In-field determination of trace dissolved manganese in estuarine and coastal waters with automatic on-line preconcentration and flame atomic fluorescence spectrometry

Eu(III) Functionalized Crystalline Polyimide Hydrogel Film as a Multifunctional Platform for Consecutive Sensing of Spermine and Copper Ions

In this study, a novel Eu(III) functionalized crystalline polyimide hydrogel film (Eu-1) is fabricated by incorporating highly stable polyimide (PI) into a sodium alginate (SA) matrix, followed by cross-linking reaction with Eu³⁺ ions. Based on different fluorescence responses, Eu-1 is used for the consecutive detection of spermine (Spm) and copper ions (Cu²⁺). Eu-1 can be employed as a sensor for polyamine, especially for Spm with significant fluorescence enhancement based on the "turn on" mode. The fluorescent sensor Eu-1@Spm constructed by the Eu-1 and Spm can be further used as a "turn off" sensor to quantitatively monitor Cu²⁺. The good selectivity combined with the low detection limit of the sensor meets the requirements for monitoring Cu²⁺. The possible luminescence response mechanisms to Spm and Cu²⁺ have been studied through experimental data and theoretical calculations. In addition, a back-propagation neural network (BPNN) model based on an Eu-1@Spm sensor is constructed, which can accurately distinguish Cu²⁺ concentrations by deep machine learning (ML). This work not only puts forward a facile method to prepare a novel Eu-functionalized PI-based hybrid film but also demonstrates the potential of PI-based film materials for fluorescence detection.

Improving the measurement of total dissolved sulfide in natural waters: A new on-site flow injection analysis method

Total dissolved sulfide (TDS) plays multiple important roles in the aquatic environments. However, the determination of trace levels of TDS in natural waters is challenging because TDS is vulnerable to oxidation and volatilization. In this study, a fully automated flow injection analysis spectrophotometric system, incorporating a hollow fiber membrane contactor (HFMC) and a long path length liquid waveguide capillary cell, was fabricated to facilitate the on-site measurement of trace TDS in natural waters. The HFMC was used for matrix separation and analyte preconcentration. The measurement was based on the reaction of sulfide and N,N-dimethyl-p-phenylenediamine in the presence of FeCl₃ under acidic conditions to yield methylene blue (MB). The proposed method was highly sensitive, with detection and quantification limits of 0.57 and 1.90 nmol L^-1, respectively. The linear working range was from 1.90 to 150 nmol L^-1, with a correlation coefficient of 0.9995. The repeatability, expressed as the relative standard deviation, was less than 0.86% (n = 15) and the recoveries varied from 76.2 ± 0.1% to 103.9 ± 0.6% (n = 3) for spiked samples. This method was applied to conduct a field analysis of TDS in a reservoir, giving results aligned with those obtained using a standard MB method. This work demonstrates that the new method for determining TDS was effective for both laboratory analysis and on-site measurement.

Spectrophotometric flow injection determination of dissolved titanium in seawater exploiting in-line nitrilotriacetic acid resin preconcentration and a long path length liquid waveguide capillary cell

A sensitive spectrophotometric method for the determination of dissolved titanium (Ti) in seawater is developed. It involves in-line preconcentration and a long path length liquid waveguide capillary cell (LWCC). Nitrilotriacetic acid (NTA) resin is used to preconcentrate Ti from ∼25 mL seawater sample at pH 1.7, and elution is accomplished with 0.8 mol L^-1 hydrochloride acid. The eluted Ti solution is buffered to pH 6.0 with 1.0 mol L^-1 ammonium acetate and mixed with 1.5 mmol L^-1 Tiron solution. The mixture is then injected into LWCC and measured by spectrophotometry at 420 nm. Before the preconcentration step, the sample is treated with 7 mmol L^-1 ascorbic acid to reduce Fe(III) to Fe(II), in order to eliminate the Fe interference. The method is not interfered by Fe(III) and Cu(II) present in seawater samples at concentrations 50-fold higher in relation to Ti, and by Cd(II), Pb(II), Cr(VI), Mn(II), Al(III), Zn(II), and Ni(II) at concentrations 100-fold higher in relation to Ti. It is time efficient (7.5 minutes per sample), sensitive (0.10 nmol L^-1 detection limit), precise (1.40% measurement RSD at 1.00 nmol L^-1 Ti) and is characterized by a linear range of 0.50-5.00 nmol L^-1 Ti. The method was applied to analysis of natural water samples collected from the Jiulongjiang Estuary, Fujian, China.