Microplastics contamination in water supply system and treatment processes

Due to global demand, millions of tons of plastics have been widely consumed, resulting in the widespread entry of vast amounts of microplastic particles into the environment. The presence of microplastics (MPs) in water supplies, including bottled water, has undergone systematic review, assessing the potential impacts of MPs on humans through exposure assessment. The main challenges associated with current technologies lie in their ability to effectively treat and completely remove MPs from drinking and supply water. While the risks posed by MPs upon entering the human body have not yet been fully revealed, there is a predicted certainty of negative impacts. This review encompasses a range of current technologies, spanning from basic to advanced treatments and varying in scale. However, given the frequent detection of MPs in drinking and bottled water, it becomes imperative to implement comprehensive management strategies to address this issue effectively. Consequently, integrating current technologies with management options such as life-cycle assessment, circular economy principles, and machine learning is crucial to eliminating this pervasive problem.

Deseasonalized trend of ground-level ozone and its precursors in an industrial city Kaohsiung, Taiwan

Mitigating ground-level ozone (GLO) remains challenging due to its highly nonlinear formation process. Thus, understanding GLO pollution trends is crucial for developing effective control strategies, especially Kaohsiung industrial city, Taiwan. Based on the long-term monitoring data set of 2011-2022, temporal analysis reveals that monthly mean GLO peaks in autumn (40.66 ± 5.10 ppb), carbon monoxide and major precursors such as nitrogen oxides , nonmethane hydrocarbons reach their highest levels in winter. The distinct seasonal variation of air pollutants in Kaohsiung is primarily influenced by the unique blocking effect of the mountainous area under the northeasterly wind, as the city is situated downwind, causing high GLO levels during autumn due to the accumulation of stagnant air hindering the dispersion of pollutants. Over the 12 years (2011-2022), the deseasonalized trend analysis was conducted with p < 0.001, revealing a stabilization trend of GLO (+0.04 ppb/yr) from a previous sharp increase. The observed improvement is credited to a drastic decrease in total oxidants () at -0.63 ppb/yr due to significantly reducing their precursors. Furthermore, the effectiveness of precursor reduction is also supported by GLO daily maximum profile changes. While high GLO events (>120 ppb) decrease, days within midrange (60-80 ppb) rise from 24.4% to 33.3%. A notable difference emerges when comparing daytime and nighttime GLO. While daytime GLO decreased at -0.22 ppb/yr, nighttime GLO increased at +0.34 ppb/yr. Weakened nocturnal titration effects accounted for the nighttime increase. The distinct spatial variations in GLO trends on a citywide scale underscore that areas with complicated industrial activities may not benefit from a continuing reduction of precursors compared to less-polluted areas. The findings of this study hold significant implications for improving GLO control strategies in heavily industrialized city and provide valuable information to the general public about the current state of GLO pollution.

KHCO3-activated high surface area biochar derived from brown algae: A case study for efficient adsorption of Cr(VI) in aqueous solution

The current study aimed to assess the effectiveness of biochar formed from algae in the removal of Cr(VI) through the process of impregnating brown algae Sargassum hemiphyllum with KHCO3. The synthesis of KHCO3-activated biochar (KBAB-3), demonstrating remarkable adsorption capabilities for Cr(VI), was accomplished utilizing a mixture of brown algae and KHCO3 in a mass ratio of 1:3, followed by calcination at a temperature of 700 °C. Based on the empirical evidence, it can be observed that KBAB-3 shown a significant ability to adsorb Cr(VI) within a range of 60-160 mg g-1 across different environmental conditions. In addition, the KBAB-3 material demonstrated the advantageous characteristic of easy separation, allowing for the continued maintenance of a high efficiency in removing Cr(VI) even after undergoing numerous cycles of reuse. In conclusion, the application of KBAB-3, a novel adsorbent, exhibits considerable prospects for effective removal of Cr(VI) from diverse water sources in the near future.

Occurrence and fate of pharmaceutical pollutants in wastewater: Insights on ecotoxicity, health risk, and state-of-the-art removal

Pharmaceutical active compound (PhAC) residues are considered an emerging micropollutant that enters the aquatic environment and causes harmful ecotoxicity. The significant sources of PhACs in the environment include the pharmaceutical industry, hospital streams, and agricultural wastes (animal husbandry). Recent investigations demonstrated that wastewater treatment plants (WWTPs) are an important source of PhACs discharging ecosystems. Several commonly reported that PhACs are detected in a range level from ng L-1 to μg L-1 concentration in WWTP effluents. These compounds can have acute and chronic adverse impacts on natural wildlife, including flora and fauna. The approaches for PhAC removals in WWTPs include bioremediation, adsorption (e.g., biochar, chitosan, and graphene), and advanced oxidation processes (AOPs). Overall, adsorption and AOPs can effectively remove PhACs from wastewater aided by oxidizing radicals. Heterogeneous photocatalysis has also proved to be a sustainable solution. Bioremediation approaches such as membrane bioreactors (MBRs), constructed wetlands (CWs), and microalgal-based systems were applied to minimize pharmaceutical pollution. Noteworthy, applying MBRs has illustrated high removal efficiencies of up to 99%, promising prospective future. However, WWTPs should be combined with advanced solutions, e.g., AOPs/photodegradation, microalgae-bacteria consortia, etc., to treat and minimize their accumulation. More effective and novel technologies (e.g., new generation bioremediation) for PhAC degradation must be investigated and specially designed for a low-cost and full-scale. Investigating green and eco-friendly PhACs with advantages, e.g., low persistence, no bioaccumulation, less or non-toxicity, and environmentally friendly, is also necessary.

Bacterial community composition in a two-stage anaerobic membrane bioreactor for co-digestion of food waste and food court wastewater

This study investigated the microbial community of a two-stage anaerobic membrane bioreactor (2S-AnMBR) co-digesting food waste and food court wastewater. The hydrolysis reactor (HR) was dominated by Bacteroidetes and Firmicutes phylum, with genus Lactobacillus enriched due to food waste fermentation. The up-flow anaerobic sludge blanket (UASB) was dominated by genus such as Methanobacterium and Methanosaeta. The presence of Methanobacterium (91 %) and Methanosaeta (7.5 %) suggested that methane production pathways inevitably undergo both hydrogenotrophic and acetoclastic methanogenesis. Hydrogen generated during hydrolysis fermentation in the HR contributed to methane production in the UASB via hydrogenotrophic pathways. However, the low abundance of Methanosaeta in the UASB can be attributed to the limited inffluent of volatile fatty acids (VFA) and the competitive presence of acetate-consuming bacteria Acinetobacter. The UASB exhibited more excellent dispersion and diversity of metabolic pathways compared to the HR, indicating efficient methane production.

Influence of salinity on microalgae-bacteria symbiosis treating shrimp farming wastewater

Shrimp farming has strongly developed in recent years, and became an important economic sector that helps create jobs and increase incomes for Vietnamese. However, the aquatic environment has also been greatly affected by the development due to the amount of wastewater discharged from shrimp farms. Among biological processes used for treating shrimp farming wastewater, the application of microalgae-bacteria co-culture is considered high potential due to its treatment and energy saving. Consequently, a photobioreactor operated with microalgae-bacteria co-culture was employed to treat shrimp farming wastewater. The salinity of wastewater and the operating condition (ratio of biomass retention time and hydraulic retention time, BRT/HRT) are the major factors affecting pollutant removal. Thus, this study investigated the effects of salinities of 0.5-20 ppt and BRT/HRT ratios of 1.5-16 on the removal performance. The results indicated that the nutrient removal was reduced when PBR operated under salinity over than 10 ppt and BRT/HRT over 5.5. Particularly, the nitrogen and phosphorus removal rates were achieved 6.56 ± 1.33 gN m-3 d-1 and 1.49 ± 0.59 gP m-3 d-1, and the removal rates decreased by 2-4 times under a salinity >10 ppt and 2-6 times under a BRT/HRT ratio >5.5. Whereas, organic matter treatment seems not to be affected when the removal rate was maintained at 28-34 gCOD m-3 d-1 under various conditions.

