Room temperature preparation of cellulose nanocrystals with high yield via a new ZnCl2 solvent system

Effect of degree of polymerization on regenerated cellulose ultrafiltration membrane performance through ZnCl2/AlCl3 aqueous solvent system

The development of a direct method for preparing regenerated cellulose (RC) ultrafiltration membranes from cellulose is urgently needed. In this study, refined cotton was used as the raw material to successfully prepare RC ultrafiltration membranes at room temperature using a ZnCl2/AlCl3 solvent system combined with a nonsolvent-induced phase separation (NIPS) method. This solvent system effectively degrades cellulose, producing RC ultrafiltration membranes with varying degrees of polymerization (DP). The research results indicate that reducing the DP of cellulose significantly decreases the viscosity of the solution, facilitating the formation of an asymmetric, finger-like pore structures in the membrane. Furthermore, a decrease in DP slightly enlarges the surface pore size and significantly thickens the dense layer. At a DP of 250, the water flux of the DP250-ET membrane reached 630 L·m-2·h-1·bar-1, with a molecular weight cut-off (MWCO) of ~300 kDa, enabling efficient separation of viruses (LRV > 3.91) and IgG. The exposure of more hydroxy groups on the RC enhances the membrane's hydrophilicity, indicated by a water contact angle (WCA) of 39.5°. Compared to commercial polyethersulfone (PES) membranes, the DP250-ET membrane exhibited lower protein adsorption and excellent anti-fouling performance in practical applications (FRR > 80 %). Overall, this work confirms the significant potential of the eco-friendly ZnCl2/AlCl3 solvent system in the fabrication of RC ultrafiltration membranes, where the structure and performance of the membrane can be tailored by adjusting the DP of cellulose.

Strong, tough, and freeze-tolerant all-natural cellulose-based ionic conductor enabled by multiscale cellulose networks

Soft ionic conductors are widely used in flexible electronics. However, the simultaneous enhancement of their mechanical properties and ionic conductivity remains challenging. This paper reports the successful development of a strong and tough cellulose-based ionic conductor with exceptional mechanical properties and high ionic conductivity by in situ dissolution and reorganization of the fiber matrix of filter paper to create a multiscale structure. The resulting ionic conductor exhibits a fracture strength of 14.13 MPa and a fracture energy of up to 2.84 MJ/m3, exceeding most reported ionic conductors. It also exhibits an impressive ionic conductivity of up to 76.3 mS/cm. Results of experiments on its use in a flexible quasi-solid-state zinc-hybrid supercapacitor show its remarkable features, such as a high capacity of 218 mAh/g, an energy density of 217 Wh/kg, and a power density of 17,520 W/kg. Furthermore, it exhibits excellent temperature resistance, working effectively even at -60 °C. In addition, by incorporating kirigami structures, we fabricated a strain sensor with the cellulose-based ionic conductor with a high gauge factor, as well as a piezoresistive sensor for handwriting recognition and a capacitance pressure sensor for force mapping with wide range and sensitivity. This study opens up new possibilities for fabricating flexible electronics with superior performance using sustainable and renewable resources.

Revisiting various mechanistic approaches for cellulose dissolution in different solvent systems: A comprehensive review

The process of dissolving cellulose is a pivotal step in transforming it into functional, value-added materials, necessitating a thorough comprehension of the underlying mechanisms to refine its advanced processing. This article reviews cellulose dissolution using various solvent systems, along with an in-depth exploration of the associated dissolution mechanisms. The efficacy of different solvents, including aqueous solvents, organic solvents, ionic liquids, hybrid ionic liquid/cosolvent systems, and deep eutectic solvents, in dissolving cellulose is scrutinized, and their limitations and advantages are highlighted. In addition, this review methodically outlines the mechanisms at play within these various solvent systems and the factors influencing cellulose solubility. Conclusions drawn highlight the integral roles of the degree of polymerization, crystallinity, particle size, the type and sizes of cations and anions, alkyl chain length, ionic liquid/cosolvent ratio, viscosity, solvent acidity, basicity, and hydrophobic interactions in the dissolution process. This comprehensive review aims to provide valuable insights for researchers investigating biopolymer dissolution in a broader context, thereby paving the way for broader applications and innovations of these solvent systems.

Oriented bacterial cellulose microfibers with tunable mechanical performance fabricated via green reassembly avenue

Bacterial cellulose has garnered remarkable interest from researchers, particularly those working in the biomedical field. In this work, BC microfibers were fabricated via green dissolution (ZnCl2) and regeneration (ethanol). The orientation of cellulose chains was investigated during extrusion and simple post-processing via polarized optical microscopy and small-angle X-ray scattering. The results implied that the mechanical properties of BC microfibers can be tuned by rational pre-stretching. The BC microfibers can be programmable, and be used to suture hard or soft tissues. The as-designed paralleled BC microfibers have good biocompatibility and can regulate the directional growth of cells on their surface. The as-obtained BC microfiber with a high tensile strength of up to ∼115 MPa is suitable for surgical sutures. The tunable BC microfibers may be utilized as an adequate fiber-derived biomedical material product.

