Self-assembled chitosan-zirconium phosphate nanostructures for adsorption of chromium and degradation of dyes

Renewable-based treatment solution of Reactive Blue 21 dye on fly ash as low-cost and sustainable adsorbent

This study investigated the removal of Reactive Blue 21 (RB 21) dye from aqueous solutions by adsorption, evaluating the waste fly ash (FA). The effects of the parameters, such as initial dye concentration (100-750 mg/L), initial pH (2.0-8.0), adsorbent dose (1.0-4.0 g/L), and temperature (298-323 K) on the adsorption process were investigated. The optimum initial pH value was 2.0 for the highest RB21 dye removal (75.2 mg/g). At optimized conditions (pH 2.0, an adsorbent dosage of 1.0 g/L, a dye concentration of 750 mg/L, and an equilibrium time of 72 h), the highest adsorption capacity was found to be 105.2 mg/g. Moreover, the results of the kinetic studies fitted the pseudo-second-order kinetic model. Equilibrium data were best represented by the Langmuir isotherm model, with a maximum monolayer adsorption capacity of 103.41 mg/g at 323 K. ΔGads0 values were negative and varied from 11.64 to 9.50 kJ/mol in the temperature range of 298-323 K, the values of enthalpy (ΔHadso) and entropy (ΔSadso) of thermodynamics parameters were calculated as 37.62 kJ/mol and 86.67 J/mol K, respectively, indicating that this process was endothermic. Furthermore, the adsorbent costs for powdered activated carbon (PAC) and FA to remove 1 kg of RB 21 dye from aqueous solutions are calculated as 2.52 U.S. $ and 0.34 U.S. $, respectively. It is seen that the cost of FA is approximately 7.4 times lower than PAC. The results showed that FA, a low-cost industrial waste, was promising for the adsorption of RB 21 from aqueous solutions.

The effects of nano-silver loaded zirconium phosphate on antibacterial properties, mechanical properties and biosafety of room temperature curing PMMA materials

Polymethyl methacrylate (PMMA) frequently features in dental restorative materials due to its favorable properties. However, its surface exhibits a propensity for bacterial colonization, and the material can fracture under masticatory pressure. This study incorporated commercially available RHA-1F-II nano-silver loaded zirconium phosphate (Ag-ZrP) into room-temperature cured PMMA at varying mass fractions. Various methods were employed to characterize Ag-ZrP. Subsequently, an examination of the effects of Ag-ZrP on the antimicrobial properties, biosafety, and mechanical properties of PMMA materials was conducted. The results indicated that the antibacterial rate against Streptococcus mutans was enhanced at Ag-ZrP additions of 0%wt, 0.5%wt, 1.0%wt, 1.5%wt, 2.0%wt, 2.5%wt, and 3.0%wt, achieving respective rates of 53.53%, 67.08%, 83.23%, 93.38%, 95.85%, and 98.00%. Similarly, the antibacterial rate against Escherichia coli registered at 31.62%, 50.14%, 64.00%, 75.09%, 86.30%, 92.98%. When Ag-ZrP was introduced at amounts ranging from 1.0% to 1.5%, PMMA materials exhibited peak mechanical properties. However, mechanical strength diminished beyond additions of 2.5%wt to 3.0%wt, relative to the 0%wt group, while PMMA demonstrated no notable cytotoxicity below a 3.0%wt dosage. Thus, it is inferred that optimal antimicrobial and mechanical properties of PMMA materials are achieved with nano-Ag-ZrP (RHA-1F-II) additions of 1.5%wt to 2.0%wt, without eliciting cytotoxicity.

Composite beads from chitosan and zeolitic imidazolate framework-8 for the adsorption and photocatalytic degradation of reactive red 141

This study describes the fabrication of composite beads comprising chitosan and zeolitic imidazolate framework-8 (ZIF-8) as a natural biodegradable dye adsorbent and support for ZnO photocatalyst. Chitosan beads were cross-linked with trisodium citrate dihydrate to enhance the adsorption capacity for the reactive red 141 dye (RR141). The ability was further improved by adding ZIF-8. The optimum loading was 2.5%, and the adsorption equilibrium was reached within 2 h. The maximum adsorption capacity of the composite beads was 6.51 mg g^-1 at pH 4 when an initial concentration of 1000 mg L^-1 was used. The pseudo-second-order kinetics model and the Langmuir isotherm model best described the adsorption process. The composite beads could also adsorb dyes like reactive black, Congo red, direct yellow, reactive orange, rhodamine B, crystal violet, and methylene blue (MB). Thermal stability was significantly improved after coating the surface of the 2.5% ZIF beads with a ZnO photocatalyst. After UV irradiation for 5 h, the photocatalytic beads containing 2.59 weight percent of ZnO could decolorize 99% of MB and 90% of RR141 dyes with a degradation rate of 0.6032 h^-1 and 0.3198 h^-1, respectively. Furthermore, the photocatalytic beads remained effective for at least ten consecutive cycles.