Emission characteristics of naphthalene from ship exhausts under global sulfur cap

The global sulfur limit regulation mandates the use of 0.5 % low sulfur fuel oil (LSFO) to reduce emissions of sulfur oxides (SOx), nitrogen oxides (NOx), and particulate matter (PM). However, the addition of naphthalene (Nap) to LSFO to stabilize its quality has led to an increase in polycyclic aromatic hydrocarbons (PAHs), with Nap being the main pollutant. This study investigates the effects of Nap in ship exhaust by analyzing the emission concentrations of volatile organic compounds (VOCs) and Nap in the exhaust of 16 ships, including 2 container ships, 6 bulk carriers, 1 tanker, 2 ferries, 3 fishing vessels, and 2 harbor crafts, based on USEPA method TO-15A. The results show that the percentage of Nap emissions in the exhaust gases of the 16 ship engines ranged from 77 % to 97 % of the total volatile organic compound (TVOC). The Nap concentration in the exhaust of fishing vessels, tanker, and harbor craft exceeded the occupational exposure limit of 50,000 μg/m3, with fishing vessels having the highest TVOC and Nap concentrations. The enhanced Nap emission in the air degrades air quality in port cities and poses an obvious potential public health risk. While the benefits of the global sulfur cap are being secured, additional efforts should be made to reduce the undetected side effects. Alternative stabilizers of LSFO should be considered, or Nap emission control should be boosted to mitigate the potential negative impact on harbor air quality.

A review of biosensor for environmental monitoring: principle, application, and corresponding achievement of sustainable development goals

Human health/socioeconomic development is closely correlated to environmental pollution, highlighting the need to monitor contaminants in the real environment with reliable devices such as biosensors. Recently, variety of biosensors gained high attention and employed as in-situ application, in real-time, and cost-effective analytical tools for healthy environment. For continuous environmental monitoring, it is necessary for portable, cost-effective, quick, and flexible biosensing devices. These benefits of the biosensor strategy are related to the Sustainable Development Goals (SDGs) established by the United Nations (UN), especially with reference to clean water and sources of energy. However, the relationship between SDGs and biosensor application for environmental monitoring is not well understood. In addition, some limitations and challenges might hinder the biosensor application on environmental monitoring. Herein, we reviewed the different types of biosensors, principle and applications, and their correlation with SDG 6, 12, 13, 14, and 15 as a reference for related authorities and administrators to consider. In this review, biosensors for different pollutants such as heavy metals and organics were documented. The present study highlights the application of biosensor for achieving SDGs. Current advantages and future research aspects are summarized in this paper.Abbreviations: ATP: Adenosine triphosphate; BOD: Biological oxygen demand; COD: Chemical oxygen demand; Cu-TCPP: Cu-porphyrin; DNA: Deoxyribonucleic acid; EDCs: Endocrine disrupting chemicals; EPA: U.S. Environmental Protection Agency; Fc-HPNs: Ferrocene (Fc)-based hollow polymeric nanospheres; Fe₃O₄@3D-GO: Fe₃O₄@three-dimensional graphene oxide; GC: Gas chromatography; GCE: Glassy carbon electrode; GFP: Green fluorescent protein; GHGs: Greenhouse gases; HPLC: High performance liquid chromatography; ICP-MS: Inductively coupled plasma mass spectrometry; ITO: Indium tin oxide; LAS: Linear alkylbenzene sulfonate; LIG: Laser-induced graphene; LOD: Limit of detection; ME: Magnetoelastic; MFC: Microbial fuel cell; MIP: Molecular imprinting polymers; MWCNT: Multi-walled carbon nanotube; MXC: Microbial electrochemical cell-based; NA: Nucleic acid; OBP: Odorant binding protein; OPs: Organophosphorus; PAHs: Polycyclic aromatic hydrocarbons; PBBs: Polybrominated biphenyls; PBDEs: Polybrominated diphenyl ethers; PCBs: Polychlorinated biphenyls; PGE: Polycrystalline gold electrode; photoMFC: photosynthetic MFC; POPs: Persistent organic pollutants; rGO: Reduced graphene oxide; RNA: Ribonucleic acid; SDGs: Sustainable Development Goals; SERS: Surface enhancement Raman spectrum; SPGE: Screen-printed gold electrode; SPR: Surface plasmon resonance; SWCNTs: single-walled carbon nanotubes; TCPP: Tetrakis (4-carboxyphenyl) porphyrin; TIRF: Total internal reflection fluorescence; TIRF: Total internal reflection fluorescence; TOL: Toluene-catabolic; TPHs: Total petroleum hydrocarbons; UN: United Nations; VOCs: Volatile organic compounds.

Pilot and full scale applications of floating treatment wetlands for treating diffuse pollution

Floating treatment wetlands (FTW) are nature-based solutions for the purification of open water systems such as rivers, ponds, and lakes polluted by diffuse sources as untreated or partially treated domestic wastewater and agricultural run-off. Compared with other physicochemical and biological technologies, FTW is a technology with low-cost, simple configuration, easy to operate; has a relatively high efficiency, and is energy-saving, and aesthetic. Water remediation in FTWs is supported by plant uptake and the growth of a biofilm on the water plant roots, so the selection of the macrophyte species is critical, not only to pollutant removal but also to the local ecosystem integrity, especially for full-scale implementation. The key factors such as buoyant frame/raft, plant growth support media, water depth, seasonal variation, and temperature have a considerable role in the design, operation, maintenance, and pollutant treatment performance of FTW. Harvesting is a necessary process to maintain efficient operation by limiting the re-pollution of plants in the decay phase. Furthermore, the harvested plant biomass can serve as a green source for the recovery of energy and value-added products.

Biochar for soil remediation: A comprehensive review of current research on pollutant removal

Biochar usage in soil remediation has turned out to be an enticing topic recently. Biochar, a product formed by pyrolysis of organic waste, which is rich in carbon, has the aptitude to ameliorate climate change by sequestering carbon while also enhancing soil quality and crop yields. Two-edged implications of biochar on soil amendment are still being discussed yet, clarity on the long-term implications of biochar on soil health and the environment is not yet achieved. As a result, it is crucial to systematically uncover the pertinent information regarding biochar remediation, as this can serve as a roadmap for future research on using biochar to remediate contaminated soils in mining regions. This review endeavors to bring forth run thoroughly the latest state of research on the use of biochar in soil remediation, along with its potential benefits, limitations, challenges, and future scope. By synthesizing existing literature on biochar soil remediation, this review aims to provide insights into the potential of biochar as a sustainable solution for soil remediation. Specifically, this review will highlight the key factors that influence the effectiveness of biochar for soil remediation and the potential risks associated with its use, as well as the current gaps in knowledge and future research directions.

