Removal of binary Cr(VI) and Cd(II) from the catholyte of MFCs and determining their fate in EAB using fluorescence probes

High efficiency electrochemical separation of uranium(VI) from uranium-containing wastewater by microbial fuel cells with different cathodes

As an emerging versatile technology for separating uranium from uranium-containing wastewater (UCW), microbial fuel cell (MFC) offers a novel approach to UCW treatment. Its cathode is essential for the treatment of UCW. To thoroughly investigate the efficacy of MFC in treating UCW, investigations were conducted using MFCs with five materials (containing iron sheet (IP), stainless steel mesh (SSM), carbon cloth (CC), carbon brush (CB), and nickel foam (NF)) as cathodes. The results revealed that each MFC system performed differently in terms of carbon source degradation, uranium removal, and electricity production. In terms of carbon source degradation, CB-MFC showed the best performance. The best uranium removal method was NF-MFC, and the best electricity production method was carbon-based cathode MFC. Five MFC systems demonstrated stable performance and consistent difference over five cycles, with CC-MFC outperforming the others. Furthermore, SEM and XPS characterization of the cathode materials before and after the experiment revealed that a significant amount of U(IV) was generated during the uranium removal process, indicating that uranium ions were primarily removed by electrochemical reduction precipitation. This study confirmed that abiotic cathode MFC had a high UCW removal potential and served as a good guideline for obtaining the best cathode for MFC.

Electroactive microorganism-assisted remediation of groundwater contamination: Advances and challenges

Groundwater contamination has become increasingly prominent, therefore, the development of efficient remediation technology is crucial for improving groundwater quality. Bioremediation is cost-effective and environmentally friendly, while coexisting pollutant stress can affect microbial processes, and the heterogeneous character of groundwater medium can induce bioavailability limitations and electron donor/acceptor imbalances. Electroactive microorganisms (EAMs) are advantageous in contaminated groundwater because of their unique bidirectional electron transfer mechanism, which allows them to use solid electrodes as electron donors/acceptors. However, the relatively low-conductivity groundwater environment is unfavorable for electron transfer, which becomes a bottleneck problem that limits the remediation efficiency of EAMs. Therefore, this study reviews the recent advances and challenges of EAMs applied in the groundwater environment with complex coexisting ions, heterogeneity, and low conductivity and proposes corresponding future directions.

Bioelectrochemical systems-based metal removal and recovery from wastewater and polluted soil: Key factors, development, and perspective

Bioelectrochemical systems (BES) are considered efficient and sustainable technologies for bioenergy generation and simultaneously removal/recovery metal (loid)s from soil and wastewater. However, several current challenges of BES-based metal removal and recovery, especially concentrating target metals from complex contaminated wastewater or soil and their economic feasibility of engineering applications. This review summarized the applications of BES-based metal removal and recovery systems from wastewater and contaminated soil and evaluated their performances on electricity generation and metal removal/recovery efficiency. In addition, an in depth review of several key parameters (BES configurations, electrodes, catalysts, metal concentration, pH value, substrate categories, etc.) of BES-based metal removal and recovery was carried out to facilitate a deep understanding of their development and to suggest strategies for scaling up their specific application fields. Finally, the future intervention on multifunctional BES to improve their performances of mental removal and recovery were revealed.

Bioelectrochemical systems-based metal recovery: Resource, conservation and recycling of metallic industrial effluents

Metals represent a large proportion of industrial effluents, which due to their high hazardous nature and toxicity are responsible to create environmental pollution that can pose significant threat to the global flora and fauna. Strict ecological rules compromise sustainable recovery of metals from industrial effluents by replacing unsustainable and energy-consuming physical and chemical techniques. Innovative technologies based on the bioelectrochemical systems (BES) are a rapidly developing research field with proven encouraging outcomes for many industrial commodities, considering the worthy options for recovering metals from industrial effluents. BES technology platform has redox capabilities with small energy-intensive processes. The positive stigma of BES in metals recovery is addressed in this review by demonstrating the significance of BES over the current physical and chemical techniques. The mechanisms of action of BES towards metal recovery have been postulated with the schematic representation. Operational limitations in BES-based metal recovery such as biocathode and metal toxicity are deeply discussed based on the available literature results. Eventually, a progressive inspection towards a BES-based metal recovery platform with possibilities of integration with other modern technologies is foreseen to meet the real-time challenges of viable industrial commercialization.

