Removal of pentachlorophenol pesticide from aqueous solutions using modified chitosan

Low-cost materials as vehicles for pesticides in aquatic media: a review of the current status of different biosorbents employed, optimization by RSM approach

Water contamination by pesticides is increasing dramatically due to population growth and the extensive use of pesticides in agriculture, leading to grave environmental and health concerns. Thus, efficient processes and the design and development of effective treatment technologies are required due to the enormous demand for fresh water. The adsorption approach has been widely used to remove organic contaminants such as pesticides because of its performance, less expense, high selectivity, and simplicity of operation compared to other treatment technologies. Among alternative adsorbents, biomaterials abundantly available for pesticide sorption from water resources have attracted the attention of researchers worldwide. The main objective of this review article is to (i) present studies on a wide range of raw or chemically modified biomaterials potentially effective in removing pesticides from aqueous media; (ii) indicating the effectiveness of biosorbents as green and low-cost materials for removing pesticides from wastewater; and (iii) furthermore, report the application of response surface methodology (RSM) for modeling and optimizing adsorption.

Occurrence, fate, and potential impacts of wood preservatives in the environment: Challenges and environmentally friendly solutions

Wood preservation has gained global prevalence in recent years, primarily owing to the renewable nature of wood and its capacity to act as a carbon sink. Wood, in its natural form, lacks intrinsic resilience and is prone to decay if left untreated; hence, wood preservatives (WPs) are used to improve wood's longevity. The fate and potential hazards of wood preservatives to human health, ecosystems, and the environment are complex and depend on various aspects, including the type of the preservative compounds, their physicochemical properties, application methods, exposure pathways, environmental conditions, and safety measures and guidelines. The occurrence and distribution of WPs in environmental matrices such as soil and water can result in hazardous pollutants seeping into surface water, groundwater, and soil, posing health hazards, and polluting the environment. Bioremediation is crucial to safeguarding the environment and effectively removing contaminants through hydrolytic and/or photochemical reactions. Phytoremediation, vermicomposting, and sustainable adsorption have demonstrated significant efficacy in the remediation of WPs in the natural environment. Adsorbents derived from biomass waste have been acknowledged for their ability to effectively remove WPs, while also offering cost-efficiency and environmental sustainability. This paper aims to identify wood preservatives' sources and fate in the environment and present a comprehensive overview of the latest advancements in environmentally friendly methods relevant to the removal of the commonly observed contaminants associated with WPs in environmental matrices.

Exposure assessment of nitrate and phenol derivatives in Tehran's water distribution system

The presence of organic and inorganic contaminants in drinking water is a global concern. Nitrate and phenol derivatives are examples of pollutants that could be of anthropogenic origin. They are associated with numerous health risks, underscoring the importance of monitoring their presence in drinking water. This study aimed to measure nitrate and phenol derivatives, including 2,4-Dichlorophenol (2,4-DCP), Pentachlorophenol (PCP), 2,4,5-Trichlorophenol (2,4,5-TCP), 2-Chlorophenol (2-CP), 4-Chlorophenol (4-CP), and phenol, in Tehran's water distribution system (WDS). The pollutants in Tehran's WDS were significantly and positively correlated with precipitation. The Hazard Quotient (HQ) and the Excess Lifetime Cancer Risk (ELCR) of the detected pollutants were estimated. The results showed that the regional mean of nitrate and PCP in Tehran's WDS were 35.58±8.71mg L-1 and 76.14±16.93 ng L-1 lower than the guideline values of 50 mg L-1 and 1000 ng L-1, respectively. Some districts exhibited nitrate concentration exceeding the allowable limit by a factor of 1.2 to 2.3. Consequently, the nitrate intake in some districts constituted approximately 50% of the reference dose. While PCP as a phenol derivative with more health concerns was identified in Tehran's WDS, the likelihood of its health effects was determined to be negligible.

