Hydrolysis of cellulose over functionalized glucose-derived carbon catalyst in ionic liquid

Simultaneous saccharification of hemicellulose and cellulose of corncob in a one-pot system using catalysis of carbon based solid acid from lignosulfonate

The drive towards sustainable chemistry has inspired the development of active solid acids as catalysts and ionic liquids as solvents for an efficient release of sugars from lignocellulosic biomass for future biorefinery practices. Carbon-based solid acid (SI-C-S-H2O2) prepared from sodium lignosulfonate, a waste of the paper industry, was used with water or ionic liquid to hydrolyze corncob in this study. The effects of various reaction parameters were investigated in different solvent systems. The highest xylose yield of 83.4% and hemicellulose removal rate of 90.6% were obtained in an aqueous system at 130 °C for 14 h. After the pretreatment, cellulase was used for the hydrolysis of residue and the enzymatic digestibility of 92.6% was obtained. Following these two hydrolysis steps in the aqueous systems, the highest yield of total reducing sugar (TRS) was obtained at 88.1%. Further, one-step depolymerization and saccharification of corncob hemicellulose and cellulose to reducing sugars in an IL-water system catalyzed by SI-C-S-H2O2 was conducted at 130 °C for 10 h, with a high TRS yield of 75.1% obtained directly. After recycling five times, the solid acid catalyst still showed a high catalytic activity for sugar yield in different systems, providing a green and effective method for lignocellulose degradation.

Plant-Biomass-Derived Carbon Materials as Catalyst Support, A Brief Review

Carbon materials are widely used in catalysis as effective catalyst supports. Carbon supports can be produced from coal, organic precursors, biomass, and polymer wastes. Biomass is one of the promising sources used to produce carbon-based materials with a high surface area and a hierarchical structure. In this review, we briefly discuss the methods of biomass-derived carbon supported catalyst preparation and their application in biodiesel production, organic synthesis reactions, and electrocatalysis.

Conversion of cellulose into valuable chemicals using sulfonated amorphous carbon in 1-ethyl-3-methylimidazolium chloride

In this study, three carbon-based solid acid catalysts were prepared via the one-step hydrothermal procedure using glucose and Brønsted acid, including sulfuric acid, p-toluenesulfonic acid, or hydrochloric acid. The as-synthesized catalysts were tested for their ability to convert cellulose into valuable chemicals. The effects of Brønsted acidic catalyst, catalyst loading, solvent, temperature, time, and reactor on the reaction were investigated. The as-synthesized C-H₂SO₄ catalyst containing Brønsted acid sites (-SO₃H, -OH, and -COOH functional groups) demonstrated high activity in the transformation of cellulose into valuable chemicals with the yield of total products of 88.17% including 49.79% LA in 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) solvent at 120 °C in 24 h. The recyclability and stability of C-H₂SO₄ were also observed. A proposed mechanism of cellulose conversion into valuable chemicals in the presence of C-H₂SO₄ was presented. The current method could provide a feasible approach for the conversion of cellulose into valuable chemicals.

Solvent-Assisted Adsorption of Cellulose on a Carbon Catalyst as a Pretreatment Method for Hydrolysis to Glucose

Cellulose hydrolysis to glucose using a heterogeneous catalyst is a necessary step in producing bio-based chemicals and polymers. The requirement for energy-intensive pretreatments, such as ball milling, to increase the reactivity of cellulose is one of the major issues in this area. Here, we show that by using solvent-assisted adsorption as a pretreatment step, cellulose can be adsorbed on the surface of a carbon catalyst. For adsorption pretreatment, phosphoric acid (H3PO4) performed better than other solvents such as sulfuric acid (H2SO4), tetrabutylammonium fluoride/dimethyl sulfoxide (TBAF/DMSO) and 1-butyl-3-methylimidazolium chloride ([BMMI]Cl). Hydrolysis after the adsorption of cellulose and the removal of H3PO4 produced a 73% yield of glucose. Partial hydrolysis of cellulose in H3PO4 before adsorption increased the final glucose yield. The glucose yield was proportional to the number of weakly acidic functional groups on the carbon catalyst, indicating the reaction was heterogeneously catalyzed. In a preliminary lab-scale life-cycle analysis (LCA), greenhouse gas (GHG) emissions per kg of glucose produced through the hydrolysis of cellulose were calculated. The H3PO4-assisted adsorption notably reduces GHG emissions compared to the previously reported ball milling pretreatment.

