sensitivity of molecular recognition elements with greater binding affinity to the analyte or (2) increasing the concentration of the analyte being detected in the sample itself (preconcentration). The latter approach, preconcentration, is arguably more attractive if it can be made universally applicable to a wide range of analytes. In this study, pressure-driven membrane preconcentration devices were developed, and their performance was analyzed for detecting target analytes in biofluids in the form of point-of-care lateral-flow assays (LFAs). The demonstrated prototypes utilize negative or positive pressure gradients to move both water and small interferents (salt, pH) through a membrane filter, thereby concentrating the analyte of interest in the remaining sample fluid. Preconcentration up to 33× is demonstrated for influenza A nucleoprotein with a 5 kDa pore polyethersulfone membrane filter. LFA results are obtained within as short as several minutes and device operation is simple (very few user steps), suggesting that membrane preconcentration can be preferable to more complex and slow conventional preconcentration techniques used in laboratory practice.

Electrokinetic stacking of particle zones in confined channels enabling their UV absorbance detection on microchips

In this article, we report a simple approach to stacking micro- and nanoparticle zones by electrokinetically migrating them through moderately confined channels of uniform cross-section. Experiments show the reported pre-concentration process to initiate at the tail end of the zone following its electrokinetic injection, with the stacked region migrating faster than the rest of the sample band. This effect causes the particles traveling in front to merge into the stacked region making it grow both in size and concentration. Because the stacked zone also gradually loses particles from its trailing edge, it eventually disintegrates upon running out of particles at its front end. Nevertheless, enhancements in peak height by over 100-fold were recorded using the reported approach for polystyrene beads with diameters comparable to the channel depth. This enhancement however, exhibited a temporal variation as the particle band migrated through the analysis column reaching a maximum value that depended on the particle diameter, particle concentration, channel depth, electric field strength, electroosmotic mobility, etc. Interestingly, the peak area recorded by the detector remained relatively constant during this particle migration period allowing reliable sample quantitation. Moreover, upon incubating antibody-coated particles against an antigen sample, the peak area for the particle zone was seen to scale linearly with the antigen concentration establishing the utility of the reported focusing phenomenon for chemical/biochemical analysis. The noted stacking technique was further applied to enabling UV absorbance detection of particle zones on microchips which then allowed us to determine the colloidal content in actual natural water samples. .

Application of a Micro Free-Flow Electrophoresis 3D Printed Lab-on-a-Chip for Micro-Nanoparticles Analysis

The present work describes a novel microfluidic free-flow electrophoresis device developed by applying three-dimensional (3D) printing technology to rapid prototype a low-cost chip for micro- and nanoparticle collection and analysis. Accurate reproducibility of the device design and the integration of the inlet and outlet ports with the proper tube interconnection was achieved by the additive manufacturing process. Test prints were performed to compare the glossy and the matte type of surface finish. Analyzing the surface topography of the 3D printed device, we demonstrated how the best reproducibility was obtained with the glossy device showing a 5% accuracy. The performance of the device was demonstrated by a free-flow zone electrophoresis application on micro- and nanoparticles with different dimensions, charge surfaces and fluorescent dyes by applying different separation voltages up to 55 V. Dynamic light scattering (DLS) measurements and ultraviolet−visible spectroscopy (UV−Vis) analysis were performed on particles collected at the outlets. The percentage of particles observed at each outlet was determined in order to demonstrate the capability of the micro free-flow electrophoresis (µFFE) device to work properly in dependence of the applied electric field. In conclusion, we rapid prototyped a microfluidic device by 3D printing, which ensured micro- and nanoparticle deviation and concentration in a reduced operation volume and hence suitable for biomedical as well as pharmaceutical applications.

