Are current total knee arthroplasty implants designed to restore normal trochlear groove anatomy?

Medial orientation of the trochlear groove is a strong indicator of high-grade trochlear dysplasia

PURPOSE

The objective is to evaluate the orientation of the trochlear groove in patients with objective patellar instability (OPI) compared to a control group. The hypothesis is that the trochlear groove angle (TGA) is correlated with the severity of the trochlear dysplasia.

METHODS

From 2019 to 2023, magnetic resonance imaging of 82 knees with OPI were compared with 82 control knees. TGA quantified the angle between the femoral anatomical axis and the trochlear groove. The intraclass correlation coefficient for TGA was evaluated. Central spur in the sagittal plane (CSSP) and cranial trochlear orientation (CTO) angle were also measured. TGA, CSSP and CTO were compared between the two groups. A TGA subgroup analysis separating the OPI group into low-grade (CSSP < 5 mm or negative CTO) and high-grade dysplasia (CSSP ≥ 5 mm or positive CTO) was also performed.

RESULTS

A significant difference (p < 0.001) was found between the TGA of the OPI group (mean [SD], 11.3 [3.7]°) and the control group (4.2 [2.5]°). TGA for patients with high-grade dysplasia (11.9 [3.8]°) was significantly higher than patients with low-grade dysplasia (9.6 [3.9]°).

CONCLUSION

Patients with OPI have a TGA of 11°, compared to the control group, which exhibits a TGA of 4°. The femoral mechanical axis can be considered an appropriate threshold for separating these two groups. Furthermore, TGA is correlated with the severity of dysplasia.

STUDY DESIGN

Case-control study.

LEVEL OF EVIDENCE

Level III.

Restoration of the anterior compartment after robotic total knee arthroplasty significantly improves functional outcome and range of motion at 1 year

PURPOSE

This study aims to assess the functional outcomes based on restoring the anterior compartment after total knee arthroplasty (TKA).

METHODS

This retrospective study included 96 primary TKAs performed between 2021 and 2022. Functional positioning principles were applied using an image-based robotic-assisted system. The mean age was 69.2 ± 7.9 years. Knee Society Score (KSS), Kujala score, Forgotten Joint Score (FJS) and knee flexion were collected preoperatively and at 1 year. The depth difference between native and prosthetic trochlea was measured to assess anterior compartment restoration at full extension, 30°, 70° and 90° flexion. The global anterior compartment restoration combined the anterior compartment restoration and the patellar thickness restoration.

RESULTS

The trochlear offset was mostly understuffed after TKA compared to the native anatomy, mainly for medial and lateral condyles at 30° and 70° of flexion. The global anterior compartment restoration was understuffed in full extension (-0.7 mm ± 2), at 30° (-4.4 mm ± 2) and 70° of flexion (-3.6 mm ± 2.5). At 90°, the global anterior compartment restoration was overstuffed (2.2 mm ± 1.8). Functional scores were not significantly influenced by the anterior compartment stuffing at 0° and 30° (n.s.). The anterior compartment overstuffing at 70° and 90° was associated with decreased KSS function score (p = 0.009) and flexion (p = 0.04).

CONCLUSION

Moderate anterior understuffing was frequently observed after TKA performed with functional positioning and an image-based robotic-assisted system. This understuffing did not influence the functional outcomes. The overstuffing of the anterior compartment led to a reduction in KSS function score and flexion measurements at 1 year.

LEVEL OF EVIDENCE

Level III, retrospective cohort study.

Variations in Trochlear Morphology of Contemporary and Legacy Total Knee Arthroplasty Prostheses: A Review of 22 Designs

BACKGROUND

The morphology of the trochlear compartment of total knee arthroplasty (TKA) prostheses is a major determinant of postoperative patello-femoral kinematics, particularly with unresurfaced patellae. The objective of this study was to quantify and compare the trochlear morphology of a large series of contemporary and legacy TKA designs.

METHODS

The 3-dimensional surface models of 22 femoral components (13 contemporary and 9 legacy) were created using high-resolution laser scanning. The trochlear profile of each component was analyzed from proximal to distal in 15° increments around the trochlear axis. In each profile, the following variables were measured: sulcus angle, medio-lateral deviation of the sulcus, the height and width of the facets, and the trochlear groove orientation.

RESULTS

In the contemporary group, the sulcus angle decreased progressively along the trochlear arc to varying degrees, except for 2 symmetrical designs, whereas the sulcus angle of the legacy designs showed considerable variability. The height of the medial facet was very strongly correlated with that of the lateral facet in the contemporary group (R2 = 0.89), whereas the correlation was weak for the legacy designs (R2 = 0.36). Moreover, the trochlear sulcus deviated laterally from distal to proximal in 10 contemporary designs and 7 legacy designs, resulting in a trochlear groove orientation of 4.2 to 11.1° and 4.3 to 10.5°, respectively. In the remaining 5 designs (3 contemporary and 2 legacy), the sulcus was vertical.

CONCLUSIONS

There is more consistency in trochlear morphology of contemporary TKA designs compared to that of legacy designs, yet there are still large variations between different designs.

Differences in Trochlear Morphology of a New Femoral Component Designed for Kinematic Alignment from a Mechanical Alignment Design

Because kinematic alignment (KA) aligns femoral components in greater valgus and with less external rotation than mechanical alignment (MA), the trochlear groove of an MA design used in KA is medialized, which can lead to complications. Hence, a KA design has emerged. In this study, our primary objective was to quantify differences in trochlear morphology between the KA design and the MA design from which the KA design evolved. The KA and MA designs were aligned in KA on ten 3D femur-cartilage models. Dependent variables describing the morphology of the trochlea along the anterior flange, which extends proximal to the native trochlea, and along the arc length of the native trochlea, were determined, as was flange coverage. Along the anterior flange, the KA groove was significantly lateral proximally by 10 mm and was significantly wider proximally by 5 mm compared to the MA design (p < 0.0001). Along the arc length of the native trochlea, the KA groove was significantly lateral to the MA design by 4.3 mm proximally (p ≤ 0.0001) and was significantly wider proximally by 19 mm than the MA design. The KA design reduced lateral under-coverage of the flange from 4 mm to 2 mm (p < 0.0001). The KA design potentially mitigates risk of patellofemoral complications by lateralizing and widening the groove to avoid medializing the patella for wide variations in the lateral distal femoral angle, and by widening the flange laterally to reduce under-coverage. This information enables clinicians to make informed decisions regarding use of the KA design.

Deep Learning for Automated Measurement of Patellofemoral Anatomic Landmarks

BACKGROUND

Patellofemoral anatomy has not been well characterized. Applying deep learning to automatically measure knee anatomy can provide a better understanding of anatomy, which can be a key factor in improving outcomes.

METHODS

483 total patients with knee CT imaging (April 2017-May 2022) from 6 centers were selected from a cohort scheduled for knee arthroplasty and a cohort with healthy knee anatomy. A total of 7 patellofemoral landmarks were annotated on 14,652 images and approved by a senior musculoskeletal radiologist. A two-stage deep learning model was trained to predict landmark coordinates using a modified ResNet50 architecture initialized with self-supervised learning pretrained weights on RadImageNet. Landmark predictions were evaluated with mean absolute error, and derived patellofemoral measurements were analyzed with Bland-Altman plots. Statistical significance of measurements was assessed by paired t-tests.

RESULTS

Mean absolute error between predicted and ground truth landmark coordinates was 0.20/0.26 cm in the healthy/arthroplasty cohort. Four knee parameters were calculated, including transepicondylar axis length, transepicondylar-posterior femur axis angle, trochlear medial asymmetry, and sulcus angle. There were no statistically significant parameter differences (p > 0.05) between predicted and ground truth measurements in both cohorts, except for the healthy cohort sulcus angle.

CONCLUSION

Our model accurately identifies key trochlear landmarks with ~0.20-0.26 cm accuracy and produces human-comparable measurements on both healthy and pathological knees. This work represents the first deep learning regression model for automated patellofemoral annotation trained on both physiologic and pathologic CT imaging at this scale. This novel model can enhance our ability to analyze the anatomy of the patellofemoral compartment at scale.

