Nanocomposite materials for photocatalytic degradation of pollutants

WSe2-PPy-Based Type-II Heterostructure for Efficient Photocatalytic Removal of Nitrofurazone

The escalating concerns over water pollution and antimicrobial resistance have underscored the urgency of effective antibiotic degradation. Photocatalytic degradation offers a promising solution due to its efficiency and environmental friendliness. In this study, I synthesized a novel nanocomposite comprising WSe2 and polypyrrole (PPy) via a hydrothermal method coupled with polymerization for the degradation of nitrofurazone antibiotics. The WSe2/PPy nanocomposite demonstrated significantly higher photocatalytic degradation efficiency (94.50%) compared to pure WSe2 and PPy, with degradation efficiencies of 23.07% and 32.96%, respectively. The degradation was performed at different pH values, with acidic conditions proving the most suitable for nitrofurazone degradation. The photocatalytic degradation efficiencies at pH 2, 3, 5, 7, 9, and 11 were 98.5%, 98.3%, 85.4%, 78.02%, 61.4%, and 61%, respectively. The acidic conditions were found to be the most suitable for nitrofurazone degradation. The nanocomposite's improved efficiency was ascribed to its low recombination rate and quick charge transfer, as demonstrated by time-resolved photoluminescence (TRPL) and electrochemical impedance spectroscopy (EIS) tests, respectively. The Z-Scheme photocatalysis mechanism as proposed for the WSe2-PPy nanocomposite and supported by scavenger experiments. Moreover, the nanocomposite demonstrated excellent reusability, which enhanced its practical applicability.

Sulfonated Pentablock Copolymer (NexarTM) for Water Remediation and Other Applications

This review focuses on the use of a sulfonated pentablock copolymer commercialized as NexarTM in water purification applications. The properties and the use of sulfonated copolymers, in general, and of NexarTM, in particular, are described within a brief reference focusing on the problem of different water contaminants, purification technologies, and the use of nanomaterials and nanocomposites for water treatment. In addition to desalination and pervaporation processes, adsorption and photocatalytic processes are also considered here. The reported results confirm the possibility of using NexarTM as a matrix for embedded nanoparticles, exploiting their performance in adsorption and photocatalytic processes and preventing their dispersion in the environment. Furthermore, the reported antimicrobial and antibiofouling properties of NexarTM make it a promising material for achieving active coatings that are able to enhance commercial filter lifetime and performance. The coated filters show selective and efficient removal of cationic contaminants in filtration processes, which is not observed with a bare commercial filter. The UV surface treatment and/or the addition of nanostructures such as graphene oxide (GO) flakes confer NexarTM with coating additional functionalities and activity. Finally, other application fields of this polymer are reported, i.e., energy and/or gas separation, suggesting its possible use as an efficient and economical alternative to the more well-known Nafion polymer.

A Review of Synthesis Methods, Modifications, and Mechanisms of ZnO/TiO2-Based Photocatalysts for Photodegradation of Contaminants

The environment being surrounded by accumulated durable waste organic compounds has become a critical crisis for human societies. Generally, organic effluents of industrial plants released into the water source and air are removed by some physical and chemical processes. Utilizing photocatalysts as cost-effective, accessible, thermally/mechanically stable, nontoxic, reusable, and powerful UV-absorber compounds creates a new gateway toward the removal of dissolved, suspended, and gaseous pollutants even in trace amounts. TiO2 and ZnO are two prevalent photocatalysts in the field of removing contaminants from wastewater and air. Structural modification of the photocatalysts with metals, nonmetals, metal ions, and other semiconductors reduces the band gap energy and agglomeration and increases the affinity toward organic compounds in the composite structures to expand their usability on an industrial scale. This increases the extent of light absorbance and improves the photocatalytic efficiency. Selecting a suitable synthesis method is necessary to prepare a target photocatalyst with distinct properties such as high specific surface area, numerous surface functional groups, and an appropriate crystalline phase. In this Review, significant parameters for the synthesis and modification of TiO2- and ZnO-based photocatalysts are discussed in detail. Several proposed mechanistic routes according to photocatalytic composite structures are provided. Some electrochemical analyses using charge carrier trapping agents and delayed recombination help to plot mechanistic routes according to the direction of photoexcited species (electron-hole pairs) and design more effective photocatalytic processes in terms of cost-effective photocatalysts, saving time and increasing productivity.

Impact of LaZnFe2O4 supported NiWO4@D400-MMT@CMS/MMA nanocomposites as a catalytic system in remediation of dyes from wastewater

Herein, a novel nanocomposite based on lanthanum zinc ferrite and nickel tungstate was created by incorporation between (MMT-jeffamine-400) nanoparticles (NPs), chloromethyl styrene as a binder and polymethyl methacrylate monomer using solution polymerization. The as-designed nanocomposites were employed to confiscate xylenol orange "X.O" as an acidic dye and rhodamine B "RhB" as "an amphoteric dye" from colored wastewater. The impact of several parameters such as solution pH, initial dye concentration, the effect of time, and the effect of temperature was explored. The consequences indicated that the pure organoclay had negligible adsorption while that composed of organoclay with PMMA@CMS-polymer incorporated with LaZnFe2O4@NiWO4 particles detached more than 90% for xylenol orange (XO) and 93% for "rhodamine B" molecules. Electrostatic interactions are the predominant factor in the adsorption of cationic and amphoteric adsorbates, as proven by zeta-potential measurement. Additionally, the adsorbent may be regenerate and utilized up to five times with good adsorption capabilities by adding sodium hydroxide. As a result, the removal can be effectively accomplished using the nanocomposite as an adsorbent. The actual and theoretical adsorption capacity values for both dyes at all doses were closely matched, which supported the adsorption kinetics data that fit the pseudo-first order rate model well. The adsorption data's correlation values (0.995 for XO and 0.98 for RhB) indicated that both dyes' Langmuir adsorption would perform well. Furthermore, the adsorption of XO and RhB dyes on the adsorbent is confirmed to be a viable reaction by the negative values of ΔGo. The enhanced adsorbent material for the removal of amphoteric and anionic dyes from waste water is the synthesized LaZnFe2O4 supported NiWO4@D400-MMT@CMS/MMA nanocomposites, which exhibits a reusability affinity of up to five cycles.

