Polymerization of glycidyl methacrylate from the surface of cellulose nanocrystals for the elaboration of PLA-based nanocomposites

Sulfonated cellulose nanocrystal modified with ammonium salt as reinforcement in poly(lactic acid) composite films

Poly(lactic acid) (PLA) composites reinforced with cellulose nanocrystals (CNCs) are promising biodegradable materials. However, the poor compatibility and dispersion of CNCs in the PLA matrix remain a significant obstacle to improving the properties of composites. In this study, the modified CNC (CNC-D) was prepared through sulfonation treatment, followed by modification with didecyl dimethyl ammonium chloride (DDAC). Then, CNC-D was mixed with PLA to prepare composite films (PLA-CNC-D). The results revealed that the PLA-CNC-D had higher tensile strength and elongation at break than PLA-CNC at 3 wt% nanofiller content, increasing by 41.53 and 22.18 %, respectively. SEM and DSC analysis indicated that surface modification improved the compatibility and dispersion of CNC-D in the PLA matrix. The sulfonation process increased the anion content on the surface of CNC-D, enabling the CNC-D surface to adsorb more cationic DDAC, consequently sharply reducing the hydrophilicity of CNC-D. Moreover, the PLA-CNC-D exhibited excellent antibacterial activity against S. aureus and E. coli. In summary, this study provides a novel CNC modification approach to enhance the physical properties and antibacterial activity of PLA composite films, enlarging the application of degradable PLA composites.

Modification of nanocellulose via atom transfer radical polymerization and its reinforcing effect in waterborne UV-curable resin

Cellulose nanocrystals (CNCs) are green reinforcing materials, and their potential has been evaluated in the preparation of waterborne UV-curable resin composites with high-performance. Herein, we present a novel and scalable approach for preparing surface-modified CNCs with acrylic-based polymers to strengthen the compatibility and interaction between CNCs and UV-curable resins. Using tert-butyl acrylate as the monomer, the nanocellulose grafted copolymer CNC-g-PtBA was successfully synthesized via atom transfer radical polymerization (ATRP) in the presence of a macromolecular initiator. Then, the CNC-g-PtBA is blended into the acrylic resin as a nanofiller to prepare the UV-curable nanocomposite. The results indicated that the contact angle of the CNCs increased from 38.7° to approximately 74.8°, and their thermal stability was significantly improved after graft modification. This contributed to the effective alleviation of the agglomeration phenomenon of nanocomposites due to the high hydrophilicity of pure CNCs. Notably, not only was the UV curing efficiency of the nanocomposites greatly increased but the mechanical properties were also further enhanced. Specifically, with the addition of 0.5 wt% CNC-g-PtBA, the curing time of the nanocomposite was shortened from >30 mins down to approximately 6 mins, and the bending strength was increased from 10 MPa for the original resin and 5 MPa for the addition of pure CNCs to 14.3 MPa, and the bending modulus was also greatly increased (up to approximately 730 MPa). Compared to pure CNCs, they are compatible with the resin, exhibiting high mechanical strength and flexibility, and have virtually no effect on the light transmission of the nanocomposites. Additionally, dielectric analysis (DEA) was used to monitor the dielectric constant and conductivity of the UV-curable nanocomposites in real time to further characterize their curing kinetics. The permittivity of these nanocomposites increased by 125 % compared to pristine resin, which shows potential for applications in high dielectric composites or for improving electrical conductivity. This work provides a feasible method for preparing UV-curable nanocomposites with high curing efficiency and permittivity, realizing a wider application of this high-performance nanocomposite.

Cellulose-based polypropoxy ether carboxylates as highly compatible, effective, and migration-resistant plasticizers for poly (lactic acid)

The utilization of cellulose for enhancing the strength, the PLA has received significant attention, however, poor interfacial compatibility of solid cellulose with PLA matrix still hinders their broader application. Herein, highly compatible cellulose-based polypropoxy ether carboxylates (CPPEC) were firstly manufactured via propoxylation of cellulose and following esterification with acetic acid, butyric acid, as well as oleic acid, respectively. Liquid CPPEC delivered excellent performances to PLA, especially, the values of elongation at break and low-temperature resistance of PLA blended with cellulose-based polypropoxy ether acetate (PLA/CPPEA) were respectively increased by 630.9 % and 146.3 % compared with those of neat PLA due to the synergistic effect of propyl and methyl groups in CPPEC with PLA matrix. Additionally, migration resistance of PLA/CPPEA increased 14.3 and 11.2 times, respectively, compared with those of PLA specimens blended with epoxidized soybean oil and dioctyl phthalate. All findings suggest that the CPPEC is suitable for large-scale application in the PLA industry.

