A novel electrospun hydroxypropyl methylcellulose/polyethylene oxide blend nanofibers: Morphology and physicochemical properties

Electrospun Cerium Oxide Nanoparticle/Aloe Vera Extract-Loaded Nanofibrous Poly(Ethylene Oxide)/Polyurethane Mats As Diabetic Wound Dressings

Currently the prevalence of diabetic wounds brings a huge encumbrance onto patients, causing high disability and mortality rates and a major medical challenge for society. Therefore, in this study, we are targeting to fabricate aloe vera extract infused biocompatible nanofibrous patches to facilitate the process of diabetic wound healing. Additionally, clindamycin has been adsorbed onto the surface of in-house synthesized ceria nanoparticles and again used separately to design a nanofibrous web, as nanoceria can act as a good drug delivery vehicle and exhibit both antimicrobial and antidiabetic properties. Various physicochemical characteristics such as morphology, porosity, and chemical composition of the produced nanofibrous webs were investigated. Bacterial growth inhibition and antibiofilm studies of the nanofibrous materials confirm its antibacterial and antibiofilm efficacy against Gram-positive and Gram-negative bacteria. An in vitro drug release study confirmed that the nanofibrous mat show a sustained drug release pattern (90% of drug in 96 h). The nanofibrous web containing drug loaded nanoceria not only showed superior in vitro performance but also promoted greater wound contraction (95 ± 2%) in diabetes-induced mice in just 7 days. Consequently, it efficaciously lowers the serum glucose level, inflammatory cytokines, oxidative stress, and hepatotoxicity markers as endorsed by various ex vivo tests. Conclusively, this in-house-fabricated biocompatible nanofibrous patch can act as a potential medicated suppository that can be used for treating diabetic wounds in the proximate future.

Development of Hybrid Electrospun Nanofibers: Improving Effects of Cellulose Nanofibers (CNFs) on Electrospinnability of Gelatin

Cellulose nanofibers (CNFs) were used to improve the electrospinnability of the gelatin protein in a water/ethanol/acetic acid (3:2:3, v/v) solution. The effects of different concentrations of CNFs (0.5-4%) on the important physical properties of the gelatin solution (15%), including rheology, conductivity, and surface tension, were investigated. The apparent viscosity and shear-thinning behavior were increased by increasing the CNF concentration from 0 to 4% at a low shear rate (<10 s-1). CNFs also increased the electrical conductivity and surface tension of the gelatin solution. Scanning electron microscopy (SEM) images revealed uniformly ordered structures with good continuity without fracture or bead formation in all hybrid nanofibers. They also showed that the average diameters of fibers decreased from 216 nm in the pure gelatin nanofibers to 175.39 nm in the hybrid gelatin/CNF (4%) ones. Differential scanning calorimetry (DSC) results showed that CNFs increased Tg, and X-ray diffraction (XRD) analysis showed that the electrospinning process caused the formation of more amorphous structures in the gelatin/CNF hybrid nanofibers. The tensile test indicated that by adding 2% CNFs, the ultimate tensile strength (UTS) and strain at break (SB) of nanofiber mats increased from 4.26 to 10.5 MPa and 3.3% to 6.25%, respectively. The current study indicated that incorporating CNFs at the optimal concentration into a gelatin solution can improve the resulting hybrid nanofibers' morphology, average diameter, and mechanical properties.

Antimicrobial liposomes-in-nanofiber wound dressings prepared by a green and sustainable wire-electrospinning set-up

Increasing prevalence of infected and chronic wounds demands improved therapy options. In this work an electrospun nanofiber dressing with liposomes is suggested, focusing on the dressing's ability to support tissue regeneration and infection control. Chloramphenicol (CAM) was the chosen antibiotic, added to the nanofibers after first embedded in liposomes to maintain a sustained drug release. Nanofibers spun from five different polymer blends were tested, where pectin and polyethylene oxide (PEO) was identified as the most promising polymer blend, showing superior fiber formation and tensile strength. The wire-electrospinning setup (WES) was selected for its pilot-scale features, and water was applied as the only solvent for green electrospinning and to allow direct liposome incorporation. CAM-liposomes were added to Pectin-PEO nanofibers in the next step. Confocal imaging of rhodamine-labelled liposomes indicated intact liposomes in the fibers after electrospinning. This was supported by the observed in vitroCAM-release, showing that Pectin-PEO-nanofibers with CAM-liposomes had a delayed drug release compared to controls. Biological testing confirmed the antimicrobial efficacy of CAM and good biocompatibility of all CAM-nanofibers. The successful fiber formation and green production process with WES gives a promising outlook for industrial upscaling.

Zein and hydroxypropyl methylcellulose acetate succinate microfibers combined with metronidazole benzoate and/or metronidazole-incorporated cellulose nanofibrils for potential periodontal treatment

The development of flexible and porous materials to control antibacterial delivery is a pivotal endeavor in medical science. In this study, we aimed to produce long and defect-free fibers made of zein and hydroxypropyl methylcellulose acetate succinate (HPMCAS) to be used as a platform for the release of metronidazole (MDZ) and metronidazole benzoate (BMDZ) to be potentially used in periodontal treatment. Microfibers prepared via electrospinning under a 2:3 (w/w) zein to HPMCAS ratio, containing 0.5 % (w/w) poly(ethylene oxide) (PEO) and 1 % (w/w) cellulose nanofibril (CNF) were loaded with 40 % (w/w) MDZ, 40 % (w/w) BMDZ, or a combination of 20 % (w/w) of each drug. The addition of CNF improved the electrospinning process, resulting in long fibers with reduced MDZ and BMDZ surface crystallization. MDZ- and BMDZ-incorporated fibers were semicrystalline and displayed commendable compatibility among drugs, nanocellulose and polymeric chains. Release tests showed that zein/HPMCAS/PEO fibers without CNF and with 20 % (w/w) MDZ/ 20 % (w/w) BMDZ released the drug at a slower and more sustained rate compared to other samples over extended periods (up to 5 days), which is a favorable aspect concerning periodontitis treatment.