Influence of Cr (VI) concentration on Cr (VI) reduction and electricity production in microbial fuel cell

Microbial fuel cell is an efficient technology to reduce pollutants of the heavy metal ions. Herein, a dual-chamber microbial fuel cell (MFC) coupled with abio-cathode and electrochemically active bacteria is fabricated to treat Cr (VI) containing wastewater and harvest bioelectricity simultaneously. To investigate the wide application of MFC for various industries, four different concentrations of Cr (VI) (6 mg/L, 15 mg/L, 40 mg/L, 100 mg/L) are used to explore the removal efficiency of Cr (VI) and the corresponding power performance. We find that the power performance gradually increases with the increment of the initial Cr (VI) concentration. Significantly, a maximum power density of 35.3 mW/m² can be achieved with the initial concentration of 100mg/L Cr (VI), while MFC only generate negligible power density (2.6 mW/m²) without the presence of Cr (VI). Meanwhile, MFC combined with the initial Cr (VI) concentration of 15 mg/L shows the highest Cr (VI) removal of 66.5%. Moreover, partial precipitates are found on the cathode surface and X-ray photoelectron spectroscopy (XPS) analysis has demonstrated that the Cr (VI) is successfully reduced into Cr (III). This study offers an alternative technology to remove Cr (VI) and synchronous electricity generation.

Tuning of Electrode Surface for Enhanced Bacterial Adhesion and Reactions: A Review on Recent Approaches

The study of bacterial adhesion and its consequences has great significance in different fields such as marine science, renewable energy sectors, soil and plant ecology, food industry, and the biomedical field. Generally, the adverse effects of microbial surface interactions have attained wide visibility. However, herein, we present distinct approaches to highlight the beneficial aspects of microbial surface interactions for various applications rather than deal with the conventional negative aspects or prevention strategies. The surface microbial reactions can be tuned for useful biochemical or bio-electrochemical applications, which are otherwise unattainable through conventional routes. In this context, the present review is a comprehensive approach to highlight the basic principles and signature parameters that are responsible for the useful microbial-electrode interactions. It also proposes various surface tuning strategies, which are useful for tuning the electrode characteristics particularly suitable for the enhanced bacterial adhesion and reactions. The tuning of surface characteristics of electrodes is discussed with a special reference to the Microbial Fuel Cell as an example.

Metal removal and recovery using bioelectrochemical technology: The major determinants and opportunities for synchronic wastewater treatment and energy production

Microbial fuel cell (MFC) technology has emerged as a new and attractive bioelectrochemical approach in the last one and a half decade that offers an alternative to conventional treatment methods to remove and recover heavy metals and organics from wastewaters with simultaneous energy production. This technique has advantage over the conventional wastewater treatment techniques, which are energy intensive, sludge producing and with little effectivity at high concentrations. Significant work has been done in the recent years on MFC principle, electrode configuration, biofilm composition, application of MFC in wastewater treatment, metal removal or recovery and energy production. Basically, metal in the cathode chamber acts as acceptor of the electrons released from the oxidation of organic matter in the anode chamber by electrogenic microbes. Literature shows that efficacy of MFCs in removal and recovery of metals and power production is significantly influenced by redox potential of the metal, initial concentration, mix metal systems, carbon source in substrate, pH, biocathode, biofilm composition, gaseous environment in cathode, electrode modification and external resistance, which have been critically reviewed for the first time in the present paper to understand the role of the determinant factors that may be explored for improvement of the MFC performance. The paper provides further insights into the techno-economic aspects of MFC technology and suggests research needs for enhanced performance and reduced costs to increase its feasibility for application at commercial level.

