Application of cellulose acetate for controlled release of thymol

Carvacrol and thymol effect in vapor phase on Escherichia coli and Salmonella serovar Typhimurium growth inoculated in a fresh salad

This study aimed to evaluate the antimicrobial effect of thymol and carvacrol in inhibiting Escherichia coli and Salmonella serovar Typhimurium inoculated on a fresh green salad through the vapor phase. A film-forming solution was prepared by dissolving starch, sorbitol, and variying concentrations of carvacrol, thymol, and a mixture of both. The film-forming solution containing the respective antimicrobial agent was then added lid, which was sealed rigidly and hermetically to achieve different concentrations (105 mg/L of air of carvacrol, 105 mg/L of air of thymol, and a mixture of 52 mg/L of air of carvacrol and 52 mg/L of air of thymol). Each active package contained fresh green salad inoculated with E. coli or Salmonella serovar Typhimurium. The active packages were then sealed and refrigerated at a temperature of 6 °C for 48 h. Growth/inhibition curves were modelled using the Weibull equation, and consumer acceptance was evaluated. Carvacrol can reduce up to 0.5 log-cycles, while thymol can reach almost 1 log cycle. Blending the components with half the concentration has a synergistic effect, inhibiting up to 2.5 log cycles. Consumer ratings revealed no significant differences between the packages. However, the average score was 5.4 on a 9-point hedonic scale, evaluators' comments did not indicate dislike or a strong taste characteristic of thymol and carvacrol.

Cornstarch aerogels with thymol, citronellol, carvacrol, and eugenol prepared by supercritical CO2- assisted techniques for potential biomedical applications

This study focuses on the development of bioactive materials using environmentally friendly techniques, renewable, biocompatible, and biodegradable polysaccharide, as well as natural bioactive compounds (NBCs) found in plant extracts. First, cornstarch aerogels with a porosity of 86 % and a specific surface area of 225 m2/g were produced via supercritical CO2- assisted drying. Further, thymol, citronellol, carvacrol, and eugenol were incorporated into the aerogels by supercritical CO2- assisted impregnation, which allowed variation in loadings of NBCs (12.8-17.6 %). Interaction between cornstarch aerogels and NBCs determined impregnation rate, pore wall thickness (in the range 18-95 nm), liquid absorption capacity (from 265 to 569 %), dehydration mass loss, and release in phosphate-buffered saline. Controlled release of NBCs was maintained over a 3-day period. Moreover, impregnated aerogels showed a significant antioxidant effect with the highest value for DPPH radical inhibition of 25.5 % determined for the aerogels impregnated with eugenol. Notable antimicrobial activity against tested Gram-negative bacteria, Gram-positive bacteria, and fungi was also observed, being the highest for thymol-loaded aerogel with the diameter of the inhibition zones of up to 37.5 mm. This work shows a promising green approach for the production of bioactive two-component starch-based materials for potential applications in skin infection treatment.

Mechanism of multicyclic β-carotene impregnation into corn starch aerogels via supercritical CO2 with mathematical modeling

β-carotene, a natural dye renowned for its antioxidant and provitamin A activities, is hindered from direct use in food and drug products due to its susceptibility to oxidation, easy isomerization under light, heat, or acidic conditions, as well as its low water solubility and oral bioavailability. In this study, we addressed these challenges by loading β-carotene into corn starch aerogels via supercritical carbon dioxide (sc-CO2) and assessed its loading contributions through adsorption during contact time and precipitation during depressurization. The loading process was studied under two cycles at pressure of 30 MPa, temperature of 40 °C, depressurization rate of 0.4 MPa/min, and co-solvent (ethanol) mass percentage of 1.2 %. Experiments found adsorption minimally contributed to impregnation, while precipitation became the primary loading mechanism. The subsequent work focused on a mathematical model describing β-carotene loading into corn starch aerogels via precipitation, using the law of conservation of mass and classical nucleation theory. The model shows that using pure CO2 results in a loading efficiency of 0.10 mg β-carotene/g aerogel, while with CO2 and 1.2 % ethanol as the co-solvent, the loading efficiency increases threefold to 0.30 mg β-carotene/g aerogel.

