1
|
Kampouraki ZC, Petala M, Zacharias K, Konstantinidis A, Zabulis X, Karamaounas P, Kostoglou M, Karapantsios TD. Highly sensitive resistance spectroscopy technique for online monitoring of biofilm growth on metallic surfaces. ENVIRONMENTAL RESEARCH 2024; 240:117401. [PMID: 37918765 DOI: 10.1016/j.envres.2023.117401] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/03/2023] [Revised: 10/02/2023] [Accepted: 10/11/2023] [Indexed: 11/04/2023]
Abstract
Online techniques for monitoring biofilm formation and evolution are limited, especially as regards its application in flowing water systems. This is chiefly due to the absence of efficient non-destructive and non-invasive sensing methods. In this study, a sensitive electrical resistance spectroscopy technique is developed to monitor non-invasively and in real time the growth of biofilms over metallic surfaces inside water flow systems. To this aim, Pseudomonas fluorescens strain is used for biofilm development lasting 72 h in a laboratory-scale test channel of orthogonal cross section. Biofilm development corresponds to a progressively increasing coverage of the metallic surface area up to full coverage and a progressively increasing thickness. Biofilm development is registered by continuous recording of electrical impedance signals (time series). Proper configuration and tuning of the electronics promote the resistive contribution to the signal whereas careful grounding diminishes electrical interferences and yields superb sensing sensitivity. An increase of relative electrical resistance of around 15% is noticed in 72 h flow experiments which is attributed to both an increase of metallic surface area coverage and an increase of biofilm thickness. An independent estimation of these quantities using imaging tools and microscopy analysis, indicates that full coverage of the metallic surface occurs after only 48 h of the flow experiment, whereas biofilm thickness increases gradually along the entire 72 h of the experiment. Cross-examination of electrical signals with biofilm characteristics (metallic surface coverage and biofilm thickness) reveals that, qualitatively speaking, electrical signals are rather more sensitive to metallic surface coverage than biofilm thickness.
Collapse
Affiliation(s)
- Zoi Christina Kampouraki
- Division of Chemical Technology, School of Chemistry, Aristotle University of Thessaloniki, University Box 116, 541 24, Thessaloniki, Greece
| | - Maria Petala
- Department of Civil Engineering, Aristotle University of Thessaloniki, 541 24, Thessaloniki, Greece
| | - Konstantinos Zacharias
- Division of Chemical Technology, School of Chemistry, Aristotle University of Thessaloniki, University Box 116, 541 24, Thessaloniki, Greece
| | - Avraam Konstantinidis
- Laboratory of Engineering Mechanics, School of Civil Engineering, Aristotle University of Thessaloniki, GR, 541 24, Thessaloniki, Greece
| | - Xenophon Zabulis
- Institute of Computer Science, Foundation for Research and Technology, 711 10, Heraklion, Greece
| | - Polykarpos Karamaounas
- Institute of Computer Science, Foundation for Research and Technology, 711 10, Heraklion, Greece
| | - Margaritis Kostoglou
- Division of Chemical Technology, School of Chemistry, Aristotle University of Thessaloniki, University Box 116, 541 24, Thessaloniki, Greece
| | - Thodoris D Karapantsios
- Division of Chemical Technology, School of Chemistry, Aristotle University of Thessaloniki, University Box 116, 541 24, Thessaloniki, Greece.
