Fabrication and characterization of nanofibrillated cellulose and its aerogels from natural pine needles

The emergence of nanocellulose aerogels in CO2 adsorption

Mitigating the effect of climate change toward a sustainable development is one of the main challenges of our century. The emission of greenhouse gases, especially carbon dioxide (CO2), is a leading cause of the global warming crisis. To address this issue, various sustainable strategies have been formulated for CO2 capture. Renewable nanocellulose aerogels have risen as a highly attractive candidate for CO2 capture thanks to their porous and surface-tunable nature. Nanocellulose offer distinctive characteristics, including significant aspect ratios, exceptional biodegradability, lightweight nature, and the ability for chemical modification due to the abundant presence of hydroxyl groups. In this review, recent research studies on nanocellulose-based aerogels designed for CO2 absorption have been highlighted. The state-of-the-art of nanocellulose-based aerogel has been thoroughly assessed, including their synthesis, drying methods, and characterization techniques. Additionally, discussions were held about the mechanisms of CO2 adsorption, the effects of the porous structure, surface functionalization, and experimental parameters. Ultimately, this synthesis review provides an overview of the achieved adsorption rates using nanocellulose-based aerogels and outlines potential improvements that could lead to optimal adsorption rates. Overall, this research holds significant promise for tackling the challenges of climate change and contributing to a more sustainable future.

Superhydrophobic, Magnetic Aerogels Based on Nanocellulose Fibers Derived from Harakeke for Oily Wastewater Remediation

Cellulose-based aerogels have been seen as a promising sorbent for oil and organic pollutant cleaning; however, their intrinsic hydrophilicity and difficulty of recycling has hindered their practical application. In this work, a superhydrophobic, magnetic cellulose-based aerogel was fabricated as a highly efficient sorbent for the adsorption of oils and organic solvents. The aerogel was prepared via a simple freeze-drying method, followed by chemical vapor deposition (CVD). The incorporation of Fe3O4 nanoparticles into the aerogel not only makes it responsive to external magnetic field, but also contributes to the better hydrophobicity of the aerogel, in which the water contact angle (WCA) was about 20° higher than the aerogel without loading with Fe3O4 nanoparticles. The adsorption test showed that the resultant aerogel can selectively adsorb a wide range of oils and organic solvents from oil/water mixtures with a high adsorption capacity (up to 113.49 g/g for silicone oil). It can retain about 50% of its adsorption capacity even after 10 adsorption-squeezing cycles, which indicates its outstanding reusability. Moreover, the aerogels can be easily controlled by an external magnet, which is preferred for the adsorption of oily contaminants in harsh environments and enhanced the recyclability of the aerogel. We believe that this study provides a green and convenient approach for the practical fabrication of cellulose-based oil sorbents.

Green solid-liquid extraction of cactus (Opuntia ficus-indica) cladode dietary fibers. I- optimization, pilot-scale production, and characterization

In this research work, an optimization of an environment friendly extraction method of cactus (Opuntia ficus indica) cladode dietary fibers was conducted. For this purpose, a central composite experimental design with two factors (temperature and time) and five levels was established. The basic objective of this optimization was to maximize fiber yield using hot water as an extraction eco-solvent. The optimum extraction time (330 min) and temperature (100 °C) were determined with a constant medium agitation rate. Additionally, this study also aimed at establishing the validation of the statistical model to carry out the extrapolation of the extraction process at the pilot scale. The fibers extracted at the pilot scale showed yields (45.2 ± 0.01%) in agreement with those obtained through the optimization and validation lab-scale steps (44.97 ± 0.02). Fourier Transform Infrared (FTIR) spectroscopy, X-ray Diffraction (XRD) and Scanning electron microscopy (SEM) analysis were conducted to investigate the structure and microstructure of pilot scale-produced fibers. FTIR spectrum and XRD pattern were typical to lignocellulosic fibers results. Sharp and thin peaks characteristic of cellulose were detected. Pure and crystallized phases were recorded with a 45% crystallinity index. SEM analysis presented elongated and organized cells with a uniform structure comparable to cellulosic fibers microstructure.

Nanocellulose: An amazing nanomaterial with diverse applications in food science

Recently, nanocellulose has gained growing interests in food science due to its many advantages including its broad resource of raw materials, renewability, interface stability, high surface area, mechanical strength, prebiotic characteristics, surface chemistry versatility and easy modification. Since then, this review summarized the sources, morphology, and structure characteristics of nanocellulose. Meanwhile, the mechanical, chemical, and combined treatment methods for the preparation of nanocellulose with desired properties were elaborated. Furthermore, the application of nanocellulose in Pickering emulsions, reinforced food packaging, functional food ingredient, food-grade hydrogels, and biosensors were emphasized. Finally, the safety, challenges, and future perspectives of nanocellulose were discussed. This work provided key developments and effective benefits of nanocellulose for future research opportunities in food.

