Nutrient recovery from wastewater: From technology to economy

Integrating renewable energy in sewage sludge treatment through greenhouse solar drying: A review

Sewage sludge is the main by-product of wastewater treatment plants, requiring significant environmental and economic burdens for its management and disposal. Recently, solar drying processes, often performed through solar greenhouses, received interest due to their limited energy requirement and renewable energy exploitation. The dried sludge shows significant volume and mass reductions, reducing transportation and disposal costs. However, its physicochemical and microbiological characteristics must be properly assessed, especially if agricultural reuse is the final sludge destination, due to the possible accumulation of (micro)pollutants in the soil. This review depicts the state-of-the-art solar drying processes of sewage sludge, with a focus on the technological aspects and the sludge quality. The review discusses greenhouse-specific features, sludge composition (organic matter, pathogens, heavy metals and emerging pollutants) and drying conditions (seasonality, ventilation, sludge mixing and thickness, and drying speed). The economic aspects connected to sludge solar drying are presented. The limitations of this technology are discussed as well, including the limited applicability to wet sludge and the environmental issues connected to greenhouse structure degradation. A wider application of sludge solar drying is recommended to increase the sustainability of small and medium wastewater treatment plants, especially in areas with high amounts of solar radiation and dry weather conditions, while thermal drying still appears preferable for large plants. More agronomic studies must be conducted to assess the possible pollutant accumulation in crops, and alternative uses of the dried sludge (e.g., energy recovery through incineration, pyrolysis or gasification; utilization in construction materials) should be explored, also using life cycle assessment.

The use of ammonia recovered from wastewater as a zero-carbon energy vector to decarbonise heat, power and transport - A review

Ammonia (NH3) is an energy vector with an emerging role in decarbonising heat, power and transport through its direct use as a fuel, or indirectly as a hydrogen carrier. Global ammonia production is having to grow to enable the exploitation of NH3 for energy decarbonisation, which it is projected will consume >50 % of manufacturing capacity by 2050. Ammonia recovered from wastewater can be directly exploited as a sustainable source of ammonia, to reduce the demand for ammonia produced through the energy intensive Haber-Bosch process, while fostering a triple carbon benefit to the water sector, by: (i) avoiding the energy required for aeration of biological processes; (ii) reducing nitrous oxide emissions associated with ammonia oxidation, which is a potent greenhouse gas; and (iii) producing a zero-carbon energy source that can decarbonise energy use. While previous reviews have described technologies relevant for ammonia recovery, to produce ammonia as a zero-carbon fuel or hydrogen carrier, wastewater ammonia must be transformed into the relevant concentration, phase and achieve the product quality demanded for zero carbon heat, power and transport applications, which are distinct from those demanded for more conventional exploitation routes (e.g. agricultural). This review therefore presents a synthesis of established and emerging technologies for the extraction and concentration of ammonia from wastewater, with specific emphasis on enabling the production of ammonia in a form that can be directly exploited for zero carbon energy generation. A précis of technologies for the valorisation of ammonia as a clean energy or hydrogen resource is also introduced, together with discussion of their relevancy and applicability to the water sector including implications to energy, carbon emissions and financial return. The exploitation of ammonia recovered from wastewater as a zero carbon energy source is shown to offer a critical contemporary response for the water sector that seeks to rapidly decarbonise existing infrastructure, while responding to ever stricter nitrogen discharge limits.

Enhancing the cultivation of Salicornia fruticosa with agroindustrial compost leachates in a cascade cropping system: evaluating the impact of melatonin application

Cascade cropping systems (CCS) utilize leachate from a primary crop to grow secondary crops and enhance the efficient use of water and fertilizers in areas with scarce water resources. A preliminary study investigated the effect of melatonin in a cascade cropping system to potentially improve plant tolerance to abiotic stresses. This study aimed to cultivate Salicornia fruticosa in this cropping system to reduce nutrient discharge and assess the impact of exogenous melatonin on Salicornia growth and quality. The CCS included a primary crop of Salicornia grown in an agro-industrial compost or peat. Leachates from these media were used to cultivate the same plant once again in a floating system under four treatments: compost leachate (T1), peat leachate (T2), 100% nutrient solution (NS) (T3), 50% NS (T4) strength. Four concentrations of exogenous melatonin were applied in foliar spray: 0, 100, 200, and 400 µM. Melatonin application increased yield, with the highest values observed when plants were grown in T1. Water use efficiency was also maximized in T1 and with both 200 and 400 µM melatonin applications. The highest nitrogen use efficiency was achieved in plants grown in peat leachate. The lipid membrane damage was assessed revealing that plants grown in compost leachate exhibited the lowest MDA values regardless of melatonin concentrations. The accumulation of some antinutritional compounds (nitrate, oxalate, and sodium) were the highest in those plants grown in compost leachate. Overall, shoots grown in peat leachate exhibited the best phytochemical profile (total phenol content, total flavonoids, and antioxidant capacity), with peak values in plants treated with 200 µM melatonin. These findings suggest that S. fruticosa can be effectively cultivated using leachate from a previous crop in a floating system and that exogenous melatonin application enhances the yield and nutritional quality of Salicornia shoots.

