1
|
Pagano S, Plate JF, Kappenschneider T, Reinhard J, Scharf M, Maderbacher G. Polyethylene liner dissociation in total hip arthroplasty: a retrospective case-control study on a single implant design. J Orthop Traumatol 2024; 25:38. [PMID: 39143399 PMCID: PMC11324622 DOI: 10.1186/s10195-024-00785-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 05/26/2024] [Accepted: 08/01/2024] [Indexed: 08/16/2024] Open
Abstract
BACKGROUND Modular acetabular components for total hip arthroplasty (THA) provide intraoperative flexibility; however, polyethylene liner dissociation may occur. This study aimed to examine the incidence and causes of liner dissociation associated with a specific acetabular component design at a single centre. MATERIALS AND METHODS A retrospective analysis of 7027 patients who underwent primary THA was performed to identify isolated liner dislocations. Patient demographics, clinical presentations, surgical and implant details, and both radiographic and computed tomography (CT) findings were analysed. Patients with liner dislocation were matched to a control group via 2:1 propensity score matching, and a logistic regression analysis was employed to identify associated risk factors. RESULTS A total of 32 patients (0.45%) experienced liner dislocation at a mean 71.47 ± 60.10 months post surgery. Significant factors contributing to dislocations included the use of a conventional compared with a highly crosslinked polyethylene component (p = 0.049) and screw fixation (p = 0.028). Radiographic and CT analysis highlighted the importance of proper component orientation, revealing that patients experiencing dislocations demonstrated significantly lower acetabular cup anteversion angles (p = 0.001) compared with the control group. Impingement and malposition, identified in 41% and 47% of the cases, respectively, further underscored the multifactorial nature of dislocation risks. CONCLUSIONS While the overall rate of polyethylene liner dislocation was low, the findings of this study highlight the importance of appropriate cup placement to decrease the risk of dissociation. It further substantiates the influence of impingement and malposition in liner displacement, with increased mechanical stress exerted on the locking mechanism under adverse conditions and the potential risk increase due to screw placement.
Collapse
Affiliation(s)
- S Pagano
- Department of Orthopaedic Surgery, University of Regensburg, Asklepios Klinikum, Kaiser-Karl-V.-Allee 3, 93077, Bad Abbach, Germany.
| | - J F Plate
- Department of Orthopaedic Surgery, University of Pittsburgh Medical Center, Pittsburgh, PA, USA
| | - T Kappenschneider
- Department of Orthopaedic Surgery, University of Regensburg, Asklepios Klinikum, Kaiser-Karl-V.-Allee 3, 93077, Bad Abbach, Germany
| | - J Reinhard
- Department of Orthopaedic Surgery, University of Regensburg, Asklepios Klinikum, Kaiser-Karl-V.-Allee 3, 93077, Bad Abbach, Germany
| | - M Scharf
- Department of Orthopaedic Surgery, University of Regensburg, Asklepios Klinikum, Kaiser-Karl-V.-Allee 3, 93077, Bad Abbach, Germany
| | - G Maderbacher
- Department of Orthopaedic Surgery, University of Regensburg, Asklepios Klinikum, Kaiser-Karl-V.-Allee 3, 93077, Bad Abbach, Germany
| |
Collapse
|
2
|
Jalali O, Fiske J, DeJardin MG, Scudday TS, Barnett SL, Gorab RS. Wear of Third-Generation Cross-Linked Polyethylene in Primary Total Hip Arthroplasty: A 10-Year Analysis. J Arthroplasty 2024; 39:1335-1340. [PMID: 37977306 DOI: 10.1016/j.arth.2023.11.016] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 05/07/2023] [Revised: 11/08/2023] [Accepted: 11/10/2023] [Indexed: 11/19/2023] Open
Abstract
BACKGROUND Sequential modifications to the manufacturing process of highly cross-linked polyethylene (HXLPE) have improved the wear resistance and implant survival of these liners in total hip arthroplasty (THA). However, no study has examined the long-term (mean 10 year) wear rates and clinical outcomes of third-generation HXLPE in THA. The aim of our study was to report the longest-to-date analysis of wear rates and clinical outcomes of a third-generation HXLPE liner. METHODS A series of 133 THAs using a specific HXLPE acetabular liner were retrospectively evaluated. Linear and volumetric wear rates were determined using a validated radiographic technique and clinical outcomes were analyzed. Multivariate analyses were performed to determine risk factors for accelerated wear. RESULTS At a mean follow-up of 10.4 years (range, 8 to 13.4), the mean linear wear rate was 0.0172 mm/year and the mean volumetric wear rate was 16.99 mm3/year. There were no instances of osteolysis or mechanical failures at any time point and there was a 100% acetabular component survival rate. Younger age and use of offset liners were independent risk factors for increased wear (P < .01 for both). CONCLUSIONS Our series of a third-generation HXLPE demonstrated very low wear rates and excellent implant survival at a mean of 10.4 years following primary THA. Future comparative studies at the 15- and 20-year follow-up timepoints are necessary to determine if such findings translate to true improvements in the tribological properties and longevity of these liners when compared to previous generations of HXLPE liners.
Collapse
Affiliation(s)
- Omid Jalali
- Department of Orthopaedic Surgery, University of California, San Diego, San Diego, California
| | - Joseph Fiske
- College of Osteopathic Medicine, Touro University California, Vallejo, California
| | | | - Travis S Scudday
- Department of Orthopaedic Surgery, Hoag Orthopedic Institute, Irvine, California
| | - Steven L Barnett
- Department of Orthopaedic Surgery, Hoag Orthopedic Institute, Irvine, California
| | - Robert S Gorab
- Department of Orthopaedic Surgery, Hoag Orthopedic Institute, Irvine, California
| |
Collapse
|
3
|
Deans CF, Buckner BC, Garvin KL. Wear, Osteolysis, and Aseptic Loosening Following Total Hip Arthroplasty in Young Patients with Highly Cross-Linked Polyethylene: A Review of Studies with a Follow-Up of over 15 Years. J Clin Med 2023; 12:6615. [PMID: 37892754 PMCID: PMC10607435 DOI: 10.3390/jcm12206615] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/01/2023] [Revised: 09/26/2023] [Accepted: 10/10/2023] [Indexed: 10/29/2023] Open
Abstract
Total hip arthroplasty (THA) has in recent years trended toward a younger, more physically demanding patient population. Mid- to long-term studies of all ages of THA patients using highly cross-linked polyethylene (HXLPE) have been favorable, but concerns about its long-term failure and wear-related complications remain for young THA patients. In this narrative review, a search of the PubMed/MEDLINE and Cochrane databases was performed, and we identified six studies with a minimum 15-year follow-up of HXLPE with various femoral head materials. Wear-related revisions were exceedingly low for patients under the age of 55, with variable reports of non-clinically significant osteolysis. Higher activity levels, a larger femoral head size, and femoral head material were not associated with greater long-term wear rates. Young THA with metal or ceramic on HXLPE is exceedingly durable with favorable outcomes at follow-ups of over 15 years.