Synergetic Effect of α-ZrP Nanosheets and Nitrogen-Based Flame Retardants on Thermoplastic Polyurethane

A supramolecular self-assembly method was used to prepare melamine cyanurate/α-ZrP nanosheets (MCA@α-ZrP) as a novel hybrid flame retardant for thermoplastic polyurethane (TPU). Microstructure characterization showed a uniform dispersion with strong interfacial strength of the MCA@α-ZrP hybrid within the TPU matrix, leading to simultaneous enhancements in both mechanical and fire-safety properties. The TPU/MCA@α-ZrP nanocomposite exhibited 43.1 and 47.0% increments in tensile strength and fracture energy, respectively. Thanks to the platelike structure of α-ZrP coupled with the dilution effect of MCA (releasing nonflammable gases), the hybrid MCA@α-ZrP reduced the peak heat release rate of TPU by 49.7% in comparison with 15.8 and 35.4% for TPU/MCA and TPU/ α-ZrP composites, respectively. The fire performance index of TPU is significantly promoted by 90% upon adding the MCA@α-ZrP hybrid. Additionally, LOI and UL-94 tests showed high flame-retarding characteristics for the MCA@α-ZrP hybrid. For example, LOI increased from 20.0% for neat TPU to 25.5% for the MCA@α-ZrP hybrid system, and it was rated V-1 from the UL-94 test. Furthermore, the smoke production and pyrolysis products were significantly suppressed by adding the MCA@α-ZrP hybrid into TPU. Interfacial hydrogen bonding, the dilution effect of MCA, forming a "labyrinth" layer, and catalytic action of α-ZrP nanosheets synergistically improved both the mechanical performance and flame retardancy of TPU nanocomposites. This work provides a new example of integrating traditional flame retardants with functional nanosheets to develop polymeric nanocomposites with high mechanical and fire-safety properties.

Zirconia-based nanomaterials: recent developments in synthesis and applications

In the last decade, the whole scientific community has witnessed great advances and progress in the various fields of nanoscience. Among the different nanomaterials, zirconia nanomaterials have found numerous applications as nanocatalysts, nanosensors, adsorbents, etc. Additionally, their exceptional biomedical applications in dentistry and drug delivery, and interesting biological properties, viz. anti-microbial, antioxidant, and anti-cancer activity, have further motivated the researchers to explore their physico-chemical properties using different synthetic pathways. With such an interest in zirconia-based nanomaterials, the present review focuses systematically on different synthesis approaches and their impact on the structure, size, shape, and morphology of these nanomaterials. Broadly, there are two approaches, viz., chemical synthesis which includes hydrothermal, solvothermal, sol-gel, microwave, solution combustion, and co-precipitation methods, and a greener approach which employs bacteria, fungus, and plant parts for the preparation of zirconia nanoparticles. In this review article, the aforementioned methods have been critically analyzed for obtaining specific phases and shapes. The review also incorporates a detailed survey of the applications of zirconia-based nanomaterials. Furthermore, the influence of specific phases, morphology, and the comparison with their counterpart composites for different applications have also been included. Finally, the concluding remarks, prospects and possible scope are given in the last section.

Layered Molybdenum (Meta)phosphate for Photoreduction of Hexavalent Chromium and Degradation of Methylene Blue under Sunlight Radiance

Noble metal, semiconductor, or metal-free nanomaterials have shown promising applicability as potential photocatalyst materials. A one-step process has been established for the synthesis of layered molybdenum (meta)phosphate [MoO₂(PO₃)₂] using a solvothermal method. The nanopowders were characterized by X-ray diffraction (XRD), UV-visible spectroscopy (UV-vis), scanning electron microscopy (SEM), infrared spectroscopy (IR), X-ray photoelectron spectroscopy (XPS), photoluminescence spectroscopy (PL), surface area analysis (Brunauer-Emmett-Teller (BET)), electron spin resonance (ESR), and high-resolution transmission electron microscopy (HRTEM). Through this study, we demonstrate the use of MoO₂(PO₃)₂ as a photocatalyst for wastewater treatment. The photoreduction of toxic Cr⁶⁺ to Cr³⁺ by layered molybdenum (meta)phosphate is investigated using formic acid as a scavenger. This catalyst has also been used for photodegrading organic dyes like methylene blue. MoO₂(PO₃)₂ has been shown to complete photoreduction of toxic Cr⁶⁺ to Cr³⁺ in 6 min and achieved 78% degradation efficiency for methylene blue in 36 min. The reactive species trapping experiments revealed that the key active species like O₂ ^•-, ^•OH, and h⁺ can exist and play an important role in methylene blue photodegradation.

