Water-soluble carboxymethylchitosan used as corrosion inhibitor for carbon steel in saline medium

Use of a natural rock material as a precursor to inhibit corrosion of Ti alloy in an aggressive phosphoric acid medium

The mechanism of interaction between magnesite mineral and phosphoric acid (0.001-0.5 M) in addition to the determination of the protective properties for Ti alloy (working electrode) in phosphoric acid both with and without an inhibitor have been investigated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. Results of electrochemical tests show that the corrosion resistance of titanium alloy in phosphoric acid solution only increased and hydrogen production decreased by either decreasing acid concentration or increasing immersion time associated with the thickening of the oxide film formed on the alloy surface. On adding magnesite, the corrosion resistance of Ti alloy is enhanced by increasing the phosphoric acid concentration (0.001-0.5 M) due to the formation of sparingly soluble magnesium phosphate film on the alloy surface that inhibits the effect of increasing hydrogen evolution reaction due to the pH value decreases. The increasing adsorption behavior of the magnesite inhibitor and decreasing its diffusion were deduced from EIS measurements. Thus, the addition of 3% magnesite minimizes the corrosion by forming a new protective film (Mg3(PO4)2), which differs from the traditional passive film and prevents the effect of the increase of hydrogen evolution. The surface morphology and chemical composition of the tested alloy were determined using scanning electron microscopy (SEM), Fourier transform Infra-Red spectroscopy (FTIR), X-ray diffraction (XRD), X-ray Fluorescence (XRF) and In situ Raman spectroscopy.

Konjac glucomannan/carboxymethyl chitosan film embedding gliadin/casein nanoparticles for grape preservation

Constructing biopolymer-based packaging films with fantastic water resistance and mechanical properties for food preservation is highly desirable and challenging. In this work, Gliadin/Casein nanoparticles (GCNPs) were prepared by pH-driven method and embedded into konjac glucomannan/carboxymethyl chitosan (KC) film matrix to improve the water resistance and mechanical properties of KC film. Gliadin and Casein showed good compatibility and co-assembled to form compact GCNPs clusters through hydrogen bonding and hydrophobic interaction verified by FT-IR spectroscopy, and fluorescence spectroscopy. The particle size and zeta potential of GCNPs was 269.7 nm and -7.6 mV, respectively. The effect of GCNPs on the mechanics, water barrier, thermal stability, and UV-shielding of KC-GCNPs film was investigated. SEM images revealed that GCNPs uniformly distributed into KC film matrix and significantly improved the mechanics (tensile strength: 75.6 MPa, elongation at breaking: 36.7 %), water barrier ability (water contact angle: 91.3°, water vapor permeability: 0.994 g mm/m2 day kPa, water solubility: 52.0 %), thermal stability and UV blocking property of KC-GCNPs film. Furthermore, KC-GCNPs film could also be applied to extend the shelf life of grapes. This paper demonstrated the great potential of GCNPs as functional nanofillers in enhancing the physicochemical properties of KC film.

Polymeric surfactants as ideal substitutes for sustainable corrosion protection: A perspective on colloidal and interface properties

Surfactants are well known for their colloidal and corrosion inhibition potential (CIP) due to their strong propensity to interact with metallic surfaces. However, because of their small molecular size and the fact that they are only effective at relatively high concentrations, their application in aqueous phase corrosion inhibition is often restricted. Polymeric surfactants, a unique class of corrosion inhibitors, hold the potential to eradicate the challenges associated with using surfactants in corrosion inhibition. They strongly bond with the metallic surface and offer superior CIP because of their macromolecular polymeric structure and abundance of polar functional groups. In contrast to conventional polymeric corrosion inhibitors, the inclusion of polar functional groups also aids in their solubilization in the majority of popular industry-based electrolytes. Some of the major functional groups present in polymeric surfactants used in corrosion mitigation include O (ether), glycidyl (cyclic ether), -CONH2 (amide), -COOR (ester), -SO3H (sulfonic acid), -COOH (carboxyl), -NH2 (amino), - + NR3/- + NHR2/- + NH2R/- + NH3 (quaternary ammonium), -OH (hydroxyl), -CH2OH (hydroxymethyl), etc. The current viewpoint offers state-of-the-art information on polymer surfactants as newly developing ideal alternatives for conventional corrosion inhibitors. The industrial scale-up, colloidal, coordination, adsorption properties, and structural requirements of polymer surfactants have also been established based on the knowledge obtained from the literature. Finally, the challenges, drawbacks, and potential benefits of using polymer surfactants have also been discussed.

