Thermal stability of polyvinyl alcohol/nanocrystalline cellulose composites

Large-scale dual-responsive ClO2 controlled-release film for strawberry preservation

Chlorine dioxide (ClO2) exhibits promising potential for the application in food preservation. However, the large-scale production of controlled-release ClO2 films faces challenges. The sodium chlorite microcapsules (Micro-SC) were successfully prepared in this study using polyvinyl alcohol (PVA) as the wall material through the spray drying method. Furthermore, A large-scale preparation of temperature and humidity dual-responsive ClO2 controlled-release films (Micro-SC@EVA) was achieved using melt extrusion. The film could release ClO2 triggered by water vapor for 36 days. The antibacterial effects were significantly enhanced with the increase of microcapsule ratio from 4 % to 8 %. The Micro-SC@EVA film reduced the total viable count and wight loss of strawberries, inhibits ethylene production, and extended the shelf life of by 150 % compared with the control group at 25 °C. The application evaluation results show that the novel approach for the large-scale preparation of ClO2 controlled-release film holds significant implications for food packaging.

Sprayable oxidized polyvinyl alcohol with improved degradability and sufficient mechanical property for fruit preservation

Besides their limited preservation capacity and low biosafety, traditional fruit preservation procedures exacerbate "white pollution" because they utilize excessive plastic. Herein, an environmentally friendly one-pot method was developed to obtain degradable polyvinyl alcohol (PVA), where the hydroxyl radicals generated through the reaction between hydrogen peroxide (H2O2) and iron ions functioned to oxidize PVA. The oxidized PVA (OPVA-1.0) with abundant ketone groups, reduced crystallinity, and short molecular chains was completely degraded into H2O and CO2 after being buried in the soil for ∼60 days. An improvement in its degradation rate did not weaken the mechanical properties of OPVA-1.0 compared to other modified PVA films because the adverse effect of decreased crystallinity on its mechanical performance was offset by its ion coordination. Alternatively, the tensile strength or toughness of OPVA-1.0 was enhanced due to its internal multi-level interactions including molecular chain entanglement, hydrogen bonding, and metal coordination bonds. More interestingly, OPVA-1.0 was water-welded into various products in a recyclable way owing to its reversible physical bonds, where it was sprayed, dipped, or brushed conformally onto different perishable fruits to delay their ripening by 5-14 days. Based on the cellular biocompatibility and biosafety evaluations in mice, OPVA-1.0 obtained by the facile oxidation strategy was demonstrated to alleviate "white pollution" and delay the ripening of fruits effectively.

Designing for Degradation: Transient Devices Enabled by (Nano)Cellulose

Transient technology involves materials and devices that undergo controlled degradation after a reliable operation period. This groundbreaking strategy offers significant advantages over conventional devices based on non-renewable materials by limiting environmental exposure to potentially hazardous components after disposal, and by increasing material circularity. As the most abundant naturally occurring polymer on Earth, cellulose is an attractive material for this purpose. Besides, (nano)celluloses are inherently biodegradable and have competitive mechanical, optical, thermal, and ionic conductivity properties that can be exploited to develop sustainable devices and avoid the end-of-life issues associated with conventional systems. Despite its potential, few efforts have been made to review current advances in cellulose-based transient technology. Therefore, this review catalogs the state-of-the-art developments in transient devices enabled by cellulosic materials. To provide a wide perspective, the various degradation mechanisms involved in cellulosic transient devices are introduced. The advanced capabilities of transient cellulosic systems in sensing, photonics, energy storage, electronics, and biomedicine are also highlighted. Current bottlenecks toward successful implementation are discussed, with material circularity and environmental impact metrics at the center. It is believed that this review will serve as a valuable resource for the proliferation of cellulose-based transient technology and its implementation into fully integrated, circular, and environmentally sustainable devices.

Ratiometric fluorescent test strips based on CB-Ni2+@CDs probes for visual detection of histamine

Histamine is a biogenic amine with various physiological functions. However, excessive consumption of histamine can lead to various symptoms, and pose a threat to human lives. A ratiometric fluorescent test strip for visual detection of histamine was developed based on CB-Ni2+@CDs probes. As the concentration of histamine increases, the test strips exhibit a transition in fluorescence signal from yellow-green to blue. The RGB values were extracted from the images, and used for quantitative analysis of histamine. The method had a linear range of 0-1.0 mM, with a detection limit of 0.086 mM. The test strips were employed for the detection of histamine, and the recovery rate was found to be in the range of 88.3% to 104.69%, indicating a high level of accuracy. The uniqueness of the test strips lies in their ability to be produced simply by mixing CB, Ni2+ on a suitable polyvinyl alcohol/wood cellulose fiber substrate.

Physicochemical Properties of Cellulose Nanocrystals Extracted from Postconsumer Polyester/Cotton-Blended Fabrics and Their Effects on PVA Composite Films

