Electrochemical filtration for drinking water purification: A review on membrane materials, mechanisms and roles

Electrochemical filtration can not only enrich low concentrations of pollutants but also produce reactive oxygen species to interact with toxic pollutants with the assistance of a power supply, making it an effective strategy for drinking water purification. In addition, the application of electrochemical filtration facilitates the reduction of pretreatment procedures and the use of chemicals, which has outstanding potential for maximizing process simplicity and reducing operating costs, enabling the production of safe drinking water in smaller installations. In recent years, the research on electrochemical filtration has gradually increased, but there has been a lack of attention on its application in the removal of low concentrations of pollutants from low conductivity water. In this review, membrane substrates and electrocatalysts used to improve the performance of electrochemical membranes are briefly summarized. Meanwhile, the application prospects of emerging single-atom catalysts in electrochemical filtration are also presented. Thereafter, several electrochemical advanced oxidation processes coupled with membrane filtration are described, and the related working mechanisms and their advantages and shortcomings used in drinking water purification are illustrated. Finally, the roles of electrochemical filtration in drinking water purification are presented, and the main problems and future perspectives of electrochemical filtration in the removal of low concentration pollutants are discussed.

Comparative study of molecularly imprinted polymer surface modified magnetic silica aerogel, zeolite Y, and MIL-101(Cr) for dispersive solid phase extraction of fuel ether oxygenates in drinking water

The study was performed in two phases. First, the polymerization was carried out upon three magnetized surfaces of silica aerogel, zeolite Y, and MIL-101(Cr). Then, optimal molecularly imprinted polymer and optimal extraction conditions were determined by the central composite design-response surface method. Subsequently, the validation parameters of dispersive solid-phase extraction based optimal molecularly imprinted polymer were examined for the extraction of the fuel ether oxygenates. The optimal conditions include the type of adsorbent: Zeolite-magnetic molecularly imprinted polymer, the amount of adsorbent: 40 mg, pH: 7.7, and absorption time: 24.8 min which was selected with desirability equal to 0.996. The calibration graphs were linear between 1 and 100 μg L-1, with good correlation coefficients. The limits of detection were found to be 0.64, 0. 4, and 0.34 μg L-1 for methyl tert-butyl ether, ethyl tert-butyl ether, and tert butyl formate, respectively. The method proved reliable for analyzing fuel ether oxygenates in drinking water.

The concentration of phthalates in drinking water in Iran: A systematic review and meta-analysis

PAE and PC polymers, such as BPA, are utilized to make water bottles. Due to the lack of polymer-chemical interaction, PAE can enter drinking bottles during production, wrapping, and keeping. Phthalates can transfer from the bottle to the water depending on keeping conditions (temperature, time, sunlight intensity), pH, and bottle capacity. Since there haven't been previous studies published on the subject, the aim of this meta-analysis and systematic review research is to determine the level of phthalates in drinking water consumed in Iranian cities. Web of Science, Science of Direct, Scopus, and PubMed, databases have been used in this study. Eight studies were selected from 556 initial publications after screening for duplication and irrelevant information. Articles from January 1, 2000, to February 10, 2024, were found in the mentioned databases. Among the types of phthalates, the concentration of DEHP was reported higher than the others Because its concentration has been reported in seven out of eight studies. The highest concentration of DEHP was reported by Mehraie(2.22 µg/l), Zare Jeddi (0.8 µg/l), Yousefi (0.77 µg/l), Abtahi (0.76 µg/l), Zare Jeddi (0.42 µg/l), Abdolahnejad(0.15 µg/l), and Pourzamani (0.08 µg/l). The highest concentration of DEP, DBP, BBP, and PA was reported by Abtahi (0.77 µg/l) and Esteki (2.25 µg/l), Mehraie(0.93 µg/l), and Pourzamani (0.83 µg/l). The results of this study showed that the most important phthalates measured in drinking water include DEP, DEHP, DBP, BBP, and PA. According to the results of the present studies, the most important factor in the increase of phthalates is the storage conditions of drinking water (temperature, sunlight, and the type of pipe or bottle).

A comprehensive dataset for the evaluation of a horizontal tubular flocculator implemented for drinking water treatment

This article presents a set of data obtained during the evaluation of a horizontal flow tubular flocculator for the provision of drinking water in developing communities. The HFTF is presented as an alternative technology to replace conventional flocculators, allowing high efficiency in the subsequent sedimentation and filtration processes. For obtaining the data, experimental tests were carried out using lengths of 68.4 m and 97.6 m for the HFTF, these lengths were combined with flow rates of 0.25, 0.5, 0.75, 1.0 and 2.0 L/s, as well as raw water turbidities of 10, 20, 50, 100 and 200 NTU. The data set generated from measurements and observations made during experimental field tests is detailed. The resulting data set covers the main parameters that determine the quality of drinking water, such as turbidity and colour, as well as flocculation efficiency data. The data from the experimental system were compared with a conventional treatment plant that has a baffle flocculator. Likewise, data on the retention time and velocity gradient are presented that allowed the hydraulic characteristics of the HFTF are evaluated. This data set has significant potential for reuse in future research and development related to water treatment technologies in developing community settings. Detailed data has been collected on various operating conditions of the HFTF, such as different lengths, water flow rates and turbidity levels, as well as measurements of key parameters such as turbidity, colour, flocculation efficiency, retention time and velocity gradient, these Data could be used in future research and development related to water treatment technologies. Furthermore, a comparison of data from the experimental system with a conventional treatment plant provides useful insight into the relative performance of different water treatment technologies, which could be of interest to researchers, system designers and public policymakers in the field of drinking water supply in developing communities.

Crowdsourcing citizens for statewide mapping of per- and polyfluoroalkyl substances (PFAS) in Florida drinking water

Per- and polyfluoroalkyl substances (PFAS) are a class of persistent chemicals that have been associated with a diverse array of adverse environmental and human health related effects. In addition to a growing list of health concerns, PFAS are also ubiquitously used and pervasive in our natural and built environments, and they have an innate ability to be highly mobile once released into the environment with an unmatched ability to resist degradation. As such, PFAS have been detected in a wide variety of environmental matrices, including soil, water, and biota; however, the matrix that largely dictates human exposure to PFAS is drinking water, in large part due to their abundance in water sources and our reliance on drinking water. As Florida is heavily reliant upon water and its varying sources, the primary objective of this study was to survey the presence of PFAS in drinking water collected from taps from the state of Florida (United States). In this study, 448 drinking water samples were collected by networking with trained citizen scientists, with at least one sample collected from each of the 67 counties in Florida. Well water, tap water, and bottled water, all sourced from Florida, were extracted and analyzed (31 PFAS) using isotope dilution and ultra-high-performance liquid chromatography - tandem mass spectrometry (UHPLC-MS/MS). Overall, when examining ∑PFAS: the minimum, maximum, median, and mean were ND, 219, 2.90, and 14.06 ng/L, respectively. The data herein allowed for a comparison of PFAS in drinking water geographically within the state of Florida, providing vital baseline concentrations for prospective monitoring and highlighting hotspots that require additional testing and mitigation. By incorporating citizen scientists into the study, we aimed to educate impacted communities regarding water quality issues and solutions.

Microplastics contamination in water supply system and treatment processes

Due to global demand, millions of tons of plastics have been widely consumed, resulting in the widespread entry of vast amounts of microplastic particles into the environment. The presence of microplastics (MPs) in water supplies, including bottled water, has undergone systematic review, assessing the potential impacts of MPs on humans through exposure assessment. The main challenges associated with current technologies lie in their ability to effectively treat and completely remove MPs from drinking and supply water. While the risks posed by MPs upon entering the human body have not yet been fully revealed, there is a predicted certainty of negative impacts. This review encompasses a range of current technologies, spanning from basic to advanced treatments and varying in scale. However, given the frequent detection of MPs in drinking and bottled water, it becomes imperative to implement comprehensive management strategies to address this issue effectively. Consequently, integrating current technologies with management options such as life-cycle assessment, circular economy principles, and machine learning is crucial to eliminating this pervasive problem.

Acids from fruits generate photoactive Fe-complexes, enhancing solar disinfection of water (SODIS): A systematic study of the novel "fruto-Fenton" process, effective over a wide pH range (4 - 9)

This study aimed to enhance solar disinfection (SODIS) by the photo-Fenton process, operated at natural pH, through the re-utilization of fruit wastes. For this purpose, pure organic acids present in fruits and alimentary wastes were tested and compared with synthetic complexing agents. Owing to solar light, complexes between iron and artificial or natural chelators can be regenerated through ligand-to-metal charge transfer (LMCT) during disinfection. The target complexes were photoactive under solar light, and the Fe:Ligand ratios for ex situ prepared iron complexes were assessed, achieving a balance between iron solubilization and competition with bacteria as a target for oxidizing species. In addition, waste extracts containing natural acidic ligands were an excellent raw material for our disinfection enhancement purposes. Indeed, lemon and orange juice or their peel infusions turned out to be more efficient than commercially available organic acids, leading to complete inactivation in less than 1 h by this novel "fruto-Fenton" process, i.e. in the presence of a fruit-derived ligand, Fe(II) and H2O2. Finally, its application in Lake Leman water and in situ complex generation led to effective bacterial inactivation, even in mildly alkaline surface waters. This work proposes interesting SODIS and fruit-mediated photo-Fenton enhancements for bacterial inactivation in resource-poor contexts and/or under the prism of circular economy.

