Selective adsorption of uranium (VI) from wastewater using a UiO-66/calcium alginate/hydrothermal carbon composite material

Fabrication of granular three-dimensional graphene oxide/UiO-66 adsorbent for high uranium adsorption: Density functional theory and fixed bed column studies

This study presents a thorough investigation of the novel application of graphene oxide (GO) modified with melamine formaldehyde to fabricate granular three-dimensional GO (3D-GO), followed by the introduction of UiO-66 doping (3D-GO/U) for high uranium (U) adsorption. The U(VI) adsorption isotherms revealed that 3D-GO/U-10 with 10 % UiO-66 incorporation exhibited an impressive adsorption capacity of 375.5 mg g-1 and remained high U(VI) sorption performance in wide pH range. The introduction of UiO-66 to 3D-GO (3D-GO/U-10) led to the deagglomeration of the UiO-66 particles. The in situ surface-enhanced-Raman-spectroscopy-analysis and density-functional-theory simulations showed the symmetric metal center site Zr-O2 on UiO-66 was discovered to exhibit the highest adsorption energy (-3.21 eV) for U(VI) species due to the electrons transfer from the oxygen atom to U(VI) drives the covalent bonding between the symmetric metal center sites Zr-O2 and U(VI) on 3D-GO/U-10. The 3D-GO/U-10 was regenerated using a 0.1 M Na2CO3/0.01 M H2O2 solution and achieved up to 89.7 % U(VI) removal in the 5th cycle. The continuous flow column experiments results revealed 3D-GO/U-10 can regenerate and maintain a U(VI) removal capacity of ∼76 % for up to 4 cycles column experiments. Therefore, 3D-GO/U-10 exhibits great potential for removing U(VI) from water bodies.

Bis-substituted amino acid functionalized chitosan aerogels: High uranium adsorption capacity and antibacterial properties

Based on the goal of "carbon neutralization and carbon peaking", it is still challenging to develop a high adsorption performance and environmentally friendly material for uranium extraction. We proposed a new idea of "Three-Dimensional Environmental-Friendly". A series of amino acid bis-substituted chitosan aerogels (C-1, C-2, C-3, C-4 and C-5) were prepared by ice template method and selective substitution reaction in water environment. Among them, C-3 adsorbent has the antibacterial properties of gram-positive bacteria, gram-negative bacteria and marine bacteria, which is more suitable for uranium adsorption in complex environments. Also, C-3 adsorbent solves the shortcomings of poor adsorption property and easy to cause secondary pollution during modification of traditional chitosan materials. The selectivity and adsorption capacity of uranium are further improved by the unique functional groups of serine residues. At pH = 7, the maximum adsorption capacity reaches 606.32 mg/g. In addition, C-3 adsorbent have excellent selectivity and stability. The synergistic effect of coordination, electrostatic interaction and intraparticle diffusion between C-3 adsorbent and uranium may be the key to its high adsorption performance. The high performance of chitosan adsorbent provides a new idea for the design and application of green and efficient uranium adsorption materials.

Amidoxime-grafted cotton fibers with anti-microbial sludge for efficient uranium recovery

Uranium as a nuclear fuel, its source and aftertreatment has been a hot topic of debate for developers. In this paper, amidoxime and guanidino-modified cotton fibers (DC-AO-PHMG) were synthesized by the two-step functionalization approach, which exhibited remarkable antimicrobial and high uranium recovery property. Adsorption tests revealed that DC-AO-PHMG had excellent selectivity and anti-interference properties, the maximum adsorption capacity of 609.75 mg/g. More than 85 % adsorption capacity could still be kept after 10 adsorption-desorption cycles, and it conformed to the pseudo-second-order kinetic model and the Langmuir adsorption isotherm model as a spontaneous heat-absorbing chemical monolayer process. FT-IR, EDS and XPS analyses speculated that the amidoxime and amino synergistically increased the uranium uptake. The inhibitory activities of DC-AO-PHMG against three aquatic bacteria, BEY, BEL (from Yellow River water and lake bottom silt, respectively) and B. subtilis were significantly stronger, and the uranium adsorption was not impacted by the high bacteria content. Most importantly, DC-AO-PHMG removed up to 94 % of uranium in simulated seawater and extracted up to 4.65 mg/g of uranium from Salt Lake water, which demonstrated its great potential in the field of uranium resource recovery.

