Electrocatalysis: A direct alcohol fuel cell and surface science perspective

Electrocatalytic ethanol oxidation reaction: recent progress, challenges, and future prospects

Direct ethanol fuel cells (DEFCs) have been widely considered as a feasible power conversion technology for portable and mobile applications. The economic feasibility of DEFCs relies on two conditions: a notable reduction in the expensive nature of precious metal electrocatalysts and a simultaneous remarkable improvement in the anode's long-term performance. Despite the considerable progress achieved in recent decades in Pt nanoengineering to reduce its loading in catalyst ink with enhanced mass activity, attempts to tackle these problems have yet to be successful. During the ethanol oxidation reaction (EOR) at the anode surface, Pt electrocatalysts lose their electrocatalytic activity rapidly due to poisoning by surface-adsorbed reaction intermediates like CO. This phenomenon leads to a significant loss in electrocatalytic performance within a relatively short time. This review provides an overview of the mechanistic approaches during the EOR of noble metal-based anode materials. Additionally, we emphasized the significance of many essential factors that govern the EOR activity of the electrode surface. Furthermore, we provided a comprehensive examination of the challenges and potential advancements in electrocatalytic EOR.

CoFe-Layered Double Hydroxide Coupled with Pd Particles for Electrocatalytic Ethanol Oxidation

Electrocatalytic efficiency and stability have emerged as critical issues in the ethanol oxidation reaction (EOR) of direct ethanol fuel cells. In this paper, Pd/Co₁Fe₃-LDH/NF as an electrocatalyst for EOR was prepared by a two-step synthetic strategy. Metal-oxygen bonds formed between Pd nanoparticles and Co₁Fe₃-LDH/NF guaranteed structural stability and adequate surface-active site exposure. More importantly, the charge transfer of the formed Pd-O-Co(Fe) bridge could effectively modulate the electrical structure of hybrids, improving the facilitated absorption of OH^- radicals and oxidation of CO_ads. Benefiting from the interfacial interaction, exposed active sites, and structural stability, the observed specific activity for Pd/Co₁Fe₃-LDH/NF (17.46 mA cm^-2) was 97 and 73 times higher than those of commercial Pd/C (20%) (0.18 mA cm^-2) and Pt/C (20%) (0.24 mA cm^-2), respectively. Besides, the j_f/j_r ratio representing the resistance to catalyst poisoning was 1.92 in the Pd/Co₁Fe₃-LDH/NF catalytic system. These results provide insights into optimizing the electronic interaction between metals and the support of electrocatalysts for EOR.

Role of Ni in PtNi Bimetallic Electrocatalysts for Hydrogen and Value-Added Chemicals Coproduction via Glycerol Electrooxidation

Pt-based bimetallic electrocatalysts are promising candidates to convert surplus glycerol from the biodiesel industry to value-added chemicals and coproduce hydrogen. It is expected that the nature and content of the elements in the bimetallic catalyst can not only affect the reaction kinetics but also influence the product selectivity, providing a way to increase the yield of the desired products. Hence, in this work, we investigate the electrochemical oxidation of glycerol on a series of PtNi nanoparticles with increasing Ni content using a combination of physicochemical structural analysis, electrochemical measurements, operando spectroscopic techniques, and advanced product characterizations. With a moderate Ni content and a homogenously alloyed bimetallic Pt-Ni structure, the PtNi2 catalyst displayed the highest reaction activity among all materials studied in this work. In situ FTIR data show that PtNi2 can activate the glycerol molecule at a more negative potential (0.4 V _RHE) than the other PtNi catalysts. In addition, its surface can effectively catalyze the complete C-C bond cleavage, resulting in lower CO poisoning and higher stability. Operando X-ray absorption spectroscopy and UV-vis spectroscopy suggest that glycerol adsorbs strongly onto surface Ni(OH) _x sites, preventing their oxidation and activation of oxygen or hydroxyl from water. As such, we propose that the role of Ni in PtNi toward glycerol oxidation is to tailor the electronic structure of the pure Pt sites rather than a bifunctional mechanism. Our experiments provide guidance for the development of bimetallic catalysts toward highly efficient, selective, and stable glycerol oxidation reactions.