Microwave-assisted catalytic conversion of chitin to 5-hydroxymethylfurfural using polyoxometalate as catalyst

The key challenges for converting chitin to 5-hydroxymethylfurfural (5-HMF) include the low 5-HMF yield. Moreover, the disadvantages of traditional acid-base catalysts including complex post-treatment processes, the production of by-products, and severe equipment corrosion also largely limit the large-scale conversion of chitin to 5-HMF. In this view, herein we have demonstrated a microwave aided efficient and green conversion of chitin to 5-HMF while using polyoxometalate (POM) as a catalyst and DMSO/water as solvent. Chitin treated with H2SO4 followed by ball-milling (chitin-H2SO4-BM) was selected as the starting compound for the conversion process. Four different POMs including H3[PW12O40], H3[PMo12O40], H4[SiW12O40] and H4[SiMo12O40] were used as catalysts. Various reaction parameters including reaction temperature, amount of catalyst, mass ratios of water/DMSO and reaction time have been investigated to optimize the 5-HMF conversion. The H4[SiW12O40] catalyst exhibited the highest catalytic performance with 23.1% HMF yield at optimum operating conditions which is the highest among the literature for converting chitin to 5-HMF. Significantly, the disadvantages of the state of the art conversion routes described earlier can be overcome using POM-based catalysts, which makes the process more attractive to meet the ever-increasing energy demands, in addition to helping consume crustacean waste.

Intensified wheat husk conversion employing energy-efficient hybrid electromagnetic radiations for production of fermentable sugar: process optimization and life cycle assessment

This article reports an energy-efficient green pathway for the sustainable conversion of an abundant agro-residue viz. wheat husk (WH) into fermentable sugar (FS). The intensification effects of tungsten-halogen (TH) (150 W) and ultraviolet (UV) (100 W) irradiations on the pretreatment and subsequent hydrolysis of WH have been experimented with and optimized by Taguchi Orthogonal Design Array (TODA). In this study, two commercial catalysts, viz. Amberlyst-15 (A15) and nano-anataseTiO₂ (NAT) have been used in varying concentrations for the WH conversion process in a novel TH-UV radiated rotating reactor (THUVRR). At optimized peracetic acid pretreatment conditions [90 °C reaction temperature; 1: 2.5 w/w of WH: H₂O₂; 1: 5 w/w of WH: CH₃COOH (1 M); 2h of reaction time] maximum 20.2 wt. % FS yield and 15 wt. % isolated lignin (purity 97.6 %) were obtained. Subsequently, the pretreated WH (PWH) was hydrolyzed at optimized conditions [(70⁰C reaction temperature; 7.5wt. % catalyst concentration (1:1 w/w A15: NAT); 1: 30 w/w of WH: water; 30 min reaction time)] in THUVRR to render maximum yield of FS (36.9g/ L) (67.4 wt. %), which was significantly greater than that obtained (20.2g/ L) (38.42 wt. %) employing a conventional thermal reactor (CTR). Besides, the energy consumption was 70% more in CTR (500 W) in comparison with THUVRR (150 W); thus, demonstrating markedly superior energy-efficiency vis-à-vis appreciable improvement in FS yield in THUVRR over CTR. Overall sustainability of the process analyzed by LCA proved the approach to be energy-saving and environmentally benign and is expected to be applicable to similar lignocellulosic agro-wastes.

Introducing hydroxyl groups as cellulose-binding sites into polymeric solid acids to improve their catalytic performance in hydrolyzing cellulose

Effective hydrolysis of cellulose to glucose is a crucial step to produce fuels and chemicals from lignocellulosic biomass. Solid acids are promising alternatives of cellulases and homogenous acids for hydrolyzing cellulose. In this study, porous polymeric solid acids bearing hydroxyl and sulfonic acid groups were fabricated for cellulose hydrolysis in water through the low-cost Friedel-Crafts "knitting" polymerization of hydroxyl-containing aromatic monomers followed by sulfonation. The synthesized bifunctional solid acids could effectively hydrolyze microcrystalline cellulose (Avicel) to glucose by as high as 93 % at 120 °C within 48 h and ball-milled Avicel by 98 % at 120 °C in 24 h. The evidence from this study indicated that the outstanding catalytic performance of the solid acids was attributed to the porous structure (large surface area) and the presence of the hydroxyl (cellulose-binding group) in the solid acids.

