Production of ultra-fine bioresorbable carbonated hydroxyapatite

Synthesis and characterization of hydroxyapatite self-assembled nanocomposites on graphene oxide sheets from seashell waste: A green process for regenerative medicine

Bone transplantation is the second most common transplantation surgery in the world. Therefore, there is an urgent need for artificial bone transplantation to repair bone defects. In bone tissue engineering, hydroxyapatite (HA) plays a major role in bone graft applications. This study deals with a facile method for synthesizing HA hexagonal nanorods from seashells by a solid-state hydrothermal transition process. The synthesized HA nanorods (∼2.29 nm) were reinforced with carbon nanotube and chitosan on graphene oxide sheets with polymeric support by in-situ synthetic approach. Among the synthesized nanocomposites viz., hydroxyapatite-graphene oxide (HA-GO), hydroxyapatite-graphene oxide-chitosan (HA-GO-CS), hydroxyapatite-graphene oxide-chitosan-carbon nanotube-polylactic acid (HA-GO-CS-CNT-PLA). Among them, the HA-GO-CS-CNT-PLA composite exhibits micro and macro porosity (∼200 to 600 μm), higher mechanical strength, (Hardness ∼90.5 ± 1.33 MPa; Tensile strength 25.62 MPa), and maximum cell viability in MG63 osteoblast-like cells (80%). The self-assembled hybrid-nanocomposite of HA-GO-CS-CNT-PLA is a promising material for bone filler application and could efficiently utilize seashell waste through the green process.

Hydroxyapatite Nanorods Based Drug Delivery Systems for Bumetanide and Meloxicam, Poorly Water Soluble Active Principles

Poorly water-soluble drugs represent a challenge for the pharmaceutical industry because it is necessary to find properly tuned and efficient systems for their release. In this framework, organic-inorganic hybrid systems could represent a promising strategy. A largely diffused inorganic host is hydroxyapatite (HAP, Ca10(PO4)6(OH)2), which is easily synthesized with different external forms and can adsorb different kinds of molecules, thereby allowing rapid drug release. Hybrid nanocomposites of HAP nanorods, obtained through hydrothermal synthesis, were prepared with two model pharmaceutical molecules characterized by low and pH-dependent solubility: meloxicam, a non-steroidal anti-inflammatory drug, and bumetanide, a diuretic drug. Both hybrids were physically and chemically characterized through the combined use of X-ray powder diffraction, scanning electron microscopy with energy-dispersive spectroscopy, differential scanning calorimetry, and infrared spectroscopy measurements. Then, their dissolution profiles and hydrophilicity (contact angles) in different media as well as their solubility were determined and compared to the pure drugs. This hybrid system seems particularly suitable as a drug carrier for bumetanide, as it shows higher drug loading and good dissolution profiles, while is less suitable for meloxicam, an acid molecule.

Synthesis and in vitro characteristics of biogenic-derived hydroxyapatite for bone remodeling applications

The inorganic component of bone matrix, hydroxyapatite (HAp) (with formula Ca10(PO4)6(OH)2), can be obtained from inexpensive waste resources that serve as excellent calcium precursors. In the present study, HAp nano-powder was synthesized from eggshells (ES) and crab shells (CS) by wet chemical precipitation method. Also, a hybrid sample was considered which is a mixture of HAp nano-powder synthesized from eggshells (25%) and crab shells (75%) (EC). The presence of phosphate, carbonate, and hydroxyl groups in the synthesized powder was confirmed through FTIR analysis. The phase composition was determined using XRD, and elemental analysis revealed a Ca/P ratio ranging from 1.5 to 1.8, confirming the HAp nature of the nano-powder, which ranged in size from 73 to 375 nm. Importantly, preliminary in vitro tests were conducted using mouse preosteoblast cell line MC3T3-E1 to evaluate the cytotoxic effects of the synthesized HAp. The results indicated excellent biocompatibility. Moreover, sample EC exhibited a significantly higher proliferation on days 3, 6, 9, and 12. EC demonstrated promising antimicrobial properties by exhibiting a significantly higher inhibitory effect against the bacteria Streptococcus mutans and Escherichia coli, and the fungi Candida albicans and Aspergillus niger. Additionally, EC displayed notable antioxidant activity, with IC50 values of 271.543 µg/ml and 407.764 µg/ml in DPPH and H2O2 assays, respectively. Furthermore, it showed strong anti-inflammatory properties, with a dose-dependent inhibition against protein denaturation. Given these findings, the synthesized HAp holds promise as a potential bone filler and could be beneficial for bone remodeling applications.