Resveratrol-loaded octenyl succinic anhydride modified starch emulsions and hydroxypropyl methylcellulose (HPMC) microparticles: Cytotoxicity and antioxidant bioactivity assessment after in vitro digestion

Hydroxypropyl methylcellulose (HPMC)-based microparticles and modified starch emulsions (OSA-MS) were loaded with resveratrol and characterized regarding their physicochemical and thermal properties. Both delivery systems were subject to an in vitro gastrointestinal digestion to assess the bioaccessibility of resveratrol. In addition, cell-based studies were conducted after in vitro digestion and cytotoxicity and oxidative stress were assessed. HPMC-based microparticles displayed higher average sizes (d) and lower polydispersity index (PDI) (d = 948 nm, PDI < 0.2) when compared to OSA-MS-based emulsions (d = 217 nm, PDI < 0.3). Both proved to protect resveratrol under digestive conditions, leading to an increase in bioaccessibility. Resveratrol-loaded HPMC-microparticles showed a higher bioaccessibility (56.7 %) than resveratrol-loaded emulsions (19.7 %). Digested samples were tested in differentiated co-cultures of Caco-2 and HT29-MTX, aiming at assessing cytotoxicity and oxidative stress, and a lack of cytotoxicity was observed for all samples. Results displayed an increasing antioxidant activity, with 1.6-fold and 1.4-fold increases over the antioxidant activity of free resveratrol, for HPMC-microparticles and OSA-MS nanoemulsions, respectively. Our results offer insight into physiological relevancy due to assessment post-digestion and highlight the protection that the use of micro-nano delivery systems can confer to resveratrol and their potential to be used as functional food ingredients capable of providing antioxidant benefits upon consumption.

A novel designed nanofibrous mat based on hydroxypropyl methyl cellulose incorporating mango peel extract for potential use in wound care system

Skin tissue is damaged by factors such as burns, physical injuries and diseases namely diabetes. Infection and non-healing of burn wounds and lack of angiogenesis in diabetic wounds lead to extensive injuries and death. Therefore, the design of wound dressings with antibacterial and restorative capabilities is very important. In this study, nanofibers (NFs) including polyurethane (PU) and hydroxypropyl methyl cellulose (HPMC) were prepared with different ratios and Mango peel extract (MPE) loaded into NFs by electrospinning method. The morphology, chemical structure, porosity, degradation, water vapor permeability, mechanical properties, wettability, antioxidant activity and some cell studies and evaluation of their antibacterial properties were investigated. The optimal mat (PU90/HPMC10) had a defect-free morphology with homogeneous NFs. Furthermore, it showed improved biodegradability, water vapor permeability and porosity compared to other Mats. All NFs were non-toxic with hydrophilic behavior in the cellular environment and had acceptable hemocompatibility. The PU90/HPMC10/20 % optimal scaffold had significantly higher cell viability and proliferation than other samples and also had a higher antibacterial ability against pathogenic bacteria S. aureus (17 mm) and E. coli (11 mm). All these findings confirm that the produced NF mats, especially those loaded with MPE, have a high potential to be used as an effective wound dressing.

Robust Piezoelectric Biomolecular Membranes from Eggshell Protein for Wearable Sensors

Flexible and wearable devices are drawing increasing attention due to their promising applications in energy harvesting and sensing. However, the application of wearable devices still faces great challenges, such as flexibility, repeatability, and biodegradability. Biopiezoelectric materials have been regarded as favorable energy-harvesting sources due to their nontoxicity and biocompatibility. Here, a wearable and biodegradable sensor is proposed to monitor human activities. The proposed sensor is fabricated via a low-cost, facile, and scalable electrospinning technology from nanofibers composed of eggshell membranes mixed with polyethylene oxide. It is shown that the sensor exhibits excellent flexibility, outstanding degradability, and mechanical stability over 3000 cycles under periodic stimulation. The device displays multiple potential applications, including the recognition of different objects, human motion monitoring, and active voice recognition. Finally, it is shown that the composite nanofiber membrane has good degradability and breathability. With excellent sensing performance, environmental friendliness, and ease of processing, the eggshell membrane-based sensor could be a promising candidate for greener and more environmentally friendly devices for application in implantable and wearable electronics.

The reduce of water vapor permeability of polysaccharide-based films in food packaging: A comprehensive review

Polysaccharide-based films are favored in the food packaging industry because of their advantages of green and safe characters, as well as natural degradability, but due to the structural defects of polysaccharides, they also have the disadvantages of high water vapor permeability (WVP), which greatly limits their application in the food packaging industry. To break the limitation, numerous methods, e.g., physical and/or chemical methods, have been employed. This review mainly elaborates the up-to-date research status of the application of polysaccharide-based films (PBFs) in food packaging area, including various films from cellulose and its derivatives, starch, chitosan, pectin, alginate, pullulan and so on, while the methods of reducing the WVP of PBFs, mainly divided into physical and chemical methods, are summarized, as well as the discussions about the existing problems and development trends of PBFs. In the end, suggestions about the future development of WVP of PBFs are presented.

Unleashing the healing potential: Exploring next-generation regenerative protein nanoscaffolds for burn wound recovery

Burn injury is a serious public health problem and scientists are continuously aiming to develop promising biomimetic dressings for effective burn wound management. In this study, a greater efficacy in burn wound healing and the associated mechanisms of α-lactalbumin (ALA) based electrospun nanofibrous scaffolds (ENs) as compared to other regenerative protein scaffolds were established. Bovine serum albumin (BSA), collagen type I (COL), lysozyme (LZM) and ALA were separately blended with poly(ε-caprolactone) (PCL) to fabricate four different composite ENs (LZM/PCL, BSA/PCL, COL/PCL and ALA/PCL ENs). The hydrophilic composite scaffolds exhibited an enhanced wettability and variable mechanical properties. The ALA/PCL ENs demonstrated higher levels of fibroblast proliferation and adhesion than the other composite ENs. As compared to PCL ENs and other composite scaffolds, the ALA/PCL ENs also promoted a better maturity of the regenerative skin tissues and showed a comparable wound healing effect to Collagen spongeⓇ on third-degree burn model. The enhanced wound healing activity of ALA/PCL ENs compared to other ENs could be attributed to their ability to promote serotonin production at wound sites. Collectively, this investigation demonstrated that ALA is a unique protein with a greater potential for burn wound healing as compared to other regenerative proteins when loaded in the nanofibrous scaffolds.