Fabrication of Carboxylate-Functionalized 2D MOF Nanosheet with Caged Cavity for Efficient and Selective Extraction of Uranium from Aqueous Solution

The efficient removal of radioactive uranium from aqueous solution is of great significance for the safe and sustainable development of nuclear power. An ultrathin 2D metal-organic framework (MOF) nanosheet with cavity structures was elaborately fabricated based on a calix[4]arene ligand. Incorporating the permanent cavity structures on MOF nanosheet can fully utilize its structural characteristics of largely exposed surface area and accessible adsorption sites in pollutant removal, achieving ultrafast adsorption kinetics, and the functionalized cavity structure would endow the MOF nanosheets with the ability to achieve preconcentration and extraction of uranium from aqueous solution, affording ultrahigh removal efficiency even in ultra-low concentrations. Thus, more than 97% uranium can be removed from the concentration range of 50-500 µg L-1 within 5 min. Moreover, the 2D nano-material exhibits ultra-high anti-interference ability, which can efficiently remove uranium from groundwater and seawater. The adsorption mechanism was investigated by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) analysis, and density functional theory (DFT) calculations, which revealed that the cavity structure plays an important role in uranium capture. This study not only realizes highly efficient uranium removal from aqueous solution but also opens the door to achieving ultrathin MOF nanosheets with cavity structures, which will greatly expand the applications of MOF nanosheets.

Anchoring chitosan/phytic acid complexes on polypyrrole nanotubes as capacitive deionization electrodes for uranium capture from wastewater

Capacitive deionization (CDI) technology holds great potential for rapid and efficient uranyl ion removal from wastewater. However, the related electrode materials still have much room for research. Herein, chitosan/phytic acid complexes were anchored on polypyrrole nanotubes (CS/PA-PPy) to fabricate the electrode for the electrosorption of uranyl ions (UO22+). In this system, polypyrrole nanotubes provided specific channels for ion and electron diffusion, and chitosan/phytic acid complexes offered selective sites for UO22+ binding. The results demonstrated that CS/PA-PPy via electrosorption showed faster kinetics and higher uranium uptake than those via physicochemical adsorption. The maximum adsorption capacity toward UO22+ via electrosorption (1.2 V) could reach 799.3 mg g-1, which was higher than most of the reported CDI electrodes. Electrochemical measurements and experimental characterizations showed that the electrosorption of UO22+ by CS/PA-PPy was a synergistic effect of capacitive process and physicochemical adsorption, in which the capacitive mechanism involved the formation of an electric double layer from hollow polypyrrole nanotubes, whereas the coordination of phosphate, amino and hydroxyl groups with UO22+ was attributed to physicochemical adsorption. With the rational design of material, along with its excellent uranium removal performance, this work exhibited a novel and potential composite electrode for uranium capture via CDI from wastewater.

A sodium alginate gel bead adsorbent doping with amidoxime-modified hydroxyapatite for the efficient adsorption of uranium

In this work, the modified‑sodium alginate gel beads were prepared by sol-gel method. Due to the presence of water channels in the sodium alginate gel bead, amidoxime groups and PO43- were exposed to the surface of the adsorbent to the maximum extent, resulting in the excellent adsorption capacity of modified‑sodium alginate gel beads. The introduction of amidoxime-modified hydroxyapatite significantly improved the adsorption capacity and the adsorption rate of the gel beads. The adsorption capacity increased from 308.7 to 466.0 mg/g and the adsorption equilibrium time was shortened from 300 min to 120 min. The modified‑sodium alginate gel bead possessed the advantages of short adsorption time, high adsorption efficiency and large adsorption capacity, which could be regarded as a potential adsorbent for uranium. Moreover, the uranium removal ability on the modified gel beads was mainly attributed to the Coulomb force between PO43- and uranium and the complexation between uranium and amidoxime groups. In summary, this work would provide a new idea for the modification and application of sodium alginate-based materials.