Outlook on the Role of Microbial Fuel Cells in Remediation of Environmental Pollutants with Electricity Generation

A wide variety of pollutants are discharged into water bodies like lakes, rivers, canal, etc. due to the growing world population, industrial development, depletion of water resources, improper disposal of agricultural and native wastes. Water pollution is becoming a severe problem for the whole world from small villages to big cities. The toxic metals and organic dyes pollutants are considered as significant contaminants that cause severe hazards to human beings and aquatic life. The microbial fuel cell (MFC) is the most promising, eco-friendly, and emerging technique. In this technique, microorganisms play an important role in bioremediation of water pollutants simultaneously generating an electric current. In this review, a new approach based on microbial fuel cells for bioremediation of organic dyes and toxic metals has been summarized. This technique offers an alternative with great potential in the field of wastewater treatment. Finally, their applications are discussed to explore the research gaps for future research direction. From a literature survey of more than 170 recent papers, it is evident that MFCs have demonstrated outstanding removal capabilities for various pollutants.

Electricity production of microbial fuel cells by degrading cellulose coupling with Cr(VI) removal

A facultative exoelectrogen strain Lsc-8 belonging to the Cellulomonas genus with the ability to degrade carboxymethyl cellulose (CMC) coupled with the reduction of Cr(VI), was successfully isolated from rumen content. The maximum output power density of the microbial fuel cells (MFCs) inoculated strain Lsc-8 was 9.56 ± 0.37 mW·m^-2 with CMC as the sole carbon source. From the biomass analysis it can be seen that the electricity generation of the MFCs was primarily attributed to the planktonic cells of strain Lsc-8 rather than the biofilm attached on the electrode, which was different from Geobacter sulfurreducens. Especially, during electricity generation of the MFCs using CMC as carbon source in the anode chamber, the Cr(VI) reduction were simultaneously realized. And it is also found that the Cr(VI) reduction ratio by strain Lsc-8 is directly related to the initial Cr(VI) concentration, and it increased with the increase of initial Cr(VI) concentration at first, then started to decrease when the Cr(VI) concentration was above 21 mg ·L^-1. Meanwhile, the highest output power density of 3.47 ± 0.28 mW·m^-2 was observed coupling with 95.22 ± 2.72 % of Cr(VI) reduction. These data suggested that the strain Lsc-8 could reduce high toxicity Cr(VI) to low toxicity Cr(III) coupled with electricity generation in MFCs with CMC as the carbon source. Our results also suggested that this study will provide a possibility to simultaneously degrade Cr(VI) and generate electricity by using cellulose as the carbon source via MFCs.

Understanding the interdependence of strain of electrotroph, cathode potential and initial Cu(II) concentration for simultaneous Cu(II) removal and acetate production in microbial electrosynthesis systems

Metallurgical microbial electrosynthesis systems (MES) are holding great promise for simultaneous heavy metal removal and acetate production from heavy metal-contaminated and organics-barren waters. How critical parameters of strain of electrotroph, cathode potential and initial heavy metal concentration affect MES performance, however, is not yet fully understood. Heavy metal of Cu(II) and four Cu(II)-tolerant electrotrophs (Stenotrophomonas maltophilia JY1, Citrobacter sp. JY3, Pseudomonas aeruginosa JY5 and Stenotrophomonas sp. JY6) were employed to evaluate MES performance at various cathode potentials (-900 or -600 mV vs. standard hydrogen electrode) and initial Cu(II) concentrations (60-120 mg L^-1). Each electrotrophs exhibited incremental Cu(II) removals with increased Cu(II) at -900 mV, higher than at -600 mV or in the abiotic controls. Acetate production by JY1 and JY6 decreased with the increase in initial Cu(II), compared to an initial increase and a decrease thereafter for JY3 and JY5. For each electrotrophs, the biofilms than the planktonic cells released more amounts of extracellular polymeric substances (EPS) with a compositional diversity and stronger Cu(II) complexation at -900 mV. These were higher than at -600 mV, or in the controls either under open circuit conditions or in the absence of Cu(II). This work demonstrates the interdependence of strain of electrotroph, cathode potential and initial Cu(II) on simultaneous Cu(II) removal and acetate production through the release of different amounts of EPS with diverse composites, contributing to enhancing the controlled MES for efficient recovery of value-added products from Cu(II)-contaminated and organics-barren waters.