A Stretchable Solid Ionic Electrode-Based Triboelectric Nanogenerator for Biomechanical Energy Harvesting and Self-Powered Sensors

Stretchable power devices and self-powered sensors have become increasingly desired for wearable electronics and artificial intelligence. In this study, an all-solid-state triboelectric nanogenerator (TENG) is reported, whose one solid-state structure prevents delamination during stretch and release cycles and increasing the patch adhesive force (3.5 N) and strain (586% elongation at break). Through the synergetic virtues of stretchability, ionic conductivity, and excellent adhesion to the tribo-layer, reproducible open-circuit voltage (VOC ) of 84 V, charge (QSC ) of 27.5 nC, and short-circuit current (ISC ) of 3.1 µA after drying at 60°C or 20,000 contact-separation cycles are obtained. Apart from contact-separation, this device shows unprecedented electricity generation through stretch-release of solid materials leading to a linear relationship between VOC and strain. For the first time, this work provides a clear explanation of the working mechanism of contact-free stretching-releasing and investigates the relationships of exerted force, strain, thickness of the device, and electric output. Benefitting from the one solid-state structure, this contact-free device remains stable even after repeated stretch-release cycling, maintaining 100% of its VOC after 2500 stretch-release cycles. These findings provide a strategy toward highly conductive and stretchable electrodes for harvesting mechanical energy and health monitoring.

Fabrication of ɛ-Polylysine-Loaded Electrospun Nanofiber Mats from Persian Gum-Poly (Ethylene Oxide) and Evaluation of Their Physicochemical and Antimicrobial Properties

In the present study, electrospun nanofiber mats were fabricated by mixing different ratios (96:4, 95:5, 94:6, 93:7, and 92:8) of Persian gum (PG) and poly (ethylene oxide) (PEO). The SEM micrographs revealed that the nanofibers obtained from 93% PG and 7% PEO were bead-free and uniform. Therefore, it was selected as the optimized ratio of PG:PEO for the development of antimicrobial nanofibers loaded with ɛ-Polylysine (ɛ-PL). All of the spinning solutions showed pseudoplastic behavior and the viscosity decreased by increasing the shear rate. Additionally, the apparent viscosity, G', and G″ of the spinning solutions increased as a function of PEO concentration, and the incorporation of ɛ-PL did not affect these parameters. The electrical conductivity of the solutions decreased when increasing the PEO ratio and with the incorporation of ɛ-PL. The X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectra showed the compatibility of polymers. The antimicrobial activity of nanofibers against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) was investigated, and the samples loaded with ɛ-PL demonstrated stronger antimicrobial activity against S. aureus.

Synthesis and Characterization of a Novel Composite Edible Film Based on Hydroxypropyl Methyl Cellulose Grafted with Gelatin

A novel composite edible film was synthesized by grafting gelatin chain onto hydroxypropyl methyl cellulose (HPMC) in the presence of glycerol (used as a plasticizer) using a solution polymerization technique. The reaction was carried out in homogeneous aqueous medium. Thermal properties, chemical structure, crystallinity, surface morphology, and mechanical and hydrophilic performance changes of HPMC caused by the addition of gelatin were investigated by differential scanning calorimetry, thermogravimetric, Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction, universal testing machine and water contact angle. The results shows that HPMC and gelatin are miscible and the hydrophobic property of the blending film can be enhanced with the introduction of the gelatin. Moreover, the HPMC/gelatin blend films are flexible, and exhibit excellent compatibility, good mechanical properties and also thermal stability, and could be promising candidates for food packaging materials.

pH Effect on the Structure, Rheology, and Electrospinning of Maize Zein

As a simple and convenient technology to fabricate micron-to-nanoscale fibers with controllable structure, electrostatic spinning has produced fiber films with many natural advantages, including a large specific surface area and high porosity. Maize zein, as a major storage protein in corn, showed high hydrophobicity and has been successfully applied as a promising carrier for encapsulation and controlled release in the pharmaceutical and food areas. Proteins exhibit different physical and chemical properties at different pH values, and it is worth investigating whether this change in physical and chemical properties affects the properties of electrospun fiber films. We studied the pH effects on zein solution rheology, fiber morphology, and film properties. Rotational rheometers were used to test the rheology of the solutions and establish a correlation between solution concentration and fiber morphology. The critical concentrations calculated by the cross-equation fitting model were 17.6%, 20.1%, 20.1%, 17.1%, and 19.5% (w/v) for pH 4, 5, 6, 7, and 8, respectively. The secondary structure of zein changed with the variation in solution pH. Furthermore, we analyzed the physical properties of the zein films. The contact angles of the fiber membranes prepared with different pH spinning solutions were all above 100, while zein films formed by solvent evaporation showed hydrophilic properties. The results indicated that the rheological properties of zein solutions and the surface properties of the film were affected by the pH value. This study showed that zein solutions can be stabilized to form electrospun fibers at a variety of pH levels and offered new opportunities to further enhance the encapsulation activity of zein films for bioactive materials.

Cytotoxicity evaluation of poly(ethylene) oxide nanofibre in MCF-7 breast cancer cell line