Recent progress in magnetic polydopamine composites for pollutant removal in wastewater treatment

Various water pollution issues pose a significant threat to human water safety. Magnetic polydopamine composites (MPCs), which can be separated by magnetic fields after the adsorption process, exhibit outstanding adsorption capacity and heterogeneous catalytic properties, making them promising materials for water treatment applications. In particular, by modifying the polydopamine (PDA) coating, MPCs can acquire enhanced high reactivity, antibacterial properties, and biocompatibility. This also provides an attractive platform for further fabrication of hybrid materials with specific adsorption, catalytic, antibacterial, and water-oil separation capabilities. To systematically provide the background knowledge and recent research advances in MPCs, this paper presents a critical review of MPCs for water treatment in terms of both structure and mechanisms of effect in applications. Firstly, the impact of different PDA positions within the composite structure is investigated to summarize the optimization of properties contributed by PDA when acting as the shell, core, or bridge. The roles of various secondary modifications of magnetic materials by PDA in addressing water pollution problems are explored. It is anticipated that this work will be a stimulus for further research and development of magnetic composite materials with real-world application potential.

Photocatalytic degradation of chlorpyrifos using Ag nanoparticles-doped g-C3N5 decorated with dendritic CdS

In this work, g-C3N5/CdS dendrite/AgNPs nanocomposite was synthesized using a mixed method consisting of hydrothermal, ultrasonic and chemistry reduction with sodium borohydride. The characterization of the as-prepared nanocomposite was done using infrared spectroscopy, X-ray, scanning electron microscopy, transmission electron microscopy, BET, and DRS methods was performed. The DRS results showed that the g-C3N5/CdS dendrite/AgNPs nanocomposite nanocomposite has a band gap of 1.08 eV. This band gap indicates the good capability of this nanocomposite as a photocatalyst. Accordingly, the photocatalytic degradation of chlorpyrifos (CPS) in was performed in an aqueous solution of the synthesized nanocomposite. The results showed that almost 95.3% of this poison, a concentration of 50 mg L-1 was degraded in the presence of 0.05 g L-1 of nanocomposite at pH = 5 in a 60 min. Hydroxide radicals and holes play a significant role in the photocatalytic process. The reusability of the nanocomposite with excellent performance in the degradation of photocatalytic toxins caused by the reduction in the electron-hole recombination and the high surface area of the nanocomposite are among the unique features of this work.

Innovative Antibacterial, Photocatalytic, Titanium Dioxide Microstructured Surfaces Based on Bacterial Adhesion Enhancement

Bacterial colonization and biofilm formation are found on nearly all wet surfaces, representing a serious problem for both human healthcare and industrial applications, where traditional treatments may not be effective. Herein, we describe a synergistic approach for improving the performance of antibacterial surfaces based on microstructured surfaces that embed titanium dioxide nanoparticles (TiO₂ NPs). The surfaces were designed to enhance bacteria entrapment, facilitating their subsequent eradication by a combination of UVC disinfection and TiO₂ NPs photocatalysis. The efficacy of the engineered TiO₂-modified microtopographic surfaces was evaluated using three different designs, and it was found that S2-lozenge and S3-square patterns had a higher concentration of trapped bacteria, with increases of 70 and 76%, respectively, compared to flat surfaces. Importantly, these surfaces showed a significant reduction (99%) of viable bacteria after just 30 min of irradiation with UVC 254 nm light at low intensity, being sixfold more effective than flat surfaces. Overall, our results showed that the synergistic effect of combining microstructured capturing surfaces with the chemical functionality of TiO₂ NPs paves the way for developing innovative and efficient antibacterial surfaces with numerous potential applications in the healthcare and biotechnology market.

Synthesis and Characterization of SPIONs Encapsulating Polydopamine Nanoparticles and Their Test for Aqueous Cu2+ Ion Removal

The removal of pollutants, such as heavy metals, aromatic compounds, dyes, pesticides and pharmaceuticals, from water is still an open challenge. Many methods have been developed and exploited for the purification of water from contaminants, including photocatalytic degradation, biological treatment, adsorption and chemical precipitation. Absorption-based techniques are still considered among the most efficient and commonly used approaches thanks to their operational simplicity. In recent years, polydopamine-coated magnetic nanoparticles have emerged for the uptake of heavy metals in water treatment, since they combine specific affinity towards pollutants and magnetic separation capacity. In this context, this work focuses on the synthesis of polydopamine (PDA)-coated Super Paramagnetic Iron Oxide Nanoparticles (PDA@SPIONs) as adsorbents for Cu²⁺ ions, designed to serve as functional nanostructures for the removal of Cu²⁺ from water by applying a magnetic field. The synthetic parameters, including the amount of SPIONs and PDA, were thoroughly investigated to define their effects on the nanostructure features and properties. Subsequently, the ability of the magnetic nanostructures to bind metal ions was assessed on Cu²⁺-containing solutions. A systematic investigation of the prepared functional nanostructures was carried out by means of complementary spectroscopic, morphological and magnetic techniques. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) measurements were performed in order to estimate the Cu²⁺ binding ability. The overall results indicate that these nanostructures hold great promise for future bioremediation applications.

