Improving enzymatic hydrolysis of lignocellulosic substrates with pre-hydrolysates by adding cetyltrimethylammonium bromide to neutralize lignosulfonate

A novel cetyltrimethylammonium bromide-based deep eutectic solvent pretreatment of rice husk to efficiently enhance its enzymatic hydrolysis

Deep eutectic solvent (DES) has caught widely attention of researchers in biomass pretreatment. As a highly efficient surfactant, cetyltrimethylammonium bromide (CTAB) was expected to be used for synthesizing new DESs with additional functions in pretreatment. In this work, an efficient pretreatment method using a mixture of CTAB and lactic acid (LA) as a novel functional DES was established to improve enzymatic digestion efficiency of rice husk (RH). The results showed that DES CTAB:LA effectively removed lignin (51.5%) and xylan (79.9%) and the enzymatic hydrolysis activity of CTAB:LA-treated RH was 5 times that of RH. Then, a series of characterization demonstrated that a substantial accessibility increased, a hydrophobicity and lignin surface area decreased, and great surface morphology alternation were observed on the treated RH, which explained the increase in enzymatic hydrolysis efficiency. Overall, the discovery of more functional DESs might be motivated and biorefinery pretreatment processes might be greatly promoted.

Significantly enhanced enzymatic hydrolysis of waste rice hull through a novel surfactant-based deep eutectic solvent pretreatment

The potential of green solvents, specifically deep eutectic solvents (DESs), has piqued the interest of researchers in the field of lignocellulose pretreatment. To enhance the enzymatic digestion efficiency of waste rice hull (RCH), an effective pretreatment approach was developed using the DES [AA][CATB], which was made with acetic acid (AA) and cetyltrimethylammonium bromide (CTAB). The results showed that [AA][CATB] improved enzymatic saccharification by 3.7 times compared to raw RCH and efficiently eliminated lignin (38.7%) and removed xylan (42.9%). The improvement in enzymatic hydrolysis efficiency was then interpreted by a series of characterizations that showed a great morphological changed RCH with an obvious accessibility increase and a lignin surface area and hydrophobicity reduction. This work demonstrates that functional, and easily recoverable DESs have potential for improving the efficiency of lignocellulose pretreatment in biorefineries, providing a promising approach for developing green solvents and achieving more sustainable and efficient biorefinery processes.

Alleviating Nonproductive Adsorption of Lignin on CBM through the Addition of Cationic Additives for Lignocellulosic Hydrolysis

The nonproductive adsorption of cellulase onto lignin significantly inhibited the enzymatic hydrolysis of lignocellulosic biomass. In this study, we constructed a rapid fluorescence detection (RFD) system, and using this system, we demonstrated that the addition of cationic additives DTAB or polyDADMAC greatly increased the partition coefficients of cellulose/lignin, reduced nonproductive adsorption, and enhanced the hydrolysis efficiency of lignocellulose compared to those of Tweens or PEGs. Moreover, the addition of polyDADMAC and DTAB increased the glucose yield released from the mixture of Avicel and AICS-lignin (MCL) by 16.9 and 20.6%, respectively, and reduced the inhibition rate of lignin by 16.9 and 20.7%, respectively. Interestingly, polyDADMAC or DTAB treatment performed more effectively for the enzymatic hydrolysis of pretreated lignocellulosic biomass, compared with MCL. We confirmed that the reduced hydrophobicity and increased zeta potential of lignin cocontribute to the dampening nonproductive adsorption of lignin. In particular, the zeta potential values of lignin and the partition coefficients of Avicel/lignin with the addition of additives showed a good correlation, suggesting that electrostatic force also plays a crucial role in the adsorbing of cellulase on lignin. This work will be conducive to decreasing the nonproductive binding of cellulase onto lignin and enhancing cellulose conversion.

Polystyrene sulfonate is effective for enhancing biomass enzymatic saccharification under green liquor pretreatment in bioenergy poplar

BACKGROUND

Water-soluble lignin (particularly lignosulfonate, LS) has been well documented for its significance on enzymatic saccharification of lignocellulose, though the promotion mechanism has not been fully understood. Much attention has been paid to natural lignin or its derivatives. The disadvantage of using natural lignin-based polymers as promoting agents lies in the difficulty in tailor-incorporating functional groups due to their complex 3D structures. To further improve our understanding on the promotion mechanism of water-soluble lignin in the bioconversion of lignocellulose and to pursue better alternatives with different skeleton structures other than natural lignin, herein we reported a synthetic soluble linear aromatic polymer, sodium polystyrene sulfonate (PSS), to mimic LS for enhancing the efficiency of enzymatic saccharification.