Poly(glycidyl methacrylate) modified cellulose nanocrystals and their PBAT-based nanocomposites

Melt processing of cellulose nanocrystals (CNCs) reinforced nanocomposites is still a serious challenge due to the hydrophilic nature of CNCs and their severe agglomeration tendency within the polymer melt. In this study, chemical modification of CNC through grafting poly(glycidyl methacrylate) (PGMA) with various degrees was implemented. Wettability of the modified CNCs (mCNCs) were controlled and their structure was characterized through Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), optical microscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The nanocomposites of polybutylene adipate terephthalate (PBAT) with 3 wt% CNC and mCNC were prepared using an internal melt mixer. To differentiate the effects of CNC and PGMA molecules on the final properties of nanocomposites, PBAT/PGMA compounds were separately prepared. To confirm the chain characterization and molecular weight of the synthesized PGMAs, 1H NMR and gel permeation chromatography (GPC) analysis were conducted. Melt rheological analysis, dynamic mechanical analysis (DMA), DSC, and atomic force microscopy (AFM) were used to monitor the mCNC dispersion quality and the effect of PGMA modification in PBAT compounds. The results revealed that grafting CNC with longer PGMA considerably improved the CNCs' dispersion quality within PBAT. Such dispersion enhancement of long-chain mCNCs and interfacial interaction of PGMA and PBAT resulted in a noticeable increase in storage modulus and complex viscosity of the final nanocomposites.

Cellulose-supported bioadsorbent from natural hemp fiber for removal of anionic dyes from aqueous solution

The aim of this study is to prepare an eco-friendly bioadsorbent by graft copolymerization and modification from hemp fiber including bio-macromolecules such as cellulose, hemicellulose and lignin for anionic dyes adsorption from aqueous solutions, and to investigate adsorptive properties. The prepared cellulose-supported bioadsorbent (TEPA-(GMA-g-HF)) was characterized in detail using SEM-EDX, STEM, FTIR, XRD, TGA and BET techniques and calculating the point of zero charge. It was used as an adsorbent to remove three different anionic dyes, Remazol Brilliant Blue R (RBBR), Reactive Red 120 (RR120) and Reactive yellow 160 (RY160) from the aqueous medium. The effects of adsorbent amount, pH, initial dye concentration, time and temperature on the adsorption were investigated. From the results, it was determined that the adsorption of all three dyes to the developed fibrous bioadsorbent was more compatible with the pseudo-second-order kinetic and the Langmuir isotherm model. It was found that the adsorption capacity increased with increasing temperature, and the adsorption capacity at 298 K was 91.70 mg/g for RBBR, 83.33 for RY160 and 76.34 mg/g for RR120, respectively. Dye removal efficiencies were provided as approximately 100 % at acidic pHs. This high removal efficiency has also achieved in the dense matrix medium, and even after five consecutive reused.

Tunable poly(lauryl methacrylate) surface grafting via SI-ATRP on a one-pot synthesized cellulose nanofibril macroinitiator core as a shear-thinning rheology modifier and drag reducer

The optimally one-pot synthesized 2-bromoproponyl esterified cellulose nanofibril (Br-CNF) has been validated as a robust macroinitiator for self-surface-initiated atom transfer radical polymerization (SI-ATRP) of lauryl methacrylate (LMA) in tunable graft lengths and high conversions of up to 92.7%. SI-ATRP of LMA surface brushes on Br-CNF followed first order kinetics in lengths at up to 46 degree of polymerization (DP) based on mass balance or 31 DP by solution-state 1H NMR in DMSO-d6. With increasing PLMA graft lengths, Br-CNF-g-PLMA cast films exhibited increasing hydrophobicity with water contact angles from 80.9° to 110.6°. The novel Br-CNF-g-PLMA exhibited dual shear thinning behavior of the Br-CNF core as evident by n < 1 flow behavior index and drag reducing properties of PLMA grafts with increased viscosity at up to 21 071×. Br-CNF-g-PLMA with 46 DP could be fully dispersed in silicon pump oil to function as a drag reducer to enhance viscosity up to 5× at 25, 40, and 55 °C. The novel macroinitiator capability of Br-CNF in SI-ATRP of vinyl monomers and the bottlebrush-like LMA surface grafted Br-CNF as highly effective viscosity modifier and drag reducer further demonstrate the versatile functionality of Br-CNF beyond hydrophobic coatings and reactive polyols previously reported.