Designing a novel poly (methyl vinyl ether maleic anhydride) based polymeric membrane with enhanced antifouling performance for removal of pentachlorophenol from aqueous solution

In this current study, poly (methyl vinyl ether maleic anhydride) (PMVEAMA), a sustainable additive, was incorporated into poly (ether-ether sulfone) (PEES) polymer to design a novel polymeric hybrid membrane for the efficient filtration of toxic pentachlorophenol (PCP) from an aqueous medium. Hydrophilic additives significantly altered the membrane's morphology, structure, porosity, water content, and flux performance compared to the bare PEES membrane. The influence of PMVEAMA on the structural modification of the synthesized polymer membrane was confirmed by SEM, ATR-FTIR, XRD, AFM, zeta potential and contact angle. Findings revealed that the addition of PMVEAMA to the PEES polymer enhances the porosity (17.7%-28.9%), water content (29.8%-39.8%), and pure water flux (186 Lm^-2h^-1 to 349 Lm^-2h^-1). The effect of PMVEAMA concentration on the PEES membrane exhibited more finger like pores, better porosity and hydrophilicity, reduced surface roughness, fouling and increased permeability. The fouling studies exhibit an improved 57% PCP rejection and permeation flux of 22.3 Lm^-2h^-1 due to the addition of the hydrophilic additive. Surprisingly, the incorporation of PMVEAMA into the bare PEES membrane resulted in a high flux recovery ratio of 73.7%. The antifouling properties and enhanced permeability of the PEES/PMVEAMA membrane indicates its potential application in water purification sectors for the efficient separation of contaminants.

Explanation of difenoconazole removal by chitosan with Langmuir adsorption isotherm and kinetic modeling

In this study, the adsorption of toxic difenoconazole pesticide was investigated by using chitosan. In the first phase of the study, chitosan was extracted from deep-water pink shrimp (Parapenaeus longirostris) shells, by deacetylation of the chitin, which is separated and disposed of after meat extraction in processing facilities in Turkey. The deacetylation degree, molecular weight, viscosity, moisture, and crude-ash values of the extracted chitosan were determined. Chitosan, having a high deacetylation degree (90.21%), was used as the adsorbent. In the second phase of the study, the effects of pH, temperature, and pesticide concentration on the adsorption were investigated. The optimum pH level for pesticide adsorption was determined as 5. It was observed that the adsorption increases as the temperature increases. A rapid increase was observed within the first 5 min of the 60-minute adsorption process in difenoconazole concentrations of 5, 15, and 25 µg/L, and after 10 min, the adsorption rate was stable. The Langmuir isotherm parameters regarding the adsorption were determined as aL = 0.635, kL = 15.10, and the Qmax value was calculated as 23.77 mg/g. In the evaluation of overall study results, it was determined that the chitosan biopolymer is a suitable adsorbent for difenoconazole pesticide adsorption.

Versatile mechanisms and enhanced strategies of pollutants removal mediated by Shewanella oneidensis: A review

The removal of environmental pollutants is important for a sustainable ecosystem and human health. Shewanella oneidensis (S. oneidensis) has diverse electron transfer pathways and can use a variety of contaminants as electron acceptors or electron donors. This paper reviews S. oneidensis's function in removing environmental pollutants, including heavy metals, inorganic non-metallic ions (INMIs), and toxic organic pollutants. S. oneidensis can mineralize o-xylene (OX), phenanthrene (PHE), and pyridine (Py) as electron donors, and also reduce azo dyes, nitro aromatic compounds (NACs), heavy metals, and iodate by extracellular electron transfer (EET). For azo dyes, NACs, Cr(VI), nitrite, nitrate, thiosulfate, and sulfite that can cross the membrane, S. oneidensis transfers electrons to intracellular reductases to catalyze their reduction. However, most organic pollutants cannot be directly degraded by S. oneidensis, but S. oneidensis can remove these pollutants by self-synthesizing catalysts or photocatalysts, constructing bio-photocatalytic systems, driving Fenton reactions, forming microbial consortia, and genetic engineering. However, the industrial-scale application of S. oneidensis is insufficient. Future research on the metabolism of S. oneidensis and interfacial reactions with other materials needs to be deepened, and large-scale reactors should be developed that can be used for practical engineering applications.

Optimization of the Pentachlorophenol Adsorption by Organo-Clays Based on Response Surface Methodology

The aim of this study is to optimize the adsorption of pentachlorophenol (PCP) using an organo-clay under the response surface methodology. The adsorbent was selected from a montmorillonite exchanged by various cations, such as Fe³⁺, Al³⁺, Zn²⁺, Mg²⁺, Na⁺, and modified by bromide cetyltrimethylammonium (CTAB) as surfactant. The obtained organo-montmorillonite was characterized using several techniques, such as Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and nitrogen adsorption, performed at -196 °C. The results showed an increase in basal space from 1.65 to 1.88 nm and a decrease in the specific surface and pore volume, with an increase in pore diameter, including the presence of characteristic bands of -CH₂- and -CH₃- groups at 2926 and 2854 cm^-1 in the FTIR spectrum after the modification. The optimization of PCP removal by clay adsorbents is achieved using the response surface methodology (RSM) with a four-factor central composite model, including pH of solution, mass of adsorbent, contact time, and initial concentration. The results proved the validity of the regression model, wherein the adsorption capacity reaches its maximum value of 38 mg/g at a lower adsorbent mass of 20 mg, pH of 6, contact time (t_c) of 5 h, and initial concentration of 8 mg/L.