Progress Towards Bioelectrochemical Remediation of Hexavalent Chromium

Chromium is one of the most frequently used metal contaminants. Its hexavalent form Cr(VI), which is exploited in many industrial activities, is highly toxic, is water-soluble in the full pH range, and is a major threat to groundwater resources. Alongside traditional approaches to Cr(VI) treatment based on physical-chemical methods, technologies exploiting the ability of several microorganisms to reduce toxic and mobile Cr(VI) to the less toxic and stable Cr(III) form have been developed to improve the cost-effectiveness and sustainability of remediating hexavalent chromium-contaminated groundwater. Bioelectrochemical systems (BESs), principally investigated for wastewater treatment, may represent an innovative option for groundwater remediation. By using electrodes as virtually inexhaustible electron donors and acceptors to promote microbial oxidation-reduction reactions, in in situ remediation, BESs may offer the advantage of limited energy and chemicals requirements in comparison to other bioremediation technologies, which rely on external supplies of limiting inorganic nutrients and electron acceptors or donors to ensure proper conditions for microbial activity. Electron transfer is continuously promoted/controlled in terms of current or voltage application between the electrodes, close to which electrochemically active microorganisms are located. Therefore, this enhances the options of process real-time monitoring and control, which are often limited in in situ treatment schemes. This paper reviews research with BESs for treating chromium-contaminated wastewater, by focusing on the perspectives for Cr(VI) bioelectrochemical remediation and open research issues.

Mutual benefits of acetate and mixed tungsten and molybdenum for their efficient removal in 40 L microbial electrolysis cells

Practical application of metallurgical microbial electrolysis cells (MECs) requires efficient removal of metals and organics in larger reactors. A 40 L cylindrical single-chamber MEC fed acetate was used to achieve high removals of W(VI) and Mo(VI). In the presence of both metals, there were nearly complete removals of W (97 ‒ 98%), Mo (98 ‒ 99%), and acetate (95 ‒ 96%), along with a low level of hydrogen production (0.0037-0.0039 L/L/d) at a hydraulic residence time (HRT) of 2 d (influent ratios of W:Mo:acetate of 0.5:1.0:24 mM). The final concentrations of these conditions were sufficient to meet national wastewater discharge standards. In the controls with individual metals or acetate, lower contaminant removals were obtained (W, 2 ‒ 4%; Mo, 3 ‒ 5%, acetate, 36 ‒ 39%). Metals removal in all cases was primarily due to the biocathodes rather than the bioanodes. The presence of metals decreased microbial diversity on the anodes and increased diversity on the cathodes, based on analysis at the phylum, class and genus levels, as a function of HRT and influent concentration. This study demonstrated the feasibility of larger-scale single-chamber MECs for efficient treatment of W and Mo, moving metallurgical MECs closer to commercialization for wastewater treatment of these two metals.

Electrosynthesis of acetate from inorganic carbon (HCO3-) with simultaneous hydrogen production and Cd(II) removal in multifunctional microbial electrosynthesis systems (MES)

The simultaneous production of acetate from bicarbonate (from CO₂ sequestration) and hydrogen gas, with concomitant removal of Cd(II) heavy metal in water is demonstrated in multifunctional metallurgical microbial electrosynthesis systems (MES) incorporating Cd(II) tolerant electrochemically active bacteria (EAB) (Ochrobactrum sp. X1, Pseudomonas sp. X3, Pseudomonas delhiensis X5, and Ochrobactrum anthropi X7). Strain X5 favored the production of acetate, while X7 preferred the production of hydrogen. The rate of Cd(II) removal by all EAB (1.20-1.32 mg/L/h), and the rates of acetate production by X5 (29.4 mg/L/d) and hydrogen evolution by X7 (0.0187 m³/m³/d) increased in the presence of a circuital current. The production of acetate and hydrogen was regulated by the release of extracellular polymeric substances (EPS), which also exhibited invariable catalytic activity toward the reduction of Cd(II) to Cd(0). The intracellular activities of glutathione (GSH), catalase (CAT), superoxide dismutase (SOD) and dehydrogenase were altered by the circuital current and Cd(II) concentration, and these regulated the products distribution. Such understanding enables the targeted manipulation of the MES operational conditions that favor the production of acetate from CO₂ sequestration with simultaneous hydrogen production and removal/recovery of Cd(II) from metal-contaminated and organics-barren waters.