Real-time in vivo monitoring of the antimicrobial action of combination therapies in the management of infected topical wounds

The increasing prevalence of non-healing infected wounds has become a serious concern in the clinical practice, being associated to population aging and to the rising prevalence of several chronic conditions such as diabetes. Herein, the evaluation of the bactericidal and antibiofilm effects of the natural antiseptic terpenes thymol and farnesol standing alone or in combination with the standard care antiseptic chlorhexidine was carried out both in vitro and in vivo. The in vitro combinatorial treatment of chlorhexidine associated with those terpenes against Staphylococcus aureus in its planktonic and sessile forms demonstrated a superior antibacterial activity than that of chlorhexidine alone. Real-time in vivo monitoring of infection progression and antimicrobial treatment outcomes were evaluated using the bioluminescent S. aureus strain Xen36. In vivo studies on infected wound splinting murine models corroborated the superior bactericidal effects of the combinatorial treatments here proposed. Moreover, the encapsulation of thymol in electrospun Eudragit® S100 (i.e., a synthetic anionic copolymer of methacrylic acid and ethyl acrylate)-based wound dressings was also carried out in order to design efficient antimicrobial wound dressings.

Unraveling the Adsorption Behavior of Thymol on Carbon and Silica Nanospheres for Prolonged Antibacterial Activity: Experimental and DFT Studies

Functionalization of thymol (Thy) on nanocarriers is a key step in achieving prolonged antimicrobial activity. This requires nanomaterials with uniform particle diameters and suitable thymol sorption. Herein, hollow carbon (HC) and SiO2-carbon core-shell (SiO2@C) were investigated due to their diverse morphologies and ease of surface modification. HC (14 ± 1 nm size) and SiO2@C (10 ± 1.5 nm size) were synthesized by the Stöber method before thymol was loaded by incipient wetness impregnation. Nanoparticle physicochemical properties were characterized by advanced techniques, including X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS). Adsorption energies of thymol on the carbon and SiO2 surfaces were elucidated by density functional theory (DFT) simulations. Moreover, the in vitro thymol release profiles and antibacterial activity were evaluated. The experimental results indicated that the oxy-carbon surface species of HC led to longer thymol release profiles than the -OH group of SiO2@C. The DFT calculations revealed that the weaker physical interaction of thymol on HC was better for drug release than that on SiO2@C. Thus, a longer thymol release profile of HC with hollow structures showed better antibacterial performance against Gram-positive bacteria Staphylococcus aureus than that of SiO2@C with core-shell structures. This work confirms the important role of carbon morphology and specific functional groups in thymol release profiles for the further development of inhibition products.

Chitosan-thymol nanoparticle with pH responsiveness as a potential intelligent botanical fungicide against Botrytis cinerea

The practical application of essential oils (EOs) as an alternative for synthetic pesticides in agricultural production is severely limited because of their instability, high volatility, and water insolubility. Nanoencapsulation of EOs is an important strategy to overcome these limitations. In view of this, this study aimed to develop chitosan-thymol nanoparticle (NCS-Thy) with pH-responsive which can be used as an intelligent botanical fungicide to control Botrytis cinerea. The NCS-Thy nanoparticle was prepared by ionic crosslinking method with the loading capacity and encapsulation efficiency of 29.87% and 41.92%, respectively. The synthesized NCS-Thy nanoparticle was further characterized by Fourier transform infrared spectroscopy analysis, transmission electron microscopy observation, and dynamic lights scattering. The results of release kinetics and antifungal activity of NCS-Thy under different pH conditions were determined. The results showed that the NCS-Thy nanoparticle had excellent pH-responsiveness and can release more thymol under acidic conditions formed by B. cinerea, thereby achieving higher antifungal effects. Therefore, compared with unencapsulated thymol, the NCS-Thy nanoparticle had higher antifungal activity against B. cinerea in vitro. In addition, both the protective and curative efficacies of detached leaf test and pot experiment were significantly higher than those of unencapsulated thymol. Among them, the protective efficacy of NCS-Thy in the pot experiment was 78.73%, which was significantly higher than that of unencapsulated thymol with 61.13%. Therefore, the pH-responsive chitosan-thymol nano-preparation had a promising prospect of application in practical management of gray mold as an intelligent botanical fungicide.

Cellulose acetate/silica composites: Physicochemical and biological characterization

Cellulose acetate is of remarkable scientific interest, becoming more useful when is used in obtaining of the composite materials containing nanoparticles, as result of its improved properties. Thus, cellulose acetate/silica composite films obtained by casting the solutions of cellulose acetate (CA)/tetraethyl orthosilicate (TEOS) in different mixing ratios were analyzed in this paper. The impact of TEOS addition, and implicitly of the silica nanoparticles on the mechanical strength, water vapor sorption properties and antimicrobial activity of the cellulose acetate/silica films were mainly monitored. The results of the tensile strength tests were discussed in correlation with data obtained from Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis. It was found that samples with low TEOS content show improved mechanical strength compared to samples with high amounts of TEOS. The microstructural characteristics of the studied films affect their moisture sorption capacity so that the weight of the adsorbed water increases with the addition of TEOS. These features are complemented with the antimicrobial activity against Staphylococcus aureus and Escherichia coli bacterial species. The obtained data show that the cellulose acetate/silica films, and especially those with low silica content have improved properties that can recommend them for applications in the biomedical field.