Enhanced biodegradation of endocrine disruptor bisphenol A by food waste composting without bioaugmentation: Analysis of bacterial communities and their relative abundances

Composting with food waste was assessed for its efficacy in decontaminating Bisphenol A (BPA). In a BPA-treated compost pile, the initial concentration of BPA 847 mg kg-1 fell to 6.3 mg kg-1 (99% reduction) over a 45-day composting period. The biodegradation rate was at its highest when bacterial activity peaked in the mesophilic and thermophilic phases. The average rate of total biodegradation was 18.68 mg kg-1 day-1. Standard methods were used to assess physicochemical parameters of the compost matrix and gas chromatography combined with mass spectrometry (GC/MS) was used to identify BPA intermediates. Next-generation sequencing (NGS) was used to detect BPA degraders and the diverse bacterial communities involved in BPA decomposition. These communities were found consist of 12 phyla and 21 genera during the composting process and were most diversified during the maturation phase. Three dominant phyla, Firmicutes, Pseudomonadota, and Bacteroidetes, along with Lactobacillus, Proteus, Bacillus, and Pseudomonas were found to be the most responsible for BPA degradation. Different bacterial communities were found to be involved in the food waste compost biodegradation of BPA at different stages of the composting process. In conclusion, food waste composting can effectively remove BPA, resulting in a safe product. These findings might be used to expand bioremediation technologies to apply to a wide range of pollutants.

Solid waste management techniques powered by in-silico approaches with a special focus on municipal solid waste management: Research trends and challenges

Many technical, climatic, environmental, biological, financial, educational, and regulatory factors are typically involved in solid waste management (SWM). Artificial Intelligence techniques have lately gained attraction in providing alternative computational methods for resolving problems of solid waste management. The purpose of this review is to direct solid waste management researchers taking an interest in the use of artificial intelligence in their area of study via main research elements such as AI models, their own benefits and drawbacks, effectiveness, and applications. The main AI technologies recognized in the survey are analysed and discussed in the subsections of the review, which contains a specific fusion of AI models. It also covers research that equated AI technologies to other non-AI methodologies. The section that follows contains a brief debate of the numerous SWM disciplines where AI was consciously applied. The article concludes with progress, challenges and perspectives in implementing AI-based SWM.

NiCo2O4-loaded sunflower husk-derived biochar as efficient peroxymonosulfate activator for tetracycline removal in water

In this study, biochar produced from sunflower seeds husk was activated through ZnCl₂ to support the NiCo₂O₄ nanoparticles (NiCo₂O₄@ZSF) in catalytic activation of peroxymonosulfate (PMS) toward tetracycline (TC) removal from aqueous solution. The good dispersion of NiCo₂O₄ NPs on the ZSF surface provided sufficient active sites and abundant functional groups for the adsorption and catalytic reaction. The NiCo₂O₄@ZSF activating PMS showed high removal efficiency up to 99% after 30 min under optimal condition ([NiCo₂O₄@ZSF] = 25 mg L^-1, [PMS] = 0.04 mM, [TC] = 0.02 mM and pH = 7). The catalyst also exhibited good adsorption performance with a maximum adsorption capacity of 322.58 mg g^-1. Sulfate radicals (SO₄^•-), superoxide radical (O₂•-), and singlet oxygen (¹O₂) played a decisive role in the NiCo₂O₄@ZSF/PMS system. In conclusion, our research elucidated the production of highly efficient carbon-based catalysts for environmental remediation, and also emphasized the potential application of NiCo₂O₄ doped biochar.

Characterization of reciprocation membrane bioreactor on treatment performance, energy consumption and membrane fouling

Two reciprocating membranes (rMBR) with two frequencies of 0.46 Hz (rMBR-0.46) and 0.3 Hz (rMBR-0.3) were operated to compare the treatment performance and gross energy consumption with a conventional MBR. The average organic removal rates of MBR, rMBR-0.46 and rMBR-0.3 were maintained 295 ± 51; 823 ± 296; and 397 ± 129 mgCOD/gVSS.d, respectively. Nitrogen removal was enhanced in rMBR phases compared to conventional MBR phase due to anoxic membrane chamber. Further, fouling rate was found to be highest of 16.5 mbar/day (at conventional MBR phase), which was and much decreased to1.0 mbar/day (at rMBR-0.46 phase) and then 0.2 mbar/day (rMBR-0.3 phase). The reciprocation membrane also showed energy potential by saving 10.6% electricity for each treated cubic meter of wastewater compared to the conventional MBR.

Roles of microalgae-based biofertilizer in sustainability of green agriculture and food-water-energy security nexus

For years, agrochemical fertilizers have been used in agriculture for crop production. However, intensive utilization of chemical fertilizers is not an ecological and environmental choice since they are destroying soil health and causing an emerging threat to agricultural production on a global scale. Under the circumstances of the increasing utilization of chemical fertilizers, cultivating microalgae to produce biofertilizers would be a wise solution since desired environmental targets will be obtained including (1) replacing chemical fertilizer while improving crop yields and soil health; (2) reducing the harvest of non-renewable elements from limited natural resources for chemical fertilizers production, and (3) mitigating negative influences of climate change through CO₂ capture through microalgae cultivation. Recent improvements in microalgae-derived-biofertilizer-applied agriculture will be summarized in this review article. At last, the recent challenges of applying biofertilizers will be discussed as well as the perspective regarding the concept of circular bio-economy and sustainable development goals (SDGs).

Hydrothermal and pyrolytic conversion of sunflower seed husk into novel porous biochar for efficient adsorption of tetracycline

In this study, sunflower seed husk biochar prepared by ZnCl₂-activated and hydrothermal carbonization (HZSF) was studied for its effectiveness in removing tetracycline (TC) from an aqueous solution. The physical and chemical properties of materials were characterized by different methods of surface analysis. The specific surface area of HZSF is significantly enhanced over 1200 times compared with non-modified biochar (HZSF: 1578.3 m²·g^-1, SF-700: 1.3 m²·g^-1), which has an enhancement effect on the TC adsorption capacity. The HZSF showed that the Langmuir isotherm and pseudo-second-order kinetic models could properly characterize the adsorption processes. In the Langmuir isotherm model, HZSF exhibited effective adsorption performance with q_max of 673.0 mg·g^-1 at 298 K for 24 h. The possible mechanisms for the adsorption process were the monolayer, chemical adsorption, and the participation of strong intermolecular forces. In general, HZSF has the potential to be a useful adsorbent for the elimination of antibiotics from water-based solutions.

Effect of biomass retention time on performance and fouling of a stirred membrane photobioreactor

Co-culture of microalgae-activated sludge has the potential to purify wastewater while reduce energy demand from aeration. In this work, a mechanically stirred membrane photobioreactor (stirred-MPBR) was used to evaluate the impact of the biomass retention time (BRT) on the treatment performance and membrane fouling. Results showed that stirred-MPBR was affected by BRT during treating domestic wastewater at a flux of 16.5 L m^-2 h^-1. The highest productivity was attained at BRT 7d (102 mg L^-1 d^-1), followed by BRT 10d (86 mg L^-1 d^-1), BRT 5d (85 mg L^-1 d^-1), and BRT 3d (83 mg L^-1 d^-1). Statistical analysis results showed that BRT 7d had a higher COD removal rate than BRT 10d, however, there is no difference in total nitrogen removal rate. The highest TP removal occurred when the biomass operated at BRT as short as 3d. Reduced BRTs caused a change in the microalgae-activated sludge biomass fraction that encouraged nitrification activity while simultaneously contributing to a higher fouling rate. The bound protein concentrations dropped from 31.35 mg L^-1 (BRT 10d) to 10.67 mg L^-1 (BRT 3d), while soluble polysaccharides increased from 0.99 to 1.82 mg L^-1, respectively. The concentrations of extracellular polymeric substance fractions were significantly altered, which decreased the mean floc size and contributed to the escalating fouling propensity. At the optimum BRT of 7d, the stirred-MPBR showed sufficient access to light and nutrients exchange for mutualistic interactions between the microalgae and activated sludge.

