A microbial fuel cell capable of converting gaseous toluene to electricity

Airborne Toluene Detection Using Metal-Organic Frameworks

The pollution of indoor air is a major worldwide concern in our modern society for people's comfort, health, and safety. In particular, toluene, present in many substances including paints, thinners, candles, leathers, cosmetics, inks, and glues, affects the human health even at very low concentrations throughout its action on the central nervous system. Its prevalence in many workplace environments can fluctuate considerably, which led to firm regulation with exposure limits varying between 50 and 400 ppm depending on exposure time. This therefore requires the development of technologies for an accurate detection of this contaminant. Metal-organic frameworks have been proposed as promising candidates to detect and monitor a series of molecules at even extremely low concentrations owing to the high tunability of their functionality. Herein, a high-throughput Monte Carlo screening approach was devised to identify the best MOFs from the computation-ready, experimental (CoRE) metal-organic framework (MOF) density-derived electrostatic and chemical (DDEC) database for the selective capture of toluene from air at room temperature, with the consideration of a ternary mixture composed of extremely low-level concentration of toluene (10 ppm) in oxygen and nitrogen to mimic the composition of air. An aluminum MOF, DUT-4, with channel-like micropores was identified as an excellent candidate for the selective adsorption of toluene from air with a predicted adsorption uptake of 0.5 g/g at 10 ppm concentration and room temperature. The toluene adsorption behavior of DUT-4 at low equivalent concentrations, alongside its sensing performance, was further experimentally investigated by its incorporation in a quartz crystal microbalance sensor, confirming the promises of DUT-4. Decisively, the resulting high sensitivity and fast kinetics of our developed sensor highlight the applicability of this hand-in-hand computational-experimental methodology to porous material screening for sensing applications.

Performance of bioelectrochemical systems in treating exhaust gas with power generation: Effects of shock-load, shut-down episodes and microbial community

A diffusive packed anode-bioelectrochemical (Dpa-Bes) system was constructed by feeding waste gas from the cathode to the anode tank in DPa-Bes through a proton exchange membrane (PEM). The high removal of oxygen by the PEM and the effective combination of the two packing materials reduced the electron loss and enhanced the proton transfer capacity, promoting the removal of acetone from the exhaust gas and increasing the output power. The maximum acetone removal efficiency of the modified Dpa-Bes reached ∼99 % after seven days of closed-circuit operation, with a 3.2-fold increase in maximum power density and a 2.27-fold increase in closed-circuit voltage relative to those of the unmodified Dpa-Bes. When the acetone concentration was 2400 ppm, the removal efficiency was 73.22 % and the elimination capacity was at its highest value of 290.21 g/m³/h. Microbial analysis revealed that the conductive filter contained abundant facultative and anaerobic bacteria, whereas the non-conductive filter was rich in aerobic bacteria. The abundance of anaerobic and facultative microorganisms in Dpa-Bes was much higher than in the unmodified Dpa-Bes, and the dominant bacteria were Flavobacterium and Ferruginibacter.

Gaseous isopropanol removal in a microbial fuel cell with deoxidizing anode: Performance, anode characteristics and microbial community

A deoxidizing packing material (DPM) with an encapsulated deoxidizing agent (DA) was developed to construct the packed anodes of a trickle-bed microbial fuel cell (TB-MFC) for treating waste gas. The encapsulated DA can consume O₂ in waste gas and increase the voltage output and power density (PD) of the constructed TB-MFC. The DPM effectively enables the circulating water in TB-MFC for maintaining a low level of dissolved oxygen for 80 h. The results revealed that when the concentration of isopropanol (IPA) in waste gas was 0.74 g/m³, the TB-MFC (DPM with DA) exhibited an IPA removal efficiency (RE) of up to 99.7%. When DPM with DA was used as the packing material of the TB-MFC (486.6 mW/m³), the PD was 2.54 times that obtained when using coke as the packing material (191.6 mW/m³). The next-generation sequencing results demonstrated that because the oxygen content of the MFC anode chamber decreased over time in the TB-MFC, the richness of anaerobic electrogens (Pseudoxanthomonas, Flavobacterium, and Ferruginibacter) in the packing materials was increased. These electrogens mainly attached to the DPM, and IPA-degraders appeared in the circulating water of the TB-MFC. This enabled the TB-MFC to simultaneously achieve a high voltage output and IPA RE.