Synthesis and Characterization of Nano-Hydroxyapatite Obtained from Eggshell via the Hydrothermal Process and the Precipitation Method

Hydroxyapatite (HA) is a major component of the inorganic minerals in the hard tissues of humans and has been widely used as a biomedical ceramic material in orthopedic and dentistry applications. Because human bone contains several impurities, including carbonates, chlorides, fluorides, magnesium, and strontium, human bone minerals differ from stoichiometric HA. Additionally, natural bone is composed of nano-sized HA, and the nanoscale particles exhibit a high level of biological activity. In this paper, HA is prepared via the hydrothermal process because its reaction conditions are easy to control and it has been shown to be quite feasible for large-scale production. Therefore, the hydrothermal process is an effective and convenient method for the preparation of HA. Furthermore, eggshell is adopted as a source of calcium, and mulberry leaf extract is selectively added to synthesize HA. The eggshell accounts for 11% of the total weight of a whole egg, and it consists of calcium carbonate, calcium phosphate, magnesium carbonate, and organic matter. Eggshell contains a variety of trace elements, such as magnesium and strontium, making the composition of the synthesized HA similar to that of the human skeleton. These trace elements exert considerable benefits for bone growth. Moreover, the use of eggshell as a raw material can permit the recycling of biowaste and a reduction in process costs. The purpose of this study is to prepare HA powder via the hydrothermal method and to explore the effects of hydrothermal conditions on the structure and properties of the synthesized HA. The room-temperature precipitation method is used for the control group. Furthermore, the results of an immersion test in simulated body fluid confirm that the as-prepared HA exhibits good apatite-forming bioactivity, which is an essential requirement for artificial materials to bond to living bones in the living body and promote bone regeneration. In particular, it is confirmed that the HA synthesized with the addition of the mulberry leaf extract exhibits good in vitro biocompatibility. The morphology, crystallite size, and composition of the carbonated nano-HA obtained herein are similar to those of natural bones. The carbonated nano-HA appears to be an excellent material for bioresorbable bone substitutes or drug delivery. Therefore, the nano-HA powder prepared in this study has great potential in biomedical applications.

Synthesis of Ti6Al4V/SrFHA Composites by Microwave-Assisted Liquid Phase Deposition and Calcination

The feasibility of synthesis of Ti6Al4V/SrFHA (Ca9.37Sr0.63(PO4)6F2) composites via coating strontium and fluorine co-doped HA to Ti6Al4V substrate by microwave-assisted liquid phase deposition and calcination was evaluated, with a focus on the effect of the deposition temperature from 30 °C to 70 °C. The outcomes demonstrate that strontium and fluorine can be successfully doped into HA to form a SrFHA coating with modified micromorphology which is deposited on the alloy. When the deposition temperature was 50 °C, the coating with the largest uniform continuous SrFHA coverage was obtained. After calcination, the adhesion strength and Vickers microhardness of the Ti6Al4V/SrFHA composite increased from 0.68 MPa and 323 HV to 2.41 MPa and 329 HV, respectively, with a decrease in the water contact angle from 10.88° to 7.24°, exhibiting enhancement of both mechanical properties and wettability. Moreover, the composite obtained at the deposition temperature of 50 °C exhibited good bioactivity based on the simulate body fluid (SBF) test. On account of the above features primarily as a result of the combined effect of the co-doping of strontium and fluorine, high crystallinity of SrFHA, large surface roughness, and formation of the titanium oxide transition layer, the Ti6Al4V/SrFHA composite shows great potential in dental implantology.

Green Synthesis of Bioactive Hydroxyapatite/Cellulose Composites from Food Industrial Wastes

This work aimed at conversion of worthless indurtial wastes to valuable product. Herein, bioactive composites based on bacterial cellulose (BC) and eggshell or eggshell-derived hydroxyapatite (HAp) were prepared by a green method using Gluconacetobacter xylinum bacteria. The effect of addition of eggshell (BC/Eg) and eggshell-derived HAp (BC/HAp-Eg) on the bacterial cellulose yield, biodegradation and biocompatibility was studied. For comparison, HAp derived from chemical precursors was synthesized (BC/HAp-ch). The resultant composites were characterized by XRD, FTIR, and SEM/EDX. Furthermore, the biodegradation and bioactivity were assessed in SBF, and the cell viability was studied against oral normal cells. The results showed that the productivity of BC applied HAp-derived eggshell (1.83 g/L) was higher than that of using (1.37 g/L). Interestingly, the eggshell was converted to Ca3(PO4)2 during incubation in the bacterial culture medium, while Ca3(PO4)2 was formed as a secondary phase when using either eggshell-derived HAp or chemically-derived. The in vitro bioactivity test in SBF showed that all composites were induced the formation of a bone-like apatite layer on their surface with Ca/P ratio, 1.49, 1.35, and 1.41 for BC/Eg, BC/HAp-ch, and BC/HAp-Eg, respectively, near to the ratio in the natural HAp. Finally, the in vitro cell viability test was confirmed good biocompatibility against the composites. However, at high sample concentration (250 µg/mL), BC/HA-Eg showed the higher cell viability (95.2%) than that of BC/Eg (80.5%) and BC/HA-ch (86.2%). In conclusion, eggshell waste could be used directly with bacterial cellulose to produce bioactive composites without the need to convert it to HAp which reduced the cost of production and thus has a higher economic return. Obiviously, eggshell waste can act as calcium, organic matter source, pH preservation, nuterilizing agent along with potential instead of costly buffering agent in the BC culture medium and further for increased the BC production.

