Production and characterization of lignin and cellulose fractions obtained from pretreated vine shoots by microwave assisted alkali treatment

Optimization and characterization of reinforced biodegradable cellulose-based aerogels via polylactic acid/polyhydroxybutyrate coating

Vine shoots (VS) and waste eucalyptus paperboard (EP) have been used as cellulose sources (in the form of cellulose nanocrystals -CNCs- and cellulosic fibers respectively) for developing cellulose-based aerogels. Two different parameters including cellulose concentration (0.5 % and 2 % w/v) and freezing temperatures (-20 °C and -80 °C) were tested to evaluate differences in the porosity of the aerogels via Brunauer-Emmett-Teller (BET) and thermal conductivity analyses. In addition, a supplementary coating was applied to the raw aerogels by means of dipping the materials in either polylactic acid (PLA) or polyhydroxybutyrate (PHB) solutions (1 % w/v). Their microstructure was observed via SEM and the reinforcing capacity provided by the coating was measured by means of mechanical compressive tests (~10-fold improvement) and water resistance (contact angle >100°). Finally, aerogels' biodegradability was also confirmed according to the standard ISO 20200 thus providing a sustainable and high-performance alternative to conventional materials also following circular economy principles.

Obtaining of a rich-cellulose material from black wattle (Acacia mearnsii De Wild.) bark residues

Black wattle (Acacia mearnsii De Wild.) barks are residues produced by tannin industries in huge quantities, which are normally discharged on environmental or used for energy production. Therefore, this study aimed to evaluate the use of black wattle bark residues as a raw material on obtaining of a rich-cellulose material by alkaline (MET1), acetosolv (MET2), and organosolv (MET3) procedures. The results obtained indicated that the alkaline methodology, followed by a bleaching step (MET1), promoted klason lignin and hemicellulose removals more efficiently. It was possible to observe that better results were achieved using NaOH concentration of 6% (wt%), at 65 °C for 2.5 h, presenting a yield of 63.24 ± 1.25%, and a reduction on klason lignin content of almost 90.45%. Regarding the bleaching step, it was possible to obtain a material free of non-cellulosic compounds with a yield of 78.28 ± 1.48%. Thermogravimetric analysis indicated the removal of lignin and hemicellulose as well as an increase in cellulose degradation temperature, due to changes in crystalline phases. According to X-ray diffraction (XRD), the procedures employed have led to an increase in crystallinity from 66.27 to 91.78% due to the removal of non-cellulosic compounds. Scanning electron microscopy (SEM) showed morphological alterations in accordance with the removal of non-cellulosic compounds.

Role of hydrothermal pretreatment towards sustainable biorefinery

Recently, the world is experiencing a shift from petroleum refineries to biorefineries due to fossil fuel depletion and environmental concerns. To achieve sustainable development of biorefineries and other components of the biofuel production process, eco-friendly and cost-effective approaches are necessary. Therefore, lignocellulosic biomass (LCB) must be exploited in biorefineries for the generation of a broad spectrum of products. The complex structure of LCB prevents its direct saccharification by enzymatic means, so pretreatment is necessary. There are several pretreatment technologies for disrupting the lignocellulosic structure, but hydrothermal pretreatment is the leading pretreatment technology for recovering hemicellulose fraction with a low number of inhibitors and an increased amount of cellulose. The severity of hydrothermal pretreatment plays a principal role in affecting cellulose, hemicellulose, and lignin structure. A detailed account of microwave-assisted hydrothermal pretreatment technologies and the cost-effectiveness, eco-friendliness, and upcoming challenges of this technology for commercialization with the probable solution is presented.

Woodchip-sulfur based mixotrophic biotechnology for hexavalent chromium detoxification in the groundwater