Release Kinetics Model Fitting of Drugs with Different Structures from Viscose Fabric

(1) Background: It is simpler and more environmentally friendly to use supercritical CO₂ fluid technology to process skincare viscose fabrics. Therefore, it is significant to study the release properties of drug-loaded viscose fabrics to choose suitable skincare drugs. In this work, the release kinetics model fittings were investigated in order to clarify the release mechanism and provide a theoretical basis for processing skincare viscose fabrics with supercritical CO₂ fluid. (2) Methods: Nine kinds of drugs with different substituent groups, different molecular weights, and different substitution positions were loaded onto viscose fabrics using supercritical CO₂ fluid. Then, the drug-loaded viscose fabrics were placed in an ethanol medium, and the release curves were drawn. Finally, the release kinetics were fitted using zero-order release kinetics, the first-order kinetics model, the Higuchi model, and the Korsmeyer-Peppas model. (3) Results: The Korsmeyer-Peppas model was the best-fitting model for all the drugs. Drugs with different substituent groups were released via a non-Fickian diffusion mechanism. On the contrary, other drugs were released via a Fickian diffusion mechanism. (4) Conclusions: In view of the release kinetics, it was found that the viscose fabric can swell when a drug with a higher solubility parameter is loaded onto it using supercritical CO₂ fluid, and the release rate is also slower.

Microbiological, thermal and mechanical performance of cellulose acetate films with geranyl acetate

The present work concerns to investigate the microbiological, thermal and mechanical behavior of cellulose acetate films obtained with addition of 0.5 % (v/v) and 1.0 % (v/v) of geranyl acetate by the casting technique. The antimicrobial activities of the polymeric films were assessed against Staphylococcus aureus and Escherichia coli bacteria and against Aspergillus flavus fungal. The achieved results show that the films presented antibacterial and antifungal activities. Moreover, the incorporation of the geranyl acetate in the polymeric films was confirmed by FTIR and TGA technique, while DSC analysis pointed out the compatibility between the geranyl acetate and cellulose acetate. The addition of the geranyl acetate did not modify the mechanical behavior of the cellulose acetate films concerning stiffness and tensile strength. These results suggest that this new material is promising for future applications in biomedical devices and food packaging.

The use of essential oils in chitosan or cellulose-based materials for the production of active food packaging solutions: a review

In recent decades, interest in sustainable food packaging systems with additional functionality, able to increase the shelf life of products, has grown steadily. Following this trend, the present review analyzes the state of the art of this active renewable packaging. The focus is on antimicrobial systems containing nanocellulose and chitosan, as support for the incorporation of essential oils. These are the most sustainable and readily available options to produce completely natural active packaging materials. After a brief overview of the different active packaging technologies, the main features of nanocellulose, chitosan, and of the different essential oils used in the field of active packaging are introduced and described. The latest findings about the nanocellulose- and chitosan-based active packaging are then presented. The antimicrobial effectiveness of the different solutions is discussed, focusing on their effect on other material properties. The effect of the different inclusion strategies is also reviewed considering both in vivo and in vitro studies, in an attempt to understand more promising solutions and possible pathways for further development. In general, essential oils are very successful in exerting antimicrobial effects against the most diffused gram-positive and gram-negative bacteria, and affecting other material properties (tensile strength, water vapor transmission rate) positively. Due to the wide variety of biopolymer matrices and essential oils available, it is difficult to create general guidelines for the development of active packaging systems. However, more attention should be dedicated to sensory analysis, release kinetics, and synergetic action of different essential oils to optimize the active packaging on different food products. © 2022 The Authors. Journal of The Science of Food and Agriculture published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Supercritical CO2 Impregnation of Thymol in Thermoplastic Starch-Based Blends: Chemico-Physical Properties and Release Kinetics

The aim of the present study was to investigate starch-based materials, prepared in an environmentally friendly way and from renewable resources, suitable for the development of biodegradable active food packaging. For this purpose, a bioactive compound (thymol) was incorporated into thermoplastic starch (TPS) and a TPS blend with poly (ε-caprolactone) (TPS-PCL) by the supercritical CO₂ (scCO₂) impregnation process. Impregnation experiments with scCO₂ were carried out at a pressure of 30 MPa and temperatures in the range of 40-100 °C during 1 to 20 h. The structural, morphological, and thermal properties of the obtained materials were comprehensively evaluated. Bioactive component release kinetic studies were performed in water at 6 °C and 25 °C. It was shown that the scCO₂ impregnation process could be successfully employed for thymol loading into TPS and TPS-PCL. The process was significantly influenced by the operating temperature and time as well as content of PCL. The samples showed a controlled release of thymol within seven days with a higher amount of released thymol from the TPS-PCL blend. The obtained materials are solvent-free and release the bioactive component in a controlled manner.