Elucidation of arsenic detoxification mechanism in Marchantia polymorpha: The role of ACR3

The arsenic-specific ACR3 transporter plays pivotal roles in As detoxification in yeast and a group of ancient tracheophytes, the ferns. Despite putative ACR3 genes being present in the genomes of bryophytes, whether they have the same relevance also in this lineage is currently unknown. In this study, we characterized the MpACR3 gene from the bryophyte Marchantia polymorpha L. through a multiplicity of functional approaches ranging from phylogenetic reconstruction, expression analysis, loss- and gain-of-function as well as genetic complementation with an MpACR3 gene tagged with a fluorescent protein. Genetic complementation demonstrates that MpACR3 plays a pivotal role in As tolerance in M. polymorpha, with loss-of-function Mpacr3 mutants being hypersensitive and MpACR3 overexpressors more tolerant to As. Additionally, MpACR3 activity regulates intracellular As concentration, affects its speciation and controls the levels of intracellular oxidative stress. The MpACR3::3xCitrine appears to localize at the plasma membrane and possibly in other endomembrane systems. Taken together, these results demonstrate the pivotal function of ACR3 detoxification in both sister lineages of land plants, indicating that it was present in the common ancestor to all embryophytes. We propose that Mpacr3 mutants could be used in developing countries as low-cost and low-technology visual bioindicators to detect As pollution in water.

Trihalomethanes in global drinking water: Distributions, risk assessments, and attributable disease burden of bladder cancer

This study aimed to assess the global spatiotemporal variations of trihalomethanes (THMs) in drinking water, evaluate their cancer and non-cancer risks, and THM-attributable bladder cancer burden. THM concentrations in drinking water around fifty years on a global scale were integrated. Health risks were assessed using Monte Carlo simulations and attributable bladder cancer burden was estimated by comparative risk assessment methodology. The results showed that global mean THM concentrations in drinking water significantly decreased from 78.37 μg/L (1973-1983) to 51.99 μg/L (1984-2004) and to 21.90 μg/L (after 2004). The lifestage-integrative cancer risk and hazard index of THMs through all exposure pathways were acceptable with the average level of 6.45 × 10-5 and 7.63 × 10-2, respectively. The global attributable disability adjusted of life years (DALYs) and the age-standardized DALYs rate (ASDR) dropped by 16% and 56% from 1990-1994 to 2015-2019, respectively. A big decline in the attributable ASDR was observed in the United Kingdom (62%) and the United States (27%), while China experienced a nearly 3-fold increase due to the expanded water supply coverage and increased life expectancy. However, China also benefited from the spread of chlorination, which helped reduce nearly 90% of unsafe-water-caused mortality from 1998 to 2018.

eutropha to chloramination for drinking water treatment

Chloramination is an effective strategy for eliminating pathogens from drinking water and repressing their regrowth in water distribution systems. However, the inevitable release of NH4+ potentially promotes nitrification and associated ammonia-oxidizing bacteria (AOB) contamination. In this study, AOB (Nitrosomona eutropha) were isolated from environmental water and treated with two disinfection stages (chloramine disinfection and chloramine residues) to investigate the occurrence mechanisms of AOB in chloramination. The results showed that N. eutropha had considerable resistance to monochloramine compared to Escherichia coli, whose inactivation rate constant was 19.4-fold lower. The higher resistance was attributed to high levels of extracellular polymer substances (EPS) in AOB, which contribute to AOB surviving disinfection and entering the distribution system. In AOB response to the chloramine residues stage, the respiratory activity of N. eutropha remained at a high level after three days of continuous exposure to high chloramine residue concentrations (0.5-1.5 mg/L). Reverse transcription-quantitative polymerase chain reaction (RT-qPCR) suggested that the mechanism of N. eutropha tolerance involved a significantly high expression of the intracellular oxidative stress-regulating (sodB, txrA) and protein-related (NE1545, NE1546) genes. Additionally, this process enhanced EPS secretion and promoted biofilm formation. Adhesion predictions based on the XDLVO theory corroborated the trend of biofilm formation. Overall, the naturally higher resistance contributed to the survival of AOB in primary disinfection; the enhanced antioxidant response of surviving N. eutropha accompanied by biofilm formation was responsible for their increased resistance to the residual chloramines.

Research progress on the generation of NDMA by typical PPCPs in disinfection treatment of water environment in China: A review

The drugs and personal care products in water sources are potential threats to the ecological environment and drinking water quality. In recent years, the presence of PPCPs has been detected in multiple drinking water sources in China. PPCPs are usually stable and resistant to degradation in aquatic environments. During chlorination, chloramination, and ozonation disinfection processes, PPCPs can act as precursor substances to generate N-nitrosodimethylamine (NDMA) which is the most widely detected nitrosamine byproduct in drinking water. This review provides a comprehensive overview of the impact of PPCPs in China's water environment on the generation of NDMA during disinfection processes to better understand the correlation between PPCPs and NDMA generation. Chloramine is the most likely to form NDMA with different disinfection methods, so chloramine disinfection may be the main pathway for NDMA generation. Activated carbon adsorption and UV photolysis are widely used in the removal of NDMA and its precursor PPCPs, and biological treatment is found to be a low-cost and high removal rate method for controlling the generation of NDMA. However, there are still certain regional limitations in the investigation and research on PPCPs, and other nitrosamine by-products such as NMEA, NDEA and NDBA should also be studied to investigate the formation mechanism and removal methods.

Public health assessment of Kenyan ASGM communities using multi-element biomonitoring, dietary and environmental evaluation

The Kakamega gold belt's natural geological enrichment and artisanal and small-scale gold mining (ASGM) have resulted in food and environmental pollution, human exposure, and subsequent risks to health. This study aimed to characterise exposure pathways and risks among ASGM communities. Human hair, nails, urine, water, and staple food crops were collected and analysed from 144 ASGM miners and 25 people from the ASGM associated communities. Exposure to PHEs was predominantly via drinking water from mine shafts, springs and shallow-wells (for As>Pb>Cr>Al), with up to 366 µg L-1 arsenic measured in shaft waters consumed by miners. Additional exposure was via consumption of locally grown crops (for As>Ni>Pb>Cr>Cd>Hg>Al) besides inhalation of Hg vapour and dust, and direct dermal contact with Hg. Urinary elemental concentrations for both ASGM workers and wider ASGM communities were in nearly all cases above bioequivalents and reference upper thresholds for As, Cr, Hg, Ni, Pb and Sb, with median concentrations of 12.3, 0.4, 1.6, 5.1, 0.7 and 0.15 µg L-1, respectively. Urinary As concentrations showed a strong positive correlation (0.958) with As in drinking water. This study highlighted the importance of a multidisciplinary approach in integrating environmental, dietary, and public health investigations to better characterise the hazards and risks associated with ASGM and better understand the trade-offs associated with ASGM activities relating to public health and environmental sustainability. Further research is crucial, and study results have been shared with Public Health and Environmental authorities to inform mitigation efforts.

Private groundwater contamination and risk management: A comparative scoping review of similarities, drivers and challenges across two socio-economically developed regions

Consolidation of multi-domain risk management research is essential for strategies facilitating the concerted government (educational) and population-level (behavioural) actions required to reduce microbial private groundwater contamination. However, few studies to date have synthesised this literature or sought to ascertain the causal generality and extent of supply contamination and preventive responses. In light of the Republic of Ireland (ROI) and Ontario's high reliance and research focus on private wells and consequent utility for empirical comparison, a scoping review of pertinent literature (1990-2022) from both regions was undertaken. The SPICE (Setting, Perspective, Intervention, Comparison, Evaluation) method was employed to inform literature searches, with Scopus and Web of Science selected as primary databases for article identification. The review identified 65 relevant articles (Ontario = 34, ROI = 31), with those investigating well user actions (n = 22) and groundwater quality (n = 28) the most frequent. A markedly higher pooled proportion of private supplies in the ROI exhibited microbial contamination (38.3 % vs. 4.1 %), despite interregional similarities in contamination drivers (e.g., weather, physical supply characteristics). While Ontarian well users demonstrated higher rates of historical (≥ 1) and annual well testing (90.6 % vs. 71.1 %; 39.1 % vs. 8.6 %) and higher rates of historical well treatment (42.3 % vs. 24.3 %), interregional levels of general supply knowledge were analogous (70.7 % vs. 71.0 %). Financial cost, organoleptic properties and residence on property during supply construction emerged as predictors of cognition and behaviour in both regions. Review findings suggest broad interregional similarities in drivers of supply contamination and individual-level risk mitigation, indicating that divergence in contamination rates may be attributable to policy discrepancies - particularly well testing incentivisation. The paucity of identified intervention-oriented studies further highlights the importance of renewed research and policy agendas for improved, targeted well user outreach and incentivised, convenience-based services promoting routine supply maintenance.