High femoral anteversion in osteoarthritic knees, particularly for severe valgus deformity

Objective

Increased femoral anteversion (FA) has been correlated with less varus deformities in osteoarthritic (OA) knees, but the relationship between FA and the degree of valgus deformity in osteoarthritic (OA) knees is still largely unknown. We aimed to thoroughly analyze the distribution of FA in relation to varus or valgus deformities of the lower extremity in OA knees, and to further clarify the relationship between FA and trochlear morphology.

Methods

235 lower extremities with OA knees were divided into five groups according to the mechanical tibiofemoral angle: excessive valgus (< − 10°), moderate valgus (− 10° to − 3°), neutral (− 3° to 3°), moderate varus (3° to 10°), and excessive varus (> 10°). FA (measured using the posterior condylar axis [pFA] and the transepicondylar axis [tFA]) was measured, and the relationships of FA to the mechanical tibiofemoral angle and femoral trochlear morphology were identified.

Results

Excessive FA (pFA ≥ 20°) was observed in 30.2% of all patients and in 58.8% of patients in the excessive valgus group. pFA showed a strong correlation with mechanical tibiofemoral angle (p = 0.018). Both the pFA and the tFA of patients in the excessive valgus group were greater than those in other four groups (all p ≤ 0.037). There were significant correlations between tFA and trochlear parameters, including the sulcus angle (SA), lateral trochlear slope (LTS), and medial trochlear slope (MTS) (all p ≤  0.028).

Conclusion

High FA is prevalent, particularly in severe valgus knees, and FA is significantly related to the femoral trochlear morphology in OA knees. With the aim of improving the patellofemoral prognosis and complications, high FA should be considered during total knee arthroplasty.

Differences in Trochlear Morphology from Native Using a Femoral Component Interfaced with an Anatomical Patellar Prosthesis in Kinematic Alignment and Mechanical Alignment

Patellofemoral complications following total knee arthroplasty can be traced in part to alignment of the femoral component. Kinematic alignment (KA) and mechanical alignment (MA) use the same femoral component but align the component differently. Our objective was to determine differences in trochlear morphology from native for a femoral component interfaced with an anatomical patellar prosthesis in KA and MA. Ten three-dimensional femur-cartilage models were created by combining computed tomography and laser scans of native human cadaveric femurs free of skeletal abnormalities. The femoral component was positioned using KA and MA. Measurements of the prosthetic and native trochlea were made along the arc length of the native trochlear groove and differences from native were computed for the medial-lateral and radial locations of the groove and sulcus angle. Mean medial-lateral locations of the prosthetic groove were within 1.5 and 3.5 mm of native for KA and MA, respectively. Mean radial locations of the prosthetic groove were as large as 5 mm less than native for KA and differences were greater for MA. Sulcus angles of the prosthetic trochlea were 10 degrees steeper proximally, and 10 degrees flatter distally than native for both KA and MA. Largest differences from native occurred for radial locations and sulcus angles for both KA and MA. The consistency of these results with those of other fundamentally different designs which use a modified dome (i.e., sombrero hat) patellar prosthesis highlights the need to reassess the design of the prosthetic trochlea on the part of multiple manufacturers worldwide.

Intraoperative analysis of patellofemoral joint morphology before and after total knee arthroplasty

Background

Patellofemoral problems after total knee arthroplast (TKA) are frequent and often associated with a change in the geometry of the trochlear groove.

Objective

The present study aimed to analyze the feasibility of intraoperative examination of the patellofemoral joint geometry before and after the implantation of bicondylar total knee replacements without exposing the patient to radiation.

Material and methods

The patellofemoral joint morphology geometries of 33 patients before and after implantation of a bicondylar total knee replacement was intraoperatively analyzed using a digital scanning method. Femoral surface geometries were extracted from intraoperatively recorded tactile scanning data using an in-house algorithm. The geometries were then characterized by sulcus height, medial femoral condyle height and lateral femoral condyle height.

Results

Our preliminary results show that these key geometric parameters are only partially restored after TKA leading to a distinctly different shaped profile of the anterior distal femur. Maximum and minimum mean differences in sulcus height, medial femoral condyle height, and lateral femoral condyle height before and after surgery were 2.00 mm/−3.06 mm, 2.51 mm/−6.25 mm and 2.74 mm/−3.58 mm, respectively.

Conclusion

A new method for intraoperative analysis of the patellofemoral joint morphology before and after TKA without radiation exposure was developed and utilized. Even with the use of modern total knee designs, the patellofemoral articulation is considerably changed postoperatively as quantified by the key parameters of sulcus height, medial femoral condyle height, and lateral femoral condyle height. This may result in altered knee biomechanics and might explain persistent patellofemoral disorders, which are often reported by patients after TKA.

An automatic measurement system of distal femur morphological parameters using 3D slicer software

In the field of joint surgery, the computer-aided design of knee prostheses suitable for the Chinese population requires a large quantity of anatomical knee data. In this study, we propose a new method that uses 3D Slicer software to automatically measure the morphological parameters of the distal femur. First, 141 femur samples were segmented from CT data to establish the femoral shape library. Next, balanced iterative reducing and clustering using hierarchies (BIRCH) combined with iterative closest point (ICP) and generalised procrustes analysis (GPA) were used to achieve fast registration of the femur samples. The statistical model was automatically calculated from the registered femur samples, and an orthopaedic surgeon marked the points on the statistical model. Finally, we developed an automatic measurement system using 3D Slicer software, and a deformable model matching method was applied to establish the point correspondence between the statistical model and the other samples. By matching points on the statistical model to corresponding points in other samples, we measured all other samples. We marked six points and measured eight parameters. We evaluated the performance of automatic matching by comparing the points marked manually with those matched automatically and verified the accuracy of the system by comparing the manual and automatic measurement results. The results indicated that the average error of the automatic matching points was 1.03 mm, and the average length error and average angle error measured automatically by the system were 0.37 mm and 0.63°, respectively. These errors were smaller than the intra-rater and inter-rater errors measured manually by two different surgeons, which showed that the accuracy of our automatic method was high. Taken together, this study established an accurate and automatic measurement system for the distal femur based on the secondary development of 3D Slicer software to assist orthopaedic surgeons in completing the measurements of big data and further promote the improved design of Chinese-specific knee prostheses.

The sagittal geometry of the trochlear groove could be described as a circle: an intraoperative assessment with navigation

PURPOSE

The aim of this study was to describe the sagittal geometry of the trochlear groove in patients who underwent primary TKA, based on intraoperative data acquired with a navigation system.

METHODS

Intraoperative navigation data were collected from 110 patients. All operations were guided by a non-image-based navigation system (BLU-IGS, Orthokey Italia Srl). The trochlear groove has been described on the three anatomical planes; in particular, on the sagittal plane the hypothesis has been verified that the acquired points are referable to a circle. Using the data collected during intraoperative navigation, possible correlation between the radius of the trochlear groove and other femur dimension (length, AP dimension) was analyzed; the orientation of the trochlear sulcus with respect to the mechanical axis and the posterior condyle axis was analyzed too, searching for possible correlation between groove alignment (frontal and axial) or groove radius and the hip-knee-ankle (HKA).

RESULTS

The average radius of curvature of the femoral trochlea was 25.5 ± 5.6 mm; the difference was not statistically significant between the men and women (n.s. p value). No correlation was found between the trochlear groove radius and the femur length (r = - 0.02) or the HKA-phenotypes (r = 0.03) and between the groove alignment and HKA-phenotypes. On axial plane, the trochlear groove was 3.2° ± 4.3° externally rotated, with respect to the posterior condylar axis; on frontal plane, the trochlear groove was 3.9° ± 5.3° externally rotated, with respect to the mechanical axis. In both cases, no statistically significant differences were found between male and female and between left and right limb (p > 0.05).

CONCLUSION

The present study shows that the sagittal plane geometry of the femoral trochlea in patients affected by osteoarthritis could be described accurately as a circle. The acquisition of the trochlear morphology intraoperatively can lead to more anatomically shape definition, to investigate deeper its radius of curvature and geometry. Trochlear shape could be used as landmarks for femoral component positioning, thus customizing the implant design, optimize the outcomes and improving anterior knee pain after TKA.

LEVEL OF EVIDENCE

IV.

Three-dimensional morphology of the distal femur based on surgical epicondylar axis in the normal elderly population

BACKGROUND

We aimed to analyze the surface morphology of the distal femur in three dimensions for the healthy elderly, based on the concept that the surgical epicondylar axis (SEA) is a better surrogate for the flexion-extension axis of the knee joint.