The utilisation of cotton waste as precursors in the synthesis of nanocrystalline cellulose has gained significant attention. This approach suggests a sustainable solution to address the growing concern of textile waste accumulation while simultaneously producing a valuable material. The main aim of this study is to examine the properties of cellulose nanocrystals (CNCs) obtained from postconsumer polyester-cotton waste and assess the effect of different fabric structures on the extraction and these properties. To acquire nanocellulose, a thorough decolourisation pretreatment process was utilised, which involved the treatment of polyester-cotton waste with sodium dithionite and hydrogen peroxide. Consequently, the postconsumer material was then treated with an acid hydrolysis method employing a 64% (v/v) sulphuric acid solution at 50 °C for 75 min, resulting in the formation of CNCs with average yield percentages ranging from 38.1% to 69.9%. Separation of the acid from the CNC was facilitated by a centrifugation process followed by dialysis against deionised water. Uniform dispersion was then achieved using ultrasonication. A variety of analytical techniques were employed to investigate the morphological, chemical, thermal, and physical properties of the isolated CNCs. Among these techniques, attenuated total reflection-Fourier-transform infrared spectroscopy (ATR-FTIR), energy-filtered transmission electron microscopy (EF-TEM), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) were utilised to analyse the CNCs. The findings indicated that the separated CNCs exhibited a rod-shaped morphology, measuring between 78 and 358 nm in length and 5 and 16 nm in diameter, and also exhibited high crystallinity (75-89%) and good thermal stability. The extracted CNCs were mixed with polyvinyl alcohol (PVA) and glycerol to assess their reinforcing effect on plastic films. The prepared composite film exhibited improved mechanical properties and thermal stability. Incorporating CNCs led to a 31.9% increase in the tensile strength and a 42.33% rise in the modulus of elasticity. The results from this research proved that CNCs can be extracted from postconsumer mixed fabrics as a potential solution to effectively address the mounting concerns surrounding waste management in the textile industry and also provide avenues for enhancing the qualities of eco-friendly composite films.

Polyvinyl alcohol/kappa-carrageenan-based package film with simultaneous incorporation of ferric ion and polyphenols from Capsicum annuum leaves for fruit shelf-life extension

Bio-based food packaging materials have elicited growing interests due to their great degradability, high safety and active biofunctions. In this work, by simultaneously introducing the polyphenolic extracts from Capsicum annuum leaves and ferric ion (Fe3+) into the Polyvinyl alcohol/kappa-carrageenan (PVA/κ-carrageenan)-based film-forming matrix, an active package film was developed, with the purpose to improve the food shelf life. The experimental results indicated that the existence of Fe3+ can not only improve the mechanical properties owing to the multiple dynamic coordinated interactions, but also endow the composite films with excellent fire-retardancy. Moreover, the composite films could display excellent UV resistant performance, water vapor/oxygen gas barrier properties and antioxidant activities with the corporation of polyphenols. In particular, the highest DPPH and ABTS radical scavenging capacities for composite film (PC-PLP7 sample) were evaluated to be 82.5 % and 91.1 %, respectively. Higher polyphenol concentration is favorable to the bio-functions of the materials. Benefitting from these features, this novel kind of films with a dense and steady micro-structure could be further applicated in fruit preservations, where the ripening bananas were ensured with the high storage quality. This integration as a prospective food packaging material provides an economic and eco-friendly approach to excavate the high added-values of biomass.

Synthesis, characterization, and cytotoxicity studies of nanocellulose extracted from okra (Abelmoschus Esculentus) fiber

Nanocellulose, especially originating from a natural source, has already shown immense potential to be considered in various fields, namely packaging, papermaking, composites, biomedical engineering, flame retardant, and thermal insulating materials, etc. due to its environmental friendliness and novel functionalities. Thus, a thorough characterization of nanocellulose is a hot research topic of research communities in a view to judge its suitability to be used in a specific area. In this work, a kind of green and environment-friendly nanocellulose was successfully prepared from okra fiber through a series of multi-step chemical treatments, specifically, scouring, alkali treatment, sodium chlorite bleaching, and sulfuric acid hydrolysis. Several characterization techniques were adopted to understand the morphology, structure, thermal behavior, crystallinity, and toxicological effects of prepared nanocellulose. Obtained data revealed the formation of rod-shaped nanocellulose and compared to raw okra fiber, their size distributions were significantly smaller. X-ray diffraction (XRD) patterns displayed that compared to the crystalline region, the amorphous region in raw fiber is notably larger, and in obtained nanocellulose, the crystallinity index increased significantly. Moreover, variations in the Fourier transform infrared spectroscopy (FTIR) peaks depicted the successful removal of amorphous regions, namely, lignin and hemicelluloses from the surface of fiber. Thermostability of synthesized nanocellulose was confirmed by both Differential Scanning Calorimetry (DSC) analysis, and thermogravimetric analysis (TGA). Cytotoxicity assessment showed that the okra fiber-derived nanocellulose exhibited lower to moderate cellular toxicity in a dose-dependent manner where the LD50 value was 60.60 μg/ml.

Tunable biocomposite films fabricated using cellulose nanocrystals and additives for food packaging

Cellulose nanocrystals (CNCs) are considered a prospective packaging material to partially replace petroleum-based plastics attributed to their renewability, sustainability, biodegradability, and desirable attributes including transparency, oxygen, and oil barrier properties. However, neat CNC films are rigid and too brittle to handle or utilize for packaging applications. Hence different additives, including sorbitol, polyvinyl alcohol (PVA), chitin, and κ-carrageenan (CG) were selected to mix with CNCs for packaging film preparation. The influence of additive categories (plasticizer, nonionic polymer, weak cationic and anionic natural polysaccharide), and their concentrations on the performance of CNC suspensions as well as optical, barrier, mechanical, and thermal properties of CNC films were examined. The morphology and physical characterization including density, equilibrium moisture content, contact angle and water durability of the composite films were also determined. Sorbitol and PVA films had the best visible light transparency; mixing with chitin can effectively improve the water durability of CNC films, and CG changed the CNC film from hydrophilic to hydrophobic. Moreover, all CNC films exhibited sufficient oxygen barrier properties, high PVA content films attained the "very high" barrier grade. Thus, durable CNC films can be obtained by adding proper types and amounts of additives, which provides potential scenarios for practical application of CNC films in food packaging.