Collapse
Affiliation(s)
| | | | - Kevin L. Garvin
- Department of Orthopaedic Surgery & Rehabilitation, University of Nebraska Medical Center, 985640 Nebraska Medical Center, Omaha, NE 68198, USA
| |
Collapse
|
4
|
Bingham JS, Hinckley NB, Deckey DG, Hines J, Spangehl MJ. Primary Tritanium acetabular components have increased rates of radiolucency associated with inferior clinical outcomes at short-term follow-up. Hip Int 2022; 32:724-729. [PMID: 33566724 DOI: 10.1177/1120700020988723] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/04/2023]
Abstract
INTRODUCTION Cementless fixation is the standard for acetabular fixation in primary total hip arthroplasty (THA). There are various surface finishes thought to improve osteointegration, although literature regarding the long-term survival of some of these surfaces is limited. Regardless of design, primary stability is essential to allow for osteointegration. Previous studies have suggested an increased rate of radiolucency and compromised short-term functional outcomes using the Tritanium primary acetabular component (Stryker, Mahwah, NJ). The purpose of this study was to compare the primary Tritanium acetabular component to another contemporary acetabular component as a control group with an established clinical record. METHODS 444 consecutive, primary THAs performed by a single surgeon from 2008 to 2012 were reviewed. Patients were included if they had a minimum 1-year follow-up. Implant survivorship and modified Harris Hip Scores (mHHS) were recorded for all patients at final follow-up. Radiographs were evaluated by 2 surgeons at 6 weeks, 1 year, and the most recent follow-up for evidence of radiolucency and migration. Components were considered to have evidence of radiographic lucency if they had radiolucency in 2 or more DeLee zones. RESULTS 198 patients met criteria for inclusion (96 Pinnacle, 102 Tritanium). Average follow-up was 28 (12-72) months. At final follow-up 6.2% of the Pinnacle cups and 29.4% of the Tritanium cups had radiographic evidence of loosening (p < 0.01). The average mHHS for the Tritanium group was 83.1, and 88.4 for the Pinnacle group (p < 0.01). Radiographic evidence of loosening also correlated with a lower mHHS: 75.5 versus 86.4 (p < 0.01). In patients that received Tritanium cups without screw fixation 44.6% showed radiographic evidence of loosening versus 8% that received screw fixation (p < 0.01). In total, 6 patients in the Tritanium group required revision for aseptic loosening of the acetabular component. CONCLUSIONS The 30% rate of radiographic loosening in the Tritanium group was significantly higher than the Pinnacle group and correlated with an inferior clinical outcome. Interestingly the use of screw augmentation was protective against radiographic evidence of loosening. This suggests that the Tritanium component may be prone to fibrous in-growth because of inadequate primary stability.
Collapse
Affiliation(s)
- Joshua S Bingham
- Department of Orthopaedics, Mayo Clinic Arizona, Phoenix, AZ, USA
| | | | - David G Deckey
- Department of Orthopaedics, Mayo Clinic Arizona, Phoenix, AZ, USA
| | - Jeremy Hines
- Department of Orthopaedics, Mayo Clinic Rochester, Rochester, MN, USA
| | - Mark J Spangehl
- Department of Orthopaedics, Mayo Clinic Arizona, Phoenix, AZ, USA
| |
Collapse
|
5
|
Beckmann NA, Schonhoff M, Bastian JD, Renkawitz T, Jaeger S. Dissociation of liner from cup in THA: does liner damage affect the risk of dissociation? Arch Orthop Trauma Surg 2022; 143:2747-2754. [PMID: 35788763 PMCID: PMC10110686 DOI: 10.1007/s00402-022-04529-8] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 04/01/2022] [Accepted: 06/16/2022] [Indexed: 11/02/2022]
Abstract
INTRODUCTION A rare catastrophic failure of modular component Total Hip Arthroplasty is dissociation between liner and cup, which has been associated with component malposition and/or impingement and seems to be more frequently associated with the Pinnacle system. The goal of this study was to evaluate the resistance of a polyethylene liner to lever-out-forces of the Pinnacle locking mechanism and the locking mechanisms of two other current cup/liner systems using a standardized testing method (ASTM). MATERIALS AND METHODS Five of each of the following cups were evaluated with their corresponding polyethylene liners: Pinnacle Multihole cup with and without intact anti-rotation tabs (ART's); Allofit-S-Alloclassic and Plasmafit Plus7 cups. The ASTM test set-up was used to evaluate the lever-out force resulting in liner dissociation for each construct. RESULTS The Pinnacle construct with intact ARTs required the greatest force (F) to achieve dissociation (263.2 ± 79.2 N) followed by the Plasmafit Plus7 (185.8 ± 36.9 N) and the Allofit-S (101.4 ± 35.3 N) constructs, respectively. However, after removal of the ARTs, the Pinnacle system required the least force to achieve dissociation (75.1 ± 22.2 N) (p < 0.001). CONCLUSIONS The intact Pinnacle system appeared the most stable in lever-out tests when compared to the other systems. However, after removal of the ARTs, the Pinnacle system required the least force for dissociation, consistent with locking mechanism failure, and suggesting that the ARTs are a critical component of the locking mechanism. Our findings are consistent with the clinical experience of dissociated Pinnacle constructs displaying damaged or missing ARTs, and that damage to these may increase risk of liner dissociation.
Collapse
Affiliation(s)
- Nicholas Andreas Beckmann
- Center for Orthopedics, Trauma Surgery and Spinal Cord Injury, Heidelberg University Hospital, Schlierbacher Landstrasse 200a, 69118, Heidelberg, Germany.
| | - Mareike Schonhoff
- Laboratory of Biomechanics and Implant Research, Center for Orthopedics, Trauma Surgery and Spinal Cord Injury, Heidelberg University Hospital, Heidelberg, Germany
| | - Johannes Dominik Bastian
- Department of Orthopaedic Surgery and Traumatology, Inselspital, Bern University Hospital, University of Bern, Bern, Switzerland
| | - Tobias Renkawitz
- Center for Orthopedics, Trauma Surgery and Spinal Cord Injury, Heidelberg University Hospital, Schlierbacher Landstrasse 200a, 69118, Heidelberg, Germany
| | - Sebastian Jaeger
- Laboratory of Biomechanics and Implant Research, Center for Orthopedics, Trauma Surgery and Spinal Cord Injury, Heidelberg University Hospital, Heidelberg, Germany
| |
Collapse
|
6
|
Different wear in two highly cross-linked polyethylene liners in THA: wear analysis with EBRA. Arch Orthop Trauma Surg 2021; 141:1591-1599. [PMID: 33661385 PMCID: PMC8354953 DOI: 10.1007/s00402-021-03832-0] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/25/2020] [Accepted: 02/08/2021] [Indexed: 11/18/2022]
Abstract
INTRODUCTION The purpose of this study was (1) to compare early wear rates in bedding-in periods of two highly cross-linked polyethylene liners frequently used in THA and (2) to evaluate risk factors indicating a possible higher wear rate. MATERIALS AND METHODS 1120 patients who received a Crossfire or a Marathon highly cross-linked (HXLPE) ultra-high-molecular-weight polyethylene liner in primary THA at our Department between 2004 and 2018 were retrospectively reviewed. Patients with (1) only alumina heads on HXLPE acetabular bearings, (2) a minimum of four radiographs per patient for EBRA analysis, (3) no osteolysis around the acetabular cup and (4) no dislocations that occurred during the study period were included. RESULTS A total of 328 patients (female: 183; male: 145; Marathon: 179; Crossfire: 149) fulfilled the inclusion criteria. Mean follow-up was 24 (range 7-51) months. With 0.22 (SD 0.27) mm mean total wear for the Marathon was three times greater than for the Crossfire, namely 0.07 (SD 0.14) mm. Mean cup migration during the investigated follow-up period was 0.7 (SD 0.8) mm for the Pinnacle and 0.5 mm (SD 0.7) for the Trident PSL cups. CONCLUSION Initial early wear of highly cross-linked polyethylene in combination with alumina heads differs strongly between products. Long-term survivorship of these liners should be observed to determine whether early wear has an impact on aseptic loosening. LEVEL OF EVIDENCE Level III (retrospective comparative study with prospective cohort).
