Dynamic force microscopy imaging of plasmid DNA and viral RNA

Mechanisms of Plasma Ozone and UV-C Sterilization of SARS-CoV-2 Explored through Atomic Force Microscopy

Ultraviolet-C (UV-C) radiation and ozone gas are potential mechanisms employed to inactivate the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), each exhibiting distinct molecular-level modalities of action. To elucidate these disparities and deepen our understanding, we delve into the intricacies of SARS-CoV-2 inactivation via UV-C and ozone gas treatments, exploring their distinct molecular-level impacts utilizing a suite of advanced techniques, including biological atomic force microscopy (Bio-AFM) and single virus force spectroscopy (SVFS). Whereas UV-C exhibited no perceivable alterations in virus size or surface topography, ozone gas treatment elucidated pronounced changes in both parameters, intensifying with prolonged exposure. Furthermore, a nuanced difference was observed in virus-host cell binding post-treatment: ozone gas distinctly reduced SARS-CoV-2 binding to host cells, while UV-C maintained the status quo. The results derived from these methodical explorations underscore the pivotal role of advanced Bio-AFM techniques and SVFS in enhancing our understanding of virus inactivation mechanisms, offering invaluable insights for future research and applications in viral contamination mitigation.

Analytical separation of plasmid DNA isoforms using anion exchanging chromatographic monoliths with 6 µm channels

High-performance liquid chromatography (HPLC)-based analytical assays are used to effectively monitor purity and quantity of plasmid DNA (pDNA) throughout the purification process. However, the phenomenon of physical entrapment of open circular (OC) isoforms pDNA inside narrow channels of chromatographic support decreases its accuracy and precision and the effect increases with pDNA size. The purpose of the study was to develop a chromatographic method for accurate analytical separation between isoforms of <16 kbp pDNA using weak anion exchanging monolithic column with large (6 µm) convective channels. Purified samples of 4.7 and 15.4 kbp large pDNA with known isoform composition were prepared and their isoforms separated in ascending salt gradient. Both OC and supercoiled (SC) isoforms were baseline separated at a flow rate below 0.5 mL min-1 in a guanidinium chloride (GdnCl) gradient with a ≥95% OC pDNA elution recovery. However, these chromatographic conditions increased 2 times the peak width for linear (LIN) pDNA isoform compared to the results using monoliths with 1.4 µm channel size. If other chaotropic agents, such as urea or thiocyanate (SCN), were added to Gdn ions, the elution volume for LIN isoform decreased. Optimization of combined GdnCl/GdnSCN gradient for pDNA elution resulted in a simple and robust chromatographic method, where OC-LIN and LIN-SC pDNA (up to 15 kbp size) were separated with resolution above 1.0 and above 2.0, respectively. The accessibility and general acceptance of anion exchange chromatography for pDNA analytics give the newly developed method a great potential for in-process control monitoring of pDNA production processes.

Characterization of structures and molecular interactions of RNA and lipid carriers using atomic force microscopy

Ribonucleic acid (RNA) and lipid are essential biomolecules in many biological processes, and hold a great prospect for biomedical applications, such as gene therapy, vaccines and therapeutic drug delivery. The characterization of morphology and intra-/inter-molecular interactions of RNA and lipid molecules is critical for understanding their functioning mechanisms. Atomic force microscopy (AFM) is a sophisticated technique for characterizing biomolecules featured by its piconewton force sensitivity, sub-nanometer spatial resolution, and flexible operation conditions in both air and liquid. The goal of this review is to highlight the representative and outstanding discoveries of the characterization of RNA and lipid molecules through morphology identification, physicochemical property determination and intermolecular force measurements by AFM. The first section introduces the AFM imaging of RNA molecules to obtain high-resolution morphologies and nanostructures in air and liquid, followed by the discussion of employing AFM force spectroscopy in understanding the nanomechanical properties and intra-/inter-molecular interactions of RNA molecules, including RNA-RNA and RNA-biomolecule interactions. The second section focuses on the studies of lipid and RNA encapsulated in lipid carrier (RNA-lipid) by AFM as well as the sample preparation and factors influencing the morphology and structure of lipid/RNA-lipid complexes. Particularly, the nanomechanical properties of lipid and RNA-lipid characterized by nanomechanical imaging and force measurements are discussed. The future perspectives and remaining challenges on the characterization of RNA and lipid offered by the versatile AFM techniques are also discussed. This review provides useful insights on the characterization of RNA and lipids nanostructures along with their molecular interactions, and also enlightens the application of AFM techniques in investigating a broad variety of biomolecules.