Biomass valorization: Sulfated lignin-catalyzed production of 5-hydroxymethylfurfural from fructose

This study is aimed at the investigation of the preparation of sulfated lignin (SL) as a Bronsted acid catalyst for the preparation of 5-hydroxymethylfurfural (5-HMF). SL was characterized by different methods including FT-IR, FESEM, XRD, and EDS analyses. It shows promising results after 60 min of reaction at 140 °C, reaching 100% conversion of fructose precursor and 99% yield of 5-HMF, with a fructose: catalyst mass ratio of 10:6.

Preparation and catalytic performance of biomass-based solid acid catalyst from Pennisetum sinense for cellulose hydrolysis

As a kind of lignocellulosic biomass, Pennisetum sinense (P. sinense) is commonly used as animal feed, fertilizer or papermaking raw materials. Based on the high carbon content and renewability of P. sinense, we explored the possibility and feasibility of using it as catalyst matrix. The catalyst was produced by sulfonation of char obtained from the carbonization of P. sinense at 550 °C. The structure of the catalyst was characterized by SEM, BET, XRD, FT-IR, XPS and TGA, and its catalytic performance for the hydrolysis of cellulose was investigated in detail. The highest acidity of the catalyst was 3.79 mmol/g and the maximum glucose yield of 59.92% was achieved under optimized conditions. The catalyst also showed a promising reusability. The glucose yield was 53.01% after 5 cycles and as high as 55.92% when using the regenerated catalyst.

Synergistic effects of nanocarbon spheres sheathed on a binderless CoMoO4 electrode for high-performance asymmetric supercapacitor

An essential key to enhancing the specific capacity and cyclic stability of transition metal oxide materials is the hybridization of carbon compounds by binder-free methods for supercapacitors. Carbonaceous compounds shorten the electron-ion diffusion pathways due to their high active surface area and conductivity. Herein, we focus on improving the specific energy, stability, and conductivity of the electrode by the incorporation of nanosized carbon material. The integration of nano carbons from viable eco-friendly glucose with CoMoO4 enhanced the experimental specific capacity of the electrode. The self-grown CoMoO4 on a nickel foam (CMO-NF) was confirmed as the best approach after extensive optimization process by the feasible hydrothermal (HT) method. The amount of carbon deposited and the structural morphology on the fabricated CoMoO4-glucose-derived carbon (CMO-GC) electrode was varied by adjusting the concentration of glucose by the viable HT technique. Notably, the hybrid CMO-GC-2 achieved a maximum specific capacity of 851.85 C g-1 at 1 A g-1, and it is relatively higher than that of CMO-NF (301.4 C g-1). The asymmetric supercapacitor device (CMO-GC-2//AC) demonstrated excellent energy density (36.86 W h kg-1 for 152.84 W kg-1), power density (3209.35 W kg-1 for 11.19 W h kg-1), and extensive capacity retention of 87% for up to 5000 cycles. The high performance is related to the synergetic effect of EDLC and the redox reaction, with nano-architecture and well-defined morphology of the electrode material.

Bifunctional carbon Ni/NiO nanofiber catalyst based on 5-sulfosalicylic acid for conversion of C5/C6 carbohydrates into ethyl levulinate

A method was developed for preparing bifunctional carbon Ni/NiO nanofiber catalysts that promote efficient one-pot conversion of C5/C6 carbohydrates into levulinate esters in alcohol solvents.

Enhanced hydrolysis of cellulose by catalytic polyethersulfone membranes with straight-through catalytic channels

The aim of this study was to prepare sulfonated graphene oxide/polyether sulfone (GO-SO₃H/PES) mixed matrix membranes (GPMMMs) with high porosity and straight-through catalytic channels by segregation and used for dynamic and continuous hydrolysis of cellulose. The high porosity and segregation increased the exposure of catalysts synergistically and the formative GO-SO₃H enriched, straight-through catalytic channels had higher catalytic performance, enhancing the diffusion of hydrolytic products. Dynamic hydrolysis of cellulose is more efficient than static hydrolysis due to the enhanced contact between cellulose and catalysts achieved by the extra driving forces, and the further degradation of produced saccharides was suppressed due to the high freedom of products. The TRS reached 98.18% after 1 h at 150 °C with a catalyst/cellulose mass ratio of 1:5. More importantly, the immobilization of GO-SO₃H by PES improved its stability and reusability at high reaction temperature. This strategy provides guidance to the design of high-performance catalytic membranes.

