Posterior Cruciate Ligament Resection and Varus Correction in Total Knee Arthroplasty: A Study Using Computer-Assisted Surgery

Effect of Posterior Cruciate Ligament Resection on Gap Balancing in Robot-assisted Total Knee Arthroplasty

OBJECTIVE

Retention or sacrifice of the posterior cruciate ligament (PCL) is one of the most controversial issues while performing total knee arthroplasty (TKA). This study aimed to evaluate the impact of PCL resection on flexion-extension gaps, femoral component rotation, and bone resection amounts during robot-assisted TKA.

METHODS

This prospective study included 40 patients with knee osteoarthritis who underwent robot-assisted posterior-stabilized (PS) TKA between September 2021 and February 2022. Of the patients, 75% were women (30/40) with a mean age and BMI of 72.6 years and 27.4 kg/m2, respectively. The guidance module and camera stand assembly were used to capture gaps before and after PCL resection. Measurements of femoral component rotation and bone resection amounts were made in cruciate-retaining (CR) TKA mode and PS-TKA mode.

RESULTS

After PCL resection, the mean change in the medial and lateral compartments of flexion gaps increased by 2.0 and 0.6 mm, respectively (p < 0.001). Compared with the CR-TKA mode group, the bone resection amounts of the medial posterior condyle and the lateral posterior condyle in the PS-TKA mode group decreased by 2.0 ± 1.1 and 1.1 ± 1.1 mm, respectively, and the external rotation of the femoral prosthesis relative to the posterior condylar axis and trans-epicondylar line was reduced by 1.0° ± 1.3° and 1.2° ± 1.6°, respectively (p < 0.001).

CONCLUSION

The release of the PCL did not affect the extension gap, but significantly increased the flexion gap. Moreover, the increases in the medial flexion gap were greater than those of the lateral flexion gap. After PCL resection, less external rotation of the femoral prosthesis and fewer bone cuts of the posterior femur were needed in PS-TKA.

Impact of Structural Compliance of a Six Degree of Freedom Joint Simulator on Virtual Ligament Force Calculation in Total Knee Endoprosthesis Testing

The AMTI VIVO™ six degree of freedom joint simulator allows reproducible preclinical testing of joint endoprostheses under specific kinematic and loading conditions. When testing total knee endoprosthesis, the articulating femoral and tibial components are each mounted on an actuator with two and four degrees of freedom, respectively. To approximate realistic physiological conditions with respect to soft tissues, the joint simulator features an integrated virtual ligament model that calculates the restoring forces of the ligament apparatus to be applied by the actuators. During joint motion, the locations of the ligament insertion points are calculated depending on both actuators' coordinates. In the present study, we demonstrate that unintended elastic deformations of the actuators due to the specifically high contact forces in the artificial knee joint have a considerable impact on the calculated ligament forces. This study aims to investigate the effect of this structural compliance on experimental results. While the built-in algorithm for calculating the ligament forces cannot be altered by the user, a reduction of the ligament force deviations due to the elastic deformations could be achieved by preloading the articulating implant components in the reference configuration. As a proof of concept, a knee flexion motion with varying ligament conditions was simulated on the VIVO simulator and compared to data derived from a musculoskeletal multibody model of a total knee endoprosthesis.

Preoperative Factors Predicting the Preservation of the Posterior Cruciate Ligament in Total Knee Arthroplasty

Objective

Predicting the successful preservation of posterior cruciate ligament (PCL) in total knee arthroplasty (TKA) is an important step for preoperative planning to secure the satisfactory outcomes. We aimed to examine the preoperative factors predicting the successful preservation of the PCL in cruciate‐retaining TKA and the outcome of sacrificing the PCL.

Methods

In this retrospective study, we analyzed TKAs consecutively performed by a single surgeon between January 2019 and August 2021 who had been preoperatively planned to undergo implantation of cruciate‐retaining (CR) prostheses. The outcome of the current study was whether the PCL was retained or sacrificed. Anterior‐stabilized (AS) tibial bearings when the PCL was sacrificed as needed were used intraoperatively. Age, sex, body mass index (BMI), and preoperative diagnosis from the patients' medical records were obtained. The medial‐lateral width of epicondyle (MLW), the medial posterior condyle height (MPCH), the lateral posterior condyle height (LPCH), the ratio of MLW and MPCH, the ratio of MLW and LPCH, the Insall–Salvati index, and the severity of the varus or valgus deformity were measured using preoperative radiographs. Univariate and multivariate regression were fitted to assess the association of these factors with the successful retention of PCL. To examine the influence of sacrifice of the PCL on the surgical procedure, the size of the tibial and femoral components, the thickness of the polyethylene insert, and the rate of patella replacement between the CR group and AS group were also compared using t tests or chi‐square tests.

Results

Among 307 TKAs included, PCL was sacrificed with concurrent use of AS prostheses in 89 (29.0%) procedures. Knees with rheumatoid arthritis (P < 0.01), lower Insall–Salvati index (P < 0.01), and more severe varus deformity (P = 0.011) were at a higher risk of sacrificing the PCL intraoperatively. There was no significant difference in age, sex, BMI, MLW, MPCH, LPCH, ratio of MLW and MPCH, ratio of MLW and LPCH, size of the tibial and femoral components, or replacement of the patella between the CR and AS groups. Converting from CR to AS was associated with a higher risk of using a thicker polyethylene insert (P < 0.01).

Conclusion

Rheumatoid arthritis, lower Insall–Salvati index, and more severe varus deformity were associated with an increased risk of sacrificing the PCL in TKAs planned to undergo implantation CR prostheses. Converting to AS tibial bearing may result in a thicker polyethylene insert. These factors should be carefully considered for the appropriate selection of prosthesis type preoperatively.