A vertically configured photocatalytic-microbial fuel cell for electricity generation and gaseous toluene degradation

A vertically configured photocatalytic-microbial fuel cell (photo-MFC) is developed by combining a nanodiamond-decorated ZnO (ZnO/ND) photocathode with a bioanode. The system can effectively couple the light energy with bioenergy to enhance the degradation of volatile organic compounds (VOCs) and boost electricity output. Results show that the composite system exhibits increased performance for toluene removal (60.65%), higher than those of individual parts (ZnO/ND-photocatalysis: 37.16%, MFC: 17.81%). Furthermore, its electrochemical performance is dramatically increased. The peak power density of 120 mW/m² and the current density of 1.07 A/m² are generated under light illumination, which are about 1.57-fold and 1.37-fold higher than that under dark (76 mW/m², 0.78 A/m²), respectively. Microbial community analysis demonstrates Proteobacteria and Firmicute are dominant phyla, implying they play important roles on accelerating the extracellular-electron transfer and toluene degradation. In addition, the underlying mechanism for toluene degradation in the photo-MFC system is preliminary explored. Our results suggest that the photo-MFC has great potential for simultaneous treatment of VOCs with energy recovery.

Exogenous electron transfer mediator enhancing gaseous toluene degradation in a microbial fuel cell: Performance and electron transfer mechanism

Effective electron transfer (ET) between microorganisms and electrodes is essential for the toluene degradation and power generation in a microbial fuel cell (MFC). In this work, the neutral red, with excellent electrochemical reversibility and compatible redox potential as NADH/NAD⁺, was selected as electron mediator to boost the performance of the MFC. Experimental results revealed that, with the 0.5 μM neutral red, the removal efficiency and coulombic efficiency of the gaseous toluene powered MFC was increased by ~19% and ~400%, respectively. However, further increase in neutral red concentration resulted in a decreased in removal efficiency and coulombic efficiency, which was attributed by the toxicity of neutral red to the microbes. The microbial community analysis indicated that, with the dosage of the neutral red, the dominated bacteria shifted from Geobacter to Ignavibacteriales, resulting in a high coulombic efficiency. With the further increase in the neutral red, the amount of Ignavibacteriales gradually decreased and thus the coulombic efficiency declined at a high neutral red concentration. Based on the cyclic voltammetry analysis, an electron transport pathway involving neutral red, cytochromes, and OMCs in neutral red mediated MFC was proposed. Overall, the dosage of neutral not only enhanced the electron transfer but also induced the growth of the exoelectrogens, and thus significantly improve the MFC performance.

Bioelectricity production and xylene biodegradation through double chamber benthic microbial fuel cells fed with sugarcane waste as a substrate

Xylene, a recalcitrant compound present in wastewater from activities of petrochemical and chemical industries causes chronic problems for living organisms and the environment. Xylene contaminated wastewater may be biodegraded through a benthic microbial fuel cell (BMFC) as seen in this study. Xylene was oxidized into intermediate 3-methyl benzoic acid and entirely converted into non-toxic carbon dioxide. The highest voltage of the BMFC reactor was generated at 410 mV between 23 and 90 days when cell potential was 1 kΩ. The reactor achieved a maximum power density of about 63 mW/m², and a current of 0.4 mA which was optimized from variable resistance (20 Ω - 1 kΩ). However, the maximum biodegradation efficiency of the BMFC was at 87.8%. The cyclic voltammetry curve helped to determine that the specific capacitance was 0.124 F/g after 30 days of the BMFC operation. Furthermore, the fitting equivalent circuit was observed with the help of Nyquist plot for calculating overall internal resistance of 65.82 Ω on 30th day and 124.5 Ω on 80th day. Staphylococcus edaphicus and Staphylococcus sparophiticus were identified by 16S rRNA sequencing as the dominant species in the control and BMFC electrode, presumably associated with xylene biodegradation.

Improving the performance of biotrickling filter microbial fuel cells in treating exhaust gas by adjusting the oxygen content of the anode tank

A biotrickling filter (BTF) was combined with a microbial fuel cell (MFC) to remove ethyl acetate from exhaust gas while generating electricity in the process. The results indicated that the use of carbide porous ceramic rings (CPCR) as auxiliary anodes produced more biomass and exhibited a high average removal efficiency (98%), making it a superior microorganism growth carrier compared with carbon coke. When CPCR was used as the cathode in the BTF-MFC, the maximum power density (PD) was 5.64-14.8% of that achieved when carbon cloth was used as the cathode, revealing that CPCR is not a suitable cathode. The maximum elimination capacity (EC) and output voltage of the two-stage BTF-MFC (tBTF-MFC) were only 69.4% and 68.4% of those of the single-stage BTF-MFC (sBTF-MFC), presumably because of voltage reversal. Although the output voltage and EC in the tBTF-MFC were less than those in the sBTF-MFC, the follow-up field application involves stacking multiple small MFCs to remove high-concentration pollutants and generate a high power output. Additionally, continuously adding sodium sulfite decreased the average dissolved oxygen; generated an averaged closed-circuit voltage of 477 mV; and produced a maximum PD of 71.7 mW/m³. These findings demonstrated that the aforementioned method can effectively improve the problem of oxygen and MFC anodes competing for electrons, thus delivering a method that enhances MFC performance through controlling the amount of oxygen in practical applications.

