Microalgal lipids production and nutrients recovery from landfill leachate using membrane photobioreactor

A new microalgal negative carbon technology for landfill leachate treatment: Simultaneous removal of nitrogen and phosphorus

Replete with ammonia nitrogen and organic pollutants, landfill leachate typically undergoes treatment employing expensive and carbon-intensive integrated techniques. We propose a novel microalgae technology for efficient, low-carbon simultaneous treatment of carbon, nitrogen, and phosphorus in landfill leachate (LL). The microbial composition comprises a mixed microalgae culture with Chlorella accounting for 82.58%. After seven days, the process with an N/P ratio of approximately 14:1 removed 98.81% of NH4+-N, 88.62 % of TN, and 99.55% of TP. Notably, the concentrations of NH4+-N and TP met the discharge standards, while the removal rate of NH4+-N was nearly three times higher than previously reported in relevant studies. The microalgae achieved a removal efficiency of 64.27% for Total Organic Carbon (TOC) and 99.26% for Inorganic Carbon (IC) under mixotrophic cultivation, yielding a biomass of 1.18 g/L. The treatment process employed in this study results in a carbon emissions equivalent of -8.25 kgCO2/kgNremoved, representing a reduction of 33.56 kgCO2 compared to the 2AO + MBR process. In addition, shake flask experiments were conducted to evaluate the biodegradability of leachate after microalgae treatment. After microalgae treatment, the TOCB (Biodegradable Total Organic Carbon)/TOC ratio decreased from 56.54% to 27.71%, with no significant improvement in biodegradability. It establishes a fundamental foundation for further applied research in microalgae treatment of leachate.

Utilization of microbial fuel cells as a dual approach for landfill leachate treatment and power production: a review

Landfill leachate, which is a complicated organic sewage water, presents substantial dangers to human health and the environment if not properly handled. Electrochemical technology has arisen as a promising strategy for effectively mitigating contaminants in landfill leachate. In this comprehensive review, we explore various theoretical and practical aspects of methods for treating landfill leachate. This exploration includes examining their performance, mechanisms, applications, associated challenges, existing issues, and potential strategies for enhancement, particularly in terms of cost-effectiveness. In addition, this critique provides a comparative investigation between these treatment approaches and the utilization of diverse kinds of microbial fuel cells (MFCs) in terms of their effectiveness in treating landfill leachate and generating power. The examination of these technologies also extends to their use in diverse global contexts, providing insights into operational parameters and regional variations. This extensive assessment serves the primary goal of assisting researchers in understanding the optimal methods for treating landfill leachate and comparing them to different types of MFCs. It offers a valuable resource for the large-scale design and implementation of processes that ensure both the safe treatment of landfill leachate and the generation of electricity. The review not only provides an overview of the current state of landfill leachate treatment but also identifies key challenges and sets the stage for future research directions, ultimately contributing to more sustainable and effective solutions in the management of this critical environmental issue.

Coagulation pretreatment coupled with indigenous microalgal-bacterial consortium system for on-site treatment of rural black wastewater

Improper treatment of rural black wastewater (RBW) presents substantial challenges, including the wastage of resource, environmental contamination, and economic consequences. This study proposed an integrated process for RBW treatment, consisting of coagulation/flocculation (C/F) pretreatment and subsequent inoculation of indigenous microalgal-bacterial consortium (IMBC) for nitrogen recovery, namely C/F-IMBC process. Specifically, the optimal C/F conditions (polyaluminium chloride of 4 g/l, polyacrylamide of 50 mg/l, and pH of 6) were determined through a series of single-factor experiments, considering CN, turbidity, and dissolved organic matter (DOM) removal, economic cost, and potential influence on the water environment. Compared to the sole IMBC system for RBW treatment, the proposed C/F-IMBC process exhibited a remarkable 1.23-fold increase in microalgal growth and a substantial 17.6-22.6 % boost in nitrogen recovery. The altered RBW characteristic induced by C/F pretreatment was supposed to be responsible for the improved system performance. In particular, the abundance of DOM was decreased and its composition was simplified after C/F pretreatment, based on the analysis for excitation-emission matrices with parallel factor and gas chromatography-mass spectrometry, thus eliminating the potential impacts of toxic DOM components (e.g., Bis(2-ethylhexyl) phthalate) on IMBC activity. It should also be noted that C/F pretreatment modified microbial community structure as well, thereby regulating the expression of nitrogen-related genes and enhancing the system nitrogen recovery capacity. For instance, the functional Cyanobacteria responsible for nutrient recovery was enriched by 1.95-fold and genes involved in the assimilatory nitrate reduction to ammonia pathway were increased by 1.52-fold. These fundamental findings are expected to offer insights into the improvement of DOM removal and nitrogen recovery for IMBC-based wastewater treatment system, and provide valuable guidance for the development of sustainable on-site RBW treatment technologies.

Environmental pitfalls and associated human health risks and ecological impacts from landfill leachate contaminants: Current evidence, recommended interventions and future directions

The improper management of solid waste, particularly the dumping of untreated municipal solid waste, poses a growing global challenge in both developed and developing nations. The generation of leachate is one of the significant issues that arise from this practice, and it can have harmful impacts on both the environment and public health. This paper presents an overview of the primary waste types that generate landfill leachate and their characteristics. This includes examining the distribution of waste types in landfills globally and how they have changed over time, which can provide valuable insights into potential pollutants in a given area and their trends. With a lack of specific regulations and growing concerns regarding environmental and health impacts, the paper also focuses on emerging contaminants. Furthermore, the environmental and ecological impacts of leachate, along with associated health risks, are analyzed. The potential applications of landfill leachate, suggested interventions and future directions are also discussed in the manuscript. Finally, this work addresses future research directions in landfill leachate studies, with attention, for the first time to the potentialities that artificial intelligence can offer for landfill leachate management, studies, and applications.