Incidence of per- and polyfluoroalkyl substances (PFAS) in private drinking water supplies in Southwest Virginia, USA

Per- and polyfluoroalkyl substances (PFAS) are a class of man-made contaminants of human health concern due to their resistance to degradation, widespread environmental occurrence, bioaccumulation in living organisms, and potential negative health impacts. Private drinking water supplies may be uniquely vulnerable to PFAS contamination in impacted areas, as these systems are not protected under federal regulations and often include limited treatment or remediation, if contaminated, prior to use. The goal of this study was to determine the incidence of PFAS contamination in private drinking water supplies in two counties in Southwest Virginia, USA (Floyd and Roanoke) that share similar bedrock geologies, are representative of different state Department of Health risk categories, and to examine the potential for reliance on citizen-science based strategies for sample collection in subsequent efforts. Samples for inorganic ions, bacteria, and PFAS analysis were collected on separate occasions by participants and experts at the home drinking water point of use (POU) for comparison. Experts also collected outside tap samples for analysis of 30 PFAS compounds. At least one PFAS was detectable in 95 % of POU samples collected (n = 60), with a mean total PFAS concentration of 23.5 ± 30.8 ppt. PFOA and PFOS, two PFAS compounds which presently have EPA health advisories, were detectable in 13 % and 22 % of POU samples, respectively. On average, each POU sample contained >3 PFAS compounds, and one sample contained as many as 8 compounds, indicating that exposure to a mixture of PFAS in drinking water may be occurring. Although there were significant differences in total PFAS concentrations between expert and participant collected samples (Wilcoxon, alpha = 0.05), collector bias was inconsistent, and may be due to the time of day of sampling (i.e. morning, afternoon) or specific attributes of a given home. Further research is required to resolve sources of intra-sample variability.

Assessment of heavy metals level in chicken with indeterminate analysis in localities of Lahore, Pakistan

The poultry industry is a significant source of animal protein, vitamins, and minerals, particularly through the consumption of chicken meat. In order to conduct the study, 100 samples of liver, chicken feed, and drinking water were collected in nearby areas of Lahore. The investigation aims to detect the presence of specific heavy metals in the collected samples. For this purpose, atomic absorption spectroscopy (AAS) was used to detect heavy metals after proper preparation of the samples. The experimentally observed data were analyzed through a novel statistical approach known as neutrosophic statistics. It was observed that copper (Cu), zinc (Zn), and cadmium (Cd) were the most prominent metals detected with contamination above the safe limits (for chicken drinking water (Zn = 23.09±13.67 mg/L, Cu = 3.84±3.04 mg/L, Cd = 0.805±0.645 mg/L, Pb = 0.275±0.095 mg/L, As = 0.982±0.978 mg/L), for chicken feed (Zn = 2.705±0.715 mg/kg, Cu = 1.85±0.53 mg/kg, Cd = 3.065±1.185 mg/kg, Pb = 0.215±0.175 mg/kg, As = 0.68±0.22 mg/kg), and chicken's liver (Zn = 3.93±0.66 mg/kg, Cu = 1.2±0.52 mg/kg, Cd = 0.07±0.05 mg/kg, Pb = 0.805±0.775 mg/kg, As = 1.05±0.8 mg/kg)). Similarly, the statistical analysis leads that the findings emphasize the importance of monitoring and mitigating heavy metal contamination in the poultry industry to ensure the safety and quality of poultry products.

DDT contamination in water resources of some African countries and its impact on water quality and human health

Dichlorodiphenyltrichloroethane (DDT) usage has been prohibited in developed nations since 1972 but is exempted for use in indoor residual spraying (IRS) in developing countries, including African countries, for malaria control. There have been no previous reviews on DDT residues in water resources in Africa. The study aimed to provide a review of available research investigating the levels of DDT residues in water sources in Africa and to assess the consequent human health risks. A scoping review of published studies in Africa was conducted through a systematic electronic search using PubMed, Web of Science, EBSCO HOST, and Scopus. A total of 24 articles were eligible and reviewed. Concentrations of DDT ranged from non-detectable levels to 81.2 μg/L. In 35% of the studies, DDT concentrations surpassed the World Health Organization (WHO) drinking water guideline of 1 μg/L in the sampled water sources. The highest DDT concentrations were found in South Africa (81.2 μg/L) and Egypt (5.62 μg/L). DDT residues were detected throughout the year in African water systems, but levels were found to be higher during the wet season. Moreover, water from taps, rivers, reservoirs, estuaries, wells, and boreholes containing DDT residues was used as drinking water. Seven studies conducted health risk assessments, with two studies identifying cancer risk values surpassing permissible thresholds in water sampled from sources designated for potable use. Non-carcinogenic health risks in the studies fell below a hazard quotient of 1. Consequently, discernible evidence of risks to human health surfaced, given that the concentration of DDT residues surpassed either the WHO drinking water guidelines or the permissible limits for cancer risk in sampled drinking sources within African water systems. Therefore, alternative methods for malaria vector control should be investigated and applied.

Estimation and evaluation of the risks of protozoa infections associated to the water from a treatment plant in southern Brazil using the Quantitative Microbiological Risk Assessment Methodology (QMRA)

In this study, the Quantitative Microbial Risk Assessment (QMRA) methodology was applied to estimate the annual risk of Giardia and Cryptosporidium infection associated with a water treatment plant in southern Brazil. The efficiency of the treatment plant in removing protozoa and the effectiveness of the Brazilian legislation on microbiological protection were evaluated, emphasizing the relevance of implementing the QMRA in this context. Two distinct approaches were employed to estimate the mechanical removal of protozoa: The definitions provided by the United States Environmental Protection Agency (USEPA), and the model proposed by Neminski and Ongerth. Although the raw water collected had a higher concentration of Giardia cysts than Cryptosporidium oocysts, the estimated values for the annual risk of infection were significantly higher for Cryptosporidium than for Giardia. From a general perspective, the risk values of protozoa infection were either below or very near the limit set by the World Health Organization (WHO). In contrast, all the risk values of Cryptosporidium infection exceeded the threshold established by the USEPA. Ultimately, it was concluded that the implementation of the QMRA methodology should be considered by the Brazilian authorities, as the requirements and guidelines provided by the Brazilian legislation proved to be insufficient to guarantee the microbiological safety of drinking water. In this context, the QMRA application can effectively contribute to the prevention and investigation of outbreaks of waterborne disease.

Systematic review and meta-analysis of arsenic concentration in drinking water sources of Iran

Recent studies have found arsenic contamination of drinking water in some parts of Iran, as in many other countries. Thus, a comprehensive systematic review is necessary to assess the distribution and concentration of arsenic in drinking water sources. For this purpose, articles published from the first identification until December 2023, were retrieved from various national and international databases. Of all the studies examined (11,726), 137 articles were selected for review based on their conceptual relationship to this survey. A review of the extracted studies presented that ICP methods (ICP-MS, ICP-OES, 56%) and atomic absorption spectrophotometry (AAS, 34.1%) were the two most commonly used techniques for the analysis of arsenic in water samples. The order of arsenic content in the defined study areas is descending, as follows: northwest ˃ southeast ˃ southwest ˃ northeast. A review of studies performed in Iran depicted that provinces such as Kurdistan, Azerbaijan, and Kerman have the highest arsenic concentrations in water resources. Accordingly, the maximum concentration of arsenic was reported in Rayen, Kerman, and ranged from < 0.5-25,000 µg/L. The primary cause of elevated arsenic levels in water resources appears to be geologic structure, including volcanic activity, biogeochemical processes, sulfur-bearing volcanic rocks, Jurassic shale, the spatial coincidence of arsenic anomalies in tube wells and springs, and, to some extent, mining activities. The findings of the presented survey indicate that it is essential to take serious measures at the national level to minimize the health risks of arsenic contamination from drinking water consumption.

Detection and characterisation of microplastics in tap water from Gauteng, South Africa

This study reports the presence, concentration, and characteristics of microplastics (MPs) in tap water in three suburbs in Gauteng Province in South Africa. Physical characterisation was conducted using stereomicroscopy and scanning electron microscopy following staining of MPs with the Rose Bengal dye. The concentrations of MPs in all samples ranged from 4.7 to 31 particles/L, with a mean of 14 ± 5.6 particles/L. Small-sized (<1 mm) and fibrous-shaped MPs were most abundant in all samples. Fibers accounted for 83.1% of MPs in samples from all the three areas, followed by fragments (12.4%), pellets/beads (3.1%), and films (1.5%), with a minor variation in the distribution of shapes and sizes in samples from each area. Raman microspectroscopy was used for chemical analysis, and five polymers were identified, namely: high-density polyethylene, polyurethane, polyethylene terephthalate, poly(hexamethylene terephtalamide), and poly(acrylamide-co-acrylic acid). C.I Pigment Red 1, C.I. Solvent Yellow 4, Potassium indigotetrasulphonate, and C.I Pigment Black 7 were the colourants detected. These colourants are carcinogenic and mutagenic and are potentially toxic to humans. The prevalence of MPs in tap water implies their inadequate removal during water treatment. For instance, the presence of poly(AM-co-AA) suggests that drinking water treatment plants may be a potential source of MPs in tap water. Other polymers, e.g., high-density polyethylene may be released from pipes during the transportation of drinking water. The estimated daily consumption of MPs from tap water was 1.2, 0.71, and 0.50 particles/kg.day for children, men, and women, respectively. The findings of this study provide evidence of the presence of MPs in drinking water in South Africa, thus giving some insights into the performance of treatment plants in removing these contaminants and a benchmark for the formulation of standard limits for the amount of MPs in drinking water.