Effect of calcination temperature on morphology and phase transformation of MnO2 nanoparticles: A step towards green synthesis for reactive dye adsorption

Green synthesis of manganese oxide nanoparticles (NPs) was carried out by sol-gel method using Acacia Concinna fruit extract for removal of reactive dye. The effect of calcination temperature on its morphology was investigated. α-MnO₂ and Mn₃O₄ NPs were synthesized at 400 °C and 900 °C respectively and were characterized by PXRD, SEM, TEM, FTIR, BET, Raman and TGA. As-synthesized MnO₂ NPs were investigated for the adsorption of Reactive Blue 21 (RB-21) dye. The effect of pH, adsorbent dose, agitation speed, initial dye concentration and temperature on dye removal was explored. pH_pzc was calculated from zeta potential study showing positive surface charge below pH 3.18 resulting in electrostatic force of attraction between adsorbate and adsorbent. Both linear and non-linear regression approaches were utilised for the fitting of kinetic models and adsorption isotherms. Adsorption data follows a pseudo second order kinetics and fits well with the Freundlich isotherm model. Thermodynamic parameters such as ΔH^o, ΔS^o and ΔG^o were determined. The dye removal efficiency, in case of MnO₂ NPs at pH 3.0 was obtained to be 98% whereas for Mn₃O₄, no such dye adsorption was observed. The mechanism of adsorption was studied theoretically confirming π-π interaction and H-bonding between the MnO₂ and RB dye molecules.

Preparation of Zirconium Hydrogen Phosphate Coatings on Sandblasted/Acid-Etched Titanium for Enhancing Its Osteoinductivity and Friction/Corrosion Resistance

Background

Sandblasted/acid-etched titanium (SLA-Ti) implants are widely used for dental implant restoration in edentulous patients. However, the poor osteoinductivity and the large amount of Ti particles/ions released due to friction or corrosion will affect its long-term success rate.

Purpose

Various zirconium hydrogen phosphate (ZrP) coatings were prepared on SLA-Ti surface to enhance its friction/corrosion resistance and osteoinduction.

Methods

The mixture of ZrCl₄ and H₃PO₄ was first coated on SLA-Ti and then calcined at 450°C for 5 min to form ZrP coatings. In addition to a series of physiochemical characterization such as morphology, roughness, wettability, and chemical composition, their capability of anti-friction and anti-corrosion were further evaluated by friction-wear test and by potential scanning. The viability and osteogenic differentiation of MC3T3-E1 cells on different substrates were investigated via MTT, mineralization and PCR assays.

Results

The characterization results showed that there were no significant changes in the morphology, roughness and wettability of ZrP-modified samples (SLA-ZrP0.5 and SLA-ZrP0.7) compared with SLA group. The results of electrochemical corrosion displayed that both SLA-ZrP0.5 and SLA-ZrP0.7 (especially the latter) had better corrosion resistance than SLA in normal saline and serum-containing medium. SLA-ZrP0.7 also exhibited the best friction resistance and great potential to enhance the spreading, proliferation and osteogenic differentiation of MC3T3-E1 cells.

Conclusion

We determined that SLA-ZrP0.7 had excellent comprehensive properties including anti-corrosion, anti-friction and osteoinduction, which made it have a promising clinical application in dental implant restoration.

Polymer Nanocomposites for Photocatalytic Degradation and Photoinduced Utilizations of Azo-Dyes