Reuse of used paper egg carton boxes as a source to produce hybrid AgNPs- carboxyl nanocellulose through bio-synthesis and its application in active food packaging

The proper disposal of disposable synthetic plastic food packaging materials presents a significant challenge for both the environment and the solid waste management community. To address this issue, an antibacterial-based high-strength bio-composite serves as the optimal alternative to conventional packaging materials. This study aims to produce a hybrid material of AgNPs-carboxyl cellulose nanocrystals (AgNPs-CCNCs), obtained from used egg carton boxes (UECBs), through bio acid hydrolysis and an in-situ generation process. Furthermore, AgNPs- carboxyl cellulose nanofibers (AgNPs-CCNFs) will be synthesized through a combination of bio acid hydrolysis and ball milling, followed by an additional in-situ generation step. The AgNPs-carboxyl nanocellulose (AgNPs-CCNCs, and AgNPs-CCNFs) exhibited excellent crystallinity index, morphology, thermal, and antibacterial properties. The morphological analysis was performed by electron microscopy, and the results showed the uniform distribution and spherical form of AgNPs appearing over the carboxyl nanocellulose through the in-situ generation process, which was confirmed through XRD analysis. The study further explores the impact of AgNPs-carboxyl nanocellulose on the mechanical, chemical, antibacterial, and thermal properties of the PVA matrix. The results demonstrate that the bio-nanocomposite film offers opportunities for utilization in active packaging applications.

Enhancing the Mechanical Properties of Poly(vinyl alcohol) Fibers by Lithium Iodide Addition

The effect of lithium iodide (LiI) on the mechanical strength, properties, and molecular orientation of poly(vinyl alcohol) (PVA) fibers spun by wet spinning and then heat-stretched was studied. The stretchability of LiI-PVA fibers was improved, and the rupture during stretching was suppressed compared to PVA fibers. In addition, the tensile strength and elastic modulus of the thermally stretched fibers have been significantly improved. It was also found that the addition of LiI improves the molecular orientation of PVA. This was achieved because LiI reduced the hydrogen bonds between the molecular chains of PVA, resulting in reduced crystallinity. Most of the LiI in the fiber could be removed by a coagulation bath and washing during the spinning process. This means that LiI is eventually removed, and the heat-treatment strengthens the hydrogen bonds, resulting in excellent mechanical strength.

Preparation of Nanocellulose from Coffee Pulp and Its Potential as a Polymer Reinforcement

Coffee is one of the most valued agricultural products regarding its high commercialization rate. During the production of coffee beans, coffee pulp is obtained as one of the main byproducts with a cellulose content of more than 30% of dry weight. This research focused on the value-added potential of coffee pulp fiber as the reinforcement in composite materials. The nanocellulose coffee pulp (NCP) from the coffee pulp (CP) was prepared and subsequently used as a filler to reinforce the polyvinyl alcohol (PVA) matrix for the improvement of PVA composite properties. The CP was treated via alkali and bleaching treatment before the production of NCP using the acid hydrolysis treatment. The TEM result of NCP showed the successful preparation of NCP with an average diameter of 16.03 ± 4.70 nm with increasing crystallinity size and crystallinity index. The effect of glycerol (G) in the PVA matrix was observed. The result showed that glycerol had a play-role as a plasticizer for increased flexibility and decreased hardness and brittleness of PVA nanocomposite film. The nanocomposite film of PVA/G/NCP was fabricated with various ratios of NCP through the casting method. It was shown that the physical properties were improved with the presence of NCP in the PVA matrix compared to the neat PVA film.

Engineered Highly Porous Polyvinyl Alcohol Hydrogels with Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and Graphene Nanosheets for Musculoskeletal Tissue Engineering: Morphology, Water Sorption, Thermal, Mechanical, Electrical Properties, and Biocompatibility

Electroactive composite materials are very promising for musculoskeletal tissue engineering because they can be applied in combination with electrostimulation. In this context, novel graphene-based poly(3-hydroxybutyrate-co-3-hydroxyvalerate)/polyvinyl alcohol (PHBV/PVA) semi-interpenetrated networks (semi-IPN) hydrogels were engineered with low amounts of graphene (G) nanosheets dispersed within the polymer matrix to endow them with electroactive properties. The nanohybrid hydrogels, obtained by applying a hybrid solvent casting-freeze-drying method, show an interconnected porous structure and a high water-absorption capacity (swelling degree > 1200%). The thermal characterization indicates that the structure presents microphase separation, with PHBV microdomains located between the PVA network. The PHBV chains located in the microdomains are able to crystallize; even more after the addition of G nanosheets, which act as a nucleating agent. Thermogravimetric analysis indicates that the degradation profile of the semi-IPN is located between those of the neat components, with an improved thermal stability at high temperatures (>450 °C) after the addition of G nanosheets. The mechanical (complex modulus) and electrical properties (surface conductivity) significantly increase in the nanohybrid hydrogels with 0.2% of G nanosheets. Nevertheless, when the amount of G nanoparticles increases fourfold (0.8%), the mechanical properties diminish and the electrical conductivity does not increase proportionally, suggesting the presence of G aggregates. The biological assessment (C2C12 murine myoblasts) indicates a good biocompatibility and proliferative behavior. These results reveal a new conductive and biocompatible semi-IPN with remarkable values of electrical conductivity and ability to induce myoblast proliferation, indicating its great potential for musculoskeletal tissue engineering.