Facile fabrication of highly dispersed Pd catalyst on nanoporous chitosan and its application in environmental catalysis

With the development of society, the problem of environmental pollution is becoming increasingly serious, such as the typical pollution of nitro compounds or dyes in wastewater. An effective strategy to remove these organic pollutants is catalytic conversion, including converting them into more chemically valuable compounds. Herein, a nanoporous chitosan microsphere derived from seafood waste resources of chitin was constructed via sol-gel method, which was used as supports to successfully fabricate a highly dispersed Pd nano-catalyst (mean diameter ~ 1.8 nm) via a facile way based on its interconnected nanoporous structure and rich functional -OH/-NH₂ groups. The synthetic catalyst was applied to the hydrogenation of toxic nitro compounds, which could efficiently and selectively catalyze the conversion of nitro compounds. The catalyst was also used for the degradation of some representative dyes, which also showed good activity and stability, suggesting potential of applications in green environmental governance.

In-Situ surface enhanced infrared absorption spectroscopy study of electrocatalytic oxidation of ethanol on Platinum/Gold surface

The behavior of ethanol oxidation reaction on composite electrodes prepared by deposition platinum on a gold surface (Pt/Au) were studied by cyclic voltammetry and surface enhanced infrared absorption spectroscopy (SEIRAS) analysis. The results show that the Pt electrode has high oxidation activity and significant poison behavior; on the contrary, the Au electrode demonstrates low activity without a poison peak. The SEIRAS analyses reveal that both carbon monoxide (CO) and carbon dioxide (CO₂) appear during anode sweeping, and the CO peak density decreases with increasing potential and finally is eliminated. During the cathodic scanning, the CO peak reappears, and the peak intensity increases with scanning cycles, demonstrating a high poison behavior and the C1 reaction route on Pt. On the Au electrode, CO₂ and CO peaks were not observed; instead, an acetic acid peak appeared, indicating a C2 reaction path. For the Pt/Au composited electrodes, the electrochemical activities of the electrodes, as well as their poison behavior, increased with the deposition amount of Pt. However, the intensities of the poison peaks are smaller than those of oxidation ones; therefore, a higher tolerance to the CO poison can be achieved. For the 2 m-Pt/Au composite electrode, the activity is close to that of pure Pt, but the poison tolerance is 3 times the value of Pt.

Insights into reaction mechanisms of ethanol electrooxidation at the Pt/Au(111) interfaces using density functional theory

Understanding ethanol electrooxidation reaction kinetics is fundamental to the development of direct ethanol fuel cells.

Analysis on production of bioethanol for hydrogen generation

Bioethanol is a renewable energy source carrier mainly produced from the biomass fermentation process. Reforming of bioethanol for hydrogen production is the most promising method from the renewable energy source. Production of hydrogen from ethanol reforming process is not only environmentally friendly, but also it produces greater opportunities for use of renewable energy source, which are available and affect the catalytic activity of the process. This paper reviewed the various reforming processes and associated noble and non-noble catalysts and supporting layers for the reforming process. Among that, electrochemical reforming of bioethanol is found to be cost-effective, and hydrogen production is also found to be of high purity. Hydrogen production from ethanol through various reforming processes is still in the research for better hydrogen production. Hydrogen production through the process of reforming can be widely used for fuel cell operations.

Bifunctional versus Defect-Mediated Effects in Electrocatalytic Methanol Oxidation

The most prominent and intensively studied anode catalyst material for direct methanol oxidation fuel cells consists of a combination of platinum (Pt) and ruthenium (Ru). Classically, their high performance is attributed to a bifunctional reaction mechanism where Ru sites provide oxygen species at lower overpotential than Pt. In turn, they oxidize the adsorbed carbonaceous reaction intermediates at lower overpotential; among these, the Pt site-blocking carbon monoxide. We demonstrate that well-defined Pt modified Ru(0001) single crystal electrodes, with varying Pt contents and different local PtRu configurations at the surface, are unexpectedly inactive for the methanol oxidation reaction. This observation stands in contradiction with theoretical predictions and the concept of bifunctional catalysis for this reaction. Instead, we suggest that pure Pt defect sites play a more critical role than bifunctional defect sites on the electrodes investigated in this work.

