Effect of nitrogen source on growth and lipid accumulation in Scenedesmus abundans and Chlorella ellipsoidea

Synthesis and utilization of biomass-derived sulfonated heterogeneous catalyst-BT-SO3H for microalgal biodiesel production

The study investigates the potential of utilizing banana trunk-derived porous activated biochar enriched with SO3H- as a catalyst for eco-friendly biodiesel production from the microalga Chlorella vulgaris. An extensive analysis, employing advanced techniques such as XRD, FTIR, TGA, XPS, NH3-TPD, BET, SEM-EDX, and TEM, was conducted to elucidate the physicochemical properties of BT-SO3H catalysts. The synthesized catalyst demonstrated its efficiency in converting the total lipids of Chlorella vulgaris into biodiesel, with varying concentrations of 3%, 5%, and 7%. Notably, using a 5% BT-SO3H concentration resulted in remarkably higher biodiesel production about 58.29%. Additionally, the fatty acid profile of C. vulgaris biodiesel indicated that C16:0 was the predominant fatty acid at 24.31%, followed by C18:1 (19.68%), C18:3 (11.45%), and C16:1 (7.56%). Furthermore, the biodiesel produced via 5% BT-SO3H was estimated to have higher levels of saturated fatty acids (SFAs) at 34.28%, monounsaturated fatty acids (MUFAs) at 30.70%, and polyunsaturated fatty acids (PUFAs) at 24.24%. These findings highlight the promising potential of BT-SO3H catalysts for efficient and environmentally friendly biodiesel production from microalgal species.

Effects of polyethylene terephthalate microplastics on cell growth, intracellular products and oxidative stress of Scenedesmus sp

Polyethylene terephthalate (PET) has been widely utilized in the synthesis of textile materials and packaging of foods and beverages. In recent years, it has been commonly detected in the form of microplastics (MPs) in wastewater. However, the effects of PET MPs on microalgal intracellular products and their interrelationships have been poorly investigated. In this study, the microalgae Scenedesmus sp. Strain H-1 was exposed to PET MPs to explore their effects on the growth, intracellular products (such as lipids, carbohydrates, and proteins), and antioxidative defense systems of Scenedesmus sp. The results demonstrated that PET MPs significantly reduced Scenedesmus sp. cell growth, with a maximum inhibition rate of 38.25% in the 500 mg L-1 treatment group. PET MPs had negative effects on glucose and nitrate utilization rates and reduced intracellular carbohydrates, intracellular proteins, and photosynthetic pigments. Surprisingly, PET MPs reduced acetyl-CoA carboxylase activity but induced lipid accumulation in microalgae. In addition, PET MPs significantly decreased the essential linoleic acid concentration and increased the palmitic acid content, resulting in reduced biodiesel quality. PET MPs induced the production of reactive oxygen species and malondialdehyde as well as the activities of superoxide dismutase and catalase. The results of the PCA indicated that the response mechanism of Scenedesmus sp. to PET MPs exposure was synergistic. This study provides fundamental data on the impact of MPs on the intracellular products of microalgae.

Enhancing microalgal lipid accumulation for biofuel production

Microalgae have high lipid accumulation capacity, high growth rate and high photosynthetic efficiency which are considered as one of the most promising alternative sustainable feedstocks for producing lipid-based biofuels. However, commercialization feasibility of microalgal biofuel production is still conditioned to the high production cost. Enhancement of lipid accumulation in microalgae play a significant role in boosting the economics of biofuel production based on microalgal lipid. The major challenge of enhancing microalgal lipid accumulation lies in overcoming the trade-off between microalgal cell growth and lipid accumulation. Substantial approaches including genetic modifications of microalgal strains by metabolic engineering and process regulations of microalgae cultivation by integrating multiple optimization strategies widely applied in industrial microbiology have been investigated. In the present review, we critically discuss recent trends in the application of multiple molecular strategies to construct high performance microalgal strains by metabolic engineering and synergistic strategies of process optimization and stress operation to enhance microalgal lipid accumulation for biofuel production. Additionally, this review aims to emphasize the opportunities and challenges regarding scaled application of the strategic integration and its viability to make microalgal biofuel production a commercial reality in the near future.