Microfiber Emissions from Functionalized Textiles: Potential Threat for Human Health and Environmental Risks

The growing worldwide population is directly responsible for the increased production and consumption of textile products. One of the key reasons for the generation of microfibers is the use of textiles and garment materials, which is expected to increase. The textile industry is responsible for the invisible pollution that is created by textile microfibers, which have been detected in marine sediments and organisms. The present review paper demonstrates that the microfibers discharged from functionalized textiles exhibit non-biodegradable characteristics and that a considerable proportion of them possess toxic properties. This is primarily attributed to the impact of textiles' material functionalization on their biodegradability. The potential for these microfibers, which are released from textiles that contain a variety of dyes, toxic chemicals, and nanomaterials, to pose a variety of health risks to both humans and other living organisms is discussed in this paper. In addition, this paper covers a wide variety of preventative and minimizing measures for reduction, which are discussed in terms of several phases ranging from sustainable production through the consumer, end of life, domestic washing, and wastewater treatment phases.

Impact of interactions between peanut protein isolate and cellulose nanocrystals on the properties of Pickering emulsions: Rheological properties and physical stabilities

The interactions between cellulose nanocrystals and proteins can regulate the interfacial properties of Pickering emulsions, which plays a leading role in the stabilities of Pickering emulsions. In this work, oil-in-water (O/W) Pickering emulsions with different oil-water ratios were prepared using peanut protein isolate modified by cellulose nanocrystals (PPI/CL-CNCs). The distributions of PPI/CL-CNCs at the oil-water interfaces and the microstructures of Pickering emulsions were observed by CLSM and cryo-SEM. The results showed that stable complexes PPI/CL-CNCs formed thick and dense interface layers on the surface of oil droplets. The results of rheological tests clarified that the Pickering emulsions showed an elastic and gel texture, and their gel strength could be enhanced by regulating the oil-water ratios from 3:7 to 7:3. In addition, after one month of storage, the EI of all emulsions remained above 92 % with no obvious phase separation or demulsification. These results suggested that the PPI/CL-CNCs-stabilized Pickering emulsions showed good physical stabilities. The study on the rheological properties and physical stabilities of PPI/CL-CNCs-based Pickering emulsions provided novel insights on developing highly stable Pickering emulsions.

Resilient high oxygen barrier multilayer films of nanocellulose and polylactide

Nanocelluloses are promising high gas barrier materials for biobased food packaging, but they must be protected from water to preserve high performance. The respective O₂ barrier properties of different types of nanocelluloses were compared (nanofibers (CNF), oxidized nanofibers (CNF TEMPO) and nanocrystals (CNC)). The oxygen barrier performance for all types of nanocelluloses was similarly high. To protect the nanocellulose films from water, a multilayer material architecture was used with poly(lactide) (PLA) on the outside. To achieve this, a biobased tie layer was developed, using Corona treatment and chitosan. This allowed thin film coating with nanocellulose layers between 60 and 440 nm thickness. AFM images treated with Fast Fourier Transform showed the formation of locally-oriented CNC layers on the film. Coated PLA(CNC) films performed better (3.2 × 10^-20 m³.m/m².s.Pa) than PLA(CNF) and PLA(CNF TEMPO) (1.1 × 10^-19 at best), because thicker layers could be obtained. The oxygen barrier properties were constant during successive measurements at 0 % RH, 80 % RH and again at 0 % RH. This shows that PLA is sufficiently shielding nanocelluloses from water uptake to keep high performance in an extended range of RH and opens the way to high oxygen barrier films which are biobased and biodegradable.