Rapid Flow Synthesis of a Biomimetic Carbonate Apatite as an Effective Drug Carrier

A facile synthesis of apatite nanocrystals analogous to bioapatites with increased biocompatibility and biodegradability can remedy the shortcomings of the widely applied synthetic hydroxyapatite (HAp) for bone defect treatment. Here, we propose an expeditious synthesis method to develop a biomimetic B-type carbonate apatite (CAp) with a simple capillary microfluidic device at room temperature. The process not only eliminates fluctuations with the addition of carbonate but also produces safe CAp drug carriers through simultaneous alendronate incorporation to the CAp structure. CAp displayed superior mineralization on osteoblast-like MG-63 cells when compared with HAp and HAp drug carriers that were produced using identical methods. Furthermore, alendronate-incorporated CAp drug carriers potentially displayed higher cancer cell suppression when applied to breast cancer cells attached to the bone tissue model, which signifies enhanced cancer metastasis to bone suppression due to the likelihood of increased alendronate release of CAp owing to its faster dissolution. Overall, our results may provide promising opportunities for enhanced clinical CAp application for bone defect treatment, particularly for bone loss and cancer to bone metastasis.

Influence of Terbium Ions and Their Concentration on the Photoluminescence Properties of Hydroxyapatite for Biomedical Applications

A new generation of biomaterials with terbium-doped hydroxyapatite was obtained using a coprecipitation method. The synthesis of new materials with luminescent properties represents a challenging but important contribution due to their potential applications in biomedical science. The main objective of this study was to revel the influence of terbium ions on the design and structure of hydroxyapatite. Different concentrations of terbium, described by the chemical formula Ca_10−xTb_x(PO₄)₆(OH)₂, where x is in the range of 0 to 1, were considered. The consequence of ion concentration on hydroxyapatite morphology was also investigated. The morphology and structure, as well as the optical properties, of the obtained nanomaterials were characterized using X-ray powder diffraction analysis (XRD), Fourier Transform Infrared spectrometry (FTIR), SEM and TEM microscopy, UV-Vis and photoluminescence spectroscopies. The measurements revealed that terbium ions were integrated into the structure of hydroxyapatite within certain compositional limits. The biocompatibility and cytotoxicity of the obtained powders evaluated using MTT assay, oxidative stress assessment and fluorescent microscopy revealed the ability of the synthesized nanomaterials to be used for biological system imaging.

Synthesis and Characterization of Photoluminescent Ce(III) and Ce(IV) Substituted Hydroxyapatite Nanomaterials by Co-Precipitation Method: Cytotoxicity and Biocompatibility Evaluation

Improved compounds of Ce(III) and Ce(IV)-doped hydroxyapatite (Ca_10-xCe_x(PO₄)₆(OH)₂) with different concentrations such as x = 0.5, 1, 2.5, 5, and 10%, obtained by the simple co-precipitation method were synthesized. The cerium (3⁺) and cerium (4⁺)-doped hydroxyapatite were evaluated for biocompatibility and fluorescence properties. It was found that the cerium-HAp powders were non-toxic, even at higher level of concentration. The synthesized powders were further characterized by FTIR spectrometry, UV-Vis spectroscopy, XRD diffraction, SEM and TEM analysis. Therefore, the present study proves that the developed cerium (3⁺) and cerium (4⁺)-doped hydroxyapatite, respectively can be widely used as luminescent labeling materials, with improved biological properties.

Mesoporous Mn-doped hydroxyapatite nanorods obtained via pyridinium chloride enabled microwave-assisted synthesis by utilizing Donax variabilis seashells for implant applications

Manganese-doped mesoporous hydroxyapatite (MnHAp) nanorods, a bio-apatite were synthesized via pyridinium chloride mediated microwave approach using bio-waste Donax variabilis seashells to treat orthopedic infections. This is the first report on using pyridinium chloride mediated mesoporous MnHAp nanorods synthesis. Pure and Mn doped HAp samples were examined using Raman spectroscopy, X-ray powder diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) studies to confirm the prepared HAp nanorods. Furthermore, the fabrication of manganese-doped HAp was successful with the formation of a hexagonal crystal lattice without disturbing the HAp phase. It is because, at the time of synthesis, PO₄^3- ions form an electrostatic interaction with the Mn ions. Furthermore, Mn-doped HAp samples showed a reduction in their sizes of 15, 10-15, 5-10 nm width, and 80-100, 10-15, 20-30 nm length with varied pore diameters and surface area. The pure HAp, MnHAp-1, MnHAp-2, and MnHAp-3 nanorods disclose the surface area of 39.4, 18.0, 49.2, and 80.4 m² g^-1, with a pore volume of 0.0102, 0.0047, 0.0143, and 0.0447 cm³ g^-1, the corresponding pore diameter was estimated to be 6, 7, 6, and 4 nm, respectively. Moreover, antibacterial activity reveals effective bactericidal action against infections causing pathogens whereas cytotoxicity examination (MTT assay), and zebrafish results reveal their non-toxic behavior. Therefore, it is evident from the study, that rapid fabrication of mesoporous and diverse structured MnHAp nanorods could be convenient with pyridinium chloride enabled microwave-assisted method as a bactericidal biomaterial for implant applications.