Factors Influencing the Production of Extracellular Polysaccharides by the Green Algae Dictyosphaerium chlorelloides and Their Isolation, Purification, and Composition

The freshwater green microalgae, Dictyosphaerium chlorelloides (CCALA 330), has the ability to produce extracellular polysaccharides (EPS). Conditions for optimum growth and EPS overproduction were determined in laboratory-scale tubular photobioreactors (PBR) with a working volume of 300 mL. Multiple limitations in nutrient supply were proven to be an effective method for EPS overproduction. Salinity stress was also applied to the culture, but no significant increase in EPS production was observed. The effects of different nitrogen sources were examined and the microalgae exhibited the fastest growth and EPS production in medium containing ammonium nitrate. Under determined optimal conditions, EPS concentration reached 10 g/L (71% of the total biomass) and a total biomass of 14 g/L at the end of 17 days cultivation. Pilot-scale cultivation was also carried out in a column type airlift photobioreactor (PBR) with a working volume of 60 L. A new and efficient methodology was developed for separating cells from the EPS-containing culture broth. Due to the strong attachment between cells and EPS, high-pressure homogenization was carried out before a centrifugation process. The EPS in the supernatant was subsequently purified using ultrafiltration. The green microalgae Dictyosphaerium chlorelloides may therefore be appropriate for the commercial production of EPS.

Statistical optimization for simultaneous removal of methyl red and production of fatty acid methyl esters using fresh alga Scenedesmus obliquus

Microalgae are a diverse group of microorganisms, the majority of which are photosynthetic in nature. Microalgae have different applications, the most important of which is the biological treatment of wastewater. Microalgae grow in various types of wastewater, such as wastewater polluted by Azo dyes, due to microalgae using wastewater as a culture medium, which contains many nutrients like nitrogen, phosphate, and carbon sources. Microalgae grow in various types of wastewater, such as wastewater polluted by Azo dyes, due to microalgae using wastewater as a culture medium, which contains many nutrients like nitrogen, phosphate, and carbon sources. So, microalgae are used for bioremediation of wastewater due to the efficiency of growing in wastewater and for the high production of lipids followed by trans-esterification to biodiesel. Face-centered central composite design (FCCCD) was used to determine the factors that have the most significant impact on the simultaneous decolorization of methyl red and lipid production by the fresh green alga Scenedesmus obliquus. The predicted results indicated that the alga decolorized 70.15% methyl red and produced 20.91% lipids by using 1 g/L nitrogen, an incubation time of 10 days, a pH of 8, and the concentration of methyl red is 17.65 mg/L. The dry biomasses of S. obliquus were also examined by SEM and FTIR before and after treatment with methyl red. SEM and FTIR showed that the properties of dry S. obliquus were altered after the biosorption of methyl red. According to GC-MS analysis of hexane extracts of S. obliquus, the lipid profile differed before and after methyl red decolorization. The results proved that it is possible to use S. obliquus to remove dyes and produce renewable fuels such as biodiesel. The novelty of this study is that this is the first time in which the effect of nitrogen concentrations in the medium used for algal growth on the removal of dye has been studied.

Optimising nutrients in the culture medium of Rhodosporidium toruloides enhances lipids production

Rhodosporidium toruloides is a useful oleaginous yeast, but lipids production is affected by various factors including nutrients in the culture medium. Herein, the R-ZL2 high-yield mutant strain was used to investigate the effects of different carbon sources (sucrose, glucose, xylose), nitrogen sources (ammonium sulphate, ammonium nitrate), and C/N ratio on lipids production capacity, get the following conclusion (1) Compared with glucose and xylose, sucrose was a superior carbon source for lipids production; (2) When using ammonium sulphate as the nitrogen source, a C/N ratio of 200:1 achieved the highest biomass, lipids production and lipids content (10.7 g/L, 6.32 g/L and 59%, respectively), and lipids produced under different C/N conditions have potential for biodiesel production (except for C/N = 40 and C/N = 80); (3) When using ammonium nitrate as the nitrogen source, a C/N ratio of 200:1 achieved the highest biomass, lipids production and lipids content (12.1 g/L, 8.25 g/L and 65%, respectively), and lipids produced under different C/N ratio conditions have potential for biodiesel production. Thus, a combination of sucrose and ammonium nitrate was optimal for the lipid accumulation in R-ZL2. The findings will lay a foundation for further improving lipids yields.