Bacterial cellulose flakes loaded with Bi2MoO6 nanoparticles and quantum dots for the photodegradation of antibiotic and dye pollutants

Effective strategies to improve charge separation in semiconductor particles are critical for improving the photodegradation of organic pollutants at levels sufficient for environmental applications. Herein, Bi₂MoO₆ (BMO_MOF), comprising both nanoparticles (NPs) and quantum dots (QDs), was synthesized from a bismuth-based metal-organic framework (Bi-MOF) precursor. Surface defects on BMO_MOF, the combination of NPs and QDs, and modified energy band edges improved photogenerated charge separation and facilitated redox reactions. When compared to BMO derived from uncoordinated Bi, the BMO_MOF photocatalyst (PC) was more efficient at photodegrading tetracycline hydrochloride (TCH) and ciprofloxacin (CIP), two widely-used antibiotics ubiquitous in wastewater, as well as the carcinogenic pollutant rhodamine B (RhB). BMO_MOF was then loaded on the biopolymer bacterial cellulose (BC) to further enhance photocatalytic performance and facilitate the recovery of the PC after water treatment processes. The novel BMO_MOF/BC photocatalytic flakes were significantly larger than pure BMO_MOF, and thus easier to recuperate. Furthermore, anchoring BMO_MOF on BC flakes augmented significantly the photodegradation of TCH, CIP, and RhB, mainly because hydroxyl groups in BC act as hole traps facilitating photogenerated electron-hole separation. Results obtained with BMO_MOF/BC highlight promising approaches to develop optimal PCs for aqueous pollutants degradation.

Photocatalytic Investigation of Aerosol-Assisted Atmospheric Pressure Plasma Deposited Hybrid TiO2 Containing Nanocomposite Coatings

We report on the aerosol-assisted atmospheric-pressure plasma deposition onto a stainless-steel woven mesh of a thin nanocomposite coating based on TiO2 nanoparticles hosted in a hybrid organic−inorganic matrix, starting from nanoparticles dispersed in a mixture of hexamethyldisiloxane and isopropyl alcohol. The stainless-steel mesh was selected as an effective support for the possible future technological application of the coating for photocatalytically assisted water depollution. The prepared coatings were thoroughly investigated from the chemical and morphological points of view and were demonstrated to be photocatalytically active in the degradation of an organic molecule, used as a pollutant model, in water upon UV light irradiation. In order to optimize the photocatalytic performance, different approaches were investigated for the coating’s realization, namely (i) the control of the deposition time and (ii) the application of a postdeposition O2 plasma treatment on the pristine coatings. Both strategies were found to be able to increase the photocatalytic activity, and, remarkably, their combination resulted in a further enhancement of the photoactivity. Indeed, the proposed combined approach allowed a three-fold increase in the kinetic constant of the degradation reaction of the model dye methylene blue with respect to the pristine coating. Interestingly, the chemical and morphological characterizations of all the prepared coatings were able to account for the enhancement of the photocatalytic performance. Indeed, the presence of the TiO2 nanoparticles on the outmost surface of the film confirmed the accessibility of the photocatalytic sites in the nanocomposite and reasonably explained the enhanced photocatalytic performance. In addition, the sustained photoactivity (>5 cycles of use) of the nanocomposites was demonstrated.

Titanium dioxide nanoparticles: Recent progress in antimicrobial applications

For decades, the antimicrobial applications of nanoparticles (NPs) have attracted the attention of scientists as a strategy for controlling the ever-increasing threat of multidrug-resistant microorganisms. The photo-induced antimicrobial properties of titanium dioxide (TiO₂ ) NPs by ultraviolet (UV) light are well known. This review elaborates on the modern methods and antimicrobial mechanisms of TiO₂ NPs and their modifications to better understand and utilize their potential in various biomedical applications. Additional compounds can be grafted onto TiO₂ nanomaterial, leading to hybrid metallic or non-metallic materials. To improve the antimicrobial properties, many approaches involving TiO₂ have been tested. The results of selected studies from the past few years covering the most recent trends in this field are discussed in this review. There is extensive evidence to show that TiO₂ NPs can exhibit certain antimicrobial features with disputable roles of UV light. Hence, they are effective in treating bacterial infections, although the majority of these conclusions came from in vitro studies and in the presence of some additional nanomaterials. The methods of evaluation varied depending on the nature of the research while researchers incorporated different techniques, including determining the minimum inhibitory concentration, cell count, and using disk and well diffusion methods, with a noticeable indication that cell count was the most and dominant criterion used to evaluate the antimicrobial activity. This article is categorized under: Nanotechnology Approaches to Biology > Nanoscale Systems in Biology Therapeutic Approaches and Drug Discovery > Emerging Technologies Therapeutic Approaches and Drug Discovery > Nanomedicine for Infectious Disease.

Performance for Fly Ash Reinforced HDPE Composites over the Ageing of Material Components

The by-product abundances of fly ash allow them to be used as the reinforcing filler for high-volume and high-performance thermoplastic composites. However, the durability of the composites remains questioned as polymer degradation during environmental weathering creates brittle materials, leading to surface cracks, which potentially release hazardous fly ash particles into the environment. This paper reports the effect of environmental ageing (UV and moisture exposure) on the morphological and mechanical properties of fly ash mixed high-density polyethylene (FA/HDPE) composites with three dissimilar weight fractions (5, 10 and 15 wt%) of filler and compared the results with similarly aged neat HDPE samples. The consequence of environmental ageing on the elevated mechanical properties of composites is investigated. Fifteen wt% fly ash reinforced composite appears to have better morphological and mechanical properties after 20 weeks of ageing, with only ~5 and ~9% reduction in Young’s modulus and tensile strength, respectively. The driving factors controlling the ageing effects are broadly discussed and recommendations are made for research advancements.

Challenges and Opportunities of Using Titanium Dioxide Photocatalysis on Cement-Based Materials

Since the early seventies with the work of Akira Fujishima on photocatalytic and superhydrophilic properties of titanium dioxide (TiO2), also known as the Honda–Fujishima effect, photocatalysis has been investigated and progressively implemented in cement-based materials towards the development of self-cleaning, air-purifying and antiseptic materials, buildings and infrastructure. Although important achievements have been obtained at the laboratory scale, their real scale application has had some limitations mainly due to the low efficiencies obtained during adverse environmental conditions. Therefore, this article presents the challenges and opportunities of using of titanium dioxide in cement-based materials towards the development of truly efficient sustainable building materials. First, TiO2 photocatalysis and its incorporation in cementitious materials are presented. Second, self-cleaning, air-purifying and antimicrobial properties are discussed in terms of the lab and pilot project results. Third, conclusions regarding the different multifunctional properties are given towards the real application of TiO2 photocatalysis. Particularly, complementary technologies and strategies are presented in order to increase the above-mentioned multifunctional properties.