A comprehensive and critical review of the recent progress in electrocatalysts for the ethanol oxidation reaction

The human craving for energy is continually mounting and becoming progressively difficult to gratify. At present, the world's massive energy demands are chiefly encountered by nonrenewable and benign fossil fuels. However, the development of dynamic energy cradles for a gradually thriving world to lessen fossil fuel reserve depletion and environmental concerns is currently a persistent issue for society. The discovery of copious nonconventional resources to fill the gap between energy requirements and supply is the extreme obligation of the modern era. A new emergent, clean, and robust alternative to fossil fuels is the fuel cell. Among the different types of fuel cells, the direct ethanol fuel cell (DEFCs) is an outstanding option for light-duty vehicles and portable devices. A critical tactic for obtaining sustainable energy sources is the production of highly proficient, economical and green catalysts for energy storage and conversion devices. To date, a broad range of research is available for using Pt and modified Pt-based electrocatalysts to augment the C2H5OH oxidation process. Pt-based nanocubes, nanorods, nanoflowers, and the hybrids of Pt with metal oxides such as Fe2O3, TiO2, SnO2, MnO, Cu2O, and ZnO, and with conducting polymers are extensively utilized in both acidic and basic media. Moreover, Pd-based materials, transition metal-based materials, as well as transition metal-based materials are also points of interest for researchers nowadays. This review article delivers a broad vision of the current progress of the EOR process concerning noble metals and transition metals-based materials.

Chemical reactions on surfaces for applications in catalysis, gas sensing, adsorption-assisted desalination and Li-ion batteries: opportunities and challenges for surface science

The study of chemical processes on solid surfaces is a powerful tool to discover novel physicochemical concepts with direct implications for processes based on chemical reactions at surfaces, largely exploited by industry. Recent upgrades of experimental tools and computational capabilities, as well as the advent of two-dimensional materials, have opened new opportunities and challenges for surface science. In this Perspective, we highlight recent advances in application fields strictly connected to novel concepts emerging in surface science. Specifically, we show for selected case-study examples that surface oxidation can be unexpectedly beneficial for improving the efficiency in electrocatalysis (the hydrogen evolution reaction and oxygen evolution reaction) and photocatalysis, as well as in gas sensing. Moreover, we discuss the adsorption-assisted mechanism in membrane distillation for seawater desalination, as well as the use of surface-science tools in the study of Li-ion batteries. In all these applications, surface-science methodologies (both experimental and theoretical) have unveiled new physicochemical processes, whose efficiency can be further tuned by controlling surface phenomena, thus paving the way for a new era for the investigation of surfaces and interfaces of nanomaterials. In addition, we discuss the role of surface scientists in contemporary condensed matter physics, taking as case-study examples specific controversial debates concerning unexpected phenomena emerging in nanosheets of layered materials, solved by adopting a surface-science approach.

Electrochemically Controlled Nucleation of Single CO2 Nanobubbles via Formate Oxidation at Pt Nanoelectrodes

CO₂ is an anodic product of many liquid fuel cells. The nucleation of CO₂ nanobubbles during cell operation may block the transport of the fuel to the anode, lowering the overall conversion efficiency. Herein, we report the controlled formation of individual CO₂ nanobubbles at Pt nanoelectrodes via the electrooxidation of formate. The electrochemical data are used to extract key parameters of CO₂ gas nucleation. We determine that CO₂ bubbles nucleate when the concentration of CO₂ at the Pt electrode is greater than ∼0.6 M, corresponding to supersaturation of ∼18. The critical nucleus required for the formation of a CO₂ bubble is measured to have a radius of curvature of ∼100 nm, a contact angle of 173°, and contains ∼70 CO₂ molecules.