Microalgae biofuels: illuminating the path to a sustainable future amidst challenges and opportunities

The development of microalgal biofuels is of significant importance in advancing the energy transition, alleviating food pressure, preserving the natural environment, and addressing climate change. Numerous countries and regions across the globe have conducted extensive research and strategic planning on microalgal bioenergy, investing significant funds and manpower into this field. However, the microalgae biofuel industry has faced a downturn due to the constraints of high costs. In the past decade, with the development of new strains, technologies, and equipment, the feasibility of large-scale production of microalgae biofuel should be re-evaluated. Here, we have gathered research results from the past decade regarding microalgae biofuel production, providing insights into the opportunities and challenges faced by this industry from the perspectives of microalgae selection, modification, and cultivation. In this review, we suggest that highly adaptable microalgae are the preferred choice for large-scale biofuel production, especially strains that can utilize high concentrations of inorganic carbon sources and possess stress resistance. The use of omics technologies and genetic editing has greatly enhanced lipid accumulation in microalgae. However, the associated risks have constrained the feasibility of large-scale outdoor cultivation. Therefore, the relatively controllable cultivation method of photobioreactors (PBRs) has made it the mainstream approach for microalgae biofuel production. Moreover, adjusting the performance and parameters of PBRs can also enhance lipid accumulation in microalgae. In the future, given the relentless escalation in demand for sustainable energy sources, microalgae biofuels should be deemed a pivotal constituent of national energy planning, particularly in the case of China. The advancement of synthetic biology helps reduce the risks associated with genetically modified (GM) microalgae and enhances the economic viability of their biofuel production.

Marine diatom algae cultivation in simulated dairy wastewater and biomass valorization

Liquid byproducts and organic wastes generated from dairy processing units contribute as the largest source of industrial food wastewater. Though bacteria-mediated treatment strategies are largely implemented, a more effective and innovative management system is needed of the hour. Thus, the current study involves the cultivation of centric diatoms, Chaetoceros gracilis, and Thalassiosira weissflogii in simulated dairy wastewater (SDWW) formulated using varying amounts of milk powder with artificial seawater f/2 media (ASW). The results revealed that cell density and biomass productivity were highest in the 2.5% SDWW treatment cultures of both the strains, the maximum being in C. gracilis (7.5 × 106 cells mL - 1; 21.1 mg L-1 day-1). Conversely, the total carotenoid, chrysolaminarin, and phenol content were negatively impacted by SDWW. However, a considerable enhancement in the total lipid content was reported in the 2.5% SDWW culture of both species. Furthermore, the fatty acid profiling revealed that though the total polyunsaturated fatty acid (PUFA) content was highest in the control setups, the total mono polyunsaturated fatty acid (MUFA) content was higher in the 5% SDWW setups (30.66% in C. gracilis and 33.21% in T. weissflogii). In addition to it, in the cultures utilizing energy from external carbon sources provided by SDWW, the biodiesel produced was also enhanced owing to the heightened cetane number. Thus, the current study evidently highlights the organic carbon acquisition potential of marine diatoms with the scope of providing sustainable biorefinery.

Nutrient recovery from municipal solid waste leachate in the scope of circular economy: Recent developments and future perspectives

Holistically considering the current situation of the commercial synthetic fertilizer (CSF) market, recent global developments, and future projection studies, dependency on CSFs in agricultural production born significant risks, especially to the food security of foreign-dependent countries. The foreign dependency of countries in terms of CSFs can be reduced by the concepts such as the circular economy and resource recovery. Recently, waste streams are considered as a source in order to produce recovery-based fertilizers (RBF). RBFs produced from different waste streams can be substituted with CSFs as input for agricultural applications. Municipal solid waste leachate (MSWL) is one of the waste streams that have a high potential for RBF production. Distribution of the published papers over the years shows that this potential was noticed by more researchers in the millennium. MSWL contains a remarkable amount of nitrogen and phosphorus which are the main nutrients required for agricultural production. These nutrients can be recovered with many different methods such as microalgae cultivation, chemical precipitation, ammonia stripping, membrane separation, etc. MSWL can be generated within the different phases of municipal solid waste (MSW) management. Although it is mainly composed of landfill leachate (LL), composting plant leachate (CPL), incineration plant leachate (IPL), and transfer station leachate (TSL) should be considered as potential sources to produce RBF. This study compiles studies conducted on MSWL from the perspective of nitrogen and phosphorus recovery. Moreover, recent developments and limitations of the subject were extensively discussed and future perspectives were introduced by considering the entire MSW management. Investigated studies in this review showed that the potential of MSWL to produce RBF is significant. The outcomes of this paper will serve the countries for ensuring their food security by implementing the resource recovery concept to produce RBF. Thus, the risks born with the recent global developments could be overcome in this way besides the positive environmental outcomes of resource recovery.