Collapse
|
7
|
Gwynne-Jones DP, Memon A. Acetabular Liner Dissociation: A Comparative Study of Two Contemporary Uncemented Acetabular Components. Arthroplast Today 2020; 6:354-359. [PMID: 32566716 PMCID: PMC7298534 DOI: 10.1016/j.artd.2020.04.016] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 02/04/2020] [Revised: 04/13/2020] [Accepted: 04/18/2020] [Indexed: 12/23/2022] Open
Abstract
BACKGROUND There are a number of reports of polyethylene liner dissociation of third-generation modular acetabular components. This study compares our experience with 2 contemporary systems to determine whether this is an implant- or class-specific problem. METHODS This is a single-center retrospective study of 961 primary total hip arthroplasties using 2 third-generation modular cementless acetabular shells: Pinnacle (535) and R3 (426) with a polyethylene liner. Details of all revisions were obtained from local databases and the New Zealand Joint Registry. Kaplan-Meier survival curves were calculated for all-cause revision, acetabular reoperation (including liner exchange), and liner dissociation. RESULTS There were 17 revisions in group 1 (Pinnacle; DePuy Synthes): 17 for recurrent dislocation, 6 for liner dissociations (1.12%), 3 for femoral loosening, and one for deep infection. In group 2 (R3; Smith and Nephew), there were 4 revision procedures: one for infection, 2 for dislocation, and one femoral revision for periprosthetic fracture. There were significantly higher proportions revised in group 1 for all-cause revision, acetabular reoperation, and dissociation (P = .024 to 0.038). The 7-year survival for all-cause revision was 96.1% for Pinnacle and 99.0% for R3 (P = .022), and that in the acetabular reoperation group was 96.9% for Pinnacle and 99.3% for R3 (P = .035). CONCLUSIONS There was a higher revision rate for the Pinnacle acetabular component than for the R3 at 7 years. This was mainly due to polyethylene liner dissociation that can occur early or late. It appears to be a problem specific to the Pinnacle cup design rather than a feature of similar third-generation acetabular components.
Collapse
Affiliation(s)
- David P. Gwynne-Jones
- Centre for Musculoskeletal Outcomes Research, Department of Surgical Sciences, Dunedin School of Medicine, University of Otago, Dunedin, New Zealand
- Department of Orthopaedic Surgery, Dunedin Hospital, Southern District Health Board, Dunedin, New Zealand
| | - Adeel Memon
- Department of Orthopaedic Surgery, Dunedin Hospital, Southern District Health Board, Dunedin, New Zealand
| |
Collapse
|
8
|
Baba S, Motomura G, Ikemura S, Yamaguchi R, Hamai S, Fujii M, Kawano K, Nakashima Y. Risk factors for radiological changes after bipolar hemiarthroplasty for osteonecrosis of the femoral head. Mod Rheumatol 2020; 31:725-732. [PMID: 32475189 DOI: 10.1080/14397595.2020.1775959] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/24/2022]
Abstract
OBJECTIVES This study aimed to report the mid-term radiological outcomes of patients with bipolar hemiarthroplasty (BHA) for stage 3 osteonecrosis of the femoral head (ONFH), and to identify the risk factors for postoperative radiological changes. METHODS We retrospectively investigated 62 patients (38 men and 24 women; mean age, 50.1 years) aged <70 years who underwent primary BHA for Association Research Circulation Osseous stage 3 ONFH between 1998 and 2010. The mean follow-up period after BHA was 12.8 years. The following changes were assessed on follow-up radiographs: outer head migration, polyethylene wear, and femoral osteolysis. The association between demographic data and the development of postoperative radiological changes was evaluated. RESULTS Radiological changes were found in 20 hips (32.3%) at a mean of 8.1 years after BHA; of these, three hips (4.8%) underwent total hip arthroplasty conversion at a mean of 10.9 years after BHA. Both univariate and multivariate analysis revealed that younger age and female sex were independent risk factors for the development of postoperative radiological changes. CONCLUSION The current results suggest that the indication of BHA should be carefully determined in young or female patients with ONFH, even when the disease is in the early stage.
Collapse
Affiliation(s)
- Shoji Baba
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Goro Motomura
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Satoshi Ikemura
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Ryosuke Yamaguchi
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Satoshi Hamai
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Masanori Fujii
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Koichiro Kawano
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| | - Yasuharu Nakashima
- Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Kyushu University, Fukuoka, Japan
| |
Collapse
|
9
|
Rames RD, Stambough JB, Pashos GE, Maloney WJ, Martell JM, Clohisy JC. Fifteen-Year Results of Total Hip Arthroplasty With Cobalt-Chromium Femoral Heads on Highly Cross-Linked Polyethylene in Patients 50 Years and Less. J Arthroplasty 2019; 34:1143-1149. [PMID: 30808529 DOI: 10.1016/j.arth.2019.01.071] [Citation(s) in RCA: 33] [Impact Index Per Article: 6.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/08/2018] [Revised: 01/25/2019] [Accepted: 01/28/2019] [Indexed: 02/01/2023] Open
Abstract
BACKGROUND Highly cross-linked polyethylene (HXLPE) is the most commonly used bearing surface in total hip arthroplasty (THA) because of its superior wear properties, but long-term results in young patients are limited. Mid-term survivorship has been promising; however, polyethylene wear rates and need for revision surgeries remain a concern in this population. The purpose of our study is to investigate polyethylene wear rates, implant survivorship, wear-related revisions, and patient-reported outcomes in a young patient cohort at 15-year follow-up. METHODS We performed a retrospective study of a prospective longitudinal cohort of 82 consecutive patients (89 hips) who underwent primary THA with an HXLPE acetabular liner and a cobalt-chromium femoral head. The mean age at the time of surgery for the cohort was 38.8 years (range 12-50). All patients received HXLPE liners with a cementless acetabular component coupled with a cobalt-chrome femoral head through a posterior approach with a cementless femoral component. All components were from a single manufacturer. We recorded University of California, Los Angeles Activity, and modified Harris Hip Scores. Wear calculations were made using the Martell Hip Analysis Suite (Version 8.0.4.3). RESULTS At average 15 years (range 13.1-18.5), there was a revision-free survivorship of 97.8% in our HXLPE group with no wear-related revisions. We observed a linear wear rate of 0.0185 mm/y (standard deviation 0.05) after accounting for a 1-year bedding-in period. The volumetric wear rate was found to be 12.80 mm3/y (standard deviation 22.69). These numbers are registered as clinically undetectable and are comparable to steady state wear rates in the same cohort of patients at earlier time points. We found no radiographic changes concerning osteolysis. We observed excellent patient-reported outcomes at this time point with improvements in modified Harris Hip Scores (35.3 [22.5], P < .0001) and University of California, Los Angeles Activity Scores (median 6.0, P < .0001). CONCLUSION At 15-year follow-up, we demonstrated that HXLPE bearings in this young cohort had excellent wear properties, maintained superior clinical improvements, and underwent no wear-related revision operations. The HXLPE and cobalt-chrome bearing couple continues to be extremely effective 15 years after primary THA in patients less than 50 years. LEVEL OF EVIDENCE IV.