Super-Strong Hydrogel Composites Reinforced with PBO Nanofibers for Cartilage Replacement

Cartilage replacement materials exhibiting a set of demanding properties such as high water content, high mechanical stiffness, low friction, and excellent biocompatibility are quite difficult to achieve. Here, poly(p-phenylene-2,6-benzobisoxazole) (PBO) nanofibers are combined with polyvinyl alcohol (PVA) to form a super-strong structure with a performance that surpasses the vast majority of previously existing hydrogels. PVA-PBO composites with water contents in the 59-76% range exhibit tensile and compressive moduli reaching 20.3 and 4.5 MPa, respectively, and a coefficient of friction below 0.08. Further, they are biocompatible and support the viability of chondrocytes for 1 week, with significant improvements in cell adhesion, proliferation, and differentiation compared to PVA. The new composites can be safely sterilized by steam heat or gamma radiation without compromising their integrity and overall performance. In addition, they show potential to be used as local delivery platforms for anti-inflammatory drugs. These attractive features make PVA-PBO composites highly competitive engineered materials with remarkable potential for use in the design of load-bearing tissues. Complementary work has also revealed that these composites will be interesting alternatives in other industrial fields where high thermal and mechanical resistance are essential requirements, or which can take advantage of the pH responsiveness functionality.

Nanocellulose-reinforced, multilayered poly(vinyl alcohol)-based hydrophobic composites as an alternative sealing film

A flexible, hydrophobic, and multilayered poly(vinyl alcohol) (PVA) film evolved to replace a commercially available nonbiodegradable easy seal-paper (ES-PAPER) sealing film. First, environmentally friendly fillers, such as cellulose nanocrystals (CNCs) or cellulose nanofibers (CNFs), were added to produce PVA + CNC/CNF composites via blade coating and solution casting to strengthen the mechanical properties of PVA. Subsequently, biodegradable and hydrophobic materials, such as poly(ethylene glycol)-poly(lactic acid) (PEG-PLA) and neat PLA, were added to prepare multilayered PEG-PLA and PLA hydrophobic composites using double-sided solution casting. The hydrophobicity of PVA was enhanced through heat treatment. Finally, the mechanical properties of the as-prepared PVA film were compared with those of a commercially available ES-PAPER sealing film. PVA + CNC/CNF composites exhibit excellent transparency and mechanical properties, whereas PVA + CNCs 3.0 wt% have the highest Young's modulus and tensile strength, which are, respectively, 3% and 96% higher than the Young's modulus and tensile strength of an ES-PAPER sealing film. With regard to strain at break, the prepared PVA film also exhibited a value many times larger than that of the ES-PAPER sealing film because of good filler dispersibility, which significantly enhanced the durability of the sealing film.

How hydrogen-bonding interactions and nanocrystal aspect ratios influence the morphology and mechanical performance of polymer nanocomposites reinforced with cellulose nanocrystals

The performance of polymer nanocomposites reinforced with cellulose nanocrystals (CNCs) is complicated by several factors, primarily CNC-polymer and polymer-polymer interactions. Our current work specifically seeks to address the effects of CNC geometry, CNC-polymer and polymer-polymer interactions on the structure and non-linear mechanical performance of nanocomposites prepared using two water-soluble polymers, polyethylene oxide (PEO) and polyvinyl alcohol (PVA), having different morphological and structural characteristics. PEO and PVA are chosen since they are compatible with CNCs, however, they interact quite differently with CNCs and result in different reinforcement mechanisms. PEO and PVA interact with CNCs via a nucleating effect and H-bonding, which influence the polymer structure in two opposite directions. The nucleating effect tends to lead the polymer chains to form more ordered structures, whereas H-bonding interactions restrict the mobility of the polymer chains. Since PEO has weaker interactions amongst molecular chains than PVA, the properties of PEO are more significantly influenced by CNCs.

Flame Retardancy, Thermal and Mechanical Properties of Novel Intumescent Flame Retardant/MXene/Poly(Vinyl Alcohol) Nanocomposites

Poly(vinylphosphonic acid) (PVPA) and polyethylenepolyamine (PEPA) are used as novel intumescent flame retardants to improve the properties of MXene (2D Ti3C2Tx)/poly(vinyl alcohol) (PVA) nanocomposites. We investigated the flame-retardant properties, thermal stability, and mechanical properties of MXene/PVA nanocomposites. The results show that MXene was homogeneously dispersed in the PVA matrix containing PVPA and PEPA. PVPA and PEPA effectively improved the flame-retardant properties of MXene/PVA nanocomposites and they did not obviously change the thermal degradation of the MXene/PVA nanocomposites. Moreover, MXene improved the thermal stability of the PVA matrix. The elongation at break of MXene/PVA nanocomposites reached its maximum when the MXene mass fraction was 1.0 wt.%, regardless of whether PVPA and PEPA were present in the PVA matrix, whereas the tensile strength and Young’s modulus of MXene/PVA nanocomposites increased with the increase in MXene content in the PVA matrix.

A comprehensive investigation on cellulose nanocrystals with different crystal structures from cotton via an efficient route

The crystal structures of cellulose nanomaterials play an important role in their morphologies and applications, however, there was still lacking systematic research on preparing various crystalline allomorphs of cellulose nanocrystals with high thermal stability. Herein, the efficient synthesis route was presented to design various crystalline allomorphs of cellulose from cotton. And then, cellulose nanocrystals with different crystal structures (CNC-I, CNC-II, CNC-III_II, CNC-IV_II) were prepared by hydrogen peroxide hydrolysis of resultant cellulose. Overall, needle-like CNC-I (length of 180 ± 25 nm, diameter of 12 ± 2 nm), near-spherical CNC-II (diameter of 101 ± 12 nm), and spherical CNC-III_II (diameter of 22 ± 3 nm) and CNC-IV_II (diameter of 21 ± 2 nm) all exhibited remarkable dispersibility and thermal stability (T_max > 357 °C). This work provides a simple and low-cost synthesis route for various crystalline allomorphs of CNCs with high thermal stability from the same raw materials (cotton).