METHODS

We studied 77 healthy elderly volunteers (40 males and 37 females; age, 68 ± 6 years). The medial and lateral contact lines were calculated three-dimensionally, using the highest points of the medial and lateral condyles in 201 cross-sectional planes around the SEA (every 1°, -60° (hyperextension) to 140° (flexion)). A piecewise fitting function consisting of two linear segments was applied to detect the inflection point of the constant radii in the sagittal plane. The main assessment parameters were knee flexion angle at the inflection point of the radius (inflection angle), mean radius from 0° to the inflection angle (constant radius), and coronal tilt angle of the contact line.

RESULTS

The inflection angles, constant radii, and coronal tilt angles were 78.2 ± 8.6°, 26.1 ± 2.3 mm, and -0.6 ± 3.2° and 65.6 ± 9.2°, 23.9 ± 2.2 mm, and 6.2 ± 3.2° in the medial and lateral condyles, respectively (all, P < 0.001). The coronal alignment was 88.7 ± 2.2°.

CONCLUSIONS

The medial and lateral femoral condyles showed asymmetrical morphologies with the almost 'constant' radius of sagittal curvature from 0° to around 80° and 65° of knee flexion, respectively.

Modern total knee arthroplasty designs do not reliably replicate anterior femoral morphology

PURPOSE

Biomechanical studies suggest that PF tracking is not reliably restored to physiological values in TKA despite surgical technique optimization. A clinical observation is that current TKA designs may not replicate anterior femoral offset. The aim was to examine the intraoperative resection thicknesses of the anterior femoral condyles during TKA and correlate these findings relative to modern prostheses.

METHODS

This was a retrospective analysis of 199 patients who underwent 233 TKAs using a single implant design with measured anterior femoral condylar resection thicknesses. The aim was to restore posterior condylar offset whilst minimizing overstuffing of the anterior compartment of the knee by choosing the smallest prosthesis to allow for the maximal anterior resection as close to the cortex without inducing notching. Prosthetic measurements from 7 commonly used TKAs were collected by analysis of 3D models of median sized explants.

RESULTS

An average of 7.9 mm (SD 2.5 mm, range 2-16.5 mm) and 11.5 mm (SD 2.5 mm, range 2-21 mm) was resected from the medial and lateral aspects of the anterior femur, respectively. The average anterior flange thickness for the prosthesis data set was 6.6 mm (SD 0.6 mm, range 6.1-7.9 mm) medially and 7.6 mm (SD 0.7 mm, range 6.8-9.0 mm) laterally. Comparison across patients who received the median prosthesis size of 5 (SD 1.3, range 2-8) was inadequately restored by 1.4 mm (p < 0.00001) medially and 3.4 mm (p < 0.00001) laterally.

CONCLUSION

Host anatomy is not routinely restored during TKA. The surgical teaching to aim for an anterior femoral osteotomy close to the anterior cortex will result in understuffing of the PFJ and based on current prosthesis designs, the risk of overstuffing is not as significant as once believed. Future prostheses and surgical techniques should aim to restore not only posterior femoral but also anterior femoral offset.

LEVEL OF EVIDENCE

IV, Case series.

Kinematic alignment more closely restores the groove location and the sulcus angle of the native trochlea than mechanical alignment: implications for prosthetic design

PURPOSE

Kinematic alignment (KA) and mechanical alignment (MA) position the prosthetic trochlea that guides patellar tracking differently. The present study determined whether KA or MA more closely restores the groove location and sulcus angle of the prosthetic trochlea to the native trochlea for three femoral component designs.

METHODS

Ten 3D femur-cartilage models were created by combining computer tomographic (CT) and laser scans of native human cadaveric femurs. Three femoral component designs were positioned using KA and MA. Measurements of the prosthetic and native trochlea were made along the arc length of the native trochlear groove. The alignment technique with the smaller absolute difference between prosthetic and native for the medial-lateral and radial locations of the groove and sulcus angle of the trochlea more closely restored the native trochlea.

RESULTS

For three femoral component designs, KA more closely restored to native the mean medial-lateral location (p = 0.0033 to < 0.0001) and mean radial location (p = 0.0150 to < 0.0001) than MA. For two femoral component designs, KA more closely restored to native the mean sulcus angle (p = 0.0326 to 0.0006) than MA. However, the differences in the mean sulcus angles between KA and MA were less than 2° for all three designs.

CONCLUSION

KA more closely restored the native trochlea, which explains why the reported risk of patellofemoral complications for KA is not higher than MA according to five randomized clinical trials. Small design modifications of the medial-lateral and radial locations and sulcus angle are strategies for restoring the native trochlea. Such modifications might further reduce the risk of patellofemoral complications.

LEVEL OF EVIDENCE

II.

Patellofemoral design enhancements reduce long-term complications of postero-stabilized total knee arthroplasty

PURPOSE

Few studies investigated whether trochlear and patellar design enhancements improve long-term outcomes of total knee arthroplasty (TKA). This study aimed to compare the long-term survival and complication rates of two consecutive generations of the same TKA system with identical tibiofemoral geometry, but different patellofemoral designs.

METHODS

The authors retrieved the records of 93 patients (104 knees) operated with the HLS II system and 116 patients (122 knees) operated with HLS Evolution system. Patients were evaluated preoperatively and at a minimum of 10 years noting all complications. Kaplan-Meier (KM) survival was compared for two endpoints: (1) revision of all components and (2) revision of any component.

RESULTS

From the HLS II series, the incidence of revision of all components was 6.4%, and of any component was 9.8%. From the HLS Evolution series, the incidence of revision of all components was 4.1%, and of any component was 5.1%. Comparing the survival at equivalent follow-up of 14 years, considering revision of all components, the HLS II had higher survival than the HLS Evolution (98.9% vs 95.9%), while considering revision of any component, the HLS II had lower survival than the HLS Evolution (93.0% vs 94.9%). The differences in survival of the two implants were not significant, neither at equivalent follow-up of 14 years (n.s.), nor at maximum follow-up of each cohort (n.s.). The complication rate was higher for the HLS II series compared to the HLS Evolution (28% vs 12%, p = 0.009), but patellofemoral complications were not more frequent (8% vs 6%, n.s.).

CONCLUSIONS

Though the differences in survival of the two implants were not significant, conflicting findings are observed due to partial revisions for patellar fractures (5 in the HLS II series and 1 in the HLS Evolution series) which could be related to patellofemoral design enhancements. This study highlights the importance of patello-femoral geometry, which is often overlooked in TKA.

LEVEL OF EVIDENCE

Retrospective comparative study, Level III.

Surgical technique in patellofemoral arthroplasty

Patellofemoral arthroplasty (PFA) has seen its role validated over the last decade as a treatment for severe Iwano III or IV patellofemoral osteoarthritis (PFOA). The ideal indication is PFOA with femoral trochlear dysplasia. The accumulation of data on factors influencing the likelihood of PFA failure or success when using first- or second-generation implants has led to design changes, which have been incorporated into modern third-generation implants. These implants are positioned using anatomic cuts, with instrumentation kits that ensure accurate and reproducible alignment. Their design corrects the femoral trochlear dysplasia. Refinements in the indications of PFA, together with advances in prosthetic kinematics and improved understanding of the surgical technique, have strengthened the role for PFA. Although either a lateral or a medial approach can be used, the lateral approach deserves preference. Proper orientation of the femoral and patellar implants is crucial and can be achieved in an accurate and reproducible manner. Orientation of the coronal femoral cut is the only modifiable variable. The cut should be performed with the knee in neutral rotation to minimise both the tibial tuberosity-trochlear groove distance and the amount of extensor apparatus valgus. In the coronal plane, the femoral component must be positioned in valgus, to align the distal part of the trochlear implant with the lateral condylar cartilage. Medial positioning of the patellar component finalises the match between the femur and the patella. This coronal alignment of the two components promotes patellar engagement at the beginning of knee flexion. Thus, the technique brings the trochlea towards the patella and the patella towards the trochlea, thereby ensuring optimal patellofemoral tracking and ensuring a good final outcome. When these requirements are met, the functional and radiographic outcomes are predictable, of good quality, and sustained over time, provided the patient remains free of tibio-femoral osteoarthritis.

Gender differences in knee morphology and the prospects for implant design in total knee replacement

BACKGROUND

Morphological differences between female and male knees have been reported in the literature, which led to the development of so-called gender-specific implants. However, detailed morphological descriptions covering the entire joint are rare and little is known regarding whether gender differences are real sexual dimorphisms or can be explained by overall differences in size.