Collapse
Affiliation(s)
- Richard D Rames
- Department of Orthopaedic Surgery, Washington University School of Medicine, St. Louis, MO
| | - Jeffrey B Stambough
- Department of Orthopaedic Surgery, University of Arkansas for Medical Sciences, Little Rock, AR
| | - Gail E Pashos
- Department of Orthopaedic Surgery, Washington University School of Medicine, St. Louis, MO
| | - William J Maloney
- Department of Orthopedic Surgery, Stanford Medicine Outpatient Center, Redwood City, CA
| | - John M Martell
- Department of Orthopaedic Surgery and Rehabilitation Medicine, Orthopaedic Biomedical Institute, University of Chicago Medicine & Biological Sciences, Chicago, IL
| | - John C Clohisy
- Department of Orthopaedic Surgery, Washington University School of Medicine, St. Louis, MO
| |
Collapse
|
10
|
O'Rourke D, Bottema M, Taylor M. Sampling strategies for approximating patient variability in population-based finite element studies of total hip replacement. INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN BIOMEDICAL ENGINEERING 2019; 35:e3168. [PMID: 30394696 DOI: 10.1002/cnm.3168] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/06/2018] [Revised: 10/26/2018] [Accepted: 10/27/2018] [Indexed: 06/08/2023]
Abstract
Total hip replacements must be robust to patient variability for long-term success in the population. The challenge during the design process is evaluating an implant in a diverse population but the computational cost of simulating a population of subject-specific finite element (FE) models is not practical. We examined five strategies to generate representative subsets of subjects from a cohort of 103 implanted hip joint FE models to approximate the variability in output metrics. Comparing with the median and distribution of the 95th percentile composite peak micromotion (CPM) and polar gap in the full cohort (CPM median: 136 μm, interquartile range [IQR]: 74-230 μm) (Polar Gap median: 467 μm, IQR: 434-548 μm), the Anatomic Sampling strategy (12 subjects) achieved the best balance of computational cost and approximation of the output metrics (CPM median: 169 μm, IQR: 78-236 μm) (Polar Gap median: 469 μm, IQR: 448-537 μm). Convex hull sampling (41 subjects) more closely captured the output metrics (CPM median: 99 μm, IQR: 70-191 μm) (Polar Gap median: 456 μm, IQR: 418-533 μm) but required over three times the number of subjects. Volume reduction of the convex hull captured the extremes of variability with subsets of 5 to 20 subjects, while the largest minimum-distance strategy captured the variability toward the middle of the cohort. These strategies can estimate the level of variability in FE model output metrics with a low computational cost when evaluating implants during the design process.
Collapse
Affiliation(s)
- Dermot O'Rourke
- Medical Device Research Institute, Flinders University, 1284 South Road, SA, 5042, Australia
| | - Murk Bottema
- Medical Device Research Institute, Flinders University, 1284 South Road, SA, 5042, Australia
| | - Mark Taylor
- Medical Device Research Institute, Flinders University, 1284 South Road, SA, 5042, Australia
| |
Collapse
|
11
|
Singh G, Klassen R, Howard J, Naudie D, Teeter M, Lanting B. Manufacturing, oxidation, mechanical properties and clinical performance of highly cross-linked polyethylene in total hip arthroplasty. Hip Int 2018; 28:573-583. [PMID: 29998768 DOI: 10.1177/1120700018780677] [Citation(s) in RCA: 16] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/04/2023]
Abstract
Ultra-high molecular weight polyethylene (UHMWPE) continues to be the gold standard bearing surface in total hip arthroplasty (THA) for nearly 5 decades. Highly cross-linked UHMWPE (HXLPE) was adapted for routine use in the early 2000s to reduce the revision rates related to wear, osteolysis, and aseptic loosening resulting from conventional UHMWPE wear. Since its inception, consistent evidence showing reduced wear rates and osteolysis supports the use of HXLPE in THA. High quality studies demonstrating the advantage in long term survivorship of HXLPE over conventional UHMWPE are emerging. Though retrieval studies have demonstrated evidence of in vivo oxidation and fatigue related damage at the rim of the first generation HXLPE liners, clinical significance of this remains to be seen. Second-generation sequentially annealed and vitamin E containing HXLPE liners demonstrate improved mechanical properties, resistance to oxidation, and equivalent wear rates in comparison to their first-generation counterparts, but long term success remains to be seen.
Collapse
Affiliation(s)
- Gurpreet Singh
- 1 Joint Replacement Institute, London Health Science Center (LHSC), University Hospital, Schulich School of Medicine, Western University, London, Ontario, Canada
| | - Robert Klassen
- 2 Department of Mechanical and Materials Engineering, Western University, London, Ontario, Canada
| | - James Howard
- 1 Joint Replacement Institute, London Health Science Center (LHSC), University Hospital, Schulich School of Medicine, Western University, London, Ontario, Canada
| | - Douglas Naudie
- 1 Joint Replacement Institute, London Health Science Center (LHSC), University Hospital, Schulich School of Medicine, Western University, London, Ontario, Canada
| | - Matthew Teeter
- 3 Joint Replacement Institute, LHSC, University Hospital, Department of Medical Biophysics, Western University, Surgical Innovation Program, Lawson Health Research Institute, London, Ontario, Canada
| | - Brent Lanting
- 1 Joint Replacement Institute, London Health Science Center (LHSC), University Hospital, Schulich School of Medicine, Western University, London, Ontario, Canada
| |
Collapse
|
12
|
Christensen DD, Nelms NJ. Competitive Running After Total Hip Arthroplasty: The World's Fastest Total Hip: A Case Report. JBJS Case Connect 2018; 8:e81. [PMID: 30303849 DOI: 10.2106/jbjs.cc.18.00030] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/14/2022]
Abstract
CASE We report the case of a young man who underwent total hip arthroplasty (THA) for osteonecrosis at the age of 20 years, and subsequently competed in collegiate long-distance running. The pinnacle of his career was setting the school record time of 3:47.64 (min:sec) in the 1,500-m "metric mile" run (equivalent to 4:05.09 for the "English" mile). This is the fastest known time for any patient who has undergone THA. Excellent clinical and radiographic outcomes had been maintained at 6 years postoperatively. CONCLUSION Patients who undergo arthroplasty procedures may be capable of remarkable physical accomplishments, but pursuing such feats is not advised.