A reusable PMMA/paper hybrid plug-and-play microfluidic device for an ultrasensitive immunoassay with a wide dynamic range

Conventional colorimetric enzyme-linked immunosorbent assay (ELISA) is a time-consuming laboratory assay that is not very sensitive and consumes a large amount of samples. Herein, the development of a reusable, cost-effective, and eco-friendly poly(methyl methacrylate) (PMMA)/paper hybrid plug-and-play (PnP) device for high-sensitivity immunoassay by analyte enrichment and efficient passing-through washing has been reported. The PMMA device has multiple slots where a pre-patterned paper substrate can be inserted. The sample flows back-and-forth through a low-cost, 3D paper substrate within the PMMA channels, thereby enhancing the amount of analyte adsorbed and dramatically increasing the sensitivity while decreasing the assay time. After the enrichment assay, the paper substrate can simply be pulled out of the device, and the results can be qualitatively viewed with the naked eye or scanned through a simple desktop scanner for quantitative analysis. The paper substrate can be replaced with a new substrate so that the device can be reused. The limits of detection (LODs) of 200 pg/mL for immunoglobulin G (IgG) and 270 pg/mL for hepatitis B surface antigen (HBsAg) were obtained. This IgG assay is at least 10 times more sensitive than commercial ELISA kits. In addition, the PnP ELISA exhibited a significant increase in the linear dynamic range from 3 orders of magnitude in a common paper-based device to a wide range of six orders of magnitude in the PnP hybrid device. This reusable PnP device has great potential for the low-cost yet high-sensitivity detection of infectious diseases, cancers, and other important biomolecules.

Characterization of Pieces of Paper That Form Reagent Containers for Use as Portable Analytical Devices

Reagent-deposited pieces of paper were characterized by the use of a compact conductometer, a compact pH sensor, and a conventional spectrophotometer to assess their suitability for use as reagent containers. The pieces of paper were fabricated by wax printing to form a limited hydrophilic area to which a consistent volume of an aqueous reagent could be added. The pieces of paper without the reagent increased the conductivity of water gradually because of the release of sodium salts, whereas pH of NaOH decreased because of the acidity of the functional groups in the paper. Three reagents, sulfamic acid as an acid, Na₂CO₃ as a base, and BaCl₂ as a metal salt, were deposited on the pieces of paper to evaluate their ability to release from the pieces of paper. Sulfamic acid and Na₂CO₃ were released in quantities of 58 and 73% into water after 420 s, whereas 100% of BaCl₂ was released after 480 s. The conductometric titrations of NaOH, HCl, and Na₂SO₄, and the spectrophotometry of Fe²⁺ were examined using the pieces of paper that contained sulfamic acid, Na₂CO₃, BaCl₂, and 1,10-phenanthroline. Titrations using the pieces of paper suggested that the reagents were quantitatively released into the titrant, which resulted in a linear relationship between the endpoints and the equivalent points. In 120 s of soaking time, 60-70% of the reagents were released. The spectrophotometric measurements of Fe²⁺ indicated that when an excess amount of the reagents was deposited onto the pieces of paper, they nonetheless sufficiently fulfilled the role of a reagent container.

On-chip ion pair-based dispersive liquid-liquid extraction for quantitative determination of histamine H2 receptor antagonist drugs in human urine

In the present work, an ion-pair based dispersive liquid-liquid microextraction was performed on a centrifugal chip for the first time. The entire DLLME procedure, including flow direction, desperation, and sedimentation of the extracting phase, can be fulfilled automatically on a solitary chip. The chip was made of Poly(methyl methacrylate) (PMMA) and was of two units for two parallel extractions, each consisting of three chambers (for the sample solution, extracting solvents, and sedimentation). As the chip rotated, fluids flowed within the chip, and the dispersion, mixing, extraction, and sedimentation of the final phase were performed on the chip by simply adjusting the spin speed. Determination of two histamine H₂ receptor antagonist drugs, cimetidine and ranitidine, as the model analytes from the urine samples was done using the developed on-chip ion-pair based DLLME method followed by an HPLC-UV. The effective parameters on the extraction efficiency of the model analytes were investigated and optimized using the one variable at a time method. Under optimized conditions, the calibration curve was linear in the range of 15-2000 μg L^-1 with a coefficient of determination (R²) more than 0.9987. The relative standard deviations (RSD %) for extraction and determination of the analytes were less than 3.7% based on five replicated measurements. LODs less than 10.0 μg L^-1 and preconcentration factors higher than 39-fold were obtained for both of the model analytes. The proposed chip enjoys the advantages of both the DLLME method and miniaturization on a centrifugal chip.