This study investigated groundwater hexavalent chromium (Cr(VI)) decontamination by a biological permeable reactive barrier (bio-PRB), where a woodchip-elemental sulfur [S(0)] based mixotrophic process was established. 89.0 ± 0.27% of Cr(VI) was removed from the synthetic groundwater after 72 h at a concentration of 50 mg/L during the preliminary batch experiment. The impact of geochemical and hydrodynamic conditions Cr(VI) removal was investigated in the bio-PRB over 225 days. Although elevated Cr(VI) (i.e., 75 mg/L), addition of nitrate and short hydraulic retention time reduced the Cr(VI) removal, 87.2 ± 2.09% of Cr(VI) removal was accomplished. Characterization of the solids indicated that the soluble Cr(VI) was converted and immobilized as the insoluble trivalent chromium [Cr(III)]. 16S rRNA gene based sequencing results suggested that micromolecules produced by woodchip cellulose hydrolyzing- and sulfur oxidizing bacteria were further used by functional Cr(VI) removal bacteria (e.g., Geobacteraceae and Pseudomonas). The extracellular protein and humic-like substances in extracellular polymeric substances (EPS) can bind toxic Cr(VI) through carboxyl and hydroxyl groups, and reduce Cr(VI) in an enzymatic manner. The preliminary finding of this study provided a potential way to utilize agricultural waste for in-situ Cr(VI) contaminated-groundwater remediation.

Cross-Linked Carboxymethylcellulose Adsorbtion Membranes from Ziziphus lotus for the Removal of Organic Dye Pollutants

The goal of this study is to assess Ziziphus lotus's potential for producing carboxymethylcellulose adsorption membranes with the ability to adsorb methyl green from wastewaters by the revalorization of its cellulosic fraction. The cellulose from this feedstock was extracted by an alkaline process and TAPPI standard technique T 203 cm-99 and afterwards they were carboxymethylated. The obtained carboxymethylcelluloses were deeply characterized, being observed that the carboxymethylcellulose produced from the alkaline cellulose presented the higher solubility due to its lower crystallinity degree (53.31 vs. 59.4%) and its higher substitution degree (0.85 vs. 0.74). This carboxymethylcellulose was cross-linked with citric acid in an aqueous treatment in order to form an adsorption membrane. The citric acid provided rigidity to the membrane and although it was hydrophilic it was not soluble in water. By evaluating the potential of the produced membrane for the removal of pollutant dyes from wastewater, it was observed that the adsorption membrane prepared from the carboxymethylcellulose's produced from the Ziziphus lotus was able to remove 99% of the dye, methyl green, present in the wastewater. Thus, this work demonstrates the potential of the Ziziphus lotus for the production of a novel and cost-effective carboxymethylcellulose adsorption membrane with high capacity to treat wastewaters.

Cellulosic Ethanol Production Using Waste Wheat Stillage after Microwave-Assisted Hydrotropic Pretreatment

One of the key elements influencing the efficiency of cellulosic ethanol production is the effective pretreatment of lignocellulosic biomass. The aim of the study was to evaluate the effect of microwave-assisted pretreatment of wheat stillage in the presence of sodium cumene sulphonate (NaCS) hydrotrope used for the production of second-generation bioethanol. As a result of microwave pretreatment, the composition of the wheat stillage biomass changed significantly when compared with the raw material used, before treatment. Microwave-assisted pretreatment with NaCS effectively reduced the lignin content and hemicellulose, making cellulose the dominant component of biomass, which accounted for 42.91 ± 0.10%. In post pretreatment, changes in biomass composition were also visible on FTIR spectra. The peaks of functional groups and bonds characteristic of lignins (C-O vibration in the syringyl ring, asymmetric bending in CH₃, and aromatic skeleton C-C stretching) decreased. The pretreatment of the analyzed lignocellulosic raw material with NaCS resulted in the complete conversion of glucose to ethanol after 48 h of the process, with yield (in relation to the theoretical one) of above 91%. The highest observed concentration of ethanol, 23.57 ± 0.10 g/L, indicated the high effectiveness of the method used for the pretreatment of wheat stillage that did not require additional nutrient supplementation.

Effect of alkaline and deep eutectic solvents pretreatments on the recovery of lignin with antioxidant activity from grape stalks

Grape stalks are lignocellulosic residues that can be valorized through the extraction of lignin - an underutilized biopolymer with high potential. Two lignin extraction methods, alkaline and deep eutectic solvents (DES), were studied, and experimental designs were carried out to obtain the best extraction conditions. The defined parameters for alkaline extraction allowed the recovery of ~48 % of lignin with low purity that was further improved with an autohydrolysis pretreatment (~79 % purity; ~32 % yield). Optimum parameters of DES method rendered high purity lignin (~90 %) without the need of a pretreatment and with a better yield (50.2 % (±2.3)) than the alkaline method. Both lignin fractions presented high antioxidant activities, being close to the antioxidant capacity of BHT for DPPH scavenging. Structural analysis proved the presence of lignin in both alkaline and DES samples with similar morphology. Overall, DES method was more efficient in the extraction of lignin from grape stalks besides its greener and sustainable nature. This work is uses DES to extract lignin from this biomass while comparing it with a commonly classical method, proving that grape stalks can be used to extract lignin with a sustainable and efficient method rendering a final ingredient with value-added properties.