Revealing mechanism and influence of microalgae cells' periodical auto-agglomeration induced by high concentration of carbon dioxide

The efficient cultivation of microalgae using CO₂ from flue gas can be a win-win situation for both environmental protection and energy accessibility. In general, 10-20% of CO₂ in flue gas would decrease pH and inhibit microalgae growth. However, Chlorella sorokiniana MB-1 under 15% CO₂ showed a periodical auto-agglomeration, which promoted microalgae growth on the contrary in this study. The maximum biomass concentration of 3.27 g L^-1 was higher than that cultivated with an optimal CO₂ concentration. The pH decreased to 6.04 after the mixed gas with 15% CO₂ (v/v) was bubbled into medium for 0.5 hours, which resulted in auto-agglomeration to protect microalgae from acidification and keep a high specific growth rate of 0.03 h^-1. Then the pH recovered to 7 during stabilization phase, auto-agglomeration ratio was up to 100% because of lamellar extracellular polymeric substances. Therefore, the interesting periodical agglomeration both enhanced growth and simplified harvesting.

Nutrient removal and lipid production by the co-cultivation of Chlorella vulgaris and Scenedesmus dimorphus in landfill leachate diluted with recycled harvesting water

Applying microalgae for landfill leachate (LL) treatment is promising. However, LL usually needs to be diluted with much fresh water, aggravating water shortage. In this study, mono- and co-culturing microalgae (Chlorella vulgaris and Scenedesmus dimorphus) were used to treat LL diluted with recycled harvesting water, to investigate nutrient removal and lipid production. The results showed that microalgae in co-culture treatment had more biomass and stronger superoxide dismutase activity, which might be related to humic acids contained in recycled harvesting water, according to dissolved organic matters (DOMs) analysis. In addition, the lipid content and yield of co-cultured microalgae reached 27.60 % and 66.87 mg·L^-1, respectively, higher than those of mono-culture, proving the potential of co-culture for the improvement of lipid production. This study provided a freshwater-saving dilution method for LL treatment with recycled harvesting water as well as a strategy for the increase of biomass and lipid accumulation by microalgae co-cultivation.

A review on landfill system for municipal solid wastes: Insight into leachate, gas emissions, environmental and economic analysis

Landfill is one of the common processes for removing and disposing waste materials that comprises the final method of disposing municipal solid waste. Disposal of municipal solid waste through land filling has become an important environmental problem all over the world which results in environmental contamination and pollution. Microbes present in the land act on the dumped materials and decompose the organic content present. The leachate from landfill is rich in organic, inorganic and suspended particles which may cause threat to ecosystem. The pollutants from leachate may be heavy metals, organic and inorganic content and organic compounds. The geological properties of soil get altered when leachate migrates. The physical, chemical and biological properties of the dumped material are determined by the decomposition of substances and microbes acting onto it. Trace gas emission may occur due to volatilization of chemical substances, degradation of waste materials and conversion reactions. The concentration of gas released varies from region to region of dumping, covered and uncovered dumped materials. The current review recommends an engineered landfill design helpful for landfill gas generation which replaces the fossil fuel as a compressed natural gas or liquefied natural gas. The landfill area is separated into organic and inorganic cells to scope at the objective of energy generation and resource recovery. However, the impact of these released gaseous emissions has been analyzed completely.

Leachate decontamination through biological processes coupled to advanced oxidation: A review

The landfill leachate is considered a toxic effluent composed of recalcitrant contaminants that requires innovative alternatives for its decontamination. Coupling between advanced oxidation processes (AOPs) and aerobic biological treatments are highlighted in this research. Therefore, a bibliographic review of the research made from 2010 to 2021 was developed. These combined alternatives were applied in leachates, and it is oriented toward the analysis of knowledge gaps, trends, and future proposals of the treatment combined that contribute to researchers who wish to work on the subject. These kinds of treatments were chosen due to a bibliometric analysis made. Also, the information was searched in several scientific database. This work was found to be unpublished, as no reviews were found so far that agglomerate studies of coupling between photocatalytic and aerobic biological processes to treat leachates. Besides, AOPs are ideal for treating wastewater of complex composition, however, when it is used as the only treatment, they are usually unprofitable, which justifies their coupling with biological treatments. Subsequently, it was determined that the knowledge main gap is the lack of documentation of treatment costs, which makes it difficult to implement on a real scale. In addition to this, the couplings trends are toward doping with metallic and nonmetallic ions of the catalyst used in the photocatalytic process to improve the efficiency of these. Finally, future research should work on finding alternatives that allow the optimization of the resources used in the combined systems and on promoting the recovery of existing products in the leachate.Implications: Leachates generate several environmental impacts due to their toxic composition. Even when coupling between heterogeneous photocatalysis and biologic treatment can solve them, issues like cost analysis and the scaling-up factor have not been developed, and futures researchers should work on that. Besides, the trend founded in almost all investigations was the catalyst doping with metals and nonmetals ions, particularly when they use TiO2 because it gives the possibility of improving efficiencies just with a structural variation. Finally, these treatment combinations require more analyses and comparison of their remotion over emerging pollutants and their performance with new designs.

Microalgae-based removal of pollutants from wastewaters: Occurrence, toxicity and circular economy

The natural and anthropogenic sources of water bodies are contaminated with diverse categories of pollutants such as antibiotics, pharmaceuticals, pesticides, heavy metals, organic compounds, and other industrial chemicals. Depending on the type and the origin of the pollutants, the degree of contamination can be categorized into lower to higher concentrations. Therefore, the removal of hazardous chemicals from the environment is an important aspect. The physical, chemical and biological approaches have been developed and implemented to treat wastewaters. The microbial and algal treatment methods have emerged as a growing field due to their eco-friendly and sustainable approach. Particularly, microalgae emerged as a potential organism for the treatment of contaminated water bodies. The microalgae of the genera Chlorella, Anabaena, Ankistrodesmus, Aphanizomenon, Arthrospira, Botryococcus, Chlamydomonas, Chlorogloeopsis, Dunaliella, Haematococcus, Isochrysis, Nannochloropsis, Porphyridium, Synechococcus, Scenedesmus, and Spirulina reported for the wastewater treatment and biomass production. Microalgae have the potential for adsorption, bioaccumulation, and biodegradation. The microalgal strains can mitigate the hazardous chemicals via their diverse cellular mechanisms. Applications of the microalgae strains were found to be effective for sustainable developments and circular economy due to the production of biomass with the utilization of pollutants.