| |
Collapse
|
2
|
Liao Y, Fatehi P, Liao B. Microalgae cell adhesions on hydrophobic membrane substrates using quartz crystal microbalance with dissipation. Colloids Surf B Biointerfaces 2023; 230:113514. [PMID: 37598610 DOI: 10.1016/j.colsurfb.2023.113514] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/27/2023] [Revised: 08/03/2023] [Accepted: 08/08/2023] [Indexed: 08/22/2023]
Abstract
Microalgal cell adhesion and biofilm formation are affected by interactions between microalgae strains and membrane materials. Variations of surface properties of microalgae and membrane materials are expected to affect cell-membranes and cell-cell interactions and thus initial microalgal cell adhesion and biofilm formation rates. Hence, it should be possible to identify the dominant mechanisms controlling microalgal cell adhesion and biofilm formation. The effects of surface properties of three different microalgal strains and three different types of membrane materials on microalgal cell adhesion and biofilm formation were systematically investigated in real time by monitoring changes in the oscillation frequency and dissipation of the quartz crystal resonator (QCM-D). The results revealed that in general a higher surface free energy, more negative zeta potential, and higher surface roughness of membrane materials positively correlated with a larger quantity of microalgae cell deposition, while a more hydrophilic microalgae with a larger negative zeta potential preferred to attach to a more hydrophobic membrane material. The adhered microalgal layers exhibited viscoelastic properties. The relative importance of these mechanisms in controlling microalgae cell attachment and biofilm formation might vary, depending on the properties of specific microalgae species and hydrophobic membrane materials used.
Collapse
Affiliation(s)
- Yichen Liao
- Department of Chemical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B5E1, Canada
| | - Pedram Fatehi
- Department of Chemical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B5E1, Canada
| | - Baoqiang Liao
- Department of Chemical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B5E1, Canada.
| |
Collapse
|
3
|
Ripa R, Shen AQ, Funari R. Detecting Escherichia coli Biofilm Development Stages on Gold and Titanium by Quartz Crystal Microbalance. ACS OMEGA 2020; 5:2295-2302. [PMID: 32064391 PMCID: PMC7017401 DOI: 10.1021/acsomega.9b03540] [Citation(s) in RCA: 11] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/22/2019] [Accepted: 12/26/2019] [Indexed: 05/03/2023]
Abstract
Bacterial biofilms are responsible for persistent infections and biofouling, raising serious concerns in both medical and industrial processes. These motivations underpin the need to develop methodologies to study the complex biological structures of biofilms and prevent their formation on medical implants, tools, and industrial apparatuses. Here, we report the detailed comparison of Escherichia coli biofilm development stages (adhesion, maturation, and dispersion) on gold and titanium surfaces by monitoring the changes in both frequency and dissipation of a quartz crystal microbalance (QCM) device, a cheap and reliable microgravimetric sensor which allows the real-time and label-free characterization of various stages of biofilm development. Although gold is the most common electrode material used for QCM sensors, the titanium electrode is also readily available for QCM sensors; thus, QCM sensors with different metal electrodes serve as a simple platform to probe how pathogens interact with different metal substrates. The QCM outcomes are further confirmed by atomic force microscopy and crystal violet staining, thus validating the effectiveness of this surface sensitive sensor for microbial biofilm research. Moreover, because QCM technology can easily modify the substrate types and coatings, QCM sensors also provide well-controlled experimental conditions to study antimicrobial surface treatments and eradication procedures, even on mature biofilms.
Collapse
Affiliation(s)
- Rosa Ripa
- Micro/Bio/Nanofluidics Unit, Okinawa Institute of Science and Technology Graduate
University, 1919-1 Tancha, Onna-son, Okinawa 904-0495, Japan
| | - Amy Q. Shen
- Micro/Bio/Nanofluidics Unit, Okinawa Institute of Science and Technology Graduate
University, 1919-1 Tancha, Onna-son, Okinawa 904-0495, Japan
| | - Riccardo Funari
- Micro/Bio/Nanofluidics Unit, Okinawa Institute of Science and Technology Graduate
University, 1919-1 Tancha, Onna-son, Okinawa 904-0495, Japan
| |
Collapse
|
4
|