Segmentation and Re-encapsulation of Porous PtCu Nanoparticles by Generated Carbon Shell for Enhanced Ethylene Glycol Oxidation and Oxygen-Reduction Reaction

Hierarchical porous carbon-encapsulated ultrasmall PtCu (UsPtCu@C) nanoparticles (NPs) were constructed based on segmentation and re-encapsulation of porous PtCu NPs by using glucose as a green biomass carbon source. The synergistic electronic effect from the bimetallic elements can enhance the catalytic activity by adjusting the surface electronic structure of Pt. Most importantly, the generated porous carbon shell provided a large contact surface area, excellent electrical conductivity, and structural stability, and the ultrasmall PtCu NPs exhibited an increased electrochemical performance compared with their PtCu matrix because of the exposure of more catalytically active centers. This synergistic relationship between the components resulted in enhanced catalytic activity and better stability of the obtained UsPtCu@C for ethylene glycol oxidation reaction and the oxygen-reduction reaction in alkaline electrolyte, which was higher than the PtCu NPs and commercial Pt/C (20 wt % Pt on Vulcan XC-72). The electrochemically active surface areas of the UsPtCu@C, PtCu NPs, and commercial Pt/C were calculated to be approximately 230.2, 32.8, and 64.0 m²/g_Pt, respectively; the mass activity of the UsPtCu@C for the ethylene glycol oxidation reaction was 8.5 A/mg_Pt, which was 14.2 and 8.5 times that of PtCu NPs and commercial Pt/C, respectively. The specific activity of UsPtCu@C was 3.7 mA/cm_pt², which was 2.1 and 2.3 times that of PtCu NPs and commercial Pt/C, respectively. The onset potential (E_on-set) of UsPtCu@C for the oxygen-reduction reaction was 0.96 V (vs reversible hydrogen electrode, RHE), which was 110 and 60 mV higher than PtCu and commercial Pt/C, respectively. The half-wave potentials (E_1/2) of UsPtCu@C, PtCu, and Pt/C were 0.88, 0.56, and 0.82 V (vs RHE), respectively, which indicated that the UsPtCu@C catalyst had an excellent bifunctional electrocatalytic activity.

Advanced Catalytic Materials for Ethanol Oxidation in Direct Ethanol Fuel Cells

Direct ethanol fuel cells (DEFCs) have emerged as promising and advanced power systems that can considerably reduce fossil fuel dependence, and thus have attracted worldwide attention. DEFCs have many apparent merits over the analogous devices fed with hydrogen or methanol. As the key constituents, the catalysts for both cathodes and anodes usually face some problems (such as high cost, low conversion efficiency, and inferior durability) that hinder the commercialization of DEFCs. This review mainly focuses on the most recent advances in nanostructured catalysts for anode materials in DEFCS. First, we summarize the effective strategies used to achieve highly active Pt- and Pd-based catalysts for ethanol electro-oxidation, including composition control, microstructure design, and the optimization of support materials. Second, a few non-precious catalysts based on transition metals (such as Fe, Co, and Ni) are introduced. Finally, we outline the concerns and future development of anode catalysts for DEFCs. This review provides a comprehensive understanding of anode catalysts for ethanol oxidation in DEFCs.

Synthesis and Catalytic Properties of Modified Electrodes by Pulsed Electrodeposition of Pt/PANI Nanocomposite

In this study, the modification of glassy carbon electrodes by potentiostatic pulsed deposition of platinum nanoparticles and potentiostatic pulsed polymerization of polyaniline nanofibers was investigated. During the preparation of the nano-composite materials, the control of the potentiostatic pulsed deposition and potentiostatic pulsed polymerization parameters, such as pulse potential, pulse width time, duty cycle, and platinum precursor concentration allowed the optimization of the size, shape, and distribution of the deposited Pt nanoparticles. It is noteworthy that the polymerization method, cyclic voltammetry method, or potentiostatic pulsed polymerization method show an important effect in the morphology of the deposited polyaniline (PANI) film. The obtained modified electrodes, with highly uniform and well dispersed platinum nanoparticles, exhibit good electrocatalytic properties towards methanol oxidation.

Current progress of metallic and carbon-based nanostructure catalysts towards the electrochemical reduction of CO2

The current design and development of inorganic nanostructured electrocatalysts for carbon dioxide reduction are highlighted in this review.