Influence of the cellulose purification process on the properties of aerogels obtained from rice straw

Cellulose aerogels were obtained from purified rice straw cellulose fibres (CF) by applying different extraction methods: the conventional alkaline treatment (ALK) and alternative aqueous extraction based on the ultrasound combined with reflux heating (USHT) and subcritical water extraction (SWE) (160 and 180 °C). The composition and properties of the CFs were significantly affected by the purification process. The USHT treatment was as efficient as the ALK at eliminating the silica content, but the fibres maintained a notable ratio of hemicellulose (∼16 %). The SWE treatments were not so effective at removing silica (15 %) but greatly promoted the selective extraction of hemicellulose, especially at 180 °C (3 %). The CF compositional differences affected their hydrogel formation capacity and the properties of aerogels. A higher hemicellulose content in the CF led to better-structured hydrogels with better water-holding capacity, while the aerogels exhibited a more cohesive structure with thicker walls, higher porosity (99 %) and water vapour sorption capacity, but lower liquid water retention capacity (0.2 g/g). The residual silica content also interfered with the hydrogel and aerogel formation, giving rise to less structured hydrogels and more fibrous aerogels, with lower porosity (97-98 %).

Cellulosic pine needles-based biorefinery for a circular bioeconomy

Pine needles (PNs) are one of the largest bio-polymer produced worldwide. Its waste, i.e., fallen PNs, is mostly responsible for forest fires and is a major challenge. In present article, we have reviewed differenteffortsmadeto tackle this situation. PNs have been used in various fields such asin composite, water purification industries,electronic devices, etc. Gasification is one of the appealing processes for turning PNs into bio-energy; pyrolysis technique has been employed to create various carbon-based water purification materials; saccharification combined with fermentation produced good yields of bio-ethanol; Pd or Ni/PNs biocatalyst showed good catalytic properties in variousreactionsand pyrolysis with or without catalyst is an alluring technique to prepare bio-fuel. Nano cellulose extracted from PNs showed appealing thermal and mechanical strength. The air quality of nearbyenvironment was examinedby studying the magnetic properties of PNs. Packing materials made of PNs showed exceptional ethylene scavenging abilities.

Methylene blue removal using raw and modified biomass Plumeria alba (white frangipani) in batch mode: isotherm, kinetics, and thermodynamic studies

Hazardous dyes used in textile industries are considered high-risk pollutants to the environment. The raw as well as acid-treated Plumeria alba (white frangipani) leaf powder (WFLP and SWFLP) were used for the adsorption of methylene blue (MB) that is available in industrial wastewaters following the batch adsorption technique. The characterizations of adsorbents were done by FTIR, SEM, EDX, TGA, and zeta potential parameters. The adsorption was considered for the effects of temperature, initial dye concentration, solution pH, adsorbent dosage, and contact time. The experimental results obtained in the adsorption of MB were examined by nonlinear error functions like chi-square (χ²), ARE, and MPSD for three isotherm models: Langmuir, Freundlich, and Temkin. The maximum monolayer adsorption capacity, q_max (mg/g), was 45.45 mg/g for raw WFLP and 250 mg/g for SWFLP. The adsorbents fitted to the pseudo-second-order kinetic model (R² = 0.99) using the experimental data of batch adsorption. The thermodynamic studies explained the spontaneity and nature of adsorption for raw and acid-treated adsorbents. The batch experimental results and characterizations of the adsorbents revealed that the selected adsorbents would be the best adsorbents for the removal of MB from the wastewater solution.

Advanced cellulose nanocrystals (CNC) and cellulose nanofibrils (CNF) aerogels: Bottom-up assembly perspective for production of adsorbents

The most common and abundant polymer in nature is the linear polysaccharide cellulose, but processing it requires a new approach since cellulose degrades before melting and does not dissolve in ordinary organic solvents. Cellulose aerogels are exceptionally porous (>90 %), have a high specific surface area, and have low bulk density (0.0085 mg/cm³), making them suitable for a variety of sophisticated applications including but not limited to adsorbents. The production of materials with different qualities from the nanocellulose based aerogels is possible thanks to the ease with which other chemicals may be included into the structure of nanocellulose based aerogels; despite processing challenges, cellulose can nevertheless be formed into useful, value-added products using a variety of traditional and cutting-edge techniques. To improve the adsorption of these aerogels, rheology, 3-D printing, surface modification, employment of metal organic frameworks, freezing temperature, and freeze casting techniques were all investigated and included. In addition to exploring venues for creation of aerogels, their integration with CNC liquid crystal formation were also explored and examined to pursue "smart adsorbent aerogels". The objective of this endeavour is to provide a concise and in-depth evaluation of recent findings about the conception and understanding of nanocellulose aerogel employing a variety of technologies and examination of intricacies involved in enhancing adsorption properties of these aerogels.