Extraction, Enrichment, and in situ Electrochemical Detection on Lab-on-a-Disc: Monitoring the Production of a Bacterial Secondary Metabolite

Development of microsystems, which enable "sample-to-answer" detection from real samples, is often challenging. We present the first integration of supported liquid membrane extraction combined with electrochemical detection on a centrifugal fluidic platform. The developed lab-on-a-disc (LoD) system enabled the separation, enrichment, and subsequent electrochemical detection of the target analyte from a complex sample mixture. As a case study, we quantified the amount of a dietary supplement and pharmaceutical precursor, p-coumaric acid, from bacterial growth media at different time points during production. The assay, extraction, and detection, performed on the LoD device, proved to be a low cost and environmentally friendly approach, requiring only a few tens of microliters of organic solvent and enabled detection in a 3 μL volume. In addition, the data obtained from the centrifugal platform showed a good correlation with data obtained from the high performance liquid chromatography analysis.

Continuous, quantifiable, and simple osmotic preconcentration and sensing within microfluidic devices

Insurmountable detection challenges will impede the development of many of the next-generation of lab-on-a-chip devices (e.g., point-of-care and real-time health monitors). Here we present the first membrane-based, microfluidic sample preconcentration method that is continuous, quantifiable, simple, and capable of working with any analyte. Forward osmosis rapidly concentrates analytes by removing water from a stream of sample fluid. 10-100X preconcentration is possible in mere minutes. This requires careful selection of the semi-permeable membrane and draw molecule; therefore, the osmosis performance of several classes of membranes and draw molecules were systematically optimized. Proof-of-concept preconcentration devices were characterized based on their concentration ability and fouling resistance. In-silico theoretical modeling predicts the experimental findings and provides an engineering toolkit for future designs. With this toolkit, inexpensive ready-for-manufacturing prototypes were also developed. These devices provide broad-spectrum detection improvements across many analytes and sensing modalities, enabling next-generation lab-on-a-chip devices.

On-line sample preconcentration by polarity switching in floating electrode-integrated microchannel

In this study, we found that the polarity switching was effective to enrich and separate fluorescent analytes which have weakly-dissociated groups in a floating platinum electrode (width, 50 µm; thickness, 2.5 µm)-integrated straight-channel in microchip electrophoresis (MCE). In the straight channel filled with an Alexa Flour 488 (AF488) solution, a sharp peak was observed after the polarity inversion with a 530-fold enhancement of the sensitivity relative to the conventional MCE analysis. By using a fluorescent pH indicator, we verified that a sharp high-pH zone was generated nearby the floating electrode and moved toward the anode with maintaining the high pH, which induced the sample enrichment like a dynamic pH junction mechanism. In the floating electrode-embedded channel, the mixture of AF488-labeled proteins was also well concentrated and separated within 100 s.

Microfluidic Preconcentration Chip with Self-Assembled Chemical Modified Surface for Trace Carbonyl Compounds Detection

Carbonyl compounds in water sources are typical characteristic pollutants, which are important indicators in the health risk assessment of water quality. Commonly used analytical chemistry methods face issues such as complex operations, low sensitivity, and long analysis times. Here, we report a silicon microfluidic device based on click chemical surface modification that was engineered to achieve rapid, convenient and efficient capture of trace level carbonyl compounds in liquid solvent. The micro pillar arrays of the chip and microfluidic channels were designed under the basis of finite element (FEM) analysis and fabricated by the microelectromechanical systems (MEMS) technique. The surface of the micropillars was sputtered with precious metal silver and functionalized with the organic substance amino-oxy dodecane thiol (ADT) by self-assembly for capturing trace carbonyl compounds. The detection of ppb level fluorescent carbonyl compounds demonstrates that the strategy proposed in this work shows great potential for rapid water quality testing and for other samples with trace carbonyl compounds.