Biocompatible polymers have received significant interest from researchers for their potential in diagnostic applications. This type of polymer can perform with an appropriate host response or carrier for a specific purpose. The current study aims to fabricate and characterise poly(ethylene) oxide (PEO) nanofibres with different concentrations for cytotoxicity evaluation in human breast cancer cell lines (MCF-7) and to get an optimal PEO nanofibre concentration (permissible limit) as a suitable polymer matrix or carrier with potential use in diagnostic applications. The fabrication of PEO nanofibres was done using electrospinning and was characterised by structure and morphology, surface roughness, chemical bonding and release profiles. The functional effects of PEO nanofibres were evaluated with MTS assay and colony formation assay in MCF-7 cells. The results showed that viscosity plays a vital role in synthesising a polymer solution in electrospinning for producing beadless nanofibrous mats ranging from 4.7 Pa·s to 77.7 Pa·s. As the PEO concentration increases, the nanofibre diameter and thickness will increase, but the surface roughness will be decreased. The average fibre diameter for 5 wt% PEO, 6 wt% PEO and 7 wt% PEO nanofibres were 129 ± 70 nm, 185 ± 55 nm and 192 ± 53 nm, respectively. In addition, the fibre thickness for 4 wt% PEO, 5 wt% PEO, 6 wt% PEO and 7 wt% PEO nanofibres were 269 ± 3 μm, 664 ± 4 μm, 758 ± 7 μm and 1329 ± 44 μm, respectively. Contrarily, the surface roughness for 4 wt% PEO, 5 wt% PEO, 6 wt% PEO and 7 wt% PEO nanofibres were 55.6 ± 9 nm, 42.8 ± 6 nm, 42.7 ± 7 nm and 36.6 ± 1 nm, respectively. PEO nanofibres showed the same burst release pattern and rate due to the same molecular weight of PEO with a stable release rate profile after 15 min. It also demonstrates that the percentage of PEO nanofibre release increased with the increasing PEO concentration due to the fibre diameter and thickness. The findings showed that all PEO nanofibres formulations were non-toxic to MCF-7 cells. It is suggested that 5 wt% PEO nanofibre exhibited non-cytotoxic characteristics by maintaining the cell viability from dose 0-1000 μg/ml and did not induce the number of colonies. Therefore, 5 wt% PEO nanofibre is the optimal nanofibre concentration and was suggested as a suitable base polymer matrix or carrier with potential use for diagnostic purposes. The findings in this study have demonstrated the influence of cell growth and viability, including the effects of PEO nanofibre formulations on cancer progress characteristics to achieve a permissible PEO nanofibre concentration limit that can be a benchmark in medical applications, particularly diagnostic applications.

Graphene Incorporated Electrospun Nanofiber for Electrochemical Sensing and Biomedical Applications: A Critical Review

The extraordinary material graphene arrived in the fields of engineering and science to instigate a material revolution in 2004. Graphene has promptly risen as the super star due to its outstanding properties. Graphene is an allotrope of carbon and is made up of sp²-bonded carbon atoms placed in a two-dimensional honeycomb lattice. Graphite consists of stacked layers of graphene. Due to the distinctive structural features as well as excellent physico-chemical and electrical conductivity, graphene allows remarkable improvement in the performance of electrospun nanofibers (NFs), which results in the enhancement of promising applications in NF-based sensor and biomedical technologies. Electrospinning is an easy, economical, and versatile technology depending on electrostatic repulsion between the surface charges to generate fibers from the extensive list of polymeric and ceramic materials with diameters down to a few nanometers. NFs have emerged as important and attractive platform with outstanding properties for biosensing and biomedical applications, because of their excellent functional features, that include high porosity, high surface area to volume ratio, high catalytic and charge transfer, much better electrical conductivity, controllable nanofiber mat configuration, biocompatibility, and bioresorbability. The inclusion of graphene nanomaterials (GNMs) into NFs is highly desirable. Pre-processing techniques and post-processing techniques to incorporate GNMs into electrospun polymer NFs are precisely discussed. The accomplishment and the utilization of NFs containing GNMs in the electrochemical biosensing pathway for the detection of a broad range biological analytes are discussed. Graphene oxide (GO) has great importance and potential in the biomedical field and can imitate the composition of the extracellular matrix. The oxygen-rich GO is hydrophilic in nature and easily disperses in water, and assists in cell growth, drug delivery, and antimicrobial properties of electrospun nanofiber matrices. NFs containing GO for tissue engineering, drug and gene delivery, wound healing applications, and medical equipment are discussed. NFs containing GO have importance in biomedical applications, which include engineered cardiac patches, instrument coatings, and triboelectric nanogenerators (TENGs) for motion sensing applications. This review deals with graphene-based nanomaterials (GNMs) such as GO incorporated electrospun polymeric NFs for biosensing and biomedical applications, that can bridge the gap between the laboratory facility and industry.

Recent advances in carrageenan-based films for food packaging applications

In order to solve the increasingly serious environmental problems caused by plastic-based packaging, carrageenan-based films are drawing much attentions in food packaging applications, due to low cost, biodegradability, compatibility, and film-forming property. The purpose of this article is to present a comprehensive review of recent developments in carrageenan-based films, including fabrication strategies, physical and chemical properties and novel food packaging applications. Carrageenan can be extracted from red algae mainly by hydrolysis, ultrasonic-assisted and microwave-assisted extraction, and the combination of multiple extraction methods will be future trends in carrageenan extraction methods. Carrageenan can form homogeneous film-forming solutions and fabricate films mainly by direct coating, solvent casting and electrospinning, and mechanism of film formation was discussed in detail. Due to the inherent limitations of the pure carrageenan film, physical and chemical properties of carrageenan films were enhanced by incorporation with other compounds. Therefore, carrageenan-based films can be widely used for extending the shelf life of food and monitoring the food freshness by inhibiting microbial growth, reducing moisture loss and the respiration, etc. This article will provide useful guidelines for further research on carrageenan-based films.

Incorporation of Ethylcellulose Microparticles Containing a Model Drug with a Bitter Taste into Nanofibrous Mats by the Electrospinning Technique—Preliminary Studies

Electrospinning is considered a simple and comprehensive technique to formulate ultrafine fibres by using an electric field. Polymeric nanofibers constitute promising materials in biomedical applications as drug delivery systems. For their preparation, both natural and synthetic polymers are utilised. Owing to the potential use of electrospun nanofibers as an orodispersible drug dosage form, ethylcellulose microparticles containing the antihistamine drug rupatadine fumarate, prepared by the spray drying technique to conceal the drug’s bitter taste, were incorporated into nanofibers. The obtained nanofibrous mats were evaluated for morphology, mechanical strength, disintegration time, the drug solid state and acceptability in terms of taste masking efficiency. Preliminary studies showed that hypromellose used as a single polymer was not a suitable substance for the manufacturing of nanofibers. Therefore, in order to facilitate the obtention of homogeneous nonwovens, different grades of polyethylene oxide (2,000,000–2M-Da and 4,000,000–4M-Da) were added, which improved the quality of the prepared mats. Nanofibers of the most satisfactory quality were obtained from hypromellose (6.5% w/v) and PEO (2M, 0.5% w/v). SEM image analysis has shown that the nanofibers were homogeneous and smooth and possessed a fast disintegration time (below 30 s) and an adequate drug content with a simultaneous taste-masking effect (as indicated by the in vivo and in vitro methods). However, further studies are necessary to refine their mechanical characteristics.