A critical review of sodium alginate-based composites in water treatment

The global freshwater crisis is a pressing issue, especially in areas with little rainfall and inner continental regions. The growing attention to water scarcity has induced increased interest in research on advanced water treatment technologies. As an abundant bioactive material in nature, sodium alginate (SA) has been widely used in water management due to its outstanding water absorption and holding ability, reversible swelling property, and pollutant adsorption performance. Building on this, progress made in using various modified forms of SA to access clean water is addressed in this review. Covering studies concern the adsorption and separation of pollutants in wastewater by SA-based absorbents and freshwater harvesting by SA-based collectors. This review explores SA-based composites' composition-structure-construction designs and emphasizes the impact of materials like inorganic materials, functional polymers, and porous matrices and how they can be exploited for water treatment. It also highlights the mechanisms of contaminants adsorption and freshwater desorption of SA-based composites. Finally, the shortcomings and future orientation of SA-based composites are proposed, including performance optimization, structural modification, application expansion, and mechanism in-depth investigation. This review aims to offer a theoretical basis and technical guidance for the use of natural materials to respond to the shortage of freshwater resources.

A review of remediation technologies for uranium-contaminated water

Uranium is a naturally existing radioactive element present in the Earth's crust. It exhibits lithophilic characteristics, indicating its tendency to be located near the surface of the Earth and tightly bound to oxygen. It is ecotoxic, hence the need for its removal from the aqueous environment. This paper focuses on the variety of water treatment processes for the removal of uranium from water and this includes physical (membrane separation, adsorption and electrocoagulation), chemical (ion exchange, photocatalysis and persulfate reduction), and biological (bio-reduction and biosorption) approaches. It was observed that membrane filtration and ion exchange are the most popular and promising processes for this application. Membrane processes have high throughput but with the challenge of high power requirements and fouling. Besides high pH sensitivity, ion exchange does not have any major challenges related to its application. Several other unique observations were derived from this review. Chitosan/Chlorella pyrenoidosa composite adsorbent bearing phosphate ligand, hydroxyapatite aerogel and MXene/graphene oxide composite has shown super-adsorbent performance (>1000 mg/g uptake capacity) for uranium. Ultrafiltration (UF) membranes, reverse osmosis (RO) membranes and electrocoagulation have been observed not to go below 97% uranium removal/conversion efficiency for most cases reported in the literature. Heat persulfate reduction has been explored quite recently and shown to achieve as high as 86% uranium reduction efficiency. We anticipate that future studies would explore hybrid processes (which are any combinations of multiple conventional techniques) to solve various aspects of the process design and performance challenges.

Preparation of novel polyvinyl alcohol-carbon nanotubes containing imidazolyl ionic liquid/chitosan hydrogel for highly efficient uranium extraction from seawater

A novel polyvinyl alcohol-carbon nanotube containing an imidazolyl ionic liquid/chitosan composite hydrogel (termed CBCS) was prepared for highly selective uranium adsorption from seawater. The results show that CBCS has good adsorption properties for uranium within the pH range of 5.0-8.0. Kinetics and thermodynamics experiments show that the theoretical maximum adsorption capacity of CBCS to U(VI) is 496.049 mg/g (288 K, pH = 6.0), indicating a spontaneous exothermic reaction. Mechanism analysis shows that the hydroxyl group, amino group, and CN bond on the surface of CBCS directly participate in uranium adsorption and that the dense pores on the surface of CBCS play an important role in uranium adsorption. The competitive adsorption experiment shows that CBCS has excellent uranium adsorption selectivity. In addition, CBCS exhibits good reusability. After five adsorption-desorption cycles, the uranium adsorption rate of CBCS can still reach >98 %. Hence, CBCS has excellent potential for uranium extraction from seawater.