Li G, Wu Y, Li Y, Hong Y, Zhao X, Reyes PI, Lu Y. Early stage detection of Staphylococcus epidermidis biofilm formation using MgZnO dual-gate TFT biosensor. Biosens Bioelectron 2019; 151:111993. [PMID: 31999592 DOI: 10.1016/j.bios.2019.111993] [Citation(s) in RCA: 11] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/27/2019] [Revised: 12/04/2019] [Accepted: 12/23/2019] [Indexed: 12/20/2022]
Abstract
Early stage detection of biofilm formation is an important aspect of microbial research because once formed, biofilms show serious tolerance to antibiotics in contrast to the free-floating bacteria, which significantly increases the difficulty for clinical treatment of bacterial infections. The early stage detection technology is desired to improve the efficiency of medical treatments. In this work, we present a biosensor consisting of a magnesium zinc oxide (MZO) dual gate thin-film transistor (DGTFT) as the actuator and an MZO nanostructure (MZOnano) array coated conducting pad as the extended sensing gate for the early stage detection of Staphylococcus epidermidis (S. epidermidis) biofilm formation. S. epidermidis bacteria were cultured in vitro on the nanostructure modified sensing pad. Charge transfer occurs between microbial cells and the MZOnano during the initial bacterial adhesion stage. Such electrical signals, which represent the onset of biofilm formation, were dynamically detected by the DGTFT where the top gate electrode was connected to the extended MZOnano sensing pad and the bottom gate was used for biasing the device into the optimum characteristic region for high sensitivity and stable operation. The testing results show that a current change of ~80% is achieved after ~200 min of bacterial culturing. A crystal violet staining-based assay shows that tiny bacterial microcolonies just start to form at 200 min, and that it would take approximately 24 h to form matured biofilms. This technology enables medical professionals to act promptly on bacterial infection before biofilms get fully established.
Collapse
Affiliation(s)
- Guangyuan Li
- Department of Electrical and Computer Engineering, Rutgers University, Piscataway, NJ, 08854-8058, United States
| | - Yifan Wu
- Department of Electrical and Computer Engineering, Rutgers University, Piscataway, NJ, 08854-8058, United States
| | - Yuxuan Li
- Department of Electrical and Computer Engineering, Rutgers University, Piscataway, NJ, 08854-8058, United States
| | - Yuzhi Hong
- Public Health Research Institute and Department of Microbiology, Biochemistry & Molecular Genetics, New Jersey Medical School, Rutgers University, Newark, NJ, 07103-3535, United States
| | - Xilin Zhao
- Public Health Research Institute and Department of Microbiology, Biochemistry & Molecular Genetics, New Jersey Medical School, Rutgers University, Newark, NJ, 07103-3535, United States
| | - Pavel Ivanoff Reyes
- Department of Electrical and Computer Engineering, Rutgers University, Piscataway, NJ, 08854-8058, United States.
| | - Yicheng Lu
- Department of Electrical and Computer Engineering, Rutgers University, Piscataway, NJ, 08854-8058, United States.
| |
Collapse
|
5
|
QCM-D characterization of time-dependence of bacterial adhesion. ACTA ACUST UNITED AC 2019; 5:100024. [PMID: 32743140 PMCID: PMC7389184 DOI: 10.1016/j.tcsw.2019.100024] [Citation(s) in RCA: 36] [Impact Index Per Article: 7.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/16/2018] [Revised: 01/29/2019] [Accepted: 03/29/2019] [Indexed: 12/22/2022]
Abstract
Quartz crystal microbalance with dissipation monitoring (QCM-D) is becoming an increasingly popular technique that can be employed as part of experimental and modeling investigations of bacterial adhesion. The usefulness of QCM-D derives from this technique's ability to probe binding and interactions under dynamic conditions, in real time. Bacterial adhesion is an important first step in the formation of biofilms, the control of which is relevant to industries that include shipping, water purification, packaging, and biomedical devices. However, many questions remain unanswered in the bacterial adhesion process, despite extensive research in this area. With QCM-D, multiple variables affecting bacterial adhesion can be studied, including the roles of substrate composition, chemical modification, solution ionic strength, environmental temperature, shear conditions, and time. Recent studies demonstrate the utility of QCM-D in developing new bacterial adhesion models and studying different stages of biofilm formation. We provide a review of how QCM-D has been used to study bacterial adhesion at stages ranging from the first step of bacterial adhesion to mature biofilms, and how QCM-D studies are being used to promote the development of solutions to biofilm formation.