Oil/water separation using elastic bio-aerogels derived from bagasse: Role of fabrication steps

Bio-aerogels hold great promise for selective oil separation from water due to their light weight and high sustainability. However, how the fabrication methods impact the elasticity and oil sorption performance of bio-aerogels still needs systematic comparison and in-depth investigation. In this study, the fabrication of hydrophobic bio-aerogels with good elasticity and reusability was optimized using a factorial design based on the dosages of bagasse-derived cellulose nanofiber, sodium alginate, and calcium carbonate. The role of each key fabrication step, including ice-templating, calcium crosslinking, solvent dehydration, freeze-drying, and silanization, played in the material properties was also elucidated. The optimized bio-aerogels had a low density (7.55 mg/cm³), high porosity (99.47%), large specific surface area (39 m²/g), and strong hydrophobicity (water contact angle of 135°). In addition, the bio-aerogels exhibited outstanding selective oil separation ability towards the oil-water mixture, with oil sorption capacity of 89-126 times its weight. The in-situ calcium crosslinking and solvent dehydration were vital to create porosity and preserve the microstructure of the bio-aerogels. The chemical vapor deposition rendered the bio-aerogels hydrophobic and oleophilic, greatly enhancing the separability of oil from the water-oil mixture.

Progress, Challenge and Perspective of Fabricating Cellulose

Cellulose as the most abundant biopolymers on Earth, presents appealing performance in mechanical properties, thermal management, and versatile functionalization. The development of fabrication methods closely relates to enrich its functionality and reduce manufacture cost. However, cellulose is hard to be dissolved by most common solvents or melt due to its recalcitrant property. Herein, the recent progress of fabricating cellulose is summarized. First, the unique hierarchical structure of cellulose is fully investigated and the resulted processability is highlighted in directions of down to nanocellulose, dissolution, and thermoplastic processing. Then, the reported fabrication methods are summarized in three aspects: (1) self-assembly from nano/micro cellulose suspensions, especially the self-assembly of cellulose nanocrystals; (2) dissolution-regeneration-drying, covering spinning and solvent infusion processing; and (3) thermoplastic processing, focusing on analysis of the setup and the morphology changes of the prepared products. In each aspect, the flowchart of the fabrication process, the behind mechanism, fabricated products, and effects of processing parameters are explored. Finally, this review provides a perspective on the further direction of fabricating cellulose, especially the challenges toward mass production of cellulose. This article is protected by copyright. All rights reserved.

Nanostructurally Controllable Strong Wood Aerogel toward Efficient Thermal Insulation

Eco-friendly materials with superior thermal insulation and mechanical properties are desirable for improved energy- and space-efficiency in buildings. Cellulose aerogels with structural anisotropy could fulfill these requirements, but complex processing and high energy demand are challenges for scaling up. Here we propose a scalable, nonadditive, top-down fabrication of strong anisotropic aerogels directly from wood with excellent, near isotropic thermal insulation functions. The aerogel was obtained through cell wall dissolution and controlled precipitation in lumen, using an ionic liquid (IL) mixture comprising DMSO and a guanidinium phosphorus-based IL [MTBD][MMP]. The wood aerogel shows a unique structure with lumen filled with nanofibrils network. In situ formation of a cellulosic nanofibril network in the lumen results in specific surface areas up to 280 m²/g and high yield strengths >1.2 MPa. The highly mesoporous structure (average pore diameter ∼20 nm) of freeze-dried wood aerogels leads to low thermal conductivities in both the radial (0.037 W/mK) and axial (0.057 W/mK) directions, showing great potential as scalable thermal insulators. This synthesis route is energy efficient with high nanostructural controllability. The unique nanostructure and rare combination of strength and thermal properties set the material apart from comparable bottom-up aerogels. This nonadditive synthesis approach is believed to contribute significantly toward large-scale design and structure control of biobased aerogels.

Bagasse Cellulose Composite Superabsorbent Material with Double-Crosslinking Network Using Chemical Modified Nano-CaCO3 Reinforcing Strategy

To improve the salt resistance of superabsorbent materials and the gel strength of superabsorbent materials after water absorption, a bagasse cellulose-based network structure composite superabsorbent (CAAMC) was prepared via graft copolymerization of acrylamide/acrylic acid (AM/AA) onto bagasse cellulose using silane coupling agent modified nano-CaCO₃ (MNC) and N,N′-methylene bisacrylamide (MBA) as a double crosslinker. The acrylamide/acrylic acid was chemically crosslinked with modified nano-CaCO₃ by C-N, and a stable double crosslinked (DC) network CAAMC was formed under the joint crosslinking of N,N′-methylene bisacrylamide and modified nano-CaCO₃. Modified nano-CaCO₃ plays a dual role of crosslinking agent and the filler, and the gel strength of composite superabsorbent is two times higher than that of N,N′-methylene bisacrylamide single crosslinking. The maximum absorbency of CAAMC reached 712 g/g for deionized water and 72 g/g for 0.9 wt% NaCl solution. The adsorption process of CAAMC was simulated by materials studio, and the maximum adsorption energy of amino and carboxyl groups for water molecules is −2.413 kJ/mol and −2.240 kJ/mol, respectively. According to the results of CAAMC soil water retention, a small amount of CAAMC can greatly improve the soil water retention effect.

