Nanofiber polymers as novel sorbents for on-line solid phase extraction in chromatographic system: A comparison with monolithic reversed phase C18 sorbent

Low flow-resistance solid phase extraction of fluoroquinolones in water and food samples by high-pressure wet spinning porous polyimide microfibers

In this work, porous polyimide microfibers (PI-μF) were prepared by high-pressure wet spinning method, and successfully applied as adsorbents for solid phase extraction (SPE) of fluoroquinolones (FQs) in water and food samples. The PI-μFs of ∼10, 25, 50, 100 μm in diameter could be controlled by the inner diameter of quartz capillary nozzles. The flow resistance of SPE cartridges packed with 10 μm PI microfiber (10-PI-μF) and 25-PI-μF was comparable to or even lower than that of commercial SPE cartridges, while the flow resistance of 50-PI-μF and 100-PI-μF SPE cartridges was increased obviously due to tiny broken pieces. The 10-PI-μF and 25-PI-μF have a specific surface area of 102 m2 g-1 and 76 m2 g-1, mesopores of 22-32 nm, and large breakthrough volume of 110 mL/5 mg and 85 mL/5 mg for FQs, while the 50-PI-μF and 100-PI-μF had much lower specific surface area and hardly had retention for FQs. FQs from tap water, egg and milk samples were then extracted by PI-μF SPE, and analyzed by high performance liquid chromatography-fluorescence detector (HPLC-FLD). SPE parameters as type of elution solvent, elution solvent volume, pH value of sample solution, flow rate of sample solution, and breakthrough volume were first optimized in detail. Under the optimal conditions, the PI-μF SPE/HPLC-FLD method showed high recoveries (96.8%-107%), wide linearity (0.05-50 μg L-1, or 0.01-10 μg L-1), high determination coefficients (R2 ≥0.9992), and low limits of detection (LODs, 0.005-0.014 μg L-1). For the real tap water, egg and milk samples, the recoveries and RSDs were 81-119% and 0.8-9.8%, respectively. The results show that porous microfiber up to 25 μm in diameter is a promising solid-phase extraction adsorbent with the lowest flow resistance that can be used for trace organic pollutants in water and food samples.

Composite Nanofibers as Novel Sorbents for On-Line and Off-Line Solid-Phase Extraction in Chromatographic System: A Comparison for Detection of Free Biogenic Monoamines and Their Metabolites in Plasma

Two different pretreatment approaches have been used for the enrichment and separation of biogenic monoamines and metabolites in plasma for high performance liquid chromatography (HPLC) determination. The first approach, based on on-line packed-fiber solid-phase extraction (PFSPE) coupled with HPLC, allows for the simultaneous detection of epinephrine (E), norepinephrine (NE), dopamine (DA), 3-methoxyl epinephrine (MN), norepinephrine (NMN), 3-methoxytyramine (3-MT), and 5-hydroxytryptamin (5-HT). Using this developed on-line PFSPE–HPLC method, the limit of detections (LODs) of the seven analytes ranged from 1 ng/mL (NMN and MN) to 2 ng/mL (NE, E, DA, 3-MT and 5-HT). The reportable ranges were 5–300 ng/mL for NE and DA, 5–100 ng/mL for E, and 5–200 ng/mL for NMN, MN, 3-MT and 5-HT. The off-line PFSPE–HPLC was employed in the second approach and could provide simultaneous detection of NE, E, DA, NMN, and MN. The linearity was verified in the range of 0.5–20 ng/mL (NE, E, and DA) and 20–250 ng/mL (NMN and MN). The LODs of the five analytes ranged from 0.2 ng/mL (NE, E, and DA) to 5 ng/mL (NMN and MN). This study verified the possibility of using nanofibers as an adsorbent in an on-line PFSPE–HPLC system for the determination of biogenic monoamines and their metabolites in human plasma. Compared with the off-line PFSPE approach, the on-line PFSPE method deserves attention mainly due to its greener character, derived from the automation of the process and high-throughput with less operators’ handling.