Experimental and theoretical studies for corrosion of molybdenum electrode using streptomycin drug in phosphoric acid medium

Corrosion inhibition of molybdenum electrode in H₃PO₄ acid medium of different concentrations (3.0 to 13 M) has been investigated utilizing different electrochemical techniques. It was observed that the most corrosive concentration is 3.0 M orthophosphoric acid concentration. The effect of adding Cl^- to 3.0 M orthophosphoric acid in the concentration range of 0.1 to 1.0 M was also studied. This study showed that the most corrosive medium is 3.0 M containing 1.0 M chloride ion with the greatest rate of hydrogen production. In 3.0 M H₃PO₄ acid with 1.0 M of NaCl, the tested electrode's corrosion and hydrogen production may be successfully suppressed by adding Streptomycin of 10 mM concentration leading to high inhibition efficiency. The outcomes of the studies were confirmed by scanning electron microscopic examination. Additionally, a computational chemistry approach was used to investigate how streptomycin adsorbs and inhibits corrosion at the interface of metal surfaces, and the outcomes of the computational studies are in excellent accord with the experimental findings.

Green and sustainable chitosan-gum Arabic nanocomposites as efficient anticorrosive coatings for mild steel in saline media

The application of green and sustainable anticorrosive coatings is becoming of upsurge interest for the protection of metallic materials in aggressive environments. Herein, a stable crystalline chitosan/gum Arabic composite (CGAC) nanopowder was successfully synthesized and characterized by various methods. The CGAC nanopowder with different doses (25, 50, 100, and 200 ppm) was used to coat mild steel samples and examined its anticorrosion ability in 3.5 wt.% NaCl solution using gravimetric, electrochemical measurements, and surface characterization techniques. All methods yielded consistent results revealing that nanocomposite coatings can impart good anticorrosive properties to the steel substrate. The obtained protection efficiency was enhanced with increasing CGAC dose in the applied surface layer achieving 96.6% for the 200 ppm-coating. SEM and AFM surface morphologies of uncoated and coated samples after the inundation in the saline solution showed that CGAC coating can block the active corrosive sites on the steel surface, and prevent the aggressive Cl^- ions from attacking the metallic substrate. The water droplet contact angle gave further support as it increased from 50.7° for the pristine uncoated surface to 101.2° for the coated one. The current research demonstrates a promising natural and reliable nanocomposite coating for protecting mild steel structures in the marine environment.

Carbon Fiber/PLA Recycled Composite

Due exceptional properties such as its high-temperature resistance, mechanical characteristics, and relatively lower price, the demand for carbon fiber has been increasing over the past years. The widespread use of carbon-fiber-reinforced polymers or plastics (CFRP) has attracted many industries. However, on the other hand, the increasing demand for carbon fibers has created a waste recycling problem that must be overcome. In this context, increasing plastic waste from the new 3D printing technology has been increased, contributing to a greater need for recycling efforts. This research aims to produce a recycled composite made from different carbon fiber leftover resources to reinforce the increasing waste of Polylactic acid (PLA) as a promising solution to the growing demand for both materials. Two types of leftover carbon fiber waste from domestic industries are handled: carbon fiber waste (CF) and carbon fiber-reinforced composite (CFRP). Two strategies are adopted to produce the recycled composite material, mixing PLA waste with CF one time and with CFRP the second time. The recycled composites are tested under tensile test conditions to investigate the impact of the waste carbon reinforcement on PLA properties. Additionally, thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier-transformed infrared spectroscopy (FTIR) is carried out on composites to study their thermal properties.

Aspartame as a Green and Effective Corrosion Inhibitor for T95 Carbon Steel in 15 wt.% HCl Solution

Oil well acidizing, although a stimulation process, induces the corrosion of metallic equipment and well tubing. There is, at present, a high demand for effective and less toxic high-temperature corrosion inhibitors for the acidizing process due to the failing of the existing inhibitors at high temperatures occasioned by increases in the well depths. In this study, aspartame (ASP), a commercially available natural compound, is examined as a corrosion inhibitor for T95 carbon steel in 15 wt.% HCl solution at 60, 70, 80, and 90 °C using the weight loss, electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), scanning electron microscope (SEM), energy dispersive spectroscopy (EDX), and optical profilometry (OP) techniques. It was found that ASP possesses a corrosion inhibiting effect at the studied conditions. Inhibition efficiency increased with increases in temperature. With 2000 ppm ASP, inhibition efficiency of 86% was achieved from the weight loss method at 90 °C after 4 h of immersion. Results from the electrochemical techniques are in good agreement with the weight loss results. PDP results reveal that ASP acted as a mixed-type corrosion inhibitor under the investigated conditions. The inhibition ability of ASP is due to adsorption on the steel surface and has been confirmed by the SEM, OP, and EDX results. ASP is a promising active compound for the formulation of acidizing corrosion inhibitors.