Collapse
Affiliation(s)
- David D Christensen
- Orthopaedic Surgery and Rehabilitation Department, University of Vermont, Burlington, Vermont
| | | |
Collapse
|
13
|
O'Rourke D, Al-Dirini RM, Taylor M. Primary stability of a cementless acetabular cup in a cohort of patient-specific finite element models. J Orthop Res 2018; 36:1012-1023. [PMID: 28833500 DOI: 10.1002/jor.23709] [Citation(s) in RCA: 18] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 04/22/2017] [Accepted: 08/01/2017] [Indexed: 02/04/2023]
Abstract
The primary stability achieved during total hip arthroplasty determines the long-term success of cementless acetabular cups. Pre-clinical finite element testing of cups typically use a model of a single patient and assume the results can be extrapolated to the general population. This study explored the variability in predicted primary stability of a Pinnacle® cementless acetabular cup in 103 patient-specific finite element models of the hemipelvis and examined the association between patient-related factors and the observed variability. Cups were inserted by displacement-control into the FE models and then a loading configuration simulating a complete level gait cycle was applied. The cohort showed a range of polar gap of 284-1112 μm and 95th percentile composite peak micromotion (CPM) of 18-624 μm. Regression analysis was not conclusive on the relationship between patient-related factors and primary stability. No relationship was found between polar gap and micromotion. However, when the patient-related factors were categorised into quartile groups, trends suggested higher polar gaps occurred in subjects with small and shallow acetabular geometries and cup motion during gait was affected most by low elastic modulus and high bodyweight. The variation in primary stability in the cohort for an acetabular cup with a proven clinical track record may provide benchmark data when evaluating new cup designs. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1012-1023, 2018.
Collapse
Affiliation(s)
- Dermot O'Rourke
- Medical Device Research Institute, Flinders University, Adelaide, Australia
| | - Rami Ma Al-Dirini
- Medical Device Research Institute, Flinders University, Adelaide, Australia
| | - Mark Taylor
- Medical Device Research Institute, Flinders University, Adelaide, Australia
| |
Collapse
|
14
|
Otto Aufranc Award: Crosslinking Reduces THA Wear, Osteolysis, and Revision Rates at 15-year Followup Compared With Noncrosslinked Polyethylene. Clin Orthop Relat Res 2018; 476. [PMID: 29529656 PMCID: PMC6259699 DOI: 10.1007/s11999.0000000000000036] [Citation(s) in RCA: 68] [Impact Index Per Article: 11.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 01/31/2023]
Abstract
BACKGROUND Crosslinked polyethylene (XLPE) liners used for primary THA have demonstrated lower wear rates than noncrosslinked, conventional polyethylene (CPE) liners through the first decade of clinical service. However, little high-quality evidence is currently available regarding the second decade performance of these implants and it remains uncertain whether the onset of osteolysis has simply been delayed or if the wear associated with XLPE liners will remain low enough that osteolysis will not occur. It is also unknown how the potential reductions in wear and osteolysis will influence long-term revision rates. QUESTIONS/PURPOSES Do patients who underwent THA with XLPE liners demonstrate (1) a lower rate of revision for wear-related complications; (2) a reduced wear rate; and (3) a lower frequency of osteolysis compared with those with CPE liners? METHODS Over an 18-month period from 1999 to 2000, 226 patients who had 236 primary THAs consented to participate in a randomized controlled trial conducted at one institution. To be eligible for intraoperative randomization, patients had to be implanted with a 28-mm cobalt-chrome alloy femoral head, a 4-mm lateralized liner, and the same cup and stem design. Six patients with six THAs were excluded intraoperatively because they did not receive study components for reasons unrelated to the liner material. The remaining 230 THAs among 220 patients were randomized to XLPE liners or CPE liners. The mean age at surgery was 62 ± 11 years and there were no differences in age, gender, or body mass index among the groups. There was no differential loss to followup between the study groups; among patients not known to be deceased or having undergone revision, minimum 14-year radiographic followup is available for 85 THAs including 46 with XLPE and 39 with CPE liners. Polyethylene wear was measured radiographically using Martell's Hip Analysis Suite and areas of osteolysis were evaluated before revision or at most recent followup. Revision rates at 15 years using reoperation for any reason and revision for wear or osteolysis were calculated using cumulative incidence considering patient death as a competing risk. RESULTS The cumulative incidence of revision at 15 years using reoperation for wear-related complications as an endpoint was lower in the XLPE group than the CPE group (0%, 95% confidence interval [CI], 0%-0% versus 12%, 95% CI, 7%-19%; p < 0.001). Among unrevised THAs with minimum 14-year radiographic followup, the mean steady-state linear wear rate for THAs with XLPE liners was lower than the mean linear wear rate for the THAs with CPE liners (0.03 ± 0.05 versus 0.17 ± 0.09 mm/year; mean difference, 0.14; 95% CI, 0.11-0.17; p < 0.001). Osteolysis of any size was noted among 9% (four of 46) of the hips in the XLPE group and 46% (18 of 39) of the hips in the CPE group (odds ratio, 0.19; 95% CI, 0.07-0.51; p < 0.001). CONCLUSIONS This randomized study with followup into the second decade demonstrated reductions in revision, wear, and osteolysis associated with the use of XLPE. The low wear rates and absence of any mechanical failures among the XLPE liners at long-term followup affirm the durability of these components that did not incorporate antioxidants. Although osteolysis has not been eliminated, it occurs infrequently and has not caused any clinical problems to date. LEVEL OF EVIDENCE Level I, therapeutic study.
Collapse
|
15
|
Ali M, Al-Hajjar M, Partridge S, Williams S, Fisher J, Jennings LM. Influence of hip joint simulator design and mechanics on the wear and creep of metal-on-polyethylene bearings. Proc Inst Mech Eng H 2018; 230:389-97. [PMID: 27160559 PMCID: PMC4873727 DOI: 10.1177/0954411915620454] [Citation(s) in RCA: 13] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/13/2015] [Accepted: 11/11/2015] [Indexed: 12/28/2022]
Abstract
Hip joint simulators are used extensively for preclinical testing of hip replacements. The variation in simulator design and test conditions used worldwide can affect the tribological performance of polyethylene. The aim of this study was to assess the effects of simulator mechanics and design on the wear and creep of ultra-high-molecular-weight polyethylene. In the first part of this study, an electromechanical simulator and pneumatic simulator were used to compare the wear and creep of metal-on-polyethylene components under the same standard gait conditions. In the second part of the study, the same electromechanical hip joint simulator was used to investigate the influence of kinematics on wear. Higher wear rates and penetration depths were observed from the electromechanical simulator compared with the pneumatic simulator. When adduction/abduction was introduced to the gait cycle, there was no significant difference in wear with that obtained under the gait cycle condition without adduction/abduction. This study confirmed the influence of hip simulator design and loading conditions on the wear of polyethylene, and therefore direct comparisons of absolute wear rates between different hip joint simulators should be avoided. This study also confirmed that the resulting wear path was the governing factor in obtaining clinically relevant wear rates, and this can be achieved with either two axes or three axes of rotations. However, three axes of rotation (with the inclusion of adduction/abduction) more closely replicate clinical conditions and should therefore be the design approach for newly developed hip joint simulators used for preclinical testing.