Fabrication of CuOx-Pd Nanocatalyst Supported on a Glassy Carbon Electrode for Enhanced Formic Acid Electro-Oxidation

Formic acid (FA) electro-oxidation (FAO) was investigated at a binary catalyst composed of palladium nanoparticles (PdNPs) and copper oxide nanowires (CuOxNWs) and assembled onto a glassy carbon (GC) electrode. The deposition sequence of PdNPs and CuOxNWs was properly adjusted in such a way that could improve the electrocatalytic activity and stability of the electrode toward FAO. Several techniques including cyclic voltammetry, chronoamperometry, field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction were all combined to report the catalyst’s activity and to evaluate its morphology, composition, and structure. The highest catalytic activity and stability were obtained at the CuOx/Pd/GC electrode (with PdNPs directly deposited onto the GC electrode followed by CuOxNWs with a surface coverage, Г, of ca. 49%). Such enhancement was inferred from the increase in the peak current of direct FAO (by ca. 1.5 fold) which associated a favorable negative shift in its onset potential (by ca. 30 mV). The enhanced electrocatalytic activity and stability (decreasing the loss of active material by ca. 1.5-fold) of the CuOx/Pd/GC electrode was believed originating both from facilitating the direct oxidation (decreasing the time needed to oxidize a complete monolayer of FA, increasing turnover frequency, by ca. 2.5-fold) and minimizing the poisoning impact (by ca. 71.5%) at the electrode surface during FAO.

Recent advances in the nanoengineering of electrocatalysts for CO2 reduction

Emissions of CO2 from fossil fuel combustion and industrial processes have been regarded as the dominant cause of global warming. Electrochemical CO2 reduction (ECR), ideally in aqueous media, could potentially solve this problem by the storage of energy from renewable sources in the form of chemical energy in fuels or value-added chemicals in a sustainable manner. However, because of the sluggish reaction kinetics of the ECR, efficient, selective, and durable electrocatalysts are required to increase the rate this reaction. Despite considerable progress in using bulk metallic electrodes for catalyzing the ECR, greater efforts are still needed to tackle this grand challenge. In this Review, we highlight recent progress in using nanoengineering strategies to promote the electrocatalysts for the ECR. Through these approaches, considerable improvements in catalytic performance have been achieved. An outlook of future developments in applying and optimizing these strategies is also proposed.

Dense CO Adlayers as Enablers of CO Hydrogenation Turnovers on Ru Surfaces

High CO* coverages lead to rates much higher than Langmuirian treatments predict because co-adsorbate interactions destabilize relevant transition states less than their bound precursors. This is shown here by kinetic and spectroscopic data-interpreted by rate equations modified for thermodynamically nonideal surfaces-and by DFT treatments of CO-covered Ru clusters and lattice models that mimic adlayer densification. At conditions (0.01-1 kPa CO; 500-600 K) which create low CO* coverages (0.3-0.8 ML from in situ infrared spectra), turnover rates are accurately described by Langmuirian models. Infrared bands indicate that adlayers nearly saturate and then gradually densify as pressure increases above 1 kPa CO, and rates become increasingly larger than those predicted from Langmuir treatments (15-fold at 25 kPa and 70-fold at 1 MPa CO). These strong rate enhancements are described here by adapting formalisms for reactions in nonideal and nearly incompressible media (liquids, ultrahigh-pressure gases) to handle the strong co-adsorbate interactions within the nearly incompressible CO* adlayer. These approaches show that rates are enhanced by densifying CO* adlayers because CO hydrogenation has a negative activation area (calculated by DFT), analogous to how increasing pressure enhances rates for liquid-phase reactions with negative activation volumes. Without these co-adsorbate effects and the negative activation area of CO activation, Fischer-Tropsch synthesis would not occur at practical rates. These findings and conceptual frameworks accurately treat dense surface adlayers and are relevant in the general treatment of surface catalysis as it is typically practiced at conditions leading to saturation coverages of reactants or products.