Approaches for Extracting Nanofibrillated Cellulose from Oat Bran and Its Emulsion Capacity and Stability

The pretreatment process is an essential step for nanofibrillated cellulose production as it enhances size reduction efficiency, reduces production cost, and decreases energy consumption. In this study, nanofibrillated cellulose (NFC) was prepared using various pretreatment processes, either chemical (i.e., acid, basic, and bleach) or hydrothermal (i.e., microwave and autoclave), followed by disintegration using high pressure homogenization from oat bran fibers. The obtained NFC were used as an emulsifier to prepare 10% oil-in-water emulsions. The emulsion containing chemically pretreated NFC exhibited the smallest oil droplet diameter (d₃₂) at 3.76 μm, while those containing NFC using other pretreatments exhibited d₃₂ values > 5 μm. The colors of the emulsions were mainly influenced by oil droplet size rather than the color of the fiber itself. Both NFC suspensions and NFC emulsions showed a storage modulus (G′) higher than the loss modulus (G″) without crossing over, indicating gel-like behavior. For emulsion stability, microwave pretreatment effectively minimized gravitational separation, and the creaming indices of all NFC-emulsions were lower than 6% for the entire storage period. In conclusion, chemical pretreatment was an effective method for nanofiber extraction with good emulsion capacity. However, the microwave with bleaching pretreatment was an alternative method for extracting nanofibers and needs further study to improve the efficiency.

Polydopamine Induced Wettability Switching of Cellulose Nanofibers/n-Dodecanethiol Composite Aerogels

The novel wettability switchable cellulose nanofiber- (CNF-) based aerogel was conveniently prepared by polydopamine mediated composition of CNF and n-dodecanethiol. The wettability of aerogels can be controlled by adjusting the PDA and n-dodecanethiol loading content, which leads to a variation of water contact angle from 0-149°. The PDA was coated on cellulose nanofibers via hydrogen bonds and then n-dodecanethiol was anchored onto the scaffolds by Michael addition reaction, which was revealed by XPS and FTIR spectra. The composite aerogel can selectively absorb a series of oily liquids from the oil/water mixture, with the maximum absorption capacity of 68 g/g. This work presented a facile strategy to prepare wettability switchable CNF-based heterogenous aerogel and exhibited the potential of the composite aerogel for oil/water separation.

Application of biodegradable cellulose-based biomass materials in wastewater treatment

Water bodies contain a large number of harmful environmental pollutants, including oil, heavy metal ions and dyes, which has become a major global problem. The current work focusses on the development and future prospect of sustainable application of biodegradable cellulose-biomass materials in water treatment, considering that they show an important prospect in wastewater treatment. This paper summarizes the advantages and disadvantages of cellulose-biomass materials in removing harmful substances and pollutants from water and the key problems the technology faces. Cellulose-biomass material has unique structure, is environment friendly, degradable, renewable and provides low energy cost benefits, among other advantages. In this paper, the research progress of wastewater treatment in recent years is reviewed from the following three aspects: oil-water separation, heavy metal ions in water, and dye adsorption. The future research direction is also discussed.

Lignin and Xylan as Interface Engineering Additives for Improved Environmental Durability of Sustainable Cellulose Nanopapers

Cellulose materials and products are frequently affected by environmental factors such as light, temperature, and humidity. Simulated UV irradiation, heat, and moisture exposure were comprehensively used to characterize changes in cellulose nanopaper (NP) tensile properties. For the preparation of NP, high-purity cellulose from old, unused filter paper waste was used. Lignin and xylan were used as sustainable green interface engineering modifiers for NP due to their structural compatibility, low price, nontoxic nature, and abundance as a by-product of biomass processing, as well as their ability to protect cellulose fibers from UV irradiation. Nanofibrillated cellulose (NFC) suspension was obtained by microfluidizing cellulose suspension, and NP was produced by casting films from water suspensions. The use of filler from 1 to 30 wt% significantly altered NP properties. All nanopapers were tested for their sensitivity to water humidity, which reduced mechanical properties from 10 to 40% depending on the saturation level. Xylan addition showed a significant increase in the specific elastic modulus and specific strength by 1.4- and 2.8-fold, respectively. Xylan-containing NPs had remarkable resistance to UV irradiation, retaining 50 to 90% of their initial properties. Lignin-modified NPs resulted in a decreased mechanical performance due to the particle structure of the filler and the agglomeration process, but it was compensated by good property retention and enhanced elongation. The UV oxidation process of the NP interface was studied with UV-Vis and FTIR spectroscopy, which showed that the degradation of lignin and xylan preserves a cellulose fiber structure. Scanning electron microscopy images revealed the structural formation of the interface and supplemented understanding of UV aging impact on the surface and penetration depth in the cross-section. The ability to overcome premature aging in environmental factors can significantly benefit the wide adaption of NP in food packaging and functional applications.