Comparative performance of Populus spp. and Salix spp. for growth, nutrition, and heavy metal uptake in a wastewater hydroponic system

This research aimed to ascertain the growth, biomass, and phytoremediation capacity of poplars and willow cultivated using wastewater in a hydroponic system. The cuttings were exposed to two water treatments for eight weeks: (1) tap water supply with 1/4 strength Hoagland's solution (TW) as a control and (2) urban raw wastewater with 1/4 strength Hoagland's solution (WW) in a completely randomized experimental design and growth parameters and nutrient and heavy metal content distribution in various plant tissues were assessed. Our results suggest that compared with the TW, seven studied species/clones revealed an increase in growth and biomass parameters (stem height by 16.4%, and root, shoot, and total biomass by 37.3%, 26.9%, and 29.3%, respectively) caused by WW treatment, except the root length and stem diameter that remained the same under two water treatments. Poplars and willow showed a remarkable variability in growth and biomass parameters, with the highest stem diameter, stem height, and root, shoot, and total biomass in Populus nigra L. 62.154. Expression of growth responses to WW treatment with tolerance indices (Tis) indicated the tested poplars and willow as highly tolerant (Ti >100%) with no significant differences among them based on this index. Plant analysis showed that WW treatment increased the concentrations of nutrients and heavy metals in the shoots and roots. Overall, under both water treatments, the capability of the tested species/clones to uptake and accumulate micro-nutrients (except copper (Cu) in shoots) and heavy metals (except chromium (Cr) in shoots) in the plant tissues varied noticeably. However, for all tested plants, the roots had higher concentrations of micro-nutrients (iron (Fe), zinc (Zn), and Cu concentrations in the roots were about 36.8%, 107.6%, and 30.1% of that in the shoots, respectively) and heavy metals (nickel (Ni), Cr, and lead (Pb) concentrations in the roots were about 115.3%, 344.2%, and 198.9% of that in the shoots, respectively), suggesting their capability for micro-nutrients and heavy metals rhizofiltration. Concerning obtained results under hydroponic culture, it can be concluded that these poplars and willow might be promising candidates for wastewater applications. However, data obtained by a hydroponic system need to be confirmed in pot and field experiments.

Environmental sustainability opportunity and socio-economic cost analyses of phosphorus recovery from sewage sludge

Although phosphorus (P) recovery and management from sewage sludge are practiced in North America and Europe, such practices are not yet to be implemented in China. Here, we evaluated the environmental sustainability opportunity and socio-economic costs of recovering P from sewage sludge by replacing the current-day treatments (CT; sludge treatment and landfill) and P chemical fertilizer application (CF) in China using life cycle assessment and life cycle costing methods. Three potential P recovery scenarios (PR1‒PR3: struvite, vivianite, and treated sludge) and corresponding current-day scenarios (CT1‒CT3 and CF) were considered. Results indicated that PR1 and PR2 have smaller environmental impacts than the current-day scenarios, whereas PR3 has larger impacts in most categories. PR3 has the lowest net costs (sum of internal costs and benefits, 39.1-54.7 CNY per kg P), whereas PR2 has the lowest external costs (366.8 CNY per kg P). Societal costs for production and land use of 1 kg P by P recovery from sewage sludge (e.g., ∼527 CNY for PR1) are much higher than those of P chemical fertilizers (∼20 CNY for CF). However, considering the costs in the current-day treatments (e.g., ∼524 CNY for CT1), societal costs of P recovery scenarios are close to or slightly lower than those of current-day scenarios. Among the three P recovery scenarios, we found that recovering struvite as P fertilizer has the highest societal feasibility. This study will provide valuable information for improved sewage sludge management and will help promote the sustainable supply of P in China.