Isolation and test of novel yeast strains with lignin usage capability and phenolic compound resistance

Five yeast fungi strains (i.e., two Cryptococcus albidus, one Candida guillermondii, and two Candida tropicalis) were isolated from sugarcane and tested for their use of lignin as sole carbon source and their potential to grow in the presence of phenol and phenol derivatives (i.e., pentachlorophenol and p-nitrophenol). The full set of isolated yeasts showed ligninolytic activity, achieving at least 36% lignin degradation after 25 days. The C. albidus JS-B1 strain had the highest ligninolytic activity, achieving 27% lignin degradation within 4 days. This increased activity was associated with the production of ligninolytic laccase enzymes. All the tested yeast fungi strains showed growth in the presence of high concentrations of phenolic compounds (i.e., 900 mg/L phenol, 200 mg/L p-nitrophenol, 50 mg/L pentachlorophenol) and showed significant potential for lignin and lignin by-product degradation. Each of these five strains has the potential to be used in biological treatment processes for contaminated effluents from paper pulping and bleaching or phenol and phenol-derivative biodegradation processes for other industrial wastewater effluents.

Mango Seed-Derived Hybrid Composites and Sodium Alginate Beads for the Efficient Uptake of 2,4,6-Trichlorophenol from Simulated Wastewater

In this study, mango seed shell (MS)-based hybrid composite and composite beads (FeCl3-NaBH4/MS and Na-Alginate/MS) were designed. Batch and column experimental analyses were performed for the uptake of 2,4,6-trichlorophenol (2,4,6-TCP) from wastewater. The physicochemical characteristics of both composites were also examined. From the batch adsorption experiments, the best adsorption capacities of 28.77 mg/g and 27.42 mg/g were observed in basic media (pH 9–10) at 308 K for FeCl3-NaBH4/MS and 333 K for Na-Alginate/MS with 25 mg/L of 2,4,6-TCP concentration for 120 min. The rate of reaction was satisfactorily followed by the pseudo-second-order kinetics. Equilibrium models revealed that the mechanism of reaction followed the Langmuir isotherm. The thermodynamic study also indicated that the nature of the reaction was exothermic and spontaneous with both adsorbents. Desorption experiments were also carried out to investigate the reliability and reusability of the composites. Furthermore, the efficiency of the adsorbents was checked in the presence of different electrolytes and heavy metals. From the batch experimental study, the FeCl3-NaBH4/MS composite proved to be the best adsorbent for the removal of the 2,4,6-TCP pollutant, hence it is further selected for fixed-bed column experimentation. The column study data were analyzed using the BDST and Thomas models and the as-selected FeCl3-NaBH4/MS hybrid composites showed satisfactory results for the fixed-bed adsorption of the 2,4,6-TPC contaminants.

Pb(II) adsorption mechanism and capability from aqueous solution using red mud modified by chitosan

Red mud modified by chitosan (RM/CS) was utilized as an adsorbent to effectively remove Pb(II) from aqueous solution. The surface area of RM/CS was found to significantly increase by more than 50% compared to that of original red mud. Different factors that affected the Pb(II) removal on this material, such as initial Pb(II) concentration, pH, and contact time, were investigated. The pseudo-first-order, pseudo-second-order, and intra-diffusion models were used to fit the experimental data to investigate the Pb(II)'s removal kinetics. The Pb(II) removal followed the intra-diffusion model. Additionally, the non-zero C value obtained from this model indicates that the removal was controlled by many different mechanisms. We also found that the interaction of Pb(II) and carbonate group on the material's surface played a primary role once the adsorption equilibrium was reached. Finally, the maximum adsorptive capacity was found to be about 209 mg/g. This obtained value is higher than those obtained for some other materials. Therefore, the present RM/CS should be a potential material for removing Pb(II) from aqueous solution.