RESULTS

The role of PSS in enzymatic saccharification of pure cellulose and green liquor-pretreated poplar (GL-P) was explored by analyzing substrate enzymatic digestibility (SED) under different addition dosages and various pH media, along with LS for comparison. At the cellulase loading of 13.3 FPU/g-glucan, the glucose yield of GL-P increased from 53% for the control to 81.5% with PSS addition of 0.1 g/g-substrate. It outperformed LS with the addition of 0.2 g/g-substrate by 6.3%. In the pH range from 4.5 to 6, PSS showed a positive effect on lignocellulose saccharification with the optimum pH at 4.8, where the most pronounced SED of GL-P was achieved. The underlying mechanism was unveiled by measuring zeta potential and using Quartz Crystal Microbalance (QCM) and Multi-parametric Surface Plasmon Resonance (MP-SPR). The results confirmed that the complexes of cellulase and PSS were conjugated and the negatively supercharged complexes reduced non-productive binding effectively along with the improved saccharification efficiency. The thickness of PSS required to block the binding sites of cellulase film was less than half of that of LS, and the PSS adlayer on cellulase film is also more hydrated and with a much lower shear modulus than LS adlayer.

CONCLUSIONS

PSS as LS analogue is effective for enhancing the biomass enzymatic saccharification of GL-pretreated poplar. PSS exhibited a severer inhibition on the enzymatic saccharification of pure cellulose, while a more positive effect on bioconversion of lignocellulose (GL-P) than LS. In addition, a much lower dosage is required by PSS. The dynamic enzymatic hydrolysis indicated PSS could prolong the processive activity of cellulase. The valid data stemmed from QCM and SPR expressed that PSS bound to cellulases and the as-formed complexes reduced the non-productive adsorption of cellulase onto substrate lignin more efficiently than LS due to its flexible skeleton and highly hydrated structure. Therefore, PSS is a promising alternative promoting agent for lignocellulose saccharification. From another perspective, the synthetic lignin mimics with controllable structures enable us to reach an in-depth understanding of the promotion mechanism of soluble lignins on enzymatic saccharification.

Current understanding and optimization strategies for efficient lignin-enzyme interaction: A review

From energy perspective, with abundant polysaccharides (45-85%), the renewable lignocellulosic is recognized as the 2nd generation feedstock for bioethanol and bio-based products production. Enzymatic hydrolysis is a critical pathway to yield fermentable monosaccharides from pretreated substrates of lignocellulose. Nevertheless, the lignin presence in lignocellulosic substrates leads to the low substrate enzymatic digestibility ascribed to the nonproductive adsorption. It has been reported that the water-soluble lignin (low molecular weight, sulfonated/sulfomethylated and graft polymer) enhance the rate of enzymatic digestibility, however, the catalytic mechanism of lignin-enzyme interaction remains elusive. In this review, optimization strategies for enzymatic hydrolysis based on the lignin structural modification, enzyme engineering, and different additives are critically reviewed. Lignin-enzyme interaction mechanism is also discussed (lignin and various cellulases). In addition, the mathematical models and simulation of lignin, cellulose and enzyme aims for promoting an integrated biomass-conversion process for sustainable production of value-added biofuels.

Combination of aqueous two-phase flotation and inverse transition cycling: Strategies for separation and purification of recombinant β-glucosidase from cell lysis solution

This work was developed to solve the problems of the restriction of non-specific adsorption and time-dependent denaturation in the purification of recombinant proteins by multistage chromatographic procedures. A novel purification method (ATPF-ITC) which combining aqueous two-phase flotation (ATPF) with inverse transition cycling (ITC) was established and used to efficiently purify recombinant β-glucosidase (GLEGB) from cell lysis solution. First, GLEGB would preferentially adsorb on the nitrogen bubble interface relied on the hydrophobic property of the graphene-binding (GB) tag and enter into the top phase of ATPF. Second, GLEGB was achieved further purification by one-round ITC method based on the thermosensitive of the elastin-like polypeptide (ELP) tag. Consequently, the enzymatic activity recovery of GLEGB was 124.92% ± 0.83%, and the purification factor reached 24.26 ± 0.22. The purification results remained stable after six polymer cycles, and the process of ATPF-ITC had no negative effect on the structure of recombinant protein.