Collapse
|
6
|
Optimization and in Silico Analysis of a Cold-Adapted Lipase from an Antarctic Pseudomonas sp. Strain AMS8 Reaction in Triton X-100 Reverse Micelles. Catalysts 2018. [DOI: 10.3390/catal8070289] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022] Open
Abstract
A moderate yield of a purified enzyme can be achieved by using the simple technique of reverse micellar extraction (RME). RME is a liquid–liquid extraction method that uses a surfactant and an organic solvent to extract biomolecules. Instead of traditional chromatographic purification methods, which are tedious and expensive, RME using the nonionic surfactant Triton X-100 and toluene is used as an alternative purification technique to purify a recombinant cold-adapted lipase, AMS8. Various process parameters were optimized to maximize the activity recovery of the AMS8 lipase. The optimal conditions were found to be 50 mM sodium phosphate buffer, pH 7, 0.125 M NaCl, and 0.07 M Triton X-100 in toluene at 10 °C. Approximately 56% of the lipase activity was successfully recovered. Structural analysis of the lipase in a reverse micelle (RM) was performed using an in silico approach. The predicted model of AMS8 lipase was simulated in the Triton X-100/toluene reverse micelles from 5 to 40 °C. The lid 2 was slightly opened at 10 °C. However, the secondary structure of AMS8 was most affected in the non-catalytic domain compared to the catalytic domain, with an increased coil conformation. These results suggest that an AMS8 lipase can be extracted using Triton X-100/water/toluene micelles at low temperature. This RME approach will be an important tool for the downstream processing of recombinant cold-adapted lipases.
Collapse
|
7
|
Phinney DM, Goode KR, Fryer PJ, Heldman D, Bakalis S. Identification of residual nano-scale foulant material on stainless steel using atomic force microscopy after clean in place. J FOOD ENG 2017. [DOI: 10.1016/j.jfoodeng.2017.06.019] [Citation(s) in RCA: 6] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/19/2022]
|
8
|
Huang R, Yi P, Tang Y. Probing the interactions of organic molecules, nanomaterials, and microbes with solid surfaces using quartz crystal microbalances: methodology, advantages, and limitations. ENVIRONMENTAL SCIENCE. PROCESSES & IMPACTS 2017; 19:793-811. [PMID: 28488712 DOI: 10.1039/c6em00628k] [Citation(s) in RCA: 12] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/07/2023]
Abstract
Quartz crystal microbalances (QCMs) provide a new analytical opportunity and prospect to characterize many environmental processes at solid/liquid interfaces, thanks to their almost real-time measurement of physicochemical changes on their quartz sensor. This work reviews the applications of QCMs in probing the interactions of organic molecules, nanomaterials (NMs) and microbes with solid surfaces. These interfacial interactions are relevant to critical environmental processes such as biofilm formation, fate and transport of NMs, fouling in engineering systems and antifouling practices. The high sensitivity, real-time monitoring, and simultaneous frequency and dissipation measurements make QCM-D a unique technique that helps reveal the interaction mechanisms for the abovementioned processes (e.g., driving forces, affinity, kinetics, and the interplay between surface chemistry and solution chemistry). On the other hand, QCM measurement is nonselective and spatially-dependent. Thus, caution should be taken during data analysis and interpretation, and it is necessary to cross-validate the results using complementary information from other techniques for more quantitative and accurate interpretation. This review summarizes the general methodologies for collecting and analyzing raw QCM data, as well as for evaluating the associated uncertainties. It serves to help researchers gain deeper insights into the fundamentals and applications of QCMs, and provides new perspectives on future research directions.