High Yielding Acid-Catalysed Hydrolysis of Cellulosic Polysaccharides and Native Biomass into Low Molecular Weight Sugars in Mixed Ionic Liquid Systems

Ionic media comprising 1‐butyl‐3‐methylimidazolium chloride and the acidic deep eutectic solvent choline chloride/oxalic acid as co‐solvent‐catalyst, very efficiently convert various cellulosic substrates, including native cellulosic biomass, into water‐soluble carbohydrates. The optimum reaction systems yield a narrow range of low molecular weight carbohydrates directly from cellulose, lignocellulose, or algal saccharides, in high yields and selectivities up to 98 %. Cellulose possesses significant potential as a renewable platform from which to generate large volumes of green replacements to many petrochemical products. Within this goal, the production of low molecular weight saccharides from cellulosic substances is the key to success. Native cellulose and lignocellulosic feedstocks are less accessible for such transformations and depolymerisation of polysaccharides remains a primary challenge to be overcome. In this study, we identify the catalytic activity associated with selected deep eutectic solvents that favours the hydrolysis of polysaccharides and develop reaction conditions to improve the outcomes of desirable low molecular weight sugars. We successfully apply the chemistry to raw bulk, non‐pretreated cellulosic substances.

Enhanced Enzymatic Hydrolysis of Corncob by Synthesized Enzyme-Mimetic Magnetic Solid Acid Pretreatment in an Aqueous Phase

A novel magnetic carbon-based solid acid catalyst (C350-Cl) was synthesized through a simple impregnation-carbonization process and used for the pretreatment of corncob in an aqueous medium. Under the optimized pretreatment reaction conditions, the yield of pentose reached 91.6% with a hemicellulose removal rate of 91.7%, and the subsequent enzymatic digestibility of the pretreated corncob residue reached 90.0% at 48 h. C350-Cl is a magnetic enzyme-mimetic solid acid catalyst, and its catalytic behavior is similar to those of enzymes. In addition, the catalyst is also an excellent carrier for Fe and Cl in that the Fe³⁺ and Cl^-can be released slowly in the pretreatment to assist the hydrolysis of lignocellulose. Compared with the traditional method with other catalysts, this hydrolysis process is suitable for the effective and sustainable saccharification of lignocellulose for producing fermentable sugar.

Microwaves in the Catalytic Valorisation of Biomass Derivatives

The application of microwave irradiation in the transformation of biomass has been receiving particular interest in recent years due to the use of polar media in such processes and it is now well-known that for biomass conversion, and particularly for lignocellulose hydrolysis, microwave irradiation can dramatically increase reaction rates with no negative consequences on product selectivity. However, it is only in the last ten years that the utilisation of microwaves has been coupled with catalysis aiming towards valorising biomass components or their derivatives via a range of reactions where high selectivity is required in addition to enhanced conversions. The reduced reaction times and superior yields are particularly attractive as they might facilitate the transition towards flow reactors and intensified production. As a consequence, several reports now describe the catalytic transformation of biomass derivatives via hydrogenation, oxidation, dehydration, esterification and transesterification using microwaves. Clearly, this technology has a huge potential for biomass conversion towards chemicals and fuels and will be an important tool within the biorefinery toolkit. The aim of this chapter is to give the reader an overview of the exciting scientific work carried out to date where microwave reactors and catalysis are combined in the transformation of biomass and its derivatives to higher value molecules and products.

Acid-Catalyzed Conversion of Carbohydrates into Value-Added Small Molecules in Aqueous Media and Ionic Liquids

Biomass is the only realistic major alternative source (to crude oil) of hydrocarbon substrates for the commercial synthesis of bulk and fine chemicals. Within biomass, terrestrial sources are the most accessible, and therein lignocellulosic materials are most abundant. Although lignin shows promise for the delivery of certain types of organic molecules, cellulose is a biopolymer with significant potential for conversion into high-volume and high-value chemicals. This review covers the acid-catalyzed conversion of lower value (poly)carbohydrates into valorized organic building-block chemicals (platform molecules). It focuses on those conversions performed in aqueous media or ionic liquids to provide the reader with a perspective on what can be considered a best case scenario, that is, that the overall process is as sustainable as possible.

Catalytic Transformation of Lignocellulose into Chemicals and Fuel Products in Ionic Liquids

Innovative valorization of naturally abundant and renewable lignocellulosic biomass is of great importance in the pursuit of a sustainable future and biobased economy. Ionic liquids (ILs) as an important kind of green solvents and functional fluids have attracted significant attention for the catalytic transformation of lignocellulosic feedstocks into a diverse range of products. Taking advantage of some unique properties of ILs with different functions, the catalytic transformation processes can be carried out more efficiently and potentially with lower environmental impacts. Also, a new product portfolio may be derived from catalytic systems with ILs as media. This review focuses on the catalytic chemical conversion of lignocellulose and its primary ingredients (i.e., cellulose, hemicellulose, and lignin) into value-added chemicals and fuel products using ILs as the reaction media. An outlook is provided at the end of this review to highlight the challenges and opportunities associated with this interesting and important area.