Controlling Palladium Nanocrystals by Solvent-Induced Strategy for Efficient Multiple Liquid Fuels Electrooxidation

Pd has been considered as the possible economical substitute of rare Pt for catalyzing the liquid fuels electrooxidation reaction. However, the biggest problem of Pd nanocatalysts for alcohol oxidations is that they show the limited stability and activity, greatly impacting the development of liquid fuels-based fuel cell technology. We report herein a new solvent-induced procedure for making distinct Pd NCs with geometry tuning from Pd nanosheets, Pd tetrapods, to Pd concave tetrahedra by switching the solvent from 1-methyl-2-pyrrolidone, formamide, to acetylacetonate. The key features for the preparation of dimension-controlled Pd NCs herein are that the use of molybdenum carbonyl (Mo(CO)6) determines the exposed {111} facet in the final Pd NCs, while different solvents control the reduction kinetics to induce the growth of Pd NCs with distinct morphologies. The as-prepared distinct Pd NCs show the interesting shape-dependent electrocatalytic activities toward multiple liquid fuels electrooxidation reactions including ethylene glycol oxidation reaction, glycerol oxidation reaction, ethanol oxidation reaction, and also methanol oxidation reaction with Pd nanosheets exhibiting higher activity than all the other Pd catalysts and higher activity than the commercial Pd/C and also Pd black due to the thin character of Pd nanosheets. Most importantly, the Pd nanosheets exhibit much higher stability for multiple liquid fuels electrooxidation than all the other Pd catalysts tested. The present work gives the first example in exploring the effect of solvent in tuning the dimensions of Pd NCs, and thus optimizing the electrocatalytic performance for liquid fuels electrooxidation.

Theoretical Heterogeneous Catalysis: Scaling Relationships and Computational Catalyst Design

Scaling relationships are theoretical constructs that relate the binding energies of a wide variety of catalytic intermediates across a range of catalyst surfaces. Such relationships are ultimately derived from bond order conservation principles that were first introduced several decades ago. Through the growing power of computational surface science and catalysis, these concepts and their applications have recently begun to have a major impact in studies of catalytic reactivity and heterogeneous catalyst design. In this review, the detailed theory behind scaling relationships is discussed, and the existence of these relationships for catalytic materials ranging from pure metal to oxide surfaces, for numerous classes of molecules, and for a variety of catalytic surface structures is described. The use of the relationships to understand and elucidate reactivity trends across wide classes of catalytic surfaces and, in some cases, to predict optimal catalysts for certain chemical reactions, is explored. Finally, the observation that, in spite of the tremendous power of scaling relationships, their very existence places limits on the maximum rates that may be obtained for the catalyst classes in question is discussed, and promising strategies are explored to overcome these limitations to usher in a new era of theory-driven catalyst design.

Elucidation of the surface structure–selectivity relationship in ethanol electro-oxidation over platinum by density functional theory

We have successfully built a general framework to comprehend the structure–selectivity relationship in ethanol electrooxidation on platinum by density functional theory calculations.

Cuprous oxide template synthesis of hollow-cubic Cu2O@PdxRuynanoparticles for ethanol electrooxidation in alkaline media

Surfactant-free and low Pd loading Cu₂O@Pd_xRu_yhollow-cubes were facilely prepared and their electrocatalytic performance for ethanol electrooxidation were investigated.

Prevalence of Bimolecular Routes in the Activation of Diatomic Molecules with Strong Chemical Bonds (O2, NO, CO, N2) on Catalytic Surfaces