Encapsulation of Caffeic Acid in Carob Bean Flour and Whey Protein-Based Nanofibers via Electrospinning

The purpose of this study was to introduce caffeic acid (CA) into electrospun nanofibers made of carob flour, whey protein concentrate (WPC), and polyethylene oxide (PEO). The effects of WPC concentration (1% and 3%) and CA additions (1% and 10%) on the characteristics of solutions and nanofibers were investigated. The viscosity and electrical conductivity of the solutions were examined to determine characteristics of solutions. Scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analyzer (TGA), differential scanning calorimetry (DSC), water vapor permeability (WVP), and Fourier transform infrared (FTIR) analysis were used to characterize the nanofibers. According to the SEM results, the inclusion of CA into nanofibers resulted in thinner nanofibers. All nanofibers exhibited uniform morphology. CA was efficiently loaded into nanofibers. When CA concentrations were 1% and 10%, loading efficiencies were 76.4% and 94%, respectively. Nanofibers containing 10% CA demonstrated 92.95% antioxidant activity. The results indicate that encapsulating CA into carob flour–WPC-based nanofibers via electrospinning is a suitable method for active packaging applications.

Application of Clove Oil and Sonication Process on the Influence of the Functional Properties of Mung Bean Flour-Based Edible Film

The present study was aimed to investigate the effects of sonication and clove oil incorporation on the improvement of physical, antioxidant, and antimicrobial properties and lipid oxidation inhibiting abilities of mung bean flour (MF)-based films. There were three groups of films tested (1) MF: mung bean flour alone, (2) MFC: MF incorporated with 2% clove oil (C), and (3) MFCU: MFC prepared with sonication (25 kHz, 100% amplitude, 10 min). Film thickness and bulk density showed slight differences, and moisture content, solubility, and water vapor permeability significantly differed between the formulations. Tensile strength, elongation at break, and Young’s modulus were highest for the MFCU films, followed by MFC and MF in rank order. Furthermore, the Fourier-transform infrared spectroscopy results also demonstrated that the clove oil and sonication treatment had improved the interconnections of the biopolymers, thus increasing the physical strength of the film. Phytochemicals in terms of total phenolics and total flavonoids were elevated in the MFCU films and contributed to stronger radical scavenging abilities (p < 0.05). MFC and MFCU films showed a strong antibacterial control of the Gram-positive Staphylococcus aureus (S. aureus) and also of the Gram-negative Campylobacter jejuni (C. jejuni). Overall, the lipid oxidation indicators Thiobarbituric acid reactive substances (TBARS, peroxide value, p-anisidine value, and totox value) showed significantly high inhibition, attributed to radical scavenging activities in the MFCU and MFC samples. The mung bean flour films incorporated with clove oil and prepared with sonication have good potential as packaging materials for food due to strong physical, antimicrobial, and antioxidant properties, as well as lipid oxidation inhibiting abilities.

Hydroxypropyl methylcellulose-based micro- and nanostructures for encapsulation of melanoidins: Effect of electrohydrodynamic processing variables on morphological and physicochemical properties

Electrohydrodynamic processing (EHDP) allows the use of a wide range of biopolymers and solvents, including food-grade biopolymers and green solvents, for the development of micro- and nanostructures. These structures present a high surface-area-to-volume ratio and different shapes and morphologies. The aim of this work was to design and produce hydroxypropyl methylcellulose (HPMC)-based micro- and nanostructures through EHD processing using green solvents, while exploring the influence of process and solution parameters, and incorporating a bioactive extracted from a food by-product. Low (LMW) and high (HMW) molecular weight HPMC have been used as polymers. The design-of-experiments methodology was used to determine the effects of process parameters (polymer concentration, flow rate, tip-to-collector distance, and voltage) of EHDP on the particle and fibre diameter, aspect ratio, diameter distribution, aspect ratio distribution, and percentage of fibre breakage. Additionally, melanoidins extracted from spent coffee grounds were encapsulated into the HPCM-based structures at a concentration of 2.5 mg melanoidins/mL of the polymer solution. Polymer solutions were characterised regarding their viscosity, surface tension and conductivity, and showed that the incorporation of melanoidins increased the viscosity and conductivity values of the polymer solutions. The developed structures were characterised regarding their thermal properties, crystallinity and morphology before and after melanoidin incorporation and it was observed that melanoidin incorporation did not significantly influence the characteristics of the produced micro- and nanostructures. Based on the results, it is possible to envision the use of the produced micro- and nanostructures in a wide range of applications, both in food and biomedical fields.

Antioxidant and Antimicrobial Properties of Mung Bean Phyto-Film Combined with Longkong Pericarp Extract and Sonication

Mung bean (Vigna radiata) flour serves as an excellent biopolymer and a potential material for producing antioxidant and antimicrobial phyto-films. In addition to mung bean flour, this study also combined the longkong (Aglaia dookkoo Griff.) pericarp extract (LPE, 1.5%) and ultrasonication process (0 (C1), 2 (T1), 4 (T2), 6 (T3), 8 (T4), and 10 (T5) min, sonicated at 25 kHz, 100% amplitude) in film emulsion production to improve the antioxidant and antimicrobial efficiency in the phyto-films. This study showed that sonication increased the phyto-films’ color into more lightness and yellowness, and the intensity of the color changes was in accordance with the increased sonication time. Alternatively, the thickness, water vapor permeability, and solubility of the films were adversely affected by extended sonication. In addition, elongation at break and tensile strength increased while the Young modulus decreased in the phyto-films with the extended sonication. Furthermore, the droplet size and polydispersity index of the phyto-films decreased with extended sonication. Conversely, the zeta potential of the film tended to increase with the treatments. Furthermore, phytochemicals such as total phenolic content and total flavonoid contents, and the radical scavenging ability of phyto-films against the DPPH radical, ABTS radical, superoxide radical, hydroxyl radical, and ferrous chelating activity, were significantly higher, and they were steadily increased in the films with the extended sonication time. Furthermore, the phyto-films showed a significant control against Gram (-) pathogens, followed by Gram (+) pathogens. A higher inhibitory effect was noted against L. monocytogens, followed by S. aureus and B. subtilis. Similarly, the phyto-films also significantly inhibited the Gram (-) pathogens, and significant control was noted against C. jejuni, followed by E. coli and P. aeruginosa. Regardless of the mung bean flour, this study found that longkong pericarp extract and the sonication process could also effectively be used in the film emulsions to enhance the efficiency of the antioxidant and antimicrobial properties of phyto-films.