Hydrothermal synthesis of perfectly shaped micro- and nanosized carbonated apatite

Herein we present a Ca[EDTA]-based synthesis and comparative study of perfectly shaped plate-like, rod–like, and prism-like carbonated apatites.

Synthesis of Silicon- and Carbonate-doped Biomimetic Hydroxyapatite in the Presence of Citrate Ions and its Physicochemical, Bioactivity Properties

The present study investigated the phase composition, the structural, morphological, and bioactivity properties of silicon- and carbonate-doped biomimetic hydroxyapatite synthesized by precipitation from aqueous solutions in the presence of different amounts of citrate ions. The X-ray diffraction and Fourier transform infrared spectroscopy analyses confirmed that all the samples exhibited single-phase. Base on the results of the morphological study, all the obtained samples consisted of porous agglomerated particles made up of tiny crystallites in the nanometer range. The change in structural order, as well as the decrease in particle size and degree of crystallinity result from the presence of citrate ions were revealed by X-ray diffraction, dynamic light scattering, and scanning electron microscopy analyses. Bioactivity properties of samples were studied by analyzing their bioresorbability in physiological saline (ω (NaCl) = 0.9%) and evaluating their solubility in SBF solution after a certain period of soaking time. The amount of the released Ca2+ ions was found to increase with the increasing concentration of citrate ions introduced in the synthesis process. The better solubility of material with the presence of citrate ions was beneficial in the growth of apatite on its surface that made produced material more biocompatible.

Ultra-high molecular weight polyethylene bioactive composites with carbonated hydroxyapatite

To develop an orthopedic material for bone substitution, the substitute material must mimic living tissue from an anatomical and physiological point of view. The high wear and impact resistance besides the low friction coefficient, make ultra-high molecular weight polyethylene (UHMWPE) a suitable material to be used in orthopedic applications. However, UHMWPE is a bioinert material, not providing a proper interaction with the bone tissue surrounding to the implant. One way to mitigate this issue is improving UHMWPE bioactivity. This can be done by adding bioactive fillers in the polymeric matrix. In this work, UHMWPE composites were prepared by twin-screw extrusion. The fillers used were carbonated hydroxyapatite (CHA) and hybrids formed by precipitating CHA in collagens (hydrolyzed and type II). The results show that the fillers used caused a slight reduction in UHMWPE crystallinity degree, while both crystallization and melting temperatures remained almost unchanged. Dynamic-mechanical thermal analysis indicated a weak adhesion between filler and polymeric matrix, which is good from the biological point of view since the bioactive filler surface will be available to apatite deposition. The obtained materials exhibited good mechanical properties and in vitro bioactivity assay showed that all of the prepared materials are bioactive.

Enhanced Healing and Antimicrobial Efficacy of Chitosan-g-Polyacrylamide in a Rat Model of Gingival Ulcers

Patients in dental hospitals often experience oral ulcerative lesions, which lead to pain and affect the patient's quality of life. At present, the goal of treating oral ulcerative lesions with drugs is to reduce inflammation and promote ulcer healing. However, very few antibacterial and hemostatic drugs are designed to be suitable for the microenvironment of gingival ulcers. Based on this, we have designed a natural therapeutic agent for oral ulcerative lesions that meets the various requirements of oral ulcerative lesion medication. The chitosan-g-polyacrylamide (CP) copolymer is composed of chitosan as the main chain and polyacrylamide polymers as the side chains. Antibacterial experiments show that this polymer can effectively inhibit the proliferation of Gram-negative (Escherichia coli) and Gram-positive bacteria (Staphylococcus aureus). In vitro cell experiments also show that the CP copolymer is non-toxic, which is conducive to ulcer wound healing. Coagulation experiments prove that the CP copolymer can accelerate blood coagulation to stop bleeding. In experiments using a Wistar rat gingival ulcer model, the CP copolymer significantly promoted ulcer healing and shortened the healing time. These results indicate that the CP copolymer may serve as a potential therapeutic agent for oral ulcerative lesions.

Controllable Synthesis of Biomimetic Hydroxyapatite Nanorods with High Osteogenic Bioactivity

The development of biodegradable materials with high osteogenic bioactivity is important for achieving rapid bone regeneration. Although hydroxyapatite (HAp) has been applied as a biomaterial for bone engineering due to its good osteoconductivity, conventional synthetic HAp nanomaterials still lack sufficient osteogenesis, likely due to their high crystallinity and uncontrollable architecture. A design of HAp nanoparticles mimicking bone features may create good microenvironments that promote osteogenesis for rapid bone regeneration. In this study, HAp nanoparticles with a comparatively less crystalline structure and nanorod shapes mimicking biological HAp nanocrystals of natural bone were fabricated using a simple chemical precipitation approach with mild temperature control in the absence of any organic solvents. Transmission electron microscopy (TEM) indicated that HAp nanorods with aspect ratios from 2.0 to 4.4 were synthesized by adjusting the reaction time as well as the reaction temperature. Fourier transform infrared spectroscopy and X-ray diffraction experiments displayed that HAp nanorods prepared at 30 °C (HAp-30 with an aspect ratio of 2.9) had a low crystalline structure and B-type CO₃^2- substitution similar to those of natural HAp originating from bone tissue. The energy-dispersive spectroscopy (EDS) results showed that the Ca/P ratio of HAp-30 was 1.66 ± 0.13. An in vitro biological evaluation against rat bone marrow-derived mesenchymal stem cells indicated that the resulting HAp nanorods had excellent biocompatibility (with an ∼80-fold increase in IC50 compared to that of conventional HAp nanoparticles). Interestingly, the alkaline phosphatase (ALP), alizarin red S, and immunofluorescence staining results all showed that stem cells display an obvious osteogenesis dependence on the HAp nanostructure. Specifically, HAp nanorods with a moderate aspect ratio had the optimal osteogenic capacity (e.g., HAp-30 offered a 2.8-fold increase in ALP expression and a 4-fold increase in OCN expression relative to that provided by irregular HAp at day 14). It is expected that HAp nanorods with controllable architectures and size have potential as a kind of new bioactive bone filler for bone defect repair.

