Anterior spinal column augmentation with injectable bone cements

Thoracic spinal cord injury and paraplegia caused by intradural cement leakage after percutaneous kyphoplasty: A case report

BACKGROUND

Percutaneous kyphoplasty (PKP) is a pivotal intervention for osteoporotic fractures, pathological vertebral compression fractures, and vertebral bone tumors. Despite its efficacy, the procedure presents challenges, notably complications arising from intradural cement leakage. Timely and accurate diagnosis, coupled with emergent intervention is imperative to improve patient prognosis. This case report illuminates the intricacies and potential complications associated with PKP, emphasizing the critical need for vigilant monitoring, prompt diagnosis, and immediate intervention to mitigate adverse outcomes.

CASE SUMMARY

A 58-year-old male patient, experiencing a T7 osteoporosis-related pathological compression fracture, underwent PKP at a local hospital. Two weeks post-procedure, the patient developed paraplegic and dysuric symptoms, necessitating emergency decompression surgery. Gradual improvement was achieved, marked by the restoration of muscle strength, sensation, and mobility.

CONCLUSION

PKP Intradural cement leakage following PKP is unusual and potentially fatal. Prompt imaging examinations, urgent evaluation, and the decompression surgery are essential, which help alleviate symptoms associated with spinal damage, markedly improving the overall prognosis.

Biological and mechanical performance and degradation characteristics of calcium phosphate cements in large animals and humans

Calcium phosphate cements (CPCs) have been used to treat bone defects and support bone regeneration because of their good biocompatibility and osteointegrative behavior. Since their introduction in the 1980s, remarkable clinical success has been achieved with these biomaterials, because they offer the unique feature of being moldable and even injectable into implant sites, where they harden through a low-temperature setting reaction. However, despite decades of research efforts, two major limitations concerning their biological and mechanical performance hamper a broader clinical use. Firstly, achieving a degradation rate that is well adjusted to the dynamics of bone formation remains a challenging issue. While apatite-forming CPCs frequently remain for years at the implant site without major signs of degradation, brushite-forming CPCs are considered to degrade to a greater extent. However, the latter tend to convert into lower soluble phases under physiological conditions, which makes their degradation behavior rather unpredictable. Secondly, CPCs exhibit insufficient mechanical properties for load bearing applications because of their inherent brittleness. This review places an emphasis on these limitations and provides an overview of studies that have investigated the biological and biomechanical performance as well as the degradation characteristics of different CPCs after implantation into trabecular bone. We reviewed studies performed in large animals, because they mimic human bone physiology more closely in terms of bone metabolism and mechanical loading conditions compared with small laboratory animals. We compared the results of these studies with clinical trials that have dealt with the degradation behavior of CPCs after vertebroplasty and kyphoplasty.

Biocompatibility of calcium phosphate bone cement with optimised mechanical properties: an in vivo study

This work establishes the in vivo performance of modified calcium phosphate bone cements for vertebroplasty of spinal fractures using a lapine model. A non-modified calcium phosphate bone cement and collagen-calcium phosphate bone cements composites with enhanced mechanical properties, utilising either bovine collagen or collagen from a marine sponge, were compared to a commercial poly(methyl methacrylate) cement. Conical cement samples (8 mm height × 4 mm base diameter) were press-fit into distal femoral condyle defects in New Zealand White rabbits and assessed after 5 and 10 weeks. Bone apposition and tartrate-resistant acid phosphatase activity around cements were assessed. All implants were well tolerated, but bone apposition was higher on calcium phosphate bone cements than on poly(methyl methacrylate) cement. Incorporation of collagen showed no evidence of inflammatory or immune reactions. Presence of positive tartrate-resistant acid phosphatase staining within cracks formed in calcium phosphate bone cements suggested active osteoclasts were present within the implants and were actively remodelling within the cements. Bone growth was also observed within these cracks. These findings confirm the biological advantages of calcium phosphate bone cements over poly(methyl methacrylate) and, coupled with previous work on enhancement of mechanical properties through collagen incorporation, suggest collagen-calcium phosphate bone cement composite may offer an alternative to calcium phosphate bone cements in applications where low setting times and higher mechanical stability are important.