Sandwich-Structured, Hydrophobic, Nanocellulose-Reinforced Polyvinyl Alcohol as an Alternative Straw Material

An environmentally friendly, hydrophobic polyvinyl alcohol (PVA) film was developed as an alternative to commercial straws for mitigating the issue of plastic waste. Nontoxic and biodegradable cellulose nanocrystals (CNCs) and nanofibers (CNFs) were used to prepare PVA nanocomposite films by blade coating and solution casting. Double-sided solution casting of polyethylene-glycol–poly(lactic acid) (PEG–PLA) + neat PLA hydrophobic films was performed, which was followed by heat treatment at different temperatures and durations to hydrophobize the PVA composite films. The hydrophobic characteristics of the prepared composite films and a commercial straw were compared. The PVA nanocomposite films exhibited enhanced water vapor barrier and thermal properties owing to the hydrogen bonds and van der Waals forces between the substrate and the fillers. In the sandwich-structured PVA-based hydrophobic composite films, the crystallinity of PLA was increased by adjusting the temperature and duration of heat treatment, which significantly improved their contact angle and water vapor barrier. Finally, the initial contact angle and contact duration (at the contact angle of 20°) increased by 35% and 40%, respectively, which was a significant increase in the service life of the biodegradable material-based straw.

Statistical and Machine Learning-Driven Optimization of Mechanical Properties in Designing Durable HDPE Nanobiocomposites

The selection of nanofillers and compatibilizing agents, and their size and concentration, are always considered to be crucial in the design of durable nanobiocomposites with maximized mechanical properties (i.e., fracture strength (FS), yield strength (YS), Young’s modulus (YM), etc). Therefore, the statistical optimization of the key design factors has become extremely important to minimize the experimental runs and the cost involved. In this study, both statistical (i.e., analysis of variance (ANOVA) and response surface methodology (RSM)) and machine learning techniques (i.e., artificial intelligence-based techniques (i.e., artificial neural network (ANN) and genetic algorithm (GA)) were used to optimize the concentrations of nanofillers and compatibilizing agents of the injection-molded HDPE nanocomposites. Initially, through ANOVA, the concentrations of TiO₂ and cellulose nanocrystals (CNCs) and their combinations were found to be the major factors in improving the durability of the HDPE nanocomposites. Further, the data were modeled and predicted using RSM, ANN, and their combination with a genetic algorithm (i.e., RSM-GA and ANN-GA). Later, to minimize the risk of local optimization, an ANN-GA hybrid technique was implemented in this study to optimize multiple responses, to develop the nonlinear relationship between the factors (i.e., the concentration of TiO₂ and CNCs) and responses (i.e., FS, YS, and YM), with minimum error and with regression values above 95%.

Development and Characterization of Electrospun Fiber-Based Poly(ethylene-co-vinyl Alcohol) Films of Application Interest as High-Gas-Barrier Interlayers in Food Packaging

In the present study, poly(ethylene-co-vinyl alcohol) with 44 mol % ethylene content (EVOH44) was managed to be processed, for the first time, by electrospinning assisted by the coaxial technology of solvent jacket. In addition to this, different suspensions of cellulose nanocrystals (CNCs), with contents ranging from 0.1 to 1.0 wt %, were also electrospun to obtain hybrid bio-/non-bio nanocomposites. The resultant fiber mats were thereafter optimally annealed to promote interfiber coalescence at 145 °C, below the EVOH44 melting point, leading to continuous transparent fiber-based films. The morphological analysis revealed the successful distribution of CNCs into EVOH44 up to contents of 0.5 wt %. The incorporation of CNCs into the ethylene-vinyl alcohol copolymer caused a decrease in the crystallization and melting temperatures (TC and Tm) of about 12 and 7 °C, respectively, and also crystallinity. However, the incorporation of CNCs led to enhanced thermal stability of the copolymer matrix for a nanofiller content of 1.0 wt %. Furthermore, the incorporation of 0.1 and 0.5 wt % CNCs produced increases in the tensile modulus (E) of ca. 38% and 28%, respectively, but also yielded a reduction in the elongation at break and toughness. The oxygen barrier of the hybrid nanocomposite fiber-based films decreased with increasing the CNCs content, but they were seen to remain high barrier, especially in the low relative humidity (RH) regime, i.e., at 20% RH, showing permeability values lower than 0.6 × 10-20 m3·m·m-2·Pa-1·s-1. In general terms, an optimal balance in physical properties was found for the hybrid copolymer composite with a CNC loading of 0.1 wt %. On the overall, the present study demonstrates the potential of annealed electrospun fiber-based high-barrier polymers, with or without CNCs, to develop novel barrier interlayers to be used as food packaging constituents.

Immobilization of roselle anthocyanins into polyvinyl alcohol/hydroxypropyl methylcellulose film matrix: Study on the interaction behavior and mechanism for better shrimp freshness monitoring

The roselle anthocyanin extracts (RAE) were immobilized into polyvinyl alcohol (PVA)/hydroxypropyl methylcellulose (HPMC) film matrix, their interaction behavior and mechanism was fully understood for better shrimp freshness monitoring. Structural characterizations revealed RAE was firmly immobilized PVA/HPMC matrix by hydrogen bonds. With increasing RAE contents, dramatic increases of film thickness (from 15.90 ± 0.14 to 23.20 ± 3.35 μm), tensile strength (from 45.66 ± 1.07 to 56.98 ± 0.24 MPa), light barrier and active properties (increased by 83.18% for antioxidant and 146.91%, 59.18% for antibacterial activity against E. coli and S. aureus) were observed, while hydrophobic properties decreased significantly. Owing to great ammonia-sensitive ability, the PVA/HPMC/RAE (PHR) films were applied on shrimp freshness qualitative monitoring and greater visible color variations were identified with increasing RAE contents. Furthermore, mathematical models were established for quantitative monitoring. In conclusion, with the increasing RAE contents, the tighter interaction between RAE and PVA/HPMC matrix contributed to the better functional properties and freshness monitoring effects of PHR films.