Impact of crystallinity and crystal size of nanostructured carbonated hydroxyapatite on pre-osteoblast in vitro biocompatibility

Nanostructured carbonated hydroxyapatite (nCHA) is a promising biomaterial for bone tissue engineering due to its chemical properties, similar to those of the bone mineral phase and its enhanced in vivo bioresorption. However, the biological effects of nCHA nanoparticles on cells and tissues are not sufficiently known. This study assessed the impact of exposing pre-osteoblasts to suspensions with high doses of nCHA nanoparticles with high or low crystallinity. MC3T3-E1 pre-osteoblasts were cultured for 1 or 7 days in a culture medium previously exposed to CHA nanoparticles for 1 day. Control groups were produced by centrifugation for removal of bigger nCHA aggregates before exposure. Interaction of nanoparticles with the culture medium drastically changed medium composition, promoting Ca, P, and protein adsorption. Transmission Electron microscopy revealed that exposed cells were able to internalize both materials, which seemed concentrated inside endosomes. No cytotoxicity was observed for both materials, regardless of centrifugation, and the exposure did not induce alterations in the release of pro-and anti-inflammatory cytokines. Morphological analysis revealed strong interactions of nCHA aggregates with cell surfaces, however without marked alterations in morphological features and cytoskeleton ultrastructure. The overall in vitro biocompatibility of nCHA materials, regardless of physicochemical characteristics such as crystallinity, encourages further studies on their clinical applications.

Superior removal of Co2+, Cu2+ and Zn2+ contaminants from water utilizing spongy Ni/Fe carbonate-fluorapatite; preparation, application and mechanism

Spongy Ni/Fe carbonate - fluorapatite was synthesized from natural phosphorite enriched with iron impurities. The morphological, chemical and structural features of the product were estimated using several techniques as XRD, SEM, EDX, and FT-IR. It exhibits spongy structure of nano and micro-pores. The average crystallite size is about 8.27 nm. The suitability of the product for considerable decontamination of Zn²⁺, Co²⁺, and Cu²⁺, ions from water was studied based on several reacting parameters. The equilibrium was attained after 240 min for Zn²⁺ and Co²⁺ ions while the adsorption equilibrium of Cu²⁺ reached after 120 min. The adsorption data for the selected metals was represented well by a pseudo-second-order model which revealed chemisorption uptake. The equilibrium studies were appraised based on traditional models and two advanced models were designed according to the statistical physical theories. The adsorption results highly fitted with Langmuir model followed rather than the other models. This indicated a monolayer adsorption for the metal ions by spongy Ni/Fe carbonate - fluorapatite. The estimated q_max values are 149.25 mg/g, 106.4 mg/g and 147.5 mg/g for the uptake of Zn²⁺, Co²⁺, and Cu²⁺, respectively. Based on monolayer models of one energy and two energies, the number of receptor adsorption sites, number of adsorbed metal ions per active site, the average number of sites which occupied by ions, mono layer adsorption quantity and the adsorption quantity after total saturation were calculated for the first time for such materials.

In vitro response of mesenchymal stem cells to biomimetic hydroxyapatite substrates: A new strategy to assess the effect of ion exchange

Biomaterials can interact with cells directly, that is, by direct contact of the cells with the material surface, or indirectly, through soluble species that can be released to or uptaken from the surrounding fluids. However, it is difficult to characterise the relevance of this fluid-mediated interaction separately from the topography and composition of the substrate, because they are coupled variables. These fluid-mediated interactions are amplified in the case of highly reactive calcium phosphates (CaPs) such as biomimetic calcium deficient hydroxyapatite (CDHA), particularly in static in vitro cultures. The present work proposes a strategy to decouple the effect of ion exchange from topographical features by adjusting the volume ratio between the cell culture medium and biomaterial (V_CM/V_B). Increasing this ratio allowed mitigating the drastic ionic exchanges associated to the compositional changes experienced by the material exposed to the cell culture medium. This strategy was validated using rat mesenchymal stem cells (rMSCs) cultured on CDHA and beta-tricalcium phosphate (β-TCP) discs using different V_CM/V_B ratios. Whereas in the case of β-TCP the cell response was not affected by this ratio, a significant effect on cell adhesion and proliferation was found for the more reactive CDHA. The ionic exchange, produced by CDHA at low V_CM/V_B, altered cell adhesion due to the reduced number of focal adhesions, caused cell shrinkage and further rMCSs apoptosis. This was mitigated when using a high V_CM/V_B, which attenuated the changes of calcium and phosphate concentrations in the cell culture medium, resulting in rMSCs spreading and a viability over time. Moreover, rMSCs showed an earlier expression of osteogenic genes on CDHA compared to sintered β-TCP when extracellular calcium fluctuations were reduced.