Robust Electrospinning-Constructed Cellulose Acetate@Anthocyanin Ultrafine Fibers: Synthesis, Characterization, and Controlled Release Properties

Anthocyanin has attracted increasing attention due to its superior biological activity. However, the inherently poor stability of anthocyanin limits its practical applications. In this study, a fast and straightforward method was developed to improve the stability of anthocyanin. Cellulose acetate ultrafine fiber-loaded anthocyanin (CA@Anthocyanin UFs) was prepared by robust electrospinning, and the potential application of cellulose acetate ultrafine fibers (CA UFs) as a bioactive substance delivery system was comprehensively investigated. The experimental results showed that CA@Anthocyanin UFs had protective effects on anthocyanin against temperature, light, and pH. The results of the artificially simulated gastric fluid (pH = 2.0) indicated that the CA@Anthocyanin UFs had a controllable release influence on anthocyanin. A 2,2-Diphenyl-1-picrylhydrazyl (DPPH) radical-scavenging assay suggested that the CA@Anthocyanin UFs still had an excellent antioxidant activity similar to anthocyanin. This work demonstrated the potential application of robust electrospinning-constructed cellulose acetate ultrafine fibers in bioactive substance delivery and controlled release systems, as well as its prospects in green packaging due to the nature of this environmentally friendly composite.

Supercritical Fluid Extraction from Zataria multiflora Boiss and Impregnation of Bioactive Compounds in PLA for the Development of Materials with Antibacterial Properties

In this research, the extraction with supercritical carbon dioxide (SC-CO2) and the subsequent impregnation of the extracted bioactive compounds from Zataria multiflora Boiss (Z. multiflora) into polylactic acid (PLA) films was investigated. The effects of temperature (318 and 338 K), pressure (15 and 25 MPa) and cosolvent presence (0 and 3 mol%) on the extraction yield were studied. The SC-CO2 assisted impregnation runs were carried out in a discontinuous mode at different pressure (15 and 25 MPa), temperature (318 and 328 K), and time (2 and 8 h) values, using 0.5 MPa min−1 as a constant value of depressurization rate. ANOVA results confirmed that pressure, temperature, and time influenced the extraction yield. Moreover, antioxidant activities of extracts of Z. multiflora were evaluated using 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assays. In addition, the antibacterial activities of the extracts were screened against standard strains of Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). The results of this investigation indicated that extracts obtained from the aerial parts of Z. multiflora possessed antioxidant and antibacterial properties. The impregnated samples presented strong antibacterial activity against the selected microorganisms.

A systematic review and meta-analysis of the effect of thymol as an anti-inflammatory and wound healing agent: A review of thymol effect on inflammation and wound healing: A review of thymol effect on inflammation and wound healing

Thymol (THY) exhibits antibacterial and antioxidant properties. Recent studies have also shown that THY presents anti-inflammatory and healing properties. This review focused on in vitro and in vivo investigations related to THY utilization, as an anti-inflammatory and/or wound healing agent. PubMed, WebOfScience, and Scopus were examined. Independent reviewers conducted all diagram steps. PRISMA was followed for data extraction. RoB 2 and SYRCLE were utilized to assess the risk of bias for in vitro and animal studies. Meta-analysis was performed for in vitro and in vivo articles that investigated THY as an anti-inflammatory agent. Thirty-six and 15 articles were included in the qualitative analysis and meta-analysis, respectively. Studies showed high risk of bias related to sampling, allocation procedures, randomization, and blinding. Even so, for in vitro studies, significant result was observed for IL-2. For in vivo studies, significant results were found for IL-1, IL-17, TNF-α, AST, MPO, and CRP, with higher levels noticed in control groups. THY presents significant properties as anti-inflammatory, ameliorating affections of the digestive system, cardiovascular problems, respiratory system and dermal damages, and burns. Researches are needed to clarify THY dose-response relationship and its mechanism of action, especially in the application of THY as a healing agent.