Exposure to Nickel-Cadmium Contamination of Drinking Water Culminates in Liver Cirrhosis, Renal Azotemia, and Metabolic Stress in Rats

Drinking water polluted by heavy metals has the potential to expose delicate biological systems to a range of health issues. This study embraced the health risks that may arise from subchronic exposure of thirty-four male Wistar rats to nickel (Ni)-cadmium (Cd)-contaminated water. It was done by using the Box-Behnken design (BBD) with three treatment factors (Ni and Cd doses at 50-150 mg/L and exposure at 14-21-28 days) at a single alpha level, resulting in seventeen experimental combinations. Responses such as serum creatinine (CREA) level, blood urea nitrogen (BUN) level, BUN/CREA ratio (BCR), aspartate and alanine aminotransferases (AST and ALT) activities, and the De Ritis ratio (DRR), as well as malondialdehyde (MDA) level, catalase (CAT), and superoxide dismutase (SOD) activities, were evaluated. The results revealed that these pollutants jointly caused hepatocellular damage by raising AST and ALT activities and renal dysfunction by increasing CREA and BUN levels in Wistar rats' sera (p < 0.05). These outcomes were further supported by BCR and DRR values beyond 1. In rats' hepatocytes and renal tissues, synergistic interactions of these metals resulted in higher MDA levels and significant impairments of CAT and SOD activities (p < 0.05). In order to accurately forecast the effects on the responses, the study generated seven acceptable regression models (p < 0.05) with r-squared values of > 80% at no discernible lack of fit (p > 0.05). The findings hereby demonstrated that Wistar rats exposed to these pollutants at varied doses had increased risks of developing liver cirrhosis and azotemia marked by metabolic stress.

How to achieve adequate quenching for DBP analysis in drinking water?

Quenching is an important step to terminate disinfection during preparation of disinfected water samples for the analysis of disinfection byproducts (DBPs). However, an incomplete quenching might result in continued reactions of residual chlorine, whereas an excessive quenching might decompose target DBPs. Therefore, an adequate quenching to achieve simultaneous disinfection termination and DBP preservation is of particular importance. In this study, the two-stage reaction kinetics of chlorine and three commonly used quenching agents (i.e., ascorbic acid, sodium thiosulfate, and sodium sulfite) were determined. Stopping quenching during the first stage prevented interactions of residual chlorine with natural organic matter. Complete quenching was achieved by minimizing the quenching time for ascorbic acid and sodium sulfite, while limiting the quenching time to less than 3 min for sodium thiosulfate. At the optimized quenching times, the molar ratios (MRs) of quenching agent to chlorine were 1.05, 1.10, and 0.75 for ascorbic acid, sodium sulfite, and sodium thiosulfate, respectively. The destructive effects of the three quenching agents on total organic halogen (TOX) followed the rank order of ascorbic acid (33.7-64.8 %) < sodium sulfite (41.6-72.8 %) < sodium thiosulfate (43.3-73.2 %), and the destructive effects on aliphatic DBPs also followed the rank order of ascorbic acid (29.5-44.5 %) < sodium sulfite (34.9-51.9 %) < sodium thiosulfate (46.9-53.2 %). For total organic chlorine (TOCl) and aliphatic DBPs, the quenching behavior itself had more significant destructive effect than the quenching agent type/dose and quenching time, but for total organic bromine (TOBr), the destructive effect caused by quenching agent type/dose and quenching time was more significant. High-dose, long-duration quenching enhanced the reduction of TOX, but had little effect on aliphatic DBPs. Additionally, the three quenching agents reduced the levels of halophenols (except for tribromophenol), while maintained or increased the levels of tribromophenol, halobenzoic/salicylic acids, and halobenzaldehydes/salicylaldehydes. To achieve adequate quenching for overall DBP analysis in chlorinated water samples, it is recommended to use ascorbic acid at a quenching agent-to-chlorine MR of 1.0 for a quenching time of < 0.5 h.

A review of research advances on disinfection strategies for biofilm control in drinking water distribution systems

The presence of biofilms in drinking water distribution systems (DWDS) is responsible for water quality deterioration and a possible source of public health risks. Different factors impact the biological stability of drinking water (DW) in the distribution networks, such as the presence and concentration of nutrients, water temperature, pipe material composition, hydrodynamic conditions, and levels of disinfectant residual. This review aimed to evaluate the current state of knowledge on strategies for DW biofilm disinfection through a qualitative and quantitative analysis of the literature published over the last decade. A systematic review method was performed on the 562 journal articles identified through database searching on Web of Science and Scopus, with 85 studies selected for detailed analysis. A variety of disinfectants were identified for DW biofilm control such as chlorine, chloramine, UV irradiation, hydrogen peroxide, chlorine dioxide, ozone, and others at a lower frequency, namely, electrolyzed water, bacteriophages, silver ions, and nanoparticles. The disinfectants can impact the microbial communities within biofilms, reduce the number of culturable cells and biofilm biomass, as well as interfere with the biofilm matrix components. The maintenance of an effective residual concentration in the water guarantees long-term prevention of biofilm formation and improves the inactivation of detached biofilm-associated opportunistic pathogens. Additionally, strategies based on multi-barrier processes by optimization of primary and secondary disinfection combined with other water treatment methods improve the control of opportunistic pathogens, reduce the chlorine-tolerance of biofilm-embedded cells, as well as decrease the corrosion rate in metal-based pipelines. Most of the studies used benchtop laboratory devices for biofilm research. Even though these devices mimic the conditions found in real DWDS, future investigations on strategies for DW biofilm control should include the validity of the promising strategies against biofilms formed in real DW networks.

Conversion of locally available materials to biochar and activated carbon for drinking water treatment

For environmental sustainability and to achieve sustainable development goals (SDGs), drinking water treatment must be done at a reasonable cost with minimal environmental impact. Therefore, treating contaminated drinking water requires materials and approaches that are inexpensive, produced locally, and effortlessly. Hence, locally available materials and their derivatives, such as biochar (BC) and activated carbon (AC) were investigated thoroughly. Several researchers and their findings show that the application of locally accessible materials and their derivatives are capable of the adsorptive removal of organic and inorganic contaminants from drinking water. The application of locally available materials such as lignocellulosic materials/waste and its thermo-chemically derived products, including BC and AC were found effective in the treatment of contaminated drinking water. Thus, this review aims to thoroughly examine the latest developments in the use of locally accessible feedstocks for tailoring BC and AC, as well as their features and applications in the treatment of drinking water. We attempted to explain facts related to the potential mechanisms of BC and AC, such as complexation, co-precipitation, electrostatic interaction, and ion exchange to treat water, thereby achieving a risk-free remediation approach to polluted water. Additionally, this research offers guidance on creating efficient household treatment units based on the health risks associated with customized adsorbents and cost-benefit analyses. Lastly, this review work discusses the current obstacles for using locally accessible materials and their thermo-chemically produced by-products to purify drinking water, as well as the necessity for technological interventions.

Effective chloramine management without "burn" in biofilm affected nitrifying tanks using a low dose of copper

This paper highlights the potential to effectively inhibit nitrification and restore chloramine levels using a low copper concentration in a biofilm-affected (surface-to-volume ratio 16 m-1) continuous-flow laboratory-scale chloraminated system. High nitrite and low chloramine containing tanks are always recovered with chlorine "burn" by water utilities. The "burn" is not only costly and operationally complex, but also compromises the water quality, public health, and customer relations. A laboratory system comprising five reactors connected in series was operated. Each reactor simulated conditions typically encountered in full-scale systems. Low amount of copper (0.1-0.2 mg-Cu L-1) was dosed once per day into nitrified reactors. At any given time, only one reactor was dosed with copper. Not only inhibition of nitrification, chloramine decay associated with bulk water, biofilm and sediments also improved. However, the improvement was quicker and more significant when the influent to the reactor contained a high chloramine and a low nitrite concentration. Ammonia oxidising microbes exhibited resilience when exposed to low copper and chloramine concentrations for an extended period. Chloramine decay due to planktonic microbes and chemical reactions in bulk water decreased more rapidly than decay attributed to biofilm and sediments. The concept "biostable residual chlorine" explained how copper and chloramine can inhibit nitrification. Once nitrification was inhibited, the chloramine supplied from upstream effectively continued to suppress downstream nitrification, and this effect lasted more than 50 days even at 22 °C. The findings could be used to develop short-term copper dosing strategies and prevent negative impacts of nitrification and breakpoint chlorination.

Association Between Arsenic Toxicity, AS3MT Gene Polymorphism and Onset of Type 2 Diabetes

Arsenic (As) exposure in drinking water has become a serious public health issue. AS3MT gene is involved in the metabolism of arsenic, so a single nucleotide polymorphism in this gene may lead to the development of type 2 diabetes in arsenic-exposed areas. This study aimed to evaluate the association of the AS3MT gene with the development of type 2 diabetes in highly arsenic-exposed areas of Punjab, Pakistan. Total 200 samples equal in number from high arsenic exposed-areas of Lahore (Nishtar) and Kasur (Mustafa Abad) were collected. rs11191439 was utilized as an influential variable to evaluate the association between arsenic metabolism and diabetes status to find a single nucleotide polymorphism in the AS3MT gene. We observed the arsenic level in drinking water of the arsenic-exposed selected areas 115.54 ± 1.23 µg/L and 96.88 ± 0.48 µg/L, respectively. The As level in the urine of diabetics (98.54 ± 2.63 µg/L and 56.38 ± 12.66 µg/L) was higher as compared to non-diabetics (77.58 ± 1.8 µg/L and 46.9 ± 8.95 µg/L) of both affected areas, respectively. Correspondingly, the As level in the blood of diabetics (6.48 ± 0.08 µg/L and 5.49 ± 1.43 µg/L) and non-diabetics (6.22 ± 0.12 µg/L and 5.26 ± 0.24 µg/L) in the affected areas. Genotyping showed significant differences in the frequencies of alleles among cases and controls. Nevertheless, notable disparities in genotype distribution were observed in SNPs rs11191439 (T/C) (P < 0.05) and when comparing T2D patients and non-diabetic control subjects. The AS3MT gene and clinical parameters show a significant association with the affected people with diabetes living in arsenic-exposed areas.