Radiologic study of disc behavior following compression fracture of the thoracolumbar hinge managed by kyphoplasty: A 52-case series

INTRODUCTION

Kyphoplasty has proved effective for durable correction of traumatic vertebral deformity following Magerl A fracture, but subsequent behavior of the adjacent discs is unclear. The objective of the present study was to analyze evolution according to severity of initial kyphosis and quality of fracture reduction.

MATERIAL AND METHOD

A single-center prospective study included cases of single compression fracture of the thoracolumbar hinge managed by Kyphon Balloon Kyphoplasty with polymethylmethacrylate bone cement. Radiology focused on traumatic vertebral kyphosis (VK), disc angulation (DA) and disc height index (DHI) in the adjacent discs. Linear regression assessed the correlation between superior disc height index (SupDHI) and postoperative VK on the one hand and correction gain on the other, using the Student t test for matched pairs and Pearson correlation coefficient.

RESULTS

Fifty-two young patients were included, with mean follow-up of 18.6 months. VK fell from 13.9° preoperatively to 8.2° at last follow-up. DHI found significant superior disc subsidence (P=0.0001) and non-significant inferior disc subsidence (P=0.116). DA showed significantly reduced superior disc lordosis (P=4*10(-5)). SupDHI correlated with VK correction (r=0.32). Preoperative VK did not correlate with radiologic degeneration of the adjacent discs.

CONCLUSION

Correction of traumatic vertebral deformity avoids subsidence and loss of mechanical function in the superior adjacent disc. The underlying disc compensates for residual deformity. Balloon kyphoplasty is useful in compression fracture, providing significant reduction of traumatic vertebral deformity while conserving free and healthy adjacent discs.

LEVEL OF EVIDENCE

IV.

Variability of the pullout strength of cancellous bone screws with cement augmentation

BACKGROUND

Orthopaedic surgeons often face clinical situations where improved screw holding power in cancellous bone is needed. Injectable calcium phosphate cements are one option to enhance fixation.

METHODS

Paired screw pullout tests were undertaken in which human cadaver bone was augmented with calcium phosphate cement. A finite element model was used to investigate sensitivity to screw positional placement.

FINDINGS

Statistical analysis of the data concluded that the pullout strength was generally increased by cement augmentation in the in vitro human cadaver tests. However, when comparing the individual paired samples there were surprising results with lower strength than anticipated after augmentation, in apparent contradiction to the generally expected conclusion. Investigation using the finite element model showed that these strength reductions could be accounted for by small screw positional changes. A change of 0.5mm might result in predicted pullout force changes of up to 28%.

INTERPRETATION

Small changes in screw position might lead to significant changes in pullout strength sufficient to explain the lower than expected individual pullout values in augmented cancellous bone. Consequently whilst the addition of cement at a position of low strength would increase the pullout strength at that point, it might not reach the pullout strength of the un-augmented paired test site. However, the overall effect of cement augmentation produces a significant improvement at whatever point in the bone the screw is placed. The use of polymeric bone-substitute materials for tests may not reveal the natural variation encountered in tests using real bone structures.