Multifunctional 3D cationic starch/nanofibrillated cellulose/silver nanoparticles nanocomposite cryogel: Synthesis, adsorption, and antibacterial characteristics

We report a new 3D nanocomposite cryogel combines the advantages of cationic starch (Cs), nanofibrillated cellulose (NFC) and silver nanoparticles (Ag NPs). Cs was the main component of the cryogel while NFC was used as a filling agent to enhance the mechanical properties of the produced cryogel. Both Cs and NFC endow the cryogel with adsorption properties while Ag NPs enhances its antibacterial properties. Ag NPs was green synthesized with the aid of microwave radiation using NFC as reducing and stabilizing agent. The prepared Ag particles were free of impurities with sizes <10 nm and good stability in solution. Two different concentrations of the prepared Ag NPs were added to a mixture of Cs and NFC and subjected to freeze drying to get porous cryogel (3D microstructure). The Ag NPs free cryogel has highly porosity smooth surface with large surface area. Adding Ag NPs decreased these features and increased the 3D roughness. Optimum adsorption of reactive blue 49 was observed after 30 min of contact with 1.5 g/L of the cryogel at pH 1. The adsorption kinetics and isotherm were best described by the pseudo-first-order and Freundlich equations, respectively. All prepared cryogels have notable antibacterial properties that were significantly improved by adding Ag NPs. Overall, the new 3D composite cryogel can efficiently remove dyes and bacteria from wastewater.

Current Status of Cellulosic and Nanocellulosic Materials for Oil Spill Cleanup

Recent developments in the application of lignocellulosic materials for oil spill removal are discussed in this review article. The types of lignocellulosic substrate material and their different chemical and physical modification strategies and basic preparation techniques are presented. The morphological features and the related separation mechanisms of the materials are summarized. The material types were classified into 3D-materials such as hydrophobic and oleophobic sponges and aerogels, or 2D-materials such as membranes, fabrics, films, and meshes. It was found that, particularly for 3D-materials, there is a clear correlation between the material properties, mainly porosity and density, and their absorption performance. Furthermore, it was shown that nanocellulosic precursors are not exclusively suitable to achieve competitive porosity and therefore absorption performance, but also bulk cellulose materials. This finding could lead to developments in cost- and energy-efficient production processes of future lignocellulosic oil spillage removal materials.

Self-Assembled Behavior of Ultralightweight Aerogel from a Mixture of CNC/CNF from Oil Palm Empty Fruit Bunches

This study aims to explore the use of cellulose nanocrystals (CNC) and cellulose nanofiber (CNF), obtained from unbleached fiber of oil palm empty fruit bunches (EFB), as raw materials in fabricating aerogel, using the facile technique without solvent displacement. The CNC was isolated from sulfuric acid hydrolysis, and the CNF was fibrillated using Ultra Turrax. The CNC and CNF were mixed by ultrasonication in different ratios to produce aerogel using slow freezing (−20 °C), followed by freeze-drying. The obtained aerogel was characterized as ultralightweight and highly porous material, at the density range of 0.0227 to 0.0364 g/cm³ and porosity of 98.027 to 98.667%. Interestingly, the ratio of CNC and CNF significantly affected the characteristics of the obtained aerogel. The mixed aerogel exhibited a higher specific surface area than pure CNC or CNF, with the highest value of 202.72 m²/g for the ratio of 1:3 (CNC/CNF). In addition, the crystallinity degree of obtained aerogel showed a higher value in the range of 76.49 to 69.02%, with the highest value being obtained for higher CNC content. This study is expected to provide insight into nanocellulose-based aerogel, with a promising potential for various applications.

Lignocellulose aerogel and amorphous silica nanoparticles from rice husks

Abstract

Rice Husks (RHs) are one of the most abundant sources of biomass in the world due to rice consumption. Lignocellulose and silica are two of the main components of RHs, which allow RHs to be applied in different areas. Lignocellulose can be partially dissolved in 1-butyl-3-methylimidazolium chloride (BMIMCl), which is a simple way of competing with the traditional extraction methods that suffer from high chemical consumption. A lignocellulose freeze gel is obtained via a cyclic liquid nitrogen freeze-thaw (NFT) process. Multi-functional self-assembled lignocellulose aerogel is obtained after CO2 supercritical drying. Based on the aerogel’s special properties, two routes are developed for practical applications. On one hand, the aerogel is coated to exhibit a superhydrophobic property that can be applied as an absorbent for oil spills. On the other hand, a carbon aerogel is synthesized via a pyrolysis process, resulting in a porous amorphous carbon. The residue after partially dissolving lignocellulose in BMIMCl is further calcined to obtain amorphous silica nanoparticles, achieving a comprehensive application of RHs.

Graphical abstract

Nanocellulose from various biomass wastes: Its preparation and potential usages towards the high value-added products

Biomass waste comes from a wide range of sources, such as forest, agricultural, algae wastes, as well as other relevant industrial by-products. It is an important alternative energy source as well as a unique source for various bioproducts applied in many fields. For the past two decades, how to reuse, recycle and best recover various biomass wastes for high value-added bioproducts has received significant attention, which has not only come from various academia communities but also from many civil and medical industries. To summarize one of the cutting-edge technologies applied with nanocellulose biomaterials, this review focused on various preparation methods and strategies to make nanocellulose from diverse biomass wastes and their potential applications in biomedical areas and other promising new fields.