Collapse
Affiliation(s)
- Rixiang Huang
- School of Earth and Atmospheric Sciences, Georgia Institute of Technology, 311 Ferst Dr, Atlanta, Georgia 30324-0340, USA.
| | | | | |
Collapse
|
9
|
Olsson AL, Mitzel MR, Tufenkji N. QCM-D for non-destructive real-time assessment of Pseudomonas aeruginosa biofilm attachment to the substratum during biofilm growth. Colloids Surf B Biointerfaces 2015; 136:928-34. [DOI: 10.1016/j.colsurfb.2015.10.032] [Citation(s) in RCA: 24] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/16/2015] [Revised: 10/02/2015] [Accepted: 10/20/2015] [Indexed: 12/20/2022]
|
10
|
Bragazzi NL, Amicizia D, Panatto D, Tramalloni D, Valle I, Gasparini R. Quartz-Crystal Microbalance (QCM) for Public Health: An Overview of Its Applications. ADVANCES IN PROTEIN CHEMISTRY AND STRUCTURAL BIOLOGY 2015; 101:149-211. [PMID: 26572979 DOI: 10.1016/bs.apcsb.2015.08.002] [Citation(s) in RCA: 26] [Impact Index Per Article: 2.9] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/12/2022]
Abstract
Nanobiotechnologies, from the convergence of nanotechnology and molecular biology and postgenomics medicine, play a major role in the field of public health. This overview summarizes the potentiality of piezoelectric sensors, and in particular, of quartz-crystal microbalance (QCM), a physical nanogram-sensitive device. QCM enables the rapid, real time, on-site detection of pathogens with an enormous burden in public health, such as influenza and other respiratory viruses, hepatitis B virus (HBV), and drug-resistant bacteria, among others. Further, it allows to detect food allergens, food-borne pathogens, such as Escherichia coli and Salmonella typhimurium, and food chemical contaminants, as well as water-borne microorganisms and environmental contaminants. Moreover, QCM holds promises in early cancer detection and screening of new antiblastic drugs. Applications for monitoring biohazards, for assuring homeland security, and preventing bioterrorism are also discussed.
Collapse
Affiliation(s)
- Nicola Luigi Bragazzi
- Department of Health Sciences (DISSAL), Via Antonio Pastore 1, University of Genoa, Genoa, Italy
| | - Daniela Amicizia
- Department of Health Sciences (DISSAL), Via Antonio Pastore 1, University of Genoa, Genoa, Italy
| | - Donatella Panatto
- Department of Health Sciences (DISSAL), Via Antonio Pastore 1, University of Genoa, Genoa, Italy
| | - Daniela Tramalloni
- Department of Health Sciences (DISSAL), Via Antonio Pastore 1, University of Genoa, Genoa, Italy
| | - Ivana Valle
- SSD "Popolazione a rischio," Health Prevention Department, Local Health Unit ASL3 Genovese, Genoa, Italy
| | - Roberto Gasparini
- Department of Health Sciences (DISSAL), Via Antonio Pastore 1, University of Genoa, Genoa, Italy.
| |
Collapse
|
11
|
Hohmann S, Kögel S, Brunner Y, Schmieg B, Ewald C, Kirschhöfer F, Brenner-Weiß G, Länge K. Surface Acoustic Wave (SAW) Resonators for Monitoring Conditioning Film Formation. SENSORS 2015; 15:11873-88. [PMID: 26007735 PMCID: PMC4481949 DOI: 10.3390/s150511873] [Citation(s) in RCA: 20] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/02/2015] [Accepted: 05/17/2015] [Indexed: 01/20/2023]
Abstract
We propose surface acoustic wave (SAW) resonators as a complementary tool for conditioning film monitoring. Conditioning films are formed by adsorption of inorganic and organic substances on a substrate the moment this substrate comes into contact with a liquid phase. In the case of implant insertion, for instance, initial protein adsorption is required to start wound healing, but it will also trigger immune reactions leading to inflammatory responses. The control of the initial protein adsorption would allow to promote the healing process and to suppress adverse immune reactions. Methods to investigate these adsorption processes are available, but it remains difficult to translate measurement results into actual protein binding events. Biosensor transducers allow user-friendly investigation of protein adsorption on different surfaces. The combination of several transduction principles leads to complementary results, allowing a more comprehensive characterization of the adsorbing layer. We introduce SAW resonators as a novel complementary tool for time-resolved conditioning film monitoring. SAW resonators were coated with polymers. The adsorption of the plasma proteins human serum albumin (HSA) and fibrinogen onto the polymer-coated surfaces were monitored. Frequency results were compared with quartz crystal microbalance (QCM) sensor measurements, which confirmed the suitability of the SAW resonators for this application.