Sewage sludge pretreatment: current status and future prospects

Sewage sludge is regarded by wastewater treatment plants as problematic, from a financial and managerial point of view. Thus, a variety of disposal routes are used, but the most popular is methane fermentation. The proportion of macromolecular compounds in sewage sludges varies, and substrates treated in methane fermentation provide different amounts of biogas with various quality and quantity. Depending on the equipment and financial capabilities for methane fermentation, different methods of sewage sludge pretreatment are available. This review presents the challenges associated with the recalcitrant structure of sewage sludge and the presence of process inhibitors. We also examined the diverse methods of sewage sludge pretreatment that increase methane yield. Moreover, in the field of biological sewage sludge treatment, three future study propositions are proposed: improved pretreatment of sewage sludge using biological methods, assess the changes in microbial consortia caused with pretreatment methods, and verification of microbial impact on biomass degradation.

Examining current trends and future outlook of bio-electrochemical systems (BES) for nutrient conversion and recovery: an overview

Nutrient-rich waste streams from domestic and industrial sources and the increasing application of synthetic fertilizers have resulted in a huge-scale influx of reactive nitrogen and phosphorus in the environment. The higher concentrations of these pollutants induce eutrophication and foster degradation of aquatic biodiversity. Besides, phosphorus being non-renewable resource is under the risk of rapid depletion. Hence, recovery and reuse of the phosphorus and nitrogen are necessary. Over the years, nutrient recovery, low-carbon energy, and sustainable bioremediation of wastewater have received significant interest. The conventional wastewater treatment technologies have higher energy demand and nutrient removal entails a major cost in the treatment process. For these issues, bio-electrochemical system (BES) has been considered as sustainable and environment friendly wastewater treatment technologies that utilize the energy contained in the wastewater so as to recovery nutrients and purify wastewater. Therefore, this article comprehensively focuses and critically analyzes the potential sources of nutrients, working mechanism of BES, and different nutrient recovery strategies to unlock the upscaling opportunities. Also, economic analysis was done to understand the technical feasibility and potential market value of recovered nutrients. Hence, this review article will be useful in establishing waste management policies and framework along with development of advanced configurations with major emphasis on nutrient recovery rather than removal from the waste stream.

Valorization of Anaerobic-Fermentation Liquid Digestates-Membrane-Based Process Development

Complete valorization of various wastes and effluents, with significant organic content, remains a great challenge in the pursuit of a circular economy. The approach based on anaerobic fermentation, leading to valuable biogas production, has been broadly accepted and employed as an attractive processing scheme. However, despite notable research efforts, complete valorization of the digestates (involving recovery of nutrients/by-products and full recycling/reuse of treated water) requires additional work for sustainable process development. This study aims to make a contribution in this direction by demonstrating a systematic methodology for valorizing the liquid digestate. The proposed membrane-based processing scheme involves UF-membrane pretreatment of the liquid digestate (for sludge separation) and subsequent NF/RO membrane treatment for reuse/recycling of the permeate; the concentrate, enriched in "nutrients" (phosphate and ammonium compounds), can be utilized for soil fertilization, with further conditioning/processing. By performing targeted laboratory experiments and advanced simulations, the membrane-based process was developed to a relatively high technology-readiness level, including a pilot unit design/construction and preliminary testing with satisfactory results. Through pilot testing in industrial environment, further process development and optimization will be pursued, towards practical applications. The demonstrated methodology is also considered appropriate for systematic development of membrane-based processes to valorize/treat a variety of similar effluents.

Direct Membrane Filtration of Municipal Wastewater: Studying the Most Suitable Conditions for Minimizing Fouling Rate in Commercial Porous Membranes at Demonstration Scale

This study aimed to evaluate the feasibility of applying a commercial porous membrane to direct filtration of municipal wastewater. The effects of membrane pore size (MF and UF), treated influent (raw wastewater and the primary settler effluent of a municipal wastewater treatment plant) and operating solids concentration (about 1 and 2.6 g L^-1) were evaluated on a demonstration plant. Filtration periods of 2-8 h were achieved when using the MF membrane, while these increased to 34-69 days with the UF membrane. This wide difference was due to severe fouling when operating the MF membrane, which was dramatically reduced by the UF membrane. Use of raw wastewater and higher solids concentration showed a significant benefit in the filtration performance when using the UF module. The physical fouling control strategies tested (air sparging and backwashing) proved to be ineffective in controlling UF membrane fouling, although these strategies had a significant impact on MF membrane fouling, extending the operating period from some hours to 5-6 days. The fouling evaluation showed that a cake layer seemed to be the predominant reversible fouling mechanism during each independent filtration cycle. However, as continuous filtration advanced, a large accumulation of irreversible fouling appeared, which could have been related to intermediate/complete pore blocking in the case of the MF membrane, while it could have been produced by standard pore blocking in the case of the UF membrane. Organic matter represented more than 70% of this irreversible fouling in all the experimental conditions evaluated.