METHODS

We comprehensively analysed knee morphology using 33 features of the femur and 21 features of the tibia to quantify knee shape. The landmark recognition and feature extraction based on three-dimensional surface data were fully automatically applied to 412 pathological (248 female and 164 male) knees undergoing total knee arthroplasty. Subsequently, an exploratory statistical analysis was performed and linear correlation analysis was used to investigate normalization factors and gender-specific differences.

RESULTS

Statistically significant differences between genders were observed. These were pronounced for distance measurements and negligible for angular (relative) measurements. Female knees were significantly narrower at the same depth compared to male knees. The correlation analysis showed that linear correlations were higher for distance measurements defined in the same direction. After normalizing the distance features according to overall dimensions in the direction of their definition, gender-specific differences disappeared or were smaller than the related confidence intervals.

CONCLUSIONS

Implants should not be linearly scaled according to one dimension. Instead, features in medial/lateral and anterior/posterior directions should be normalized separately (non-isotropic scaling). However, large inter-individual variations of the features remain after normalization, suggesting that patient-specific design solutions are required for an improved implant design, regardless of gender.

Differences in trochlear parameters between native and prosthetic kinematically or mechanically aligned knees

INTRODUCTION

Kinematic (KA) and mechanical (MA) alignment techniques are two different philosophies of implant positioning that use the same TKA implants. This might generate differences in the resulting prosthetic trochleae parameters between the two techniques of alignment. Our study aim was to test the following hypotheses : (1) mechanically or kinematically aligned femoral implant understuffs the native trochlear articular surface and poorly restores the native groove orientation, and (2) the orientation of the prosthetic trochlear groove and trochlear fill are different between MA and KA.

METHODS

Three-dimensional models of the femur were made from segmentation of preoperative Magnetic Resonance Imaging scans (MRIs) of ten subjects with isolated medial tibiofemoral osteoarthritis. In-house planning and analysis software kinematically and mechanically aligned a modern cruciate retaining femoral component and determined differences in parameters of the trochlear fit between native and prosthetic trochleae, and between KA and MA prosthetic trochleae.

RESULTS

The MA prosthetic trochleae did not fill (understuffed) the entire length of the native medial facet and the proximal 70% of the native groove and lateral facet, and oriented the trochleae groove 8° more valgus than native. The KA prosthetic trochleae understuffed the proximal 70% of the native trochleae, and had a groove 6° more valgus than native. The KA trochleae understuffed the medial facet distally and oriented the groove 2° less valgus and 3° more internally rotated than the MA trochleae.

CONCLUSION

MA and KA prosthetic trochleae substantially understuff and create a prosthetic groove more valgus compared to native trochlear anatomy, and they also differed between each other regarding trochleae stuffing and groove alignment. Although randomized trials have not shown differences in patellofemoral complications between KA and MA, a femoral component designed specifically for KA that more closely restores the native trochlear anatomy might improve patient reported satisfaction and function.

LEVEL OF EVIDENCE

Level 2 controlled laboratory study.

The need for secondary resurfacing is affected by trochlear height in total knee arthroplasty

PURPOSE

The purpose of the study was to compare the rate of secondary resurfacing in a consecutive series of five different total knee arthroplasty (TKA) systems. It was our hypothesis that different TKA design features such as sulcus angle or trochlear height influence the rate of secondary resurfacing.

METHODS

A retrospective study was performed on data from patients who underwent TKA without primary patellar resurfacing from 2004 to 2012 in an university-affiliated hospital. The study cohort included 784 TKA patients (m:f = 302:482, mean age at surgery ± SD 71 ± 10). Five different cruciate-retaining TKA systems were used consecutively (Group A, Triathlon, Stryker, Switzerland (n = 296), Group B, PFC Sigma, DepuySynthes, Switzerland (n = 215), Group C, LCS, DepuySynthes, Switzerland (n = 81), Group D, Balansys, Mathys, Switzerland (n = 128), Group E, Duracon, Stryker, Switzerland (n = 64)). Data were retrospectively obtained from hospital archives. Patients demographics, age at surgery, type of TKA were noted. In addition, TKA component position was assessed on radiographs with respect to "The knee society total knee arthroplasty roentgenographic evaluation and scoring system" (TKA-RESS). Pearson Chi-square test was used to compare differences between groups (p < 0.05). There were no significant differences between the groups in terms of age, gender, and radiological outcomes.

RESULTS

Twenty-six of 784 patients (3.3 %) underwent secondary resurfacing due to patellofemoral pain. In group A 4/296 patients (1.4 %), in group B 15/215 patients (7 %), in group C 5/81 patients (6.2 %), in group D 1/128 patients (0.8 %), in group E 1/64 patients (1.6 %) underwent secondary patellar resurfacing during follow-up. Significantly higher rates of secondary patellar resurfacing were seen in groups B and C when compared to the others (p < 0.001). It was found that the trochlear height in these TKA was higher than in the others.

CONCLUSIONS

Based on the findings of this study, trochlear height influences the need for secondary patellar resurfacing. The resurfacing rate ranged from 1 to 7 %, with the highest rate in the PFC Sigma TKA.

LEVEL OF EVIDENCE

Therapeutic study, Level III.

Differences in Trochlear Surface Damage and Wear Between Three Different Total Knee Arthroplasty Designs

INTRODUCTION

Trochlear design plays a role in patellofemoral kinematics. Little is known regarding differences in the contact properties between modern designs. The purpose of the present study was to analyze patellofemoral joint contact by identifying areas of joint surface damage and wear in retrieved femoral components of 3 modern designs.

MATERIALS

Eighteen retrieved femoral components featuring 3 different modern designs (Triathlon, SIGMA, and GENESIS II) were matched based on time-in-vivo, age, gender, and body mass index. Trochlear wear and surface damage were assessed using visual inspection, light microscopy, and light profilometry.

RESULTS

Visual inspection of the femoral components showed evidence of surface damage in all implant types. No significant differences between the groups were found with respect to surface damage and wear on visual inspection. Light profilometry of retrieved components showed that retrieved Triathlon (P = .002) and SIGMA (P = .009) components were significantly rougher than the corresponding reference components. The GENESIS II retrieved components were not substantially rougher than the reference components (P = .48). Light profilometry analysis showed significantly increased roughness of retrieved SIGMA components compared with Triathlon or GENESIS II components, particularly in the proximal trochlear groove and the medial trochlea.

CONCLUSION

As the volume and patient demands for total knee arthroplasty increase, a greater understanding of the patellofemoral joint is warranted. Patellofemoral kinematics can have an effect on the surface characteristics of total knee arthroplasty components. Retrieved SIGMA components appeared to have increased roughness compared with Triathlon or GENESIS II components. The etiology and long-term effects of increased trochlear roughness require further investigation.

Standard versus physiologic bone preparation in total knee arthroplasty and the effect on joint space opening

BACKGROUND

Total knee arthroplasty is an effective treatment for osteoarthritis. Restoration of physiologic varus alignment may restore the native soft tissue tension and improve outcomes.

METHODS

Six paired fresh-frozen knee specimens were used to perform total knee arthroplastys. The left and right sides of were randomly assigned to have either a physiologic alignment cut or a standard of care neutral alignment bony cut prior to the implantation. Loads of 100 and 200N were applied at 0, 30, 60, and 90° of flexion and the magnitude of the medial and lateral compartment distraction was measured. The loads were applied with the knee specimen intact and post arthroplasty.

FINDINGS

The physiologic alignment had no difference between medial and lateral gaps at either load. With 100N of load the physiologic alignment had a greater gap at 90° than at full extension while the standard alignment had significantly more gap at 60° of flexion than full extension. The physiologic alignment had a significantly greater gap with the implant compared to the intact condition at both loads. The standard alignment had no significant difference in overall gap between the implant and intact condition with any load.

INTERPRETATION

Although performing a physiologic aligned TKA resulted in medial-lateral soft tissue balance, the flexion gap was found to have greater magnitude than the intact knee. Notably, a neutral aligned TKA was found to be balanced, but also was found to recreate the intact knee flexion gaps. These results suggest that coronal plane stability can be achieved with physiologic alignment objectives, but the clinician needs to be aware of the potential to have greater laxity than the intact and neutral alignment surgical objectives.

