Ammonium chloride salting out extraction/cleanup for trace-level quantitative analysis in food and biological matrices by flow injection tandem mass spectrometry

Flow-injection MS analysis as a simplified approach to pesticide screening in apples

A fast and simplified method based on mass spectrometry analysis was developed for pesticide qualification in apple peel. The main feature of the method is flow-injection of the loop pre-defined sample volume directly to the MS source, with no chromatographic separation. Method performances were evaluated for five pesticides regularly used in apple orchard treatments. First, primary features of the method such as the loop injection dynamics, total analysis time, chronogramic peaks integrity and sensitivity were evaluated. Then the applicability of the method for qualitative and quantitative screening was assessed on citrate buffered QuEChERS cleaned-up apple peel samples. The developed method offers a possibility for simplified, more economic high throughput screening for pesticides in apples. The method is intended to be a tool for preliminary qualitative assessment of pesticides residues in fruit. Quantitative features of the method are analyte and sample preparation dependent, most certainly due to the lack of chromatography.

A new sample preparation approach for the analysis of 98 current-use pesticides in soil and herbaceous vegetation using HPLC-MS/MS in combination with an acetonitrile-based extraction

A simple acetonitrile-based extraction method for the determination of 98 current-use pesticides (CUPs) in soil and herbaceous vegetation using HPLC-ESI-MS/MS is reported. The method was optimized in terms of extraction time, buffer (ammonium formate) ratio, and graphitized carbon black (GCB) ratio for the clean-up of vegetation. The validated method yielded accuracy in terms of percentage recovery of 71-125% (soil) and 70-117% (vegetation) for the majority of 98 CUPs. The precision in terms of relative standard deviation was at 1-14% (soil), and 1-13% (vegetation). Matrix-matched calibration curves exhibited good linearities (R² > 0.99). The limits of quantitation ranged between 0.008 and 21.5 μg kg^-1 in soil and vegetation. The reported method was applied to soils and vegetation from 13 agricultural sites across Germany. Overall, 44 of the 98 common CUPs were detected in our samples and the qualitative load is well above the average for arable soils in the EU.

Assessment and validation of the p-QuEChERS sample preparation methodology for the analysis of >200 veterinary drugs in various animal-based food matrices

The need remains for veterinary multi-residue methods that reliably quantify and identify veterinary drugs in the various animal-based food matrices. Such a method should not only show good method performance parameters (e.g. recoveries of analytes) but must also be fast and cheap. The proposed method focused on the following points: acceptable analyte trueness (recovery) and precision for a large number (200) of diverse veterinary drugs in the relevant animal-based food matrices (egg, muscle, fatty fish, liver, kidney, and honey). The sample preparation method termed p-QuEChERS uses a salt mixture consisting of potassium phosphates to induce phase separation. The avoidance of conventional QuEChERS salts (e.g. magnesium sulphate) significantly improves recoveries of several critical analytes. Analyte recoveries were further improved by adding a centrifugation and a defatting step before initiating the salt-induced phase separation. This combined clean-up removes a large fraction of the potentially interfering matrix compounds. As a result, matrix effects in the electrospray interface were minimized. These factors were the basis for the obtained good validation data. Two types of high-resolution mass spectrometers coupled to liquid chromatography were compared for analysis. In comparison with conventional QuEChERS, the proposed p-QuEChERS concept improved the recovery of polar analytes such as penicillins, tetracyclines and quinolones. The simplicity of the procedure and the low consumable expenses make the method ideal for the routine control of veterinary drugs in all evaluated animal-based food matrices.

Modulation of the peroxidase-like activity of iron oxide nanoparticles by surface functionalization with polysaccharides and its application for the detection of glutathione

Here, we employed three polysaccharides, such as dextran, hyaluronic acid, and chitosan, for surface modification of iron oxide nanoparticles (IONPs) and carried out in-depth investigation to elucidate the effect of surface functionalities on the peroxidase (POD) like activity of IONPs. The affinity of substrates to the catalytic site of IONPs was found to be determined by the surface functional groups and hydration layer of polysaccharide coating on the surface of IONPs. The role of hydration layer was further confirmed by the results that the POD-like activity of IONPs coated with a certain polysaccharide having higher water holding capacity was significantly enhanced by salting-out reagent, such as ammonium chloride that is known to reduce the thickness of hydration layer. Moreover, the excellent catalytic activity of dextran-coated IONPs was successfully applied to develop a highly sensitive sensing system for the detection of glutathione (GSH) with a limit of detection of 2.3 nM.