Top-Down Approach Making Anisotropic Cellulose Aerogels as Universal Substrates for Multifunctionalization

Highly porous, strong aerogels with anisotropic structural properties are of great interest for multifunctional materials for applications including insulators in buildings, filters for oil cleanup, electrical storage devices, etc. Contemporary aerogels are mostly extracted from fossil resources and synthesized from bottom-up techniques, often requiring additional strategies to obtain high anisotropy. In this work, a universal approach to prepare porous, strong, anisotropic aerogels is presented through exploiting the natural hierarchical and anisotropic structure of wood. The preparation comprises nanoscale removal of lignin, followed by dissolution-regeneration of nanofibers, leading to enhanced cell wall porosity with nanofibrillated networks occupying the pore space in the cellular wood structure. The aerogels retain structural anisotropy of natural wood, exhibit specific surface areas up to 247 m²/g, and show high compression strength at 95% porosity. This is a record specific area value for wood aerogels/foams and even higher than most cellulose-based aerogels for its assigned strength. The aerogel can serve as a platform for multifunctional composites including scaffolds for catalysis, gas separation, or liquid purification due to its porous matrix or as binder-free electrodes in electronics. To demonstrate the multifunctionality, the aerogels are successfully decorated with metal nanoparticles (Ag) and metal oxide nanoparticles (TiO₂) by in situ synthesis, coated by the conductive polymer (PEDOT:PSS), and carbonized to yield conductive aerogels. This approach is found to be a universal way to prepare highly porous anisotropic aerogels.

LIGHTWEIGHT ELASTOMER COMPOUNDS REINFORCED WITH CELLULOSE NANOFIBRILS AND A CARBON BLACK HYBRID FILLER SYSTEM

Cellulose is found in the walls of plant cells, making it the most common biopolymer in the world. It is mechanically stable, resistant to hydrolysis, and boasts—especially in its nanoscopic state—a large reactive surface area and low density. To realize reinforcement in rubbers, the large and polar cellulose surface must interact with the nonpolar elastomer matrix. The dispersion of hydrophilic fillers is, however, still a major challenge in rubber technology. In this work, commercially available nanofibrillated cellulose (NFC) was incorporated into a nonpolar BIIR via latex mixing. Transmission electron microscopy, tensile testing, swelling, and rheometry were used to characterize the compound properties and the reinforcing potential of NFC. The compounds were compared with the established and highly dispersible standard carbon black N550 with a medium specific surface area. In addition, hybrid filler systems with both particle types were prepared. This yielded well-dispersed nanocomposites of a new kind exhibiting high stiffness, good tensile properties, and reduced material weight.

Highly absorbent cellulose nanofibrils aerogels prepared by supercritical drying

In this paper, strictly speaking aerogels of cellulose nanofibrils (CNFs) and TEMPO-oxidized CNFs (TO-CNFs) were obtained from an optimized supercritical drying processes and cryogels were prepared after freeze-drying. The cryogels and aerogels were characterized and the influence of the preparation process on the resulting properties was studied. Significant differences were observed in the micro- and nanoscale organization of the porous structures. In addition, the specific surface areas measured varied from 25 to 160 m² g^-1 for CNF materials, depending on the preparation process. Very high specific surface areas up to 482 m² g^-1 among the highest reported for pure cellulose nanofibrils porous materials were achieved for TO-CNF aerogels. Finally, in order to evaluate their aptitudes for wound dressings applications, the capillary water uptake capacities were assessed on skin mimicking layers. From this study, it was revealed that TO-CNF aerogels can absorb almost 120 times their own weight of water.

Esterified superhydrophobic nanofibrillated cellulose based aerogel for oil spill treatment

The present work aims towards the structuring of a physically cross-linked aerogels based on nanofibrillated cellulose (NFC) and polyvinyl alcohol (PVA), i.e., NFC/PVA aerogels for oil spillage cleanup. Highly porous (98%) NFC/PVA aerogels having both meso-micro pores were achieved by freeze drying technique. To impart super-hydrophobicity to the composite aerogel, a simple dip coating process was adopted using stearic acid chloride (SAC) solution. The SAC conjugated aerogels combined both superhydrophobic and oleophilic characteristics showed a contact angle of ∼159° and ∼0° with water and oil respectively. FESEM and X-ray microtomography images revealed a self-assembled 3D porous cellular structure of the aerogels. The prepared aerogels were found to be very efficient in separating a series of oil/water mixtures and various organic solvents with excellent selectivity and recyclability. Absorption capacity of the aerogels was at least 35 times higher than their dry weight. Simple mechanical squeezing method was adopted for repetitive uses.