Recent advances in enhancing the sensitivity of electrophoresis and electrochromatography in capillaries and microchips (2016-2018)

One of the most cited limitations of capillary and microchip electrophoresis is the poor sensitivity. This review continues to update this series of biannual reviews, first published in Electrophoresis in 2007, on developments in the field of online/in-line concentration methods in capillaries and microchips, covering the period July 2016-June 2018. It includes developments in the field of stacking, covering all methods from field-amplified sample stacking and large-volume sample stacking, through to isotachophoresis, dynamic pH junction, and sweeping. Attention is also given to online or in-line extraction methods that have been used for electrophoresis.

The microemulsion electrokinetic capillary chromatography combined with reversed-electrode polarity stacking mode for enriching and quantifying lignanoids and ginsenosides in TCMs preparation Shengmai injection

An on-line large volume sample stacking with polarity switching (LVSS) method was proposed for simultaneously determining lignanoids and ginsenosides in MEEKC. The parameters including the pH value and concentration of buffer solution, SDS, organic modifier, oil phase, running voltage, and temperature as well as injection time, sample matrix, stacking voltage, and time influencing separation and stacking were systematically optimized. The method was verified by performing precision, accuracy, stability, and recovery. Its reliability was proved by separating and quantifying two lignanoids and three ginsenosides in Shengmai injectionSMI. The sensitivity of these compounds was improved by MEEKC-LVSS method for 6-11 times than conventional MEEKC. Thus, this developed on-line MEEKC-LVSS method was sensitive, practical, and reliable.

3D-Printed Microflow Injection Analysis Platform for Online Magnetic Nanoparticle Sorptive Extraction of Antimicrobials in Biological Specimens as a Front End to Liquid Chromatographic Assays

In this work, the concept of 3D-printed microflow injection (3D-μFI) embodying a dedicated multifunctional 3D-printed stator onto a rotary microvalve along with a mesofluidic sample preparation platform is proposed for the first time. A transparent 3D-printed stereolithographic mesofluidic chip device accommodating polyaniline (PANI) decorated magnetic nanoparticles (32.5 ± 3.8 mg) is harnessed to in-line sorptive microextraction as a front end to liquid chromatography with peak focusing. As a proof-of-concept application, the 3D-μFI assembly was resorted to matrix cleanup and automatic programmable-flow determination of organic emerging contaminants (4-hydroxybenzoate analogues and triclosan as antimicrobial model analytes) in human saliva and urine samples. By using a sample volume of 1.0 mL with a loading flow rate of 200 μL min^-1, an eluent volume of 120 μL at 80 μL min^-1, and online HPLC injection of 300 μL of the mixture of eluate and Milli-Q water (in a 1:2 ratio) to prevent band broadening effects of the most polar analytes, the limits of detection (3σ criterion) ranged from 1.1 to 4.5 ng mL^-1 for methylparaben (MP), ethylparaben (EP), propylparaben (PrP), phenylparaben (PhP), butylparaben (BP), and triclosan (TCS). Enhancement factors of 16-25 were obtained for the target analytes. Spike recoveries ranged from 84 to 117% for both saliva and urine samples. The online 3D-μFI hyphenated method is synchronized with the chromatographic separation and features a chip lifetime of more than 20 injections with minimal losses of moderately nonpolar compounds on the walls of the mesofluidic device.

Molecular rheotaxis directs DNA migration and concentration against a pressure-driven flow

In-line preconcentration techniques are used to improve the sensitivity of microfluidic DNA analysis platforms. The most common methods are electrokinetic and require an externally applied electric field. Here we describe a microfluidic DNA preconcentration technique that does not require an external field. Instead, pressure-driven flow from a fluid-filled microcapillary into a lower ionic strength DNA sample reservoir induces spontaneous DNA migration against the direction of flow. This migratory phenomenon that we call Molecular Rheotaxis initiates in seconds and results in a concentrated DNA bolus at the capillary orifice. We demonstrate the ease with which this concentration method can be integrated into a microfluidic total analysis system composed of in-line DNA preconcentration, size separation, and single-molecule detection. Paired experimental and numerical simulation results are used to delineate the parameters required to induce Molecular Rheotaxis, elucidate the underlying mechanism, and optimize conditions to achieve DNA concentration factors exceeding 10,000 fold.