Exploring why sodium lignosulfonate influenced enzymatic hydrolysis efficiency of cellulose from the perspective of substrate-enzyme adsorption

BACKGROUND

Cellulase adsorbed on cellulose is productive and helpful to produce reducing sugars in enzymatic hydrolysis of lignocellulose; however, cellulase adsorbed on lignin is non-productive. Increasing productive adsorption of cellulase on cellulose would be beneficial in improving enzymatic hydrolysis. Adding lignin that was more hydrophilic in hydrolysis system could increase productive adsorption and promote hydrolysis. However, the effect mechanism is still worth exploring further. In this study, lignosulfonate (LS), a type of hydrophilic lignin, was used to study its effect on cellulosic hydrolysis.

RESULTS

The effect of LS on the enzymatic hydrolysis of pure cellulose (Avicel) and lignocellulose [dilute acid (DA) treated sugarcane bagasse (SCB)] was investigated by analyzing enzymatic hydrolysis efficiency, productive and non-productive cellulase adsorptions, zeta potential and particle size distribution of substrates. The result showed that after adding LS, the productive cellulase adsorption on Avicel reduced. Adding LS to Avicel suspension could form the Avicel-LS complexes. The particles were charged more negatively and the average particle size was smaller than Avicel before adding LS. In addition, adding LS to cellulase solution formed the LS-cellulase complexes. For DA-SCB, adding LS decreased the non-productive cellulase adsorption on DA-SCB from 3.92 to 2.99 mg/g lignin and increased the productive adsorption of cellulase on DA-SCB from 2.00 to 3.44 mg/g cellulose. Besides, the addition of LS promoted the formation of LS-lignin complexes and LS-cellulase complexes, and the complexes had more negative charges and smaller average sizes than DA-SCB lignin and cellulase particles before adding LS.

CONCLUSIONS

In this study, LS inhibited Avicel's hydrolysis, but enhanced DA-SCB's hydrolysis. This stemmed from the fact that LS could bind cellulase and Avicel, and occupied the binding sites of cellulase and Avicel. Thus, a decreased productive adsorption of cellulase on Avicel arose. Regarding DA-SCB, adding LS, which enhanced hydrolysis efficiency of DA-SCB, increased the electrostatic repulsion between DA-SCB lignin and cellulase, and therefore, decreased non-productive adsorption of cellulase on DA-SCB lignin and enhanced productive adsorption of cellulase on DA-SCB cellulose.

Low-temperature sodium hydroxide pretreatment for ethanol production from sugarcane bagasse without washing process

A low-temperature sodium hydroxide (NaOH) pretreatment for sugarcane bagasse (SCB) was obtained via the surface response design in this study. However, a large quantity of water consumption and wastewater generation which have been the common problems for alkaline pretreatment of lignocellulose still exists in this pretreatment. In order to reduce water consumption and wastewater generation, this study attempted to perform enzymatic hydrolysis and fermentation of NaOH-treated SCB without washing process. It showed that after pretreatment and solid-liquid separation, NaOH-treated SCB could be directly hydrolysed by cellulase via pH and solid-liquid adjustment without washing steps, and the maximum enzymatic hydrolysis efficiency could reach to 70.2%. A domesticated Saccharomyces cerevisiae Y2034 which can endure 6-times diluted BL was obtained, and realized 67.5% ethanol yield from the enzymatic hydrolysate of unwashed NaOH-treated SCB. It provided a clue for converting NaOH-treated lignocellulose to ethanol at low water consumption and wastewater generation.