Antioxidant and antibacterial properties of essential oils-loaded β-cyclodextrin-epichlorohydrin oligomer and chitosan composite films

Chitosan (CS) is becoming increasingly popular in food packaging due to its natural degradability and great film-forming properties. Nevertheless, its poor antibacterial properties and inadequate antioxidant properties prevent it from being used effectively. In this study, β-cyclodextrin-epichlorohydrin (β-CD-EP) oligomers were prepared and encapsulated with natural essential oils cinnamaldehyde and thymol, and then the inclusion complexes (IC) were incorporated into chitosan in various contents to afford a series of CS-IC composite films. The impacts of IC on the morphological, mechanical, thermal, and water resistance properties, antioxidant and antibacterial activities of chitosan films, as well as the loading and sustained release behavior of IC, were thoroughly examined. The results turned out that the essential oils were well-loaded with high encapsulation efficiency and showed a significant slow-release effect. It was also found that the tensile strength and the elongation at break decreased with increasing IC contents, while the thermal stability was enhanced. The incorporation of IC dramatically promoted the antioxidant and antibacterial properties of the chitosan films towards Gram-positive bacteria. Based on our findings, chitosan films containing essential oils-loaded β-CD-EP oligomers may serve as an effective food packaging material.

Supercritical Foaming and Impregnation of Polycaprolactone and Polycaprolactone-Hydroxyapatite Composites with Carvacrol

Polycaprolactone (PCL) and polycaprolactone-hydroxyapatite (PCL-HA) scaffolds were produced by foaming in supercritical carbon dioxide (scCO2) at 20 MPa, as well as in one-step foaming and impregnation process using carvacrol as an antibacterial agent with proven activity against Gram-positive and Gram-negative bacteria. The experimental design was developed to study the influence of temperature (40 °C and 50 °C), HA content (10 and 20 wt.%), and depressurization rate (one and two-step decompression) on the foams’ morphology, porosity, pore size distribution, and carvacrol impregnation yield. The characterization of the foams was carried out using scanning electron microscopy (SEM, SEM-FIB), Gay-Lussac density bottle measurements, and Fourier–transform infrared (FTIR) analyses. The obtained results demonstrate that processing PCL and PCL-HA scaffolds by means of scCO2 foaming enables preparing foams with porosity in the range of 65.55–74.39% and 61.98–67.13%, at 40 °C and 50 °C, respectively. The presence of carvacrol led to a lower porosity. At 40 °C and one-step decompression at a slow rate, the porosity of impregnated scaffolds was higher than at 50 °C and two- step fast decompression. However, a narrower pore size distribution was obtained at the last processing conditions. PCL scaffolds with HA resulted in higher carvacrol impregnation yields than neat PCL foams. The highest carvacrol loading (10.57%) was observed in the scaffold with 10 wt.% HA obtained at 50 °C.

Modification of CaCO3 and CaCO3 pin-coated cellulose paper under supercritical carbon dioxide-ethanol mixture for enhanced NO2 capture

In this work, we examine two modifications of fine-ground calcium carbonate material (GCC) in order to enhanced sorption of NO₂ and subsequent reaction properties toward NO₂^-/NO₃^- formation by firstly exposing the GCC to supercritical (sc) CO₂ in order to increase particle surface area, a choice specifically made to avoid altering the surface chemistry, and secondly considering the potential advantage of using a surface coupling agent toward NO₂. The modification by the coupling agent amino silane (AMEO silane) was applied in a supercritical CO₂-ethanol mixture. The samples were characterised before and after modification by field emission scanning electron microscopy (FESEM), specific surface area determination (BET nitrogen adsorption), ATR-FTIR spectroscopy and ion chromatography to reveal the effects of the surface modification(s) on the morphology, surface textural properties and sorption versus reaction properties with NO₂. The performance of the treated sorbents for NO₂ capture was evaluated at room temperature. Results show that reactivity of NO₂ with GCC was observed to increase as a function of increased surface area resulting from scCO₂ exposure, but that the presence of AMEO silane on the surface, while enhancing initial adsorption of NO₂ was seen subsequently to act to block reactivity. Thus, judicious use of coupling agent can provide desired rapid initial adsorption of the gas, but the goal of long-term CaCO₃-consuming reactivity, so as to prolong the uptake of NO₂ beyond surface saturation alone, is achieved by increasing surface area while retaining chemical-free exposed CaCO₃ surface.