Biocompatibility of calcium phosphate bone cement with optimized mechanical properties

The broad aim of this work was to investigate and optimize the properties of calcium phosphate bone cements (CPCs) for use in vertebroplasty to achieve effective primary fixation of spinal fractures. The incorporation of collagen, both bovine and from a marine sponge (Chondrosia reniformis), into a CPC was investigated. The biological properties of the CPC and collagen–CPC composites were assessed in vitro through the use of human bone marrow stromal cells. Cytotoxicity, proliferation, and osteoblastic differentiation were evaluated using lactate dehydrogenase, PicoGreen, and alkaline phosphatase activity assays, respectively. The addition of both types of collagen resulted in an increase in cytotoxicity, albeit not to a clinically relevant level. Cellular proliferation after 1, 7, and 14 days was unchanged. The osteogenic potential of the CPC was reduced through the addition of bovine collagen but remained unchanged in the case of the marine collagen. These findings, coupled with previous work showing that incorporation of marine collagen in this way can improve the physical properties of CPCs, suggest that such a composite may offer an alternative to CPCs in applications where low setting times and higher mechanical stability are important. © 2015 The Authors. Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc. 104B:308–315, 2015.

Bone cements for percutaneous vertebroplasty and balloon kyphoplasty: Current status and future developments

Osteoporotic vertebral compression fractures (OVCFs) have gradually evolved into a serious health care problem globally. In order to reduce the morbidity of OVCF patients and improve their life quality, two minimally invasive surgery procedures, vertebroplasty (VP) and balloon kyphoplasty (BKP), have been developed. Both VP and BKP require the injection of bone cement into the vertebrae of patients to stabilize fractured vertebra. As such, bone cement as the filling material plays an essential role in the effectiveness of these treatments. In this review article, we summarize the bone cements that are currently available in the market and those still under development. Two major categories of bone cements, nondegradable acrylic bone cements (ABCs) and degradable calcium phosphate cements (CPCs), are introduced in detail. We also provide our perspectives on the future development of bone cements for VP and BKP.

Experimental and computational approach investigating burst fracture augmentation using PMMA and calcium phosphate cements

The aim of the study was to use a computational and experimental approach to evaluate, compare and predict the ability of calcium phosphate (CaP) and poly (methyl methacrylate) (PMMA) augmentation cements to restore mechanical stability to traumatically fractured vertebrae, following a vertebroplasty procedure. Traumatic fractures (n = 17) were generated in a series of porcine vertebrae using a drop-weight method. The fractured vertebrae were imaged using μCT and tested under axial compression. Twelve of the fractured vertebrae were randomly selected to undergo a vertebroplasty procedure using either a PMMA (n = 6) or a CaP cement variation (n = 6). The specimens were imaged using μCT and re-tested. Finite element models of the fractured and augmented vertebrae were generated from the μCT data and used to compare the effect of fracture void fill with augmented specimen stiffness. Significant increases (p < 0.05) in failure load were found for both of the augmented specimen groups compared to the fractured group. The experimental and computational results indicated that neither the CaP cement nor PMMA cement could completely restore the vertebral mechanical behavior to the intact level. The effectiveness of the procedure appeared to be more influenced by the volume of fracture filled rather than by the mechanical properties of the cement itself.

Kyphopasty and vertebroplasty

Vertebroplasty and balloon kyphoplasty are percutaneous techniques performed under radioscopic control. They were initially developed for tumoral and osteoporotic lesions; indications were later extended to traumatology for the treatment of pure compression fracture. They are an interesting alternative to conventional procedures, which are often very demanding. The benefit of these minimally invasive techniques has been demonstrated in terms of alleviation of pain, functional improvement and reduction in both morbidity and costs for society. The principle of kyphoplasty is to restore vertebral body anatomy gently and progressively by inflating balloons and then reinforcing the anterior column of the vertebra with cement. In vertebroplasty, cement is introduced directly under pressure, without prior balloon inflation. Both techniques can be associated to minimally invasive osteosynthesis in certain indications. In our own practice, we preferably use acrylic cement, for its biomechanical properties and resistance to compression stress. We use calcium phosphate cement in young patients, but only associated to percutaneous osteosynthesis due to the risk of secondary correction loss. The evolution of these techniques depends on improving personnel radioprotection and developing new systems of vertebral expansion.

Management of thoracolumbar spine fractures

BACKGROUND CONTEXT

Traumatic fractures of the spine are most common at the thoracolumbar junction and can be a source of great disability.