Investigation of HIV-1 Gag binding with RNAs and lipids using Atomic Force Microscopy

Atomic Force Microscopy was utilized to study the morphology of Gag, ΨRNA, and their binding complexes with lipids in a solution environment with 0.1Å vertical and 1nm lateral resolution. TARpolyA RNA was used as a RNA control. The lipid used was phospha-tidylinositol-(4,5)-bisphosphate (PI(4,5)P2). The morphology of specific complexes Gag-ΨRNA, Gag-TARpolyA RNA, Gag-PI(4,5)P2 and PI(4,5)P2-ΨRNA-Gag were studied. They were imaged on either positively or negatively charged mica substrates depending on the net charges carried. Gag and its complexes consist of monomers, dimers and tetramers, which was confirmed by gel electrophoresis. The addition of specific ΨRNA to Gag is found to increase Gag multimerization. Non-specific TARpolyA RNA was found not to lead to an increase in Gag multimerization. The addition PI(4,5)P2 to Gag increases Gag multimerization, but to a lesser extent than ΨRNA. When both ΨRNA and PI(4,5)P2 are present Gag undergoes comformational changes and an even higher degree of multimerization.

Bis(dipyrrinato)zinc(II) Complex Chiroptical Wires: Exfoliation into Single Strands and Intensification of Circularly Polarized Luminescence

One-dimensional (1D) coordination polymers (CPs) experiences limitations in exfoliation into individual strands, which hamper their utility as functional 1D nanomaterials. Here we synthesize chiral 1D-CPs that feature the bis(dipyrrinato)zinc(II) complex motif. They can be exfoliated into single strands upon sonication in organic media, retaining lengths of up to 3.19 μm (ca. 2600 monomer units). Their chiroptical structure allows the exfoliated wires to show circularly polarized luminescence at an intensity 5.9 times that of reference monomer complexes.

Utilising inorganic nanocarriers for gene delivery

The delivery of genetic materials into cells to elicit cellular response has been extensively studied by biomaterials scientists globally.

Sequential binding of FurA from Anabaena sp. PCC 7120 to iron boxes: exploring regulation at the nanoscale

Fur (ferric uptake regulator) proteins are involved in the control of a variety of processes in most prokaryotes. Although it is assumed that this regulator binds its DNA targets as a dimer, the way in which this interaction occurs remains unknown. We have focused on FurA from the cyanobacterium Anabaena sp. PCC 7120. To assess the molecular mechanism by which FurA specifically binds to "iron boxes" in PfurA, we examined the topology arrangement of FurA-DNA complexes by atomic force microscopy. Interestingly, FurA-PfurA complexes exhibit several populations, in which one is the predominant and depends clearly on the regulator/promoter ratio on the environment. Those results together with EMSA and other techniques suggest that FurA binds PfurA using a sequential mechanism: (i) a monomer specifically binds to an "iron box" and bends PfurA; (ii) two situations may occur, that a second FurA monomer covers the free "iron box" or that joins to the previously used forming a dimer which would maintain the DNA kinked; (iii) trimerization in which the DNA is unbent; and (iv) finally undergoes a tetramerization; the next coming molecules cover the DNA strands unspecifically. In summary, the bending appears when an "iron box" is bound to one or two molecules and decreases when both "iron boxes" are covered. These results suggest that DNA bending contributes at the first steps of FurA repression promoting the recruitment of new molecules resulting in a fine regulation in the Fur-dependent cluster associated genes.

Atomic force microscopy imaging of macromolecular complexes

This chapter reviews amplitude modulation (AM) AFM in air and its applications to high-resolution imaging and interpretation of macromolecular complexes. We discuss single DNA molecular imaging and DNA-protein interactions, such as those with topoisomerases and RNA polymerase. We show how relative humidity can have a major influence on resolution and contrast and how it can also affect conformational switching of supercoiled DNA. Four regimes of AFM tip-sample interaction in air are defined and described, and relate to water perturbation and/or intermittent mechanical contact of the tip with either the molecular sample or the surface. Precise control and understanding of the AFM operational parameters is shown to allow the user to switch between these different regimes: an interpretation of the origins of topographical contrast is given for each regime. Perpetual water contact is shown to lead to a high-resolution mode of operation, which we term SASS (small amplitude small set-point) imaging, and which maximizes resolution while greatly decreasing tip and sample wear and any noise due to perturbation of the surface water. Thus, this chapter provides sufficient information to reliably control the AFM in the AM AFM mode of operation in order to image both heterogeneous samples and single macromolecules including complexes, with high resolution and with reproducibility. A brief introduction to AFM, its versatility and applications to biology is also given while providing references to key work and general reviews in the field.