Collapse
Affiliation(s)
- Siegfried Hohmann
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
- Institute of Functional Interfaces, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Svea Kögel
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Yvonne Brunner
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Barbara Schmieg
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Christina Ewald
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Frank Kirschhöfer
- Institute of Functional Interfaces, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Gerald Brenner-Weiß
- Institute of Functional Interfaces, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| | - Kerstin Länge
- Institute of Microstructure Technology, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany.
| |
Collapse
|
12
|
Ying W, Siebdrath N, Uhl W, Gitis V, Herzberg M. New insights on early stages of RO membranes fouling during tertiary wastewater desalination. J Memb Sci 2014. [DOI: 10.1016/j.memsci.2014.04.027] [Citation(s) in RCA: 48] [Impact Index Per Article: 4.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
|
13
|
Lüdecke C, Jandt KD, Siegismund D, Kujau MJ, Zang E, Rettenmayr M, Bossert J, Roth M. Reproducible biofilm cultivation of chemostat-grown Escherichia coli and investigation of bacterial adhesion on biomaterials using a non-constant-depth film fermenter. PLoS One 2014; 9:e84837. [PMID: 24404192 PMCID: PMC3880331 DOI: 10.1371/journal.pone.0084837] [Citation(s) in RCA: 30] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/06/2013] [Accepted: 11/19/2013] [Indexed: 02/02/2023] Open
Abstract
Biomaterials-associated infections are primarily initiated by the adhesion of microorganisms on the biomaterial surfaces and subsequent biofilm formation. Understanding the fundamental microbial adhesion mechanisms and biofilm development is crucial for developing strategies to prevent such infections. Suitable in vitro systems for biofilm cultivation and bacterial adhesion at controllable, constant and reproducible conditions are indispensable. This study aimed (i) to modify the previously described constant-depth film fermenter for the reproducible cultivation of biofilms at non-depth-restricted, constant and low shear conditions and (ii) to use this system to elucidate bacterial adhesion kinetics on different biomaterials, focusing on biomaterials surface nanoroughness and hydrophobicity. Chemostat-grown Escherichia coli were used for biofilm cultivation on titanium oxide and investigating bacterial adhesion over time on titanium oxide, poly(styrene), poly(tetrafluoroethylene) and glass. Using chemostat-grown microbial cells (single-species continuous culture) minimized variations between the biofilms cultivated during different experimental runs. Bacterial adhesion on biomaterials comprised an initial lag-phase I followed by a fast adhesion phase II and a phase of saturation III. With increasing biomaterials surface nanoroughness and increasing hydrophobicity, adhesion rates increased during phases I and II. The influence of materials surface hydrophobicity seemed to exceed that of nanoroughness during the lag-phase I, whereas it was vice versa during adhesion phase II. This study introduces the non-constant-depth film fermenter in combination with a chemostat culture to allow for a controlled approach to reproducibly cultivate biofilms and to investigate bacterial adhesion kinetics at constant and low shear conditions. The findings will support developing and adequate testing of biomaterials surface modifications eventually preventing biomaterial-associated infections.