PURPOSE

To review the most current information regarding the pathophysiology, injury pattern, treatment options, and outcomes.

STUDY DESIGN

Literature review.

METHODS

Relevant articles, textbook chapters, and abstracts covering thoracolumbar spine fractures with and without neurologic deficit from 1960 to the present were reviewed.

RESULTS

The thoracolumbar spine represents a unique system from a skeletal as well as neurological standpoint. The rigid rib-bearing thoracic spine articulates with the more mobile lumbar spine at the thoracolumbar junction (T10 - L2), the site of most fractures. A complete examination includes a careful neurologic examination of both motor and sensory systems. CT scans best describe bony detail while MRI is most efficient at describing soft tissues and neurological structures. The most recent classification system is that of the new Thoracolumbar Injury Classification and Severity Score. The different fracture types include compression fractures, burst fractures - both stable and unstable -, flexion-distraction injuries and fracture dislocations. Their treatment, both operative and non-operative depends on the degree of bony compromise, neurological involvement, and the integrity of the posterior ligamentous complex. Minimally invasive approaches to the care of thoracolumbar injuries have become more popular, thus, the evidence regarding their efficacy is presented. Finally, the treatment of osteoporotic fractures of the thoracolumbar spine is reviewed, including vertebroplasty and kyphoplasty, their risks and controversies, and senile burst fractures, as well.

CONCLUSIONS

Thoracolumbar spine fractures remain a significant source of potential morbidity. Advances in treatment have minimized the invasiveness of our surgery and in certain stable situations, eliminated it all together.

Investigating the Effects of Surface-Initiated Polymerization of ε-Caprolactone to Bioactive Glass Particles on the Mechanical Properties of Settable Polymer/Ceramic Composites

Injectable bone grafts with strength exceeding that of trabecular bone could improve the management of a number of orthopaedic conditions. Ceramic/polymer composites have been investigated as weight-bearing bone grafts, but they are typically weaker than trabecular bone due to poor interfacial bonding. We hypothesized that entrapment of surface-initiated poly(ε-caprolactone) (PCL) chains on 45S5 bioactive glass (BG) particles within an in situ-formed polymer network would enhance the mechanical properties of reactive BG/polymer composites. When the surface-initiated PCL molecular weight exceeded the molecular weight between crosslinks of the network, the compressive strength of the composites increased 6- to 10-fold. The torsional strength of the composites exceeded that of human trabecular bone by a factor of two. When injected into femoral condyle defects in rats, the composites supported new bone formation at 8 weeks. The initial bone-like strength of BG/polymer composites and their ability to remodel in vivo highlight their potential for development as injectable grafts for repair of weight-bearing bone defects.

Development of calcium phosphate cement for the augmentation of traumatically fractured porcine specimens using vertebroplasty

The study aim was to develop and apply an experimental technique to determine the biomechanical effect of polymethylmethacrylate (PMMA) and calcium phosphate (CaP) cement on the stiffness and strength of augmented vertebrae following traumatic fracture. Twelve burst type fractures were generated in porcine three-vertebra segments. The specimens were randomly split into two groups (n=6), imaged using microCT and tested under axial loading. The two groups of fractured specimens underwent a vertebroplasty procedure, one group was augmented with CaP cement designed and developed at Queen's University Belfast. The other group was augmented with PMMA cement (WHW Plastics, Hull, UK). The specimens were imaged and re-tested . An intact single vertebra specimen group (n=12) was also imaged and tested under axial loading. A significant decrease (p<0.01) was found between the stiffness of the fractured and intact groups, demonstrating that the fractures generated were sufficiently severe, to adversely affect mechanical behaviour. Significant increase (p<0.01) in failure load was found for the specimen group augmented with the PMMA cement compared to the pre-augmentation group, conversely, no significant increase (p<0.01) was found in the failure load of the specimens augmented with CaP cement, this is attributed to the significantly (p<0.05) lower volume of CaP cement that was successfully injected into the fracture, compared to the PMMA cement. The effect of the percentage of cement fracture fill, cement modulus on the specimen stiffness and ultimate failure load could be investigated further by using the methods developed within this study to test a more injectable CaP cement.