Preparation of Nanocellulose Aerogel from the Poplar (Populus tomentosa) Catkin Fiber

: The effects of chemical pretreatment on the purification of poplar (Populus tomentosa) catkin fiber and the effect of ultrasonic time for the microfibrillarization of poplar catkin fiber (PCF) were studied. The nanocellulose aerogels were prepared by freeze drying the cellulose solutions. The density, porosity, micro morphology, thermal stability and mechanical properties of the aerogels were analyzed. It was found that the dewaxing time of PCF is shorter than that of unsonicated nanocellulose. After the treatment of 0.5 wt% sodium chlorite for 2 h, the lignin of PCF was removed. After the chemical purification, the PCF was treated with 2 and 5 wt% NaOH solution and ultrasonicated for 5 and 10 min, respectively. When the ultrasonic time was 10 min, the diameter of the nanocellulose was 20-25 nm. When the ultrasonic time was 5 min, the aerogels with porous honeycomb structure can be prepared by using the nanocellulose sol of PCF as raw material. The density of the aerogels was only 0.3-0.4 mg/cm3 and the porosities of the aerogels were all larger than 99%. The difference between the pyrolysis temperature of aerogels was small, the elastic modulus of aerogels was 30–52 kPa, and the compressive strength was 22–27 kPa. With the increase of the concentration of NaOH solution (5 wt%) and ultrasonic time (10 min), the elastic modulus of aerogels increased gradually and reached the maximum value of 52 kPa, while the compressive strength reached the maximum value of 27 kPa when the PCF being treated in 5 wt% NaOH solution and was ultrasonicated for 5 min.

Cadmium adsorption characteristics of biochars derived using various pine tree residues and pyrolysis temperatures

This study investigated the characteristics of biochars derived using various pine tree residues and pyrolysis temperatures and evaluated their Cd adsorption behaviors. The characteristics of pine tree residue biochars (PRBs) were dominantly affected by the pyrolysis temperature, and the optimum pyrolysis temperature for Cd adsorption was 600 °C. The adsorption of Cd by PRBs was divided into two stages: rapid adsorption on the initial boundary layer and slow adsorption by intraparticle diffusion. The Cd adsorption characteristics of all the PRBs were well described by pseudo-second-order and Langmuir isotherm models, and the maximum adsorption capacity was the highest in pine bark biochar (85.8 mg/g). The amounts of the cations released from the mixed pine tree residue biochars (M-PRBs) during Cd adsorption were increased, while the amount of phosphate released was decreased, indicating that exchangeable cations and phosphate on the biochar affected the Cd adsorption. In particular, the amount of Cd removed by the exchangeable cations corresponds to 23.6% of the total adsorption amount. Spectroscopic analyses using FTIR showed that the Cd adsorption on M-PRB was associated with functional groups such as CC, COH and COOH. Overall, the use of biochars derived from pine tree residue as an adsorbent is considered to be effective for both the treatment of wastewater containing heavy metals and the recycling of forest residues.

Controllable synthesis of pomelo peel-based aerogel and its application in adsorption of oil/organic pollutants

Oil/water separation is a field of high significance as it might efficiently resolve the contamination of industrial oily wastewater and other oil/water pollution. In this paper, an environmentally-friendly hydrophobic aerogel with high porosity and low density was successfully synthesized with renewable pomelo peels (PPs) as precursors. Typically, a series of sponge aerogels (HPSA-0, HPSA-1 and HPSA-2) were facilely prepared via high-speed dispersion, freeze-drying and silanization with methyltrimethoxysilane. Indeed, the physical properties of aerogel such as density and pore diameter could be tailored by different additives (filter paper fibre and polyvinyl alcohol). Hence, their physico-chemical properties including internal morphology and chemical structure were characterized in detail by Fourier transform infrared, Brunauer-Emmett-Teller, X-ray diffraction, scanning electron microscope, Thermal gravimetric analyzer (TG) etc. Moreover, the adsorption capacity was further determined and the results revealed that the PP-based aerogels presented excellent adsorption performance for a wide range of oil products and/or organic solvents (crude oil 49.8 g g^-1, soya bean oil 62.3 g g^-1, chloroform 71.3 g g^-1 etc.). The corresponding cyclic tests showed the absorption capacity decreased slightly from 94.66% to 93.82% after 10 consecutive cycles, indicating a high recyclability.

Cellulose Aerogels: Synthesis, Applications, and Prospects

Due to its excellent performance, aerogel is considered to be an especially promising new material. Cellulose is a renewable and biodegradable natural polymer. Aerogel prepared using cellulose has the renewability, biocompatibility, and biodegradability of cellulose, while also having other advantages, such as low density, high porosity, and a large specific surface area. Thus, it can be applied for many purposes in the areas of adsorption and oil/water separation, thermal insulation, and biomedical applications, as well as many other fields. There are three types of cellulose aerogels: natural cellulose aerogels (nanocellulose aerogels and bacterial cellulose aerogels), regenerated cellulose aerogels, and aerogels made from cellulose derivatives. In this paper, more than 200 articles were reviewed to summarize the properties of these three types of cellulose aerogels, as well as the technologies used in their preparation, such as the sol⁻gel process and gel drying. In addition, the applications of different types of cellulose aerogels were also introduced.