A photothermal MoS2 decorated biomass carbon-based aerogel with a directionally aligned porous structure for mitigating heavy metal stress under seawater acidification

Marine animals and human are threatened by seawater acidification and metal contamination. Especially, the toxicity of copper (Cu) is expected to be boosted with seawater acidification. However, studies on the removal of Cu under seawater acidification are limited for practical applications, owing to obstacles such as instability, secondary contamination, and low adsorption efficiency. In this work, coconut shells were utilized for the synthesis of biomass carbon, which was then decorated with MoS2. A novel porous MoS2/carbon-based aerogel (MCA) with the synergistic effect of photothermal conversion and adsorption was constructed via directional freeze-drying technology. The adsorption properties of MCA were a precise match with Freundlich isotherm and pseudo-second-order kinetic models with a high correlation coefficient (R2) of more than 0.995. Under solar illumination, the surface temperature of MCA reached up to 36.3 °C and the adsorption capacity of MCA increased to 833.8 mg g-1, indicating that the remarkable thermal properties of MCA contributed to achieving high adsorption capacity. The adsorption mechanisms of MCA involved in the removal of Cu(ii) ions were dominated by chemisorption rather than surface physical adsorption. Owing to its outstanding photothermal conversion performance and directionally aligned porous structure, MCA was able to remove Cu(ii) species from seawater, and the adsorption ability of MCA reached 247.1 mg g-1 after ten adsorption cycles. MCA exhibited excellent stability to resist the complex natural environment and was easy to reuse. Overall, MCA with a series of merits, including high adsorption efficiency, excellent photothermal conversion property, and outstanding cycling stability, was confirmed to contribute to addressing heavy metal stress under seawater acidification.

Flexible self-supporting Na3MnTi(PO4)3@C fibers for uranium extraction from seawater by electro sorption

As an eco-friendly technique with the superior adsorption performance, electroadsorption has shown great potential for application in uranium (U(VI)) recovery in recent years. However, the electrodes used in the electrosorption generally suffer the adsorbent to be loaded on the conductors, which greatly limited the adsorption performance of the electrodes for uranyl ions. In present study, a flexible self-supporting Na3MnTi(PO4)3@C fibers (NMTP@C fibers) electrode material was rationally designed and prepared by electrostatic spinning method and annealing technique, and its ability to capture U(VI) efficiently was preliminarily demonstrated by batch adsorption and electro sorption. The plentiful phosphate groups provide sufficient active sites for adsorption, while the axially continuous electron conduction and radially short-range ion transport give NMTP@C fibers fast charge/ion transport capability. The NMTP@C fiber can remove 99% of 5 ppm U(VI) in seawater by electro absorption within 1 h. After several cycles of adsorption under seawater conditions, the adsorbent can still maintain a stable adsorption capacity. The adsorption mechanism of NMTP@C nanofibers for U(VI) was investigated by XPS, FT-IR, Raman, SEM-EDS, and XRD, which was electrostatic interactions and surface complexation. These results suggest that NMTP@C fibers are promising high-capacity adsorbents for efficient and selective capture of U(VI) from seawater.

Fabrication of phosphoric-crosslinked chitosan@g-C3N4 gel beads for uranium(VI) separation from aqueous solution

In this work, a novel g-C₃N₄ filled, phosphoric-crosslinked chitosan gel bead (P-CS@CN) was successfully prepared to adsorb U(VI) from water. The separation performance of chitosan was improved by introducing more functional groups. At pH 5 and 298 K, the adsorption efficiency and adsorption capacity could reach 98.0 % and 416.7 mg g^-1, respectively. After adsorption, the morphological structure of P-CS@CN did not change and adsorption efficiency remained above 90 % after 5 cycles. P-CS@CN exhibited an excellent applicability in water environment based on dynamic adsorption experiments. Thermodynamic analyses demonstrated the value of ΔG, manifesting the spontaneity of U(VI) adsorption process on P-CS@CN. The positive values of ΔH and ΔS showed that the U(VI) removal behavior of P-CS@CN was an endothermic reaction, indicating that the increase of temperature was great benefit to the removal. The adsorption mechanism of P-CS@CN gel bead could be summarized as the complexation reaction with the surface functional groups. This study not only developed an efficient adsorbent for the treatment of radioactive pollutants, but also provided a simple and feasible strategy for the modification of chitosan-based adsorption materials.