The hygroscopic power of amorphous cellulose: a modeling study

Multiscale dynamics and molecular mobility in cellulose-rich materials

Cellulose, an abundant biopolymer in nature as a structural component of plant cell walls, has a native semi-crystalline structure in which the arrangement of amorphous-crystalline domains governs its key properties such as mechanical and physico-chemical properties. The performance of the material in different situations is shaped by molecular mobility, which affects attributes such as mechanical properties, chemical reactivity, and water absorption. Nevertheless, it is difficult to investigate experimentally the structural and dynamic properties of cellulose-rich materials. This is especially the case for the glass transition, which impacts its quality and properties. This experimental challenge is notably evidenced by the considerable variability in data across the literature. The purpose of this study is to offer a comprehensive multi-scale exploration of dynamics within cellulose-rich materials, emphasizing literature data on cellulose glass transition and molecular relaxations, and providing insights into methods for characterizing their physical state and underscoring the impact of water-cellulose interactions on molecular mobility in these systems. The promising results obtained using multiple approaches bring out the importance of combining methods to achieve a more accurate and detailed understanding of the complex thermal transition in cellulose materials, particularly when considering the influence of water on their thermal dynamics and properties.

Cellulose Dissolution, Modification, and the Derived Hydrogel: A Review

The cellulose-based hydrogel has occupied a pivotal position in almost all walks of life. However, the native cellulose can not be directly used for preparing hydrogel due to the complex non-covalent interactions. Some literature has discussed the dissolution and modification of cellulose but has yet to address the influence of the pretreatment on the as-prepared hydrogels. Firstly, the "touching" of cellulose by derived and non-derived solvents was introduced, namely, the dissolution of cellulose. Secondly, the "conversion" of functional groups on the cellulose surface by special routes, which is the modification of cellulose. The above-mentioned two parts were intended to explain the changes in physicochemical properties of cellulose by these routes and their influences on the subsequent hydrogel preparation. Finally, the "reinforcement" of cellulose-based hydrogels by physical and chemical techniques was summarized, viz., improving the mechanical properties of cellulose-based hydrogels and the changes in the multi-level structure of the interior of cellulose-based hydrogels.

Effect of Dissolution Time on the Development of All-Cellulose Composites Using the NaOH/Urea Solvent System

Innovative and sustainable all-cellulose composites (ACCs) can be obtained by partial dissolution of cellulosic fibers and regeneration of the dissolved fraction. Among cellulose solvents, sodium hydroxide/urea solutions are recognized as promising low-environmental impact systems. In this work, filter paper (FP) was dissolved with a 7 wt% NaOH/12 wt% urea aqueous solution, kept at −18 °C for different time intervals, regenerated with distilled water and finally dried under different conditions. The developed films were characterized in terms of morphology, porosity, optical properties, crystalline structure, hydration and mechanical properties. The porosity of the composites decreased with dissolution time due to the progressive filling of voids as the cellulosic fibers’ surface skin layer was dissolved and regenerated. Samples treated for 4 h showed the minimum values of porosity and opacity, high hydration and a substantial change from cellulose I to cellulose II. Hot pressing during drying led to relevant improvements in ACCs stiffness and strength values.

Fast and Filtration-Free Method to Prepare Lactic Acid-Modified Cellulose Nanopaper

Dewatering in the preparation of cellulose nanopapers can take up to a few hours, which is a notable bottleneck in the commercialization of nanopapers. As a solution, we report a filtration-free method that is capable of preparing lactic acid-modified cellulose nanopapers within a few minutes. The bleached cellulose nanofibers (CNFs), obtained using a Masuko grinder, were functionalized by sonication-assisted lactic acid modification and centrifuged at 14 000 rpm to achieve a doughlike, concentrated mass. The concentrated CNFs were rolled into a wet sheet and dried in a vacuum drier to obtain nanopapers. The nanopaper preparation time was 10 min, which is significantly faster than the earlier time period reported in the literature (up to a few hours of preparation time). The mechanical properties of nanopaper were comparable to the previous values reported for nanopapers. In addition, the method was successfully used to prepare highly conductive functional nanopapers containing carboxylated multiwalled carbon nanotubes.

Impact of Two-Dimensional Particle Size Distribution on Estimation of Water Vapor Diffusivity in Micrometric Size Cellulose Particles

This work aims at assessing the impact of two-dimensional particle size distribution (2D-PSD) on the identification of water vapor diffusivity in micrometric size cellulose particles displaying a size aspect ratio lower than 2 and a cylindrical shape. First, different methodologies to obtain the two-dimensional (2D) particle size distribution (diameter versus length) were compared, based on image analysis. Then, experimental sorption kinetics were obtained by using a quartz crystal microbalance (QCM) coupled with a water vapor adsorption system. Diffusivity values were estimated when considering either the 2D-PSD or global descriptors, such as the mean or median diameter and length of particles. Results revealed that the use of an analytical approach when considering the 2D mean-PSD or the median-PSD was the most accurate way to get diffusivity values at the scale of particles in a polydisperse sample of cellulose particles. Following this approach, a water vapor apparent diffusivity of 3.1 × 10⁻¹² ± 2.3 × 10⁻¹² m²·s⁻¹ was found for the considered cellulose sample. Neglecting PSD in diffusivity estimation led to an underestimation of a factor of 2. This procedure could be extended for all the polydisperse samples in order to have an accurate estimation of water vapor diffusivity at the scale of single particles.

Dehydration of bacterial cellulose and the water content effects on its viscoelastic and electrochemical properties

Bacterial cellulose (BC) has interesting properties including high crystallinity, tensile strength, degree of polymerisation, water holding capacity (98%) and an overall attractive 3D nanofibrillar structure. The mechanical and electrochemical properties can be tailored upon incomplete BC dehydration. Under different water contents (100, 80 and 50%), the rheology and electrochemistry of BC were evaluated, showing a progressive stiffening and increasing resistance with lower capacitance after partial dehydration. BC water loss was mathematically modelled for predicting its water content and for understanding the structural changes of post-dried BC. The dehydration of the samples was determined via water evaporation at 37 °C for different diameters and thicknesses. The gradual water evaporation observed was well-described by the model proposed (R² up to 0.99). The mathematical model for BC water loss may allow the optimisation of these properties for an intended application and may be extendable for other conditions and purposes.

Relationship between processing history and functionality recovery after rehydration of dried cellulose-based suspensions: A critical review

Cellulose-based suspensions have raised more and more attention due to their broad range of properties that can be used in paper industry and material science but also in medicine, nanotechnology and food science. Their final functionality is largely dependent on their processing history and notably the structural modifications that occur during drying and rehydration. The purpose of this work is to make a state-of-the-art contribution to the mechanisms involved in the process-structure-function relationships of cellulose-based hydrogels. The different assumptions that exist in the literature are reviewed taking the key role of the initial sample characteristics as well as the processing conditions into consideration. The decrease in swelling ability after drying is clearly due to an overall shrinkage of the structure of the material. At microscale, pore closure and cellulosic fibril aggregation are mentioned as the main reasons. The origins of such irreversible structural modifications take place at molecular level and is mainly explained by the establishment of a new balance of interactions between all components. Nevertheless, the respective contribution of each interaction are still under investigation.