Nanofibrous Online Solid-Phase Extraction Coupled with Liquid Chromatography for the Determination of Neonicotinoid Pesticides in River Waters

Polymeric nano- and microfibers were tested as potential sorbents for the extraction of five neonicotinoids from natural waters. Nanofibrous mats were prepared from polycaprolactone, polyvinylidene fluoride, polystyrene, polyamide 6, polyacrylonitrile, and polyimide, as well as microfibers of polyethylene, a polycaprolactone nano- and microfiber conjugate, and polycaprolactone microfibers combined with polyvinylidene fluoride nanofibers. Polyimide nanofibers were selected as the most suitable sorbent for these analytes and the matrix. A Lab-In-Syringe system enabled automated preconcentration via online SPE of large sample volumes at low pressure with analyte separation by HPLC. Several mat layers were housed in a solvent filter holder integrated into the injection loop of an HPLC system. After loading 2 mL sample on the sorbent, the mobile phase eluted the retained analytes onto the chromatographic column. Extraction efficiencies of 68.8–83.4% were achieved. Large preconcentration factors ranging from 70 to 82 allowed reaching LOD and LOQ values of 0.4 to 1.7 and 1.2 to 5.5 µg·L⁻¹, respectively. Analyte recoveries from spiked river waters ranged from 53.8% to 113.3% at the 5 µg·L⁻¹ level and from 62.8% to 119.8% at the 20 µg·L⁻¹ level. The developed methodology proved suitable for the determination of thiamethoxam, clothianidin, imidacloprid, and thiacloprid, whereas matrix peak overlapping inhibited quantification of acetamiprid.

Polyamide Noncoated Device for Adsorption-Based Microextraction and Novel 3D Printed Thin-Film Microextraction Supports

Polyamide noncoated device for adsorption-based microextraction (PANDA microextraction) is a brand new, easy to prepare, environmentally friendly, inexpensive, and efficient sample preparation method created entirely with the use of 3D printing. The proposed method is based on the extractive proprieties of the unmodified polyamide and carbon fiber blends and is compared with the highly selective thin-film microextraction (TFME). In addition, 3D printing was used to simplify the process of TFME. Prototype sample preparation devices were evaluated by the extraction of oral fluid spiked with 38 small molecules with diverse chemical natures, such as lipophilicity in the log P range of 0.2–7.2. The samples were analyzed by high-performance liquid chromatography coupled with tandem mass spectrometry. The results indicate that chemically and thermally resistant 3D printed supports can be successfully used as a cost-saving, environmentally friendly solution for the preparation of TFME devices, alternative to the conventional metal supports, with only marginal differences in the extraction yield (mean = 4.0%, median = 1.8%, range = 0.0–22.3%, n = 38). Even more remarkably, in some cases, the newly proposed PANDA microextraction method exceeded the reference TFME in terms of the extraction efficacy and offered excellent sample cleanup as favorable matrix effects were observed (mean = −8.5%, median = 7.5%, range = −34.7–20.0%, n = 20). This innovative approach paves the road to the simplified sample preparation with the use of emerging extractive 3D printing polymers.

Poly-ε-caprolactone Nanofibrous Polymers: A Simple Alternative to Restricted Access Media for Extraction of Small Molecules from Biological Matrixes

Poly-ε-caprolactone nanofibrous polymer has been used as an alternative to restricted access media for extraction of protein-containing biological samples and direct transfer in the chromatographic system. Three commercial cartridges differing in length and internal diameter have been manually packed with the composite material prepared from poly-ε-caprolactone nanofibers coated on poly-ε-caprolactone microfibrous scaffold and connected to the column-switching chromatographic system. Bovine milk and human serum (25 μL) spiked with a mixture of methyl-, ethyl-, propyl-, and butylparaben in a concentration range of 1-100 μg mL^-1 were online extracted using the cartridge-containing fibers. Then, 5 and 20% (v/v) aqueous methanol was applied as the washing mobile phase. While the ballast protein macromolecules were quantitatively eluted from the nano/microfibrous composite sorbent, the parabens were retained. After the mobile phase was switched to a stronger one, these compounds were then eluted from the extraction sorbent, directed in the analytical column, and finally separated. An extraction efficiency of 86-101% for all parabens achieved using the optimum-sized cartridge and a repeatability of the extraction procedure of 0.06-1.95% RSD were obtained.

Nanofibers as advanced sorbents for on-line solid phase extraction in liquid chromatography: A tutorial

Polymers in nanofiber format promise a great potential as sorbents for extraction techniques. This tutorial provides an overview of direct coupling of extraction techniques based on nanofibers to liquid chromatography. Arrangements of the fibers in conventional extraction cartridges are demonstrated. Selection of suitable nanomaterials according to their surface density, wettability, and mechanical stability is proposed and personal experience of the authors commented. Optimization of on-line extraction procedure, practical aspects, technical problems, pitfalls, pros, and cons of using nanofibers for extraction in high-pressure chromatography systems are also discussed and several examples presented. The following text comprehensively summarizes numerous reports that dealt with the topic. Future perspectives of advanced nanofiber materials and approaches that concern polymer fibers modifications are also included.