Collapse
Affiliation(s)
- Claudia Lüdecke
- Leibniz Institute for Natural Product Research and Infection Biology, Hans Knöll Institute (HKI), Bio Pilot Plant, Jena, Germany
- Faculty of Physics and Astronomy, Chair of Materials Science (CMS), Friedrich Schiller University Jena, Jena, Germany
| | - Klaus D. Jandt
- Faculty of Physics and Astronomy, Chair of Materials Science (CMS), Friedrich Schiller University Jena, Jena, Germany
- * E-mail: (MR); (KDJ)
| | - Daniel Siegismund
- Otto Schott Institute of Materials Research (OSIM), Department of Metallic Materials, Friedrich Schiller University Jena, Jena, Germany
| | - Marian J. Kujau
- Leibniz Institute for Natural Product Research and Infection Biology, Hans Knöll Institute (HKI), Bio Pilot Plant, Jena, Germany
| | - Emerson Zang
- Leibniz Institute for Natural Product Research and Infection Biology, Hans Knöll Institute (HKI), Bio Pilot Plant, Jena, Germany
| | - Markus Rettenmayr
- Otto Schott Institute of Materials Research (OSIM), Department of Metallic Materials, Friedrich Schiller University Jena, Jena, Germany
| | - Jörg Bossert
- Faculty of Physics and Astronomy, Chair of Materials Science (CMS), Friedrich Schiller University Jena, Jena, Germany
| | - Martin Roth
- Leibniz Institute for Natural Product Research and Infection Biology, Hans Knöll Institute (HKI), Bio Pilot Plant, Jena, Germany
- * E-mail: (MR); (KDJ)
| |
Collapse
|
14
|
Goode KR, Asteriadou K, Robbins PT, Fryer PJ. Fouling and Cleaning Studies in the Food and Beverage Industry Classified by Cleaning Type. Compr Rev Food Sci Food Saf 2013. [DOI: 10.1111/1541-4337.12000] [Citation(s) in RCA: 90] [Impact Index Per Article: 8.2] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/30/2022]
Affiliation(s)
- Kylee R. Goode
- School of Chemical Engineering; Univ. of Birmingham; Edgbaston; Birmingham; B15 2TT; U.K
| | - Konstantia Asteriadou
- School of Chemical Engineering; Univ. of Birmingham; Edgbaston; Birmingham; B15 2TT; U.K
| | - Phillip T. Robbins
- School of Chemical Engineering; Univ. of Birmingham; Edgbaston; Birmingham; B15 2TT; U.K
| | - Peter J. Fryer
- School of Chemical Engineering; Univ. of Birmingham; Edgbaston; Birmingham; B15 2TT; U.K
| |
Collapse
|
15
|
Verghese B, Lok M, Wen J, Alessandria V, Chen Y, Kathariou S, Knabel S. comK prophage junction fragments as markers for Listeria monocytogenes genotypes unique to individual meat and poultry processing plants and a model for rapid niche-specific adaptation, biofilm formation, and persistence. Appl Environ Microbiol 2011; 77:3279-92. [PMID: 21441318 PMCID: PMC3126449 DOI: 10.1128/aem.00546-11] [Citation(s) in RCA: 90] [Impact Index Per Article: 6.9] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/09/2011] [Accepted: 03/14/2011] [Indexed: 12/21/2022] Open
Abstract
Different strains of Listeria monocytogenes are well known to persist in individual food processing plants and to contaminate foods for many years; however, the specific genotypic and phenotypic mechanisms responsible for persistence of these unique strains remain largely unknown. Based on sequences in comK prophage junction fragments, different strains of epidemic clones (ECs), which included ECII, ECIII, and ECV, were identified and shown to be specific to individual meat and poultry processing plants. The comK prophage-containing strains showed significantly higher cell densities after incubation at 30°C for 48 h on meat and poultry food-conditioning films than did strains lacking the comK prophage (P < 0.05). Overall, the type of strain, the type of conditioning film, and the interaction between the two were all highly significant (P < 0.001). Recombination analysis indicated that the comK prophage junction fragments in these strains had evolved due to extensive recombination. Based on the results of the present study, we propose a novel model in which the concept of defective comK prophage was replaced with the rapid adaptation island (RAI). Genes within the RAI were recharacterized as "adaptons," as these genes may allow L. monocytogenes to rapidly adapt to different food processing facilities and foods. If confirmed, the model presented would help explain Listeria's rapid niche adaptation, biofilm formation, persistence, and subsequent transmission to foods. Also, comK prophage junction fragment sequences may permit accurate tracking of persistent strains back to and within individual food processing operations and thus allow the design of more effective intervention strategies to reduce contamination and enhance food safety.
Collapse
Affiliation(s)
- Bindhu Verghese
- Department of Food Science, The Pennsylvania State University, University Park, PA 16802, USA.
| | | | | | | | | | | | | |
Collapse
|