Reduction of Cu(II) and simultaneous production of acetate from inorganic carbon by Serratia Marcescens biofilms and plankton cells in microbial electrosynthesis systems

Simultaneous Cu(II) reduction (6.42 ± 0.02 mg/L/h), acetate production (1.13 ± 0.02 mg/L/h) from inorganic carbon (i.e., CO₂ sequestration), and hydrogen evolution (0.0315 ± 0.0005 m³/m³/d) were achieved in a Serratia marcescens Q1 catalyzed microbial electrosynthesis system (MES). The biofilms released increasing amounts of extracellular polymeric substances (EPS) with a higher compositional diversity and stronger Cu(II) complexation, compared to the plankton cells, at higher Cu(II) concentrations (up to 80 mg/L) and circuital currents (cathodic potential of -900 mV vs. standard hydrogen electrode (SHE)). Moreover, the biofilms reduced Cu(II) to Cu(0) more effectively than the plankton cells. At Cu(II) concentrations below 80 mg/L, the dehydrogenase activity in the biofilms was higher than in the plankton cells, and increased with circuital current, which was converse to the lower activities of catalase (CAT), superoxide dismutase (SOD) and antioxidative glutathione (GSH) in the biofilms than the plankton cells, although all these physiological activities were positively correlated with the concentration of Cu(II). This is the first study that evaluates the EPS constituents and the physiological activities of the biofilms and the plankton cells in the MESs, that favors the production of acetate from CO₂ sequestration and the simultaneous reduction of Cu(II) from organics-barren waters contaminated with heavy metals.

A loop of catholyte effluent feeding to bioanodes for complete recovery of Sn, Fe, and Cu with simultaneous treatment of the co-present organics in microbial fuel cells

A loop of catholyte effluent feeding to the bioanodes of air-cathode microbial fuel cells (MFCs) achieved complete recovery of mixed Sn(II), Fe(II) and Cu(II), with simultaneous treatment of the co-present organics in synthetic wastewater of printed circuit boards (PrCBs). This in-situ utilization of caustic in the cathodes and the neutralization of acid in the anodes achieved superior metal recovery performance at an optimal hydraulic retention time (HRT) of 24 h. Cathode chambers primarily removed Sn of 91 ± 4% (bottom: 74 ± 3%; electrode: 17 ± 1%), Fe of 89 ± 8% (bottom: 64 ± 4%; electrode: 25 ± 2%), and Cu of 92 ± 7% (electrode: 63 ± 5%; bottom: 29 ± 1%), compared to Sn of 9 ± 3% (electrode: 7 ± 1%; bottom: 2 ± 1%), Fe of 9 ± 3% (electrode: 8 ± 3%; bottom: 1 ± 0%), and Cu of 7 ± 3% (electrode: 4 ± 1%; bottom: 3 ± 1%) in the bioanodes. Bacterial communities on the anodes were well evolutionarily developed after the feeding of catholyte effluent, with the increase in abundance of Rhodopseudomonas and Geobacter, and the shift from Thiobacillus and Acinetobacter to Pseudomonas, Comamonas, Aeromonas and Azospira. This loop of cathodic effluent feeding to the bioanodes of MFCs may represent a unique method for complete metal recovery with simultaneous extraction of renewable electrical energy from the co-present organics. This study also offers new insights into the development of compact microbial electro-metallurgical processes for simultaneous recovery of value-added products from PrCBs processing wastewaters and accomplishing the national wastewater discharge standard for both metals and organics.