Direct conversion of almond waste into value-added liquids using carbon-neutral catalysts: Hydrothermal hydrogenation of almond hulls over a Ru/CNF catalyst

The almond industry leaves behind substantial amounts of by-products, with almond hulls being the primary residue generated. Given that one way to improve food security is by decreasing waste to reduce environmental impacts, developing sustainable processes to manage this by-product is necessary. Herein, we report on the hydrothermal hydrogenation of almond hulls over a carbon-neutral Ru supported on carbon nanofibres (Ru/CNF) catalyst, addressing the temperature, H₂ pressure, time and catalyst loading. These variables controlled the distribution of the reaction products: gas (0-5%), liquid (49-82%) and solid (13-51%), and ruled the composition of the liquid effluent. This aqueous fraction comprised oligomers (46-81 wt%), saccharides (2-7 wt%), sugar alcohols (2-15 wt%), polyhydric alcohols (1-8 wt%) and carboxylic acids (7-31 wt%). The temperature and reaction time influenced the extension of hydrolysis, depolymerisation, deamination, hydrolysis, hydrogenation and dehydration reactions. Additionally, the initial H₂ pressure and catalyst loading kinetically promoted these transformations, whose extensions were ruled by the amount of H₂ effectively dissolved in the reaction medium and the prevalence of hydrogenations over dehydration/decarboxylation reactions or vice versa depending on the catalyst loading. Process optimisation revealed that it is feasible to convert up to 67% of almond hulls into merchantable oligomers at 230 °C, 35 bar initial H₂, using 1 g catalyst/g biomass (0.4 g Ru/g biomass) for 360 min. Additionally, decreasing the temperature to 187 °C without modifying the other parameters could convert this material into oligomers (31 wt%) and small oxygenates (17 wt% carboxylic acids, 11 wt% sugar alcohols and 6 wt% polyhydric alcohols) concurrently. The theoretical energy assessment revealed that the total and partial combustion of the spent solid material could provide the required energy for the process and allow catalyst recovery and reutilisation. This environmental friendliness and holistic features exemplify a landmark step-change to valorising unavoidable food waste.

Effect of Ammonia Fiber Expansion Combined with NaOH Pretreatment on the Resource Efficiency of Herbaceous and Woody Lignocellulosic Biomass

The most essential issue facing the world today is the provision of energy and sustainable consumption of natural resources. Pretreatment is an essential step to produce biofuels from lignocellulosic biomass. In this study, ammonia fiber explosion (AFEX) combined with NaOH (A-NaOH) pretreatment effects on the characteristics of Pennisetum sinese (herbaceous), oak (hardwood), and camphor wood (softwood) were assessed using enzymatic efficiency analysis, thereby identifying the composition properties of subsequent bio-H₂ production. The results show that the lignin removal (84.2%, 59.7%, and 36.7%, respectively) at 5%A-NaOH conditions and enzymatic efficiency (36.2%, 9.7%, and 6.5%, respectively) of Pennisetum sinese (P. sinese), oak, and camphor wood were significantly increased under 4% A-NaOH conditions. Further A-NaOH pretreatment significantly promoted dark fermentation bio-H₂ production (152.3, 99.1, and 76.9 mL/g TS, respectively) and volatile acid production (4660.2, 3720.2, and 3496.2 mg/L, respectively) of P. sinese, oak, and camphor wood. These findings show that A-NaOH pretreatment is an effective means of utilization of lignocellulose resources.