Effect of nitrate feeding strategies on lipid and biomass productivities in fed-batch cultures of Nannochloropsis gaditana

Controlled nitrate feeding strategies for fed-batch cultures of microalgae were applied for the enhancement of lipid production and microalgal growth rates. In particular, in this study, the effect of nitrate feeding rates on lipid and biomass productivities in fed-batch cultures of Nannochloropsis gaditana were investigated using three feeding modes (i.e., pulse, continuous, and staged) and under two light variations on both lipid productivity and fatty acid compositions. Higher nitrate levels negatively affected lipid production in the study. Increasing the light intensity increased the lipid contents of the microalgae in all three fed-batch feeding modes. A maximum of 58.3% lipid- to dry weight ratio was achieved when using pulse-fed cultures at an illumination of 200 μmol photons m^-2 s^-1 and 10 mg/day of nitrate feeding. This condition also resulted in the maximum lipid productivity of 44.6 mg L^-1 day^-1 . The fatty acid compositions of the lipids consisted predominantly of long-chain fatty acids (C:16 and C:18) and accounted for 70% of the overall fatty acid methyl esters. Pulse feeding mode was found to significantly enhance the biomass and lipid production. The other two feeding modes (continuous and staged) were not ideal for lipid and biomass production. This study demonstrates the applicability of pulse feeding strategies in fed-batch cultures as an appropriate cultivation strategy that can increase both lipid accumulation and biomass production.

Effect of Drying Methods on Lutein Content and Recovery by Supercritical Extraction from the Microalga Muriellopsis sp. (MCH35) Cultivated in the Arid North of Chile

In this study, we determined the effect of drying on extraction kinetics, yield, and lutein content and recovery of the microalga Muriellopsis sp. (MCH35) using the supercritical fluid extraction (SFE) process. The strain was cultivated in an open-raceways reactor in the presence of seawater culture media and arid outdoor conditions in the north of Chile. Spray-drying (SD) and freeze-drying (FD) techniques were used for dehydrating the microalgal biomass. Extraction experiments were performed by using Box-Behnken designs, and the parameters were studied: pressure (30–50 MPa), temperature (40–70 °C), and co-solvent (0–30% ethanol), with a CO₂ flow rate of 3.62 g/min for 60 min. Spline linear model was applied in the central point of the experimental design to obtain an overall extraction curve and to reveal extraction kinetics involved in the SFE process. A significant increase in all variables was observed when the level of ethanol (15–30% v/v) was increased. However, temperature and pressure were non-significant parameters in the SFE process. The FD method showed an increase in lutein content and recovery by 0.3–2.5-fold more than the SD method. Overall, Muriellopsis sp. (MCH35) is a potential candidate for cost-effective lutein production, especially in desert areas and for different biotechnological applications.

BIOTECHNOLOGICAL POTENTIAL OF PSEUDOKIRCHNERIELLA SUBCAPITATA, SCENEDESMUS SPINOSUS, AND SCENEDESMUS ACUMINATUS

Microalgae are promising alternatives to sequestration of carbon and reduction of environmental problems, e.g. the greenhouse effect and industrial water pollution. Depending on the growth conditions, microalgae can differ in their metabolism products, leading them to grow at different rates. Intracellular reactions and nutritional requirements from cell metabolism, as well as biomass composition, may vary in function of the temperature. In this study, the biotechnological potential of three microalgae strains from the species was evaluated in terms of growth, biomass composition, fatty acid profile, and chlorophyll and carotenoids contents. Each of the three species demonstrated different potential depending on their metabolisms: Scenedesmus spinosus presented fastest growth and had the highest protein content (52.99%), Pseudokirchneriella subcapitata presented the highest content of lipid extracted (26.51%), and Scenedesmus acuminatus showed increased production of chlorophyll (5.25 mg l–1) and carotenoid (1.02 mg l–1) pigments.