Domestic hot-water boilers harbour active thermophilic bacterial communities distinctly different from those in the cold-water supply

Running cold and hot water in buildings is a widely established commodity. However, interests regarding hygiene and microbiological aspects had so far been focussed on cold water. Little attention has been given to the microbiology of domestic hot-water installations (DHWIs), except for aspects of pathogenic Legionella. World-wide, regulations consider hot (or warm) water as 'heated drinking water' that must comply (cold) drinking water (DW) standards. However, the few reports that exist indicate presence and growth of microbial flora in DHWIs, even when supplied with water with disinfectant residual. Using flow cytometric (FCM) total cell counting (TCC), FCM-fingerprinting, and 16S rRNA-gene-based metagenomic analysis, the characteristics and composition of bacterial communities in cold drinking water (DW) and hot water from associated boilers (operating at 50 - 60 °C) was studied in 14 selected inhouse DW installations located in Switzerland and Austria. A sampling strategy was applied that ensured access to the bulk water phase of both, supplied cold DW and produced hot boiler water. Generally, 1.3- to 8-fold enhanced TCCs were recorded in hot water compared to those in the supplied cold DW. FCM-fingerprints of cold and corresponding hot water from individual buildings indicated different composition of cold- and hot-water microbial floras. Also, hot waters from each of the boilers sampled had its own individual FCM-fingerprint. 16S rRNA-gene-based metagenomic analysis confirmed the marked differences in composition of microbiomes. E.g., in three neighbouring houses supplied from the same public network pipe each hot-water boiler contained its own thermophilic bacterial flora. Generally, bacterial diversity in cold DW was broad, that in hot water was restricted, with mostly thermophilic strains from the families Hydrogenophilaceae, Nitrosomonadaceae and Thermaceae dominating. Batch growth assays, consisting of cold DW heated up to 50 - 60 °C and inoculated with hot water, resulted in immediate cell growth with doubling times between 5 and 10 h. When cold DW was used as an inoculum no significant growth was observed. Even boilers supplied with UVC-treated cold DW contained an actively growing microbial flora, suggesting such hot-water systems as autonomously operating, thermophilic bioreactors. The generation of assimilable organic carbon from dissolved organic carbon due to heating appears to be the driver for growth of thermophilic microbial communities. Our report suggests that a man-made microbial ecosystem, very close to us all and of potential hygienic importance, may have been overlooked so far. Despite consumers having been exposed to microbial hot-water flora for a long time, with no major pathogens so far been associated specifically with hot-water usage (except for Legionella), the role of harmless thermophiles and their interaction with potential human pathogens able to grow at elevated temperatures in DHWIs remains to be investigated.

An electrical- and chemical-free approach using microfilter and Ag-based catalysts for emergency drinking water treatment

In emergency cases such as disasters, supplying enough safe drinking water is one of the most urgent needs for human life. This research aimed to develop a chemical- and electricity-free drinking water treatment system based on microfiltration and catalysts of Ag and Ag-TiO2-SiO2 coated on glass spheres in both dark and sunlight conditions. The system was applied to treat raw water samples taken from five rivers in Vietnam, simulated floodwater samples with high turbidity and E. coli concentration, and real flooding water samples. The results showed the filtration unit fed with simulated floodwater generated lower fluxes and shorter working durations before chemical cleaning than that fed with normal river water. However, filtrate quality was not significantly different for these five water samples with very low values of turbidity (0-0.66 NTU), total coliform (5-19 CFU (100 mL)-1), and E. coli (0-17 CFU (100 mL)-1). The catalyst units using glass spheres coated with either Ag in dark and sunlight or Ag-TiO2-SiO2 under sunlight can completely remove E. coli and coliform as well as additionally mitigate natural organic matters. This study hence suggests the combination of microfiltration and Ag-based catalytic treatment for safe drinking water supply in emergencies, especially for flooding conditions.

GenX caused liver injury and potential hepatocellular carcinoma of mice via drinking water even at environmental concentration

Hexafluoropropylene oxide dimer acid (GenX) is an alternative to perfluorooctanoic acid (PFOA), whose environmental concentration is close to its maximum allowable value established by the US Environmental Protection Agency, so its effects on human health are of great concern. The liver is one of the most crucial target organ for GenX, but whether GenX exposure induces liver cancer still unclear. In this research project, male C57 mice were disposed to GenX in drinking water at environmental concentrations (0.1 and 10 μg/L) and higher concentrations (1 and 100 mg/L) for 14 weeks to explore its effects on liver injury and potential carcinogenicity in mice. GenX was found to cause a dose-dependent increase in the serum levels of alanine aminotransferase (ALT), aspartate aminotransferase (AST), total cholesterol (TC), and triglyceride (TG). As the content of GenX in drinking water increased, so did the concentrations of Glypican-3 (GPC-3) and detachment gamma-carboxyprothrombin (DCP), indicators of early hepatocellular cancer. GenX destroyed the boundaries and arrangements of hepatocytes, in which monocyte infiltration, balloon-like transformation, and obvious lipid vacuoles were observed between cells. Following exposure to GenX, Masson sections revealed a significant quantity of collagen deposition in the liver. Alpha-feto protein (AFP), vascular endothelial growth factor (VEGF), Ki67, matrix metalloproteinase 2 (MMP-2) and matrix metalloproteinase 9 (MMP-9) gene expression increased in a dose-dependent manner in the treatment group relative to the control group. In general, drinking water GenX exposure induced liver function impairment, elevated blood lipid level, caused liver pathological structure damage and liver fibrosis lesions, changed the liver inflammatory microenvironment, and increased the concentration of liver-related tumor indicator even in the environmental concentration, suggesting GenX is a potential carcinogen.

Inoculation with adapted bacterial communities promotes development of full scale slow sand filters for drinking water production

Gravity-driven filtration through slow sand filters (SSFs) is one of the oldest methods for producing drinking water. As water passes through a sand bed, undesired microorganisms and chemicals are removed by interactions with SSF biofilm and its resident microbes. Despite their importance, the processes through which these microbial communities form are largely unknown, as are the factors affecting these processes. In this study, two SSFs constructed using different sand sources were compared to an established filter and observed throughout their maturation process. One SSF was inoculated through addition of sand scraped from established filters, while the other was not inoculated. The operational and developing microbial communities of SSFs, as well as their influents and effluents, were studied by sequencing of 16S ribosomal rRNA genes. A functional microbial community resembling that of the established SSF was achieved in the inoculated SSF, but not in the non-inoculated SSF. Notably, the non-inoculated SSF had significantly (p < 0.01) higher abundances of classes Armatimonadia, Elusimicrobia, Fimbriimonadia, OM190 (phylum Planctomycetota), Parcubacteria, Vampirivibrionia and Verrucomicrobiae. Conversely, it had lower abundances of classes Anaerolineae, Bacilli, bacteriap25 (phylum Myxococcota), Blastocatellia, Entotheonellia, Gemmatimonadetes, lineage 11b (phylum Elusimicrobiota), Nitrospiria, Phycisphaerae, subgroup 22 (phylum Acidobacteriota) and subgroup 11 (phylum Acidobacteriota). Poor performance of neutral models showed that the assembly and dispersal of SSF microbial communities was mainly driven by selection. The temporal turnover of microbial species, as estimated through the scaling exponent of the species-time relationship, was twice as high in the non-inoculated filter (0.946 ± 0.164) compared to the inoculated filter (0.422 ± 0.0431). This study shows that the addition of an inoculum changed the assembly processes within SSFs. Specifically, the rate at which new microorganisms were observed in the biofilm was reduced. The reduced temporal turnover may be driven by inoculating taxa inhibiting growth, potentially via secondary metabolite production. This in turn would allow the inoculation community to persist and contribute to SSF function.

Nitrate exposure from drinking water and dietary sources among Iowa farmers using private wells

Nitrate levels are increasing in water resources across the United States and nitrate ingestion from drinking water has been associated with adverse health risks in epidemiologic studies at levels below the maximum contaminant level (MCL). In contrast, dietary nitrate ingestion has generally been associated with beneficial health effects. Few studies have characterized the contribution of both drinking water and dietary sources to nitrate exposure. The Agricultural Health Study is a prospective cohort of farmers and their spouses in Iowa and North Carolina. In 2018-2019, we assessed nitrate exposure for 47 farmers who used private wells for their drinking water and lived in 8 eastern Iowa counties where groundwater is vulnerable to nitrate contamination. Drinking water and dietary intakes were estimated using the National Cancer Institute Automated Self-Administered 24-Hour Dietary Assessment tool. We measured nitrate in tap water and estimated dietary nitrate from a database of food concentrations. Urinary nitrate was measured in first morning void samples in 2018-19 and in archived samples from 2010 to 2017 (minimum time between samples: 2 years; median: 7 years). We used linear regression to evaluate urinary nitrate concentrations in relation to total nitrate, and drinking water and dietary intakes separately. Overall, dietary nitrate contributed the most to total intake (median: 97 %; interquartile range [IQR]: 57-99 %). Among 15 participants (32 %) whose drinking water nitrate concentrations were at/above the U.S. Environmental Protection Agency MCL (10 mg/L NO3-N), median intake from water was 44 % (IQR: 26-72 %). Total nitrate intake was the strongest predictor of urinary nitrate concentrations (R2 = 0.53). Drinking water explained a similar proportion of the variation in nitrate excretion (R2 = 0.52) as diet (R2 = 0.47). Our findings demonstrate the importance of both dietary and drinking water intakes as determinants of nitrate excretion.