Magnetic nanobiosorbent (MG-Chi/Fe3 O4 ) for dispersive solid-phase extraction of Cu(II), Pb(II), and Cd(II) followed by flame atomic absorption spectrometry determination

Trace amounts of Cu (II), Pb (II), and Cd (II) in a wastewater sample were preconcentrated with a novel cross‐linked magnetic chitosan modified with a new synthesised methionine‐glutaraldehyde Schiff's base (MG‐Chi/Fe₃O₄) as a dispersive solid‐phase extraction (DSPE) adsorbent. The adsorbed metal ions were then eluted with a specific volume of suitable solution and determined by flame atomic absorption spectrometry (FAAS). Various parameters affecting the extraction efficiency of the metal ions were investigated and optimised, including pH, amount of adsorbent, extraction time, type and volume rate of eluent, elution time, sample volume, and effect of interfering ions. The adsorption kinetics are more consistent with the pseudo‐second order model. The results were statistically interpreted and the analytical performance of the proposed method was found to have preconcentration factors of 55, 60, and 50 μg L⁻¹ for Cu(II), Pb(II), and Cd(II), respectively, limits of detection were 0.22, 0.24, and 0.10 μg L⁻¹ for Cu(II), Pb(II), and Cd(II), respectively, with a relative standard deviation (1.5%‐2.8 %), and the liner range was 5–1000 for Cu(II) and Pb(II) and 2.5–1000 for Cd(II). It was concluded that this method was suitable for successful simultaneous determination of Cu(II), Pb(II), and Cd(II) in industrial wastewater samples.

Risk assessment and the adsorptive removal of some pesticides from synthetic wastewater: a review

Background

The need for environmental protection and remediation processes has been an increasing global concern. Pesticides are used as biological agents, disinfectants, antimicrobials, and also in a mixture of some chemical substances. Their modes of application are through selective dispensing and attenuation processes which act upon any pest that compete with the production, processing, and storage of foods and also in agricultural commodes. The pests might comprise weeds, insects, birds, fish, and microbes.

Main body

Pesticides are commonly found in water surface, landfill leachate, ground water, and wastewater as pollutant. An overview of recently studied adsorption processes for the pesticide elimination from polluted water has been reported in this study utilizing activated carbon, clay materials, biomass materials, metal organic frame work, graphene, and carbon-based materials as well as agricultural wastes as adsorbents. The risk assessment and cost analysis of adsorbents were also provided.

Conclusion

Evidences from literature recommend modified adsorbent and composite materials to have a prospective use in pesticide removal from wastewater. The adsorption data obtained fitted into different isotherm and kinetic models and also the thermodynamic aspect have been discussed.

Graphical abstract

Electrocatalytic oxidation of PCP-Na by a novel nano-PbO2 anode: degradation mechanism and toxicity assessment

This study aims at investigating the electrocatalytic oxidation of sodium pentachlorophenate (PCP-Na) using a novel nano-PbO₂ powder anode. The nano-PbO₂ powder (marked as HL-PbO₂) was prepared by a simple hydrolysis process, and hydrothermal treatment was followed to improve the activity of HL-PbO₂. The HL-PbO₂ treated for 24 h by hydrothermal process (HL/HT-PbO₂-24) was confirmed to possess higher crystallinity, higher oxygen evolution potential, and more active sites, resulting in stronger OH radical generation capacity and higher electrochemical activity. Compared with conventional electrodeposited PbO₂ (ED-PbO₂) anode, the HL/HT-PbO₂-24 anode showed higher PCP-Na degradation rate. Under the same operating conditions, the mineralization current efficiency at HL/HT-PbO₂-24 was 2.7 times than that at ED-PbO₂. Five intermediates were detected in PCP-Na degradation solution and possible degradation mechanism of PCP-Na was discussed. In addition, the acute toxicity of PCP-Na degradation solution to zebrafish embryos and the oxidative stress induced in zebrafish embryos/larvae were studied to evaluate the ecological security of electrocatalytic oxidation of PCP-Na.