Potential Applications of Geopolymer Cement-Based Composite as Self-Cleaning Coating: A Review

Nowadays, concepts of self-cleaning have received great attention in construction building materials. Self-cleaning with the presence of photocatalyst has been applied in building materials to overcome the problem of building surfaces becoming dirty after exposure for a long time in highly polluted areas. To date, the concept of green blending materials has led to the development of a new binding material for green materials, which is geopolymer with an addition of photocatalyst. This review focused on the development of conventional self-cleaning paste, including the method of preparation and the impact of adding photocatalyst on physical and mechanical properties. However, although self-cleaning has been widely applied in conventional cement paste, its applications in geopolymers are still in the early stages of development and require more research. Therefore, this paper also intended to review the current knowledge on properties of geopolymer cement-based composite and its potential to be applied as a self-cleaning coating.

Tuning the surface and optical properties of graphitic carbon nitride by incorporation of alkali metals (Na, K, Cs and Rb): Effect on photocatalytic removal of organic pollutants

Alkali metals have been known for their intercalation properties and can be employed for the separation of stacking in sheet-like materials. In this work, alkali metals (Na, K, Rb and Cs) have been systematically incorporated in varying concentrations in g-C₃N₄ sheets and their effect on resulting optical, surface and photocatalytic properties have been explored in detail. It was observed that the optical, electronic and surface properties of g-C₃N₄ were altered upon the incorporation of different alkali metal ions. The band gap and specific surface area of resulting materials were decreased as compared to the pristine g-C₃N₄. In addition, the alkali metal incorporation in g-C₃N₄ sheets showed the formation of cyanide groups and nitrogen vacancies in the resulted materials. Further, the photocatalytic activity of g-C₃N₄ and alkali metal incorporated g-C₃N₄ was calculated by studying the degradation of acid red 94 dye under visible light irradiation. It was observed that the photocatalytic activity of pristine g-C₃N₄ sheets was decreased with an increase in the concentration of alkali salt used during the synthesis of alkali metal incorporated g-C₃N₄. This decrease in the activity could arise due to the decreased surface area, detrimental amount of nitrogen vacancies and high concentration of alkali metal ions incorporated in the structural framework of g-C₃N₄ sheets. This work provides a unique example of the adverse effect of alkali metal ions on photocatalytic activity of g-C₃N₄ and paves future directions for the improvement of the performance of g-C₃N₄ based materials.

Preparation of a composite coating film via vapor induced phase separation for air purification and real-time bacteria photocatalytic inactivation

Infectious diseases resulted from transmitting of bacteria or virus like COVID-19 via air-borne droplets have brought severe threat to human beings worldwide. Cutting the spreading paths to obtain clean air is one of the promising strategies to prevent people from such dangerous diseases. In this work, we have employed a strategy of spray coating in combination with vapor induced phase separation to prepare a composite coating film to fulfill that purpose. A stable mixture suspension containing micelles of block copolymer of poly(styrene-block-butadiene-block-styrene) and TiO₂ nanoparticles was sprayed onto stainless steel mesh to evaporate solvent in non-solvent vapor atmospheres. A water vapor atmosphere and an ethanol vapor atmosphere were in turn employed to improve the mechanical strength of the obtained coating film. The porous microstructure, the porosity, and the superhydrophobicity of the coating film were carefully characterized and analyzed. The air pressure-drop of the coating film was determined to be lower than 100 Pa, indicating a high air permeability. Moreover, a foggy air containing E. coli was pressed through the coating film via a home-made apparatus to simulate the air purification system, where E. coli contained air-borne droplets were intercepted by the film matrix in a physical manner, and the bacteria was photocatalytically inactivated at the meantime. A filtration efficiency of 99.7% and a 99.6% efficiency of real-time photocatalytic inactivation of E. coli demonstrate the promising potential of the coating film.

Synthesizing and Evaluating the Photocatalytic and Antibacterial Ability of TiO2/SiO2 Nanocomposite for Silicate Coating

The TiO₂/SiO₂ nanocomposite has been synthesized by a sol-gel method and investigated the effect of the SiO₂ content (0, 5, 10, 15, 20, and 50%) on the rutile-to-anatase phase transition of TiO₂ NPs. In order to increase the photocatalytic efficiency of the nanocomposite and decrease the price of material, the TiO₂/SiO₂ Nc with content SiO₂ of 15% sample is chosen for preparing silicate coating. The efficiency of photocatalytic MB and antibacterial ability in the air of W silicate coating (adding TiO₂/SiO₂ Nc (15%)) achieve almost 100% for 60 h and 94.35% for 3 h, respectively. While the efficiency of photocatalytic MB and antibacterial ability of WO silicate coating (adding commercial TiO₂/SiO₂) is about 25–30% for 60 h and 6.02% for 3 h, respectively. The presence of TiO₂/SiO₂ Nc (15%) with a larger surface area in W silicate coating can provide increased centers for absorption, photocatalytic reaction, and the contact between sample and bacteria lead to enhance the photocatalytic and antibacterial ability of W silicate coating.