Phosphoric acid-activated biochar derived from sunflower seed husk: Selective antibiotic adsorption behavior and mechanism

In recent years, the unnecessary overuse of antibiotics has increased globally, resulting in antibiotic contamination of water, which has become a significant environmental concern. This study aims to examine the adsorption behavior of antibiotics (Tetracycline TC, Ciprofloxacin CIP, Ibuprofen IBP, and Sulfamethoxazole SMX) onto H₃PO₄-activated sunflower seed husk biochar (PSF). The results demonstrated that H₃PO₄ could enhance the specific surface area (378.8 m²/g) and create a mesoporous structure of biochar. The adsorption mechanism was investigated using kinetic models, isotherms, and thermodynamics. The maximum adsorption capacities (q_max) of TC, CIP, SMX, and IBP are 429.3, 361.6, 251.3, and 251.1 mg g^-1, respectively. The adsorption mechanism of antibiotics on PSF was governed by complex mechanisms, including chemisorption, external diffusion, and intraparticle diffusion. This research provides an environmentally friendly method for utilizing one of the agricultural wastes for the removal of a variety of antibiotics from the aquatic environment.

Seasonal influence on pollution index and risk of multiple compositions of microplastics in an urban river

Emerging contaminant microplastics (MPs) are getting worldwide attention for their ubiquitous occurrence and potential risk to the environment. However, the seasonal influence on freshwater MP pollution remains poorly understood. To better understand and evaluate the riverine MPs in different seasons, this study conducted the risk assessment of MPs in an urban river, Houjin River, during the different seasons. The present study found that the MPs (0.1-5 mm, mostly 0.1-2 mm) were more abundant in the dry season (183.33 ± 128.95 items/m³) compared with the wet season (102.08 ± 45.80 items/m³). Similarly, the mixture of different MPs polymers was more diverse in the dry season. The related pollution indices such as the contamination factor (CF) and pollution load index (PLI) showed that average CF and PLI were 5.15 and 2.10 in the dry season, which significantly decreased to 1.58 and 1.25, respectively, in the wet season (p < 0.05). Additionally, significant difference of the average risk quotient (RQ) was observed, which was 0.037 in the dry season and 0.021 in the wet season (p < 0.05). To sum up, the results of this study indicate the seasonal effects on the pollution and risk of multiple compositions of MPs in the urban river, suggesting higher impacts of riverine MPs pollution in the dry season, as well as the potential increase of MPs, may lead to environmental risk in the future.

Ecological risk assessment and corrective actions for dioxin-polluted sediment in a chemical plant's brine water storage pond

Despite the known high toxicity of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs, or dioxins), there are few case studies of PCDD/Fs contamination in sediment and there remains much to learn regarding their ecological impact. In this study, we performed an environmental risk assessment of a brine water storage pond near a chemical plant with high PCDD/Fs pollution potential before and after corrective actions. We found PCDD/F accumulation in the pond's fish and crab from the brine water storage pond, and the PCDD/Fs concentrations in biota higher than Taiwan's food safety standard (3.5 pg-TEQ/g). Furthermore, we found a high degree of pollution using different indices, including contamination factor (CF), modified degree of contamination (mCd), and pollution index (PI), in the pond's sediment. Before corrective actions, we also found high risk in the PCDD/F contamination in the sediment using various biological risk indices, including potential ecological risk index (RI) and risk quotient (RQ). After the corrective actions, including institutional/engineering control and remediation, the CF, mCd, and PI had decreased by 20-41 % and RI and RQ by 41-56 %. In addition, despite the slight reduction of pollution and risk index values in the whole pond, significant reduction was observed in the sediment of highly polluted area A owing to the lower disturbing suction dredging. In conclusion, the corrective actions used in this study helped decrease the pollution and ecological risk associated with this site's PCDD/Fs polluted sediment to some extent, suggesting that contamination and risk could be reduced to acceptable levels if these corrective actions are continued.

Removal of heavy metals from aqueous solutions by high performance capacitive deionization process using biochar derived from Sargassum hemiphyllum

Capacitive deionization (CDI) has been considered as an efficient, energy-saving and environmental friendly technology for water treatment. For the practical application of CDI, high-performance electrode materials beyond standard activated carbon should be developed. In this study, biochar derived from brown algae Sargassum hemiphyllum prepared by pyrolysis at 300-700 °C and then used as the CDI electrode to remove Cu(II) from aqueous solutions. According to the findings, the optimal pyrolysis temperature was 700 °C, and the electrosorption capacity of BAB700 was 75-120 mg·g-1 at an applied voltage of 1.2 V across wide range of initial pH, temperatures and ion types. Moreover, BAB700 also exhibited outstanding ability to electrosorb other heavy metals (Zn(II), Ni(II), and Cd(II)). In addition, the BAB700 retained the Cu(II) removal efficiency of 70 % in 10 cycles. Cu(II) in actual water is completely eliminated with great reproducibility, resulting in a high degree of applicability for water treatment.

Biodegradation of high di-(2-Ethylhexyl) phthalate (DEHP) concentration by food waste composting and its toxicity assessment using seed germination test

Di-(2-ethylhexyl) phthalate (DEHP), a plasticizer derived from phthalate ester, is used as an additive in industrial products such as plastics, paints, and medical devices. However, DEHP is known as an endocrine-disrupting chemical, causing cancers and adverse effects on human health. This study evaluated DEHP biodegradation efficiency via food waste composting during 35 days of incubation. At high DEHP concentrations (2167 mg kg^-1) in food waste compost mixture, the DEHP biodegradation efficiency was 99% after 35 days. The highest degradation efficiency was recorded at the thermophilic phase (day 3 - day 11) with the biodegradation rate reached 187 mg kg^-1 day^-1. DEHP was metabolized to dibutyl phthalate (DBP) and dimethyl phthalate (DMP) and would be oxidized to benzyl alcohol (BA) and mineralized into CO₂ and water via various metabolisms. Finally, the compost's quality with residual DEHP was evaluated using Brassica chinensis L. seeds via 96 h of germination tests. The compost (at day 35) with a trace amount of DEHP as the end product showed no significant effect on the germination rate of Brassica chinensis L. seeds (88%) compared to that without DEHP (94%), indicating that the compost can be reused as fertilizer in agricultural applications. These results provide an improved understanding of the DEHP biodegradation via food waste composting without bioaugmentation and hence facilitating its green remediation and conversion into value-added products. Nevertheless, further studies are needed on DEHP biodegradation in large-scale food waste composting or industrial applications.

Microfibers in laundry wastewater: Problem and solution

Data corroborated in this study highlights laundry wastewater as a primary source of microfibers (MFs) in the aquatic environment. MFs can negatively impact the aquatic ecosystem via five possible pathways, namely, acting as carriers of other contaminats, physical damage to digestive systems of aquatic organisms, blocking the digestive tract, releasing toxic chemicals, and harbouring invasive and noxious plankton and bacteria. This review shows that small devices to capture MFs during household laundry activities are simple to use and affordable at household level in developed countries. However, these low cost and small devices are unrealiable and can only achieve up to 40 % MF removal efficiency. In line filtration devices can achieve higher removal efficiency under well maintained condition but their performance is still limited compared to over 98 % MF removal by large scale centralized wastewater treatment. These results infer that effort to increase sanitation coverage to ensure adequate wastewater treatment prior to environmental discharge is likely to be more cost effective than those small devices for capturing MFs. This review also shows that natural fabrics would entail significantly less environmental consequences than synthetic materials. Contribution from the fashion industry to increase the share of natural frabics in the current textile market can also reduce the loading of plastic MFs in the environment.