Resorcinol as a highly efficient aromatic electron donor in bioelectrochemical system

Bioelectrochemical systems (BESs) have been known as a promising technology for accelerating aromatic contaminants degradation and energy recovery. However, most existing studies concentrate on aromatics metabolized through a benzoyl-CoA pathway while those metabolized through other pathways are limited. In this work, resorcinol, a typical aromatic contaminant as well as a key central intermediate (other than benzoyl-CoA) involved in aromatics anaerobic biodegradation, was studied in BESs. Unlike the general impression of the relatively poor organic-to-current performance in the aromatics driven BESs, high efficiencies for resorcinol-fed BESs were observed with a current density and coulombic efficiency of up to 0.26 ± 0.05 mAcm^-2 and 74.3 ± 10.7%, respectively. The higher performance likely correlates to the readily fermentable property of resorcinol. Analysis of microbial communities in the biofilm suggests a syntrophic interaction between resorcinol-degrading bacteria (RDB) and anode-respiring bacteria (ARB) was involved in current generation. Additional tests involving the removal of accumulated acetate through fast resorcinol feeding indicates that a mechanism based on direct utilization of resorcinol for current generation may also exist. This study extends the knowledge for the fate of aromatics in BESs and indicates that aromatics entering into the resorcinol metabolic pathway can be treated efficiently with good energy recovery efficiency in BESs.

Advancement in Benthic Microbial Fuel Cells toward Sustainable Bioremediation and Renewable Energy Production

Anthropogenic activities are largely responsible for the vast amounts of pollutants such as polycyclic aromatic hydrocarbons, cyanides, phenols, metal derivatives, sulphides, and other chemicals in wastewater. The excess benzene, toluene and xylene (BTX) can cause severe toxicity to living organisms in wastewater. A novel approach to mitigate this problem is the benthic microbial fuel cell (BMFC) setup to produce renewable energy and bio-remediate wastewater aromatic hydrocarbons. Several mechanisms of electrogens have been utilized for the bioremediation of BTX through BMFCs. In the future, BMFCs may be significant for chemical and petrochemical industry wastewater treatment. The distinct factors are considered to evaluate the performance of BMFCs, such as pollutant removal efficiency, power density, and current density, which are discussed by using operating parameters such as, pH, temperature and internal resistance. To further upgrade the BMFC technology, this review summarizes prototype electrode materials, the bioremediation of BTX, and their applications.

A novel UV-assisted PEC-MFC system with CeO2/TiO2/ACF catalytic cathode for gas phase VOCs treatment

Emissions of volatile organic compounds (VOCs) air pollutants could worsen air quality and adversely affect human health, thus developing more efficient low-temperature VOCs removal techniques is desired. A novel continuous system integrating UV-assisted photo-electrochemical catalysis with microbial fuel cell (UV-assisted PEC-MFC) has been established for promoting removal of gaseous ethyl acetate or toluene and generating electricity simultaneously. In this system, CeO₂/TiO₂/ACF catalytic cathode is prepared and used for combination with bio-anode for accelerating cathodic reaction. This UV-assisted PEC-MFC system exhibits an excellent elimination capacity (EC) of ethyl acetate (∼0.39 g/m³, EC: ∼2.52 g/m³/h) or toluene (∼0.29 g/m³, EC: 1.89 g/m³/h) under close-circuit condition. Furthermore, an outstanding elimination capacity (EC: 28.04 g/m³/h) for high concentration toluene (∼4.10 g/m³) removal is obtained after toluene gas passes sequentially through the catalytic cathode then the bio-anode. This way of PEC degradation and biodegradation, avoids inhibition of exoelectrogens activity from toxicity of high concentration toluene. Simultaneously, the cell voltage of UV-assisted PEC-MFC system is stable at 0.11 V (vs. SCE) and 1.452×10^-4 kWh is generated from treatment of toluene gas stream in 6 h duration time. The possible mechanism of VOCs removal in this novel system has been proposed and discussed. This study provides new technical basis for treating gaseous pollutants via integrating photo-electrochemical catalysis with electricity generating microbial fuel cell for energy conversion.

