Increase in the current variance in bilayer lipid membranes near phase transition as a result of the occurrence of hydrophobic defects

Multiple conductance states of lipid pores during Voltage-Clamp electroporation

We used voltage-clamp electroporation to obtain single-channel recordings of lipid pores and analyzed the idealized dwell-time sequences using Maximum-Likelihood Fitting. We observed traces with multiple current levels and determined whether they were a result of the presence of multiple pores or a single pore with multiple conductance states. We found that, within the same recording, the bilayer can have a single pore with multiple conductance states or multiple independent pores. Using high sampling rates (100 kHz) we were able to observe pores with 40 μs lifetimes, and in experiments using high-voltage pulses we observed the existence of long-lived fluctuations minutes after the removal of the electric field. These results come closer to reconciling the nanosecond lifetime pores in molecular dynamics simulations and the long-lived permeability of cells after electroporation.

Different effects of two Poloxamers (L61 and F68) on the conductance of bilayer lipid membranes

The integral conductance of planar lipid bilayer membranes in the presence of two Poloxamers (Pluronics) L61 and F68 with the same lengths of hydrophobic poly(propylene oxide) blocks and the different lengths of hydrophilic poly(ethylene oxide) blocks increases with an increase in the concentration of both Pluronics; however, the shape of the conductance-concentration curves is super linear for L61 and sublinear for F68. In the presence of both Pluronics, rare discrete current jumps are observed against the background of continuous current. At high concentrations, the I-V curves of membranes with both L61 and F68 became nonlinear at sufficiently low voltages but differed significantly. At voltages greater than 50 mV, the conductance of membranes with L61 increased sharply and quantized jumps were observed toward higher conductance, which could be interpreted as the appearance of additional pores. On the contrary, the conductance of membranes with F68 decreased and quantized jumps to lower conductance were observed, which could be interpreted as blocking of already existing pores. We attributed the differences in the conductance-concentration and I-V curves of these two Pluronics to their different effects on the dynamics of membrane hydration and, accordingly, on the probability of formation of conducting pores.

Advances in pulsed electric stimuli as a physical method for treating liquid foods

There is a need for alternative technologies that can deliver safe and nutritious foods at lower costs as compared to conventional processes. Pulsed electric field (PEF) technology has been utilised for a plethora of different applications in the life and physical sciences, such as gene/drug delivery in medicine and extraction of bioactive compounds in food science and technology. PEF technology for treating liquid foods involves engineering principles to develop the equipment, and quantitative biochemistry and microbiology techniques to validate the process. There are numerous challenges to address for its application in liquid foods such as the 5-log pathogen reduction target in food safety, maintaining the food quality, and scale up of this physical approach for industrial integration. Here, we present the engineering principles associated with pulsed electric fields, related inactivation models of microorganisms, electroporation and electropermeabilization theory, to increase the quality and safety of liquid foods; including water, milk, beer, wine, fruit juices, cider, and liquid eggs. Ultimately, we discuss the outlook of the field and emphasise research gaps.

Water Pores in Planar Lipid Bilayers at Fast and Slow Rise of Transmembrane Voltage

Basic understanding of the barrier properties of biological membranes can be obtained by studying model systems, such as planar lipid bilayers. Here, we study water pores in planar lipid bilayers in the presence of transmembrane voltage. Planar lipid bilayers were exposed to fast and slow linearly increasing voltage and current signals. We measured the capacitance, breakdown voltage, and rupture time of planar lipid bilayers composed of 1-pamitoyl 2-oleoyl phosphatidylcholine (POPC), 1-pamitoyl 2-oleoyl phosphatidylserine (POPS), and a mixture of both lipids in a 1:1 ratio. Based on the measurements, we evaluated the change in the capacitance of the planar lipid bilayer corresponding to water pores, the radius of water pores at membrane rupture, and the fraction of the area of the planar lipid bilayer occupied by water pores.planar lipid bilayer capacitance, which corresponds to water pores, water pore radius at the membrane rupture, and a fraction of the planar lipid bilayer area occupied by water pores. The estimated pore radii determining the rupture of the planar lipid bilayer upon fast build-up of transmembrane voltage are 0.101 nm, 0.110 nm, and 0.106 nm for membranes composed of POPC, POPS, and POPC:POPS, respectively. The fraction of the surface occupied by water pores at the moment of rupture of the planar lipid bilayer The fraction of an area that is occupied by water pores at the moment of planar lipid bilayer rupture is in the range of 0.1–1.8%.

Estimation of the parameters of the Smoluchowski equation describing the occurrence of pores in a bilayer lipid membrane under soft poration

The conductive lipid pores occurring in planar bilayer membranes are known to manifest themselves experimentally as current fluctuations. Reliable recording of such fluctuations during phase transitions, as well as in membranes with various additives (for example, SDS), allows one to determine the characteristics of hypothetical hydrophilic pores, namely, their number, sizes, lifetimes, and duration of time intervals between pores. Because, in contrast with electroporation, the emergence of pores in a membrane does not require high voltages, this process is called soft poration. Studying the characteristics of pores under soft poration allows us to estimate the parameters of the Smoluchowski equation and compare them with the corresponding parameters used to describe electroporation. In this work, the experimental characteristics of current fluctuations in the membrane with the addition of SDS to the bulk solution were used to estimate the parameters of the Smoluchowski equation: the pore edge tension, the energy of the hydrophobic pore/hydrophilic pore barrier, the coefficient of pore diffusion in the radius space, the initial distribution density of the number of pores, and the attempt rate density of the lipids in a membrane. The obtained estimates are close to the parameter values used in studies of electroporation.

Investigation of Start-Up Characteristics of Thermosyphons Modified with Different Hydrophilic and Hydrophobic Inner Surfaces

In this paper, the influence of wettability properties on the start-up characteristics of two-phase closed thermosyphons (TPCTs) is investigated. Chemical coating and etching techniques are performed to prepare the surfaces with different wettabilities that is quantified in the form of the contact angle (CA). The 12 TPCTs are processed including the same CA and a different CA combination on the inner surfaces inside both the evaporator and the condenser sections. For TPCTs with the same wettability properties, the introduction of hydrophilic properties inside the evaporator section not only significantly reduces the start-up time but also decreases the start-up temperature. For example, the start-up time of a TPCT with CA = 28° at 40 W, 60 W and 80 W is 46%, 50% and 55% shorter than that of a TPCT with a smooth surface and the wall superheat degrees is 55%, 39% and 28% lower, respectively. For TPCTs with combined hydrophilic and hydrophobic properties, the start-up time spent on the evaporator section with hydrophilic properties is shorter than that of the hydrophobic evaporator section and the smaller CA on the condenser section shows better results. The start-up time of a TPCT with CA = 28° on the evaporator section and CA = 105° on the condenser section has the best start-up process at 40 W, 60 W and 80 W which is 14%, 22% and 26% shorter than that of a TPCT with smooth surface. Thus, the hydrophilic and hydrophobic modifications play a significant role in promoting the start-up process of a TPCT.