Binding and translocation of termination factor rho studied at the single-molecule level

Rho termination factor is an essential hexameric helicase responsible for terminating 20-50% of all mRNA synthesis in Escherichia coli. We used single-molecule force spectroscopy to investigate Rho-RNA binding interactions at the Rho utilization site of the λtR1 terminator. Our results are consistent with Rho complexes adopting two states: one that binds 57 ± 2nt of RNA across all six of the Rho primary binding sites, and another that binds 85 ± 2nt at the six primary sites plus a single secondary site situated at the center of the hexamer. The single-molecule data serve to establish that Rho translocates 5'→3' toward RNA polymerase (RNAP) by a tethered-tracking mechanism, looping out the intervening RNA between the Rho utilization site and RNAP. These findings lead to a general model for Rho binding and translocation and establish a novel experimental approach that should facilitate additional single-molecule studies of RNA-binding proteins.

The intrinsic resolution limit in the atomic force microscope: implications for heights of nano-scale features

BACKGROUND

Accurate mechanical characterization by the atomic force microscope at the highest spatial resolution requires that topography is deconvoluted from indentation. The measured height of nanoscale features in the atomic force microscope (AFM) is almost always smaller than the true value, which is often explained away as sample deformation, the formation of salt deposits and/or dehydration. We show that the real height of nano-objects cannot be obtained directly: a result arising as a consequence of the local probe-sample geometry.

METHODS AND FINDINGS

We have modeled the tip-surface-sample interaction as the sum of the interaction between the tip and the surface and the tip and the sample. We find that the dynamics of the AFM cannot differentiate between differences in force resulting from 1) the chemical and/or mechanical characteristics of the surface or 2) a step in topography due to the size of the sample; once the size of a feature becomes smaller than the effective area of interaction between the AFM tip and sample, the measured height is compromised. This general result is a major contributor to loss of height and can amount to up to ∼90% for nanoscale features. In particular, these very large values in height loss may occur even when there is no sample deformation, and, more generally, height loss does not correlate with sample deformation. DNA and IgG antibodies have been used as model samples where experimental height measurements are shown to closely match the predicted phenomena.

CONCLUSIONS

Being able to measure the true height of single nanoscale features is paramount in many nanotechnology applications since phenomena and properties in the nanoscale critically depend on dimensions. Our approach allows accurate predictions for the true height of nanoscale objects and will lead to reliable mechanical characterization at the highest spatial resolution.

Time-resolved chloroquine-induced relaxation of supercoiled plasmid DNA

Herein, we report on the in vitro change of DNA conformation of plasmids bound to a 3-aminopropyl-modified mica surface and monitoring the events by atomic force microscopy (AFM) imaging under near physiological conditions. In our study, we used an intercalating drug, chloroquine, which is known to decrease the twist of the double helix and thus altered the conformation of the whole DNA. During our experiments, a chloroquine solution was added while imaging a few highly condensed plasmid nanoparticles in solution. AFM images recorded after the drug addition clearly show a time-resolved relaxation of these bionanoparticles into a mixture of loose DNA strands.

Directed formation of DNA nanoarrays through orthogonal self-assembly

We describe the synthesis of terpyridine modified DNA strands which selectively form DNA nanotubes through orthogonal hydrogen bonding and metal complexation interactions. The short DNA strands are designed to self-assemble into long duplexes through a sticky-end approach. Addition of weakly binding metals such as Zn(II) and Ni(II) induces the formation of tubular arrays consisting of DNA bundles which are 50-200 nm wide and 2-50 nm high. TEM shows additional long distance ordering of the terpy-DNA complexes into fibers.