STATEMENT OF SIGNIFICANCE

Fluid mediated interactions play a significant role in the bioactivity of calcium phosphates. Ionic exchange is amplified in the case of biomimetic hydroxyapatite, which makes the in vitro characterisation of cell-material interactions especially challenging. The present work proposes a novel and simple strategy to explore the mechanisms of interaction of biomimetic and sintered calcium phosphates with mesenchymal stem cells. The effects of topography and ion exchange are analysed separately by modifying the volume ratio between cell culture medium and biomaterial. High ionic fluctuations interfered in the maturation of focal adhesions, hampering cell adhesion and leading to increased apoptosis and reduced proliferation rate.

Microwave-induced production of boron-doped HAp (B-HAp) and B-HAp coated composite scaffolds

The aim of the present study is to produce boron (B) doped hydroxyapatite (B-HAp), which has an osteoinductive property, and investigate in-vitro osteogenesis potential of B-HAp coated chitosan (B-HAp/Ch) scaffolds. At first, B-HAp was produced by the interaction of ions within the concentrated synthetic body fluid containing boron (B-SBF) with microwave energy. Boron incorporation into HAp structure was performed by the substitution of borate ions with phosphate and hydroxyl ions. Experiments were carried out with different microwave powers and exposure times, and optimum conditions for the production of B-HAp were determined. B-HAp precipitated from B-SBF by 600W microwave power has 1.15±0.11% (w/w) B, 1.40 (w/w) Ca/P ratio, 4.30±0.07% (w/w) carbonate content, 30±4nm rod-like morphology and bone-like amorphous structure. Then, chitosan scaffolds that were prepared by freeze-drying were coated with B-HAp by performing microwave-assisted precipitation in the presence of scaffolds to improve their bioactivities and mechanical properties. The formation of apatite layer and the penetration of apatites into the pores were observed by scanning electron microscopy (SEM). Fourier Transform Infrared spectroscopy (ATR-FTIR) and X-ray diffraction (XRD) analysis also confirmed the presence of B-HAp layer. As control, hydroxyapatite coated chitosan scaffolds (HAp/Ch) produced at the same conditions were used. The results of cell culture studies indicated that B releasing from scaffolds enhances proliferation and osteoblastic differentiation of MC3T3-E1 cells. This work emphasized the importance of the use of B within the scaffolds for enhancing in-vitro bone tissue engineering applications.

Preparation and Characterization of Lanthanum-Incorporated Hydroxyapatite Coatings on Titanium Substrates

Titanium (Ti) has been widely used in clinical applications for its excellent biocompatibility and mechanical properties. However, the bioinertness of the surface of Ti has motivated researchers to improve the physicochemical and biological properties of the implants through various surface modifications, such as coatings. For this purpose, we prepared a novel bioactive material, a lanthanum-incorporated hydroxyapatite (La-HA) coating, using a dip-coating technique with a La-HA sol along with post-heat treatment. The XRD, FTIR and EDX results presented in this paper confirmed that lanthanum was successfully incorporated into the structure of HA. The La-HA coating was composed of rod-like particles which densely compacted together without microcracks. The results of the interfacial shear strength test indicated that the incorporation of lanthanum increased the bonding strength of the HA coating. The mass loss ratios under acidic conditions (pH=5.5) suggested that the La-HA coatings have better acid resistance. The cytocompatibility of the La-HA coating was also revealed by the relative activity of alkaline phosphatase, cellular morphology and cell proliferation assay in vitro. The present study suggested that La-HA coated on Ti has promising potential for applications in the development of a new type of bioactive coating for metal implants.

Bone-like hydroxyapatite precipitated from 10×SBF-like solution by microwave irradiation

Microwave-assisted methods have been frequently used in many processes owing to their numerous advantages such as performing fast, efficient and homogenous processes and reducing side reactions. In view of these benefits, in this study it was purposed to produce bone-like hydroxyapatite (HA) by inducing biomimetic process with microwave-irradiation. This is why, concentrated body fluid (SBF) i.e. 10×SBF-like solution was used and it was precipitated in different microwave powers i.e. 90W, 360W, 600W, and 1200W and in different exposure times. For comparison, precipitation process was also carried out at room temperature for 6h and at 80°C for 1h. The obtained HA structures were characterized by appropriate instrumental techniques. As a result, microwave-induced precipitation at 600W for 9 times 30s was determined as the optimum condition for the production of HA which has similar properties to the cortical bone. At this condition, B-type HA with 9.22% (wt.) carbonate content, 1.61 Ca/P molar ratio and amorphous structure was obtained easily, rapidly and efficiently. So, this is the first time microwave technology has been used to precipitate HA from SBF solution.