Synthesis and Characterization of Cellulose Nanofibril-Reinforced Polyurethane Foam

In this study, traditional polyol was partially replaced with green, environmentally friendly cellulose nanofibrils (CNF). The effects of CNF on the performance of CNF-reinforced polyurethane foam nanocomposites were investigated using scanning electron microscopy, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) analysis, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and a compression test. The results showed that the introduction of CNF into the polyurethane matrix not only created stronger urethane bonding between the hydroxyl groups in the cellulose chain and isocyanate groups in polymethylene polyphenylisocyanate, but also developed an additional filler⁻matrix interaction between CNF and polyurethane. With the increase of the CNF replacement ratio, a higher glass transition temperature was obtained, and a higher amount of char residue was generated. In addition, an increase of up to 18-fold in compressive strength was achieved for CNF-PUF (polyurethane foam) nanocomposites with a 40% CNF replacement ratio. CNF has proved to be a promising substitute for traditional polyols in the preparation of polyurethane foams. This study provides an interesting method to synthesize highly green bio-oriented polyurethane foams.

Facile Fabrication of Nanofibrillated Chitin/Ag2O Heterostructured Aerogels with High Iodine Capture Efficiency

Nanofibrillated chitin/Ag₂O aerogels were fabricated for radioiodine removal. Chitin was first fabricated into nanofibers with abundant acetyl amino groups (–NHCOCH₃) on the surface. Then, highly porous chitin nanofiber (ChNF) aerogels were obtained via freeze-drying. The ChNF aerogels exhibited a low bulk density of 2.19 mg/cm³ and a high specific surface area of 179.71 m²/g. Ag₂O nanoparticles were evenly anchored on the surfaces of ChNF scaffolds via strong interactions with –NHCOCH₃ groups, subsequently yielding Ag₂O@ChNF heterostructured aerogels. The composites were used as efficient absorbents to remove radioiodine anions from water and capture a high amount of I₂ vapor in the forms of AgI and iodine molecules. The adsorption capacity of the composite monoliths can reach up to 2.81 mmol/g of I⁻ anions. The high adsorbability of the composite monolithic aerogel signifies its potential applications in radioactive waste disposal.

Resource recovery of Eichhornia crassipes as oil superabsorbent

The elastic cellulose-based aerogels (CBAs) with highly porous (99.56%) and low-density (0.0065gcm^-1) were prepared using Eichhornia crassipes as cellulose source and polyvinyl alcohol directly as cross-linker via a facile and environment-friendly process. The prepared CBAs exhibited excellent oil/solvent sorption capacities (60.33-152.21gg^-1), super-hydrophobicity (water contact angle of 156.7°) as well as remarkable reusability. More importantly, the absorbed oil could be quickly recovered by simple squeezing without significantly structure damage (at least 16 times). All these merits make CBAs very promising materials for oil spillage cleaning.

Cellulose Nanocrystals (CNCs) from Corn Stalk: Activation Energy Analysis

Cellulose nanocrystals (CNCs) were isolated from corn stalk using sulfuric acid hydrolysis, and their morphology, chemical structure, and thermal stability properties were characterized. The CNCs had an average length of 120.2 ± 61.3 nm and diameter of 6.4 ± 3.1 nm (L/D = 18.7). The degree of crystallinity of the CNCs increased to 69.20% from the 33.20% crystallinity of raw corn stalk fiber, while the chemical structure was well kept after sulfuric acid hydrolysis. Thermal stability analysis showed that the degradation temperature of the CNCs reached 239.5 °C, which was higher than that of the raw fiber but lower than that of the extracted cellulose. The average activation energy values for the CNCs, evaluated using the Friedman, Flynn-Wall-Ozawa (F-W-O) and Coats-Redfern methods, were 312.6, 302.8, and 309 kJ·mol^-1 in the conversion range of 0.1 to 0.8. The isolated CNCs had higher values of activation energy than did the purified cellulose, which was attributed to the stronger hydrogen bonds present in the crystalline domains of CNCs than in those of cellulose. These findings can help better understand the thermal properties of polymer/CNC composites.

Preparation and Characterization of Nanofibrillated Cellulose from Bamboo Fiber via Ultrasonication Assisted by Repulsive Effect

Nanofibrillated celluloses (NFCs) have recently drawn much attention because of their exceptional physicochemical properties. However, the existing preparation procedures either produce low yields or severely degrade the cellulose and, moreover, are not energy efficient. The purpose of this study was to develop a novel process using ultrasonic homogenization to isolate fibrils from bamboo fiber (BF) with the assistance of negatively charged entities. The obtained samples were characterized by the degree of substitution (DS) of carboxymethyl, Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis, and transmission electron microscopy (TEM). The results showed that an NFC yield could be obtained above 70% through this route. The enzyme hydrolysis could enhance the surface charge of the fiber, and mechanical activation facilitates an increase in the DS. The disintegrating efficiency of the cellulose fibrils significantly depended on the input power of ultrasonication and the DS. FT-IR spectra confirmed the occurrence of the carboxymethylation reaction based on the appearance of the characteristic signal for the carboxyl group. From XRD analysis, it was observed that the presence of the carboxyl groups makes the isolation more efficient attributed to the ionic repulsion between the carboxylate groups of the cellulose chains.