Collapse
Affiliation(s)
- Murat Ali
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK
| | - Mazen Al-Hajjar
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK
| | - Susan Partridge
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK
| | - Sophie Williams
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK
| | - John Fisher
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK Leeds Musculoskeletal Biomedical Research Unit, The Leeds Teaching Hospital NHS Trust, University of Leeds, Leeds, UK
| | - Louise M Jennings
- Institute of Medical and Biological Engineering, School of Mechanical Engineering, University of Leeds, Leeds, UK
| |
Collapse
|
16
|
Abstract
Metal-on-highly cross-linked polyethylene is considered the preferred bearing surface for conventional total hip arthroplasty because of its safety profile and excellent results in the first 10 to 15 years of use. However, with younger patient age, activity expectations increase, and the life expectancy of patients with total hip arthroplasty also has increased, so interest remains in other bearing couples. These other options include the use of various ceramic composites for the femoral head on highly cross-linked polyethylene, the so-called second-generation antioxidant polyethylenes, and ceramic acetabular liners. Several of these bearing couples have shown excellent wear rates in vitro, and short-term clinical studies have demonstrated favorable wear and safety results. It is uncertain whether any of these bearing couples should be adopted at present. Understanding the unique properties and possible complications of these bearing couples is critical for appropriate implant selection.
Collapse
|
17
|
Wear rate and medium-term survival of a cemented, moderately cross-linked polyethylene acetabular prosthesis. Hip Int 2018; 28:53-58. [PMID: 29192734 DOI: 10.5301/hipint.5000521] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/04/2023]
Abstract
INTRODUCTION The moderately cross-linked Depuy Marathon® cemented acetabular component was introduced into the UK in 2007. The wear rate for the previously introduced Marathon® uncemented acetabular component has been reported to range from 0.06 to 0.01 mm/year. The aim of this study was to present the medium-term results and wear rate of the Marathon® cemented prosthesis used in primary total hip arthroplasty. METHODS 103 Marathon® cemented acetabular components were implanted between 2008 and 2009 in primary arthroplasty, who were eligible for this study. All patients received a metal 28-mm head. Mean age was 68 years (range 27-87). Mean clinical follow-up was 55 months (range 50-61). Mean radiological follow-up was 46 months (range 24-57). Wear was calculated on AP radiographs using computer-assisted uni-radiographic technique. RESULTS The mean wear was 0.37 mm (range 0.0-0.78 mm). The wear rate was calculated as 0.03 mm/year (95% confidence interval 0.02-0.06). Postoperative complications included deep vein thrombosis (2%) and dislocation (0.8%); there were no deep infections. There were no revisions for failure of the Marathon® cemented acetabular component. CONCLUSIONS The Marathon® cemented acetabular component demonstrates satisfactory wear rates and survivorship at medium-term follow-up.
Collapse
|
18
|
Highly Cross-Linked Polyethylene Reduces Osteolysis Incidence and Wear-Related Reoperation Rate in Cementless Total Hip Arthroplasty Compared With Conventional Polyethylene at a Mean 12-Year Follow-Up. J Arthroplasty 2017; 32:3771-3776. [PMID: 28734615 DOI: 10.1016/j.arth.2017.06.047] [Citation(s) in RCA: 29] [Impact Index Per Article: 4.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/13/2016] [Revised: 05/18/2017] [Accepted: 06/28/2017] [Indexed: 02/01/2023] Open
Abstract
BACKGROUND A number of studies on total hip arthroplasty have compared highly cross-linked polyethylene (HXLPE) with conventional polyethylene (CPE) liners beyond 10 years. However, the impact of HXLPE on the wear-related reoperation rate is unclear. The purpose of this study was to evaluate the clinical advantage of using a single manufacturer's HXLPE in terms of reducing the reoperation rate. METHODS The study was a follow-up retrospective cohort study over a mean of 12 years that examined patients aged 45-70 years with cementless total hip arthroplasty using a 26-mm-diameter cobalt-chromium head. Sixty-seven patients (79 hips; HXLPE group = 41 hips, CPE group = 38 hips) were evaluated for a minimum 10-year follow-up. Kaplan-Meier survival analysis was performed, with wear-related reoperations and radiographic osteolysis serving as the end points. The polyethylene wear rate was also assessed. RESULTS The mean 12-year follow-up rates of survivorship that were evaluated using wear-related reoperations as the end point were 100% and 91.4% in the HXLPE and CPE groups, respectively (P = .007), and the mean 12-year follow-up rates of survivorship with osteolysis as the end point were 100% and 36.2%, respectively (P < .001). Compared with the CPE group, the HXLPE group presented a significantly reduced wear rate (HXLPE group, 0.035 mm/y; CPE group, 0.118 mm/y). CONCLUSION A unique strength of this study is that we assessed a single manufacturer's HXLPE while keeping most other implant parameters uniform. This study reveals the clinical advantage of using a single manufacturer's HXLPE in terms of a reduced wear-related reoperation rate at a mean 12-year follow-up.
Collapse
|
19
|
Kindsfater K, Lesko J. Survivorship of a modular acetabular cup system: medium- to long-term follow-up. Arthroplast Today 2017; 4:376-382. [PMID: 30186925 PMCID: PMC6123169 DOI: 10.1016/j.artd.2017.07.001] [Citation(s) in RCA: 11] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/22/2017] [Revised: 06/30/2017] [Accepted: 07/03/2017] [Indexed: 11/25/2022] Open
Abstract
Background Total hip arthroplasty (THA) requires components that meet a variety of patient factors and needs. This investigation evaluated survivorship of the PINNACLE Acetabular Cup System in primary total hip arthroplasty at 5-10 years. Methods In total, 1592 hips (1473 subjects) were enrolled in a multi-center, non-comparative, open-label study of the PINNACLE system: N = 896 metal-on-polyethylene (MOP), N = 667 metal-on-metal (MOM), N = 27 ceramic-on-polyethylene, and N = 2 unknown articulation. Harris Hip Score, Short Form 36, Western Ontario and McMaster Universities Osteoarthritis Index, and radiographs were collected through 10 years. Kaplan-Meier device survivorship was estimated. Results There were 41 revisions (23 MOP, 17 MOM, 1 ceramic-on-polyethylene) through 10 years: 56.5% of MOP revisions were for instability and 41.2% of MOM revisions were for adverse local tissue reaction. Kaplan-Meier device survivorship (N with further follow-up) was 97.0% (N = 720) at 5 years and 94.7% (N = 77) at 10 years. Conclusions Medium- to long-term survivorship estimates were similar or better than other studies and registries for the PINNACLE system. Level of Evidence III.