Effect of the isoelectric point of pH-responsive lignin-based amphoteric surfactant on the enzymatic hydrolysis of lignocellulose

The isoelectric point (pI) of lignin-based surfactant is an important factor in the enhancement on the enzymatic hydrolysis of lignocellulose. In this work, lignin carboxylate (LC) and quaternary ammonium lignin carboxylates (LCQ-x, x%: the mass ratio of quaternizing agent to enzymatic hydrolysis lignin) with different isoelectric points were synthesized. LC or LCQ-x with pI significantly lower or higher than 4.8 reduced the non-productive adsorption of cellulase on lignin, but for the significant inhibitory effect on cellulase activity, their enhancements on the enzymatic hydrolysis of lignocellulose were not remarkable. However, LCQ-x with pI around 4.8 preserved the cellulase activity, and significantly reduced the non-productive adsorption of cellulase, therefore remarkably enhanced the enzymatic hydrolysis. 2 g/L LC, LCQ-40 (pI = 5.0) and LCQ-100 (pI = 9.2) increased the enzymatic digestibility of pretreated eucalyptus from 35.2% to 53.4%, 95.3% and 60.4% respectively. In addition, for the excellent pH-response performance, LCQ could be efficiently recovered after enzymatic saccharification.

Enhancement and Mechanism of a Lignin Amphoteric Surfactant on the Production of Cellulosic Ethanol from a High-Solid Corncob Residue

A lignin amphoteric surfactant and betaine could enhance the enzymatic hydrolysis of lignocellulose and recover cellulase. The effects of lignosulfonate quaternary ammonium salt (SLQA) and dodecyl dimethyl betaine (BS12) on enzymatic hydrolysis digestibility, ethanol yield, yeast cell viability, and other properties of high-solid enzymatic hydrolysis and fermentation of a corncob residue were studied in this research. The results suggested that SLQA and 1 g/L BS12 effectively improved the ethanol yield through enhancing enzymatic hydrolysis. SLQA had no significant effect on the yeast cell membrane and glucose fermentation. However, 5 g/L BS12 reduced the ethanol yield as a result of the fact that 5 g/L BS12 damaged the yeast cell membrane and inhibited the conversion of glucose to ethanol. Our research also suggested that 1 g/L BS12 enhanced the ethanol yield of corncob residue fermentation, which was attributed to the fact that lignin in the corncob adsorbed BS12 and decreased its concentration in solution to a safe level for the yeast.

Dissecting the effect of polyethylene glycol on the enzymatic hydrolysis of diverse lignocellulose

Natural lignocellulose is used as raw material to produce chemicals through biological transformation. The accessibility of cellulase to substrate was also one of the limiting factors of industrial production. Polyethylene glycol (PEG) can be used as additive in enzymatic hydrolysis of lignocellulose. In this study, enzymatic activity on simultaneous or non-simultaneous addition of PEG 4000 was investigated, and the partly delignified rice straw, the rice straw and filter paper were used as substrates, respectively. Enzyme activity was characterized by reducing sugar concentration in supernatant which was quantified through 3,5-dinitrosalicylic acid (DNS) method. Addition of PEG has been proven to facilitate enzymatic hydrolysis of lignocellulosic materials. Furthermore, PEG had the positive effect on hydrolytic enzyme activity of pure cellulose materials without lignin. Changes in lignocellulose materials have been observed by inverted microscope and Scanning electron microscope (SEM), and no chemical changes were shown by Fourier transform infrared spectroscopy (FTIR). The promotion of PEG on enzymatic hydrolysis of pure cellulose materials may be due to its loose physical structure and similar phenomenon in natural lignin materials. PEG loosens the physical structure of lignocellulose, thus facilitating enzymatic hydrolysis. This may be a new idea to optimize the lignocellulosic enzymatic hydrolysis process.

The adsorption properties of endoglucanase to lignin and their impact on hydrolysis

Nonproductive adsorption of cellulase to lignin dramatically influenced the hydrolysis efficiency of lignocellulose. By comparing the adsorption behaviors of CBH and EG, we found that the adsorption of EG to lignin showed lower adsorption velocity and capacity versus CBH. During the adsorption of EG to lignin, carbohydrate binding domain (CBM) and catalytic domain (CD) both played an important role by a two-step adsorption process, in which CD slowly bond on lignin and developed stronger interaction with lignin. The optimal binding position of EG on lignin was consistent with that on polysaccharide located in the open catalytic tunnel. So, the adsorption of EG to lignin not only limited the movement of enzyme, but also restricted the catalytic ability of enzyme, which dramatically influenced enzymatic hydrolysis. Increasing the proportion of EG in cellulase cocktails or engineering "weak lignin adsorbed" EG was necessary to relieve the influence of lignin adsorption on hydrolysis.