Utilization of snail shells to synthesise hydroxyapatite nanorods for orthopedic applications

Snail shells have been successfully utilized to synthesize HA nanorods via facile microwave irradiation method in rapid manner using EDTA as a chelating agent.

Nanocomposite bone scaffolds based on biodegradable polymers and hydroxyapatite

In tissue engineering, development of an osteoconductive construct that integrates with host tissue remains a challenge. In this work, the effect of bone-like minerals on maturation of pre-osteoblast cells was investigated using polymer-mineral scaffolds composed of poly(propylene fumarate)-co-poly(caprolactone) (PPF-co-PCL) and nano-sized hydroxyapatite (HA). The HA of varying concentrations was added to an injectable formulation of PPF-co-PCL and the change in thermal and mechanical properties of the scaffolds was evaluated. No change in onset of degradation temperature was observed due to the addition of HA, however compressive and tensile moduli of copolymer changed significantly when HA amounts were increased in composite formulation. The change in mechanical properties of copolymer was found to correlate well to HA concentration in the constructs. Electron microscopy revealed mineral nucleation and a change in surface morphology and the presence of calcium and phosphate on surfaces was confirmed using energy dispersive X-ray analysis. To characterize the effect of mineral on attachment and maturation of pre-osteoblasts, W20-17 cells were seeded on HA/copolymer composites. We demonstrated that cells attached more to the surface of HA containing copolymers and their proliferation rate was significantly increased. Thus, these findings suggest that HA/PPF-co-PCL composite scaffolds are capable of inducing maturation of pre-osteoblasts and have the potential for use as scaffold in bone tissue engineering.

Synthesis and characterization of xanthan-hydroxyapatite nanocomposites for cellular uptake

In this work xanthan-nanohydroxyapatite (XnHAp) and its equivalent strontium substituted (XnHApSr) were synthesized by the precipitation of nanohydroxyapatite in xanthan aqueous solution, characterized and compared to conventional hydroxyapatite particles (HAp). XnHAp and XnHApSr were less crystalline than HAp, as revealed by X-ray diffraction. Xanthan chains enriched the surface of XnHAp and XnHApSr particles, increasing the zeta potential values from -(7±1)mV, determined for HAp, to -(17±3)mV and -(25±3)mV, respectively. This effect led to high colloidal stability of XnHAp and XnHApSr dispersions and acicular particles (140±10)nm long and (8±2)nm wide, as determined by scanning electron microscopy and atomic force microscopy. XnHAp and XnHApSr particles were added to xanthan hydrogels to produce compatible nanocomposites (XCA/XnHAp and XCA/XnHApSr). Dried nanocomposites presented surface energy, Young's modulus and stress at break values comparable to those determined for bare xanthan matrix. Moreover, adding XnHAp or XnHApSr nanoparticles to xanthan hydrogel did not influence its porous morphology, gel content and swelling ratio. XCA/XnHAp and XCA/XnHApSr composites proved to be suitable for osteoblast growth and particularly XCA/XnHapSr composites induced higher alkaline phosphatase activity.

An efficient biomimetic coating methodology for a prosthetic alloy

The combination of the load-bearing metallic implants with the bioactive materials in the design of synthetic implants is an important aspect in the biomaterials research. Biomimetic coating of bioinert alloys with calcium phosphate phases provides a good alternative to the prerequisite for the continual replacement of implants because of the failure of bone-implant integration. We attempted to accelerate the biomimetic coating process of stainless steel alloy (316L) with biomimetic apatite. In addition, we investigated the incorporation of functioning minerals such as strontianite and smithsonite into the deposited layer. In order to develop a highly mature apatite coating, our method requires soaking of the pre-treated alloy in highly concentrated synthetic body fluid for only few hours. Surface characterizations were performed by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). Also, the deposited apatitic layers were analysed by powder diffraction X-ray analysis (XRD). 316L surface showed the growth of highly crystalline, low carbonated hydroxyapatite, after only 6h of the whole soaking process.

Substituted hydroxyapatites for bone repair

Calcium phosphates such as hydroxyapatite have a wide range of applications both in bone grafts and for the coating of metallic implants, largely as a result of their chemical similarity to the mineral component of bone. However, to more accurately mirror the chemistry, various substitutions, both cationic (substituting for the calcium) and anionic (substituting for the phosphate or hydroxyl groups) have been produced. Significant research has been carried out in the field of substituted apatites and this paper aims to summarise some of the key effect of substitutions including magnesium, zinc, strontium, silicon and carbonate on physical and biological characteristics. Even small substitutions have been shown to have very significant effects on thermal stability, solubility, osteoclastic and osteoblastic response in vitro and degradation and bone regeneration in vivo.