Collapse
Affiliation(s)
- Kirk Kindsfater
- Orthopaedic and Spine Center of the Rockies, Fort Collins, CO, USA
| | - Jim Lesko
- DePuy Synthes Joint Reconstruction, Warsaw, IN, USA
- Corresponding author. PO Box 988, 700 Orthopaedic Drive, Warsaw, IN 46581-0988, USA. Tel.: +1 574 372 5901.
| |
Collapse
|
20
|
Metal-on-Metal Total Hip Arthroplasty at Five to Twelve Years Follow-Up: A Concise Follow-Up of a Previous Report. J Arthroplasty 2016; 31:1773-8. [PMID: 27113940 DOI: 10.1016/j.arth.2016.01.058] [Citation(s) in RCA: 12] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/23/2015] [Revised: 01/12/2016] [Accepted: 01/28/2016] [Indexed: 02/01/2023] Open
Abstract
BACKGROUND Concern has arisen regarding potential complications with modular metal-on-metal (MoM) acetabular components in total hip arthroplasty. The purpose of this study was to analyze longitudinally the longer term results of a previously reported cohort of patients utilizing a cementless modular acetabular component with a MoM bearing. METHODS One hundred sixty-nine consecutive but selected total hip arthroplasties were performed in 148 patients at 2 institutions using a modular acetabular MoM component. One hundred thirty-nine patients (158 hips) were living at minimum 5 years, 1 patient (1 hip) was lost to follow-up and 8 patients (10 hips) were deceased. Patients were evaluated clinically in terms of revision as well as radiographically. Additional testing (metal ion levels, advanced imaging) was performed when concerns for adverse local tissue reaction (ALTR) arose. RESULTS There were 6 (3.8%) additional hips revised since the prior report for a total of 7 hips (4.4%) revised at 5-12 year follow-up. All newly revised hips (3.8%) demonstrated ALTR. There were 7 (4.7%) additional cases of radiographically detected acetabular osteolysis and 7 (4.7%) cases of femoral osteolysis. CONCLUSION Longitudinal evaluation of a modular MoM bearing surface acetabular component demonstrated increased rates of ALTR and osteolysis at longer duration follow-up. Although greater than 95% of hips in this study performed well at 5-12 years, when comparing the results to metal-on-polyethylene bearings using the same acetabular component, the results were inferior. Longitudinal surveillance is warranted with this design and this bearing surface couple as cases of ALTR and osteolysis increased with longer follow-up.
Collapse
|
21
|
Woerner M, Sendtner E, Springorum R, Craiovan B, Worlicek M, Renkawitz T, Grifka J, Weber M. Visual intraoperative estimation of cup and stem position is not reliable in minimally invasive hip arthroplasty. Acta Orthop 2016; 87:225-30. [PMID: 26848628 PMCID: PMC4900086 DOI: 10.3109/17453674.2015.1137182] [Citation(s) in RCA: 23] [Impact Index Per Article: 2.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 01/31/2023] Open
Abstract
Background and purpose - In hip arthroplasty, acetabular inclination and anteversion-and also femoral stem torsion-are generally assessed by eye intraoperatively. We assessed whether visual estimation of cup and stem position is reliable. Patients and methods - In the course of a subgroup analysis of a prospective clinical trial, 65 patients underwent cementless hip arthroplasty using a minimally invasive anterolateral approach in lateral decubitus position. Altogether, 4 experienced surgeons assessed cup position intraoperatively according to the operative definition by Murray in the anterior pelvic plane and stem torsion in relation to the femoral condylar plane. Inclination, anteversion, and stem torsion were measured blind postoperatively on 3D-CT and compared to intraoperative results. Results - The mean difference between the 3D-CT results and intraoperative estimations by eye was -4.9° (-18 to 8.7) for inclination, 9.7° (-16 to 41) for anteversion, and -7.3° (-34 to 15) for stem torsion. We found an overestimation of > 5° for cup inclination in 32 hips, an overestimation of > 5° for stem torsion in 40 hips, and an underestimation < 5° for cup anteversion in 42 hips. The level of professional experience and patient characteristics had no clinically relevant effect on the accuracy of estimation by eye. Altogether, 46 stems were located outside the native norm of 10-20° as defined by Tönnis, measured on 3D-CT. Interpretation - Even an experienced surgeon's intraoperative estimation of cup and stem position by eye is not reliable compared to 3D-CT in minimally invasive THA. The use of mechanical insertion jigs, intraoperative fluoroscopy, or imageless navigation is recommended for correct implant insertion.
Collapse
|
22
|
Yan Y, Chen H, Feng J, Chen K, Zhou K, Hong W, Wang Y, Liu Z, Zhang J, Yang Q, Guo L, He C. Poor performance of Enduron polyethylene liner in total hip arthroplasty: a minimum ten-year follow up and ultra-morphological analysis of wear particles. INTERNATIONAL ORTHOPAEDICS 2016; 41:723-730. [PMID: 27178441 DOI: 10.1007/s00264-016-3217-0] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/02/2016] [Accepted: 04/25/2016] [Indexed: 11/29/2022]
Abstract
PURPOSE The aim of the present study was to investigate the long-term outcome and the wear characteristics of two distinct types of ultra-high molecular weight polyethylene (UHMWPE) liners in total hip arthroplasty (THA). METHODS We conducted a retrospective clinical study on patients which were treated with total hip arthroplasty using either Enduron polyethylene (Enduron PE) or Trilogy polyethylene (Trilogy PE) liners based on a minimum of ten year follow up data. Morphological analyses of wear particles from tissue samples, which were harvested during revision surgeries, were also performed. RESULTS A total of 79 THAs in the Enduron group and 55 THAs in the Trilogy group were available for analysis. Kaplan-Meier survival with revision for wear-related complications as the endpoint of the Enduron PE liners was lower than that of Trilogy PE liners at ten years (93.5 % and 100 %, P = 0.03). The Enduron group had higher mean linear wear rate than that of the Trilogy group (0.20 ± 0.09 and 0.09 ± 0.03 mm/year, P < 0.01). The incidence of osteolysis for the Enduron group was higher than that of the Trilogy group (33.3 % and 12 %, P = 0.04). Under transmission electron microscopy, the Enduron group had more than 82 % of the particles less than 1.0 μm in size and more than 57 % of the particles less than 0.5 μm. CONCLUSION The long-term performance of Enduron liners was worse than that of Trilogy liners. Further clinical follow-up may be necessary in patients with Enduron PE liners in order to avoid catastrophic complications.
