Three way catalytic activity of thermally degenerated Pt/Al2O3 and Pt/CeO2–ZrO2 modified Al2O3 model catalysts

Microwave-Based State Diagnosis of Three-Way Catalysts: Impact Factors and Application Recommendations

This study reassesses an overview of the potential of the radio frequency (RF)-based state diagnostics of three-way catalysts (TWC) based on a previous study with an emphasis on the defect chemistry of the catalyst material during reoxidation and reduction. Some data are based on the previous works but are newly processed, and the signal parameters resonant frequency and inverse quality factor are evaluated with respect to applicability. The RF-based method uses electromagnetic resonances in a cavity resonator to provide information on the storage level of the oxygen storage component. The analysis focuses on a holistic investigation and evaluation of the major effects influencing the RF signal during operation. On the one hand, the response to the oxygen storage behavior and the resolution of the measurement method are considered. Therefore, this study merges original data from multiple former publications to provide a comprehensive insight into important measurement effects and their defect chemistry background. On the other hand, the most important cross-sensitivities are discussed and their impact during operation is evaluated. Additionally, the effect of catalyst aging is analyzed. The effects are presented separately for the two resonant parameters: resonant frequency and (unloaded) quality factor. Overall, the data suggest that the quality factor has a way higher signal quality at low temperatures (<400 °C) and the resonant frequency is primarily suitable for high operating temperatures. At most operating points, the quality factor is even more robust against interferences such as exhaust gas stoichiometry and water content. Correctly estimating the catalyst temperature is the most important factor for reliable results, which can be achieved by combining the information of both resonant signals. In the end, the data indicate that microwave-based state diagnosis is a powerful system for evaluating the oxygen storage level over the entire operating range of a TWC. As a research tool and in its application, the system can therefore contribute to the improvement of the emission control of future gasoline vehicles.

Development of a thermally stable Pt catalyst by redispersion between CeO2 and Al2O3

For catalytic systems consisting of Pt as the active component and CeO2-Al2O3 as the support material, the metal-support interaction between the Pt and CeO2 components is widely applied to inhibit aggregation of Pt species and thus enhance the thermal stability of the catalyst. In this work, a highly thermostable Pt catalyst was prepared by modifying the synthesis procedure for conventional Pt/CeO2/Al2O3 (Pt/Ce/Al) catalyst, that is, the CeO2 component was introduced after deposition of Pt on Al2O3. The obtained CeO2/Pt/Al2O3 (Ce/Pt/Al) catalyst exhibits significantly different aging behavior. During the hydrothermal aging process, redispersion of Pt species from the surface of Al2O3 to the surface of CeO2 occurs, resulting in a stronger metal-support interaction between Pt and CeO2. Thus, the formed Pt-O-Ce bond could act as an anchor to retard aggregation of Pt species and help Pt species stay at a more oxidative state. Consequently, excellent reduction capability and superior three-way catalytic performance are acquired by Ce/Pt/Al-a after hydrothermal aging treatment.

Core-shell design and well-dispersed Pd particles for three-way catalysis: Effect of halloysite nanotubes functionalized with Schiff base

In this study, we have described the synthesis of core@shell three-way catalyst with well-dispersed Pd nanoparticles which were intercalated into halloysite nanotubes (HNTs) material via ligand assistance. The prepared parameters of Pd@HNTs catalyst included amine source, the molar ratio of amine and aldehyde, and the addition of CeO₂ promoter. As a result, Pd@HNTs performed a good dispersion of Pd particles and high stability, which is attributed to the strong interaction between Pd and HNTs with Schiff base ligands and the high thermal resistance of HNTs as a sintering barrier. Moreover, the results of various characteristic analyses revealed that Pd@HNT-E12 (ethylenediamine: salicylaldehyde in a molar ratio of 1:2) exhibited the highest gases conversion to the others, which has excellent redox ability. Furthermore, the addition of CeO₂, which acted as both a promoter and a protector, could provide more oxygen vacancies for promoting NO reduction and CO and C₃H₈ oxidation at gradually elevated temperatures. Such core-shell catalyst Ce@Pd@HNT-E12 could avoid excess CeO₂ penetrating into the pore volume of halloysite support and facilitate the three-way catalytic reaction.