Control of chloride ion corrosion by MgAlOx/MgAlFeOx in the process of chloride deicing

Adding a corrosion inhibitor to the chloride deicing salt can prevent the corrosion and pollution of Cl^-, which is very important. Layered double hydroxide (LDHs), calcined at high temperature is used as adsorbents to remove various anionic contaminants, and it can reduce the freezing point of solution after adsorbing anions. Therefore, this paper reports the use of calcined LDHs as corrosion inhibitors in deicing salts, which are denoted as MgAlO_x or MgAlFeO_x depending on the preparation element. By analyzing the removal efficiency and the freezing point of MgAlO_x and MgAlFeO_x to Cl^-, the feasibility of the study was determined. Resulted that the removal efficiency to Cl^- of MgAlFeO_x at low temperature (0 ± 2 °C) and room temperature (25 ± 2 °C) was higher than that of MgAlO_x, reaching 39.4% and 85.60%, respectively. And the freezing point of MgAlFeO_x was lower than that of MgAlO_x, the value was -12.0 °C. At the same time, we also found that CaCl₂-MgAlO_x and CaCl₂-MgAlFeO_x significantly reduced the corrosion of carbon steel and concrete compared with chloride salts, and CaCl₂-MgAlFeO_x had the lowest corrosion degree. Hence, MgAlFeO_x was chosen as the corrosion inhibitor in chloride deicing salt. The metal molar ratio, synthesis temperature, and calcination temperature for preparation of MgAl/MgAlFe-LDHs were determined by XRD and TG-DSC analysis that were 9/2/1, 120 °C, and 500 °C, respectively. Characterization methods such as Zeta, XRD, XPS, BET, and SEM were used to study in detail the characteristic changes of MgAlFe-LDHs and MgAlFeO_x after Fe³⁺ was added, and the mechanism of corrosion inhibitors was further determined that was achieved by adsorption and neutralization.

Na2SnO3 functions as outstanding magnesium alloy passivator by synergistic effect with trace carboxymethyl chitosan for Mg–air batteries for standby protection

Coordination of Na2SnO3 with trace carboxymethyl chitosan contributes to standby protection and high utilization efficiency of the AZ61 anode.

Synthesis of 1,8-Naphthyridines by the Ionic Liquid-Catalyzed Friedlander Reaction and Application in Corrosion Inhibition

A several of basic ionic liquids (ILs) were synthesized as green solvents and catalysts for the preparation of 1,8-naphthyridyl derivatives via the Friedlander reaction. [Bmmim][Im] exhibited remarkable catalytic activity to achieve the synthetic targets, and the reaction conditions were optimized. The model product 2,3-diphenyl-1,8-naphthyridine (1,8-Nap), with carboxyethylthiosuccinic acid (CETSA) to form an IL corrosion inhibitor ([1,8-Nap][CETSA]), and its corrosion inhibition performance for Q235 steel in 1 M HCl were researched by weight loss measurements, and the results showed that the inhibition efficiency was 96.95% when the concentration of [1,8-Nap][CETSA] was 1 mM at 35 °C. The electrochemical test verified that [1,8-Nap][CETSA] acted as a mixed-type inhibitor but mainly exhibited cathodic behavior. The inhibitor adsorbed on the metal surface was further proved by surface topography analysis.

The inhibition performance of a novel benzenesulfonamide-based benzoxazine compound in the corrosion of X60 carbon steel in an acidizing environment

The inhibition performance of a novel benzenesulfonamide-based benzoxazine compound in the corrosion of X60 carbon steel an acidizing environment has been examined including some highly electronegative atoms.

Construction of a sustainable/controlled-release nano-container of non-toxic corrosion inhibitors for the water-based siliconized film: Estimating the host-guest interactions/desorption of inclusion complexes of cerium acetylacetonate (CeA) with beta-cyclodextrin (β-CD) via detailed electronic/atomic-scale computer modeling and experimental methods