Enhanced bioenergy and nutrients recovery from wastewater using hybrid anodes in microbial nutrient recovery system

Background

The combined microbial fuel cell–microbial nutrient recovery system has lately been thoroughly explored from an engineering standpoint. The relevance of microbial communities in this process, on the other hand, has been widely underestimated.

Results

A lab-scale microbial nutrients recovery system was created in this work, and the microbial community structure was further defined, to give a thorough insight into the important microbial groups in the present system. We reported for the first-time different hybrid anodes of activated carbon and chitosan that were used in the microbial nutrient recovery system for bioenergy production, and, for the removal of COD and recovery of nutrients present in the wastewater. The hybrid anodic materials were studied to adapt electrochemically active bacteria for the recovery of nutrients and energy generation from wastewater without the need for an external source of electricity. The potential of the created hybrid anodes in terms of nutrients recovery, chemical oxygen demand elimination, and energy generation from municipal wastewater was thoroughly examined and compared with each other under similar operating conditions. When the COD loading was 718 mg/L, a total COD removal of ~ 79.2% was achieved with a hybrid activated carbon and chitosan anode having an equal ratio after 10 days of the operation cycle. The maximum power density estimated for hybrid anode (~ 870 mWm⁻²) was found.

Conclusion

Overall, this work reveals a schematic self-driven way for the collection and enrichment of nutrients (~ 72.9% phosphorus recovery and ~ 73% ammonium recovery) from municipal wastewater, as well as consistent voltage production throughout the operation.

Supplementary Information

The online version contains supplementary material available at 10.1186/s13068-022-02116-y.

From waste to fertilizer: Nutrient recovery from wastewater by pristine and engineered biochars

Biochar application for the recovery of nutrients from wastewater is a sustainable method based on a circular economy. Wastewater, food wastewater, and stormwater are valuable sources of nutrients (i.e., PO₄^3-, NO₃^-, and NH₄⁺). The unique properties of biochar, such as its large specific surface area, pH buffering capacity, and ion-exchange ability, make it a cost-effective and environmentally friendly adsorbent. Biochar engineering improves biochar properties and provide targeted adsorbents. The biochar-based fertilizers can be a sustainable alternative to traditional fertilization. The aim of the study was to compare the potential of pristine and engineered biochars to recover nutrients from wastewater and to determine the factors which may affect this process. Engineered biochar can be used as a selective adsorbent from multicomponent solutions. Adsorption on engineered biochar can be also regulated by additional mechanisms: surface precipitation and ligand/ion exchange. Metal modification (e.g. Mg, Fe) enhances PO₄^3- and NO₃^- adsorption capacity, and thus may provide the extra plant macro-/micronutrients. The desorption mechanism, which is the basis for nutrient release are strongly pH depended. The use of biochar-based fertilizer can have economic and agricultural benefits when using waste materials and reducing pyrolysis energy costs.

An Insight into Microbial Inoculants for Bioconversion of Waste Biomass into Sustainable "Bio-Organic" Fertilizers: A Bibliometric Analysis and Systematic Literature Review

The plant-microbe holobiont has garnered considerable attention in recent years, highlighting its importance as an ecological unit. Similarly, manipulation of the microbial entities involved in the rhizospheric microbiome for sustainable agriculture has also been in the limelight, generating several commercial bioformulations to enhance crop yield and pest resistance. These bioformulations were termed biofertilizers, with the consistent existence and evolution of different types. However, an emerging area of interest has recently focused on the application of these microorganisms for waste valorization and the production of "bio-organic" fertilizers as a result. In this study, we performed a bibliometric analysis and systematic review of the literature retrieved from Scopus and Web of Science to determine the type of microbial inoculants used for the bioconversion of waste into "bio-organic" fertilizers. The Bacillus, Acidothiobacillus species, cyanobacterial biomass species, Aspergillus sp. and Trichoderma sp. were identified to be consistently used for the recovery of nutrients and bioconversion of wastes used for the promotion of plant growth. Cyanobacterial strains were used predominantly for wastewater treatment, while Bacillus, Acidothiobacillus, and Aspergillus were used on a wide variety of wastes such as sawdust, agricultural waste, poultry bone meal, crustacean shell waste, food waste, and wastewater treatment plant (WWTP) sewage sludge ash. Several bioconversion strategies were observed such as submerged fermentation, solid-state fermentation, aerobic composting, granulation with microbiological activation, and biodegradation. Diverse groups of microorganisms (bacteria and fungi) with different enzymatic functionalities such as chitinolysis, lignocellulolytic, and proteolysis, in addition to their plant growth promoting properties being explored as a consortium for application as an inoculum waste bioconversion to fertilizers. Combining the efficiency of such functional and compatible microbial species for efficient bioconversion as well as higher plant growth and crop yield is an enticing opportunity for "bio-organic" fertilizer research.