Spherical vs rod-like cellulose nanocrystals from enzymolysis: A comparative study as reinforcing agents on polyvinyl alcohol

In this paper, we have isolated cellulose nanocrystallines (CNCs) with different morphologies by enzymatic hydrolysis, and prepared flexible and transparent nanocomposite films with PVA matrix via solution casting. By means of SEM, UV-vis, XRD, DTG, FT-IR and mechanical methods, the effects of rod-shaped cellulose nanocrystallines (RCNCs) and spherical cellulose nanocrystallines (SCNCs) on PVA nanocomposite films were compared systematically. The results showed CNCs with different morphologies had little effect on the transparency of the composite films, and the crystallinity fluctuated with the change of CNCs additive amount. Compared with the RCNCs, SCNCs had a better improve ability to the thermal stability of the composite films by promoting pyrolysis temperature 60-80 °C. On the contrary, the maximum mechanical properties of the composite films of RCNCs were much higher than those of SCNCs, and the Young's modulus of the PVA/RCNCs composite film were increased by 120.97 % in comparison with the pure PVA.

Hydrogen Bond Association to Prepare Flame Retardant Polyvinyl Alcohol Film with High Performance

It has always been the goal of flame retardant research to improve the flame retardancy of a polymer efficiently without compromising comprehensive properties such as mechanical properties. For polyvinyl alcohol (PVA), inspired by the multiple hydrogen bonding in spider silk, we design a new type of compound containing phosphorus and nitrogen with multiple hydrogen-bonding reaction sites (N,N',N''-tris(2-aminoethyl)phosphoric triamide (TE)) as it is flame retardant. The dynamic cross-linking structure is constructed, and the hyperdispersion of flame retardancy is achieved by the hydrogen bond self-assembly between TE and PVA, thus the high-performance flame retardant PVA is obtained. With only a 10 wt % addition of TE, the PVA film with a thickness of 0.15 mm can reach the UL94 VTM-0 level, and its tensile strength, ductility, and initial decomposition temperature can be increased by 33, 15, and 12 °C, respectively. In addition, the hydrogen-bonding effect and flame retardant mechanism are characterized and studied. This work overcomes the shortcomings of traditional flame retarding approaches and provides an effective strategy for the preparation of flame retardant polymers with an excellent performance.

Unveiling Modifications of Biomass Polysaccharides during Thermal Treatment in Cholinium Chloride : Lactic Acid Deep Eutectic Solvent

A deep analysis upon the chemical modifications of the cellulose and hemicelluloses fractions that take place during biomass delignification with deep eutectic solvents (DES) is lacking in literature, being this a critical issue given the continued research on DES for this purpose. This work intends to fill this gap by disclosing a comprehensive study on the chemical modifications of cellulose (microcrystalline cellulose and bleached kraft pulp) and hemicelluloses (xylans) during thermal treatment (130 °C) with cholinium chloride/lactic acid ([Ch]Cl/LA) at molar ratio 1 : 10, one of the best reported DES for biomass delignification. The obtained data revealed that [Ch]Cl/LA (1 : 10) has a negative impact on the polysaccharides fractions at prolonged treatments (>4 h), resulting on substantial modifications including the esterification of cellulose with lactic acid, shortening of fibers length, fibers agglomeration and side reactions of the hemicelluloses fraction (e. g., humin formation, lactic acid grafting). Wood delignification trials with [Ch]Cl/LA (1 : 10) at the same conditions also corroborate these findings. Moreover, the DES suffers degradation, including the formation of lactic acid derivatives and its polymerization. Therefore, short time delignification treatments are strongly recommended when using the [Ch]Cl/LA DES, so that a sustainable fractionation of biomass into high quality cellulose fibers, isolated lignin, and xylose/furfural co-production along with solvent recyclability could be achieved.

Enhanced anti-cancer activity by localized delivery of curcumin form PVA/CNCs hydrogel membranes: Preparation and in vitro bioevaluation

This study targets to develop curcumin-loaded polyvinyl alcohol/cellulose nanocrystals (PVA/CNCs) membrane as localized delivery system for breast/liver cancer. A novel strategy was developed for enhancing encapsulation capacity and maximizing therapeutic efficiency of curcumin-loaded PVA/CNCs membranes. Membranes were prepared by solution-casting method using citric acid as crosslinker. SEM revealed that PVA/CNCs ratio (80:20) was chosen as the optimum for loading curcumin. FT-IR indicated that, curcumin was incorporated into PVA/CNCs in amorphous-phase via intermolecular hydrogen bond between curcumin and membrane components. Curcumin showed biphasic-release through burst-release of 41% of curcumin during the first hour, followed by sustained-release of 70% and 94% during 24 h and 48 h, respectively. In vitro cytotoxicity of PVA/CNCs/Curcumin membrane exhibited a selective inhibition proliferation of breast and liver cancer cells in a concentration-dependent without any toxic effect on normal cells. At high concentration (8 mg/ml) of PVA/CNCs/Curcumin, reduced viability to 35% and 7% of MCF-7 and Huh-7 cells, respectively; meanwhile high HFB-4 normal cell viability ≥80% was investigated. Antimicrobial activity of PVA/CNCs/Curcumin was investigated by multi-drug-resistant strains, and MIC values. PVA/CNCs/Curcumin membranes with concentration (40 mg/ml) showed broad-spectrum antimicrobial activities, thus inhibited ~96-99% of microbial growth. PVA/CNCs/Curcumin membranes could be as promised anti-infective biomaterials for breast and liver cancer wound healing.