Cellulose Acetate Membranes Modification by Aminosilane Grafting in Supercritical Carbon Dioxide towards Antibiofilm Properties

The study explores the grafting of cellulose acetate microfiltration membranes with an aminosilane to attain antibiofilm properties. The grafting reaction was performed in the supercritical carbon dioxide used as a transport and reaction medium. The FTIR analyses and dissolution tests confirmed the covalent bonding between the aminosilane and polymer. The membranes' microstructure was investigated using a dual-beam SEM and ion microscopy, and no adverse effects of the processing were found. The modified membranes showed a more hydrophilic nature and larger water permeate flow rate than the neat cellulose acetate membranes. The tests in a cross-filtration unit showed that modified membranes were considerably less blocked after a week of exposure to Staphylococcus aureus and Escherichia coli than the original ones. Microbiological investigations revealed strong antibiofilm properties of the grafted membranes in experiments with Staphylococcus aureus, Listeria monocytogenes, Escherichia coli, and Salmonella Enteritidis.

Comparison of Aging Resistance and Antimicrobial Properties of Ethylene-Norbornene Copolymer and Poly(Lactic Acid) Impregnated with Phytochemicals Embodied in Thyme (Thymus vulgaris) and Clove (Syzygium aromaticum)

The effects of plant-based extracts on the solar aging and antimicrobial properties of impregnated ethylene-norbornene (EN) copolymer and poly(lactic acid) (PLA) were investigated. In this study, the impregnation yield of polyolefin, lacking in active centers capable of phytochemical bonding, and polyester, abundant in active sides, was measured. Moreover, two different extracts plentiful in phytochemicals-thyme (TE) and clove (CE)-were employed in the solvent-based impregnation process. The effect of thymol and eugenol, the two main compounds embodied in the extracts, was studied as well. Interestingly, oxidation induction times (OIT) for the impregnation of EN with thyme and clove extracts were established to be, respectively, 27.7 and 39.02 min, which are higher than for thymol (18.4 min) and eugenol (21.1 min). Therefore, an aging experiment, mimicking the full spectrum of sunlight, was carried out to investigate the resistance to common radiation of materials impregnated with antioxidative substances. As expected, the experiment revealed that the natural extracts increased the shelf-life of the polymer matrix by inhibiting the degradation processes. The aging resistance was assessed based on detected changes in the materials' behavior and structure that were examined with Fourier-transform infrared spectroscopy, contact angle measurements, color quantification, tensile tests, and hardness investigation. Such broad results of solar aging regarding materials impregnated with thyme and clove extracts have not been reported to date. Moreover, CE was found to be the most effective modifying agent for enabling material with antimicrobial activity against Escherichia coli to be obtained.

Polymeric Microfiltration Membranes Modification by Supercritical Solvent Impregnation-Potential Application in Open Surgical Wound Ventilation

This study investigated supercritical solvent impregnation of polyamide microfiltration membranes with carvacrol and the potential application of the modified membranes in ventilation of open surgical wounds. The impregnation process was conducted in batch mode at a temperature of 40 °C under pressures of 10, 15, and 20 MPa for contact times from 1 to 6 h. FTIR was applied to confirm the presence of carvacrol on the membrane surface. In the next step, the impact of the modification on the membrane structure was studied using scanning electron and ion beam microscopy and cross-filtration tests. Further, the release of carvacrol in carbon dioxide was determined, and finally, an open thoracic cavity model was applied to evaluate the efficiency of carvacrol-loaded membranes in contamination prevention. Carvacrol loadings of up to 43 wt.% were obtained under the selected operating conditions. The swelling effect was detectable. However, its impact on membrane functionality was minor. An average of 18.3 µg of carvacrol was released from membranes per liter of carbon dioxide for the flow of interest. Membranes with 30–34 wt.% carvacrol were efficient in the open thoracic cavity model applied, reducing the contamination levels by 27% compared to insufflation with standard membranes.

Polymeric Carriers Designed for Encapsulation of Essential Oils with Biological Activity

The article reviews the possibilities of encapsulating essential oils EOs, due to their multiple benefits, controlled release, and in order to protect them from environmental conditions. Thus, we present the natural polymers and the synthetic macromolecular chains that are commonly used as networks for embedding EOs, owing to their biodegradability and biocompatibility, interdependent encapsulation methods, and potential applicability of bioactive blend structures. The possibilities of using artificial intelligence to evaluate the bioactivity of EOs—in direct correlation with their chemical constitutions and structures, in order to avoid complex laboratory analyses, to save money and time, and to enhance the final consistency of the products—are also presented.