Direct potable reuse and birth defects prevalence in Texas: An augmented synthetic control method analysis of data from a population-based birth defects registry

Background

Direct potable reuse (DPR) involves adding purified wastewater that has not passed through an environmental buffer into a water distribution system. DPR may help address water shortages and is approved or is under consideration as a source of drinking water for several water-stressed population centers in the United States, however, there are no studies of health outcomes in populations who receive DPR drinking water. Our objective was to determine whether the introduction of DPR for certain public water systems in Texas was associated with changes in birth defect prevalence.

Methods

We obtained data on maternal characteristics for all live births and birth defects cases regardless of pregnancy outcome in Texas from 2003 to 2017 from the Texas Birth Defects Registry and birth and fetal death records. The ridge augmented synthetic control method was used to model changes in birth defect prevalence (per 10,000 live births) following the adoption of DPR by four Texas counties in mid-2013, with county-level data on maternal age, percent women without a high school diploma, percent who identified as Hispanic/Latina or non-Hispanic/Latina Black, and rural-urban continuum code as covariates.

Results

There were nonstatistically significant increases in prevalence of all birth defects collectively (average treatment effect in the treated = 53.6) and congenital heart disease (average treatment effect in the treated = 287.3) since June 2013. The estimated prevalence of neural tube defects was unchanged.

Conclusions

We estimated nonstatistically significant increases in birth defect prevalence following the implementation of DPR in four West Texas counties. Further research is warranted to inform water policy decisions.

Involvement of functional metabolism promotes the enrichment of antibiotic resistome in drinking water: Based on the PICRUSt2 functional prediction

Biofilters are the important source and sink of antibiotic resistance genes (ARGs) and antibiotic resistance bacteria (ARB) in the drinking water. Current studies generally ascribed the prevalence of BAR in biofilter from the perspective of gene behavior, i.e. horizontal gene transfer (HGT), little attentions have been paid on the ARGs carrier- ARB. In this study, we proposed the hypothesis that ARB participating in pollutant metabolism processes and becoming dominant is an important way for the enrichment of ARGs. To verify this, the antibiotic resistome and bacterial functional metabolic pathways of a sand filter was profiled using heterotrophic bacterial plate counting method (HPC), high-throughput qPCR, Illumina Hiseq sequencing and PICRUSt2 functional prediction. The results illustrated a significant leakage of ARB in the effluent of the sand filter with an average absolute abundance of approximately 102-103 CFU/mL. Further contribution analysis revealed that the dominant genera, such as Acinetobacter spp., Aeromonas spp., Elizabethkingia spp., and Bacillus spp., were primary ARGs hosts, conferring resistance to multiple antibiotics including sulfamethoxazole, tetracycline and β-lactams. Notably, these ARGs hosts were involved in nitrogen metabolism, including extracellular nitrate/nitrite transport and nitrite reduction, which are crucial in nitrification and denitrification in biofilters. For example, Acinetobacter spp., the dominant bacteria in the filter (relative abundance 69.97 %), contributed the majority of ARGs and 53.79 % of nitrite reduction function. That is, ARB can predominate by participating in the nitrogen metabolism pathways, facilitating the enrichment of ARGs. These findings provide insights into the stable presence of ARGs in biofilters from a functional metabolism perspective, offering a significant supplementary to the mechanisms of the emergence, maintenance, and transmission of BARin drinking water.

Recent advances in microplastic removal from drinking water by coagulation: Removal mechanisms and influencing factors

Microplastics (MPs) are emerging contaminants that are widely detected in drinking water and pose a potential risk to humans. Therefore, the MP removal from drinking water is a critical challenge. Recent studies have shown that MPs can be removed by coagulation. However, the coagulation removal of MPs from drinking water remains inadequately understood. Herein, the efficiency, mechanisms, and influencing factors of coagulation for removing MPs from drinking water are critically reviewed. First, the efficiency of MP removal by coagulation in drinking water treatment plants (DWTPs) and laboratories was comprehensively summarized, which indicated that coagulation plays an important role in MP removal from drinking water. The difference in removal effectiveness between the DWTPs and laboratory was mainly due to variations in treatment conditions and limitations of the detection techniques. Several dominant coagulation mechanisms for removing MPs and their research methods are thoroughly discussed. Charge neutralization is more relevant for small-sized MPs, whereas large-sized MPs are more dependent on adsorption bridging and sweeping. Furthermore, the factors influencing the efficiency of MP removal were jointly analyzed using meta-analysis and a random forest model. The meta-analysis was used to quantify the individual effects of each factor on coagulation removal efficiency by performing subgroup analysis. The random forest model quantified the relative importance of the influencing factors on removal efficiency, the results of which were ordered as follows: MPs shape > Coagulant type > Coagulant dosage > MPs concentration > MPs size > MPs type > pH. Finally, knowledge gaps and potential future directions are proposed. This review assists in the understanding of the coagulation removal of MPs, and provides novel insight into the challenges posed by MPs in drinking water.

Considering a Utility-Centric Framework Based on "Minimum Orthophosphate" Criteria for Mitigation of Elevated Cuprosolvency in Drinking Water

Gaps in the United States Environmental Protection Agency (US EPA) Lead and Copper Rule (LCR) leave some consumers and their pets vulnerable to high cuprosolvency in drinking water. This study seeks to help proactive utilities who wish to mitigate cuprosolvency problems through the addition of orthophosphate corrosion inhibitors. The minimum doses of orthophosphate necessary to achieve acceptable cuprosolvency in relatively new copper pipe were estimated as a function of alkalinity via linear regressions for the 90th, 95th, and 100th percentile copper tube segments (R2 > 0.98, n = 4). Orthophosphate was very effective at reducing cuprosolvency in the short term but, in some cases, resulted in higher long-term copper concentrations than the corresponding condition without orthophosphate. Alternatives to predicting "long-term" results for copper tubes using simpler bench tests starting with fresh Cu(OH)2 solids showed promise but would require further vetting to overcome limitations such as maintaining water chemistry and orthophosphate residuals and to ensure comparability to results using copper tube.

Physico-chemical treatments for the removal of cyanotoxins from drinking water: Current challenges and future trends

Cyanobacteria are highly prevalent blue-green algae that grow in stagnant and nutrient-rich water bodies. Environmental conditions, such as eutrophication and human activities, increased the cyanobacterial blooms in freshwater resources worldwide. The excessive bloom formation has also resulted in an alarming surge of cyanobacterial toxins. Prolonged exposure to cyanotoxins is a potential threat to natural ecosystems, animal and human health by the spoilage of the quality of bathing and drinking water. Various molecular and analytical methods have been proposed to monitor their occurrence and understand their global distribution. Moreover, different physical, chemical, and biological approaches have been employed to control cyanobacterial blooms and their toxins to mitigate their occurrence. Numerous strategies have been engaged in drinking water treatment plants (DWTPs). However, the degree of treatment varies greatly and is primarily determined by the source, water properties, and operating parameters such as temperature, pH, and cyanotoxin variants and levels. A comprehensive compilation of methods, from traditional approaches to more advanced oxidation processes (AOPs), are presented for the removal of intracellular and extracellular cyanotoxins. This review discusses the effectiveness of various physicochemical operations and their limitations in a DWTP, for the removal of various cyanotoxins. These operations span from simple to advanced treatment levels with varying degrees of effectiveness and differing costs of implementation. Furthermore, mitigation measures applied in other toxin systems have been considered as alternative strategies.

Distribution characteristics and transformation mechanism of per- and polyfluoroalkyl substances in drinking water sources: A review

Per- and polyfluoroalkyl substances (PFASs) have raised significant concerns within the realm of drinking water due to their widespread presence in various water sources. This prevalence poses potential risks to human health, ecosystems, and the safety of drinking water. However, there is currently a lack of comprehensive reviews that systematically categorize the distribution characteristics and transformation mechanisms of PFASs in drinking water sources. This review aims to address this gap by concentrating on the specific sources of PFASs contamination in Chinese drinking water supplies. It seeks to elucidate the migration and transformation processes of PFASs within each source, summarize the distribution patterns of PFASs in surface and subsurface drinking water sources, and analyze how PFASs molecular structure, solubility, and sediment physicochemical parameters influence their presence in both the water phase and sediment. Furthermore, this review assesses two natural pathways for PFASs degradation, namely photolysis and biodegradation. It places particular emphasis on understanding the degradation mechanisms and the factors that affect the breakdown of PFASs by microorganisms. The ultimate goal is to provide valuable insights for the prevention and control of PFAS contamination and the assurance of drinking water quality.

Deciphering the dynamics and driving mechanisms of high-risk antibiotic resistome in size-fractionated bacterial community during drinking water chlorination via metagenomic analysis

To reveal the impact of chlorination on the high-risk resistome in size-fractionated bacterial community, we employed metagenomic approaches to decipher dynamics of high-risk antibiotic resistance genes (ARGs) and driving mechanisms in the free-living and particle-associated fractions within a full-scale drinking water treatment system. Our results revealed that chlorination significantly increased the relative abundance of high-risk ARGs in the free-living fraction to 0.33 ± 0.005 copies/cell (cpc), bacitracin and chloramphenicol resistance types were major contributors. Furthermore, chlorination significantly increased the relative abundance of mobile genetic elements (MGEs) in the free-living fraction, while decreasing it in the particle-associated fraction. During chlorination, size-fractionated bacterial communities varied considerably. Multiple statistical analyses highlighted the pivotal role of the bacterial community in altering high-risk ARGs in both the free-living and particle-associated fractions, while MGEs had a more pronounced impact on high-risk ARGs in the free-living fraction. Specifically, the enrichment of pathogenic hosts, such as Comamonas and Pseudomonas, led to an increase in the abundance of high-risk ARGs. Concurrently, MGEs exhibited significant correlations with high-risk ARGs, indicating the potential of horizontal transfer of high-risk ARGs. These findings provide novel insights for mitigating antibiotic resistance risk by considering different bacterial fractions and respective risk ranks in drinking water.