Novel Semi-Interpenetrated Polymer Networks of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate)/Poly (Vinyl Alcohol) with Incorporated Conductive Polypyrrole Nanoparticles

This paper reports the preparation and characterization of semi-interpenetrating polymer networks (semi-IPN) of poly(3-hydroxybutirate-co-3-hydroxyvalerate), PHBV, and poly (vinyl alcohol), PVA, with conductive polypirrole (PPy) nanoparticles. Stable hybrid semi-IPN (PHBV/PVA 30/70 ratio) hydrogels were produced by solvent casting, dissolving each polymer in chloroform and 1-methyl-2-pyrrolidone respectively, and subsequent glutaraldehyde crosslinking of the PVA chains. The microstructure and physical properties of this novel polymeric system were analysed, including thermal behaviour and degradation, water sorption, wettability and electrical conductivity. The conductivity of these advanced networks rose significantly at higher PPy nanoparticles content. Fourier transform infrared spectroscopy (FTIR) and calorimetry characterization indicated good miscibility and compatibility between all the constituents, with no phase separation and strong interactions between phases. A single glass transition was observed between those of pure PHBV and PVA, although PVA was dominant in its contribution to the glass transition process. Incorporating PPy nanoparticles significantly reduced the hydrogel swelling, even at low concentrations, indicating molecular interactions between the PPy nanoparticles and the hydrogel matrix. The PHBV/PVA semi-IPN showed higher thermal stability than the neat polymers and PHBV/PVA blend, which also remained in the tertiary systems.

Comparison of polyvinyl alcohol films reinforced with cellulose nanofibers derived from oil palm by impregnating and casting methods

Cellulose nanofibers (CNFs) derived from oil palm trees were utilized to reinforce polyvinyl alcohol (PVA) films by either casting or impregnating. CNFs derived from trunks of the oil palm tree were dispersed well in a PVA film by the casting method. Using the impregnating method, however, a sandwich construction with CNFs and PVA was obtained, which was confirmed using attenuated total reflectance Fourier transform infrared spectroscopy. The thermal stability, tensile strength, and Young's moduli of the PVA/CNF nanocomposite films were increased by compounding CNFs at different concentrations using both the casting and impregnating methods. However, the impregnated nanocomposite films showed higher thermal melting temperature and higher tensile toughness than those obtained by the casting method. No obvious differences appeared in the X-ray diffraction patterns or thermal decomposition behavior between the impregnated and cast nanocomposite films. In addition, adding CNFs was confirmed to increase the crystallinity of PVA.

Enzymatically produced cellulose nanocrystals as reinforcement for waterborne polyurethane and its applications

Waterborne polyurethanes (WBPUs) have been proposed as ecofriendly elastomers with several applications in coatings and adhesives. WBPU's physicochemical properties can be enhanced by the addition of cellulose nanocrystals (CNCs). The way CNCs are isolated has a strong effect on their properties and can determine their role as reinforcement. In this work, CNCs produced using ancestral endoglucanase (EnCNCs) were used as reinforcement for WBPU and compared with CNC produced by sulfuric acid hydrolysis (AcCNC). The enzymatic method produced highly thermostable and crystalline CNCs. The addition of small contents of EnCNCs improved the thermomechanical stability and mechanical properties of WBPUs, even better than commercial AcCNCs. Besides, WBPU reinforced by adding EnCNCs was studied as a coating for paper materials, increasing its abrasion resistance and as electrospun nanocomposite mats where EnCNCs helped maintaining the morphology of the fibers.

Biodegradable cellulose I (II) nanofibrils/poly(vinyl alcohol) composite films with high mechanical properties, improved thermal stability and excellent transparency

Cellulose nanofibrils (CNFs) with cellulose I and II allomorphs were efficiently prepared by sulfuric acid hydrolysis of eucalyptus cellulose under three different conditions followed by mechanical treatments: (i) classical sulfuric acid hydrolysis of cellulose I (CNF-I), (ii) sulfuric acid hydrolysis of mercerized cellulose II (MNF-II), and (iii) solubilization and hydrolysis of cellulose I by concentrated sulfuric acid and subsequent recrystallization in water (RNF-II). Crystal structure, surface chemistry, morphology and thermal properties of three CNFs were investigated and compared. Three CNFs of 2-10 wt% were mixed with PVA to prepare biodegradable composite films. CNF allomorph had significant impact on crystal structure, mechanical and thermal properties of the PVA composites. The maximum Young's modulus of CNF-I/PVA, RNF-II/PVA and MNF-II/PVA were increased by 62, 32 and 44%, respectively. Addition of CNFs raised onset degradation temperature (T_onset) and thermal decomposition temperature (T_max) of PVA nanocomposite, while decreased the melting temperature (T_m). Temperature window (T_onset - T_m) for the melt processing of nanocomposites (10 wt% CNF loading) were increased 2.8, 3.2 and 2.5 times for CNF-I/PVA, RNF-II/PVA and MNF-II/PVA, respectively. All composite films remained excellent transparency with addition of CNFs. This comparative study provided important knowledge of selecting CNF allomorph for fabrication of high-performance CNF/PVA composites.