Improving cellulose nanofibrillation of waste wheat straw using the combined methods of prewashing, p-toluenesulfonic acid hydrolysis, disk grinding, and endoglucanase post-treatment

Here we established a new approach for improving the cellulose nanofibrillation of high ash content waste wheat straw (WWS). The results were comprehensively elucidated from the ash removal, delignification, mechanical fibrillation and endoglucanase post-treatment. When water dosage was increased from 50 to 500 times of the WWS weight, the ash content gradually decreased during prewashing process, which facilitated lignin solubilization in subsequent p-toluenesulfonic acid (p-TsOH) hydrolysis. Approximately 80% of lignin in prewashed WWS could be dissolved during acid hydrolysis to result in a relatively higher crystallinity of 59.1%. Compared with the lignocellulosic nanofibrils (LCNF) directly obtained using acid hydrolysis and disk grinding, prewashing-assisted acid hydrolyzed WWS was fibrillated into LCNF with smaller height of 57.0 nm. Mild endoglucanase post-treatment could further produce less entangled LCNF with thinner diameters. In short, this study presented a promising and green pathway to achieve an efficient utilization of agricultural residue wastes to cellulose nanomaterials.

Using temperature-responsive zwitterionic surfactant to enhance the enzymatic hydrolysis of lignocelluloses and recover cellulase by cooling

Some zwitterionic surfactants exhibit upper critical solution temperature (UCST) in aqueous solutions. For the zwitterionic surfactant solution mixed with cellulase, when its temperature is below UCST, the cellulase can be recovered by coprecipitation with zwitterionic surfactant. In this work, 3-(Hexadecyldimethylammonio) propanesulfonate (SB3-16) was selected to enhance the enzymatic hydrolysis of lignocelluloses and recover the cellulase. After adding 2mmol/L of SB3-16, the enzymatic digestibility of eucalyptus pretreated by dilute acid (Eu-DA) and by sulfite (Eu-SPORL) increased from 27.9% and 35.1% to 72.6% and 89.7%, respectively. The results showed that SB3-16 could reduce the non-productive adsorption of cellulase on hydrophobic interface, while it did not significantly inhibit the activity of cellulase. For the solution contained 1wt% SB3-16 and 200mg protein/L CTec2 cellulase, 55.2% of protein could be recovered by cooling. The filter paper activity of the recovered cellulase was 1.93FPU/mg protein, which was 95.8% of its initial activity.

Optimization of simultaneous saccharification and fermentation conditions with amphipathic lignin derivatives for concentrated bioethanol production

Amphipathic lignin derivatives (A-LDs) prepared from the black liquor of soda pulping of Japanese cedar are strong accelerators for bioethanol production under a fed-batch simultaneous enzymatic saccharification and fermentation (SSF) process. To improve the bioethanol production concentration, conditions such as reaction temperature, stirring program, and A-LDs loadings were optimized in both small scale and large scale fed-batch SSF. The fed-batch SSF in the presence of 3.0g/L A-LDs at 38°C gave the maximum ethanol production and a high enzyme recovery rate. Furthermore, a jar-fermenter equipped with a powerful mechanical stirrer was designed for 1.5L-scale fed-batch SSF to achieve rigorous mixing during high substrate loading. Finally, the 1.5L fed-batch SSF with a substrate loading of 30% (w/v) produced a high ethanol concentration of 87.9g/L in the presence of A-LDs under optimized conditions.

Using polyvinylpyrrolidone to enhance the enzymatic hydrolysis of lignocelluloses by reducing the cellulase non-productive adsorption on lignin

Polyvinylpyrrolidone (PVP) is an antifouling polymer to resist the adsorption of protein on solid surface. Effects of PVP on the enzymatic hydrolysis of pretreated lignocelluloses and its mechanism were studied. Adding 1g/L of PVP8000, the enzymatic digestibility of eucalyptus pretreated by dilute acid (Eu-DA) was increased from 28.9% to 73.4%, which is stronger than the classic additives, such as PEG, Tween and bovine serum albumin. Compared with PEG4600, the adsorption of PVP8000 on lignin was larger, and the adsorption layer was more stable and hydrophilic. Therefore, PVP8000 reduced 73.1% of the cellulase non-productive adsorption on lignin and enhanced the enzymatic hydrolysis of lignocelluloses greatly.