Synthesis and Insecticidal Activity Evaluation of Virtually Screened Phenylsulfonamides

The fastest and most effective way to control pests is to use pesticides. However, with the accumulation of pesticide resistance and the difficulties of rapidly producing new pesticides, it is of great significance to create new pesticides through new synthetic methods. In this study, we report a computer-aided drug design (CADD)-assisted method to obtain two lead sulfonamides by homology modeling and virtual screening. On this basis, the lead compounds were synthesized from p-chlorocresol by four steps of esterification, sulfonation, sulfonamidation, and amidation. Further, 71 derivatives were synthesized by optimizing the lead compounds, and their insecticidal activities against Mythimna separata were evaluated by the leaf-dipping method. Notably, seven sulfonamides (5a, 5g, 5h, 5m, 6b, 6g, and 6m) with excellent insecticidal activity were obtained, and the possible binding modes between receptors and active groups in sulfonamides were verified by structure-activity relationship and docking simulation, which provided theoretical support for the subsequent development of these novel candidate insecticides.

Pesticides in aquatic environments and their removal by adsorption methods

Although pesticides are widely used in agriculture, industry and households, they pose a risk to human health and ecosystems. Based on target organisms, the main types of pesticides are herbicides, insecticides and fungicides, of which herbicides accounted for 46% of the total pesticide usage worldwide. The movement of pesticides into water bodies occurs through run-off, spray drift, leaching, and sub-surface drainage, all of which have negative impacts on aquatic environments and humans. We sought to define the critical factors affecting the fluxes of contaminants into receiving waters. We also aimed to specify the feasibility of using sorbents to remove pesticides from waterways. In Karun River in Iran (1.21 × 10⁵ ng/L), pesticide concentrations are above regulatory limits. The concentration of pesticides in fish can reach 26.1 × 10³ μg/kg, specifically methoxychlor herbicide in Perca fluviatilis in Lithuania. During the last years, research has focused on elimination of organic pollutants, such as pesticides, from aqueous solution. Pesticide adsorption onto low-cost materials can effectively remediate contaminated waters. In particular, nanoparticle adsorbents and carbon-based adsorbents exhibit high performance (nearly 100%) in removing pesticides from water bodies.

Fate of environmental pollutants

This annual review covers the literature published in 2018 on topics related to the occurrence and fate of environmental pollutants in wastewater. Due to the vast amount of literature published on this topic, we have discussed only a portion of the quality research publications, due to the limitation of space. The abstract search was carried out using Web of Science, and the abstracts were selected based on their relevance. In a few cases, full-text articles were referred to understand new findings better. This review is divided into the following sections: antibiotic-resistant bacteria (ARBs) and antibiotic-resistant genes (ARGs), disinfection by-products (DBPs), drugs of abuse (DoAs), estrogens, heavy metals, microplastics, per- and polyfluoroalkyl compounds (PFAS), pesticides, and pharmaceuticals and personal care products (PPCPs), with the addition of two new classes of pollutants to previous years (DoAs and PFAS).

Removal of pirimicarb from agricultural waste water using cellulose acetate-modified ionic liquid membrane

Insecticide spray in fruit gardens is a very common practice in different districts of Pakistan. These toxic sprays not only deteriorate the taste of fruit but also due to wet deposition travel through soil, they reach groundwater via leaching process. In the present study, imidazolium-based ionic liquid ([C₂im][C₃H₆NH₂]Br^-) and its cellulose acetate-supported membrane ([CA-C₂im][C₃H₆NH₂]Br^-) was prepared and characterized using FTIR, XRD, and SEM. These materials are used as adsorbents for the removal of "Pirimicarb" (an insecticide from waste water). A closed batch at varying parameters, i.e., concentration and temperature as function of time, was conducted on UV-Vis spectrophotometer. Comparison of removal capacity exposed better (74%) adsorption trend by CA-IL membrane than ionic liquid (68%). Thermodynamic studies projected spontaneous process (-ΔG), favoring endothermic reaction (ΔH, ΔS). Kinetics supported pseudo-second order reaction while fitness of isothermic models (Langmuir, Freundlich, Temkin) proposed multistep intraparticle diffusion process.

Potent drug candidature of an ONS donor tethered copper (II) complex: Anticancer activity, cytotoxicity and spectroscopically approached BSA binding studies