Novel eco-friendly electrospun nanomagnetic zinc oxide hybridized PVA/alginate/chitosan nanofibers for enhanced phenol decontamination

In the current study, poly(vinyl alcohol)/alginate/chitosan (PVA/Alg/CS) composite nanofiber was immobilized with six different ratios of nanomagnetic zinc oxide (M-ZnO) (0 wt%, 0.2 wt%, 0.4 wt%, 0.6 wt%, 0.8 wt%, and 1 wt%) via the electrospinning technique. The various fabricated composite (M-6) nanofibers were characterized using Fourier transform infrared (FTIR), X-ray diffractometer (XRD), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), atomic force microscope (AFM), thermogravimetric analysis (TGA), mechanical testing machine, and optical contact angle measurement. The fabricated composite nanofibers were applied for the adsorption of phenol from aqueous solutions. The 1.0 wt% M-ZnO/PVA/Alg/CS composite nanofibers were selected as the best phenol adsorbent with removal percentage of 84.22%. The influence of different processing parameter such as contact time, composite nanofiber dosage, pH, initial pollutant concentration, and temperature were examined. Increasing nanofiber dosage and the solution temperature was found to enhance the phenol adsorption onto the prepared nanocomposites. The maximum percentage of phenol removal was achieved at 84.22% after 90 min. Meanwhile, the maximum monolayer adsorption capacity (at pH = 5.0) was estimated to be 10.03 mg g^-1 at 25 °C. Kinetic, isotherm, and thermodynamic studies were designated to proof the endothermic, spontaneous, and thermodynamically nature of the phenol adsorption process. These outcomes indicate the effectiveness of the fabricated M-ZnO/PVA/Alg/CS nanofibers as adsorbent materials for phenol from aqueous solutions.

Recent studies on modified cellulose/nanocellulose epoxy composites: A systematic review

Cellulose and its derivatives are widely explored for films and thickening of pharmaceutical solutions, in paints, as reinforcement in composites, among others. This versatility is due to advantages such as renewability, low cost, and environmental friendliness. When used in polymer composites, due to the hydrophilic character of the cellulose, surface chemical modification is highly recommended to improve its compatibility with the polymeric matrix. Hence, this paper presents a systematic review of chemically modified cellulose/epoxy resin composites focusing on the last five years. The investigation followed the PRISMA protocol that delivers a meticulous summary of all available primary research in response to a research question. After including/excluding steps, thirty-six studies were included in the review. The results were presented focusing on thermal, mechanical and dynamic-mechanical properties of the composites. In brief, this methodology helped identifying the main gaps in knowledge in that field.

Preparation of lignin containing cellulose nanofibers and its application in PVA nanocomposite films

Lignin containing cellulose nanofibers (LCNFs) were successfully prepared from wheat straw using an acid hydrotrope of p-toluene sulfonic acid (p-TsOH) combined with ultrasonication. p-TsOH pretreatment was applied below 80 °C to selectively remove hemicellulose and lignin and generate purified cellulose fibers containing approximately 15% lignin. Subsequently, high-intensity ultrasonication was used for <6 min to effectively defibrillate the p-TsOH-pretreated cellulose fibers to nanoscale fibers. AFM and TEM analyses showed that the diameter distribution of the resultant nanofibers decreased with the increase in ultrasonic intensity. The FTIR and XRD results indicated that the molecular structures and cellulose crystallinity were not changed during the ultrasonic process. An amount of 5 wt% of the obtained LCNFs was introduced into a polyvinyl alcohol (PVA) matrix. The resulting nanocomposite products exhibited improved thermal performance and surface properties compared with the pure PVA matrix. The mechanical properties, including the tensile stress and Young's modulus, were enhanced significantly, although the elongation at the break was slightly decreased. PVA composites with the addition of LCNFs are expected to be used in a variety of fields, such as biodegradable plastics, pharmaceutical carrier, filtration media and packaging materials.

Cellulose nanocrystal/plant oil polymer composites with hydrophobicity, humidity-sensitivity, and high wet strength

The preparation of high-performance cellulose nanocrystals (CNCs)/plant oil-derived polymer composites is still a challenge, due to their poor compatibility. Here, by designing amide groups and epoxy groups on sunflower oil derived polymers, appropriate interfacial hydrogen bond interactions between the polymers and CNCs were constructed, where CNCs were homogenously dispersed in polymer matrix. Tensile tests and DMA results revealed that the incorporation of CNCs into sunflower oil derived epoxy polymers significantly enhanced the tensile strength and storage modulus. More importantly, nanocomposites with 50 wt% CNCs are still hydrophobic, which not only show a fast and reversible humidity induced modulus switch, but also exhibit high wet strength (19.9 MPa) after equilibrium water adsorption. The present work revealed that proper designed CNCs/plant oil polymer nanocomposites are good candidates for high performance and functional materials, which are able to replace petroleum-based materials in various fields.

Self-Healable Conductive Nanocellulose Nanocomposites for Biocompatible Electronic Skin Sensor Systems

Electronic skins are developed for applications such as biomedical sensors, robotic prosthetics, and human-machine interactions, which raise the interest in composite materials that possess both flexibility and sensing properties. Polypyrrole-coated cellulose nanocrystals and cellulose nanofibers were prepared using iron(III) chloride (FeCl₃) oxidant, which were used to reinforce polyvinyl alcohol (PVA). The combination of weak H-bonds and iron coordination bonds and the synergistic effect of these components yielded self-healing nanocomposite films with robust mechanical strength (409% increase compared to pure PVA and high toughness up to 407.1%) and excellent adhesion (9670 times greater than its own weight) to various substrates in air and water. When damaged, the nanocomposite films displayed good mechanical (72.0-76.3%) and conductive (54.9-91.2%) recovery after a healing time of 30 min. More importantly, the flexible nanocomposites possessed high strain sensitivity under subtle strains (<48.5%) with a gauge factor (GF) of 2.52, which was relatively larger than the GF of ionic hydrogel-based skin sensors. These nanocomposite films possessed superior sensing performance for real-time monitoring of large and subtle human motions (finger bending motions, swallowing, and wrist pulse); thus, they have great potentials in health monitoring, smart flexible skin sensors. and wearable electronic devices.