Algal biomass valorisation to high-value chemicals and bioproducts: Recent advances, opportunities and challenges

Algae are considered promising biomass resources for biofuel production. However, some arguments doubt the economical and energetical feasibility of algal cultivation, harvesting, and conversion processes. Beyond biofuel, value-added bioproducts can be generated via algae conversion, which would enhance the economic feasibility of algal biorefineries. This review primarily focuses on valuable chemical and bioproduct production from algae. The methods for effective recovery of valuable algae components, and their applications are summarized. The potential routes for the conversion of lipids, carbohydrates, and proteins to valuable chemicals and bioproducts are assessed from recent studies. In addition, this review proposes the following challenges for future algal biorefineries: (1) utilization of naturally grown algae instead of cultivated algae; (2) fractionation of algae to individual components towards high-selectivity products; (3) avoidance of humin formation from algal carbohydrate conversion; (4) development of strategies for algal protein utilisation; and (5) development of efficient processes for commercialization and industrialization.

Microwave assisted carbonization and activation of biochar for energy-environment nexus: A review

Conventional thermochemical conversion techniques for biofuel production from lignocellulosic biomass is often non-selective and energy inefficient. Microwave assisted pyrolysis (MAP) is cost and energy-efficient technology aimed for value-added bioproducts recovery from biomass with less environmental impacts. The present review emphasizes the performance of MAP in terms of product yield, characteristics and energy consumption and further it compares it with conventional pyrolysis. The significant role of biochar as catalyst in microwave pyrolysis for enhancing the product selectivity and quality, and the influence of microwave activation on product composition identified through sophisticated techniques has been highlighted. Besides, the application of MAP based biochar as soil conditioner and heavy metal immobilization has been illustrated. MAP accomplished at low temperature creates uniform thermal gradient than conventional mode, thereby producing engineered char with hotspots that could be used as catalysts for gasification, energy storage, etc. The stability, nutrient content, surface properties and adsorption capacity of biochar was enhanced by microwave activation, thus facilitating its use as soil conditioner. Many reviews until now on MAP mostly dealt with operational conditions and product yield with limited focus on comparative energy consumption with conventional mode, analytical techniques for product characterization and end application especially concerning agriculture. Thus, the present review adds on to the current state of art on microwave assisted pyrolysis covering all-round aspects of production followed by characterization and applications as soil amendment for increasing crop productivity in addition to the production of value-added chemicals, thus promoting process sustainability in energy and environment nexus.

Efficient utilization of Iris pseudacorus biomass for nitrogen removal in constructed wetlands: Combining alkali treatment

Aquatic plant biomass like Iris pseudacorus can be used as electron donor to improve denitrification performance in subsurface constructed wetlands. However, the phenomenon that the nitrogen removal rate declined in the terminal stage restricted the utilization of litters. In terms of this problem, this study investigated the performance of the used biomass through alkali treatment on nitrogen removal and analyzed the effect of alkali treatment on the component and structure of biomass and microbial community. The results showed that the alkali-treated biomass could further enhance the nitrogen removal by nearly 15% compared with used ones. The significant damage of cell walls and compact fibers containing cellulose and lignin through alkali treatment mainly resulted in the improvement of carbon release and nitrogen removal. With the addition of alkali-treated biomass, the richness index of microbes was higher compared with other biomass materials. Furthermore, the abundance of denitrification related genera increased and the abundance of genera for nitrification was maintained. Based on these finds, a mode of a more efficient Iris pseudacorus self-consumed subsurface flow constructed wetlands was designed. In this mode, the effluent total nitrogen could be stabilized below 5 mg L^-1 for nine months and the weight of litters could be further cut down by 75%. These findings would contribute to efficient utilization of plant biomass for nitrogen removal enhancement and final residue reduction in the wetlands.

Structural changes of lignin-carbohydrate complexes (LCCs) from Chinese quince fruits during the sequential fractionation of pectic and hemicellulosic polysaccharides

Chinese quince (Chaenomeles sinensis) fruits offer a potential source of pectin and hemicellulose. However, the existence of lignin-carbohydrate complexes (LCCs) can negatively impact the extraction of pectin and hemicellulose. In this work, LCCs were sequentially fractionated from Chinese quince during the removal of pectin and hemicellulose. The structures of LCCs were characterized by HPAEC, FT-IR, GPC, Py-GC/MS, TGA and 2D HSQC NMR. The results showed that the carbohydrate content and molecular weight of LCCs was found to be changed significantly after the removal of hemicellulose (KSH). The lignin in Björkman LCCs was found to be linked mainly to galactan and fructan, whereas the lignin LCC-AcOHs was found to be linked mainly to arabinan after the removal of KSH. The isolation of carbonate-soluble pectin (NSP) increased thermal stability of Björkman LCC fraction, however, the isolation of chelator-soluble pectin (CSP) increased the thermal stability of LCC-AcOHs. The S/G ratios of LCC-AcOHs increased and large amounts of S-type lignin released during sequential fractionation of pectin and hemicellulose. These results will be beneficial for understanding the mechanisms of pectin and hemicellulose isolation, thereby facilitating the potential application of Chinese quince as a valuable natural resource for food and other industries.