Curcumin polymeric membranes for postoperative peritoneal adhesion: Comparison of nanofiber vs. film and phospholipid-enriched vs. non-enriched formulations

Intra-abdominal adhesion remains a major postoperative problem and is able to place individuals at lifelong risk of serious complications. Among available approaches, insertion of a barrier membrane at the site of injury partially inhibited adhesion formation. Moreover, the local administration of an anti-adhesive agent showed some favorable effects. In this study, we aimed to prepare and fully characterize polycaprolactone (PCL)-based film casts and electrospun nanofibers (NFs) containing a natural anti-inflammatory agent, curcumin (CUR), with extended-release properties. We also compared their efficiencies in preventing tissue adhesions. Additionally, the impact of soy phosphatidylcholine (SPC) enrichment on adhesion prevention was investigated. Prepared membranes were evaluated in terms of surface morphology (SEM, AFM), surface wettability, CUR release profiles, structural properties (FTIR, XRD, DSC), and mechanical behaviors. To further analyze the anti-adhesion effectiveness, a cecal abrasion model was performed on rats. SEM and AFM images showed a smoother surface in SPC-containing films. Concerning NFs, uniform bead-free fibers were observed and SPC containing NFs showed higher conductivity and lower viscosity and therefore, smaller fibers. All formulations exhibited sustained drug release over 4 weeks. In vivo findings revealed the superior performance of films compared to NFs and phospholipid-enriched formulations over non-enriched ones. Among all film formulations and in comparison to the positive control (Seprafilm®), CUR-SPC-PCL films significantly reduced peritoneal adhesions, as evidenced by gross examination, histological evaluation and immunohistochemical (IHC) analysis. The remarkable in vivo anti-adhesion activity together with suitable in vitro properties have made CUR-SPC-PCL films a promising system for postoperative anti-adhesion purposes in the clinic.

Fabrication and characterization of dextran/zein hybrid electrospun fibers with tailored properties for controlled release of curcumin

BACKGROUND

In recent years, there has been considerable interest in the use of biopolymer electrospun nanofibers for various food applications due to the biocompatibility, biodegradability, and high loading capacity. Herein, we fabricated and characterized novel hybrid electrospun fibers from dextran (50%, w/v) and zein (0-30%, w/v) solutions, and the effects of various zein concentrations on the properties of the hybrid electrospun fibers were investigated.

RESULTS

When zein was added at low concentrations (5% and 10%), dextran and zein showed poor miscibility, as reflected by significantly decreased viscosity of the solutions, and the poor mechanical properties of the derived fiber membranes. When zein was added at medium concentrations (15-25%), hydrogen bonds were formed between dextran and zein molecules, as indicated by the red shift of Fourier-transform infrared bands and β-sheet to α-helix structural transformations. The fiber membranes electrospun from a solution with 25% zein showed the most hydrophobic surface, with a water contact angle of 116.9°. The homogenous dispersion of dextran and zein resulted in improved mechanical properties for fibers electrospun from a solution with 30% zein. Curcumin encapsulating dextran/zein electrospun fibers exhibited effective radical scavenging activity and ferric reducing power, along with the desired controlled release behavior for curcumin delivery.

CONCLUSION

Food grade dextran/zein hybrid electrospun fibers demonstrated tunable properties, and appear to be promising as delivery systems for bioactive and edible antimicrobial food packaging. © 2021 Society of Chemical Industry.

Pleurotus eryngii polysaccharide nanofiber containing pomegranate peel polyphenol/chitosan nanoparticles for control of E. coli O157:H7

Pomegranate peel polyphenols (PPP), which are natural, safe, and green antibacterial agents, were introduced and embedded in chitosan to form stable nanoparticles. The PPP@chitosan nanoparticles (PPP@CNPs) were further electrospun into nanofibers based on Pleurotus eryngii polysaccharide (PEP). The preferable distribution of particle size, polydispersity index, and zeta potential was realized through the addition of PPP at 3 mg/mL, which achieved the highest encapsulation rate of 23.71 ± 0.51%. The tensile strength and elongation at break of nanofibers reached 15.76 MPa and 0.69% with the addition of 1% PEP through electrospinning. The results of scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated that the addition of nanoparticles increased the diameter of PEP nanofibers from 148 nm to 163 nm, and the surface roughness of the fibers also increased. Meanwhile, the addition of nanoparticles improved the thermal stability of PEP nanofibers. PPP@CNPs/PEP nanofibers can inhibit the growth of E. coli O157:H7 on pork and cucumber surfaces during the five-days storage, and the inhibition rates were all above 95%. Besides, the nanofibers did not have any impact on the color and texture of foods.

Research progress, models and simulation of electrospinning technology: a review

In recent years, nanomaterials have aroused extensive research interest in the world's material science community. Electrospinning has the advantages of wide range of available raw materials, simple process, small fiber diameter and high porosity. Electrospinning as a nanomaterial preparation technology with obvious advantages has been studied, such as its influencing parameters, physical models and computer simulation. In this review, the influencing parameters, simulation and models of electrospinning technology are summarized. In addition, the progresses in applications of the technology in biomedicine, energy and catalysis are reported. This technology has many applications in many fields, such as electrospun polymers in various aspects of biomedical engineering. The latest achievements in recent years are summarized, and the existing problems and development trends are analyzed and discussed.

Multi-Functional Core-Shell Nanofibers for Wound Healing

Core-shell nanofibers have great potential for bio-medical applications such as wound healing dressings where multiple drugs and growth factors are expected to be delivered at different healing phases. Compared to monoaxial nanofibers, core-shell nanofibers can control the drug release profile easier, providing sustainable and effective drugs and growth factors for wound healing. However, it is challenging to produce core-shell structured nanofibers with a high production rate at low energy consumption. Co-axial centrifugal spinning is an alternative method to address the above limitations to produce core-shell nanofibers effectively. In this study, a co-axial centrifugal spinning device was designed and assembled to produce core-shell nanofibers for controlling the release rate of ibuprofen and hEGF in inflammation and proliferation phases during the wound healing process. Core-shell structured nanofibers were confirmed by TEM. This work demonstrated that the co-axial centrifugal spinning is a high productivity process that can produce materials with a 3D environment mimicking natural tissue scaffold, and the specific drug can be loaded into different layers to control the drug release rate to improve the drug efficiency and promote wound healing.