Utilization of the coatings with self-healing anti-corrosion activities is one of the most promising routes for the development of advanced anti-corrosion coatings. In the present work, the green/sustainable corrosion inhibitive compounds based on the cerium acetylacetonate (CeA) was loaded into a beta-cyclodextrin (β-CD) nano-container (with negligible hazardous impacts) and through combined computer modeling and experimental approaches, the host-guest interactions/desorptions of the inclusion complexes of CeA with beta-cyclodextrin (β-CD) were assessed. The inhibition performance of the β-CD-CeA inclusion complex was investigated by electrochemical and surface experiments in a saline solution (NaCl, 3.5 wt.%). The particles were analyzed by Raman, XRD, FT-IR, and UV-vis spectroscopies. Additionally, the thermal properties in the 30-600 °C temperature range were examined by employing TGA/DTG test, and via the ICP analysis, the concentration of the released inorganic compounds in the electrolyte was studied. Achievements demonstrated 24 ppm Ce element existence after introducing β-CD-CeA inclusion complexes (during 24 h) in NaCl 3.5 wt.% solution. The analysis of Tafel curves proved that the prepared β-CD-CeA inclusion complex could inhibit the metallic substrate corrosion following the mixed cathodic and anodic mechanisms. The EIS investigation disclosed about 82 % inhibition degree after 48 h of metal immersion in the solution containing β-CD-CeA extract. The EIS analysis clarified that the silane coating (SC) resistance was enhanced noticeably by introducing the β-CD-CeA particles into the SC matrix. Using detailed-level (i.e., electronic and atomic) computer modeling techniques applying density functional theory (DFT), Mote Carlo (MC) and molecular dynamics (MD), the active sites, and the adsorption propensity of CeA complexes over the steel-based metallic adsorbents were explored. These modelings evidenced the CeA complexes interfacial adsorption on the steel.

Electrophoretic deposition and characterization of chitosan-molybdenum composite coatings

In this paper, the effect of the electric field on the properties of a new chitosan-molybdenum (Chit-Mo) composite coating obtained by electrophoretic deposition (EPD) was investigated. The composite coatings obtained showed different morphologies depending on the conditions used during the deposition process. Chemical composition results and microstructure analysis showed homogeneous distribution of molybdenum in a chitosan matrix. Corrosion test results showed that the Chit-Mo composite coatings can increase corrosion resistance of 1020 steel in NaCl medium (3.5 %). The coatings obtained at 5 V, pH 5.5, and using a low concentration of reagents (suspension 1: chitosan 0.5 g/L and 1 mM sodium molybdate) reached an inhibition efficiency of up to 76.7 %. Therefore, the results obtained in this work prove the achievement of a new class of chitosan-based composite materials with potential application in the protection of metal structures against corrosion.

Synthesis of carboxymethyl chitosan-functionalized graphene nanomaterial for anticorrosive reinforcement of waterborne epoxy coating

In this study, a carboxymethyl chitosan functionalized graphene (CMCS-rGO) nanomaterial was successfully synthesized in aqueous solution by non-covalent functionalization method. Fourier transform infrared, Raman, ultraviolet visible spectroscopy and thermogravimetric analysis confirmed that carboxymethyl chitosan had been successfully anchored on the surface of graphene. In addition, the CMCS-rGO was used as an anticorrosive nanofiller to be added to waterborne epoxy (EP) coatings to protect steel substrates. The corrosion protection behavior of all coatings was tested by electrochemical workstation, and the results proved that the incorporation of well-dispersed CMCS-rGO nanomaterials could significantly improve the anti-corrosion performance of waterborne epoxy coatings. Furthermore, even after 180 days of immersion, the impedance modulus value of the 0.2 % CMCS-rGO/EP at |Z|_f =0.01 Hz was still approximately 2 orders of magnitude higher than that of the EP.

Efficiency of Steel Corrosion Inhibitors in an Environment of Ethanol-Gasoline Blends

Ethanol produced from renewable sources (i.e., bioethanol) is a first-generation biofuel that is currently being added as a biocomponent into gasolines. Mixtures of ethanol and gasoline are designated as ethanol-gasoline blends (EGBs). Ethanol has high polarity and moisture affinity, which considerably influence the properties of the resulting EGBs including their aggressiveness to many metallic and nonmetallic materials. The corrosion aggressiveness of EGBs can be minimized by suitable corrosion inhibitors. In this study, we tested three different corrosion inhibitors on mild steel in the environment of aggressive E10, E25, E60, and E85 fuels. The inhibitors tested were diethylene triamine (DETA) and two mixed inhibitors containing propargyl alcohol, dibenzyl sulfoxide, and octadecyl amine. To study the efficiency of the corrosion inhibitors, we used static and dynamic corrosion tests and electrochemical measurements including impedance spectroscopy and potentiodynamic polarization. The highest corrosion aggressiveness on mild steel was observed for the E60 fuel. The highest inhibitory efficiency was, for all the fuels tested, observed for the DETA inhibitor. For the DETA concentration of 100 mg·L^-1, the inhibitory efficiency in the E60 fuel was determined to be around 98%.

Hexamethylene-1,6-bis(N-d-glucopyranosylamine) as a novel corrosion inhibitor for oil and gas industry: electrochemical and computational analysis

Experimental and theoretical studies on hexamethylene-1,6-bis(N-d-glucopyranosylamine) as a novel inhibitor against sweet corrosion useful for oil and gas industry.