Wide-scope multi-residue analysis of pesticides in beef by ultra-high-performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry

Increasing pesticide contamination in foods of animal origin has made the wide-scope multi-residue analysis of pesticides an international concern. In this study, a sensitive and reliable multi-residue pesticide analysis method for beef was developed with the use of 129 pesticides to demonstrate the full scope of the method. The pesticides were extracted and purified using a modified QuEChERS technique and analysed using ultra-high-performance liquid chromatography coupled to quadrupole time-of-flight mass spectrometry. An orthogonal array design was employed for optimisation of the method, significantly scientising and simplifying the process. Method validation revealed satisfactory sensitivity with limits of quantification values ranging from 0.003 to 11.37 µg∙kg^-1. Matrix effects ranged from 83.85% to 120.66%. Recovery at three spiking levels (20, 50, and 100 µg∙kg^-1) were 70.51-128.12% and the intra-day and inter-day precisions were less than 20%, indicating good accuracy and precision.

Novel Salt-Assisted Liquid-Liquid Microextraction Technique for Environmental, Food, and Biological Samples Analysis Applications: A Review

Background::

Sample preparation has gained significant recognition in the chemical analysis workflow. Substantial efforts have been made to simplify the comprehensive process of sample preparation that is focused on green sample preparation methodology, including the miniaturization of extraction method, elimination of the sample pre-treatment as well as the post-treatment steps, elimination of toxic as well as hazardous organic solvent consumption, reduction in sample volume requirements, reducing the extraction time, maximization of the extraction efficiency and possible automation.

Methods::

Among various microextraction processes, liquid-phase microextraction (LPME) is most abundantly used in the extraction of the target analytes. The salting-out phenomenon has been introduced into the LPME procedure and has been raised as a new technique called the ‘Salt-Assisted Liquid-Liquid Microextraction (SALLME)’. The principle is based on decreasing the solubility of less polar solvent or analyte with an increase in the concentration of the salt in aqueous solution leading to two-phase separation.

Conclusion::

SALLME proved to be a simple, rapid, and cost-effective sample preparation technique for the efficient extraction and preconcentration of organic and inorganic contaminants from various sample matrices, including environmental, biological, and food samples. SALLME exhibits higher extraction efficiency and recovery and compatible with multiple analytical instruments. This review provides an overview of developments in SALLME technique and its applications to till date.

QuEChERS - Fundamentals, relevant improvements, applications and future trends

The Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method is a simple and straightforward extraction technique involving an initial partitioning followed by an extract clean-up using dispersive solid-phase extraction (d-SPE). Originally, the QuEChERS approach was developed for recovering pesticide residues from fruits and vegetables, but rapidly gained popularity in the comprehensive isolation of analytes from different matrices. According to PubMed, since its development in 2003 up to November 2018, about 1360 papers have been published reporting QuEChERS as extraction method. Several papers have reported different improvements and modifications to the original QuEChERS protocol to ensure more efficient extractions of pH-dependent analytes and to minimize the degradation of labile analytes. This analytical approach shows several advantages over traditional extraction techniques, requiring low sample and solvent volumes, as well as less time for sample preparation. Furthermore, most of the published studies show that the QuEChERS protocol provides higher recovery rate and a better analytical performance than conventional extraction procedures. This review proposes an updated overview of the most recent developments and applications of QuEChERS beyond its original application to pesticides, mycotoxins, veterinary drugs and pharmaceuticals, forensic analysis, drugs of abuse and environmental contaminants. Their pros and cons will be discussed, considering the factors influencing the extraction efficiency. Whenever possible, the performance of the QuEChERS is compared to other extraction approaches. In addition to the evolution of this technique, changes and improvements to the original method are discussed.

The determination of gemini surfactants used as gene delivery agents in cellular matrix using validated tandem mass spectrometric method