Investigation of the effect of nitrification inhibition on the performance and effluent quality of aerobic sequential batch reactors

The use of nitrification inhibition as a concentrating step for ammonium (NH₄⁺), for the purpose of increasing the potential for simultaneous recovery of phosphate (PO₄^3-) and NH₄⁺ from effluent streams of an aerobic sequencing batch reactor (SBR) system, has never been investigated in the literature. Therefore, the present study aimed to determine the effect of the inhibition of nitrification on both the reactor performance and effluent quality in a laboratory scale aerobic SBR system. In order to compare the observed results, a separate reactor, where the inhibition was not applied, was operated as a control reactor (CR) under the identical operational conditions used for the inhibitory reactor (IR). Experimental results for the reactor performance showed that effluents with low total suspended solids (< 50 mg/L) and chemical oxygen demand concentrations (> 90% of removal efficiency based on the influent concentration of 500 mg/L) were achieved for both SBRs by obtaining an activated sludge with a sludge volume index < 60 mL/g after the acclimation period. In the same period, the effluent PO₄^3-, NH₄⁺, and nitrate (NO₃^-) concentrations were found to be 17.0 ± 4.0, 1.26 ± 0.84, and 21.5 ± 39 mg/L for the CR and 10.0 ± 4.4, 3.9 ± 2.4, and 9.2 ± 1.5 mg/L for the IR, respectively. During this period, 94% of the removed NH₄⁺ (NH₄⁺_rem.) was converted to NO₃^- in the CR, indicating almost complete nitrification occurred in the reactor. However, only 47% of the NH₄⁺_rem. was converted to NO₃^- in the IR as a result of the inhibition of nitrification, meaning a partial inhibition (53%) occurred due to the inhibition treatment. These results clearly demonstrated that the inhibition of nitrification allowed the effluent NH₄⁺ concentrations to increase by suppressing the formation of NO₃^- ions. Based on the results, it can be concluded that inhibition of nitrification in an aerobic SBR system creates a potential for conserving the effluent NH₄⁺ concentration and increasing consecutive recovery of PO₄^3- together with NH₄⁺ from the effluent discharges.

Technical advances on current research trends and explore the future scope on nutrient recovery from waste-streams: a review and bibliometric analysis from 2000 to 2020

An exponentially growing global population has led to an increase in nutrient pollution in different aqueous bodies. Although different processes have successfully removed nutrients from wastewater on a large scale, a limited number of studies have been reported on efficiency, cost-effectiveness, and future potential of physical, chemical, and biological nutrient recovery methods to overcome the depletion of natural resources. Therefore, researchers need to understand current research trends by applying different approaches to investigate higher efficient nutrient recovery technologies. In this article, the research patterns and in-depth review of various nutrient recovery processes have been circumscribed with the application of bibliometric and attractive index (AAI) vs. activity index (AI) analysis. The performance, advantages, limitations, and future prospects of different nutrient recovery methods have also been addressed. More than 70% of study publications were published in the last decade in chemical and biological processes, which might be related to more rigorous effluent quality rules and increasing water pollution. The future prediction in the field of nutrient recovery has been predicted using S-curve analysis, and it was found that the number of publications in the saturated state in chemical methods was highest. However, the growth rate of the biological-based nutrient recovery methods is greater, which may be because of their huge research scope, cost-effectiveness, and easy operation methods. This study can assist researchers in understanding the current research scenario in nutrient recovery techniques and provide the research scope in nutrient recovery from wastewater in the future.