Biologically removing vanadium(V) from groundwater by agricultural biomass

Vanadium (V) in groundwater can pose a serious threat on both environment and health. Agricultural biomass contains solid carbon source (SCS) and could be attractive for biologically removing V(V). For this purpose, cypress sawdust, corn cob and wheat straw were selected as SCSs to remove vanadate (NaVO₃). The experiments demonstrated a high efficiency of V(V) up to 98.6%, and the anaerobically biological reduction of V(V) to V(IV) by wheat straw was identified to be the best SCS by the spectrum analysis of XRD and FTIR. Along with increasing the fragment size of wheat straw, the V(V)-removal efficiency decreased, and the fragment size down to 1-3 mm was confirmed to have a significant bio-removal performance on V(V). Based on the analysis of 16s rRNA sequencing, the microbial abundance and diversity increased in the suspension liquid in the end, indicating that the microbial community could tolerate and/or detoxify V(V), besides degrading lignocellulosic materials.

Microwave-assisted hydrotropic pretreatment as a new and highly efficient way to cellulosic ethanol production from maize distillery stillage

Abstract

Aim of the study was to assess the suitability of the combined use of microwave radiation and sodium cumene sulfonate under optimized process conditions for the preparation of maize stillage biomass as a raw material for the production of cellulosic ethanol. The key parameter guaranteeing a high level of lignin removal from biomass (ca. 44%) was concentration of hydrotrope. Even at high biomass concentration (16% w/v) and a cellulase enzyme dose of about 4 filter-paper units/g, maize stillage biomass subjected to microwave-assisted hydrotropic pretreatment was highly susceptible to enzymatic degradation, which resulted in 80% hydrolysis yield. It is possible to obtain a fermentation medium with a very high glucose concentration (up to 80 g/L), without fermentation inhibitors and, as a consequence, to reach a very high level of sugar conversion to ethanol (concentration above 40 g/L), even as much as 95% of theoretical yield. Microwave hydrotropic treatment with sodium cumene sulfonate is a very effective way to prepare waste maize stillage biomass for the production of cellulosic ethanol. The degradation of the lignocellulose structure by the simultaneous use of microwaves and hydrotropes ensured a high degree of conversion of structural polysaccharides to bioethanol. The method provides a high level of enzymatic degradation of cellulose, leading to a medium with high content of released sugars suitable for bioconversion, which is in line with assumptions of the second-generation ethanol production technology.

Key points

• Microwave-assisted hydrotropic pretreatment is a new way to cellulosic ethanol production.

• Microwave-assisted hydrotropic delignification removes 44% of lignin from biomass.

• No fermentation inhibitors are obtained after microwave-assisted hydrotropic pretreatment.

• High ethanol concentration (above 40 g/L) and fermentation yield (95% of theoretical yield) from biomass after microwave-assisted hydrotropic pretreatment.

Enzymatic conversion of pretreated lignocellulosic biomass: A review on influence of structural changes of lignin

The demands of energy sustainability drive efforts to bio-chemical conversion of biomass into biofuels through pretreatment, enzymatic hydrolysis, and microbial fermentation. Pretreatment leads to significant structural changes of the complex lignin polymer that affect yield and productivity of the enzymatic conversion of lignocellulosic biomass. Structural changes of lignin after pretreatment include functional groups, inter unit linkages and compositions. These changes influence non-productive adsorption of enzyme on lignin through hydrophobic interaction and electrostatic interaction as well as hydrogen bonding. This paper reviews the relationships between structural changes of lignin and enzymatic hydrolysis of pretreated lignocellulosic biomass. The formation of pseudo-lignin during dilute acid pretreatment is revealed, and their negative effect on enzymatic hydrolysis is discussed.