Copolymers Derived from Two Active Esters: Synthesis, Characterization, Thermal Properties, and Reactivity in Post-Modification

Copolymers with two distinguished reactive repeating units are of great interest, as such copolymers might open the possibility of obtaining selective and/or consequent copolymers with different chemical structures and properties. In the present work, copolymers based on two active esters (pentafluorophenyl methacrylate and p-nitrophenyl methacrylate) with varied compositions were synthesized by Cu(0)-mediated reversible deactivation radical polymerization. This polymerization technique allows the preparation of copolymers with high to quantitative conversion of both comonomers, with moderate control over dispersity (Đ = 1.3–1.7). Additionally, by in-depth study on the composition of each copolymer by various techniques including elemental analysis, NMR, FT-IR, and XPS, it was possible to confirm the coherence between expected and obtained composition. Thermal analyses by DSC and TGA were implemented to investigate the relation between copolymers’ composition and their thermal properties. Finally, an evaluation of the difference in reactivity of the two monomer moieties was confirmed by post-modification of copolymers with a primary amine and a primary alcohol as the model.

2-Bromopropionyl Esterified Cellulose Nanofibrils as Chain Extenders or Polyols in Stoichiometrically Optimized Syntheses of High-Strength Polyurethanes

2-Bromopropionyl bromide esterified cellulose nanofibrils (Br-CNFs) facilely synthesized from one-pot esterification of cellulose and in situ ultrasonication exhibited excellent N,N-dimethylformamide (DMF) dispersibility and reactivity to partially replace either chain extender or soft segment diol in the stoichiometrically optimized syntheses of polyurethanes (PUs). PUs polymerized with Br-CNF to replace either 11 mol% 1,4-butadiol chain extender OHs or 1.8 mol% polytetramethylene ether glycol OHs, i.e., 1.5 or 0.3 wt% Br-CNF in PUs, exhibited an over 3 times increased modulus, nearly 4 times higher strength, and a 50% increase in strain. In either role, the experimental modulus exceeding those predicted by the Halpin-Tsai model gave evidence of the stoichiometrically optimized covalent bonding with Br-CNF, while the improved strain was attributed to increased hydrogen-bonding interactions between Br-CNF and the soft segment. These new Br-CNFs not only offer novel synthetic strategies to incorporate nanocelluloses in polyurethanes but also maximize their reinforcing effects via their versatile polyol reactant and cross-linking roles, demonstrating promising applications in the synthesis of other polymers.

Dispersibility Characterization of Cellulose Nanocrystals in Polymeric-Based Composites

Cellulose nanocrystals (CNCs) are hydrophilic nanoparticles extracted from biomass with properties and functions different from cellulose and are being developed for property-oriented applications such as high stiffness, abundant active groups, and biocompatibility. It has broad application prospects in the field of composite materials, while the dispersibility of the CNC in polymers is the key to its application performance. Many reviews have discussed in-depth the modification strategies to improve the dispersibility of the CNC and summarized all characterization for the CNC, but there are no reviews on the in-depth exploration of dispersion characterization. This review is a comprehensive summary of the characterization of CNC dispersion in the matrix in terms of direct observation, indirect evaluation, and quantified evaluation, summarizing how and why different characterization tools reveal dispersibility. In addition, "decision tree" flowcharts are presented to provide the reader with a reference for selecting the appropriate characterization method for a specific composite.

Poly(lactic acid)/Poly(3-hydroxybutyrate) Biocomposites with Differently Treated Cellulose Fibers

The growing concern about environmental pollution has generated an increased demand for biobased and biodegradable materials intended particularly for the packaging sector. Thus, this study focuses on the effect of two different cellulosic reinforcements and plasticized poly(3-hydroxybutyrate) (PHB) on the properties of poly(lactic acid) (PLA). The cellulose fibers containing lignin (CFw) were isolated from wood waste by mechanical treatment, while the ones without lignin (CF) were obtained from pure cellulose by acid hydrolysis. The biocomposites were prepared by means of a melt compounding-masterbatch technique for the better dispersion of additives. The effect of the presence or absence of lignin and of the size of the cellulosic fibers on the properties of PLA and PLA/PHB was emphasized by using in situ X-ray diffraction, polarized optical microscopy, atomic force microscopy, and mechanical and thermal analyses. An improvement of the mechanical properties of PLA and PLA/PHB was achieved in the presence of CF fibers due to their smaller size, while CFw fibers promoted an increased thermal stability of PLA/PHB, owing to the presence of lignin. The overall thermal and mechanical results show the great potential of using cheap cellulose fibers from wood waste to obtain PLA/PHB-based materials for packaging applications as an alternative to using fossil based materials. In addition, in situ X-ray diffraction analysis over a large temperature range has proven to be a useful technique to better understand changes in the crystal structure of complex biomaterials.