Phytoremediation Potential of Selected Ornamental Woody Species to Heavy Metal Accumulation in Response to Long-Term Irrigation with Treated Wastewater

Arid and semiarid environments of Mediterranean countries suffer from scarcity of water resources, which limits their agriculture productivity. Using treated wastewater (TWW) is considered an alternative strategy for irrigation purposes in such areas. However, TWW contains substantial levels of heavy metals (HMs) and contaminants that pollute the environment and soil. The aim of this study is to evaluate the phytoremediation potential of six selected woody tree species under long-term irrigation with TWW. The concentration, bioaccumulation factor (BFC), translocation factor (TF), and comprehensive bioconcentration index (CBCI) of HMs were measured in the various parts (roots, bark, and leaves) of the studied tree species. The results show a general pattern of mineral accumulation in the roots and low translocation to the areal parts of various species. Cupressus sempervirens, which is a native species in Mediterranean environments, had higher TF values for Fe, Mn, Cu, Cr, Cd, and Pb metals in its areal parts compared to other tree species. The study shows that Ficus nitida has the potential to be a hyperaccumulator for Cd in its bark, with a TF value that exceeds 12. Deciduous trees species (Populus nigra and Robinia pseudoacacia) were found to have high TF values for Ni and Cd toward their areal parts, whereas a higher TF for Cr (1.21) was only found in P. nigra bark. Cupressus sempervirens had, significantly, the highest bark and leaf CBCI values (0.83 and 0.82, respectively), whereas Ficus nitida had the second-highest values in the bark and leaves (0.56 and 0.51, respectively). Therefore, Cupressus sempervirens and Ficus nitida are considered good hyperaccumulators for various HMs, and can be used for phytoremediation activities in polluted areas.

Effect of Treated Wastewater Irrigation on the Accumulation and Transfer of Heavy Metals in Lemon Trees Cultivated in Arid Environment

The Middle East is considered as one of the driest regions of the world and the use of municipal-treated wastewater (TWW) for agricultural purposes is needed. The aim of this study was to evaluate the effect of continuous irrigation of TWW in lemon orchards on the accumulation of heavy metals (HMs) in the soil, as well as their uptake and translocation to aerial parts of the trees. For this purpose, two lemon orchards were selected to be irrigated from two different water sources: TWW from a tertiary treatment plant and freshwater (SW) from Moses springs in Jordan. Continuous irrigation with TWW resulted in higher concentrations of nutrients and HM accumulation in the soil as compared to SW. However, HM accumulation in the soil was found to be within the acceptable range according to the standards of the WHO. On the contrary, the continuous irrigation with TWW resulted in the accumulation of HMs in plant parts when compared to SW irrigation; the fruits were clearly affected by the accumulation of high levels of Cd and Pb that exceed the maximum limits for the presence of HMs in plant tissues. The irrigation of lemon trees with TWW had a significant effect on the bioaccumulation factor and translocation factors (TF) of HMs into different lemon tree parts. Heavy metal accumulation coincided with high translocation rates to different tree parts, and this is considered to be a main challenge for long-term irrigation with TWW in arid environments.

Valorisation of residues from municipal wastewater sieving through anaerobic (co-)digestion with biological sludge

The Circular and Green Economy principles is inspiring new approaches to municipal wastewater treatment plants (MWWTPs) design and operation. Recently, an ever-growing interest is devoted to exploring the alternatives for switching the WWTPs from being able to 'simply' removing contaminants from water to biorefinery-like plants where energy and material can be recovered. In this perspective, both wastewater and residues from process can be valorised for recovering nutrients (N and P), producing value added products (i.e. biopolymers), energy vectors and biofuels (i.e. bio-H₂, bio-CH₄ and bioethanol). As an additional benefit, changing the approach for WWTPs design and operation will decrease the overall amount of landfilled residues. In this context, the present research is aimed at evaluating the CH₄ production potential of MWW screening units' residues. While such a stream is typically landfilled, the expected progressive increase of biodegradable matter content due to the ban on single-use plastic along with the boost of bioplastics makes the investigation of different biochemical valorisation routes more and more interesting from an environmental and economical perspective. Thus, a full-scale data collection campaign was performed to gain information on screening residues amount and properties and to analyse the relationship with influent flowrate. The most relevant residue properties were measured, and lab-scale tests were carried out to evaluate the bio-CH₄ potential.

Wastewater Purification with Nutrient and Carbon Recovery in a Mobile Resource Container

Water reuse from wastewater treatment plants can significantly reduce freshwater demand. Additionally municipal sewage and some industrial wastewaters could be used as sources of nutrients and carbon more effectively than they are used today. Biological treatments have attracted the most attention in wastewater purification, whereas, so far, only a little attention has been paid to the physico-chemical technologies. These technologies could, however, have great potential to recover nutrients when purifying wastewater. In this study, the main emphasis was to study the possibilities to utilize existing physico-chemical unit operations for wastewater purification and nutrients as well as carbon recovery. Unit operations were selected so that they could produce exploitable circular economy products from wastewaters and be assembled in a mobile container for carrying out recovery anywhere that is suitable. The results showed that in a mobile container, solids could be successfully separated from the studied wastewaters by flocculation-assisted solid/liquid separation and then processed into hydrochar by hydrothermal carbonization. Phosphate was precipitated using lime milk as calcium phosphate, and ammonium nitrogen was captured from the wastewater using membrane contactor technology resulting in ammonium sulphate for fertilizer use. Additionally, reverse osmosis retained residual impurities well, producing good quality water for reuse. The techno-economic feasibility seems promising.