Implementing a nucleic acid preconcentration method can improve the sensitivity of microfluidic analysis systems. Here Friedrich et al. concentrate DNA by many orders of magnitude using pressure-driven flow, which could lead to a simple and practical microanalysis platform.

New nucleic acid testing devices to diagnose infectious diseases in resource-limited settings

Point-of-care diagnosis based on nucleic acid testing aims to incorporate all the analytical steps, from sample preparation to nucleic acid amplification and detection, in a single device. This device needs to provide a low-cost, robust, sensitive, specific, and easily readable analysis. Microfluidics has great potential for handling small volumes of fluids on a single platform. Microfluidic technology has recently been applied to paper, which is already used in low-cost lateral flow tests. Nucleic acid extraction from a biological specimen usually requires cell filtration and lysis on specific membranes, while affinity matrices, such as chitosan or polydiacetylene, are well suited to concentrating nucleic acids for subsequent amplification. Access to electricity is often difficult in resource-limited areas, so the amplification step needs to be equipment-free. Consequently, the reaction has to be isothermal to alleviate the need for a thermocycler. LAMP, NASBA, HDA, and RPA are examples of the technologies available. Nucleic acid detection techniques are currently based on fluorescence, colorimetry, or chemiluminescence. For point-of-care diagnostics, the results should be readable with the naked eye. Nowadays, interpretation and communication of results to health professionals could rely on a smartphone, used as a telemedicine device. The major challenge of creating an "all-in-one" diagnostic test involves the design of an optimal solution and a sequence for each analytical step, as well as combining the execution of all these steps on a single device. This review provides an overview of available materials and technologies which seem to be adapted to point-of-care nucleic acid-based diagnosis, in low-resource areas.

Fully Automatic In-Syringe Magnetic Stirring-Assisted Dispersive Liquid-Liquid Microextraction Hyphenated to High-Temperature Torch Integrated Sample Introduction System-Inductively Coupled Plasma Spectrometer with Direct Injection of the Organic Phase

A proof of concept study involving the online coupling of automatic dispersive liquid-liquid microextraction (DLLME) to inductively coupled plasma optical emission spectrometry (ICP OES) with direct introduction and analysis of the organic extract is herein reported for the first time. The flow-based analyzer features a lab-in-syringe (LIS) setup with an integrated stirring system, a Meinhard nebulizer in combination with a heated single-pass spray chamber, and a rotary injection valve, used as an online interface between the microextraction system and the detection instrument. Air-segmented flow was used for delivery of a fraction of the nonwater miscible extraction phase, 12 μL of xylene, to the nebulizer. All sample preparative steps including magnetic stirring assisted DLLME were carried out inside the syringe void volume as a size-adaptable yet sealed mixing and extraction chamber. Determination of trace level concentrations of cadmium, copper, lead, and silver as model analytes has been demonstrated by microextraction as diethyldithiophosphate (DDTP) complexes. The automatic LIS-DLLME method features quantitative metal extraction, even in troublesome sample matrixes, such as seawater, salt, and fruit juices, with relative recoveries within the range of 94-103%, 93-100%, and 92-99%, respectively. Furthermore, no statistically significant differences at the 0.05 significance level were found between concentration values experimentally obtained and the certified values of two serum standard reference materials.

A lab-on-a-chip for monolith-based preconcentration and electrophoresis separation of phosphopeptides

A real μTAS integrating monolith-based IMAC enrichment, electrophoresis separation and fluorescence detection of phosphopeptides is reported for the first time.

Solid supports for extraction and preconcentration of proteins and peptides in microfluidic devices: A review

Determination of proteins and peptides is among the main challenges of today's bioanalytical chemistry. The application of microchip technology in this field is an exhaustively developed concept that aims to create integrated and fully automated analytical devices able to quantify or detect one or several proteins from a complex matrix. Selective extraction and preconcentration of targeted proteins and peptides especially from biological fluids is of the highest importance for a successful realization of these microsystems. Incorporation of solid structures or supports is a convenient solution employed to face these demands. This review presents a critical view on the latest achievements in sample processing techniques for protein determination using solid supports in microfluidics. The study covers the period from 2006 to 2015 and focuses mainly on the strategies based on microbeads, monolithic materials and membranes. Less common approaches are also briefly discussed. The reviewed literature suggests future trends which are discussed in the concluding remarks.