Dissociation of the strong bonds in O2, NO, CO, and N2 often involves large activation barriers on low-index planes of metal particles used as catalysts. These kinetic hurdles reflect the noble nature of some metals (O2 activation on Au), the high coverages of co-reactants (O2 activation during CO oxidation on Pt), or the strength of the chemical bonds (NO on Pt, CO and N2 on Ru). High barriers for direct dissociations from density functional theory (DFT) have led to a consensus that "defects", consisting of low-coordination exposed atoms, are required to cleave such bonds, as calculated by theory and experiments for model surfaces at low coverages. Such sites, however, bind intermediates strongly, rendering them unreactive at the high coverages prevalent during catalysis. Such site requirements are also at odds with turnover rates that often depend weakly on cluster size or are actually higher on larger clusters, even though defects, such as corners and edges, are most abundant on small clusters. This Account illustrates how these apparent inconsistencies are resolved through activations of strong bonds assisted by co-adsorbates on crowded low-index surfaces. Catalytic oxidations occur on Au clusters at low temperatures in spite of large activation barriers for O2 dissociation on Au(111) surfaces, leading to proposals that O2 activation requires low-coordination Au atoms or Au-support interfaces. When H2O is present, however, O2 dissociation proceeds with low barriers on Au(111) because chemisorbed peroxides (*OOH* and *HOOH*) form and weaken O-O bonds before cleavage, thus allowing activation on low-index planes. DFT-derived O2 dissociation barriers are much lower on bare Pt surfaces, but such surfaces are nearly saturated with CO* during CO oxidation. A dearth of vacant sites causes O2* to react with CO* to form *OOCO* intermediates that undergo O-O cleavage. NO-H2 reactions occur on Pt clusters saturated with NO* and H*; direct NO* dissociation requires vacant sites that are scarce on such surfaces. N-O bonds cleave instead via H*-assistance to form *HNOH* intermediates, with barriers much lower than for direct NO* dissociation. CO hydrogenation on Co and Ru occurs on crowded surfaces saturated with CO*; rates increase with increasing Co and Ru cluster size, indicating that low-index surfaces on large clusters can activate CO*. Direct CO*dissociation, however, occurs with high activation barriers on low-index Co and Ru surfaces, and even on defect sites (step-edge, corner sites) at high CO* coverages. CO* dissociation proceeds instead with H*-assistance to form *HCOH* species that cleave C-O bonds with lower barriers than direct CO* dissociation, irrespective of surface coordination. H2O increases CO activation rates by assisting H-additions to form *HCOH*, as in the case of peroxide formation in Au-catalyzed oxidations. N2 dissociation steps in NH3 synthesis on Ru and Fe are thought to also require defect sites; yet, barriers on Ru(0001) indicate that H*-assisted N2 activation - unlike O2, CO, and NO - is not significantly more facile than direct N2 dissociation, suggesting that defects and low-index planes may both contribute to NH3 synthesis rates. The activation of strong chemical bonds often occurs via bimolecular reactions. These steps weaken such bonds before cleavage on crowded low-index surfaces, thus avoiding the ubiquitous kinetic hurdles of direct dissociations without requiring defect sites.

Significance of β-dehydrogenation in ethanol electro-oxidation on platinum doped with Ru, Rh, Pd, Os and Ir

In the exploration of highly efficient direct ethanol fuel cells (DEFCs), how to promote the CO2 selectivity is a key issue which remains to be solved. Some advances have been made, for example, using bimetallic electrocatalysts, Rh has been found to be an efficient additive to platinum to obtain high CO2 selectivity experimentally. In this work, the mechanism of ethanol electrooxidation is investigated using the first principles method. It is found that CH3CHOH* is the key intermediate during ethanol electrooxidation and the activity of β-dehydrogenation is the rate determining factor that affects the completeness of ethanol oxidation. In addition, a series of transition metals (Ru, Rh, Pd, Os and Ir) are alloyed on the top layer of Pt(111) in order to analyze their effects. The elementary steps, α-, β-C-H bond and C-C bond dissociations, are calculated on these bimetallic M/Pt(111) surfaces and the formation potential of OH* from water dissociation is also calculated. We find that the active metals increase the activity of β-dehydrogenation but lower the OH* formation potential resulting in the active site being blocked. By considering both β-dehydrogenation and OH* formation, Ru, Os and Ir are identified to be unsuitable for the promotion of CO2 selectivity and only Rh is able to increase the selectivity of CO2 in DEFCs.

Methanol electro-oxidation on platinum modified tungsten carbides in direct methanol fuel cells: a DFT study

Bilayer Pt-modified WC catalysts exhibit up to 2.4 times higher MOR reactivity compared to that of pure Pt.