Black liquor-derived carbonaceous solid acid catalyst for the hydrolysis of pretreated rice straw in ionic liquid

Lignin-containing black liquor from pretreatment of rice straw by KOH aqueous solution was applied to prepare a carbonaceous solid acid catalyst, in which KOH played dual roles of extracting lignin from rice straw and developing porosity of the carbon material as an activation agent. The synthesized black liquor-derived carbon material was applied in catalytic hydrolysis of the residue solid from the pretreatment of rice straw, which was mainly composed of cellulose and hemicellulose, and showed excellent activity for the production of total reducing sugars (TRS) in ionic liquid, 1-butyl-3-methyl imidazolium chloride. The highest TRS yield of 63.4% was achieved at 140°C for 120min, which was much higher than that obtained from crude rice straw under the same reaction conditions (36.6% TRS yield). Overall, this study provides a renewable strategy for the utilization of all components of lignocellulosic biomass.

Far infrared radiated energy-proficient rapid one-pot green hydrolysis of waste watermelon peel: optimization and heterogeneous kinetics of glucose synthesis

Energy-efficient far-infrared radiation rendered significant intensification of one-pot heterogeneous catalytic hydrolysis of waste watermelon peel for green synthesis of glucose.

Spectroscopic tracking of mechanochemical reactivity and modification of a hydrothermal char

A glucose hydrothermal char (HTC) was synthesized and ball milled to break chemical bonds, generate defects, and form new chemical structures.

Effective saccharification of holocellulose over multifunctional sulfonated char with fused ring structures under microwave irradiation

The SC catalysts, bearing multifunctional groups in graphene-like fused ring structure, exhibit remarkable catalytic performance on saccharification of holocellulose.

One pot synthesis of CeO2 nanoparticles on a carbon surface for the practical determination of paracetamol content in real samples

Sucrose derived carbon decorated with CeO₂ nanoparticles (CeO₂–C) was prepared using a one pot synthesis and used for the electrochemical sensing of paracetamol.

Hydrolysis of cellulose catalyzed by quaternary ammonium perrhenates in 1-allyl-3-methylimidazolium chloride

Quaternary ammonium perrhenates were applied as catalyst to promote the hydrolysis of cellulose in 1-allyl-3-methylimidazolium chloride ([Amim]Cl). The quaternary ammonium perrhenates displayed good catalytic performance for cellulose hydrolysis. Water was also proven to be effective to promote cellulose hydrolysis. Accordingly, 97% of total reduced sugar (TRS) and 42% of glucose yields could be obtained under the condition of using 5mol% of tetramethyl ammonium perrhenate as catalyst, 70μL of water, ca. 0.6mmol of microcrystalline cellulose (MCC) and 2.0g of [Amim]Cl as solvent under microwave irradiation for 30min at 150°C (optimal conditions). The influence of quaternary ammonium cation on the efficiency of cellulose hydrolysis was examined based on different cation structures of perrhenates. The mechanism on perrhenate catalyzed cellulose hydrolysis is also discussed, whereas hydrogen bonding between ReO4 anion and hydroxyl groups of cellulose is assumed to be the key step for depolymerization of cellulose.

Hydrolysis of ionic cellulose to glucose

Hydrolysis of ionic cellulose (IC), 1,3-dimethylimidazolium cellulose phosphite, which could be synthesized from cellulose and dimethylimidazolium methylphosphite ([Dmim][(OCH3)(H)PO2]) ionic liquid, was conducted for the synthesis of glucose. The reaction without catalysts at 150°C for 12h produced glucose with 14.6% yield. To increase the hydrolysis yield, various acid catalysts were used, in which the sulfonated active carbon (AC-SO3H) performed the best catalytic activity in the IC hydrolysis. In the presence of AC-SO3H, the yields of glucose reached 42.4% and 53.9% at the reaction condition of 150°C for 12h and 180°C for 1.5h, respectively; however the yield decreased with longer reaction time due to the degradation of glucose. Consecutive catalyst reuse experiments on the IC hydrolysis demonstrated the catalytic activity of AC-SO3H persisted at least through four successive uses.