Alignment options for total knee arthroplasty: A systematic review

In spite of improvements in implant designs and surgical precision, functional outcomes of mechanically aligned total knee arthroplasty (MA TKA) have plateaued. This suggests probable technical intrinsic limitations that few alternate more anatomical recently promoted surgical techniques are trying to solve. This review aims at (1) classifying the different options to frontally align TKA implants, (2) at comparing their safety and efficacy with the one from MA TKAs, therefore answering the following questions: does alternative techniques to position TKA improve functional outcomes of TKA (question 1)? Is there any pathoanatomy not suitable for kinematic implantation of a TKA (question 2)? A systematic review of the existing literature utilizing PubMed and Google Scholar search engines was performed in February 2017. Only studies published in peer-reviewed journals over the last ten years in either English or French were reviewed. We identified 569 reports, of which 13 met our eligibility criteria. Four alternative techniques to position a TKA are challenging the traditional MA technique: anatomic (AA), adjusted mechanical (aMA), kinematic (KA), and restricted kinematic (rKA) alignment techniques. Regarding osteoarthritic patients with slight to mid constitutional knee frontal deformity, the KA technique enables a faster recovery and generally generates higher functional TKA outcomes than the MA technique. Kinematic alignment for TKA is a new attractive technique for TKA at early to mid-term, but need longer follow-up in order to assess its true value. It is probable that some forms of pathoanatomy might affect longer-term clinical outcomes of KA TKA and make the rKA technique or additional surgical corrections (realignment osteotomy, retinacular ligament reconstruction etc.) relevant for this sub-group of patients. Longer follow-up is needed to define the best indication of each alternative surgical technique for TKA. Level I for question 1 (systematic review of Level I studies), level 4 for question 2.

Mechanical alignment technique for TKA: Are there intrinsic technical limitations?

BACKGROUND

Mechanically aligned (MA) total knee arthroplasty (TKA) is affected by disappointing functional outcomes in spite of the recent improvements in surgical precision and implant designs. This might suggest the existence of intrinsic technical limitations. Our study aims to compare the prosthetic and native trochlear articular surfaces and to estimate the extent of collateral ligament imbalance, which is technically uncorrectable by collateral ligament release when TKA implants are mechanically aligned.

STUDY HYPOTHESIS

Conventional MA technique generates a high rate of prosthetic overstuffing of the distal groove, distal lateral trochlear facet and distal lateral femoral condyle (Hypothesis 1), and technically uncorrectable collateral ligament imbalance (hypothesis 2)? Disregarding the distal femoral joint line obliquity (DFJLO) when performing femoral cuts explains distal lateral femoral prosthetic stuffing and uncorrectable imbalance (hypothesis 3)?

METHODS

Twenty patients underwent a conventional MA TKA. Pre-operative MRI-based 3D knee models were generated and MA TKA was simulated. Native and prosthetic trochlear articular surfaces were compared using in-house analysis software. Following the automatic determination by the planning software of the size of the extension and flexion gaps, an algorithm was applied to balance the gaps and the frequency and amplitude of technically uncorrectable knee imbalance were estimated.

RESULTS

The conventional MA technique generates a significant slight distal lateral femoral prosthetic overstuffing (mean 0.6mm, 0.8mm, 1.25mm for the most distal lateral facet point, groove, and at the most distal point of lateral femoral condyle, respectively) and a high rate of type 1 and 2 uncorrectable knee imbalance (30% and 40%, respectively). The incidence of distal lateral prosthetic overstuffing (trochlea and condyle) and uncorrectable knee imbalance were strongly to very strongly correlated with the DFJLO (r=0.53 to 0.89).

CONCLUSION

Conventional MA technique for TKA generates frequent lateral distal femoral prosthetic overstuffing and technically uncorrectable knee imbalance secondary to disregarding the DFJLO when adjusting the femoral component frontal and axial rotations, respectively.

LEVEL OF EVIDENCE

level 4.

Morphological classification of the femoral trochlear groove based on a quantitative measurement of computed tomographic models

PURPOSE

This study aimed to investigate the natural morphology of the femoral trochlear groove based on quantitative measurement.

METHODS

Computed tomographic femur models of 50 male and 50 female healthy Chinese adults (30-60 years) were analysed using three-dimensional software. Coaxial cutting planes (15° increments) rotating about the trochlear groove axis from the proximal to distal point were created, followed by the deepest point of the trochlear groove marked at each cross section. The shape, position, and orientation of the trochlear groove were analysed.

RESULTS

The trochlear groove was located laterally relative to the mechanical axis and consisted of the laterally oriented proximal part and medially oriented distal part. Based on the turning points located on different cross sections, the trochlear groove was classified into four types: types 45°, 60°, 75°, and 90°. The mediolateral position relative to the mechanical axis was types 45°, 60°, 75°, and 90°, from the lateral to medial side, while the distal parts of them extended along the same path. The orientation of the trochlear groove was relatively consistent and smooth, which oriented at approximately 1° medially between two adjacent segments, except at approximately 10° medially at the turning point.

CONCLUSION

The trochlear groove tracking varies greatly amongst a population that is mainly categorized into four types. This study may be helpful for better understanding of the natural trochlear groove anatomy, prosthetic design modification, and provide the reference value for studying patellofemoral diseases such as patellar maltracking and trochlear dysplasia.

LEVEL OF EVIDENCE

Prospective study, Level II.

Morphological evaluation of the sagittal plane femoral load-bearing surface in computer-simulated virtual total knee arthroplasty implantation at different flexion angles

PURPOSE

To examine the effect of implantation of the femoral component of a total knee arthroplasty (TKA) system in 0°, 3°, and 6° of flexion on the sagittal plane morphology of the femoral load-bearing surfaces. It was hypothesized that increasing the flexion angle would result in undersizing of the anterior surface without changing the flexion gap.

METHODS

Computer simulation of a TKA using three-dimensional models of 10 healthy knees, matched to three different sized femoral components. Size discrepancy in the sagittal plane anterior, distal, and posterior joint surfaces between the native and prosthetic knees was calculated at 0°, 3°, and 6° of flexion.

RESULTS

The required component size varied with the angle of implantation: 0°, size 3/size 4 (N = 7/3), 3°, size 3 (N = 10); and 6°, size 2/size 3 (N = 4/6). Component undersizing ranged between 4.4-6.3 mm at the anterior lateral surface, with a significant difference between 0° and 6° (p < 0.05), and 1.2-3.5 mm at the anterior medial surface. Component oversizing of the distal surface of the lateral condyle (2.9 mm) and undersizing of the medial surface of the posterior condyle (1.6-2.3 mm) were comparable at all three flexion angles of component implantation.

CONCLUSIONS

Increasing the flexion angle of implantation increased the incidence of using a smaller size of femoral component without significant interference with the flexion gap. However, the effect of a smaller femoral component on undersizing of the anterior surface of the condyle and the impact on the extensor mechanism need to be considered.

Differences between native and prosthetic knees in terms of cross-sectional morphology of the femoral trochlea: a study based on three-dimensional models and virtual total knee arthroplasty

Background

The cross-sectional morphology of the prosthetic knee is crucial to understanding patellar motion and quadriceps strength after total knee arthroplasty. However, few comparative evaluations of the cross-sectional morphology of the femoral trochlea have been performed in the native knee and currently available femoral implants, and the relationship between the trochlear anatomy of prosthetic components and post-operative patellofemoral complications remains unclear. We aimed to investigate the differences in cross-sectional morphology of the femoral trochlea between native knees and prosthetic femoral components.

Methods

Virtual total knee arthroplasty was performed, whereby four different femoral components (medial-pivot, Triathlon, NRG and NexGen) were virtually superimposed onto three-dimensional models of 42 healthy femurs. The following morphological parameters were measured in three cross-sections (0, 45 and 90°) of the femoral trochlea: sulcus height, lateral tilt angle, medial tilt angle and sulcus angle. Only statistically significant differences are described further (p < 0.05).

Results

In the 0° cross-section, sulcus height was smaller in the native knee than in the Triathlon, NRG and NexGen components; all prosthetic components had smaller lateral tilt angles and larger medial tilt angles. In the 45° cross-section, sulcus height was larger in the native knee than in the medial-pivot, Triathlon and NexGen components; both lateral and medial tilt angles were smaller in the prosthetic components. In the 90° cross-section, sulcus height was smaller in the native knee than in the medial-pivot component; all prosthetic components had a larger lateral tilt angle and smaller medial tilt angle. In all cross-sections, the sulcus angle was smaller in the native knee.