Enhancement of gaseous o-xylene degradation in a microbial fuel cell by adding Shewanella oneidensis MR-1

An exoelectrogens, Shewanella oneidensis MR-1 (S. oneidensis MR-1), was supplied to a microbial fuel cell (MFC) to enhance the degradation of a recalcitrant organic compound, o-xylene. The experimental results revealed that, with the addition of the S. oneidensis MR-1, the o-xylene removal efficiency increased by 35-76% compared with the original MFC. The presence of the S. oneidensis MR-1 not only improved the activity of the biofilm in the bioanode but also developed the connections between the bacteria by nanowires. Therefore, the maximum power density increased from 52.1 to 92.5 mW/m³ after the addition of the S. oneidensis MR-1. The microbial community analysis showed that adding the S. oneidensis MR-1 increased the biodiversity in bioanode. The dominant exoelectrogens shifted from Zoogloea sp., Delftia sp., Achromobacter sp., Acinetobacter sp., Chryseobacterium sp., and Stenotrophomonas sp. to Zoogloea sp., Delftia sp., Shewanella sp., Achromobacter sp., Hydrogenophaga sp., Sedimentibacter sp. and Chryseobacterium sp.. Furthermore, the cyclic voltammetry analysis showed that the outer membrane bound protein complex of OmcA-MtrCAB was involved as direct electron transfer pathway in the S. oneidensis MR-1 containing bioanode. We believed that this work is promising to provide optional strategy for efficient VOCs degradation by adjusting the microbial community in the bioanode.

Potential applications of graphene-based nanomaterials as adsorbent for removal of volatile organic compounds

In recent years, graphene-based materials (GBMs) have been regarded as the core technology in diverse research fields. Consequently, the demand for large-scale synthesis of GBMs has been increasing continuously for various fields of industry. These materials have become a competitive adsorbent for the removal of environmental pollutants with improved adsorption capacity and cost effectiveness through hybridization or fabrication of various functionalities on their large surface. In particular, their applicability opens up new avenues for the adsorptive removal of volatile organic compounds (VOCs) (e.g., through the build-up of efficient air purification systems). This review explored the basic knowledge and synthesis approaches for GBMs and their performances as adsorbent for VOC removal. Moreover, the mechanisms associated with the VOC removal were explained in detail. The performance of GBMs has also been evaluated along with their present limitations and future perspectives.

Performance of trickling bed microbial fuel cell treating isopropyl alcohol vapor: Effects of shock-load and shut-down episodes

This work investigates the enhancement in the removal efficiency of isopropyl alcohol (IPA) vapor by a hollow trickling-bed microbial fuel cell (TB-MFC) that can be achieved by certain modifications. The effects of shock load and shutdown on the performance of TB-MFC were evaluated. When organic loading (OL) of IPA was approximately 22.1-88.5 g m^-3 h^-1, the removal efficiency of 85.1-93.8% of the TB-MFC was achieved. With an empty bed residence time (EBRT) of 60 s and an inlet IPA concentration of 4.42 g m^-3, the TB-MFC achieved its maximum EC of 150 g m^-3 h^-1, which was 1.7-4 times higher than reported for conventional biofiltration technology. A maximum closed-circuit voltage (CCV) of 173 mV and maximum power density (PD_max) of 53.2 mW m^-3 were obtained under optimal conditions (IPA concentration = 0.73 g m^-3; EBRT = 60 s). Short-term shutdown (seven days) did not cause significant changes in EC, CCV, and PD_max of the TB-MFC. This investigation establishes the feasibility of using a trickling-bed MFC to substantially increase the removal of IPA and handle shock-load and shut-down events. To increase EC and power output, this laboratory-scale TB-MFC could easily be scaled up by stacking anodes, and has great potential for future application in the field in various industries.

Adsorption of toluene with water on zeolitic imidazolate framework-8/graphene oxide hybrid nanocomposites in a humid atmosphere

Water vapor often present in the atmosphere will influence the adsorption of volatile organic compounds (VOCs). The competitive adsorption behavior of toluene and water vapor on synthesized zeolitic imidazolate framework-8 (ZIF-8) and graphene oxide (GO) hybrid composites was investigated in a humid atmosphere. The ZIF-8/GO composites were successfully prepared in a methanol system at room temperature and exhibited tunable nanoscale morphology and surface area, both determined by the GO content. A series of characterization techniques confirmed the formation of strong interactions between ZIF-8 and GO in the synthesized composites. Adsorption experiments demonstrated that the ZIF-8/GO composites with a GO content of 4 wt% had the highest toluene adsorption capacity of 116 mg g⁻¹ at a relative humidity (RH) of 55%, increased by 19% compared with pristine ZIF-8, and the recyclability of the adsorbent was investigated. The results showed that the synthesized ZIF-8/GO composites exhibited a higher toluene uptake capacity than pristine ZIF-8 crystals even at relatively high humidity, indicating that the ZIF-8/GO composites could be effective adsorbents in a humid atmosphere.

ZIF-8/GO composites can be used as efficient and recyclable adsorbents for the removal of toluene with water in a humid atmosphere.