Micro-algae assisted green bioremediation of water pollutants rich leachate and source products recovery

Water management and treatment are high concern fields with several challenges due to increasing pollutants produced by human activity. It is imperative to find integral solutions and strategic measures with robust remediation. Landfill leachate production is a high concern emerging problem. Especially in low middle-income countries due to no proper local waste disposition regulation and non-engineered implemented methods to dispose of urban waste. These landfills can accumulate electronic waste and release heavy metals during the degradation process. Similar phenomena include expired pharmaceuticals like antibiotics. All these pollutants accumulated in leachate made it hard to dispose of or treat. Leachate produced in non-engineered landfills can permeate soils and reach groundwater, dragging different contaminants, including antibiotics and heavy metals, which eventually can affect the environment, changing soil properties and affecting wildlife. The presence of antibiotics in the environment is a problem with particular interest to solve, mainly to avoid the development of antibiotic-resistant microorganisms, which represent a future risk for human health with possible epidemic implications. It has been reported that the use of contaminated water with heavy metals to produce and grow vegetables is a risk for consumers, heavy metals effects in humans can include carcinogenic induction. This work explores the opportunities to use leachate as a source of nutrients to grow microalgae. Microalgae stand out as an alternative to bioremediate leachate, at the same time, microalgae produce high-value compounds that can be used in bioplastic, biofuels, and other industrial applications.

Enhancing nitrogen removal in mature landfill leachate by mixed microalgae through elimination of inhibiting factors

Nitrogen removal from landfill leachate (LL) using microalgae is a promising method and can realize CO₂ mitigation. But the performances are usually inhibited by high chromaticity, high free ammonia (FAN) and some complex macro molecular organic matter (MOM) in the LL. To achieve efficient nitrogen removal from LL, this study firstly pretreated the mature LL with ozone, decolorizer and activated sludge (AS) respectively, and then inoculated with mixed microalgae. The results showed that the synergistic effect of ozonation and microalgae was the best among the three, with 99.7% ammonia removal, 0.77 g/L (dry weight) microalgae biomass, and a maximum growth rate of 160 mg/L/d. Ozonation pretreatment significantly reduced the chromaticity and macromolecular organic matter of LL, with the chromaticity reduced from 2225 to 225 times and the 3D fluorescence intensity representing MOM reduced from 4089 a.u. to 986.1 a.u.. And it was found that the mixed microalgae grown after pretreatment by three different methods all were mostly Chlorella and very few Microcystis, and the density of microalgal populations (number of cells per unit volume) after ozonation was up to 10,650 cells/μL. This work provides a feasible and an economical way to remove ammonia nitrogen (NH+ 4-N) from landfill leachate.

Production, Processing, and Protection of Microalgal n-3 PUFA-Rich Oil

Microalgae have been increasingly considered as a sustainable “biofactory” with huge potentials to fill up the current and future shortages of food and nutrition. They have become an economically and technologically viable solution to produce a great diversity of high-value bioactive compounds, including n-3 polyunsaturated fatty acids (PUFA). The n-3 PUFA, especially eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), possess an array of biological activities and positively affect a number of diseases, including cardiovascular and neurodegenerative disorders. As such, the global market of n-3 PUFA has been increasing at a fast pace in the past two decades. Nowadays, the supply of n-3 PUFA is facing serious challenges as a result of global warming and maximal/over marine fisheries catches. Although increasing rapidly in recent years, aquaculture as an alternative source of n-3 PUFA appears insufficient to meet the fast increase in consumption and market demand. Therefore, the cultivation of microalgae stands out as a potential solution to meet the shortages of the n-3 PUFA market and provides unique fatty acids for the special groups of the population. This review focuses on the biosynthesis pathways and recombinant engineering approaches that can be used to enhance the production of n-3 PUFA, the impact of environmental conditions in heterotrophic cultivation on n-3 PUFA production, and the technologies that have been applied in the food industry to extract and purify oil in microalgae and protect n-3 PUFA from oxidation.

Improving reverse osmosis concentrate treatment and nutrients conversion to Chlorella vulgaris bioenergy assisted with granular activated carbon

Landfill leachate (LL), especially the reverse osmosis concentrate (ROC), is a societal burden due to high toxicity but may have intrinsic values attributing to copious nutrients and organics. ROC bioremediation by microalgae has attracted much attentions benefiting from its extra advantage of bioenergy production. However, efficient microalgae cultivation with ROC is still a challenging task attributing to notorious ROC characteristics, like high chromaticity and toxicity. To alleviate these negative influences, a technique integrating granular activated carbon (GAC) pretreatment and microalgae bioremediation was proposed, with which nitrogen and phosphorus removal efficiencies achieved 100% along with an optimized microalgal biomass concentration of 1.44 g/L and lipid yield of 482.4 mg/L. Furthermore, a total volumetric energy yield of 33.6 kJ/L was acquired, which was conducive to realize energy valorization. The visualization evidence of three-dimensional fluorescence spectroscopy revealed chromaticity degradation mechanism of ROC as humic acids reduction and transfer to family of soluble microbial by-products. Meanwhile, contributions of GAC adsorption and microalgae assimilation on nutrients removal were analyzed. Together, this work provides a promising method and valuable information for ROC bioremediation with microalgae.