Effects of hydrogen peroxide co-precipitation and inert N2 atmosphere calcination on CeZrLaNd mixed oxides and the catalytic performance used on Pd supported three-way catalysts

The unique reversible oxygen storage and release capacity of cerium zirconium mixed oxides makes them ideal washcoat materials of automotive three-way catalysts (TWC). In this work, cerium zirconium mixed oxides of Ce_0.15Zr_0.79La_0.02Nd_0.04O₂ were prepared via a co-precipitation method. The effects of hydrogen peroxide co-precipitation and inert N₂ atmosphere calcination on the structure and properties of cerium zirconium mixed oxides were investigated systematically by Brunauer-Emmett-Teller surface area measurements, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, hydrogen temperature-programmed reduction, oxygen storage capacity (OSC), Raman spectroscopy, and X-ray photoelectron spectroscopy. Additionally, the catalytic performance of palladium supported catalysts was studied. Results show that hydrogen peroxide co-precipitation promotes the dispersion of cerium zirconium particles and enhances crystal grain growth, resulting in good thermal stability of the obtained cerium zirconium mixed oxides. Inert N₂ atmosphere calcination also enhances the dispersion of particles, results in smaller and finer crystal grains, enriches pore channels, and significantly improves the surface area, pore volume and OSC, with an OSC of 424.57 μmolO₂ g^-1, which is a 13.37% increment compared with the common sample. The benefits of hydrogen peroxide co-precipitation and inert N₂ atmosphere calcination endow the Pd supported catalysts of cerium zirconium mixed oxides with good three-way catalytic performance.

Influence of atomic site-specific strain on catalytic activity of supported nanoparticles

Heterogeneous catalysis is an enabling technology that utilises transition metal nanoparticles (NPs) supported on oxides to promote chemical reactions. Structural mismatch at the NP–support interface generates lattice strain that could affect catalytic properties. However, detailed knowledge about strain in supported NPs remains elusive. We experimentally measure the strain at interfaces, surfaces and defects in Pt NPs supported on alumina and ceria with atomic resolution using high-precision scanning transmission electron microscopy. The largest strains are observed at the interfaces and are predominantly compressive. Atomic models of Pt NPs with experimentally measured strain distributions are used for first-principles kinetic Monte Carlo simulations of the CO oxidation reaction. The presence of only a fraction of strained surface atoms is found to affect the turnover frequency. These results provide a quantitative understanding of the relationship between strain and catalytic function and demonstrate that strain engineering can potentially be used for catalyst design.

Detailed knowledge of how strain influences catalytic reactions remains elusive. Here, the authors experimentally measure the strain in supported Pt nanoparticles on alumina and ceria with atomic resolution and computationally explore how the strain affects the CO oxidation reaction.

Dispersion improvement and activity promotion of Pt catalysts supported on a Ce-based support by pH adjustment

Pt-based catalysts prepared by pH adjustment display high dispersion and catalytic activity because of strong Pt precursor–support surface interactions.

Nanofence Stabilized Platinum Nanoparticles Catalyst via Facet-Selective Atomic Layer Deposition

A facet-selective atomic layer deposition method is developed to fabricate oxide nanofence structure to stabilize Pt nanoparticles. CeO_x is selectively deposited on Pt nanoparticles' (111) facets and naturally exposes Pt (100) facets. The facet selectivity is realized through different binding energies of Ce precursor fragments chemisorbed on Pt (111) and Pt (100), which is supported by in situ mass gain experiment and corroborated by density functional theory simulations. Such nanofence structure not only has exposed Pt active facets for carbon monoxide oxidation but also forms ceria-metal interfaces that are beneficial for activity enhancement. The composite catalysts show excellent sintering resistance up to 700 °C calcination. CeO_x anchors Pt nanoparticles with a strong metal oxide interaction, and nanofence structure around Pt nanoparticles provides physical blocking that suppresses particles migration. The study reveals that forming oxide nanofence structure to encapsulate precious metal nanoparticles is an effective way to simultaneously enhance catalytic activity and thermal stability.

Polarization-driven catalysis via ferroelectric oxide surfaces

Ferroelectric polarization can tune the surface chemistry: enhancing technologically important catalytic reactions such as NO_x direct decomposition and SO₂ oxidation.