A simple, reliable flow injection analysis (FIA)-tandem mass spectrometric (MS/MS) method was developed for the determination of gemini surfactants, designated as 16-3-16, 16(Py)-S-2-S-(Py)16 and 16-7N(GK)-16, as gene delivery agents in cellular matrix. 16-3-16 is a conventional gemini surfactant bearing two quaternary amines, linked by a 3-carbon spacer region, 16(Py)-S-2-S-(Py)16 contains two pyridinium head groups, while 16-7N(GK)-16 bears a glycine-lysine di-peptide in the space region. The method was fully validated according to USFDA guidelines. It is the first time that FIA-MS/MS method was developed for the quantification of gemini surfactants, belonging to different structural families. The method was superior to existing liquid chromatographic (LC)-MS/MS methods in terms of sensitivity and time of analysis. Positive electrospray ionization (ESI) in the multiple reaction monitoring (MRM) mode were used on a triple quadrupole-linear ion trap (4000 QTRAP^®) instrument. Deuterated internal standards were used to correct for matrix effects and variations in ionization within the ESI source. Isotope dilution standard curves were established in cellular matrix, with a linear range of 10 nM-1000 nM for 16-3-16 and 16(Py)-S-2-S-(Py)16, and 20 nM-2000 nM for 16-7N(GK)-16. The precision, accuracy, recovery and stability were all within the acceptable ranges as per the USFDA guidelines. The method was successfully applied for the quantification of target gemini surfactants in the nuclear fraction of PAM 212 keratinocyte cells treated with nanoparticles, which varied significantly and may explain differences in the observed efficiency and/or toxicity of these gemini surfactants in gene delivery.

Multiresidue Method for Quantification of Sulfonamides and Trimethoprim in Tilapia Fillet by Liquid Chromatography Coupled to Quadrupole Time-of-Flight Mass Spectrometry Using QuEChERS for Sample Preparation

A multiresidue method for detecting and quantifying sulfonamides (sulfapyridine, sulfamerazine, sulfathiazole, sulfamethazine, sulfadimethoxine, sulfamethoxazole, and sulfamethoxypyridazine) and trimethoprim in tilapia fillet (Oreochromis niloticus) using liquid chromatography coupled to mass spectrometry was developed and validated. The sample preparation was optimized using the QuEChERS approach. The chromatographic separation was performed using a C18 column and 0.1% formic acid in water and acetonitrile as the mobile phase in the isocratic elution mode. Method validation was performed based on the Commission Decision 2002/657/EC and Brazilian guideline. The validation parameters evaluated were linearity (r ≥ 0.99); limits of detection (LOD) and quantification (LOQ), 1 ng·g^-1 and 5 ng·g^-1, respectively; intraday and interdays precision (CV lower than 19.4%). The decision limit (CCα 102.6-120.0 ng·g^-1 and 70 ng·g^-1 for sulfonamides and trimethoprim, respectively) and detection capability (CCβ 111.7-140.1 ng·g^-1 and 89.9 ng·g^-1 for sulfonamides and trimethoprim, respectively) were determined. Analyses of tilapia fillet samples from fish exposed to sulfamethazine through feed (incurred samples) were conducted in order to evaluate the method. This new method was demonstrated to be fast, sensitive, and suitable for monitoring sulfonamides and trimethoprim in tilapia fillet in health surveillance programs, as well as to be used in pharmacokinetics and residue depletion studies.

Emerging flow injection mass spectrometry methods for high-throughput quantitative analysis

Where does flow injection analysis mass spectrometry (FIA-MS) stand relative to ambient mass spectrometry (MS) and chromatography-MS? Improvements in FIA-MS methods have resulted in fast-expanding uses of this technique. Key advantages of FIA-MS over chromatography-MS are fast analysis (typical run time <60 s) and method simplicity, and FIA-MS offers high-throughput without compromising sensitivity, precision and accuracy as much as ambient MS techniques. Consequently, FIA-MS is increasingly becoming recognized as a suitable technique for applications where quantitative screening of chemicals needs to be performed rapidly and reliably. The FIA-MS methods discussed herein have demonstrated quantitation of diverse analytes, including pharmaceuticals, pesticides, environmental contaminants, and endogenous compounds, at levels ranging from parts-per-billion (ppb) to parts-per-million (ppm) in very complex matrices (such as blood, urine, and a variety of foods of plant and animal origin), allowing successful applications of the technique in clinical diagnostics, metabolomics, environmental sciences, toxicology, and detection of adulterated/counterfeited goods. The recent boom in applications of FIA-MS for high-throughput quantitative analysis has been driven in part by (1) the continuous improvements in sensitivity and selectivity of MS instrumentation, (2) the introduction of novel sample preparation procedures compatible with standalone mass spectrometric analysis such as salting out assisted liquid-liquid extraction (SALLE) with volatile solutes and NH4(+) QuEChERS, and (3) the need to improve efficiency of laboratories to satisfy increasing analytical demand while lowering operational cost. The advantages and drawbacks of quantitative analysis by FIA-MS are discussed in comparison to chromatography-MS and ambient MS (e.g., DESI, LAESI, DART). Generally, FIA-MS sits 'in the middle' between ambient MS and chromatography-MS, offering a balance between analytical capability and sample analysis throughput suitable for broad applications in life sciences, agricultural chemistry, consumer safety, and beyond.