Development of a bovine collagen-apatitic calcium phosphate cement for potential fracture treatment through vertebroplasty

The aim of this study was to examine the potential of incorporating bovine fibres as a means of reinforcing a typically brittle apatite calcium phosphate cement for vertebroplasty. Type I collagen derived from bovine Achilles tendon was ground cryogenically to produce an average fibre length of 0.96±0.55 mm and manually mixed into the powder phase of an apatite-based cement at 1, 3 or 5 wt.%. Fibre addition of up to 5 wt.% had a significant effect (P ≤ 0.001) on the fracture toughness, which was increased by 172%. Adding ≤ 1 wt.% bovine collagen fibres did not compromise the compressive properties significantly, however, a decrease of 39-53% was demonstrated at ≥ 3wt.% fibre loading. Adding bovine collagen to the calcium phosphate cement reduced the initial and final setting times to satisfy the clinical requirements stated for vertebroplasty. The cement viscosity increased in a linear manner (R²=0.975) with increased loading of collagen fibres, such that the injectability was found to be reduced by 83% at 5 wt.% collagen loading. This study suggests for the first time the potential application of a collagen-reinforced calcium phosphate cement as a viable option in the treatment of vertebral fractures, however, issues surrounding efficacious cement delivery need to be addressed.

An approximate model for cancellous bone screw fixation

This paper presents a finite element (FE) model to identify parameters that affect the performance of an improved cancellous bone screw fixation technique, and hence potentially improve fracture treatment. In cancellous bone of low apparent density, it can be difficult to achieve adequate screw fixation and hence provide stable fracture fixation that enables bone healing. Data from predictive FE models indicate that cements can have a significant potential to improve screw holding power in cancellous bone. These FE models are used to demonstrate the key parameters that determine pull-out strength in a variety of screw, bone and cement set-ups, and to compare the effectiveness of different configurations. The paper concludes that significant advantages, up to an order of magnitude, in screw pull-out strength in cancellous bone might be gained by the appropriate use of a currently approved calcium phosphate cement.

In vitro studies of composite bone filler based on poly(propylene fumarate) and biphasic α-tricalcium phosphate/hydroxyapatite ceramic powder

While many different filler materials have been applied in vertebral augmentation procedures, none is perfect in all biomechanical and biological characteristics. To minimize possible shortages, we synthesized a new biodegradable, injectable, and premixed composite made from poly(propylene fumarate) (PPF) and biphasic α-tricalcium phosphate (α-TCP)/hydroxyapatite (HAP) ceramics powder and evaluated the material properties of the compound in vitro. We mixed the PPF cross-linked by N-vinyl pyrrolidinone and biphasic α-TCP/HAP powder in different ratios with benzoyl peroxide as an initiator. The setting time and temperature were recorded, although they could be manipulated by modulating the concentrations of hydroquinone and N,N-dimethyl-p-toluidine. Degradation, cytocompatibility, mechanical properties, and radiopacity were analyzed after the composites were cured by a cylindrical shape. We also compared the study materials with poly(methyl methacrylate) (PMMA) and PPF with pure HAP particles. Results showed that lower temperature during curing process (38-44°C), sufficient initial mechanical compressive fracture strength (61.1±3.7MPa), and gradual degradation were observed in the newly developed bone filler. Radiopacity in Hounsfield units was similar to PMMA as determined by computed tomography scan. Both pH value variation and cytotoxicity were within biological tolerable limits based on the biocompatibility tests. Mixtures with 70% α-TCP/HAP powder were superior to other groups. This study indicated that a composite of PPF and biphasic α-TCP/HAP powder is a promising, premixed, injectable biodegradable filler and that a mixture containing 70% α-TCP/HAP exhibits the best properties.