Removal of methylene blue dye using nano zerovalent iron, nanoclay and iron impregnated nanoclay - a comparative study

There has been an increasing challenge from the emission of methylene blue (MB) dye-containing wastewater and its management methods in industry. The sorption process is one conventionally used method. In this study, nanoclay, nano zero valent iron (nZVI), and iron impregnated nanoclay were prepared and studied for the removal of MB dye in batch mode. The effects of operating parameters like pH, dye concentration, sorbent dosage, and contact time were investigated and optimized. The nZVI, nanoclay, and iron impregnated nanoclay sorbents showed zeta potentials of -32.1, -53.4, and -40.7 mV, respectively. All the nano adsorbents were crystalline. The nanoclay was characterized by an average surface area, pore volume and pore diameter of 43.49 m2 g-1, 0.104 cm3 g-1 and 2.806 nm, respectively. nZVI showed a surface area of 47.125 m2 g-1, pore volume of 0.119 cm3 g-1, and pore diameter of 3.291 nm. And iron impregnated nanoclay showed a surface area of 73.110 m2 g-1 with a pore volume of 15 cm3 g-1 and a pore diameter size of 3.83 nm. A Langmuir EXT nitrogen gas adsorption isotherm (R 2 ∼ 0.99) was the best fit. The thermodynamics parameters, such as ΔG° (-12.64 to -0.63 kJ mol-1), ΔH° (+0.1 to +62.15 kJ mol-1) and ΔS° (+0.10 to +0.22 kJ mol-1), confirmed that a spontaneous and endothermic adsorption process took place at a high rate of disorder. Iron impregnated nanoclay showed higher negative Gibbs free energy (-12.64 kJ mol-1), higher enthalpy change (+62.5 kJ mol-1) and entropy (+0.22 kJ mol-1) and gave a better MB removal performance. In addition, the lower negative heat of enthalpy for all adsorptions proved the dominance of physisorption. The methylene blue adsorption isotherm on nZVI and nanoclay showed the best fit with the Freundlich isotherm model with correlation coefficients (R 2) ∼0.98 and 0.99, respectively. Whereas the Langmuir adsorption isotherm was the best fit for iron impregnated nanoclay (R 2 ∼ 0.98). The adsorption activities of nZVI, nanoclay and iron impregnated nanoclay were fitted to a pseudo-second-order kinetic model with correlation coefficients (R 2) of 0.999, 0.997 and 0.983, respectively. The optimal pH 7.0 (RE: 99.1 ± 0.73%), initial MB concentration 40 ppm (RE: 99.9 ± 0.03%), contact time 120 min (RE: 99.9 ± 0.9%), and adsorbent dose 80 (99.9 ± 0.03%) were obtained for iron impregnated nanoclay. The optimal operational parameters of nanoclay and nZVI, respectively, were pH 11.0 and 13.0, initial MB concentration 20 and 20 ppm, adsorbent dose 100 and 140 mg, and contact time 120 and 140 min. In general, iron impregnated nanoclay has shown promising cationic dye adsorbance for industrial applications; but a recyclability test is suggested before scale-up.

Evaluation of the Photocatalytic Activity and Anticorrosion Performance of Electrospun Fibers Doped with Metallic Oxides

This paper reports the development and characterization of a multifunctional coating that combines anticorrosion and photocatalytic properties, deposited by means of the electrospinning technique. In the first step, a functional electrospun fiber mat composed of poly(acrylic acid) (PAA) and β-cyclodextrin (β-CD) was obtained, showing high water insolubility and great adhesion increased by means of a thermal crosslinking process (denoted as PAA + β-CD). In the second step, the fibers were doped with particles of titanium dioxide (denoted as PAA + β-CD/TiO₂) and titanium dioxide plus iron oxide (denoted as PAA + β-CD/TiO₂/Fe₂O₃). The morphology and fiber diameter of the electrospun mats were evaluated by using confocal microscopy, whereas the presence of the metal oxides in the electrospun fibers was corroborated by scanning electron microscopy (SEM) and X-ray fluorescence (XRF), respectively. In addition, electrochemical tests in saline solution revealed that the sample composed of PAA + β-CD/TiO₂/Fe₂O₃ showed the highest corrosion protection efficiency of all the samples, which was directly associated to lower corrosion current density and higher corrosion potential. Furthermore, the paper reports a novel approach to in situ determination of methylene blue (MB) degradation onto the coating. The results revealed complete degradation of MB, which is perfectly appreciated by total discoloration of the film in the irradiated zone (from bluish to a white spot). The main conclusions of this research are the efficiency of the electrospun system PAA + β-CD/TiO₂/Fe₂O₃ for developing photocatalytic activity and corrosion protection and the utility of the dry MB discoloration tests to evaluate photocatalytic activity.

Controllable synthesis and characterization of Mg2SiO4 nanostructures via a simple hydrothermal route using carboxylic acid as capping agent and their photocatalytic performance for photodegradation of azo dyes

Magnesium silicate (forsterite) nanoparticles were synthesized by a facile hydrothermal method, and characterized using several techniques such as XRD, SEM, EDS, DRS, Raman, TEM, and FT-IR. Several carboxylic acid structures were applied to modify the morphology and surface properties of the as-prepared particles. In this manuscript, citric acid, maleic acid, and succinic acid were used as the carboxylic acid agents. The effect of changing the ratio of carboxylic acid agent to central metal on the morphology and photocatalytic behavior was evaluated. The activities of the Mg₂SiO₄ nanostructures as photocatalysts were assessed by the degradation of several azo dyes (Acid Blue 92, Acid Brown 14, and Acid Violet 7) under UV and Vis light irradiation. The degradation percentages of Acid Blue 92 were about 88% and 74% in the presence of Vis and UV light respectively, and the percentages for photodegradation of Acid Brown 14 were approximately 76% and 82% in the presence of Vis and UV light, respectively. Furthermore, the degradation percentages for Acid Violet 7 were 93% and 80% under UV and Vis light, respectively.

Mg₂SiO₄ nanostructures have been synthesized via a facile hydrothermal approach. The photocatalytic behavior of Mg₂SiO₄ nanostructures prepared by different carboxylic acids have been investigated to degrade azo dyes under UV and visible light.

Future directions of catalytic chemistry

The philosophy of sustainable development is prevailing worldwide, and will probably bring about a society revolution trend in the future. Catalytic chemistry will play a crucial role in sustainable economic development since at least a catalytic process is involved in almost all-important areas of chemical industry, such as synthesis of chemicals and materials, energy production and conversion as well as pollution abatement and environmental protection. In this paper, we attempt to summarize three common critical directions for catalysis research, in order to meet future needs for sustainable economic development. (i) The discovery of high-performance catalysts will evolve from trial-and-error to rational design. This is due to the maturing theory-experiment joint research schemes and the increasing abilities to explore dynamic nature of catalysts under reaction conditions. (ii) The catalysis for the transition of energy and chemicals generation from oil and coal to more renewable sources will be highly pursued. (iii) The catalysis for cleaner chemical processes will be another active research direction. In Sections “Sustainable catalysis for renewable fuels and chemicals” and “Ecologically clean catalytic process”, some important examples are discussed especially.