A post-sulfonated one-pot synthesized magnetic cellulose nanocomposite for Knoevenagel and Thorpe-Ziegler reactions

The development of biodegradable and active cellulosic-based heterogeneous catalysts for the synthesis of different organic compounds would be attractive in pharmaceutical and petrochemical-related industries. Herein, a post-sulfonated composite of one-pot synthesized magnetite (Fe3O4) and cellulose nanocrystals (CNCs) was used as an effective and easily separable heterogeneous catalyst for activating the Knoevenagel and Thorpe-Ziegler reactions. The composite was developed hydrothermally from microcrystalline cellulose (MCC), iron chlorides, urea, and hydrochloric acid at 180 °C for 20 h in a one-pot reaction. After collecting the magnetic CNCs (MCNCs), post-sulfonation was performed using chlorosulfonic acid (ClSO3H) in DMF at room temperature producing sulfonated MCNCs (SMCNCs). The results confirmed the presence of sulfonated Fe3O4 and CNCs with a hydrodynamic size of 391 nm (±25). The presence of cellulose was beneficial for preventing Fe3O4 oxidation or the formation of agglomerations without requiring the presence of capping agents, organic solvents, or an inert environment. The SMCNC catalyst was applied to activate the Knoevenagel condensation and the Thorpe-Ziegler reaction with determining the optimal reaction conditions. The presence of the SMCNC catalyst facilitated these transformations under green procedures, which enabled us to synthesize a new series of olefins and thienopyridines, and the yields of some isolated olefins and thienopyridines were up to 99% and 95%, respectively. Besides, the catalyst was stable for five cycles without a significant decrease in its reactivity, and the mechanistic routes of both reactions on the SMCNCs were postulated.

Recent Advances in Cellulose-Based Hydrogels Prepared by Ionic Liquid-Based Processes

This review summarizes the recent advances in preparing cellulose hydrogels via ionic liquid-based processes and the applications of regenerated cellulose hydrogels/iongels in electrochemical materials, separation membranes, and 3D printing bioinks. Cellulose is the most abundant natural polymer, which has attracted great attention due to the demand for eco-friendly and sustainable materials. The sustainability of cellulose products also depends on the selection of the dissolution solvent. The current state of knowledge in cellulose preparation, performed by directly dissolving in ionic liquids and then regenerating in antisolvents, as described in this review, provides innovative ideas from the new findings presented in recent research papers and with the perspective of the current challenges.

One-pot synthesis of magnetic cellulose nanocrystal and its post-functionalization for doxycycline adsorption

The composite of magnetite (Fe₃O₄) and cellulose nanocrystal (CNC) is considered a potential adsorbent for water treatment and environmental remediation. In the current study, a one-pot hydrothermal procedure was utilized for magnetic cellulose nanocrystal (MCNC) development from microcrystalline cellulose (MCC) in the presence of ferric chloride, ferrous chloride, urea, and hydrochloric acid. The x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), and Fourier-transform infrared spectroscopy analysis confirmed the presence of CNC and Fe₃O₄, while transmission electron microscopy (TEM) and dynamic light scattering (DLS) analysis verified their respective sizes (< 400 nm and ≤ 20 nm) in the generated composite. To have an efficient adsorption activity for doxycycline hyclate (DOX), the produced MCNC was post-treated using chloroacetic acid (CAA), chlorosulfonic acid (CSA), or iodobenzene (IB). The introduction of carboxylate, sulfonate, and phenyl groups in the post-treatment was confirmed by FTIR and XPS analysis. Such post treatments decreased the crystallinity index and thermal stability of the samples but improved their DOX adsorption capacity. The adsorption analysis at different pHs revealed the increase in the adsorption capacity by reducing the basicity of the medium due to decreasing electrostatic repulsions and inducing strong attractions.

Facile preparation of cellulose nanocrystals/ZnO hybrids using acidified ZnCl2 as cellulose hydrolytic media and ZnO precursor

Hybridization of nanocellulose with zinc oxide nanoparticles can improve the dispersibility of the zinc oxide and bring new functions to the bio-based products. In this study, cellulose nanocrystal/zinc oxide (CNC/ZnO) nanohybrids with reinforcing and antibacterial properties were prepared via a facile one-pot route. Microcrystalline cellulose (MCC) was first treated with acidified zinc chloride and hydrolyzed into CNCs, which then served as a stabilizing and supporting agent for the in-situ growth of ZnO nanoparticles during subsequent chemical precipitation. The acidified ZnCl₂ solution played a dual role, acting both as cellulose hydrolytic media and as ZnO precursor. By adjusting the pH of the zinc precursor solution (pH = 9-12), well-dispersed rod-like (length: 137.0-468.0 nm, width: 54.1-154.1 nm) and flower-like (average diameter: 179.6 nm) ZnO nanoparticles with hexagonal wurtzite structure were obtained. CNC/ZnO nanohybrids were incorporated into waterborne polyurethane (WPU) films. The Young's modulus and tensile strength of the nanocomposite films increased gradually from 154.8 to 509.0 MPa and from 16.5 to 29.9 MPa, respectively, with increasing CNC/ZnO nanofiller content up to 10 wt%. The 10 % CNC/ZnO composites showed inhibition rates to both E. coli and S. aureus above 88.8 %.