High-throughput fabrication of silk fibroin/hydroxypropyl methylcellulose (SF/HPMC) nanofibrous scaffolds for skin tissue engineering

Silk fibroin (SF) is a natural macromolecule material with good biocompatibility, which can be used to prepare a variety of biological materials. In this study, hydroxypropyl methylcellulose (HPMC) was applied to improve the properties of SF nanofibrous scaffolds (NFS) for skin tissue engineering applications. SF/HPMC NFS with varying weight ratios of SF: HPMC were prepared in batches by a modified free surface electrospinning. The effects of the varying weight ratio of SF: HPMC on the morphology, property and yield of SF/HPMC NFS were investigated. The results revealed that with the increase of HPMC contents, the hydrophilicity of SF/HPMC NFS would be improved, but the yield of that would decrease. Considering its effects on the morphology, property and yield of SF/HPMC NFS, the optimal weight ratio of SF: HPMC was 7:1. And SF/HPMC NFS with the weight ratio of 7:1 (SF/HPMC-7:1 NFS) had good mechanical property, hydrophilicity, porosity, swelling property and water vapor transmission rate (WVTR). In addition, the viability test results of human umbilical vein endothelial cells demonstrated that SF/HPMC-7:1 NFS maintained excellent biocompatibility for cell adhesion and proliferation.

The Fabrication of Poly(Σ-caprolactone)-Poly(ethylene oxide) Sandwich Type Nanofibers Containing Sericin-Capped Silver Nanoparticles as an Antibacterial Wound Dressing

In this study, antibacterial, synthetic poly(Σ-caprolactone)-poly(ethylene oxide) (PCL-PEO) multilayer nanofibers were produced by an electrospinning method. The material was synthesized in 3 layers. The upper-lower protective layers were produced by PCL nanofibers and the intermediate layer was produced from PEO nanofiber containing sericin-capped silver nanoparticles (S-AgNPs). The electrospinning conditions in which nano-sized, smooth, bead-free fibers were obtained was determined to be an applied voltage of 20 kV, a flow rate of 8 μL/min and a distance between the collector and the needle tip of 22 cm for the PCL layer (dissolved at a 12% g/mL concentration in a chloroform:methanol (3:2) solvent mixture) layer. For the S-AgNPs doped PEO layer (dissolved at a 3.5% g/mL concentration in water), the corresponding conditions were determined to be 20 kV, 15 μL/min and 20 cm. To characterize the three-layer material that consisted of PCL and S-AgNPs doped PEO layers, FTIR and SEM analyses were performed, and the water retention capacity, in situ degradability and antibacterial activity of the material was investigated. According to SEM analysis, the fibers obtained were found to be nano-sized, smooth and bead-free and the average size of the nanofibers forming the PCL layer was 687 nm while the average size of the fibers forming the PEO layer was 98 nm. Antibacterial activity tests were performed using gram-positive (Staphylococcus aureus ATCC 6538) and gram-negative (Escherichia coli ATCC 25922) bacteria and the resulting biomaterial was found to have antimicrobial effect on both gram-negative and gram-positive bacteria. It was determined that the 3-layer material obtained in this study can be used as a wound dressing.

Green Nanotechnology in the Formulation of a Novel Solid Dispersed Multilayered Core-Sheath Raloxifene-Loaded Nanofibrous Buccal Film; In Vitro and In Vivo Characterization

Green nanotechnology utilizes the principles of green chemistry to formulate eco-friendly nanocarrier systems to mitigate patients and environment hazards. Raloxifene (RLX) demonstrates poor aqueous solubility (BCS class II) and low bioavailability, only 2% (extensive first-pass metabolism). The aim of this study is to enhance RLX solubility and bioavailability via development of novel solid dispersed multilayered core-sheath RLX-loaded nanofibers (RLX-NFs) without the involvement of organic solvents. A modified emulsion electrospinning technique was developed. Electrospinning of an RLX-nanoemulsion (RLX-NE) with polymer solution (poly vinyl alcohol (PVA), hydroxypropyl methylcellulose (HPMC), and chitosan (CS) in different volume ratios (1:9, 2:8, and 4:6) using D-optimal response surface methodology was adopted. In vitro characterization of RLX-loaded NFs was performed; scanning electron microscope (SEM), thermal analysis, drug content, release studies, and bioadhesion potential. The optimum NFs formula was evaluated for morphology using high-resolution transmission electron microscopy (HRTEM), and ex vivo drug permeation. The superiority of E2 (comprising RLX-NE and PVA (2:8)) over other NF formulae was statistically observed with respect to Q60 (56.048%), Q240 (94.612%), fiber size (594.678 nm), mucoadhesion time 24 h, flux (5.51 µg/cm2/h), and enhancement ratio (2.12). RLX pharmacokinetics parameters were evaluated in rabbits following buccal application of NF formula E2, relative to RLX oral dispersion. E2 showed significantly higher Cmax (53.18 ± 4.56 ng/mL), and relative bioavailability (≈2.29-fold).

Monitoring freshness of chicken breast by using natural halochromic curcumin loaded chitosan/PEO nanofibers as an intelligent package

Intelligent packaging is important to get information about real time quality of foods. The objective of this study was to develop an electrospun nanofiber halochromic pH sensor film using curcumin, chitosan (CS) and polyethylene oxide (PEO) to monitor chicken freshness. Conductivity and rheological behavior of CS/PEO/curcumin solutions were measured to understand the effect of solution properties on the morphology of the fibers. The morphological characteristics of nanofiber films were investigated by Field Emission Scanning Electron Microscopy (FESEM). Average diameter of the fibers was found to be between 283 ± 27 nm and 338 ± 35 nm. It was concluded that increasing CS amount in nanofibers decreased the diameter of the fibers. Thermal analysis and water vapor permeability features of the pH sensor were also examined. Color changes of curcumin loaded CS/PEO nanofiber film was evaluated on chicken breast package at 4 °C. The color of nanofiber film changed from bright yellow to reddish color which provided an opportunity to detect color changes by even the naked eyes of the untrained consumer. As a quality indicator, surface pH changes of the chicken breast and TVB-N (total volatile basic nitrogen) were measured. At the end of the day 5, pH value of 6.53 ±0.08 and TVB-N concentration of 23.45 ±3.35 mg/100 g indicated that food was at the edge of the acceptance level. As a result, curcumin loaded nanofiber satisfied the expectation and gave an opportunity to visualize real time monitoring of chicken spoilage.