Exploiting the Nutrient Potential of Anaerobically Digested Sewage Sludge: A Review

The world is currently witnessing a rapid increase in sewage sludge (SS) production, due to the increased demand for wastewater treatment. Therefore, SS management is crucial for the economic and environmental sustainability of wastewater treatment plants. The recovery of nutrients from SS has been identified as a fundamental step to enable the transition from a linear to a circular economy, turning SS into an economic and sustainable source of materials. SS is often treated via anaerobic digestion, to pursue energy recovery via biogas generation. Anaerobically digested sewage sludge (ADS) is a valuable source of organic matter and nutrients, and significant advances have been made in recent years in methods and technologies for nutrient recovery from ADS. The purpose of this study is to provide a comprehensive overview, describing the advantages and drawbacks of the available and emerging technologies for recovery of nitrogen (N), phosphorus (P), and potassium (K) from ADS. This work critically reviews the established and novel technologies, which are classified by their ability to recover a specific nutrient (ammonia stripping) or to allow the simultaneous recovery of multiple elements (struvite precipitation, ion exchange, membrane technologies, and thermal treatments). This study compares the described technologies in terms of nutrient recovery efficiency, capital, and operational costs, as well as their feasibility for full-scale application, revealing the current state of the art and future perspectives on this topic.

Water Resource Recovery Facilities (WRRFs): The Case Study of Palermo University (Italy)

The wastewater sector paradigm is shifting from wastewater treatment to resource recovery. In addition, concerns regarding sustainability during the operation have increased. In this sense, there is a need to break barriers (i.e., social, economic, technological, legal, etc.) for moving forward towards water resource recovery facilities and demonstration case studies can be very effective and insightful. This paper presents a new water resource recovery case study which is part of the Horizon 2020 EU Project “Achieving wider uptake of water-smart solutions—Wider Uptake”. The final aim is to demonstrate the importance of a resource recovery system based on the circular economy concept. The recovery facilities at Palermo University (Italy) are first presented. Afterwards, the resource recovery pilot plants are described. Preliminary results have underlined the great potential of the wastewater treatment plant in terms of resources recovery and the central role of the University in fostering the transition towards circular economy. The fermentation batch test highlighted a volatile fatty acids (VFAs) accumulation suitable for polyhydroxyalkanoates (PHAs) production. The results of static adsorption and desorption tests showed that the highest amount of adsorbed NH4+ was recorded for untreated and HCl-Na treated clinoptilolite.

Challenges and opportunities for more efficient water use and circular wastewater management. The case of Campania Region, Italy

By 2050, global demand for water is expected to increase by some 55% due to population growth and urbanization. The utilization of large amounts of freshwater in the world, generate huge volumes of wastewater of which, globally, more than 80% is discharged without treatment, thus causing impacts on aquatic ecosystems, human health and economic productivity. More sustainable practices of wastewater management are expected as a way towards circular bioeconomy (CBE) processes, whose goal is to implement closed systems promoting the systematic use of recycling, reuse and recovery of bioproducts and by-products and the reduction of waste generation. This approach, if adopted in the water and wastewater sector, can ensure environmental, economic and social benefits. The reuse of wastewater, on the one hand, reduces the volume of wastewater and the pressure on water bodies; on the other hand, the recovery of nutrients (P or N) and/or other high value bioproducts (biogas, cellulose, biopolymers) from wastewater offers numerous advantages in terms of supplying new raw bio-based materials that can be refed back to supply chains (thus substituting fossil resources) and, at the same time, producing cleaner water to be reused. Nevertheless, while in Europe many industries have demonstrated the ability to recycle and reuse water, in many regions of Italy the sustainable management of water and wastewater is not yet consolidated. In this study we explore the available technological, economic and environmental options concerning water use and wastewater treatment and we apply them to design appropriate scenarios for improved use efficiency and circular management. A comprehensive literature review of the most promising wastewater treatment processes for resources and energy valorization was conducted. The recovery of PHAs, struvite, nitrogen and algal biomass, as potential substitutes for conventional PET, phosphate and nitrogen chemical fertilizers and electricity, respectively, in addition to reusable treated water, were hypothesized and carefully discussed. Resulting scenarios are tested against the present situation of Campania Region (situated in Southern Italy) based on population and demand statistics, in order to develop strategies and policies potentially applicable locally and elsewhere.