Two-stage anaerobic membrane bioreactor for co-treatment of food waste and kitchen wastewater for biogas production and nutrients recovery

Co-digestion of organic waste and wastewater is receiving increased attention as a plausible waste management approach toward energy recovery. However, traditional anaerobic processes for co-digestion are particularly susceptible to severe organic loading rates (OLRs) under long-term treatment. To enhance technological feasibility, this work presented a two-stage Anaerobic Membrane Bioreactor (2 S-AnMBR) composed of a hydrolysis reactor (HR) followed by an anaerobic membrane bioreactor (AnMBR) for long-term co-digestion of food waste and kitchen wastewater. The OLRs were expanded from 4.5, 5.6, and 6.9 kg COD m^-3 d^-1 to optimize biogas yield, nitrogen recovery, and membrane fouling at ambient temperatures of 25-32 °C. Results showed that specific methane production of UASB was 249 ± 7 L CH₄ kg^-1 COD_removed at the OLR of 6.9 kg TCOD m^-3 d^-1. Total Chemical Oxygen Demand (TCOD) loss by hydrolysis was 21.6% of the input TCOD load at the hydraulic retention time (HRT) of 2 days. However, low total volatile fatty acid concentrations were found in the AnMBR, indicating that a sufficiently high hydrolysis efficiency could be accomplished with a short HRT. Furthermore, using AnMBR structure consisting of an Upflow Anaerobic Sludge Blanket Reactor (UASB) followed by a side-stream ultrafiltration membrane alleviated cake membrane fouling. The wasted digestate from the AnMBR comprised 42-47% Total Kjeldahl Nitrogen (TKN) and 57-68% total phosphorous loading, making it suitable for use in soil amendments or fertilizers. Finally, the predominance of fine particles (D10 = 0.8 μm) in the ultrafiltration membrane housing (UFMH) could lead to a faster increase in trans-membrane pressure during the filtration process.

An overview of deploying membrane bioreactors in saline wastewater treatment from perspectives of microbial and treatment performance

The discharged saline wastewater has severely influenced the aquatic environment as the treatment performance of many wastewater treatment techniques is limited. In addition, the sources of saline wastewater are also plentiful from agricultural and various industrial fields such as food processing, tannery, pharmaceutical, etc. Although high salinity levels negatively impact the performance of both physicochemical and biological processes, membrane bioreactor (MBR) processes are considered as a potential technology to treat saline wastewater under different salinity levels depending on the adaption of the microbial community. Therefore, this study aims to systematically review the application of MBR widely used in the saline wastewater treatment from the perspectives of microbial structure and treatment efficiencies. At last, the concept of carbon dioxide capture and storage will be proposed for the MBR-treating saline wastewater technologies and considered toward the circular economy with the target of zero emission.

Rapid fabrication of MgO@g-C3N4 heterojunctions for photocatalytic nitric oxide removal

Nitric oxide (NO) is an air pollutant impacting the environment, human health, and other biotas. Among the technologies to treat NO pollution, photocatalytic oxidation under visible light is considered an effective means. This study describes photocatalytic oxidation to degrade NO under visible light with the support of a photocatalyst. MgO@g-C₃N₄ heterojunction photocatalysts were synthesized by one-step pyrolysis of MgO and urea at 550 °C for two hours. The photocatalytic NO removal efficiency of the MgO@g-C₃N₄ heterojunctions was significantly improved and reached a maximum value of 75.4% under visible light irradiation. Differential reflectance spectroscopy (DRS) was used to determine the optical properties and bandgap energies of the material. The bandgap of the material decreases with increasing amounts of MgO. The photoluminescence spectra indicate that the recombination of electron-hole pairs is hindered by doping MgO onto g-C₃N₄. Also, NO conversion, DeNOx index, apparent quantum efficiency, trapping tests, and electron spin resonance measurements were carried out to understand the photocatalytic mechanism of the materials. The high reusability of the MgO@g-C₃N₄ heterojunction was shown by a five-cycle recycling test. This study provides a simple way to synthesize photocatalytic heterojunction materials with high reusability and the potential of heterojunction photocatalysts in the field of environmental remediation.

Assessment of water, sanitation, and hygiene services in district health care facilities in rural area of Mekong Delta, Vietnam

Access to sufficient water, sanitation, and hygiene (WASH) services is a crucial requirement for patients during therapy and general well-being in the hospital. However, in low- and middle-income countries, these services are often inadequate, resulting in increased morbidity and mortality of patients. This study aimed at assessing the current situation of WASH services in six District Health Care Facilities (DHCFs) in rural areas of the Mekong Delta provinces, Vietnam. The results showed that these services were available with inappropriate quality, which did not compromise the stakeholders' needs. The revealed WASH infrastructures have raised concerns about the prolonged hospital stays for patients and push nosocomial infections to a high level. The safety of the water supply was doubted as the high E. coli (> 60%) and total coliform incidence (86%) was observed with very low residual chlorine concentration (< 0.1 mg/L) in water quality assessment. Moreover, water supply contained a high concentration of iron (up to 15.55 mg/L) in groundwater in one DHCF. Technical assessment tool analysis proved that the improper management and lack of knowledge by human resources were the primary roots of the observed status WASH services. Improvement of the perceptions of WASH should be done for the hospital staff with collaboration and support from the government to prevent incidents in the future.

Magnetic biochar derived from macroalgal Sargassum hemiphyllum for highly efficient adsorption of Cu(II): Influencing factors and reusability

In this study, the brown algae Sargassum Hemiphyllum was used as a carbon source for synthesis of magnetic porous biochar via pyrolyzing at high temperature and and doping iron oxide particles (Fe-BAB). Cu (II) species were removed from aqueous solutions using Fe-BAB under various conditions. Fe-BAB demonstrated superior Cu (II) adsorption (105.3 mg g-1) compared to other biochars. On the surface of Fe-BAB, there are several oxygen-containing functional groups, such as -COOH and -OH, which are likely responsible for the excellent heavy metal removal performance. By utilizing magnet, the Fe-BAB can be conveniently separated from the solution and ready for further usage. Multi-adsorption mechanisms were responsible for Cu adsorption on Fe-BAB. Using the magnetic algal biochar for heavy metal removal is feasible due to its high adsorption efficiency and simplicity of separation.

New Insights in factors affecting ground water quality with focus on health risk assessment and remediation techniques

Groundwater is considered as the primary source of water for the majority of the world's population. The preponderance of the nation's drinking water, as well as agricultural and industrial water, comes from groundwater. Groundwater level is becoming increasingly challenging to replenish due to climate change. Fertilizer application and improper processing of industrial waste are the two major anthropogenic drivers of groundwater pollution. Arsenic and cadmium are two of the principal heavy metal pollutants that have affected groundwater quality by human activity. When people are exposed to both non-carcinogenic and carcinogenic contaminants for an extended period, toxic effects might occur. It can have detrimental health effects from long-term exposure to contaminants, even in low amounts. As a result, metal contamination concentrations and fractions can be used to determine potential health concerns. At the same time, contaminants also need to be removed or converted to harmless products by groundwater remediation. Remediation of groundwater quality can be accomplished in several ways, including natural and artificial means. The purpose of this review is to explore a wide range of factors that affect groundwater quality, including their possible health effects. This communication provides state-of-the-art information about remediation approaches for groundwater contamination including hindrances and perspectives in this area of research. The in-depth information provided in different sections of this communication would expand the scope of interdisciplinary research.