Analysis of Nitrosamines in Cooked Bacon by QuEChERS Sample Preparation and Gas Chromatography-Tandem Mass Spectrometry with Backflushing

Nitrites are added as a preservative to a variety of cured meats, including bacon, to kill bacteria, extend shelf life, and improve quality. During cooking, nitrites in the meat can be converted to carcinogenic nitrosamines (NAs), the formation of which is mitigated by the addition of antioxidants. In the past, the U.S. Department of Agriculture (USDA) Food Safety and Inspection Service (FSIS) monitored NAs in pan-fried bacon, but FSIS terminated monitoring of NAs in the 1990s due to the very low levels found. FSIS recently chose to conduct a risk assessment of NAs in cooked bacon to determine if current levels warrant routine monitoring of NAs again. To meet FSIS needs, we developed, validated, and implemented a new method of sample preparation and analysis to test cooked bacon for five NAs of most concern, which consist of N-nitroso-dimethylamine, -diethylamine, -dibutylamine, -piperidine, and -pyrrolidine. Sample preparation was based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) approach and analysis by gas chromatography-tandem mass spectrometry. Ruggedness was improved markedly in the analysis of the complex fatty extracts by backflushing the guard column, injection liner, and half of the analytical column after every injection. Validation results were acceptable with recoveries of 70-120% and <20% RSDs for the five NAs, with a reporting limit of 0.1 ng/g. NA concentrations in 48 samples were all <15 ng/g, with most <1 ng/g and many <0.1 ng/g. Also, microwave cooking of bacon gave slightly lower concentrations overall compared to pan-frying.

Electron ionization LC-MS with supersonic molecular beams--the new concept, benefits and applications

A new type of electron ionization LC-MS with supersonic molecular beams (EI-LC-MS with SMB) is described. This system and its operational methods are based on pneumatic spray formation of the LC liquid flow in a heated spray vaporization chamber, full sample thermal vaporization and subsequent electron ionization of vibrationally cold molecules in supersonic molecular beams. The vaporized sample compounds are transferred into a supersonic nozzle via a flow restrictor capillary. Consequently, while the pneumatic spray is formed and vaporized at above atmospheric pressure the supersonic nozzle backing pressure is about 0.15 Bar for the formation of supersonic molecular beams with vibrationally cold sample molecules without cluster formation with the solvent vapor. The sample compounds are ionized in a fly-though EI ion source as vibrationally cold molecules in the SMB, resulting in 'Cold EI' (EI of vibrationally cold molecules) mass spectra that exhibit the standard EI fragments combined with enhanced molecular ions. We evaluated the EI-LC-MS with SMB system and demonstrated its effectiveness in NIST library sample identification which is complemented with the availability of enhanced molecular ions. The EI-LC-MS with SMB system is characterized by linear response of five orders of magnitude and uniform compound independent response including for non-polar compounds. This feature improves sample quantitation that can be approximated without compound specific calibration. Cold EI, like EI, is free from ion suppression and/or enhancement effects (that plague ESI and/or APCI) which facilitate faster LC separation because full separation is not essential. The absence of ion suppression effects enables the exploration of fast flow injection MS-MS as an alternative to lengthy LC-MS analysis. These features are demonstrated in a few examples, and the analysis of the main ingredients of Cannabis on a few Cannabis flower extracts is demonstrated. Finally, the advantages of EI-LC-MS with SMB are listed and discussed.

Recent advances in salt-assisted LLE for analyzing biological samples

Salt-assisted LLE (SALLE) has been attracting growing interest in bioanalysis. The technique is particularly advantageous due to its simple and fast experimental execution using conventional laboratory equipment. Besides, SALLE uses water-miscible organic solvents making the extracts readily compatible with various analytical separation and detection techniques. This article presents a brief overview of the extraction technique and its role in bioanalysis. Some of the most relevant achievements on SALLE application to biological samples are discussed - namely the study of the main extraction parameters, the combination with other extraction techniques and the instrumental analysis of the extracts. Developments on automation, miniaturization and microextraction for SALLE procedures are also discussed as a perspective for future applications even more attractive for the analysis of biological samples.