Bio-membrane integrated systems for nitrogen recovery from wastewater in circular bioeconomy

Wastewater contains a significant amount of recoverable nitrogen. Hence, the recovery of nitrogen from wastewater can provide an option for generating some revenue by applying the captured nitrogen to producing bio-products, in order to minimize dangerous or environmental pollution consequences. The circular bio-economy can achieve greater environmental and economic sustainability through game-changing technological developments that will improve municipal wastewater management, where simultaneous nitrogen and energy recovery are required. Over the last decade, substantial efforts were undertaken concerning the recovery of nitrogen from wastewater. For example, bio-membrane integrated system (BMIS) which integrates biological process and membrane technology, has attracted considerable attention for recovering nitrogen from wastewater. In this review, current research on nitrogen recovery using the BMIS are compiled whilst the technologies are compared regarding their energy requirement, efficiencies, advantages and disadvantages. Moreover, the bio-products achieved in the nitrogen recovery system processes are summarized in this paper, and the directions for future research are suggested. Future research should consider the quality of recovered nitrogenous products, long-term performance of BMIS and economic feasibility of large-scale reactors. Nitrogen recovery should be addressed under the framework of a circular bio-economy.

Hydrothermal hydrolysis of algal biomass for biofuels production: A review

Hydrothermal hydrolysis is an energy-efficient and economical pretreatment technology to disrupt the algal cells and hydrolyze the intracellular compounds, thereby promoting the biofuels production of fermentation. However, complex reaction mechanisms, unpredictable rheological properties of algal slurry, and immature continuous reactors still constrain the commercialization of such a process. To systematically understand the existing status and lay a foundation for promoting the technology, the chemical mechanism of hydrothermal hydrolysis of algal biomass is elaborated in this paper, and the influences of temperature, residence time, total solid content, and pH, on the biomethane production of hydrolyzed algal biomass are summarized. Besides, a comprehensive overview of the rheological behavior of algal slurries is discussed at various operational factors. The recent advances in flow, heat and mass transfer model coupling with the generic kinetics model in continuous reactors and the application of energy-saving strategies for efficient algal biomass pretreatment are detailed reviewed.

An approach for dairy wastewater remediation using mixture of microalgae and biodiesel production for sustainable transportation

The aim of this work is remediation of dairy wastewater (DWW) for biodiesel feedstock production using poly-microalgae cultures of four microalgae namely Chlorella minutissima (C. minutissima), Scenedesmus abundans (S. abundans), Nostoc muscorum (N. muscorum) and Spirulina sp. The poly-microalgae cultures were prepared as C. minutissima + N. muscorum (CN), C. minutissima + N. muscorum + Spirulina sp. (CNSS) and S. abundans + N. muscorum + Spirulina sp. (SNSS). Poly-microalgae culture CNSS cultivated on 70% DWW achieved 75.16, 61.37, 58.76, 84.48 and 84.58%, removals of biological oxygen demand (BOD), chemical oxygen demand (COD), total nitrogen (TN), total phosphorus (TP), and suspended solids (SS), respectively, at 12:12 h photoperiod that resulted into total biomass and lipid yield of 3.47 ± 0.07 g/L and 496.32± 0.065 mg/L. However, maximum biomass and lipid yields of 5.76 ± 0.06 and 1152.37 ± 0.065 mg/L were achieved by poly-microalgae culture CNSS cultivated on 70% DWW + 10 g/L of glucose at 18:6 h photoperiod. Fatty acid methyl ester (FAME) analysis shown presence of C14:0 (myristic acid) C16:0 (palmitic acid), C16:1 (palmitoleic acid), C18:0 (stearic acid), C18:2 (linoleic acid) and C18:3 (linolenic acid), it indicates that the lipids produced from poly-microalgae cultures are suitable for biodiesel production. Thus, poly-microalgae cultures could be more efficient than mono-microalgae cultures in the remediation of DWW and for biodiesel feedstock production.

Technical and economic evaluation of the integration of membrane bioreactor and air-stripping/absorption processes in the treatment of landfill leachate

A membrane bioreactor inoculated with commercial baker's yeast (Saccharomyces cerevisiae) (MBRy) integrated to an air-stripping/absorption (AS/AB) as pre-treatment (aiming ammonia recovery) or a post-treatment (polishment step) was assessed for the landfill leachate treatment. The effect of chemical oxygen demand (COD) and nitrogen (N) ratio (C:N) on the performance of the MBRy was also investigated. At high COD/N ratio, high organic matter removal in terms of COD (71 ± 4%) and ammonia removal (97 ± 3%) was observed. Lower COD/N ratio favored yeast growth in the mixed liquor even under adverse conditions. The results of ammonia removal and recovery, and economic analysis demonstrated that the best way to integrate the AS/BS processes is as pre-treatment of MBRy. The ammonia concentration in the AS/AB process feed was a key factor to achieve the market specification. Although pH and temperature adjustment were adequate to promote ammonia removal/recovery, the AS operation at high temperatures showed the highest ammonia removal rate (99%). Therefore, the integration of AS/AB with MBRy allows obtaining a permeate with a final concentration of 2902 ± 374 mg L^-1 of COD and 9 ± 7.5 mg L^-1 of ammonia. Although it was possible to reach the Brazilian discharge standard for ammonia (20 mg L^-1), it was not possible to reach the standard for COD, where the remaining fraction is recalcitrant organic matter, requiring the integration of a physico-chemical process. It should be noted that the proposed route allowed recovery 7 kg of ammonia per m³ of treated leachate.