Conclusions

The discrepancy between native and prosthetic trochlear geometries suggests altered knee mechanics after total knee arthroplasty, but further cadaveric, computational or fluoroscopic investigations are necessary to clarify the implications of this observation. Our findings can be used to optimize biomechanical guidelines for total knee arthroplasty (patellar resurfacing or non-resurfacing) in Chinese individuals so as to decrease the risk of patellar lateral dislocation, to maintain stability and to optimize extensor kinematics.

Influence of Total Knee Arthroplasty on Patellar Kinematics and Patellofemoral Pressure

BACKGROUND

Patellofemoral complications are one of the main problems after total knee arthroplasty (TKA). The design of the TKA component may affect the patellar biomechanics, which may be associated with this postoperative complication. The purpose of this study was to assess the influence of TKA and prosthesis designs on the patellar kinematics and patellofemoral pressure.

METHODS

Using fresh-frozen cadavers, we measured the patellofemoral pressure, patella offset, and patella tilt in the following 4 conditions: normal knee (patella replacement only), cruciate-retaining TKA, condylar-stabilizing TKA, and posterior-stabilized TKA.

RESULTS

The patellofemoral pressure increased significantly after the cruciate-retaining TKA and condylar-stabilizing TKA compared with the normal knee. The patella offset in the normal knee decreased with increasing knee flexion angles, while the patella offset in the TKA knees did not change significantly through the full range of motion. The amount of lateral patella tilt in the normal knee was significantly larger than the TKA knees in the full range of motion.

CONCLUSION

Although the femoral components are designed to reproduce an anatomical patellar tracking, the physiological patellar kinematics were not observed. Relatively high patellofemoral pressure and kinematic change after TKA may be associated with postoperative complications such as the anterior knee pain.

Does computer-assisted surgery influence survivorship of cementless total knee arthroplasty in patients with primary osteoarthritis? A 10-year follow-up study

PURPOSE

Computer-assisted surgery (CAS) has been proposed to improve the performance of total knee arthroplasty (TKA) by reducing implant mal-position and mechanical axis mal-alignment. However, no clinical study has been performed to evaluate whether CAS improves survivorship of cementless TKA at long-term follow-up. This prospective and comparative study evaluated the outcome and survivorship of a cementless rotating mobile-bearing TKA performed with or without CAS at a minimum 10-year follow-up.

METHODS

A continuous series of 138 TKA (SCORE^®, Amplitude, Valence, France) comparing 87 CAS TKA versus 51 conventional mechanical technique (MECA) TKA was prospectively included in our total joint registry.

RESULTS

At 10.5 years after implantation, 95 TKA (59 CAS and 36 MECA TKA) were evaluated. No significant difference was detected in the clinical outcome and mechanical axis between the two groups. The overall 10-year survivorship using revision for any reason as end-point was 91 ± 5 % without significant difference detected between the two groups [86 ± 10 % in the MECA group and 94 ± 5 % in the CAS group (n.s.)]. Using aseptic loosening as end-point, the 10-year survivorship was 100 % in both groups. Using secondary patellar resurfacing as end-point, the 10-year survivorship was significantly higher in the CAS than in MECA group (100 and 85 ± 15 %, respectively; p = 0.0039).

CONCLUSION

With no implant aseptic loosening or mechanical failure at 10.5 years after implantation, the cementless rotating mobile-bearing SCORE^® TKA demonstrated favourable survivorship without influence of CAS. However, CAS might influence TKA survivorship by limiting secondary patellar resurfacing.

LEVEL OF EVIDENCE

Therapeutic, Level II.

Total knee arthroplasty using trochlear groove as guide for position of femoral component in severe knee osteoarthritis

BACKGROUND

Apart from transepicondylar axis, the native femoral sulcus was also reported to be used as a guide for the femoral component position in total knee arthroplasty (TKA). However, it was not shown in patients with severe knee osteoarthritis. This study was conducted to compare the position of trochlear groove in patients with and without osteoarthritis, and to assess whether trochlear groove could be used as a guide for position of femoral component in TKA for severe knee osteoarthritis.

METHODS

Total 50 severe knee osteoarthritis patients (Kellgren Lawrence grade 3 or 4) who underwent TKA were included. Meanwhile, 50 patients who underwent arthroscopic surgery without osteoarthritis were included as control. The distance from trochlear groove to the midpoint of a virtual anterior condyle osteotomy line (parallel to the posterior condyle line) (a-b) was recorded by radiological and surgical measurements. Midpoint of transepicondylar axis and trochlear groove were used as guide for placing prosthesis model in TKA, respectively. No-thumb test was performed to assess the patellar tracking. The position of femoral component was finally performed using trochlear groove as guide in TKA.

RESULTS

Value of "a-b" was significantly different between osteoarthritic and control knees (P = 0.008). During the placement of prosthesis model, similar patellar tracking was detected between using midpoint of transepicondylar axis and trochlear groove as guide (P > 0.05). After placing femoral component using trochlear groove as guide, most patients obtained good patellofemoral congruence with pneumatic tourniquet inflated (n = 43) or deflated (n = 5), and good patellofemoral congruence was also obtained by lateral patellar retinaculum release in two patients.

CONCLUSION

Despite the shifting of trochlear groove caused by severe knee osteoarthritis, trochlear groove can be used as a guide for position of femoral component, with equivalent patellar tracking compared with transepicondylar axis.

Intraoperative anthropomorphic study of anterior femoral condyles compared with sizing of femoral arthroplasty

PURPOSE

The present study was designed to compare the dimensions of the anterior femoral condyle with those of the anterior component flange using intraoperative morphological data.

METHODS

Overall, 1227 knees in 962 patients were included in this study. The height of the anterior lateral/medial condylar height (ALCH/AMCH) was measured and compared between men and women. These morphological data were compared with the dimensions of the chosen component for each patient. The lateral/medial anterior femoral offset was calculated, and the over-/understuffing rates were compared between men and women.

RESULTS

The median ALCH in men was 8.5 mm (6.5, 10.0 mm) versus 7.0 mm (6.0, 9.0 mm) in women. The median AMCH in men was 4.0 mm (2.5, 6.0 mm) versus 3.5 mm (2.5, 6.0 mm) in women. There was a significant difference between the genders with respect to ALCH (p < 0.05). When the dimensions of the component were compared with those of the native knee, the anterior lateral flange height was smaller than the native knees (1.3 mm in male, 0.7 mm in female), but the anterior medial flange height was larger than the corresponding condyle (1.8 mm in male, 1.8 mm in female). A significant difference was observed between the genders with respect to the ideal fit rate of ALCH (p < 0.01).

CONCLUSION

The results demonstrate that gender differences exist in the anterior lateral condyles of knees. The anterior flange of component is not designed to precisely reproduce normal trochlear anatomy.

LEVEL OF EVIDENCE

II.

Evolution of trochlear compartment geometry in total knee arthroplasty

BACKGROUND

The study aimed to compare trochlear profiles in recent total knee arthroplasty (TKA) models and to determine whether they feature improvements compared to their predecessors. The hypothesis was that recent TKA models have more anatomic trochlear compartments and would display no signs of trochlear dysplasia.

METHODS

The authors analyzed the geometry of the 6 following TKA models using engineering software: PFC and Attune (DePuy), NexGen and Persona (Zimmer), Noetos and KneeTec (Tornier). The mediolateral trochlear profiles were plotted at various flexion angles (0°, 15°, 30° and 45°) to deduce the sulcus angle.

RESULTS

Analysis of sulcus angles reveals general convergence of recent designs towards anatomic values. At 0° of flexion, sulcus angles of recent implant models were between 156.0-157.4°, while those of previous generation models between 154.5-165.5°. At 30° of flexion, sulcus angles of recent models also lie within 145.7-148.6°, but those of previous models are between 149.5-152.0°. All three manufacturers deepened their trochlear profile at 30° of flexion in recent models compared to earlier designs. Sulcus angles converge towards anatomic values but still exceed radiologic signs of dysplasia by 2-5°.