Use of ammonium formate in QuEChERS for high-throughput analysis of pesticides in food by fast, low-pressure gas chromatography and liquid chromatography tandem mass spectrometry

The "quick, easy, cheap, effective, rugged, and safe" (QuEChERS) approach to sample preparation is widely applied in pesticide residue analysis, but the use of magnesium sulfate and other nonvolatile compounds for salting out in the method is not ideal for mass spectrometry. In this study, we developed and evaluated three new different versions of the QuEChERS method using more volatile salts (ammonium chloride and ammonium formate and acetate buffers) to induce phase separation and extraction of 43 representative pesticide analytes of different classes. Fast low-pressure gas chromatography tandem mass spectrometry (LPGC-MS/MS) and liquid chromatography (LC)-MS/MS were used for analysis. The QuEChERS AOAC Official Method 2007.01 was also tested for comparison purposes. Of the studied methods, formate buffering using 7.5g of ammonium formate and 15mL of 5% (v/v) formic acid in acetonitrile for the extraction of 15g of sample (5g for wheat grain) provided the best performance and practical considerations. Method validation was carried out with and without the use of dispersive solid-phase extraction for cleanup, and no significant differences were observed for the majority of pesticides. The method was demonstrated in quantitative analysis for GC- and LC-amenable pesticides in 4 representative food matrices (apple, lemon, lettuce, and wheat grain). With the typical exceptions of certain pH-dependent and labile pesticides, 90-110% recoveries and <10% RSD were obtained. Detection limits were mostly <5ng/g, which met the general need to determine pesticide concentrations as low as 10ng/g for monitoring purposes in food applications.

Simultaneous determination of dorzolomide and timolol in aqueous humor: a novel salting out liquid-liquid microextraction combined with HPLC

A Snovel method for the simultaneous separation and determination of two antiglaucoma drugs namely, dorzolamide hydrochloride (DOR) and timolol maleate (TIM) in aqueous humor samples (AH) was developed by using salting-out assisted liquid-liquid microextraction (SALLME) combined with HPLC-UV method. Box-Behnken experimental design and response surface methodology were employed to assist the optimization of SALLME conditions, including salt concentration, the pH of sample solution and vortex time as variable factors. The optimal extraction conditions were as follows: to 50 µL of AH sample, 100 µL of phosphate buffer (100 mmol L(-1), pH 11.9), 90 µL of acetonitrile (ACN) and 0.11 g of (NH4)2SO4 salt were added into an Eppendorf vial (1 mL) then vortexed for 1.1 min. As an effort to miniaturize SALLE system, a 1 mL syringe adapted with a capillary tube was employed as the phase separation device. Once the phase separation occurred, the upper layer could be narrowed into the capillary tube by pushing the plunger; thus, the collection of the upper layer solvent was simple and convenient. By miniaturization, the consumption of the organic solvent was decreased as low as possible. The chromatographic separation was achieved on Gemini C18 column using a mobile phase of ACN: 30 mmol L(-1) potassium dihydrogen phosphate buffer containing 0.1% triethylamine, pH 3.5 (20:80, v/v) at a flow rate of 1 mL min(-1) and UV detection at 254 and 295 nm for DOR and TIM, respectively. Mepivacaine hydrochloride was used as an internal standard. The described method showed better separation with enhanced sensitivities than the previously reported methods with limits of quantitation of 8.75 and 10.32 ng mL(-1) in aqueous solution and 15.97 and 23.53 ng mL(-1) in AH for DOR and TIM, respectively. The simple, rapid and eco-friendly SALLME-HPLC method has been successfully applied for the simultaneous pharmacokinetic studies of DOR and TIM in rabbit AH.

Biological sample preparation: attempts on productivity increasing in bioanalysis

Sample preparation is an important step of any biomedical analysis. Development and validation of fast, reproducible and reliable sample preparation methods would be very helpful in increasing productivity. Except for a few direct injection methods, almost all biological samples should at least be diluted before any analysis. Sometimes dilution is not possible because of the low concentration of the target analyte in the sample, and alternative pretreatments, such as filtration, precipitation and sample clean up using different extraction methods, are needed. This review focuses on the recent achievements in the pretreatment of biological samples and investigates them in six categories (i.e., dilution, filtration/dialysis, precipitation, extraction [solid-phase extraction, liquid–liquid extraction], novel techniques [turbulent flow chromatography, immunoaffinity method, electromembrane extraction] and combined methods). Each category will be discussed according to its productivity rate and suitability for routine analysis, and the discussed methods will be compared according to the mentioned indices.