Imaging of nucleic acids with atomic force microscopy

Atomic force microscopy (AFM) is a key tool of nanotechnology with great importance in applications to DNA nanotechnology and to the recently emerging field of RNA nanotechnology. Advances in the methodology of AFM now enable reliable and reproducible imaging of DNA of various structures, topologies, and DNA and RNA nanostructures. These advances are reviewed here with emphasis on methods utilizing modification of mica to prepare the surfaces enabling reliable and reproducible imaging of DNA and RNA nanostructures. Since the AFM technology for DNA is more mature, AFM imaging of DNA is introduced in this review to provide experience and background for the improvement of AFM imaging of RNA. Examples of imaging different structures of RNA and DNA are discussed and illustrated. Special attention is given to the potential use of AFM to image the dynamics of nucleic acids at the nanometer scale. As such, we review recent advances with the use of time-lapse AFM.

Facile synthesis of monodispersed mesoporous silica nanoparticles with ultralarge pores and their application in gene delivery

Among various nanoparticles, the silica nanoparticle (SiNP) is an attractive candidate as a gene delivery carrier due to advantages such as availability in porous forms for encapsulation of drugs and genes, large surface area to load biomacromolecules, biocompatibility, storage stability, and easy preparation in large quantity with low cost. Here, we report on a facile synthesis of monodispersed mesoporous silica nanoparticles (MMSN) possessing very large pores (>15 nm) and application of the nanoparticles to plasmid DNA delivery to human cells. The aminated MMSN with large pores provided a higher loading capacity for plasmids than those with small pores (∼2 nm), and the complex of MMSN with plasmid DNA readily entered into cells without supplementary polymers such as cationic dendrimers. Furthermore, MMSN with large pores could efficiently protect plasmids from nuclease-mediated degradation and showed much higher transfection efficiency of the plasmids encoding luciferase and green fluorescent protein (pLuc, pGFP) compared to MMSN with small pores (∼2 nm).

Three powerful research tools from single cells into single molecules: AFM, laser tweezers, and Raman spectroscopy

By using three physical techniques (atomic force microscopy (AFM), laser tweezers, and Raman spectroscopy), many excellent works in single-cell/molecule research have been accomplished. In this review, we present a brief introduction to the principles of these three techniques, and their capabilities toward single-cell/molecule research are highlighted. Afterward, the advances in single-cell/molecule research that have been facilitated by these three techniques are described. Following this, their complementary assets for single-cell/molecule research are analyzed, and the necessity of integrating the functions of these three techniques into one instrument is proposed.

Phase imaging atomic force microscopy in the characterization of biomaterials

The phase imaging atomic force microscopy is a powerful tool in surface characterization of the biomaterials, and the resulting phase image is able to detect chemical variation and reveal more detailed surface properties than the morphological image. However, the chemical- and morphological-dependent phase images were still not distinguished well. In order to better understand actual occurring phase images, we examined non-carious human maxillary incisor, microphase separated polyurethane and self-assembling peptide nanofibres. We herein reported that phase image mainly plotted the morphological change: the phase peak corresponding to the morphological valley, and the morphological peak to the phase valley, and exhibited fine surface structures of materials. The chemical-dependent phase contrast was generally masked by their inherent roughness. For the sample being very rough and having great phase separation, its chemical-dependent phase contrast could be detected at the hard tapping mode ('Amp. Ref. "set point ratio"': -0.4 to -0.8), for the sample with medium roughness only at the light tapping mode ('Amp. Ref.': -0.1 to -0.4). These results will help us understand and determine actual occurring phase images of natural or fabricated biomaterials, even, other materials.

Specific DNA-protein interactions on mica investigated by atomic force microscopy

DNA processing by site-specific proteins on surface remains a challenging issue for nanobioscience applications and, in particular, for high-resolution imaging by atomic force microscopy (AFM). To obtain high-resolution conditions, mica, an atomically flat and negatively charged surface, is generally used. However, even though many specific DNA/protein interactions have already been observed by AFM, little is known about DNA accessibility to specific enzymes on mica. Here we measured the accessibility of adsorbed DNA to restriction endonucleases (EcoRI and EcoRV) using AFM. By increasing the concentration of divalent or multivalent salts, DNA adsorption on mica switches from weak to strong binding. Interestingly, while the accessibility of strongly bound DNA was inhibited, loosely adsorbed DNA was efficiently cleaved on mica. This result opens new perspective to study DNA/protein interaction by AFM or to modify specifically DNA on surface.