Nano zero valent iron (nZVI) particles for the removal of heavy metals (Cd2+, Cu2+ and Pb2+) from aqueous solutions

For the past 15 years, nanoscale metallic iron (nZVI) has been investigated as a new tool for the treatment of heavy metal contaminated water. The removal mechanisms depend on the type of heavy metals and their thermodynamic properties. A metal whose redox potential is more negative or close to the reduction potential of Fe(0) is removed by the reduction process, while the others will be mediated by precipitation, complexation or other sorption processes. This review summarises our contemporary knowledge of nZVI aqueous chemistry, synthesis methods, mechanisms and actions (practical experiences) of heavy metal (Cd, Cu and Pb) removal and challenges of nZVI practical applications. Its inner core (iron(0)) has reducing ability towards pollutants, while the iron oxide (FeO) outer shell provides reaction sites for chemisorption and electrostatic interactions with heavy metals. Emerging studies highlighted that nZVI surfaces will have negatively charged species at higher pH and have good affinity for the removal of positively charged species such as heavy metals. Different sizes, shapes and properties of nZVI have been produced using various methods. Ferric salt reduction methods are the most common methods to produce stable and fine graded nZVI. Higher uptake of copper(ii), lead(ii) and cadmium(ii) has also been reported by various scholars. Practical pilot tests have been conducted to remove heavy metals, which gave highly satisfactory results. Challenges such as agglomeration, sedimentation, magnetic susceptibility, sorption to other fine materials in aqueous solution and toxicity of microbiomes have been reported. Emerging studies have highlighted the prospects of industrial level application of nano zero valent particles for the remediation of heavy metals and other pollutants from various industries.

Carbon quantum dots-TiO2 nanocomposite as an efficient photocatalyst for the photodegradation of aromatic ring-containing mixed VOCs: An experimental and DFT studies of adsorption and electronic structure of the interface

In this work, we have developed and optimized TiO₂ nanoparticles decorated with carbon quantum dots to examine its potential use in the photocatalytic oxidation of aromatic ring containing gas-phase mixed volatile organic compounds, e.g., benzene, toluene, and p-xylene. Carbon quantum dots decorated TiO₂ demonstrated good photodegradation efficiency in contrast to pure TiO₂ under UV-vis light illumination. For example, with 0.5 wt% carbon quantum dots decorated on TiO₂, 64 % of the mixed volatile organic compounds were photodegraded, while pure TiO₂ only exhibited 44 % of the photodegradation efficiency. Also, the carbon quantum dots (0.5 wt%)/TiO₂ nanocomposite demonstrated considerable photocatalytic activity within the visible region. On the other hand, pure TiO₂ remained inactive within the visible region. The density functional theory study of the carbon quantum dots/TiO₂ interface revealed that C 2p states of carbon quantum dots incorporated new energy states around the Fermi level near the lowest conduction band. This might be accountable for the improved charge separation process and better conductivity of the photogenerated electrons. The improved photocatalytic performance of the carbon quantum dots/TiO₂ nanocomposites can be attributed to good light harvesting within the UV-vis region, charge separation, and adsorption capability.

Photocatalytic activity of undoped and Mn- and Co-doped TiO2 nanocrystals incorporated in enamel coatings on stainless steel

New catalysts composed of undoped and transition metal-doped TiO2 nanocrystals incorporated in enamels on stainless steel show potential applications for pollutant photodegradation.

Treatment of Water Contaminated with Reactive Black-5 Dye by Carbon Nanotubes

Most of the dyes used today by the textile industry are of synthetic origin. These substances, many of which are highly toxic, are in many cases not adequately filtered during the processing stages, ending up in groundwater and water courses. The aim of this work was to optimize the adsorption process of carbon nanotubes to remove an azo-dye, called Reactive Black-5, from aqueous systems. Particular systems containing carbon nanotubes and dye solutions were analyzed. Furthermore, the reversibility of the process and the presence of possible degradation phenomena by the dye molecules were investigated. For this purpose, the influence of different parameters on the adsorption process, such as the nature of the carbon nanotubes (purified and nonpurified), initial concentration of the dye, stirring speed, and contact times, were studied. The solid and liquid phases after the tests were characterized by chemical-physical techniques such as thermogravimetric analysis (TG, DTA), UV spectrophotometry, BET (Brunauer, Emmett, Teller), and TOC (total organic carbon) analysis. The data obtained showed a high adsorbing capacity of carbon nanotubes in the removal of the Reactive Black-5 dye from aqueous systems. Furthermore, the efficiency of the adsorption process was observed to be influenced by the stirring speed of the samples and the contact time, while purified and nonpurified nanotubes provided substantially the same results.

Photocatalytic TiO2-Based Nanostructured Materials for Microbial Inactivation

Pathogenic microorganisms can spread throughout the world population, as the current COVID-19 pandemic has dramatically demonstrated. In this scenario, a protection against pathogens and other microorganisms can come from the use of photoactive materials as antimicrobial agents able to hinder, or at least limit, their spreading by means of photocatalytically assisted processes activated by light—possibly sunlight—promoting the formation of reactive oxygen species (ROS) that can kill microorganisms in different matrices such as water or different surfaces without affecting human health. In this review, we focus the attention on TiO2 nanoparticle-based antimicrobial materials, intending to provide an overview of the most promising synthetic techniques, toward possible large-scale production, critically review the capability of such materials to promote pathogen (i.e., bacteria, virus, and fungi) inactivation, and, finally, take a look at selected technological applications.