Optimizing backwash control using data on seasonal changes in the invertebrate community of granular activated carbon filters

Problems associated with the colonization and leakage of invertebrates in the granular activated carbon (GAC) filters of waterworks have received increased attention in recent years. To study the effect of environmental factors and water quality on invertebrate abundances, and the backwash control for minimizing invertebrate abundance. A survey of the invertebrate community of GAC filters was carried out monthly from March 2021 to May 2022. A pilot-scale GAC system established in the laboratory alongside a lake, with a volume of 35.3 L. 45 invertebrate species were detected, and 40 of these were rotifers. Significant variation in abundance was observed among seasons before and after GAC filtration, the average invertebrate abundance in the inlet water was 11.1 times that in the filtrate. The GAC filter contained invertebrates that might be responsible for the large number of organisms in the filtrate. Invertebrate abundance in the GAC filter decreased gradually with the carbon layer depth, which the mean invertebrate abundances were 6,926, 5,232, and 3818 ind./kg in the top layer (TL), middle layer (ML), and bottom layer (BL), respectively. Invertebrate abundance was correlated with water temperature and varied seasonally. Among eight water quality parameters, chlorophyll a (Chla) and the total plate count (TPC) were most significantly correlated with invertebrate abundance. According to the statistical modeling and the optimization process of response surface methodology (RSM). The predicted optimal values were a flow rate of 6.36 L/h, a backwash cycle of 3.26 d, and a backwash intensity of 14.97 L/(m2·s) for a minimum invertebrate abundance of 3013 ind./kg in the GAC filter. To maintain invertebrate abundance within an acceptable range, some of these measures might need to be modified depending on the actual conditions.

Endocrine disrupting chemicals in Italian drinking water systems: Insights from a three-year investigation combining chemical and effect-based tools

Drinking water quality can be compromised by endocrine-disrupting chemicals (EDCs). Three phenolic compounds [bisphenol A (BPA), nonylphenol (NP), and 4-octylphenol (OP)] and three hormones [17β-estradiol (E2), estrone (E1), and 17α-ethinylestradiol (EE2)] were analyzed as EDCs potentially occurring in source and drinking water from three full-scale drinking water treatment plants (DWTPs) in the Romagna area (Italy) by a combined approach of HPLC-MS/MS target analysis and effect-based tests for estrogenicity and genotoxicity. The EDC removal efficiency was evaluated at different steps along the treatment process in the most advanced DWTP. NP prevailed in all samples, followed by BPA. Sporadic contamination by OP and E1/E2 appeared only in the source waters; EE2 was never detected. No estrogenic or genotoxic activity was found, except for two samples showing estrogenicity well below the effect-based trigger value suggested for drinking water safety (0.9 ng/L EEQ). BPA and NP levels were largely below the threshold value; however, increases were observed after the intermediate steps of the treatment chain. The good quality of the water relied on the last step, i.e. the activated carbon filtration. DWTPs may represent an extra source of EDCs and monitoring chemical occurrence at all steps of the process is advisable to improve efficiency.

Embedding Fe(0) electrocoagulation in a biologically active As(III) oxidising filter bed

Long-term consumption of groundwater containing elevated levels of arsenic (As) can have severe health consequences, including cancer. To effectively remove As, conventional treatment technologies require expensive chemical oxidants to oxidise neutral arsenite (As(III)) in groundwater to negatively charged arsenate (As(V)), which is more easily removed. Rapid sand filter beds used in conventional aeration-filtration to treat anaerobic groundwater can naturally oxidise As(III) through biological processes but require an additional step to remove the generated As(V), adding complexity and cost. This study introduces a novel approach where As(V), produced through biological As(III) oxidation in a sand filter, is effectively removed within the same filter by embedding and operating an iron electrocoagulation (FeEC) system inside the filter. Operating FeEC within the biological filter achieved higher As(III) removal (81 %) compared to operating FeEC in the filter supernatant (67 %). This performance was similar to an analogous embedded-FeEC system treating As(V)-contaminated water (85 %), confirming the benefits of incorporating FeEC in a biological bed for comparable As(III) and As(V) removal. However, operating FeEC in the sand matrix consumed more energy (14 Wh/m3) compared to FeEC operated in a water matrix (7 Wh/m3). The efficiency of As removal increased and energy requirements decreased in such embedded-FeEC systems by deep-bed infiltration of Fe(III)-precipitates, which can be controlled by adjusting flow rate and pH. This study is one of the first to demonstrate the feasibility of embedding FeEC systems in sand filters for groundwater arsenic removal. Such systems capitalise on biological As(III) oxidation in aeration-filtration, effectively eliminating As(V) within the same setup without the need for chemicals or major modifications.

Water Safety Practices Along the Water Service Chain in Addis Ababa: A Cross-Sectional Study in a Cosmopolitan City

This study investigated water safety practices and risk levels along Addis Ababa's water supply service chain. The data came from 23 random woredas, 384 random households, 115 microbiological water quality tests, and diagnostic inspections from source to point of use. Findings from this study indicate that the surface water sources (53%) and the water source catchments (62%) are characterized by very high-risk and high risk contamination levels respectively. Conversely, the water treatment process (5%) and temporary reservoir (20%) indicates a low risk level. Whereas the water distribution system (40%), water source boreholes (44%), and Household level (29%) water safety practices are identified as medium risk levels. The microbial analysis of the drinking water at the source and point of use indicated low (<11 CFU/100 ml) to high levels (>100 CFU/100 ml) of risk with significant levels of contamination at the household level. Moreover, the household-level water safety practice assessment revealed intermediate to very high levels of risks. The Chi2 test shows that water supply type is significantly associated with occupation(X2(12,384) = 23.44, P < .05) and education(X2(8,384) = 15.4, P < .05). Multinomial regression analysis also showed better occupation is associated with increased access to safe bottled water compared to safe piped water on premises. It can be concluded that the water safety practice encountered low to very high levels of risk of contamination at different components along the water supply service chain and the household level. This study suggests ways to improve Addis Ababa residents' health and well-being through water safety interventions. These include safeguarding water sources, supporting local safe water businesses, providing household water treatment, and handling options, and addressing the barriers and incentives for adopting safe water practices.

Linkage of in-refrigerator water dispensing systems to elevated exposure to microbial contamination at the microbiome scale

In-refrigerator water dispensing systems are ubiquitous in residential homes with tap water as the inflow. Passage through these systems resulted in significant microbial growth in the water, with the abundance of potential opportunistic pathogens Mycobacterium and Pseudomonas increasing by 8,053- and 221-fold, respectively. Elevated exposure to microbial contaminants linked to in-refrigerator water dispensing systems may represent a significant public health concern.

A novel method for multi-pollutant monitoring in water supply systems using chemical machine vision

Drinking water is vital for human health and life, but detecting multiple contaminants in it is challenging. Traditional testing methods are both time-consuming and labor-intensive, lacking the ability to capture abrupt changes in water quality over brief intervals. This paper proposes a direct analysis and rapid detection method of three indicators of arsenic, cadmium, and selenium in complex drinking water systems by combining a novel long-path spectral imager with machine learning models. Our technique can obtain multiple parameters in about 1 s. The experiment involved setting up samples from various drinking water backgrounds and mixed groups, totaling 9360 injections. A raw visible light source ranging from 380 to 780 nm was utilized, uniformly dispersing light into the sample cell through a filter. The residual beam was captured by a high-definition camera, forming a distinctive spectrum. Three deep learning models-ResNet-50, SqueezeNet V1.1, and GoogLeNet Inception V1-were employed. Datasets were divided into training, validation, and test sets in a 6:2:2 ratio, and prediction performance across different datasets was assessed using the coefficient of determination and root mean square error. The experimental results show that a well-trained machine learning model can extract a lot of feature image information and quickly predict multi-dimensional drinking water indicators with almost no preprocessing. The model's prediction performance is stable under different background drinking water systems. The method is accurate, efficient, and real-time and can be widely used in actual water supply systems. This study can improve the efficiency of water quality monitoring and treatment in water supply systems, and the method's potential for environmental monitoring, food safety, industrial testing, and other fields can be further explored in the future.

Antibiotic resistance genes alterations in murine guts microbiome are associated with different types of drinking water

Antibiotic resistance genes (ARGs) are emerging contaminants threatening public health and commonly found in drinking water. However, the effect of different types of drinking water on ARG alterations in the gut microbiome is unclear. This study examines this issue in murine models in three phases (phase I: acclimation using ddH2O; phase II: treatment using different types of water, i.e. river water (RW), tap water (TW) and commercial bottled water (CBW); and phase III: recovery using ddH2O) using high-throughput qPCR and 16S rRNA amplicon sequencing. Results reveal that exposure to different types of drinking water could lead to significant changes in the gut microbiome, mobile genetic elements (MGEs), and ARGs. In phase II, treatment of RW and TW significantly increased the abundance of aminoglycoside and tetracycline resistance genes in mice guts (P < 0.01). In the recovery phase, consuming distilled water was found to restore ARG profiles to a certain extent in mice guts. Procrustes, network, redundancy and variation partitioning analysis indicated that ARG alterations in mice guts might relate to MGEs and bacterial communities. Our work suggests that the type of drinking water consumed may play a crucial role in shaping ARGs in gut microbiomes, emphasizing the urgent need for access to clean drinking water to mitigate the growing threat of antimicrobial resistance.