Incorporation of Polymer-Grafted Cellulose Nanocrystals into Latex-Based Pressure-Sensitive Adhesives

While the improvement of water-based adhesives with renewable additives is important as industry shifts toward more sustainable practices, a complete understanding of how the compatibility between additives and polymers affects adhesive performance is currently lacking. To elucidate these links, cellulose nanocrystals (CNCs) were first functionalized via surface-initiated atom-transfer radical polymerization with the hydrophobic polymers poly(butyl acrylate) (PBA) and poly(methyl methacrylate) (PMMA) to facilitate their incorporation into latex-based pressure-sensitive adhesives (PSAs). Next, PBA latexes were synthesized using seeded semibatch emulsion polymerization with unmodified or polymer-grafted CNCs added in situ at a loading of 0.5 or 1 phm (parts per hundred parts of monomer). Viscosity and electron microscopy suggested that the polymer-grafted CNCs were incorporated inside or on the latex particles. PSAs containing any CNC type had one or more improved properties (compared to the no-CNC "base case"); CNCs with a low degree of polymerization (DP) grafts exhibited improved tack (up to 2.5-fold higher) and peel strength (up to 6-fold higher) relative to PSAs with unmodified CNCs. The best performing PSA contained the low DP PMMA-grafted CNCs, which is attributed to the higher glass transition temperature and the higher wettability of the PMMA grafts compared to PBA, and the more uniform dispersion of polymer-grafted CNCs throughout the PSA film. In contrast, PSAs containing CNCs with high DP grafts resulted in reduced tack and peel strength (compared to low DP grafts) due to enhanced CNC aggregation. Unfortunately, all PSAs containing polymer-grafted CNCs exhibited inferior shear strength relative to PSAs with unmodified CNCs (and comparable shear strength to the no-CNC "base case"). Collectively, these results provide guidelines for future optimization of more sustainable latex-based PSAs.

Surface modification of cellulose nanocrystals via SI-AGET ATRP and application in waterborne coating for removing of formaldehyde

The hazardous indoor air pollutants of formaldehyde (HCHO) are harmful for human health. Nowadays, it is important to design and fabricate green and efficient HCHO removal materials for HCHO removal from polluted indoor air. In this manuscript, cellulose nanocrystals (CNCs) as green nanomaterials were successfully surface-initiated by 2-(methacryloyloxy)ethyl acetoacetate (MEAA) as functional monomer via surface-initiated Activator Generated by Electron Transfer Atom Transfer Radical Polymerization (SI-AGET ATRP) for the application in removal of HCHO. The employment of CNCs/Poly(2-(methacryloyloxy)ethyl acetoacetate) (CNCs@PMEAA) as nanocomposites were further implanted self-healing waterborne coating for an effective way to remove HCHO. From the result, the HCHO removal efficiency reached 97.5% of CNCs@PMEAA-type coating within 300 min at room temperature, which was much higher than that of the conventional coating (82.8%). This study provides some promising green methods for designing nanocomposite's waterborne coating to remove HCHO at room temperature.

Effect of Reaction Media on Grafting Hydrophobic Polymers from Cellulose Nanocrystals via Surface-Initiated Atom-Transfer Radical Polymerization

Hydrophobic polymer-grafted cellulose nanocrystals (CNCs) were produced via surface-initiated atom-transfer radical polymerization (SI-ATRP) in two different solvents to examine the role of reaction media on the extent of surface modification. Poly(butyl acrylate)-grafted CNCs were synthesized in either dimethylformamide (DMF) (D-PBA-g-CNCs) or toluene (T-PBA-g-CNCs) alongside a free polymer from a sacrificial initiator. The colloidal stability of unmodified CNCs, initiator-modified CNCs, and PBA-g-CNCs in water, DMF, and toluene was evaluated by optical transmittance. The enhanced colloidal stability of initiator-modified CNCs in DMF led to improved accessibility to initiator groups during polymer grafting; D-PBA-g-CNCs had 30 times more grafted chains than T-PBA-g-CNCs, determined by thermogravimetric and elemental analysis. D-PBA-g-CNCs dispersed well in toluene and were hydrophobic with a water contact angle of 124° (for polymer grafts > 13 kDa) compared to 25° for T-PBA-g-CNCs. The cellulose crystal structure was preserved, and individual nanoparticles were retained when grafting was carried out in either solvent. This work highlights that optimizing CNC colloidal stability prior to grafting is more crucial than solvent-polymer compatibility to obtain high graft densities and highly hydrophobic CNCs via SI-ATRP.