Factors Affecting Microalgae Production for Biofuels and the Potentials of Chemometric Methods in Assessing and Optimizing Productivity

Microalgae are swift replicating photosynthetic microorganisms with several applications for food, chemicals, medicine and fuel. Microalgae have been identified to be suitable for biofuels production, due to their high lipid contents. Microalgae-based biofuels have the potential to meet the increasing energy demands and reduce greenhouse gas (GHG) emissions. However, the present state of technology does not economically support sustainable large-scale production. The biofuel production process comprises the upstream and downstream processing phases, with several uncertainties involved. This review examines the various production and processing stages, and considers the use of chemometric methods in identifying and understanding relationships from measured study parameters via statistical methods, across microalgae production stages. This approach enables collection of relevant information for system performance assessment. The principal benefit of such analysis is the identification of the key contributing factors, useful for decision makers to improve system design, operation and process economics. Chemometrics proffers options for time saving in data analysis, as well as efficient process optimization, which could be relevant for the continuous growth of the microalgae industry.

Concomitant production of fatty acid methyl ester (biodiesel) and exopolysaccharides using efficient harvesting technology in flat panel photobioreactor with special sparging system via Scenedesmus abundans

Current study focusses on the concomitant production of fatty acid methyl ester (FAME, biodiesel) and exopolysaccharides (EPS) from Scenedesmus abundans cell factory in flat panel photobioreactor using cost effective harvesting strategy. Parallel mini and medium scale flat panel photobioreactors (PBRs) with special gas sparging system enabling high gas to liquid mass transfer and efficient mixing were designed. Biomass titer of 6.9 g/l with overall biomass productivity of 1.2 g/l/day was achieved with constant high light intensity of 2162 µE/m²/s in growth phase (134 h) using optimum nutrient concentration. FAME concentration of 1.53 g/l was achieved after 15 days of nitrogen deprivation condition with productivity of 67 mg/l/day. The EPS production of 236 mg/l with a yield of 37 mg/g biomass was achieved. The strain proved its capability to produce multiproducts simultaneously in a single stage PBR by natural autoflocculation harvesting technology.

Simultaneous nutrition removal and high-efficiency biomass and lipid accumulation by microalgae using anaerobic digested effluent from cattle manure combined with municipal wastewater

BACKGROUND

Microalgae as a viable biodiesel feedstock show great potential to approach the challenges of energy shortage and environment pollution, but their economic feasibility was seriously hampered by high production cost. Thus, it is in urgent need to reduce the cost of cultivation and improve the biomass and lipid production of microalgae. In this work, anaerobic digestion effluent from cattle manure combined with municipal wastewater was used as a cost-effective medium for cultivating microalgae and expected to obtain high biomass. The pretreatment of anaerobic digested effluent containing dilution rate, sterilization and nutrient optimization was investigated. Then, initial pH and light intensity for algal growth, lipid production and wastewater purification were optimized in this study.

RESULTS

Scenedesmus sp. could grow rapidly in 10% anaerobic digestion effluent from cattle manure combined with secondary sedimentation tank effluent without sterilization. Optimum nutrient additives for higher biomass were as follows: glucose 10 g/L, NaNO₃ 0.3 g/L, K₂HPO₄·3H₂O 0.01 g/L, MgSO₄·7H₂O 0.075 g/L and trace element A5 solution 1 mL/L. Biomass of 4.65 g/L and lipid productivity of 81.90 mg/L/day were achieved during 7-day cultivation accompanying over 90% of COD, NO₃ ^--N, NH₄ ⁺-N, and 79-88% of PO₄ ^3--P removal with optimized initial pH of 7.0 and light intensity of 5000 l×. The FAME profile in ADEC growth medium consisted in saturated (39.48%) and monounsaturated (60.52%) fatty acids with the 16- to 18-chain-length fatty acids constituting over 98% of total FAME.

CONCLUSIONS

This study proves the potential of anaerobic digested effluent combined with municipal wastewater for microalgae culture, and provides an effective avenue for simultaneous microalgal lipid production and treatment of two kinds of wastewater.