CONCLUSIONS

Recent TKA designs have more anatomic trochlear geometries than earlier TKA models by the same manufacturers, but trochlear compartments still exceed radiologic signs of trochlear dysplasia by 2° to 5°. The hypothesis that recent TKA models display no signs of trochlear dysplasia is therefore refuted. Surgeons should be aware of design limitations to optimize choice of implant and extensor mechanisms alignment.

LEVEL OF EVIDENCE

IV geometric implant analysis.

Anterior knee pain following primary total knee arthroplasty

Despite improvements in technique and technology for total knee arthroplasty (TKA), anterior knee pain impacts patient outcomes and satisfaction. Addressing the prosthetic and surgical technique related causes of pain after TKA, specifically as it relates to anterior knee pain, can aid surgeons in addressing these issues with their patients. Design features of the femoral and patellar components which have been reported as pain generators include: Improper femoral as well as patellar component sizing or designs that result in patellofemoral stuffing; a shortened trochlear groove distance from the flange to the intercondylar box; and then surgical technique related issues resulting in: Lateral patellar facet syndrome; overstuffed patella/flange combination; asymmetric patellar resurfacing, improper transverse plane component rotation resulting in patellar subluxation/tilt. Any design consideration that allows impingement of extensor mechanism anatomical elements has the possibility of impacting outcome by becoming a pain generator. As the number of TKA procedures continues to increase, it is increasingly critical to develop improved, evidence based prostheses that maximize function and patient satisfaction while minimizing pain and other complications.

Influence of the Rotational Alignment of the Femoral and Patellar Components on Patellar Tilt in Total Knee Arthroplasty

Purpose

The purpose of this study was to analyze the influence of rotational alignment of the femoral and patellar components on patellar tilt after total knee arthroplasty (TKA).

Materials and Methods

A total of 56 patients (76 knees) who underwent TKA using Advance Medial Pivot Knee system between May 2009 and April 2011 and were available for minimum 1-year follow-up were enrolled in this study. Whiteside's line and the transepicondylar line were used to determine the rotational alignment of the femoral component. Patella cut was aimed to be parallel to the anterior patellar cortex during surgery. Radiographic evaluation was performed using plain axial radiographs. The rotational alignment of the femoral component was measured as the angle between the anterior condylar axis and the surgical transepicondylar axis. The patellar resection angle was measured between the patellar resection axis and the anterior cortical line of the patella. Patellar tilt was evaluated to investigate the correlation with the rotation of the femoral component and patellar resection angle.

Results

The mean rotation of the femoral component was 0.42°±3.18° of internal rotation. The mean patellar resection angle was 1.82°±3.44°, indicating medial overresection. The mean patellar tilt was 6.12°±4.31° of lateral tilt. The rotational angle of the femoral component showed a negative correlation with patellar tilt in the linear regression analysis (p=0.749), but the patellar resection angle showed a positive correlation with patellar tilt (p<0.001).

Conclusions

Accurate patellar resection is recommended for proper patellar tracking in TKA.

The influence of component alignment on patellar kinematics in total knee arthroplasty

BACKGROUND AND PURPOSE

Postoperative anterior knee pain is one of the most frequent complications after total knee arthroplasty (TKA). Changes in patellar kinematics after TKA relative to the preoperative arthritic knee are not well understood. We compared the patellar kinematics preoperatively with the kinematics after ligament-balanced navigated TKA.

PATIENTS AND METHODS

We measured patellar tracking before and after ligament-balanced TKA in 40 consecutive patients using computer navigation. Furthermore, the influences of different femoral and tibial component alignment on patellar kinematics were analyzed using generalized linear models.

RESULTS

After TKA, the patellae shifted statistically significantly more laterally between 30° and 60°. The lateral tilt increased at 90° of flexion whereas the epicondylar distance decreased between 45° and 75° of flexion. Sagittal component alignment, but not rotational component alignment, had a significant influence on patellar kinematics.

INTERPRETATION

There are major differences in patellar kinematics between the preoperative arthritic knee and the knee after TKA. Combined sagittal component alignment in particular appears to have a major effect on patellar kinematics. Surgeons should be especially aware of altering preoperative sagittal alignment until the possible clinical relevance has been investigated.

Does patellofemoral geometry in TKA affect patellar position in mid-flexion?

PURPOSE

This study aimed to compare the position of the patella at 90° of flexion before and after implantation of two TKA models with identical tibiofemoral geometry but different trochlear and patellar designs. The hypothesis was that the design with the deeper 'anatomic' trochlea could produce more natural patellar positions.

METHODS

Intra-operative navigation data were collected from 22 consecutive cases that received two TKA designs (9 HLS Noetos(®) and 13 HLS KneeTec(®)). Both implants were cemented postero-stabilised TKAs with mobile tibial inserts and patellar resurfacing. Operations were guided by a non-image-based system that recorded relative femoral, tibial and patellar positions pre- and post-operatively.

RESULTS

The two groups exhibited little difference in femoral internal-external rotation and anterior-posterior translation during knee flexion. The two groups exhibited significant differences in patellar position at 90° of flexion. Post-operatively, the patella was similarly shifted medially relative to the femur (Noetos 6.9 mm, KneeTec 6.0 mm, n.s.). Patellar flexion was equivalent in native knees (Noetos 18.3°, KneeTec 20.5°, n.s.), but in implanted knees, it was considerably different (Noetos 6.3°, KneeTec 23.5°, p = 0.031).

CONCLUSIONS

The present study compared intra-operative navigation data from two patient series that received TKA implants with identical tibiofemoral articular geometry but different patellofemoral designs. The results confirm that tibiofemoral kinematics are unchanged, but that patellar positions at 90° of flexion offer greater mechanical advantage to the quadriceps using the KneeTec than using the Noetos. The findings raise awareness of influence of patellofemoral geometry on mid-flexion kinematics and help surgeons select the most suitable implant for patients with weak quadriceps muscles or with history of patellar instability.

LEVEL OF EVIDENCE

Comparative study, Level III.

Effect of medial-lateral malpositioning of the femoral component in total knee arthroplasty on anterior knee pain at greater than 8 years of follow-up

BACKGROUND

The trochlea is often medialized after total knee arthroplasty (TKA) resulting in abnormal patellar tracking, which may lead to anterior knee pain. However, due to the difference in shape of the natural trochlea and the patellar groove of the femoral component, a medialization of the femoral component of 5 mm results in an equal patellar position at 0-30° of flexion. We tested the hypothesis that more medialization of the trochlea results in a higher VAS pain score and lower Kujala anterior knee pain score at midterm follow-up.

METHODS

During surgery a special instrument was used to measure the mediolateral position of the natural trochlea and the prosthetic groove in 61 patients between 2004 and 2005. Patient reported outcome measures were used to investigate the clinical results (NRS-pain, NRS-satisfaction, KOOS-PS and Kujala knee score).

RESULTS

In total 40 patients were included. The mean follow-up was 8.8 years. A medialization of ≥5 mm resulted in a significantly lower NRS-pain (0.2 vs. 1.4; p=0.004) and higher NRS-satisfaction (9.6 vs. 8.2; p=0.045). Overall clinical results were good; KOOS-PS was 33.9 and Kujala knee score was 72.1.

CONCLUSIONS

The present study showed that a more medial position may result in a better postoperative outcome, which can probably be explained by the non-physiological lateral orientation of the trochlear groove in TKA designs.

LEVEL OF EVIDENCE

Level III.

Evidence of trochlear dysplasia in femoral component designs

PURPOSE

The study aimed to compare trochlear profiles of various total knee arthroplasty (TKA) models to anatomic profiles observed in healthy and pathologic knees and to evaluate trochlear designs against radiologic indicators for PF disorders and trochlear dysplasia.

METHODS

The trochlear profiles of 14 different TKA models were digitized using a coordinate measurement machine at various flexion angles (0°, 15°, 30° and 45°) to deduce the following variables: sulcus angle, trochlear groove orientation, height of lateral facet, and mediolateral groove position. The effect of externally rotating the femoral component on those variables was simulated.

RESULTS

The sulcus angle was greater than the indicators for trochlear dysplasia of 144° in 11 implants at 45° flexion, and in 13 implants at 30° flexion. The lateral facet height was less than average anatomic values of 5 mm in eight specimens through the entire range of early flexion (0°-30°). The trochlear groove was oriented laterally in 13 specimens (3.3°-11.7°) and was vertical in one specimen (0.3°). Applying an external rotation up to 6° resulted in noticeable lateral translation of the trochlear groove and facets, but negligible posterior translation.