ON/OFF Switchable Nanocomposite Membranes for Separations

Although water, air, and other resources are abundant on earth, they have been subjected to strict environmental regulations. This is because of their limitation of availability for human consumption. In the separation industry, the membrane system was introduced to increase the amount of resources available to mankind. Experts used an easy-to-use polymeric material to design several membranes with porous structures for wastewater treatment, gas separation, and chemical removal; consequently, they succeeded in obtaining positive results. However, past polymeric membranes exhibited a chronic drawback such that it was difficult to simultaneously augment the permeate flux and improve its selectivity toward certain substances. Because of the trade-off relationship that existed between permeability and selectivity, the membrane efficiency was not very good; consequently, the cost-effectiveness was significantly hindered because there was no other alternative than to replace the membrane in order to maintain its initial characteristics steadily. This review begins with the introduction of a polymer nanocomposite (PNC) membrane that has been designed to solve the chronic problem of polymeric membranes; subsequently, the stimuli-responsive PNC membrane is elucidated, which has established itself as a popular topic among researchers in the separation industry for several decades. Furthermore, we have listed the different types and examples of stimuli-responsive PNC membranes, which can be switched by external stimuli, while discussing the future direction of the membrane separation industry.

Heterogeneous Photocatalysis Scalability for Environmental Remediation: Opportunities and Challenges

Heterogeneous photocatalysis is an ecofriendly technique for purifying organic pollutants in environmental systems. While pilot-scale photoreactors have explored photocatalytic system upscalibility, their practical implementation is restricted for various reasons. These include feed composition alteration, complicated photoreactor designs, high operation and synthesis costs, photocatalyst poisoning, low quantum yield under solar irradiation, fast exciton recombination, and low reuse or regeneration capabilities. In this paper, we highlight the photocatalyst scalability challenges for real-world applications. We also provide an in-depth discussion on photocatalyst opportunities for effective air and water pollution control. Lastly, we offer a contemporary perspective on photocatalysis scale-up for the real environmental treatment.

Origin of photocatalytic activity enhancement in Pd/Pt-deposited anatase N-TiO2- experimental insights and DFT study of the (001) surface

In pursuit of the ideal photocatalyst, cheap and stable semiconductor TiO₂ is considered to be a good choice if one is able to reduce its band gap and decrease the recombination rate of charge carriers. The approach that offers such improvements for energy conversion applications is the modification of TiO₂ with nitrogen and noble metals. However, the origin of these improvements and possibilities for further design of single-atom catalysts are not always straightforward. To shed light on the atomic-scale picture, we modeled the nitrogen-doped (001) anatase TiO₂ surface as a support for palladium and platinum single-atom deposition. The thermodynamics of various synthesis routes for Pd/Pt deposition and nitrogen doping is considered based on density functional theory (DFT)-calculated energies, highlighting the effect of nitrogen doping on metal dimer formation and metal-support interaction. XPS analysis of the valence band of the modified TiO₂ nanocrystals, and the calculated charge transfer and electronic structure of single-atom catalysts supported on the (001) anatase TiO₂ surface provide an insight into modifications occurring in the valence zone of TiO₂ due to nitrogen doping and Pd/Pt deposition at the surface. DFT results also show that substitutional nitrogen doping significantly increases metal-support interaction, while interstitial nitrogen doping promotes only Pt-support interaction.

Low Temperature Synthesis of Photocatalytic Mesoporous TiO2 Nanomaterials

We report the synthesis of mesoporous TiO2 nanostructures based on the decomposition of TiOSO4 in aqueous alkaline solution at room temperature, followed by mild thermal treatment (110 °C) in an oven and suitable to yield up to 40 g of product per batch. The duration of the thermal treatment was found to be crucial to control crystalline phase composition, specific surface area, surface chemistry and, accordingly, the photocatalytic properties of the obtained TiO2 nanocrystals. The thorough investigation of the prepared samples allowed us to explain the relationship between the structure of the obtained nanoparticles and their photocatalytic behavior, that was tested in a model reaction. In addition, the advantage of the mild treatment against a harsher calcination at 450 °C was illustrated. The proposed approach represents a facile and sustainable route to promptly access an effective photocatalyst, thus holding a significant promise for the development of solutions suitable to real technological application in environmental depollution.

Adsorption of Reactive Blue 116 Dye and Reactive Yellow 81 Dye from Aqueous Solutions by Multi-Walled Carbon Nanotubes

The multi-walled carbon nanotubes obtained by catalytic chemical vapour deposition synthesis are used as a solid matrix for the adsorption of the Reactive Blue 116 dye and the Reactive Yellow 81 dye from aqueous solutions at different pH values. The batch tests carried out allowed us to investigate the different effects of pH (2, 4, 7, 9 and 12) and of the contact time (2.5 ÷ 240 min) used. The liquid phase was analysed using ultraviolet-visible spectrophotometry in order to characterise the adsorption kinetics, the transport mechanisms and the adsorption isotherms. The adsorption of the optimal dye was observed at pH 2 and 12. The pseudo-first order kinetic model provided the best approximation of experimental data compared to the pseudo-second order kinetic model. The predominant transport mechanism investigated with the Weber and Morris method was molecular diffusion for both Reactive Yellow 81 and Reactive Blue 116, and the equilibrium data were better adapted to the Langmuir isothermal model. The maximum adsorption capacity for Reactive Yellow 81 and Reactive Blue 116 occurred with values of 33.859 mg g^-1 and 32.968 mg g^-1, respectively.

X-ray ptychographic mode of self-assembled CdSe/CdS octapod-shaped nanocrystals in thick polymers

This work describes the application of X-ray ptychography for the inspection of complex assemblies of highly anisotropic nanocrystals embedded in a thick polymer matrix. More specifically, this case deals with CdSe/CdS octapods, with pod length L = 39 ± 2 nm and pod diameter D = 12 ± 2 nm, dispersed in free-standing thick films (24 ± 4 µm) of polymethyl methacrylate and polystyrene, with different molecular weights. Ptychography is the only imaging method available to date that can be used to study architectures made by these types of nanocrystals in thick polymeric films, as any other alternative direct method, such as scanning/transmission electron microscopy, can be definitively ruled out as a result of the large thickness of the free-standing films. The electron density maps of the investigated samples are reconstructed by combining iterative difference map algorithms and a maximum likelihood optimization algorithm. In addition, post image processing techniques are applied to both reduce noise and provide a better visualization of the material morphological details. Through this process, at a final resolution of 27 nm, the reconstructed maps allow us to visualize the intricate network of octapods inside the polymeric matrices.