Environmental, human health, and economic implications of landfill leachate treatment for per- and polyfluoroalkyl substance removal

Landfill leachate is commonly treated offsite with municipal wastewater. This offsite leachate treatment may be limited or no longer applicable due to the increasingly stringent regulations and concerns related to per- and polyfluoroalkyl substance (PFAS) discharge into the environment, resulting in development of full-scale, onsite leachate treatment facilities. To help landfills prepare for the potential shift from offsite to onsite leachate treatment for PFAS compliance, this study analyzed and compared the environmental, human health, and economic performances of a typical onsite and a typical offsite leachate treatment alternative through life cycle assessment (LCA) and life cycle cost assessment (LCCA) using a landfill site located in Zhuzhou, China as a testbed. Two distinct functional units (FUs) were investigated: 1 m³ of leachate treated and 1 g of PFAS removed. Our results show that the onsite scenario offered benefits from human health and economic perspectives, while the offsite scenario generally performed better from the environmental perspective when a leachate PFAS concentration of 150,704 ng/L was assumed. The extent of this tradeoff varied when different functional units were adopted. The onsite scenario will not be competitive from all three perspectives when PFAS concentration in the raw leachate is less than 1666 ng/L.

A survey on experiences in leachate treatment: Common practices, differences worldwide and future perspectives

The necessity for landfill leachate treatment is a requisite to reduce the environmental impact related to municipal solid waste landfills and different aspects must be considered while deciding for an appropriate treatment process. For example, it was demonstrated that the landfill leachate stabilization in tropical regions is achieved right after its first year of operation, requiring technologies capable of treating leachates of a higher recalcitrant character if compared to those leachates from temperate regions and same landfill age. In view of its complexity and variability, stand-alone processes (either biological or physicochemical) are often ineffective in attaining the threshold values for its discharge in receiving bodies. Due to that fact, full-scale facilities have adopted integrated routes, harvesting the benefits of both biological and physicochemical processes. The implementation of membrane bioreactors followed by polishing membrane separation process (nanofiltration and reverse osmosis) seems to be a trend in leachate treatment by full-scale treatment plants. This technology is widely employed in China, European countries, and tropical countries as Brazil, generally with a treatment cost lower than the costs related to its disposal in domestic effluent collection systems. From the technologies already employed by full-scale facilities, four integrated routes were proposed for a sensitive analysis considering the treatment of a landfill leachate of different physicochemical characteristics. From all routes, those employing the membrane separation process as a polishing step had a better efficacy in attaining the threshold values for leachate disposal, being that an interesting alternative for leachate polishing by full-scale facilities.

Adapting the algal microbiome for growth on domestic landfill leachate

We aimed to improve algal growth rate on leachate by optimising the algal microbiome. An algal-bacterial consortium was enriched from landfill leachate and subjected to 24 months of adaptive laboratory evolution, increasing the growth rate of the dominant algal strain, Chlorella vulgaris, almost three-fold to 0.2 d^-1. A dramatic reduction in nitrate production suggested a shift in biological utilisation of ammoniacal-N, supported by molecular 16S rRNA taxonomic analyses, where Nitrosomonas numbers were not detected in the adapted consortium. A PICRUSt approach predicted metagenomic functional content and revealed a high number of sequences belonging to bioremediation pathways, including degradation of aromatic compounds, benzoate and naphthalene, as well as pathways known to be involved in algal-bacterial symbiosis. This study enhances our understanding of beneficial mechanisms in algal-bacterial associations in complex effluents, and ultimately enables the bottom-up design of optimised algal microbiomes for exploitation within industry.

Immobilization altering the growth behavior, ammonium uptake and amino acid synthesis of Chlorella vulgaris at different concentrations of carbon and nitrogen

Nitrogen recycling by microalgae has aroused considerable attention. In this study, immobilized Chlorellavulgaris with 5-day mixotrophic cultivation to recover ammonium (NH₄⁺-N) were systematically investigated under various sodium acetate (CH₃COONa) and ammonium chloride (NH₄Cl) concentrations, and evaluated by comparison with suspended cells. The results revealed that, unlike suspended cells, NH₄⁺-N uptake by immobilized cells was not in direct proportion to chemical oxygen demand (COD) concentrations. The immobilized cells to NH₄⁺-N uptake was all inferior to that of suspended cells, presenting the maximum rate of 68.92% in group of 30 mg/L NH₄⁺-N and 200 mg/L COD. Free amino acids in immobilized cells such as glutamate (Glu), arginine (Arg), proline (Pro) and leucine (Leu) were more sensitive to NH₄⁺-N assimilation, as higher values observed by suspended cells. Low carbon-nitrogen (C/N) ratio showed remarkable benefits to amino acid synthesis. These results could provide a reference for manipulating the algal system and biomass accumulation.

Treatment of Wastewaters by Microalgae and the Potential Applications of the Produced Biomass—A Review

The treatment of different types of wastewater by physicochemical or biological (non-microalgal) methods could often be either inefficient or energy-intensive. Microalgae are ubiquitous microscopic organisms, which thrive in water bodies that contain the necessary nutrients. Wastewaters are typically contaminated with nitrogen, phosphorus, and other trace elements, which microalgae require for their cell growth. In addition, most of the microalgae are photosynthetic in nature, and these organisms do not require an organic source for their proliferation, although some strains could utilize organics both in the presence and absence of light. Therefore, microalgal bioremediation could be integrated with existing treatment methods or adopted as the single biological method for efficiently treating wastewater. This review paper summarized the mechanisms of pollutants removal by microalgae, microalgal bioremediation potential of different types of wastewaters, the potential application of wastewater-grown microalgal biomass, existing challenges, and the future direction of microalgal application in wastewater treatment.