CONCLUSIONS

The study presented a detailed description of previously overlooked TKA design parameters and revealed that some femoral components exhibit characteristics of trochlear dysplasia. The clinical relevance of this descriptive study is that surgeons should be aware of such design limitations to improve choice of implant for patients with history of PF disorders and to adapt surgical techniques as necessary to optimize PF tracking.

LEVEL OF EVIDENCE

Case-control study, Level III.

Evidence of trochlear dysplasia in patellofemoral arthroplasty designs

PURPOSE

The design of the trochlear compartment is crucial in patellofemoral arthroplasty (PFA), because 78% of patients with isolated patellofemoral arthritis present concomitant trochlear dysplasia with patellar maltracking and therefore remain predisposed to post-operative patellar subluxation and dislocation. The study investigated whether current PFA implants are designed with anatomic trochlear parameters such as the sulcus angle, lateral facet height and groove orientation.

METHODS

Five trochlear components of commercially available PFA implants were scanned, and the generated three-dimensional surfaces were measured using engineering design software. The mediolateral trochlear profiles were plotted at various flexion angles (0°, 15°, 30° and 45°) to deduce the following variables: sulcus angle, height of lateral facet and trochlear groove orientation.

RESULTS

Four specimens had sulcus angle>144° in the 45° of flexion, and all five specimens had sulcus angle>143° in 30° of flexion. Three specimens had a facet<5 mm high through the entire range of early flexion (0°-30°), and two specimens had a facet<5 mm high beyond early flexion (30°-45°). The trochlear groove was oriented laterally in all specimens (range 1.6°-13.5°).

CONCLUSION

Current PFA trochlear components are not always designed with anatomic parameters, and some models exhibit characteristics of trochlear dysplasia. Surgeons are therefore advised to implant components with a deep sulcus, particularly in patients with history of patellofemoral disorders, and to adapt the surgical technique and extensor mechanism if the component implanted has a shallow sulcus, to ensure normal patellar tracking.

LEVEL OF EVIDENCE

III.

Gender analysis of the anterior femoral condyle geometry of the knee

BACKGROUND

No study has used 3-D anatomic knee models to investigate the gender differences in anterior femoral condyles. Therefore, this study aims to determine the morphologic differences between genders in anterior femoral condyles of the knees using 3-D anatomic knee models.

METHODS

Ninety-six male and sixty-five female 3D anatomic knee models were used to measure lateral and medial anterior condyle heights, anterior trochlear groove heights, and anterior condyle width, which were normalized by the anterior-posterior and medial-lateral dimensions of the knee, respectively. The shape of anterior condyle groove was also analyzed.

RESULTS

The mean lateral anterior condyle height, medial anterior condyle height and anterior condyle width of females were 6.6±1.8 mm, 2.0±2.3 mm, and 44.7±4.2 mm, respectively. These data were significantly smaller (p<0.05) than those of males (7.7±1.8 mm, 2.9±2.0 mm and 50.0±3.4 mm). However, after normalizing by the femur size, the aspect ratios had no gender differences. Both the ranges of lateral and medial condyle of females were significantly smaller than those of males, and the geometry curve of anterior condyle was different between genders.

CONCLUSION

Although the gender differences in anterior femoral condyle sizes no longer existed after normalization with the femur size, the shape and the peak position of anterior condyle groove still have gender differences. The data may have important implications on the current debate of gender-specific TKAs.

CLINICAL RELEVANCE

This study provides a better understanding of gender differences in anterior femoral condyle geometry.

Coronal alignment of patellofemoral arthroplasty

BACKGROUND

Patellofemoral arthroplasty (PFA) can yield successful results in appropriately selected patients. The varus-valgus position or coronal alignment of the trochlear implant is determined by how its transitional edges articulate with the condylar cartilage. Whilst variation in condylar anatomy will not influence the axis of the lower limb in PFA, it can impact on the Q-angle of the PF joint. The aim of this study was to analyze how the coronal alignment can be influenced by the choice of anatomical landmarks.

MATERIALS AND METHODS

Retrospective analysis of 57 PFAs with measurements of alignment from full leg radiographs.

RESULTS

Coronal alignment following anterior condylar anatomy leads to a mean (SD) proximal valgus alignment of 100° (9°). Aligning the component with Whiteside's line gives a better alignment with less variance 89° (3°).

DISCUSSION

A trochlear component with a higher Q-angle compensates for patellar maltracking if the condylar anatomy would tend to put the implant in a more proximal varus or neutral position. If the trochlear component is proximally aligned in valgus this may have the opposite effect. Aligning the trochlear component with the AP-axis in the coronal plane avoids maltracking and optimally utilizes the design features of the implant.

LEVEL OF EVIDENCE

Level III.

Patellofemoral contact patterns before and after total knee arthroplasty: an in vitro measurement

Background

Patellofemoral complications are one of the main problems after Total Knee Arthroplasty (TKA). Retropatellar pressure distribution after TKA can contribute to these symptoms. Therefore we evaluated retropatellar pressure distribution subdivided on the ridge, medial and lateral surface on non-resurfaced patella before and after TKA. Additionally, we analyzed axial femorotibial rotation and quadriceps load before and after TKA.

Methods

Seven fresh frozen cadaver knees were tested in a force controlled knee rig before and after TKA (Aesculap, Tuttlingen, Germany, Columbus CR) while isokinetic flexing the knee from 20° to 120° under weight bearing. Ridge, medial and lateral retropatellar surface were defined and pressure distribution was dynamically measured while quadriceps muscles and hamstring forces were applied. Aside axial femorotibial rotation and quadriceps load was recorded.

Results

There was a significant change of patella pressure distribution before and after TKA (p = 0.004). In physiological knees pressure distribution on medial and lateral retropatellar surface was similar. After TKA the ridge of the patella was especially in higher flexion grades strongly loaded (6.09 +/−1.31 MPa) compared to the natural knee (2.92 +/−1.15 MPa, p < 0.0001). Axial femorotibial rotation showed typical internal rotation with increasing flexion both before and after TKA, but postoperatively it was significantly lower. The average amount of axial rotation was 3.5° before and after TKA 1.3° (p = 0.001). Mean quadriceps loading after implantation of knee prosthesis did not change significantly (575 N ±60 N in natural knee and after TKA 607 N ±96 N; p = 0.28).

Conclusions

The increased retropatellar pressure especially on the ridge may be one important reason for anterior knee pain after TKA. The trochlea of the femoral component might highly influence the pressure distribution of the non-resurfaced retropatellar surface. Additionally, lower axial femorotibial rotation after TKA might lead to patella maltracking. Changing the design of the prosthesis or a special way of patella shaping might increase the conformity of the patella to trochlea to maintain natural contact patterns.

Contemporary femoral designs in total knee arthroplasty: effects on the patello-femoral congruence

PURPOSE

The objective of this study was to evaluate the radiological and clinical correlations between implant design and patellar positioning in patients who underwent TKA utilizing femoral implants with modern designs.

METHODS

Thirty consecutive PFC PS Sigma TKAs, characterized by a new prolonged anterior flange and a "smoother" trochlea, were prospectively reviewed. All patellae were replaced. All patients were evaluated pre-operatively and prospectively at two years follow-up both clinically according to the Knee Society score as well as radiographically. This included computed tomography (CT); patellar tilt, patellar conformity angle, patellar lateralization, and femoral component external-rotation in relation to the clinical trans-epicondylar axis.

RESULTS

Average patellar tilt at follow-up was 3° (±7.5°) with respect to a pre-operative 18.5° (±8.5°). Average patellar congruence angle at follow-up was -3° (range, -11° to +9°) with respect to a pre-operative 10.3° (range, + 1.5° to 25.5°). Average lateralization index at follow-up was 2.7 mm (range, -3.4 mm to +7.1 mm) with respect to a pre-operative 12.2 mm (± 4.8 mm). Femoral component positioning related to the trans-epicondylar axis showed an external rotation of 2.80° (± 2.10°) at follow-up with respect to 5.7° (± 1.80°). Clinically, two (6.6%) patients reported patello-femoral complications related to imperfections in the surgical technique more than the implant's design.

CONCLUSIONS

This study highlighted that modern femoral designs in TKA allow for a correct reproducibility of a normal patello-femoral conformity. Strict surgical principles are paramount to avoid patello-femoral complications even when modern implants are used.