Integrating adsorption and photocatalysis: A cost effective strategy for textile wastewater treatment using hybrid biochar-TiO2 composite

TiO₂ based photocatalysts are extensively used for textile wastewater treatment as they are ecofriendly, inexpensive, easily available, nontoxic and have higher photostabililty. However, their wider band gap, charge carrier's recombination, and utilization of light absorbance limits their performance. In the present work, a hybrid biochar-TiO₂ composite (BCT) has been synthesized by a facile synthesis strategy to overcome these problems. These photocatalysts are characterized using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), Fourier Transform Infrared (FTIR), UV-vis diffuse reflectance spectra (DRS), and photoluminescence (PL) to evaluate their crystallinity, morphology, functional groups, bandgap energy and charge separation properties, respectively. The photodegradation of simulated textile wastewater is analyzed using hybrid composites. The hybrid biochar-TiO₂ composite showed higher charge separation, slow recombination of electron-hole pairs, and enhanced light absorption as compared to control (pure TiO₂ and BC alone). 99.20 % photodegradation efficiency of dye-simulated wastewater is achieved employing optimum hybrid composite, while the pure biochar and TiO₂ samples exhibits 85.20 % and 42.60 % efficiencies, respectively. The maximum adsorption capacity is obtained for hybrid biochar-TiO₂ sample, 74.30 mgg^-1 in comparison to biochar (30.40 mgg^-1) and pure TiO₂ (1.50 mgg^-1). The results show that hybrid biochar-TiO₂ composites can perform in the target application of organic industrial pollutant removal.

The NOx Degradation Performance of Nano-TiO2 Coating for Asphalt Pavement

The NO_x degradation performance of nano-TiO₂ as a coating material for the road environment was evaluated in this research. The nano-TiO₂ coating materials for both road surface and roadside were prepared by using anatase nano-TiO₂, activated carbon powder, silane coupling agent and deionized water. The impact of varying amounts of coating material and silane coupling agent were evaluated. The road environment of NO_x degradation was simulated by the photocatalytic test system designed by the research team. For the road surface coating, the photocatalytic degradation experiments of NO under different radiation intensities were carried out. The results show that the material has good photocatalytic degradation performance, and the proper amount of silane coupling agent can enhance the bonding performance of the material and asphalt mixture. For the roadside coating, sodium dodecylbenzene sulfonate was selected as the surfactant to carry out the photocatalytic degradation experiment of NO₂ with different dosages of surfactant. The results showed that when the mass ratio of nano-TiO₂ and surfactant was about 1:2, the catalytic degradation effect of the material was the best.

Highly efficient photocatalytic performance of BiI/Bi2WO6 for degradation of tetracycline hydrochloride in an aqueous phase

A series of novel BiI/Bi₂WO₆ nanosheets was successfully synthesized using a simple and efficient one-step hydrothermal method; the obtained specimens were subsequently characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, ultraviolet-visible spectrophotometry, X-ray photoelectron spectroscopy, N₂ adsorption/desorption isotherms, Raman spectroscopy, ultraviolet-visible spectroscopy, Fourier-transform infrared spectroscopy, photoluminescence, and electronic impedance spectroscopy testing. The results indicated that the photocatalytic performance of the BiI/Bi₂WO₆ composites for the degradation of tetracycline hydrochloride (TC) from aqueous media under visible light irradiation (λ > 420 nm) was higher than that of pure Bi₂WO₆. The 0.8I-BiI/BWO composite (where 0.8 is the I : W molar ratio) presented the best photocatalytic performance of all analyzed specimens, and was able to degrade approximately 90% of the TC in 80 min. In addition, radical-capture experiments have demonstrated that superoxide anion radicals and hydroxyl radicals were the main active species for degrading organic pollutants, and a photocatalytic mechanism for the BiI/Bi₂WO₆ system was proposed. This study not only provides a method for the simple preparation of BiI/Bi₂WO₆, but could also present important implications for ecological risk management and prevention against antibiotic pollution.

This study provides a method for the simple preparation of BiI/Bi₂WO₆, and present important implications for prevention against antibiotic pollution.

Morphology-controllable synthesis and application of TiO2 nanotube arrays with “photocatalysis and self-cleaning” synergism

The integration of photocatalytic materials and self-cleaning superhydrophobic materials provides a possibility of combining decontamination and antifouling.

Low-Cost Synthesis of Cu-Modified Immobilized Nanoporous TiO2 for Photocatalytic Degradation of 1H-Benzotriazole

Cu-modified immobilized nanoporous TiO2 photocatalysts, prepared by electrochemical anodization of titanium foils, were obtained via four different synthesis methods: hydrothermal synthesis, anodization with Cu source, electrodeposition, and spin-coating, using two different copper sources, Cu(NO3)2 and Cu(acac)2. The objective of this research was to investigate how copper modifications can improve the photocatalytic activity of immobilized nanoporous TiO2 under the UV/solar light irradiation. The best photocatalytic performances were obtained for Cu-modifications using spin-coating. Therefore, the effect of irradiated catalyst surface areas on the adsorption of model pollutants, methylene blue (MB) and 1H-benzotriazole (BT), was examined for samples with Cu-modification by the spin-coating technique. The mechanisms responsible for increased degradation of MB and BT at high Cu concentrations (0.25 M and 0.5 M) and decreased degradation at low Cu loadings (0.0625 M and 0.125 M) were explained. 1H-benzotriazole was used to study the photocatalytic activity of the given samples because it is highly toxic and present in most water systems. The characterization of the synthesized Cu-modified photocatalysts in terms of phase composition, crystal structure, and morphology were investigated using X-ray Diffraction, Raman Spectroscopy, Scanning Electron Microscopy, and Energy Dispersive X-ray spectroscopy.