Integrating gravity settler with an algal membrane photobioreactor for in situ biomass concentration and harvesting

Gravity settler was integrated into an algal membrane photobioreactor (MPBR) for in situ biomass concentration and harvesting of Graesiella emersonii. By continuous circulation of suspended biomass between MPBR and settler, biomass was sedimented in the settler and harvested. MPBR-Settler operations at different recirculation rates (0.15-2.4 L/d) and settler volumes (250-1000 mL) affected both suspended (0.4-3.4 g/L) and settled (16.1-31.1 g/L) biomass concentrations. Maximum biomass productivity of 0.26 ± 0.06 g/L/d was achieved in the 1000 mL settler operating at 0.6 L/d recirculation rate, which also yielded 9-131 times concentrated biomass (31.1 g/L) compared to the baseline MPBR (0.2-3.4 g/L). This novel design also facilitated MPBR operation at low solids retention times (6-8 d) without incurring large outflow of unfiltered effluent, while alleviating light limitation via biomass dilution. These results demonstrated that the MPBR-Settler system can provide an excellent way to mitigate light limitation, enhance biomass productivity, and simplify biomass harvesting.

Membrane processes

This literature review provides a review for publications in 2018 and 2019 and includes information membrane processes findings for municipal and industrial applications. This review is a subsection of the annual Water Environment Federation literature review for Treatment Systems section. The following topics are covered in this literature review: industrial wastewater and membrane. Bioreactor (MBR) configuration, membrane fouling, design, reuse, nutrient removal, operation, anaerobic membrane systems, microconstituents removal, membrane technology advances, and modeling. Other sub-sections of the Treatment Systems section that might relate to this literature review include the following: Biological Fixed-Film Systems, Activated Sludge, and Other Aerobic Suspended Culture Processes, Anaerobic Processes, and Water Reclamation and Reuse. This publication might also have related information on membrane processes: Industrial Wastes, Hazardous Wastes, and Fate and Effects of Pollutants.

Microalgae carbon fixation integrated with organic matters recycling from soybean wastewater: Effect of pH on the performance of hybrid system

Microalgae have been considered as promising alternative for CO2 fixation and wastewater purification. In our previous work, a hybrid microalgae CO2 fixation concept has been put forward, which initially used carbonate solution absorb CO2, and then provided obtained bicarbonate as nutrition for microalgae growth to avoid the challenge of low CO2 solubility and carbon fixation efficiency in the conventional process. In this work, the proposed hybrid system was further intensified via integrating soybean wastewater nutrition removal with bicarbonate-carbon (NH4HCO3 and KHCO3) conversion. The investigation results indicated that the maximum biomass productivity (0.74 g L-1) and carbon bioconversion efficiency (46.9%) were achieved in low-NH4HCO3 concentration system with pH adjusted to 7. pH adjustment of different bicarbonate systems also enhanced total nitrogen (TN), total phosphorus (TP) and chemical oxygen demand (COD) removal efficiency up to 87.5%, 99.5% and 77.6%, respectively. In addition, maximum neutral lipid (14.4 mg L-1·d-1) and polysaccharide (14.5 mg L-1·d-1) productivities could be obtained in the KHCO3 systems, while higher crude protein productivity (48.1 mg L-1·d-1) was yielded in the NH4HCO3 systems.

Highly efficient reverse osmosis concentrate remediation by microalgae for biolipid production assisted with electrooxidation

Phytoremediation of reverse osmosis concentrate (ROC) with microalgae can simultaneously achieve multi-functions of ROC treatment, CO₂ mitigation and microalgae biolipid production. But the performances are usually inhibited by high free ammonia nitrogen (FAN) concentration and chromaticity of ROC. To offset these negative effects, an integrated technique including electrooxidation pretreatment and Chlorella vulgaris remediation was proposed, in which the ROC was first pretreated with electrooxidation to decrease FAN and chromaticity, and then the oxidized ROC was remediated with microalgae to reclaim nutrients and produce biolipid. Results showed that FAN was sharply reduced from 53.0 mg N/L to 13.9 mg N/L and chromaticity was decreased from 1600 to 100 Pt-Co via electrooxidation. Possible reaction mechanism of nutrients removal was discussed via electron mass balance. Explanation on chromaticity decrease was revealed by analyzing humic acid conversion path with fluorescence characteristics. During microalgae remediation process, nutrients removal rate, microalgae biomass concentration and lipid yield were effectively enhanced in electrooxidized ROC. Energy balance analysis indicated that microalge lipid energy under current density of 3.25 mA/cm² basically compensated total input energy despite ROC sterilization. This work provided a promising strategy for large-scale ROC treatment and microalgae biolipid production.