Influence of C/N ratios on treatment performance and biomass production during co-culture of microalgae and activated sludge

Novel phycosphere associated bacteria processes are being regarded as a potential and cost-effective strategy for controlling anthropogenic contaminants in wastewater treatment. However, the underlying concern with the process is its vulnerability to improper organic or nutrient intake. This study established a synergistic interaction between microalgae and activated sludge in a three-photobioreactor system (without external aeration) to understand how pollutants could be mitigated whilst simultaneously yielding biomass under different C/N ratios of 1:1, 5:1 and 10:1. The result showed that the superior biomass productivity was facilitated at a C/N ratio of 5:1 (106 mg L^-1 d^-1), and the high degradation rate constants (k_COD = 0.25 d^-1, k_TN = 0.29 d^-1, k_TP = 0.35 d^-1) was approximated using a first-order kinetic model. The removal of pollutants was remarkably high, exceeding 90% (COD), 93% (TN), and 96% (TP). Nevertheless, the C/N ratio of 1:1 resulted in a threefold drop in biomass-specific growth rate (μ = 0.07 d^-1). Microalgal assimilation, followed by bacterial denitrification, is the major pathway of removing total nitrogen when the C/N ratio exceeds 5:1. Activated sludge plays an important role in improving microalgae tolerance to high concentration of ammonia nitrogen and boosting nitrification (light phase) and denitrification (dark phase). The use of phycosphere associated bacteria could be a promising strategy for controlling nutrients pollution and other environmental considerations in wastewater.

Sustainable strategies for combating hydrocarbon pollution: Special emphasis on mobil oil bioremediation

The global rise in industrialization and vehicularization has led to the increasing trend in the use of different crude oil types. Among these mobil oil has major application in automobiles and different machines. The combustion of mobil oil renders a non-usable form that ultimately enters the environment thereby causing problems to environmental health. The aliphatic and aromatic hydrocarbon fraction of mobil oil has serious human and environmental health hazards. These components upon interaction with soil affect its fertility and microbial diversity. The recent advancement in the omics approach viz. metagenomics, metatranscriptomics and metaproteomics has led to increased efficiency for the use of microbial based remediation strategy. Additionally, the use of biosurfactants further aids in increasing the bioavailability and thus biodegradation of crude oil constituents. The combination of more than one approach could serve as an effective tool for efficient reduction of oil contamination from diverse ecosystems. To the best of our knowledge only a few publications on mobil oil have been published in the last decade. This systematic review could be extremely useful in designing a micro-bioremediation strategy for aquatic and terrestrial ecosystems contaminated with mobil oil or petroleum hydrocarbons that is both efficient and feasible. The state-of-art information and future research directions have been discussed to address the issue efficiently.

Comparison of degradation kinetics of tannery wastewater treatment using a nonlinear model by salt-tolerant Nitrosomonas sp. and Nitrobacter sp

Conventional biological treatment has been reported to be ineffective for pollutant removal in tannery wastewater due to high salinity. To overcome it, this work used salt-tolerant bacteria (STB) isolated from a membrane bioreactor to evaluate the organic and nutrient removal through a series of batch experiments. Compared with the control, the STB reactor enhanced the reduction of persistent organics by 11% based on the double exponential decay model. Besides, the removal of NH₄⁺-N is 26% higher, satisfying the first-order decay model. The nitrification was inhibited entirely in control during 48 h, whilst the assimilation process involved 55% of total nitrogen removal. In the STB reactor, nitrification occurred after 12 h, resulting in significantly increased NO₂^--N and NO₃^--N concentrations according to the logistic function. Although nitrification was successfully activated, C/N ratios and free ammonia were identified as limiting factors for STB activity, requiring mitigation strategies in further studies.

Microbial electrolysis: a promising approach for treatment and resource recovery from industrial wastewater

Wastewater is one of the most common by-products of almost every industrial process. Treatment of wastewater alone, before disposal, necessitates an excess of energy. Environmental concerns over the use of fossil fuels as a source of energy have prompted a surge in demand for alternative energy sources and the development of sophisticated procedures to extract energy from unconventional sources. Treatment of municipal and industrial wastewater alone accounts for about 3% of global electricity use while the amount of energy embedded in the waste is at least 2–4 times greater than the energy required to treat the same effluent. The microbial electrolysis cell (MEC) is one of the most efficient technologies for waste-to-product conversion that uses electrochemically active bacteria to convert organic matter into hydrogen or a variety of by-products without polluting the environment. This paper highlights existing obstacles and future potential in the integration of Microbial Electrolysis Cell with other processes like anaerobic digestion coupled system, anaerobic membrane bioreactor and thermoelectric micro converter.

Current application of algae derivatives for bioplastic production: A review

Improper use of conventional plastics poses challenges for sustainable energy and environmental protection. Algal derivatives have been considered as a potential renewable biomass source for bioplastic production. Algae derivatives include a multitude of valuable substances, especially starch from microalgae, short-chain length polyhydroxyalkanoates (PHAs) from cyanobacteria, polysaccharides from marine and freshwater macroalgae. The algae derivatives have the potential to be used as key ingredients for bioplastic production, such as starch and PHAs or only as an additive such as sulfated polysaccharides. The presence of distinctive functional groups in algae, such as carboxyl, hydroxyl, and sulfate, can be manipulated or tailored to provide desirable bioplastic quality, especially for food, pharmaceutical, and medical packaging. Standardizing strains, growing conditions, harvesting and extracting algae in an environmentally friendly manner would be a promising strategy for pollution control and bioplastic production.

Adsorption of norfloxacin from aqueous solution on biochar derived from spent coffee ground: Master variables and response surface method optimized adsorption process

In this study, biochar derived from spent coffee grounds (SCGB) was used to adsorb norfloxacin (NOR) in water. The biochar properties were interpreted by analysis of the specific surface area, morphology, structure, thermal stability, and functional groups. The impacts of pH, NOR, and ion's present on SCGB performance were examined. The NOR adsorption mode of SCGB is best suited to the Langmuir model (R² = 0.974) with maximum absorption capacity (69.8 mg g^-1). By using a Response Surface Method (RSM), optimal adsorption was also found at pH of 6.26, NOR of 24.69 mg L^-1, and SCGB of 1.32 g L^-1. Compared with biochars derived from agriculture such as corn stalks, willow branches, potato stem, reed stalks, cauliflower roots, wheat straw, the NOR adsorption capacity of SCGB was 2-30 times higher, but less than 3-4 times for biochars made from Salix mongolica, luffa sponge and polydopamine microspheres. These findings reveal that spent coffee grounds biochar could effectively remove NOR from aqueous solutions. Approaching biochar derived from coffee grounds would be a promising eco-friendly solution because it utilizes solid waste, saves costs, and creates adsorbents to deal with emerging pollutants like antibiotics.