An improved collagen scaffold for skeletal regeneration

Bone repair and regeneration is one of the most extensively studied areas in the field of tissue engineering. All of the current tissue engineering approaches to create bone focus on intramembranous ossification, ignoring the other mechanism of bone formation, endochondral ossification. We propose to create a transient cartilage template in vitro, which could serve as an intermediate for bone formation by the endochondral mechanism once implanted in vivo. The goals of the study are (1) to prepare and characterize type I collagen sponges as a scaffold for the cartilage template, and (2) to establish a method of culturing chondrocytes in type I collagen sponges and induce cell maturation. Collagen sponges were generated from a 1% solution of type I collagen using a freeze/dry technique followed by UV light crosslinking. Chondrocytes isolated from two locations in chick embryo sterna were cultured in these sponges and treated with retinoic acid to induce chondrocyte maturation and extracellular matrix deposition. Material strength testing as well as microscopic and biochemical analyzes were conducted to evaluate the properties of sponges and cell behavior during the culture period. We found that our collagen sponges presented improved stiffness and supported chondrocyte attachment and proliferation. Cells underwent maturation, depositing an abundant extracellular matrix throughout the scaffold, expressing high levels of type X collagen, type I collagen and alkaline phosphatase. These results demonstrate that we have created a transient cartilage template with potential to direct endochondral bone formation after implantation.

Optimisation of the mechanical and handling properties of an injectable calcium phosphate cement

Calcium phosphate cements have the potential to be successful in minimally invasive surgical techniques, like that of vertebroplasty, due to their ability to be injected into a specific bone cavity. These bone cements set to produce a material similar to that of the natural mineral component in bone. Due to the ceramic nature of these materials they are highly brittle and it has been found that they are difficult to inject. This study was carried out to determine the factors that have the greatest effect on the mechanical and handling properties of an apatitic calcium phosphate cement with the use of a Design of Experiments (DoE) approach. The properties of the cement were predominantly influenced by the liquid:powder ratio and weight percent of di-sodium hydrogen phosphate within the liquid phase. An optimum cement composition was hypothesised and tested. The mechanical properties of the optimised cement were within the clinical range for vertebroplasty, however, the handling properties still require improvement.

Characterization of polymeric solutions as injectable vehicles for hydroxyapatite microspheres

A polymeric solution and a reinforcement phase can work as an injectable material to fill up bone defects. However, the properties of the solution should be suitable to enable the transport of that extra phase. Additionally, the use of biocompatible materials is a requirement for tissue regeneration. Thus, we intended to optimize a biocompatible polymeric solution able to carry hydroxyapatite microspheres into bone defects using an orthopedic injectable device. To achieve that goal, polymers usually regarded as biocompatible were selected, namely sodium carboxymethylcellulose, hydroxypropylmethylcellulose, and Na-alginate (ALG). The rheological properties of the polymeric solutions at different concentrations were assessed by viscosimetry before and after moist heat sterilization. In order to correlate rheological properties with injectability, solutions were tested using an orthopedic device applied for minimal invasive surgeries. Among the three polymers, ALG solutions presented the most suitable properties for our goal and a non-sterile ALG 6% solution was successfully used to perform preliminary injection tests of hydroxyapatite microspheres. Sterile ALG 7.25% solution was found to closely match non-sterile ALG 6% properties and it was selected as the optimal vehicle. Finally, sterile ALG 7.25% physical stability was studied at different temperatures over a 3-month period. It was observed that its rheological properties presented minor changes when stored at 25 degrees C or at 4 degrees C.