In our continued efforts to develop metal based therapeutic agents, we have synthesized a novel copper(II) complex, [{Cu(hpdbal-sbdt)}₂] (2) tethered with a biocompatible ONS^2- donor backbone [H₂hpdbal-sbdt] (1) [H₂hpdbal-sbdt is a tridentate ligand derived from S-benzyldithiocarbazate (Hsbdt) and 2-hydroxy-5-(phenyldiazenyl)benzaldehyde (Hhpdbal)]. The metal complex (2) was characterized using attenuated total reflection-infrared (ATR-IR) spectroscopy, electron paramagnetic resonance (EPR) spectroscopy, thermogravimetry and differential scanning calorimetric (TG-DSC) analysis, field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS) and elemental (CHNS) analysis. The antineoplastic ability of copper complex was evaluated in vitro against human cervical cancer (HeLa) cells. MTT assay results showed that the copper complex exhibited significant growth inhibition of HeLa cells with an IC₅₀ value of 4.46 μM and this value was compared with reported standards. Cytotoxicity of the copper complex towards human embryonic kidney cells (HEK-293) was also evaluated. The potentially active copper complex was studied for its solution state stability at a pH range of 3-9. Following this, the interactive behaviour of the bioactive copper complex with a drug transporter protein (BSA) was deciphered through multi-spectrosopic investigations like steady-state fluorescence, three-dimensional fluorescence, deconvoluted-IR and UV-Visible techniques.

In vitro apoptosis-induction, antiproliferative and BSA binding studies of a oxidovanadium(V) complex

In our ongoing efforts to develop novel trace metal complexes with therapeutically interesting properties, a neutral mono nuclear oxidomethoxidovanadium(V) complex, [V^VO(OCH₃)(hpdbal-sbdt)] (1) and a μ-O bridged dinuclear oxidovanadium(V) complex, [{V^VO(hpdbal-sbdt)}₂μ-O] (2) [H₂hpdbal-sbdt (I) is a tridentate and dibasic ONS^2- donor ligand obtained through the Schiff base reaction of 2-hydroxy-5-(phenyldiazenyl)benzaldehyde (Hhpdbal) and S-benzyldithiocarbazate (Hsbdt)] have been synthesized and characterized by various analytical techniques such as TGA, EDS, ATR-IR, UV-Vis, CV, ¹H NMR, ¹³C NMR and ⁵¹V NMR. Single-crystal X-ray diffraction analysis of 1 confirms the coordination of phenolate oxygen, imine nitrogen and thioenolate sulfur of the ligand to the vanadium center with a distorted tetragonal-pyramidal geometry. The compound 2 triggered apoptotic and reproductive death of the cancer cells in vitro with 76% and 62% growth inhibition of human breast adenocarcinoma (MCF-7) and human lung carcinoma cells (A549) respectively. The compound 2 was found to be sufficiently stable over a wide window of physiological pH. The complex 2 was studied further for its interaction with a drug carrier protein BSA with the aid of spectroscopic techniques viz. fluorescence, temperature controlled UV-vis and deconvoluted IR techniques.

A novel biocompatible NiII tethered moiety as a glucose uptake agent and a hit against methicillin-resistant Staphylococcus aureus

In the efforts to develop a biocompatible transition metal complex as a drug alike for some of the prevailing non-communicable diseases (NCDs) and communicable diseases (CDs), a novel binuclear Ni^II compound [{Ni^II(hpdbal-sbdt)}₂] (2) has been synthesized by the reaction of Ni(OAc)₂.4H₂O and H₂hpdbal-sbdt (1) [1 is a dibasic tridentate ONS^2- donor Schiff base ligand obtained by the condensation of 2-hydroxy-5-(phenyldiazenyl)benzaldehyde (Hhpdbal) and S-benzyldithiocarbazate (Hsbdt)]. Both ligand 1 and compound 2 were structurally characterized in the solid and solution state using various spectroscopic techniques like ATIR, ¹H NMR, ¹³C NMR, TGA, FESEM, EDS and CHNS analysis. The antidiabetic activity of H₂hpdbal-sbdt (1) and [{Ni^II(hpdbal-sbdt)}₂] (2) were assessed using 2-NBDG uptake assay. The assay results showed 85% and 95% of fluorescent glucose uptake by insulin resistant HePG2 cells treated with compounds 1 and 2 respectively. The 2-NBDG uptake by the cells treated with the compound 2 was observed to be comparable to the standard antidiabetic drug metformin. Compounds 1 and 2 were also tested against five bacterial and two fungi strains in order to evaluate pathogen killing activity. Compound 2 showed significant inhibitory action towards the methicillin-resistant Staphylococcus aureus (MRSA) strain with an MIC value of 2 μg/mL whereas the ligand 1 was found to be inactive. Furthermore, the interactive nature of compound 2 with a model serum carrier protein bovine serum albumin (BSA) was studied using a multi-spectroscopic approach which provided an insight into the nature and extent of binding, conformational changes and the quenching of amino acid residues of the protein.