Rapid hydrothermal flow synthesis and characterisation of carbonate- and silicate-substituted calcium phosphates

A range of crystalline and nano-sized carbonate- and silicate-substituted hydroxyapatite has been successfully produced by using continuous hydrothermal flow synthesis technology. Ion-substituted calcium phosphates are better candidates for bone replacement applications (due to improved bioactivity) as compared to phase-pure hydroxyapatite. Urea was used as a carbonate source for synthesising phase pure carbonated hydroxyapatite (CO₃-HA) with ≈5 wt% substituted carbonate content (sample 7.5CO₃-HA) and it was found that a further increase in urea concentration in solution resulted in biphasic mixtures of carbonate-substituted hydroxyapatite and calcium carbonate. Transmission electron microscopy images revealed that the particle size of hydroxyapatite decreased with increasing urea concentration. Energy-dispersive X-ray spectroscopy result revealed a calcium deficient apatite with Ca:P molar ratio of 1.45 (±0.04) in sample 7.5CO₃-HA. For silicate-substituted hydroxyapatite (SiO₄-HA) silicon acetate was used as a silicate ion source. It was observed that a substitution threshold of ∼1.1 wt% exists for synthesis of SiO₄-HA in the continuous hydrothermal flow synthesis system, which could be due to the decreasing yields with progressive increase in silicon acetate concentration. All the as-precipitated powders (without any additional heat treatments) were analysed using techniques including Transmission electron microscopy, X-ray powder diffraction, Differential scanning calorimetry, Thermogravimetric analysis, Raman spectroscopy and Fourier transform infrared spectroscopy.

Innovative magnetic scaffolds for orthopedic tissue engineering

The use of magnetism in tissue engineering is a very promising approach, in fact magnetic scaffolds are able not only to support tissue regeneration, but they can be activated and work like a magnet attracting functionalized magnetic nanoparticles (MNPs) injected close to the scaffold enhancing tissue regeneration. This study aimed to assess the in vivo biocompatibility and osteointegrative properties of novel magnetic scaffolds. Two hydroxyapatite/collagen (70/30 wt %) magnetic scaffolds were magnetized with two different techniques: direct nucleation of biomimetic phase and superparamagnetic nanoparticles (MNPs) on self-assembling collagen fibers (MAG-A) and scaffold impregnation in ferro-fluid solution (MAG-B). Magnetic scaffolds were implanted in rabbit distal femoral epiphysis and tibial mid-diaphysis. Histopathological screening showed no inflammatory reaction due to MNPs. Significantly higher bone healing rate (ΔBHR) results were observed in MAG-A in comparison to MAG-B. Significant differences were also found between experimental times with an increase in ΔBHR from 2 to 4 weeks for both scaffolds in trabecular bone, while only for MAG-B (23%, p < 0.05) in cortical bone. The proposed magnetic scaffolds seem to be promising for magnetic guiding in orthopedic tissue engineering applications and they will be suitable to treat also several pathologies in regenerative medicine area.

Hydroxyapatite formation from cuttlefish bones: kinetics

Highly porous hydroxyapatite (Ca(10)(PO(4))(6)·(OH)(2), HA) was prepared through hydrothermal transformation of aragonitic cuttlefish bones (Sepia officinalis L. Adriatic Sea) in the temperature range from 140 to 220°C for 20 min to 48 h. The phase composition of converted hydroxyapatite was examined by quantitative X-ray diffraction (XRD) using Rietveld structure refinement and Fourier transform infrared spectroscopy (FTIR). Johnson-Mehl-Avrami (JMA) approach was used to follow the kinetics and mechanism of transformation. Diffusion controlled one dimensional growth of HA, predominantly along the a-axis, could be defined. FTIR spectroscopy determined B-type substitutions of CO(3) (2-) groups. The morphology and microstructure of converted HA was examined by scanning electron microscopy. The general architecture of cuttlefish bones was preserved after hydrothermal treatment and the cuttlefish bones retained its form with the same channel size (~80 × 300 μm). The formation of dandelion-like HA spheres with diameter from 3 to 8 μm were observed on the surface of lamellae, which further transformed into various radially oriented nanoplates and nanorods with an average diameter of about 200-300 nm and an average length of about 8-10 μm.

Preparation and characterization of hydroxyapatite-coated iron oxide particles by spray-drying technique

Magnetic particles of iron oxide have been increasingly used in medical diagnosis by magnetic resonance imaging and in cancer therapies involving targeted drug delivery and magnetic hyperthermia. In this study we report the preparation and characterization of iron oxide particles coated with bioceramic hydroxyapatite by spray-drying. The iron oxide magnetic particles (IOMP) were coated with hydroxyapatite (HAp) by spray-drying using two IOMP/HAp ratios (0.7 and 3.2). The magnetic particles were characterized by way of scanning electronic microscopy, energy dispersive X-ray, X-ray diffraction, Fourier transformed infrared spectroscopy, flame atomic absorption spectrometry,vibrating sample magnetometry and particle size distribution (laser diffraction). The surface morphology of the coated samples is different from that of the iron oxide due to formation of hydroxyapatite coating. From an EDX analysis, it was verified that the surface of the coated magnetic particles is composed only of HAp, while the interior containsiron oxide and a few layers of HAp as expected. The results showed that spray-drying technique is an efficient and relatively inexpensive method for forming spherical particles with a core/shell structure.