Thoracolumbar burst fractures: a systematic review of management

The management of thoracolumbar burst fractures remains challenging. Ideally, it should effectively correct the deformity, induce neurological recovery, allow early mobilization and return to work, and be associated with minimal risk of complication. This article reviews the related studies reporting their clinical data for the management of thoracolumbar burst fractures, discusses the most suitable approach in cases such as these, highlights specific treatment recommendations, and proposes a treatment algorithm. Using PubMed and Scopus databases to search the term thoracolumbar burst fractures, abstracts and original articles in English investigating the treatment of thoracolumbar burst fractures were searched and analyzed.

Retrospective multicenter study of surgical treatments for osteoporotic vertebral fractures

BACKGROUND

Although many surgical procedures are available for treating osteoporotic vertebral fractures, there have been no comprehensive multicenter surveys in Japan focusing on surgical treatments for these fractures. This study aimed at (1) conducting a retrospective multicenter study to survey surgical treatments performed at referral center hospitals in various regions in Japan and (2) analyzing situations and problems related to the surgical treatments of osteoporotic vertebral fractures in Japanese hospitals.

METHODS

Among 738 patients who were hospitalized in 13 hospitals in various regions in Japan between 2005 and 2006 for osteoporotic vertebral fractures, 84 patients (11.4%) who underwent spinal surgery were enrolled. These patients were retrospectively analyzed regarding cause of injury, preoperative symptoms, preoperative neurological function, surgical procedures, periods of bed rest, length of hospital stay, and ambulatory status at discharge from hospital.

RESULTS

As to the cause of spinal fracture, 38 patients (45% of the surgical patients) could not identify a specific cause of their spinal fracture. Preoperative neurological motor weakness in legs was observed in 41 (49%). With regard to surgical treatment, posterior spinal reconstruction surgery was performed in 50 patients (60%), vertebroplasty in 26 (31%), anterior reconstruction surgery in 6 (7%), anterior and posterior combined reconstruction surgery in 1, and posterior decompression alone in 1 patient. In all, 70 patients (83.3%), whose periods of hospital stay averaged 52.8 days, could walk by themselves at the time of discharge; 14 (16.7%), whose periods of hospital stay averaged 44.7 days, could not walk by themselves at the time of discharge.

CONCLUSIONS

Even after a large variety of surgical procedures were tried to treat osteoporotic vertebral fractures and long hospital stays, about 17% of the patients were unable to walk by themselves at the time of discharge from hospital.

Osteoblast response to polymethyl methacrylate bioactive glass composite

Polymethylmethacrylate (PMMA) has been used in many orthopedic and dental applications since the 1960s. Biocompatibility of newly developed surface porous fiber reinforced (SPFR) PMMA based composite has not been previously proven in cell culture environment. Analysis of rat bone marrow stromal cells grown on the different test materials showed only little difference in normalized cell activity or bone sialoprotein (BSP) production between the test materials, but the osteocalcin (OC) levels remained higher (P < 0.015-0.005) through out the test with SPFR-material when compared to tissue culture poly styrene (TCPS). The cells grown on SP-FRC material also showed highest calcium depletion from the culture medium (P < 0.026-0.001) when compared to all other test substrates. SEM images of the cultured samples confirmed that all the materials enabled cell spreading and growth on their surface, but the roughened surface remarkably enhanced this process of cell attachment, division and calcified nodule formation. This study shows that the SP-FRC composite material does not elicit harmful/toxic reactions in cell cultures more than neutral TCPS and can be considered biocompatible. The material possesses good capabilities to form new mineralized tissue onto its surface, and through that a possibility to bond directly to bone. Rough surface seems to enhance osteoblast proliferation and formation of mineralized extracellular matrix.