Revealing the structural characteristics of lignin macromolecules from perennial ryegrass during different integrated treatments

To reveal the structural characteristics and physicochemical properties of perennial ryegrass lignin, sequential alkali extractions or double ball-milling and enzymatic hydrolysis on the basis of ultrasonic and hydrothermal pretreatments were proposed in this study. Results revealed that sequential alkali extractions released 89.4% of original lignin from the ryegrass cell walls and 0.75-4.16% of associated carbohydrates as compared to the double ball-milling and enzymatic hydrolysis (96.0% and 18.39%). It was observed that the two types of lignin prepared were SGH-type and had different amounts of p-coumarates and ferulates, and primarily consisted of β-O-4' linkages combined with minor amounts of β-β' and β-5' linkages. Besides, alkali-soluble lignins exhibited relatively fewer β-O-4' linkages, higher S/G ratios and H-type units, and abundant phenolic OH groups as compared to the double enzymatic lignin. Overall, the deeper investigation of the lignin structure of ryegrass will provide useful information for the efficient utilization of lignin macromolecules in biorefineries.

Microwave-assisted alkali hydrolysis for cellulose isolation from wheat straw: Influence of reaction conditions and non-thermal effects of microwave

Microwave-assisted hydrolysis has been widely studied for cellulose fiber isolation, but the influence of reaction conditions and the microwave non-thermal effect are not well clarified. In this study, a series of well-designed experiments were carried out to measure the effects of reaction conditions including temperature, duration and alkali concentration. Compared to the other parameters, temperature was more relevant to the cellulose content in fiber. It could reach the maximum purity of 90.66 % when the temperature was up to 140 °C. Moreover, the existence of non-thermal effect of microwave has been confirmed through extensive determination and characterization of the fibers obtained from parallel controlled experiments conducted with or without microwave assistance. Approximately 50 %-75 % reduction in reaction time or 67 % of that in chemical costs would be realized under microwave with respect to traditional heating hydrolysis. Therefore, this work provides both deep insight and efficiency strategy into the microwave-assisted cellulose isolation.

Bioethanol Production from Vineyard Waste by Autohydrolysis Pretreatment and Chlorite Delignification via Simultaneous Saccharification and Fermentation

In this paper, the production of a second-generation bioethanol from lignocellulosic vineyard cutting wastes was investigated in order to define the optimal operating conditions of the autohydrolysis pretreatment, chlorite delignification and simultaneous saccharification and fermentation (SSF). The autohydrolysis of vine-shoot wastes resulted in liquors containing mainly a mixture of monosaccharides, degradation products and spent solids (rich in cellulose and lignin), with potential utility in obtaining valuable chemicals and bioethanol. The autohydrolysis of the vine-shoot wastes was carried out at 165 and 180 °C for 10 min residence time, and the resulted solid and liquid phases composition were analysed. The resulted liquid fraction contained hemicellulosic sugars as a mixture of alpha (α) and beta (β) sugar anomers, and secondary by-products. The solid fraction was delignified using the sodium chlorite method for the separation of lignin and easier access of enzymes to the cellulosic sugars, and then, converted to ethanol by the SSF process. The maximum bioethanol production (6%) was obtained by autohydrolysis (165 °C), chlorite delignification and SSF process at 37 °C, 10% solid loading, 72 h. The principal component analysis was used to identify the main parameters that influence the chemical compositions of vine-shoot waste for different varieties.

Recovery of Natural Antioxidants from Agro-Industrial Side Streams through Advanced Extraction Techniques

Large amounts of agro-industrial waste are being generated each year, leading to pollution and economic loss. At the same time, these side streams are rich source of active compounds including antioxidants. Recovered compounds can be re-utilized as food additives, functional foods, nutra-/pharmaceuticals, cosmeceuticals, beauty products, and bio-packaging. Advanced extraction techniques are promising tools to recover target compounds such as antioxidants from agro-industrial side streams. Due to the disadvantages of classical extraction techniques (such as large amounts of solvents, increased time of extraction, large amounts of remaining waste after the extraction procedure, etc.), and advanced techniques emerged, in order to obtain more efficient and sustainable processes. In this review paper aspects regarding different modern extraction techniques related to recovery of antioxidant compounds from wastes generated in different industries and their applications are briefly discussed.