Polyethylene Terephthalate Nanofiber Sheet as the Novel Extraction Medium for the Determination of Phthalates in Water Samples

A novel extraction medium was developed by packing polyethylene terephthalate (PET) nanofiber sheet having a diameter of 500 nm into a stainless-steel capillary of 0.8 mm inner diameter. The nanofiber was prepared by a carbon dioxide (CO₂) laser supersonic multi-drawing method, which has a significantly higher surface area than the original PET fiber. A nanofiber sheet was prepared by winding the nanofibers. Extraction of phthalates in water samples by a PET nanofiber-packed extraction capillary was investigated using a conventional high-performance liquid chromatography (HPLC). Water samples were introduced into the extraction capillary with a low pressure. After extracting the water sample, the extraction capillary was directly connected to a six-port valve of HPLC with a PEEK nut, and the extracted analytes were desorbed, followed by injection to an HPLC system using a small amount of organic solvent. In this manuscript, the fundamental performance of the nanofiber sheet-packed extraction capillary for the extraction of organic compounds in water samples is quantitatively evaluated using a conventional HPLC system.

Evaluation of the tubing material and physical dimensions on the performance of extraction columns for on-line sample preparation-LC-MS/MS

Nowadays, high analytical throughputs are required considering an increasing demand for faster, simple and improved methods to analyze contaminants in a considerable number of samples. Generally, these compounds are present in complex matrices in contact with a high number of interferents becoming their determination difficult at low concentration. In this context, on-line extraction techniques arose to improve the extraction as well as separation power, while minimizing errors related to human sample manipulation. This paper describes a study regarding the development and optimization of columns used as an extraction device in multidimensional liquid chromatography. The main goals were the evaluation of the material used as column body as well as the investigation of the tube dimensions (internal diameter and length) in the extraction performance. Firstly, several tube materials were tested (steel, fused silica, PEEK, among others) being steel whose reported the best performance and was consequently chose for further studies. The investigation about the effects of the columns physical dimensions revealed a linear relationship between performance and the amount of sorbent utilized as extractive phase. However, when different columns with same amount of sorbent were tested results suggests that both i.d. and lengths play an important role in extraction efficiency. The longest columns with lower internal diameter showed the best results favoring the radial as well as axial analytes diffusion into the extraction column. After evaluation of these column variables, applications were carried out employing several different analytes belonging to various chemical classes and practical utilization, in order to reinforce the versatility as well as the robustness of this proposed study.

Current Trends in Fully Automated On-Line Analytical Techniques for Beverage Analysis

The determination of target analytes in complex matrices such as beverages requires a series of analytical steps to obtain a reliable analysis. This critical review presents the current trends in sample preparation techniques based on solid phase extraction miniaturization, automation and on-line coupling. Techniques discussed include solid-phase extraction (SPE), solid-phase microextraction (SPME), in-tube solid-phase microextraction (in-tube SPME) and turbulent-flow chromatography (TFC). Advantages and limitations, as well as several of their main applications in beverage samples are discussed. Finally, fully automated on-line systems that involve extraction, chromatographic separation, and tandem mass spectrometry in one-step are introduced and critically reviewed.

Screening of extraction properties of nanofibers in a sequential injection analysis system using a 3D printed device

A novel application of the three-dimensional printing technology for the automation of solid phase extraction procedures in a low-pressure sequential injection analysis system is presented. A 3D printed device was used as a housing for nanofiber membranes in solid phase extraction. The applicability of the device is demonstrated with the extraction of substances of various physical-chemical properties. Pharmaceuticals including non-steroidal anti-inflammatory drugs, antihistaminics, and steroidal structures, as well as emerging pollutants such as bisphenols and pesticide metsulfuron methyl were used as model analytes to study the extraction performance of the nanofibers. Six different nanofiber types comprising polyamide, polyethylene, polyvinylidene fluoride, polycaprolactone combined with polyvinylidene fluoride, and polyacrylonitrile, produced by electrospinning were tested in solid phase extraction. The suitability of specific nanofibers for particular analytes is demonstrated.