Composting and its application in bioremediation of organic contaminants

This review investigates the findings of the most up-to-date literature on bioremediation via composting technology. Studies on bioremediation via composting began during the 1990s and have exponentially increased over the years. A total of 655 articles have been published since then, with 40% published in the last six years. The robustness, low cost, and easy operation of composting technology make it an attractive bioremediation strategy for organic contaminants prevalent in soils and sediment. Successful pilot-and large-scale bioremediation of organic contaminants, e.g., total petroleum hydrocarbons, plasticizers, and persistent organic pollutants (POPs) by composting, has been documented in the literature. For example, composting could remediate >90% diesel with concentrations as high as 26,315 mg kg^−a of initial composting material after 24 days. Composting has unique advantages over traditional single- and multi-strain bioaugmentation approaches, including a diverse microbial community, ease of operation, and the ability to handle higher concentrations. Bioremediation via composting depends on the diverse microbial community; thus, key parameters, including nutrients (C/N ratio = 25–30), moisture (55–65%), and oxygen content (O₂ > 10%) should be optimized for successful bioremediation. This review will provide bioremediation and composting researchers with the most recent finding in the field and stimulate new research ideas.

Non-submerged attached growth process for domestic wastewater treatment: Influence of media types and internal recirculation ratios

This study is aimed to comprehend the treatment of non-submerged attached growth systems using bio-sponge, bio-cord, and bio-cloth media. Three reactors were set up with internal recirculation ratio of 1 (IR = 1) and similar media surface area. Bio-sponge and bio-cloth reactors showed removal of COD (79 vs. 76%) and NH₄⁺-N (78 vs. 73%). While bio-cord treatment was deteriorated due to time-dependent process. Multiple linear regression revealed that alkalinity governed the formation degree of the anaerobic zone in bio-sponges, partially affecting nitrification. Increasing IR from 1 to 3 caused sloughing of the attached biomass and was positively correlated with effluent nitrite nitrogen concentration, indicating the sensitivity of nitrification to spatial distribution effects. In addition, bio-sponge system obtained superior performance at IR of 2 while bio-cloth one might be also an effective media for wastewater treatment if having good durability.

Visible light photodegradation of 2,4-dichlorophenol using nanostructured NaBiS2: Kinetics, cytotoxicity, antimicrobial and electrochemical studies of the photocatalyst

Removal of the hazardous and endocrine-disrupting 2,4-dichlorophenol (2,4-DCP) from water bodies is crucial to maintain the sanctity of the ecosystem. As a low bandgap material (1.37 eV), NaBiS₂ was hydrothermally prepared and used as a potential photocatalyst to degrade 2,4-DCP under visible light irradiation. NaBiS₂ appeared to be highly stable and remained structurally undeterred despite thermal variations. With a surface area of 6.69 m²/g, NaBiS₂ has enough surface-active sites to adsorb the reactive molecules and exhibit a significant photocatalytic activity. In alkaline pH, the adsorption of 2,4-DCP on NaBiS₂ appeared to decrease whereas, the acidic and neutral environments favoured the degradation. An increase in the photocatalyst dosage enhanced the degradation efficiency from 81 to 86 %, because of higher vacant adsorbent sites and the electrostatic attraction between NaBiS₂ and 2,4-DCP. The dominant scavengers degraded 2,4-DCP by forming a coordination bond between chlorine's lone pair of electrons and the vacant orbitals of bismuth, following the order hole> OH > singlet oxygen. Being non-toxic to both natural and aquatic systems, NaBiS₂ exhibits antifungal properties at higher concentrations. Finally, the electron-rich NaBiS₂ is an excellent electrocatalyst that effectively degrades organic pollutants and is a promising material for industrial and environmental applications.

Phthalates in the environment: characteristics, fate and transport, and advanced wastewater treatment technologies

Phthalates are well-known emerging contaminants that harm human health and the environment. Therefore, this review aims to discuss about the occurrence, fate, and phthalates concentration in the various environmental matrices (e.g., aquatic, sediment, soil, and sewage sludge). Hence, it is necessary to treat sources containing phthalates before discharging them to aqueous environment. Various advanced wastewater treatments including adsorption process (e.g., biochar, activated carbon), advanced oxidation processes (e.g., photo-fenton, ozonation, photocatalysis), and biological treatment (membrane bioreactor) have been successfully to address this issue with high removal efficiencies (70-95%). Also, the degradation mechanism was discussed to provide a comprehensive understanding of the phthalate removal for the reader. Additionally, key factors that influenced the phthalates removal efficiency of these technologies were identified and summarized with a view towards pilot-scale and industrial applications.

Co-culture of microalgae-activated sludge in sequencing batch photobioreactor systems: Effects of natural and artificial lighting on wastewater treatment

Co-culture using microalgae-activated sludge in Sequencing Batch Photobioreactors (PBRs) was investigated for wastewater treatment performance. This study evaluated the effect of natural and artificial lighting conditons on treatment performance under consideration of energy consumption. The results found that the removal of nutrients and COD of natural lighting condition was only 10% and 13% lower than those of artificial lighting respectively. Generally, artificial lighting mode took an advantage in pollutants removal. However, standing at 0.294 kWh L^-1, the total energy consumption of natural lighting was over two times less than that of artificial lighting. It reveals the natural lighting system played a dominant role for cutting energy costs significantly compared to artificial lighting one (∼57%). As a practical viewpoint on energy aspect and treatment performance, a natural lighting PBR system would be a sustainable option for microalgae-activated sludge co-culture system treating wastewater.

Status of water use and potential of rainwater harvesting for replacing centralized supply system in remote mountainous areas: a case study

The failure of the centralized water supply system forced XY community to become more dependent on uncertain and unstable water sources. The results of surveying 50 households showed that 89.18% of total households depended on water collected from rivers, which contributed 58.3% of the total water volume used for the domestic demands. The average water volume consumed was 19.5 liters/person/day (l/p/d), and 86.5% of households used more than one source; 13.5% of households collected water only from rivers, and 45.94% of families had rainwater harvesting (RWH) for their activities (domestic water demand); however, RWH only provided 9.9% of total water consumption. In this study, basic methods were applied to calculate the storage tanks necessary to balance the water deficit created by drought months. Three levels of water demand (14, 20, and 30 l/p/d) can be the best choices for RWH; for a higher demand (40 and 60 l/p/d), small roof area (30-40 m²), and many people (six to seven) per family, RWH might be impractical because of unsuitable rainfall or excessively large storage tanks.

Arsenic-contaminated groundwater and its potential health risk: A case study in Long An and Tien Giang provinces of the Mekong Delta, Vietnam

The occurrence of arsenic (As) in groundwater (drilled well water) that were used for drinking, cooking, and personal hygiene and its risks to human health in Long An and Tien Giang provinces (Mekong delta, Vietnam) were evaluated in this study. The average As concentrations were 15.92 ± 11.4 μg/L (n = 24, Long An) and 4.95 ± 4.7 μg/L (n = 24, Tien Giang). The average concentrations of As in Long An had not reached the WHO and QCVN 01: 2009/BYT healthy drinking water standard (10 μg/L). When used as a source of water for drinking and daily activities, arsenic-contaminated groundwater may have a direct impact on human health. The risk assessment from groundwater established by the US Environmental Protection Agency (USEPA) was conducted. The risk assessment showed that the average cancer risk (CR) values were 8.68 × 10^-4 (adults) and 2.39 × 10^-3 (children) for Long An, and 2.70 × 10^-4 (adults) and 7.43 × 10^-4 (children) for Tien Giang. These results were significantly higher than the CR (1 × 10^-4) proposed by the USEPA. The adverse health effect was therefore specifically warned by the use of arsenic-contaminated groundwater. This research offers valuable knowledge for efficient water management approaches to guarantee local communities' health protection.