Mixotrophic cultivation of microalgae to enhance the quality of lipid for biodiesel application: effects of scale of cultivation and light spectrum on reduction of α-linolenic acid

The research on microalgal biodiesel is focused not only on getting the highest lipid productivity but also desired quality of lipid. The experiments were initially conducted on flask scale (1L) using acetate carbon source at different concentrations viz. 0.5, 2, 3 and 4 g L^-1. The optimum concentration of acetate was considered for further experiments in two airlift photobioreactors (10 L) equipped separately with red and white LED lights. The Feasibility Index (FI) was derived to analyze the scalability of mixotrophic cultivation based on net carbon fixation in biomass per consumption of total organic carbon. The experimental strategy under mixotrophic mode of cultivation lowered the α-linolenic acid content of lipid by 60-80% as compared to autotrophic cultivation for Scenedesmus abundans species and yielded the highest biomass and lipid productivities, 59 ± 2 and 17 ± 1.8 mg L^-1 day^-1, respectively. The TOC, nitrate, and phosphate reduction rates were 74.6 ± 3.0, 11.5 ± 1.4, 9.6 ± 2.4 mg L^-1 day^-1, respectively. The significant change was observed in lipid compositions due to the scale, mode of cultivation, and light spectra. As compared to phototrophic cultivation, biodiesel obtained under mixotrophic cultivation only met standard biodiesel properties. The FI data showed that the mixotrophic cultivation was feasible on moderate concentrations of acetate (2-3 g L^-1).

Growth kinetics, fatty acid composition and metabolic activity changes of Crypthecodinium cohnii under different nitrogen source and concentration

The effect of varying concentrations of the nitrogen source on the growth kinetics, lipid accumulation, lipid and DHA productivity, and fatty acid composition of C. cohnii was elucidated. Growth of C. cohnii was in three distinct growth stages: cell growth, lipid accumulation and a final lipid turnover stage. Most of lipids were accumulated in lipid accumulation stage (48-120 h) though, slow growth rate was observed during this stage. NaNO₃ supported significantly higher lipid content (26.9% of DCW), DHA content (0.99 g/L) and DHA yield (44.2 mg/g glucose) which were 2.5 to 3.3-folds higher than other N-sources. The maximum level of C16-C18 content (% TFA) was calculated as 43, 54 and 43% in lipid accumulation stage under low nitrogen (LN, 0.2 g/L), medium nitrogen (MN, 0.8 g/L) and high nitrogen (HN, 1.6 g/L) treatments, respectively. Cultures with LN, by down-regulating cell metabolism, trigger onset of lipogenic enzymes. Conversely, NAD⁺/NADP⁺-dependent isocitrate dehydrogenase (NAD⁺/NADP⁺-ICDH) were less active in LN than HN treatments which resulted in retardation of Kreb's Cycle and thereby divert citrate into cytoplasm as substrate for ATP-citrate lyase (ACL). Thereby, ACL and fatty acid synthase (FAS) were most active in lipid accumulation stage at LN treatments. Glucose-6-phosphate dehydrogenase (G6PDH) was more active than malic enzyme (ME) in lipid accumulation stage and showed higher activities in NaNO₃ than other N-sources. This represents that G6PDH contributes more NADPH than ME in C. cohnii. However, G6PDH and ME together seems to play a dual role in offering NADPH for lipid biosynthesis. This concept of ME together with G6PD in offering NADPH for lipogenesis might be novel in this alga and needed to be explored.

Biosynthesis of high yield fatty acids from Chlorella vulgaris NIES-227 under nitrogen starvation stress during heterotrophic cultivation

In this study the heterotrophic cultivation of Chlorella vulgaris NIES-227 fed with glucose was investigated systematically using six media types; combinations of nitrogen repletion/depletion and phosphorus repletion/limitation/depletion. It was found that a high yield of fatty acids (0.88 of fed glucose-COD) and a high content of fatty acid methyl esters (FAMEs) (89% of dry weight) were obtained under nitrogen starved conditions. To our knowledge it is the first report on such high COD conversion yield and FAME content in microalgae. The dominant fatty acid (>50%) was methyl oleate (C18:1), a desirable component for biodiesel synthesis. FAME content under nitrogen starved conditions was significantly higher than under nitrogen sufficient conditions, while phosphorus had no significant influence, indicating that nitrogen starvation was the real "fatty acids trigger" in heterotrophic cultivation. These findings could simplify the downstream extraction process, such as the extrusion of oil from soybeans, and could reduce operating costs by improving the fatty acid yield from waste COD.