Variations in astrocyte and fibroblast response due to biomaterial particulates in vitro

The possible involvement of orthopedic biomaterial particles such as cobalt-chrome alloy (Co-Cr), ultrahigh molecular weight polyethylene (UHMWPE), titanium alloy (Ti-6Al-4V), and polymethyl methacrylate (PMMA) in the formation of glial and meningeal scars was investigated using an in vitro system. Cell lines were used as models for astrocytes and meningeal fibroblasts. They were incubated with varying concentrations of particle suspensions, after which proliferative and cytotoxic responses were quantified using MTT assay and Live/Dead microscopy. It was determined that relative particulate toxicity (arranged in decreasing order) to astrocytes is Co-Cr > Ti-6Al-4V > PMMA > UHMWPE, and toxicity to fibroblasts is PMMA > Co-Cr > Ti-6Al-4V > UHMWPE. Cell death caused by PMMA was mainly due to necrosis, while the rest of the particles induced apoptosis. Low quantities of Co-Cr and Ti-6Al-4V stimulate increased astrocyte proliferation rate. However, only the cells treated with titanium alloy caused upregulated transcription of reactive astrocyte markers such as glial fibrillary acidic protein, vimentin, nestin, and type IV collagen, suggesting the potential of titanium alloy alone to trigger glial scarring. None of the biomaterials tested promoted proliferation in fibroblasts implying that biomaterial particles are not directly involved in meningeal scar development.

Beta-tricalcium phosphate release from brushite cement surface

Different in vivo studies demonstrated that brushite cements are biocompatible, bioresorbable, and osteoconductive. However, the decay of brushite cements has been scarcely studied even though it may be of great concern for clinical applications in highly blood-perfused regions. This work was elaborated to elucidate factors that determine brushite cement surface disintegration. For that, brushite cements were modified using in their preparation different aqueous solutions of phosphoric, glycolic, tartaric, and citric acids in concentrations that were reported to improve the cement properties. Two-viscosity enhancing polysaccharides, chondroitin-4 sulfate and hyaluronic acid, were also assayed. Thereafter, pre- and set cement samples were immersed in distilled water for 24 h. The cement-solid weight loss, microstructure, liquid phase viscosity, mean size of the released particles, and zeta potential were analyzed using X-ray diffraction, FTIR spectroscopy, light scattering, scanning electron microscopy and optical microscopy. It was found that the particles released from the cement surface were beta-TCP, and their amount depends on the carboxylic acid used in the preparation of the cement. The addition of hyaluronic acid and chondroitin-4 sulfate decreased the amount of released particles from the surface of the set brushite cement made with citric acid. Furthermore, the hyaluronic acid increased significantly the viscosity of the citric acid solution and the cement paste prepared with this liquid phase showed a pronounced step down in particle release. In this study, we showed that the water solubility of calcium carboxylate and the viscosity of mixing liquid may dictate the superficial disintegration of brushite cements.

Vertebroplastie und Kyphoplastie bei osteoporotischen Wirbelkörperfrakturen: Gesicherte Kenntnisse, offene Fragen

Cementoplasty, performed either as percutaneous vertebroplasty or kyphoplasty, has become well established as an effective technique to treat painful vertebral body fractures. It has low complication rates, is successful in alleviating pain, and improves the patients' mobility and quality of life. A series of questions remain open though or are the subject of controversial debate; for example, the results of several biomechanical studies are in part contradictory. Clinical data on subsequent fractures are also still inadequate, although the majority of studies show no elevated rate of subsequent fractures following treatment with cementoplasty in comparison to the natural course in patients with osteoporotic fractures. Kyphoplasty has the advantage of being able to restore the vertebral body height or reduce the kyphosis angle without leading to different clinical outcomes in comparison to vertebroplasty. Biomechanical considerations on whether restoration of the vertebral body's normal shape could reduce the rate of subsequent fractures still need scientific substantiation. Both surgical methods are employed in our clinic. Kyphoplasty seems to us to be indicated when the height of the anterior portion of the vertebral body is reduced by one-third compared to the norm or a kyphosis angle of more than 15-20 degrees is present. The goals of therapy are restoring the shape and reducing the kyphosis angle. This can only succeed, however, in fractures that are not older than 3 weeks. In all other cases vertebroplasty is performed.