Specially designed polymer nanocomposites can photo-catalytically degrade azo dyes in wastewater and textile effluents, among which TiO2-based nanocomposites are outstanding and extensively explored. Other nanocomposites based on natural polymers (i.e., chitosan and kaolin) and the oxides of Al, Au, B, Bi, Fe, Li, and Zr are commonly used. These nanocomposites have better photocatalytic efficiency than pure TiO2 through two considerations: (i) reducing the hole/electron recombination rate by stabilizing the excited electron in the conducting band, which can be achieved in TiO2-nanocomposites with graphene, graphene oxide, hexagonal boron nitride (h-BN), metal nanoparticles, or doping; (ii) decreasing the band energy of semiconductors by forming nanocomposites between TiO2 and other oxides or conducting polymers. Increasing the absorbance efficiency by forming special nanocomposites also increases photocatalytic performance. The photo-induced isomerization is exploited in biological systems, such as artificial muscles, and in technical fields such as memory storage and liquid crystal display. Heteroaryl azo dyes show remarkable shifts in photo-induced isomerization, which can be applied in biological and technical fields in place of azo dyes. The self-assembly methods can be employed to synthesize azo-dye polymer nanocomposites via three types of interactions: electrostatic interactions, London forces or dipole/dipole interactions between azo dyes, and photo alignments.

Starch, cellulose, pectin, gum, alginate, chitin and chitosan derived (nano)materials for sustainable water treatment: A review

Natural biopolymers, polymeric organic molecules produced by living organisms and/or renewable resources, are considered greener, sustainable, and eco-friendly materials. Natural polysaccharides comprising cellulose, chitin/chitosan, starch, gum, alginate, and pectin are sustainable materials owing to their outstanding structural features, abundant availability, and nontoxicity, ease of modification, biocompatibility, and promissing potentials. Plentiful polysaccharides have been utilized for making assorted (nano)catalysts in recent years; fabrication of polysaccharides-supported metal/metal oxide (nano)materials is one of the effective strategies in nanotechnology. Water is one of the world's foremost environmental stress concerns. Nanomaterial-adorned polysaccharides-based entities have functioned as novel and more efficient (nano)catalysts or sorbents in eliminating an array of aqueous pollutants and contaminants, including ionic metals and organic/inorganic pollutants from wastewater. This review encompasses recent advancements, trends and challenges for natural biopolymers assembled from renewable resources for exploitation in the production of starch, cellulose, pectin, gum, alginate, chitin and chitosan-derived (nano)materials.

Effects of α-zirconium phosphate and zirconium organophosphonate on the thermal, mechanical and flame retardant properties of intumescent flame retardant high density polyethylene composites

The combination of synergistic agents with intumescent flame retardants (IFRs) is an excellent strategy for the development of high-performance flame retardant composites. Zirconium-based compounds are multifunctional materials with applications in various fields. In this study, zirconium-based compounds were synthesized and then combined with an IFR composed of ammonium polyphosphate (APP) and tris (2-hydroxyethyl) isocyanurate (THEIC) to prepare flame retardant high density polyethylene (HDPE) composites. α-Zirconium phosphate (α-ZrP) and two organic–inorganic hybrids (zirconium organophosphonate), Zr-ATMP and Zr-PA, were prepared using amino tri (methylene phosphonic acid) (ATMP) and phytic acid (PA), respectively, and their thermal, mechanical and flame retardant properties were characterized by thermogravimetric analysis, tensile test, limiting oxygen index (LOI) measurement and cone calorimetry test. The results showed that the LOI value of HD/IFR/Zr-ATMP composite reached a maximum of 26.2% using 25 wt% of flame retardant containing 3 wt% of Zr-ATMP. Of the three zirconium-based compounds, Zr-ATMP and α-ZrP can reduce the peak heat release rate compared with the composite containing only IFR. However, zirconium-based compounds showed no significant improvement of tensile strength.

Zirconium-based compounds are combined with intumescent flame retardant (IFR) to prepare flame retardant high density polyethylene composites.

Self-Assembled Carbohydrate Polymers for Food Applications: A Review

The self-assembled natural and synthetic polymers are booming. However, natural polymers obtained from native or modified carbohydrate polymers (CPs), such as celluloses, chitosan, glucans, gums, pectins, and starches, have had special attention as raw material in the manufacture of self-assembled polymer composite materials having several forms: films, hydrogels, micelles, and particles. The easy manipulation of the architecture of the CPs, as well as their high availability in nature, low cost, and being sustainable and green polymers have been the main positive points in the use of them for different applications. CPs have been used as building blocks for composite structures, and their easy orientation and ordering has given rise to self-assembled CPs (SCPs). These macromolecules have been little studied for food applications. Nonetheless, their research has grown mainly in the last 5 years as encapsulated food additive wall materials, food coatings, and edible films. The multifaceted properties (systems sensitive to pH, temperature, ionic strength, types of ions, mechanical force, and enzymes) of these devices are leading to the development of advanced food materials. This review article focused on the analysis of SCPs for food applications in order to encourage other research groups for their preparation and implementation.