Quantitative health risk assessment of microbial hazards from water sources for community and self-supply drinking water systems

In low and medium income countries (LMIC) drinking water sources (wells and boreholes) often contain a high number of pathogenic microorganisms, that can pose significant human and environmental health risks. In this study, a quantitative microbial risk assessment approach based on existing literature was conducted to evaluate and compare the quantitative health risks associated with different age groups using various drinking water supply systems. Results showed that both community-supply and self-supply modes exhibit similar levels of risk. However, the self-supply water source consistently showed higher risks compared to the community-supply one. Borehole water was found to be a more suitable option than well water, consistently showing between 5 and 8 lower health risks for E. coli and fecal coliform levels, respectively. The sensitivity analysis further showed the importance of prioritizing the reduction of E. coli concentration in well water and fecal coliform concentration in borehole water. This study offers a fresh perception on quantifying the impact of exposure concentration and age groups, shedding light on how they affect environmental health risks. These findings provide valuable insights for stakeholders involved in the management and protection of water sources.

Gut microbiota deficiency aggravates arsenic-induced toxicity by affecting bioaccumulation and biotransformation in C57BL/6J mice

Gut microbiome can influence the arsenic metabolism in mammals. Confusingly, gut microbiome was found to both mitigate and exacerbate arsenic toxicity. In this study, the role of gut microbiota in arsenic bioaccumulation, biotransformation, and organ toxicity in C57BL/6J mice was investigated. Gut microbiota deficiency model was established by antibiotics (Ab) cocktail AVNM. Conventional and gut microbiota deficiency mice were exposed to NaAsO2 for 4 weeks. Comparing with Ab-treated mice, the total arsenic (tAs) in the tissues was significantly reduced in conventional mice, which was opposed to the results of those in feces. Interestingly, dimethyl arsenite (DMA) was the most abundant metabolite in the feces of Ab-treated mice, while arsenic acid (AsV) had the highest proportion in the feces of conventional mice with approximately 16-fold than that in Ab-treated mice, indicating the critical role of gut microbiota in metabolizing arsenious acid (AsIII) to AsV. Additionally, the liver and kidney in Ab-treated mice showed more severe pathological changes and apoptosis. The significant increased level of ionized calcium-binding adapter molecule 1 (IBA-1) was also found in the brains of Ab-treated mice. Our results indicated that gut microbiota protected the host from arsenic-induced toxicity in liver, kidney, and brain by reducing the arsenic accumulation.

Long-term cancer and overall mortality associated with drinking water nitrate in the United States

OBJECTIVES

Nitrate is a probable carcinogen regulated in drinking water by the US Environmental Protection Agency (EPA) to a maximum contaminant level (MCL) of 10 mg/L nitrate-nitrogen (NO3-N; equivalent to 44.3 mg/L NO3). We aimed to determine the association of US drinking water nitrate levels with overall as well as cardiovascular, cancer, and other cause mortality.

STUDY DESIGN

This study used a population-based retrospective cohort design.

METHODS

We analyzed data from 2029 participants of the 2005-2006 National Health and Nutrition Examination Survey followed for mortality until 2019 for a median of 13.9 years. We used Cox proportional hazards regression to estimate the hazard ratio (HR) and 95% confidence interval (CI) for mortality associated with drinking water nitrate, adjusting for covariates that included socio-economic factors and pack-years of cigarette smoking.

RESULTS

Drinking water nitrate was detected in 50.8 % of the samples, had a median concentration of 0.77 mg/L NO3, and was above US EPA MCL in 0.4 % of participants. In adjusted analysis, drinking water nitrate detection was associated with 73 % higher cancer mortality (HR: 1.73, 95% CI: 1.19-2.51), whereas a 10-fold increase in drinking water nitrate levels was associated with 69 % higher cancer mortality (HR: 1.69, 95% CI: 1.24-2.31) and 21 % higher overall mortality (HR: 1.21, 95% CI: 1.00-1.46). Drinking water nitrate below EPA MCL was still associated with higher cancer mortality (HR: 1.61, 95% CI: 1.07-2.43 per 10-fold increase and HR: 1.61, 95% CI: 1.08-2.42 for detection).

CONCLUSIONS

Levels of drinking water nitrate may be an overlooked contributor to cancer mortality in the United States.

Reduced burden of Arsenic-Related cancers after water mitigation in Taiwan

BACKGROUND

Epidemiological evidence has demonstrated an association between arsenic in drinking water and increased cancer incidence. This population-based study investigates the impact of a tap water supply system installation in Blackfoot disease-endemic regions of Taiwan on cancer incidence.

METHODS

By using the Taiwan Cancer Registry dataset, we enrolled patients aged 40-84 diagnosed with arsenic-related cancers, including hepatocellular carcinoma, small and squamous cell lung cancer, Bowen's disease, basal and squamous cell skin cancer, urothelial bladder cancer, and upper tract urothelial carcinoma between 1995 and 2019. Random-effects age-period-cohort models were used to estimate the cancer incidence data, and a stabilized kriging method was employed to interpolate incidence rates to more precise spatiotemporal units.

RESULTS

The results showed that the age-standardized incidence rates of all six types of studied cancers were consistently higher in Blackfoot disease-endemic areas than those in other areas from 1995 to 2019. However, the gap in incidence rates between Blackfoot disease-endemic areas and the remaining regions began to narrow approximately after the 1960 birth cohort when the tap water supply system installation commenced. For small and squamous cell lung cancer, Bowen's disease, and urothelial bladder cancer, the excess incidence rates sharply declined to null for those born after the year of arsenic mitigation. For upper tract urothelial carcinoma, the excess incidence rates decreased more gradually for those born after the year of arsenic mitigation. For hepatocellular carcinoma and basal and squamous cell skin cancer, the excess incidence rates remained constant. Spatiotemporal clusters of high incidence rates were identified in the core townships of Blackfoot disease-endemic areas. These clusters began to dissipate mainly after the 1960 birth cohort.

CONCLUSION

Arsenic mitigation from drinking water in Taiwan is associated with a reduced burden of small and squamous cell lung cancers, Bowen's disease, urothelial bladder cancer, and upper tract urothelial carcinoma.

Toward the autonomous flushing of building plumbing: Characterizing oxidation-reduction potential and temperature sensor dynamics

Manual flushing of building plumbing is commonly used to address water quality issues that arise from water stagnation. Autonomous flushing informed by sensors has the potential to aid in the management of building plumbing, but a number of knowledge gaps hinder its application. This study evaluates autonomous flushing of building plumbing with online sensor and actuator nodes deployed under kitchen sinks in five residential houses. Online oxidation-reduction potential (ORP) and temperature data were collected for nine weeks during the winter and summer in houses with both free chlorine and chloramine. ORP levels in houses with free chlorine residuals decreased after overnight stagnation. The overnight decrease in ORP was not observed when tap water was automatically flushed for five minutes at 6:00 h every morning. ORP levels in houses with chloramine residuals did not decrease consistently after overnight stagnation, and daily automated flushes did not have an observable effect on the ORP signals. Additional laboratory experiments were carried out to evaluate ORP signals during chlorine decay and after incremental changes in chlorine, as would be expected in building plumbing conditions. Results from the lab and field deployments suggest on-line ORP sensors may be used to detect free chlorine decay due to stagnating water, but are not as effective in detecting chloramine decay. However, field results also suggest ORP may not respond as expected on a timely manner after free chlorine or chloramine have been restored, hindering their applicability in developing control algorithms. In this paper we tested twice-daily five-minute automatic flushing and found that it counteracts water quality degradation associated with overnight stagnation in free chlorine systems. An automatic sensor-based flushing is proposed using online temperature sensor data to determine when flushing has reached water from the main. The results suggest that flushing informed by temperature sensors can reduce the flushing time by 46 % compared to the preset five-minute static flush.

Performance of public drinking water purifiers in control of trihalomethanes, antibiotics and antibiotic resistance genes

Point-of-use water purifiers are widely applied as a terminal treatment device to produce drinking water with high quality. However, concerns are raised regarding low efficiency in eliminating emerging organic pollutants. To enhance our understanding of the reliability and potential risks of water purifiers, the removal of trihalomethanes, antibiotics, and antibiotic resistance genes (ARGs) in four public water purifiers was investigated. In the four public water purifiers in October and November, the removal efficiencies of trichloromethane (TCM) and bromodichloromethane (BDCM) were 15%-69% (averagely 37%) and 6%-44% (averagely 23%). The levels of TCM and BDCM were lowered by all water purifiers in October and November, but accelerated in effluent compared to the influent in one public water purifier in December. The removal efficiencies of twelve antibiotics greatly varied with species and time. Out of twelve sampling cases, the removal efficiencies of total antibiotics were 25%-75% in ten cases. In the other two cases, very low removal efficiency (6%) or higher levels of antibiotics present in effluent compared to the influent were observed. Two public water purifiers effectively remove ARGs from water, with log removal rates of 0.45 log-3.89 log. However, in the other two public water purifiers, the ARG abundance accidently increased in the effluents. Overall, public water purifiers were more effective in removing antibiotics and ARGs compared to household water purifiers, but less or equally effective in removing trihalomethanes. Both public and household water purifiers could be contaminated and release the accumulated micro-pollutants or biofilm-related pollutants into effluent. The production frequency and standing time of water within water purifiers can impact the internal contamination and purification efficacy.