Functional Modification of Cellulose Acetate Microfiltration Membranes by Supercritical Solvent Impregnation

This study investigates the modification of commercial cellulose acetate microfiltration membranes by supercritical solvent impregnation with thymol to provide them with antibacterial properties. The impregnation process was conducted in a batch mode, and the effect of pressure and processing time on thymol loading was followed. The impact of the modification on the membrane's microstructure was analyzed using scanning electron and ion-beam microscopy, and membranes' functionality was tested in a cross-flow filtration system. The antibiofilm properties of the obtained materials were studied against Staphyloccocus aureus and Pseudomonas aeruginosa, while membranes' blocking in contact with bacteria was examined for S. aureus and Escherichia coli. The results revealed a fast impregnation process with high thymol loadings achievable after just 0.5 h at 15 MPa and 20 MPa. The presence of 20% of thymol provided strong antibiofilm properties against the tested strains without affecting the membrane's functionality. The study showed that these strong antibacterial properties could be implemented to the commercial membranes' defined polymeric structure in a short and environmentally friendly process.

Nano-technological approaches for plant and marine-based polysaccharides for nano-encapsulations and their applications in food industry

Novel food preservation methods, along with preservatives have been employed to prevent food products from spoilage. There is an increasing demand to substitute synthetic preservatives with natural bioactive compounds since they are safe and environmentally friendly. Bioactive compounds with functional and therapeutic properties are found in foods and have also beneficial physiological and immunological health effects. However, there are some issues associated with bioactive compounds, such as low stability, solubility, and permeability. Encapsulation techniques, especially nano-encapsulation, are a promising technique to overcome these restrictions. A range of the plants' constituents can be converted into bio-nanomaterials. Major plant constituents are polysaccharides which have good biocompatibility properties and therapeutic activities, such as antioxidant, antiviral, anti-inflammatory, anti-allergic, and anti-tumor. Among plant and marine-based polysaccharides, cellulose, starch, alginates, chitosan, and carrageenans have been used as carrier materials to preserve core material. Moreover, many studies indicated that favorable sources such as plant and marine based polysaccharides are emerging. This chapter will cover plant and marine-based polysaccharides for nano-encapsulation and their application in the food industry.

Application of Supercritical Solvent Impregnation for Production of Zeolite Modified Starch-Chitosan Polymers with Antibacterial Properties

In the present study, supercritical solvent impregnation (SSI) has been applied to incorporate thymol into bio-composite polymers as a potential active packaging material. Thymol, a natural component with a proven antimicrobial activity, was successfully impregnated into starch-chitosan (SC) and starch-chitosan-zeolite (SCZ) films using supercritical carbon dioxide (scCO₂) as a solvent. Experiments were performed at 35 °C, pressures of 15.5 and 30 MPa, and an impregnation time in the range of 4–24 h. The highest impregnation yields of SC films with starch to chitosan mass ratios of 1:1 and 1:2 were 10.80% and 6.48%, respectively. The addition of natural zeolite (15–60%) significantly increased the loading capacity of films enabling thymol incorporation in a quantity of 16.7–27.3%. FTIR and SEM analyses were applied for the characterization of the films. Mechanical properties and water vapor permeability of films before and after the impregnation were tested as well. Thymol release kinetics in deionized water was followed and modeled by the Korsmeyer-Peppas and Weibull model. SCZ films with thymol loading of approximately 24% exhibited strong antibacterial activity against E. coli and methicillin-resistant Staphylococcus (S.) aureus (MRSA).

Repositioning Natural Antioxidants for Therapeutic Applications in Tissue Engineering

Although a large panel of natural antioxidants demonstrate a protective effect in preventing cellular oxidative stress, their low bioavailability limits therapeutic activity at the targeted injury site. The importance to deliver drug or cells into oxidative microenvironments can be realized with the development of biocompatible redox-modulating materials. The incorporation of antioxidant compounds within implanted biomaterials should be able to retain the antioxidant activity, while also allowing graft survival and tissue recovery. This review summarizes the recent literature reporting the combined role of natural antioxidants with biomaterials. Our review highlights how such functionalization is a promising strategy in tissue engineering to improve the engraftment and promote tissue healing or regeneration.

Recent advances in biodegradable matrices for active ingredient release in crop protection: Towards attaining sustainability in agriculture

Climate changes, emerging species of plant pests, and deficits of clean water and arable land have made availability of food to the ever-increasing global population a challenge. Excessive use of synthetic pesticides to meet ever-increasing production needs has resulted in development of resistance in pest populations, as well as significant ecotoxicity, which has directly and indirectly impacted all life-forms on earth. To meet the goal of providing safe, sufficient, and high-quality food globally with minimal environmental impact, one strategy is to focus on targeted delivery of pesticides using eco-friendly and biodegradable carriers that are derived from naturally available materials. Herein, we discuss some of the recent approaches to use biodegradable matrices in crop protection, while exploring their design and efficiency. We summarize by discussing associated challenges with the existing approaches and future trends that can lead the world to more sustainable agricultural practices.