On-Chip Fluorescent Labeling using Reversed-phase Monoliths and Microchip Electrophoretic Separations of Selected Preterm Birth Biomarkers

On-chip preconcentration, purification, and fluorescent labeling are desirable sample preparation steps to achieve complete automation in integrated microfluidic systems. In this work, we developed electrokinetically operated microfluidic devices for solid-phase extraction and fluorescent labeling of preterm birth (PTB) biomarkers. Reversed-phase monoliths based on different acrylate monomers were photopolymerized in cyclic olefin copolymer microdevices and studied for the selective retention and elution of a fluorescent dye and PTB biomarkers. Octyl methacrylate-based monoliths with desirable retention and elution characteristics were chosen and used for on-chip fluorescent labeling of three PTB biomarkers. Purification of on-chip labeled samples was done by selective elution of unreacted dye prior to sample. Automated and rapid on-chip fluorescent labeling was achieved with similar efficiency to that obtained for samples labeled off chip. Additionally, protocols for microchip electrophoresis of several off-chip-labeled PTB biomarkers were demonstrated in poly(methyl methacrylate) microfluidic devices. This study is an important step toward the development of integrated on-chip labeling and separation microfluidic devices for PTB biomarkers.

Analysis of proteins and peptides by electromigration methods in microchips

This review presents the developments and applications of microchip electromigration methods in the separation and analysis of peptides and proteins in the period 2011-mid-2016. The developments in sample preparation and preconcentration, microchannel material, and surface treatment are described. Separations by various microchip electromigration methods (zone electrophoresis in free and sieving media, affinity electrophoresis, isotachophoresis, isoelectric focusing, electrokinetic chromatography, and electrochromatography) are demonstrated. Advances in detection methods are reported and novel applications in the areas of proteomics and peptidomics, quality control of peptide and protein pharmaceuticals, analysis of proteins and peptides in biomatrices, and determination of physicochemical parameters are shown.

Electroosmotic Flow Hysteresis for Dissimilar Anionic Solutions

Electroosmotic flow (EOF) with two or more fluids is often encountered in various microfluidic applications. However, no investigation has hitherto been conducted to investigate the hysteretic or flow direction-dependent behavior during displacement flow of solutions with dissimilar anion species. In this investigation, EOF of dissimilar anionic solutions was studied experimentally through the current monitoring method and numerically through finite element simulations. As opposed to other conventional displacement flows, EOF involving dissimilar anionic solutions exhibits counterintuitive behavior, whereby the current-time curve does not reach the steady-state value of the displacing electrolyte. Two distinct mechanics have been identified as the causes for this observation: (a) ion concentration adjustment when the displacing anions migrate upstream against EOF due to competition between the gradients of electromigrative and convective fluxes and (b) ion concentration readjustment induced by the static diffusive interfacial region between the dissimilar fluids which can only be propagated throughout the entire microchannel with the presence of EOF. The resultant ion distributions lead to the flow rate to be directional-dependent, indicating that the flow conditions are asymmetric between these two different flow directions. The outcomes of this investigation contribute to the in-depth understanding of flow behavior in microfluidic systems involving inhomogeneous fluids, particularly dissimilar anionic solutions. The understanding of EOF hysteresis is fundamentally important for the accurate prediction of analytes transport in microfluidic devices under EOF.

Extraction for analytical scale sample preparation (IUPAC Technical Report)

Approaches for sample preparation are developing rapidly as new strategies are implemented to improve sample throughput and to minimize material and solvent use in laboratory methods and to develop on-site capabilities. In majority of cases the key step in sample preparation is extraction, typically used to separate and enrich compounds of interests from the matrix in the extraction phase. In this contribution, the topic of analytical scale extraction is put in perspective emphasising the fundamental aspects of the underlying processes discussing the similarities and differences between different approaches. Classification of extraction techniques according to the mass transfer principles is provided.