Collapse
Affiliation(s)
- Yufei Yan
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Hao Chen
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Jianmin Feng
- Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Kaizhe Chen
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Kaidi Zhou
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Weixiang Hong
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Yi Wang
- Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Zhihong Liu
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Jiong Zhang
- Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Qingming Yang
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China.,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China
| | - Lei Guo
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China. .,Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, China.
| | - Chuan He
- Shanghai Key Laboratory for Prevention and Treatment of Bone and Joint Diseases, Shanghai Institute of Traumatology and Orthopaedics, Shanghai, China. .,Department of Orthopaedics, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, 197 Ruijin 2nd Road, Shanghai, 200025, People's Republic of China.
| |
Collapse
|
23
|
Garvin KL, White TC, Dusad A, Hartman CW, Martell J. Low wear rates seen in THAs with highly crosslinked polyethylene at 9 to 14 years in patients younger than age 50 years. Clin Orthop Relat Res 2015; 473:3829-35. [PMID: 26122983 PMCID: PMC4626518 DOI: 10.1007/s11999-015-4422-7] [Citation(s) in RCA: 46] [Impact Index Per Article: 5.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 01/31/2023]
Abstract
BACKGROUND Patients 50 years or younger are at high risk for wear-related complications of their total hip arthroplasty (THA) because of their generally higher levels of activity. Highly crosslinked polyethylene (HXLPE) is believed to be more durable for this population than conventional polyethylene because of its improved wear; however, limited information is available on the wear of HXLPE in this population, particularly the wear of HXLPE when it articulates with alternative bearings like Oxinium (Smith & Nephew, Memphis, TN, USA). QUESTIONS/PURPOSES The purpose of this study was to evaluate two questions relative to this population of patients undergoing THA. First, what was the linear and volumetric wear rate of HXLPE in patients 50 years or younger at a minimum followup of 9 years and was osteolysis observed in any of these hips? Given the potential for damage to the Oxinium femoral head surface, was the wear of HXLPE in the patients with this material similar to the other bearings or was there accelerated or runaway wear that was visible in any of the patients? METHODS From November 1999 to April 2005, 105 THAs were performed in 95 patients 50 years of age or younger (mean, 42 years; range, 20-50 years). The mean body mass index was 30 kg/m(2) (range, 17-51 kg/m(2)).The mean followup was 12 years (range, 9-14 years). Two patients died, five patients (one bilateral) were lost to followup, and one hip was revised elsewhere for pain. The patients' information was not included in the study, which left 87 patients with 96 hips for analysis. Highly crosslinked polyethylene was the acetabular bearing for all of the hips. We analyzed the linear and volumetric wear of all of the hips using the Martell method. Eighty hips had the same diameter head (28 mm) allowing us to more accurately compare the different bearing materials. The type of femoral head used was related to our sequential use of materials beginning with cobalt chrome (14), ceramic (23) followed by Oxinium (43) in the hips with 28-mm heads. Although cobalt-chrome was used early in this study, our previous experience with ceramic on polyethylene encouraged us to use it as an alternative bearing. The Oxinium was used consecutively for the remaining hips. RESULTS The mean wear of the HXLPE after 1 year of bedding-in (true linear wear)was 0.022 mm/year (95% confidence interval [CI], 0.015-0.030 mm/year). The mean volumetric wear of HXLPE after 1 year of bedding-in (true volumetric wear) was 9 mm(3)/year (95% CI, 4-14 mm(3)/year). None of the hip radiographs had evidence of loosening or osteolysis. Wear was not associated with femoral head material (p = 0.58 for linear wear/year versus head material and p = 0.52 for volumetric wear/year versus head material). CONCLUSIONS In our study of patients 50 years of age or younger undergoing THA, the linear and volumetric wear rates of HXLPE were very low regardless of the bearing surface material. The laboratory concerns of Oxinium surface damage are serious but at this time we have not seen high wear of the HXLPE or osteolysis in this population. LEVEL OF EVIDENCE Level III, therapeutic study.
Collapse
Affiliation(s)
- Kevin L. Garvin
- />Department of Orthopaedic Surgery and Rehabilitation, University of Nebraska Medical Center, 981080 Nebraska Medical Center, Omaha, NE 68198-1080 USA
| | - Tyler C. White
- />Department of Orthopaedic Surgery and Rehabilitation, University of Nebraska Medical Center, 981080 Nebraska Medical Center, Omaha, NE 68198-1080 USA
| | - Anand Dusad
- />Department of Orthopaedic Surgery and Rehabilitation, University of Nebraska Medical Center, 981080 Nebraska Medical Center, Omaha, NE 68198-1080 USA
| | - Curtis W. Hartman
- />Department of Orthopaedic Surgery and Rehabilitation, University of Nebraska Medical Center, 981080 Nebraska Medical Center, Omaha, NE 68198-1080 USA
| | - John Martell
- />The Orthopaedic Research Institute, University of Chicago Medicine, Chicago, IL USA
| |
Collapse
|
24
|
Fixation and Wear With Contemporary Acetabular Components and Cross-Linked Polyethylene at 10-Years in Patients Aged 50 and Under. J Arthroplasty 2015; 30:1577-85. [PMID: 26024989 DOI: 10.1016/j.arth.2015.05.011] [Citation(s) in RCA: 16] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 02/19/2015] [Revised: 04/27/2015] [Accepted: 05/02/2015] [Indexed: 02/01/2023] Open
Abstract
We evaluated the mid-term performance of a moderately cross-linked polyethylene THA bearing in younger patients. One hundred consecutive THAs performed in patients 50 years of age and under using the same cementless acetabular component and moderately cross-linked polyethylene were evaluated at minimum 10 year follow-up. At final follow-up 75 patients (89 hips) were living, 7 patients (7 hips) were deceased and 4 patients (4 hips) were lost to follow-up. Average Tegner and UCLA scores were 3.7 and 5.8, respectively. Average steps per year were 1.84 million. The average linear wear rate was 0.05 mm/y and steady state wear rate was 0.033 mm/y. There was no detectable osteolysis. Minimum 10 year follow-up demonstrated durable fixation and reduced wear (P<0.001) when compared to our historical controls.
Collapse
|
25
|
Zietz C, Fabry C, Baum F, Bader R, Kluess D. The Divergence of Wear Propagation and Stress at Steep Acetabular Cup Positions Using Ceramic Heads and Sequentially Cross-Linked Polyethylene Liners. J Arthroplasty 2015; 30:1458-63. [PMID: 25770865 DOI: 10.1016/j.arth.2015.02.025] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/30/2014] [Revised: 02/17/2015] [Accepted: 02/23/2015] [Indexed: 02/01/2023] Open
Abstract
The aim of the present wear simulator study was to assess the effect of steep acetabular cup positions on the wear propagation of highly cross-linked-PE (HX-PE) liners. Furthermore, a finite element analysis (FEA) was performed in order to calculate the stress within the HX-PE material in case of steep cup positions under physiological loadings. The higher stress in the HX-PE at a steep acetabular cup position did not result in increased wear in the present wear simulator study. The gravimetrical wear rates at normal (45°) and steep cup inclinations (75°) showed wear amounts of 3.15±0.27mg and 2.18±0.31mg per million cycles (p=0.028), respectively. However, FEA revealed clear increase in stress at the HX-PE liners with respect to steep cup positions.
Collapse
Affiliation(s)
- Carmen Zietz
- Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University Medicine Rostock, Rostock, Germany
| | - Christian Fabry
- Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University Medicine Rostock, Rostock, Germany
| | - Felix Baum
- Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University Medicine Rostock, Rostock, Germany
| | - Rainer Bader
- Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University Medicine Rostock, Rostock, Germany
| | - Daniel Kluess
- Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University Medicine Rostock, Rostock, Germany
| |
Collapse
|