Structure-Property Relationships in Bionanocomposites for Pipe Extrusion Applications

In this work, bionanocomposites based on different biodegradable polymers and two types of nanofillers, namely a nanosized calcium carbonate and an organomodified nanoclay, were produced through melt extrusion, with the aim to evaluate the possible applications of these materials as a potential alternative to traditional fossil fuel-derived polyolefins, for the production of irrigation pipes. The rheological behavior of the formulated systems was thoroughly evaluated by exploiting different flow regimes, and the obtained results indicated a remarkable effect of the introduced nanofillers on the low-frequency rheological response, especially in nanoclay-based bionanocomposites. Conversely, the shear viscosity at a high shear rate was almost unaffected by the presence of both types of nanofillers, as well as the rheological response under nonisothermal elongational flow. In addition, the analysis of the mechanical properties of the formulated materials indicated that the embedded nanofillers increased the elastic modulus when compared to the unfilled counterparts, notwithstanding a slight decrease of the material ductility. Finally, the processing behavior of unfilled biopolymers and bionanocomposites was evaluated, allowing for selecting the most suitable material and thus fulfilling the processability requirements for pipe extrusion applications.

Eco-friendly gelatin films with rosin-grafted cellulose nanocrystals for antimicrobial packaging

We report on gelatin films incorporating rosin-grafted cellulose nanocrystals (r-CNCs), which fulfill the most relevant requirements for antimicrobial packaging applications. Transparent gelatin/r-CNCs bionanocomposite films (0.5-6 wt% r-CNCs) were obtained by solution casting and displayed high UV-barrier properties, which were superior to the most used plastic packaging films. The gelatin/r-CNCs films exhibited a moderate water vapor permeability (0.09 g mm/m² h kPa), and high tensile strength (40 MPa) and Young's modulus (1.9 GPa). The r-CNCs were more efficient in improving the optical, water vapor barrier and tensile properties of gelatin films than conventional CNCs. Grafting of rosin on CNCs resulted in an antimicrobial nanocellulose that inhibited the growth of Staphylococcus aureus and Escherichia coli. The antibacterial properties of r-CNCs were sustained in the gelatin films, as demonstrated by agar diffusion tests and proof-of-principle experiments involving cheese storage. Overall, the incorporation of r-CNCs as active fillers in gelatin films is a suitable approach for producing novel eco-friendly, antimicrobial packaging materials.

Polymer Brushes via Surface-Initiated Electrochemically Mediated ATRP: Role of a Sacrificial Initiator in Polymerization of Acrylates on Silicon Substrates

Silicon wafers as semiconductors are essential components of integrated circuits in electronic devices. For this reason, modification of the silicon surface is an important factor in the manufacturing of new hybrid materials applied in micro- and nanoelectronics. Herein, copolymer brushes of hydrophilic poly(2-hydroxyethyl acrylate) (PHEA) and hydrophobic poly(tert-butyl acrylate) (PtBA) were grafted from silicon wafers via simplified electrochemically mediated atom transfer radical polymerization (seATRP) according to a surface-initiated approach. The syntheses of PHEA-b-PtBA copolymers were carried out with diminished catalytic complex concentration (successively 25 and 6 ppm of Cu). In order to optimize the reaction condition, the effect of the addition of a supporting electrolyte was investigated. A controlled increase in PHEA brush thickness was confirmed by atomic force microscopy (AFM). Various other parameters including contact angles and free surface energy (FSE) for the modified silicon wafer were presented. Furthermore, the effect of the presence of a sacrificial initiator in solution on the thickness of the grafted brushes was reported. Successfully fabricated inorganic–organic hybrid nanomaterials show potential application in biomedicine and microelectronics devices, e.g., biosensors.