A review on integrated approaches for municipal solid waste for environmental and economical relevance: Monitoring tools, technologies, and strategic innovations

Rapid population growth, combined with increased industrialization, has exacerbated the issue of solid waste management. Poor management of municipal solid waste (MSW) not only has detrimental environmental consequences but also puts public health at risk and introduces several other socioeconomic problems. Many developing countries are grappling with the problem of safe disposing of large amounts of produced municipal solid waste. Unmanaged municipal solid waste pollutes the environment, so its use as a potential renewable energy source would aid in meeting both increased energy needs and waste management. This review investigates emerging strategies and monitoring tools for municipal solid waste management. Waste monitoring using high-end technologies and energy recovery from MSW has been discussed. It comprehensively covers environmental and economic relevance of waste management technologies based on innovations achieved through the integration of approaches.

Pesticide production wastewater treatment by Electro-Fenton using Taguchi experimental design

In this study, the electro-Fenton (EF) method was applied to remove total organic carbon (TOC) from the pesticide production wastewater containing tricyclazole (TC). Statistical Taguchi method was used to optimize the treatment performance. Analysis of variance (ANOVA) indicated that the polynomial regression model fitted experimental data with R² of 0.969. The optimal conditions for eliminating 75.4% TOC and 93.7% TC were 0.2 mM of Fe²⁺, 990 mg/L of Na₂SO₄, 180 min of reaction time at pH 3 with 2.22 mA/cm² of current density. The removal of TC present in the wastewater followed the first-order reaction kinetic model (R² = 0.993); while that was the second-order kinetic model in the case of the TOC removal (R² = 0.903). In addition, the experimental results and theory approaches (density functional theory and natural bond orbital calculations) also showed the C-N bond breaking and nitrate ions cleavage to ammonia. Acute toxicity of the pesticide wastewater after treatment (PWAT) on microcrustaceans showed that the treated wastewater still exhibited high toxicity against D. magna, with LC₅₀ values of 3.84%, 2.68%, 2.05%, and 1.78% at 24 h, 48 h, 72 h, and 96 h, respectively.

Submerged membrane filtration process coupled with powdered activated carbon for nonylphenol ethoxylates removal

A combination of a submerged membrane filtration system and powdered activated carbon (PAC) was investigated for nonylphenol ethoxylates removal. Both filtration flux and initial powdered activated carbon dosage had significant effects on the micropollutants removal efficiency. The best performance was achieved under the filtration flux of 20 L/m².h and the initial powdered activated carbon of 50 mg/L. The removal efficiencies of nonylphenol ethoxylates was obtained at 75±5% in the first 60 hours, and then decreased at 55±7% and 23±11% in the following hours, respectively. As observed, over 65% of dissolved organic carbon mass adsorbed into powdered activated carbon that was suspended in the bulk phase, and the remainder was adsorbed into powdered activated carbon that deposited on the membrane surface. It reveals that the combination between submerged membrane filtration and PAC could be an effective solution for enhancing removal of micropollutants from water.

Human health risk simulation and assessment of heavy metal contamination in a river affected by industrial activities

The human health risks caused by heavy metal contamination (As, Cd, Cr, Cu, Hg, Pb, Ni, and Zn) in the surface water of the Houjing River, the most contaminated river in southern Taiwan, were assessed in this study. Firstly, heavy metal contamination was evaluated by the contamination factors (CF) and the metal indexes (MI). Secondly, the human health risks due to heavy metal contamination were simulated using the Adaptive Risk Assessments Modeling System (ARAMS) through three scenarios; fish ingestion, dermal water contact, and incidental water ingestion during swimming. The hazard quotient (HQ) and the hazard index (HI) were used to evaluate non-carcinogenic risks, while carcinogenic risks were estimated by the lifetime cancer incidence risk index (CR) and the cumulative cancer risk (CCR). The results showed that the synergistic contamination of heavy metals in the surface water was severe (MI = 12.4), with the highest contribution from Cu, Ni, and Pb. Copper had the highest non-carcinogenic risk at the "adverse effect" level, while Ni and Cr had the highest carcinogenic risk at an "unacceptable" level. In addition, the cumulative risks of fish ingestion (HI_FI = 6.75 and CCR_FI = 1.25E-03) were significantly higher than those of the swimming scenarios (HI_(DC + WI) = 1.94E-03 and CCR_(DC + WI) = 9.32E-08). The results from this study will be beneficial for immediate and future contamination control measures and human health management plans for this study area. This study has also demonstrated the effectiveness of using ARAMS in human health risk assessment.

Contamination, source attribution, and potential health risks of heavy metals in street dust of a metropolitan area in Southern Vietnam

This study investigates distribution, pollution indices, and potential risk assessment for human health and ecology of eight heavy metals in twenty-five street dust samples collected from metropolitan area-Ho Chi Minh City, Vietnam. Results showed that Zn was of the highest concentration (466.4 ± 236.5 mg/kg), followed by Mn (393.9 ± 93.2 mg/kg), Cu (153.7 ± 64.7 mg/kg), Cr (102.4 ± 50.5 mg/kg), Pb (49.6 ± 21.4 mg/kg), Ni (36.2 ± 15.4 mg/kg), Co (7.9 ± 1.9 mg/kg), and Cd (0.5 ± 0.5 mg/kg). The principal component analysis revealed that three sources of heavy metals measured in street dust include vehicular activities (32.38%), mixed source of vehicular and residential activities (26.72%), and mixture of industrial and natural sources (20.23%). The geo-accumulation index values showed levels of non-pollution to moderately pollution for Mn and Co; moderately pollution for Ni; moderately to strongly pollution for Cd, Cr, and Pb; and strongly pollution for Cu and Zn. The potential ecological risk values of all sampling sites were close to the high-risk category. Zn (28.9%), Cu (25.4%), and Mn (24.4%) dominantly contributed to the ecological risk. For non-carcinogenic risk, the hazard quotient values for both children and adults were within a safety level. For carcinogenic risk, the TCR_Children was about 3 times higher than TCR_Adults, but still within a tolerable limit (1 × 10^-6 to 1 × 10^-4) of cancer risk. Cr was a major contribution to potential risks in humans. Such studies on heavy metal in street dust are crucial but are still limited in Vietnam/or metropolitan area in Southeast Asia. Therefore, this study can fill the information gap about heavy metal contaminated street dust in a metropolitan area of Vietnam.

A critical review on various feedstocks as sustainable substrates for biosurfactants production: a way towards cleaner production

The quest for a chemical surfactant substitute has been fuelled by increased environmental awareness. The benefits that biosurfactants present like biodegradability, and biocompatibility over their chemical and synthetic counterparts has contributed immensely to their popularity and use in various industries such as petrochemicals, mining, metallurgy, agrochemicals, fertilizers, beverages, cosmetics, etc. With the growing demand for biosurfactants, researchers are looking for low-cost waste materials to use them as substrates, which will lower the manufacturing costs while providing waste management services as an add-on benefit. The use of low-cost substrates will significantly reduce the cost of producing biosurfactants. This paper discusses the use of various feedstocks in the production of biosurfactants, which not only reduces the cost of waste treatment but also provides an opportunity to profit from the sale of the biosurfactant. Furthermore, it includes state-of-the-art information about employing municipal solid waste as a sustainable feedstock for biosurfactant production, which has not been simultaneously covered in many published literatures on biosurfactant production from different feedstocks. It also addresses the myriad of other issues associated with the processing of biosurfactants, as well as the methods used to address these issues and perspectives, which will move society towards cleaner production.