Wastewater Refinery: Producing Multiple Valuable Outputs from Wastewater

A wastewater refinery is a multifunctional solution that combines different technologies and processing schemes to recover a spectrum of valuable materials from municipal or industrial wastewater. The concept of wastewater refinery introduces a new perspective on wastewater treatment and management. It aims at making the most of wastewater constituents by co-producing different worthful outputs, such as water, energy, nitrogen, sulfide, and phosphorous. This can turn the treatment of wastewater from a major cost into a source of profit. The wastewater refinery approach is well aligned with the concept of the circular economy. A case study on Qatar’s wastewater revealed the potential recovery of significant quantities of valuable resources embodied in the country’s wastewater. Valorization of organic constituents and the recovery of nitrogen, phosphorus, and sulfide should be given priority. To facilitate the adoption of the wastewater refinery concept, research is required to explore technical and economic bottlenecks.

Bio-membrane based integrated systems for nitrogen recovery in wastewater treatment: Current applications and future perspectives

Nitrogen removal is crucial in wastewater treatment process as excessive nitrogen content could result in eutrophication and degradation of aquatic ecosystems. Moreover, to satisfy the fast-growing need of fertilizers due to an increase in human population, recovering nitrogen from wastewater is of the most sustainable approach. Currently, the membrane technique integrated with biological processes namely bio-membrane based integrated system (BMIS) is a promising technology for recovering nitrogen from wastewater, including osmotic membrane bioreactors, bioelectrochemical systems and membrane photobioreactors. In this review study, the nitrogen recovery in different BMHSs, the role of operational parameters and the nitrogen recovery mechanism were discussed. Apart from this, the implementation of nitrogen recovery at pilot- and full-scale was summarized. Perspectives on the major challenges and recommendations of the BMIS for the nitrogen recovery in wastewater treatment were proposed, in which the integrated technologies and more scale-up studies regarding nitrogen recovery by the BMISs were also highlighted and recommended.

A Framework for Sustainable Planning and Decision-Making on Resource Recovery from Wastewater: Showcase for São Paulo Megacity

Currently, it is important to develop strategic frameworks to support the selection of sustainable resource recovery solutions. This study applies a new framework for planning, implementation, and assessment of resource recovery strategies for a full-scale wastewater treatment plant (WWTP) in São Paulo megacity. The framework comprises several steps based on case study-specific data and information from current literature. Data were collected from various sources: a survey with a wastewater treatment utility, national and regional databases, and review of local regulations and international literature. Treatment configuration, wastewater and by-products composition, potential demand (for water, energy, and phosphorus), stakeholder identification, and local legislation were thoroughly discussed regarding decision-making on resource recovery. Scenario analysis was used to explore suitable nutrient and energy recovery measures based on indicators. Biogas recovery and sewage sludge composting showed more favorable conditions due to similar experiences in the area and robust legislation. The proposed framework is a simplified tool, and its application can support managers to get information on resource recovery and how to plan such initiatives in easier ways to facilitate wiser decision-making, and better operation and management. The results on framework use and refinement can guide potential applications in other contexts and stimulate public policy formulation and further research.

Multi-period evaluation and selection of rural wastewater treatment technologies: a case study

Rapid population growth and agricultural development are generating a considerable amount of effluents, which poses threats to the quality of rural water resources as well as sanitary conditions. However, with a range of rural wastewater treatment (WT) technologies available, one major problem facing the practitioners is which to choose as the most favorable option suited to specific areas. In this study, a novel decision-making framework is proposed to evaluate and select the optimal alternative in rural areas of Xi'an within multiple consecutive time periods. Firstly, an evaluation index system is constructed and picture fuzzy numbers (PFNs) are used to represent both evaluation levels and experts' refusal due to limitation of knowledge. Secondly, fuzzy analytical hierarchy process (FAHP) is applied to derive weights of criteria, which enables experts to assign fuzzy numbers to express their preferences for comparison judgments. Thirdly, evidence theory is utilized to obtain the aggregated values from multiple time periods. Finally, based on the belief intervals obtained, sequencing batch reactor (A₄) is determined as the optimal rural WT technology in Xi'an from 2006 to 2020, whereas the membrane bio-reactor (A₂) is the last option. The effectiveness of the proposed framework is further validated by comparative analysis. This research can hopefully serve as useful guidance for the assessment of rural WT technologies in various regions.