Prospects of integrating algae technologies into landfill leachate treatment

Landfilling of municipal waste, an environmental challenge worldwide, results in the continuous formation of significant amounts of leachate, which poses a severe contamination threat to ground and surface water resources. Landfill leachate (LL) is generated by rainwater percolating through disposed waste materials and must be treated effectively before safe discharge into the environment. LL contains numerous pollutants and toxic substances, such as dissolved organic matter, inorganic chemicals, heavy metals, and anthropogenic organic compounds. Currently, LL treatment is carried out by a combination of physical, chemical, and microbial technologies. Microalgae are now viewed as a promising sustainable addition to the repertoire of technologies for treating LL. Photosynthetic algae have been shown to grow in LL under laboratory conditions, while some species have also been employed in larger-scale LL treatments. Treating leachate with algae can contribute to sustainable waste management at existing landfills by remediating low-quality water for recycling and reuse and generating large amounts of algal biomass for cost-effective manufacturing of biofuels and bioproducts. In this review, we will examine LL composition, traditional leachate treatment technologies, LL toxicity to algae, and the potential of employing algae at LL treatment facilities. Emphasis is placed on how algae can be integrated with existing technologies for biological treatment of LL, turning leachate from an environmental liability to an asset that can produce value-added biofuels and bioproducts for the bioeconomy.

Photo-bioreactor design for microalgae: A review from the aspect of CO2 transfer and conversion

Photobioreactor (PBR) is the most critical equipment for microalgal photosynthetic fixation of CO₂. It provides suitable environmental conditions, such as CO₂, light and nutrients, for microalgal growth. As the major carbon source for microalgae, CO₂ gas is pumped into PBR with the formation of bubbles and formed gas-liquid flow. The gas-liquid flow affects CO₂ and nutrients transmission as well as microalgae cells distribution in PBR, thereby affecting the biochemical reaction of microalgae. While the migration and transport of biochemical reaction products affect the two-phase flow, phase distribution and flow resistance in the PBR in return, thus affecting the transport of light and nutrients. Therefore, microalgal photosynthetic rate is determined synthetically by two-phase flow and the transport of CO₂, light and nutrients in PBR. Deep understanding of gas-liquid two-phase flow, energy and mass transfer coupling with microalgal growth in PBR is the cornerstone for the design of an efficient microalgae PBR.

Rheokinetics of microalgae slurry during hydrothermal pretreatment processes

Hydrothermal pretreatment is an efficient process for improving the productivity of biofuels from wet microalgae biomass. The rheological behavior of microalgae slurry is a significant parameter affecting the performance of hydrothermal pretreatment reactors. Herein, the dynamic rheological behavior of microalgae slurry during hydrothermal pretreatment was investigated for the first time. The results revealed that the insoluble organics released from microalgae cells was the main factor affecting the rheological behavior of microalgae slurry. The denaturation and hydrolysis of starch and protein in liquid phase at different temperature regions caused the increasing and decreasing of viscosity of the microalgae slurry, respectively. The rheokinetics equations were established based on four-parameter cross-linking rheokinetics equation to describe the variation of viscosity with reaction time in different temperature. The variation of the rheokinetics model parameters with temperature revealed that the temperature has an obviously positive influence on the hydrothermal pretreatment process of the microalgae slurry.

Biotreatment of landfill leachate by microalgae-bacteria consortium in sequencing batch mode and product utilization

Biotreatment of leachate by microalgae-bacteria in a sequencing batch mode using a photobioreactor was investigated. The microalgae-bacteria biomass initial concentration was maintained at 3:1 ratio. The increase in the initial concentration of the biomass in the 2^nd batch favoured biomass growth, doubling biomass productivity, compared to the 1^st batch. In both batches, N-NH₄ was completely removed from the leachate. In the 2^nd batch, the nitrate, COD and phenol removal efficiencies were above 90%. The relative toxicity reduced from 57.32 to 1.12% at the end of 2^nd batch. The fatty acids content (C16-18) varied from 85.47 to 87.65% for the 1^st batch and 86.72 to 87.69% for the 2nd batch. The crude glycerol content varied from 34.54 to 42.36% for the 1^st batch and 33.64 to 39.55% for the 2^nd batch. The coexistence of microalgae and bacteria played an important role in leachate treatment and biomass production for biorefinery purposes.

Hydrodynamic performance of floating photobioreactors driven by wave energy

BACKGROUND

Unlike conventional cultivation systems, liquid mixing in floating photobioreactors (PBRs) is solely induced by their hydrodynamic movement in response to waves, and this movement is affected by the wave conditions (wave height and wave period), the PBR configuration and the culture depth. However, to the best of our knowledge, a practical study of the hydrodynamic movements of PBRs has not been previously conducted.

RESULTS

This study aims to investigate the hydrodynamic performance of floating PBRs in response to wave conditions. First, the effects of the experimental wave height (2-10 cm) and wave period (0.8-1.8 s) on movement was investigated using two 1.0 m2 PBR models: a square PBR (1.0 m/1.0 m; length/width) and a rectangular PBR (1.7 m/0.6 m). The results indicated that wave movement became not only more intense with increasing wave height, but also less intense when the wave period decreased. However, the square PBR experienced more intense movement than the rectangular PBR, but also little mooring force. The effects of culture depth (0.5, 1.0 and 2.0 cm) were investigated and the results showed that the culture depth significantly affected the hydrodynamic movements of the PBRs; however, the mooring forces were unaffected. Finally, the movement and mooring-line forces of PBRs equipped with different mooring systems were investigated. The use of two different mooring systems had little effect on PBR movement; however, a mooring system with floaters was able to significantly reduce the mooring line forces compared to a system without floaters. During this study, the greatest force (10.5 N) was found for the rectangular PBR using a mooring system without floaters, whereas the lowest force (0.67 N) was observed for a rectangular PBR using a mooring system with floaters.

CONCLUSIONS

These studies have provided basic data describing the fluid dynamics of floating PBRs; as well as their structural design and scale up. These results also provide guidance for the selection of ocean fields with suitable wave conditions; as well as a proper mooring methods to ensure safe operation.