Novel Electrospun Pullulan Fibers Incorporating Hydroxypropyl-β-Cyclodextrin: Morphology and Relation with Rheological Properties

Fibers produced by electrospinning from biocompatible, biodegradable and naturally occurring polymers have potential advantages in drug delivery and biomedical applications because of their unique functionalities. Here, electrospun submicron fibers were produced from mixtures containing an exopolysaccharide (pullulan) and a small molecule with hosting abilities, hydroxypropyl-β-cyclodextrin (HP-β-CD), thus serving as multi-functional blend. The procedure used water as sole solvent and excluded synthetic polymers. Rheological characterization was performed to evaluate the impact of HP-β-CD on pullulan entanglement concentration (CE); the relationship with electrospinnability and fiber morphology was investigated. Neat pullulan solutions required three times CE (~20% w/v pullulan) for effective electrospinning and formation of bead-free nanofibers. HP-β-CD (30% w/v) facilitated electrospinning, leading to the production of continuous, beadless fibers (average diameters: 853-1019 nm) at lower polymer concentrations than those required in neat pullulan systems, without significantly shifting the polymer CE. Rheological, Differential Scanning Calorimetry (DSC) and Dynamic Light Scattering (DLS) measurements suggested that electrospinnability improvement was due to HP-β-CD assisting in pullulan entanglement, probably acting as a crosslinker. Yet, the type of association was not clearly identified. This study shows that blending pullulan with HP-β-CD offers a platform to exploit the inherent properties and advantages of both components in encapsulation applications.

Graphene impregnated electrospun nanofiber sensing materials: a comprehensive overview on bridging laboratory set-up to industry

Owing to the unique structural characteristics as well as outstanding physio-chemical and electrical properties, graphene enables significant enhancement with the performance of electrospun nanofibers, leading to the generation of promising applications in electrospun-mediated sensor technologies. Electrospinning is a simple, cost-effective, and versatile technique relying on electrostatic repulsion between the surface charges to continuously synthesize various scalable assemblies from a wide array of raw materials with diameters down to few nanometers. Recently, electrospun nanocomposites have emerged as promising substrates with a great potential for constructing nanoscale biosensors due to their exceptional functional characteristics such as complex pore structures, high surface area, high catalytic and electron transfer, controllable surface conformation and modification, superior electric conductivity and unique mat structure. This review comprehends graphene-based nanomaterials (GNMs) (graphene, graphene oxide (GO), reduced GO and graphene quantum dots) impregnated electrospun polymer composites for the electro-device developments, which bridges the laboratory set-up to the industry. Different techniques in the base polymers (pre-processing methods) and surface modification methods (post-processing methods) to impregnate GNMs within electrospun polymer nanofibers are critically discussed. The performance and the usage as the electrochemical biosensors for the detection of wide range analytes are further elaborated. This overview catches a great interest and inspires various new opportunities across a wide range of disciplines and designs of miniaturized point-of-care devices.

Electrospun nanofibers: A nanotechnological approach for drug delivery and dissolution optimization in poorly water-soluble drugs

Electrospinning is a novel and sophisticated technique for the production of nanofibers with high surface area, extreme porous structure, small pore size, and surface morphologies that make them suitable for biomedical and bioengineering applications, which can provide solutions to current drug delivery issues of poorly water-soluble drugs. Electrospun nanofibers can be obtained through different methods asides from the conventional one, such as coaxial, multi-jet, side by side, emulsion, and melt electrospinning. In general, the application of an electric potential to a polymer solution causes a charged liquid jet that moves downfield to an oppositely charged collector, where the nanofibers are deposited. Plenty of polymers that differ in their origin, degradation character and water affinity are used during the process. Physicochemical properties of the drug, polymer(s), and solvent systems need to be addressed to guarantee successful manufacturing. Therefore, this review summarizes the recent progress in electrospun nanofibers for their use as a nanotechnological tool for dissolution optimization and drug delivery systems for poorly water-soluble drugs.

Hypromellose - A traditional pharmaceutical excipient with modern applications in oral and oromucosal drug delivery

Hydroxypropylmethylcellulose (HPMC), also known as Hypromellose, is a traditional pharmaceutical excipient widely exploited in oral sustained drug release matrix systems. The choice of numerous viscosity grades and molecular weights available from different manufacturers provides a great variability in its physical-chemical properties and is a basis for its broad successful application in pharmaceutical research, development, and manufacturing. The excellent mucoadhesive properties of HPMC predetermine its use in oromucosal delivery systems including mucoadhesive tablets and films. HPMC also possesses desirable properties for formulating amorphous solid dispersions increasing the oral bioavailability of poorly soluble drugs. Printability and electrospinnability of HPMC are promising features for its application in 3D printed drug products and nanofiber-based drug delivery systems. Nanoparticle-based formulations are extensively explored as antigen and protein carriers for the formulation of oral vaccines, and oral delivery of biologicals including insulin, respectively. HPMC, being a traditional pharmaceutical excipient, has an irreplaceable role in the development of new pharmaceutical technologies, and new drug products leading to continuous manufacturing processes, and personalized medicine. This review firstly provides information on the physical-chemical properties of HPMC and a comprehensive overview of its application in traditional oral drug formulations. Secondly, this review focuses on the application of HPMC in modern pharmaceutical technologies including spray drying, hot-melt extrusion, 3D printing, nanoprecipitation and electrospinning leading to the formulation of printlets, nanoparticle-, microparticle-, and nanofiber-based delivery systems for oral and oromucosal application. Hypromellose is an excellent excipient for formulation of classical dosage forms and advanced drug delivery systems. New methods of hypromellose processing include spray draying, hot-melt extrusion, 3D printing, and electrospinning.