•

Providing food safety and security is critical for the growing global population.

•

Crop yield is affected by various biotic and abiotic factors.

•

Targeted/sustained delivery of agrochemicals reduces excessive use of pesticides.

•

Nature-derived biodegradable materials curtail plant health and environmental harm.

•

Biodegradable matrices hold promise for sustainable crop protection.

Hierarchical porous nanofibers containing thymol/beta-cyclodextrin: Physico-chemical characterization and potential biomedical applications

As an effective natural antibacterial component, the low water solubility of thymol (THY) has stemmed its potential in biomedical application. Here, β-cyclodextrin (β-CD) and THY were self-assembled to form water-soluble inclusion complex (IC). The successful formation of IC was confirmed via ¹H NMR. As an antibacterial agent, the resultant IC was then incorporated into cellulose acetate (CA) fibrous matrix with hierarchical structure (nanopores on porous fibrous webs) via electrospinning (CA/THY/β-CD), and the pure THY was also encapsulated into CA for comparison (CA/THY). In vitro dissolution tests demonstrated that CA/THY/β-CD fibrous membrane exhibited sustained drug release, which abided by non-Fickian diffusion. Besides, the CA/THY/β-CD fibrous membrane exhibited more effective and long-lasting antibacterial activity against S. aureus. Furthermore, the combination of hierarchical porous structure with sustained drug release endowed the CA/THY/β-CD fibrous membrane with good cytocompatibility. Taken together, the CA/THY/β-CD fibrous membrane could be an attractive candidate for wound dressing material.

Supercritical Fluid Applications in the Design of Novel Antimicrobial Materials

Bacterial resistance to antibiotics is one of the biggest problems in the modern world. The prevention of bacterial spreading from hospitals to the community and vice versa is an issue we have to deal with. This review presents a vast potential of contemporary high-pressure techniques in the design of materials with antimicrobial activity. Scientists from all over the world came up with ideas on how to exploit extraordinary properties of supercritical fluids in the production of advantageous materials in an environmentally friendly way. The review summarizes reported methods and results.

Manuka honey incorporated cellulose acetate nanofibrous mats: Fabrication and in vitro evaluation as a potential wound dressing

Wound dressings are the primary barrier between the wound surface and the outer environment. Here we report the fabrication of cellulose acetate (CA)-Manuka honey (MH) composite nanofibrous mats as a biocompatible and antimicrobial wound dressing. CA mats with different quantities of MH were developed by electrospinning. The ATR-FTIR spectra confirm the inclusion of MH in the composite CA-MH nanofibrous mats. The fibers were continuous and bead-free with acceptable mechanical properties. The fiber diameter increased with an increase in MH content. Inclusion of MH in the electrospun composite CA-MH nanofibrous mats shows high efficacy to prevent bacterial growth on the wound surface. The MH loaded CA nanofiber mats showed good antioxidant abilities, while the ability to free radicalize the DPPH was dependent upon the factors of MH content in the fiber and the time of immersion in the DPPH solution. Besides, the nanofibrous mat's high porosity (85-90%) and WVTR values of 2600 to 1950 g/m²/day, suitable for wound breathability and the mats show high cytocompatibility to NIH 3T3 cell line in in vitro testing, proving to be effective for promoting wound healing.

The role of physicochemical properties in the nanoprecipitation of cellulose acetate

The cellulose acetate (CA) nanoparticles (NPs) were prepared via the nanoprecipitation technique. The effects of solvent mixture quality and order of addition on the size evolution of CA NPs were investigated. The size of CA NPs was reduced by decreasing the nonsolvent-solvent mixture interaction parameter (χ_NS-mS) and by increasing the polymer-solvent mixture interaction parameter (χ_P-mS). The NPs prepared by the method of addition of the polymer solution to the nonsolvent were smaller than those prepared by addition of the nonsolvent to the polymer solution. The very small CA NPs with the diameter of 37 nm and very narrow PdI of 0.045 were fabricated without using any surfactant and charged groups. The role of surface tension and osmotic pressure forces on the formation of NPs were discussed. The formation mechanism of NPs could be assigned to the rapid polymer precipitation and solidification (vitrification) of the nuclei.