Novel TiO2 catalyst carriers with high thermostability for selective catalytic reduction of NO by NH3

Effect of NO2 on N2 O production and NOx emission reduction in NH3 Selective Catalytic Reduction

With the introduction of increasingly strict emission regulations, reducing nitrogen oxide (NOx ) emissions and nitrous oxide (N2 O) production from diesel engines have become the focus of research. At high temperature, the reaction of NO2 in the catalyst generates the intermediate product NH4 NO3 , which first crystallizes below 300 °C. These crystals tend to block the pores and inhibit the reaction. Subsequently, N2 O is produced through the decomposition of NH4 NO3 , leading to additional pollution. Therefore, the concentration of NO2 has a direct impact on both the NOx conversion efficiency and the generation of N2 O, requiring consideration of the optimal proportion of NO2 in SCR. Considering these two factors, it is concluded that the optimal amount of NO2 varies with temperature. To improve the NOx conversion rate of the Cu-SSZ-13 catalyst at low temperatures and reduce N2 O generation, the optimal NO2 ratio of the Cu-SSZ-13 catalyst under various operating conditions is studied using numerical simulations. As the temperature rises, the optimal NO2 /NOx ratio first increases and then decreases. Under the optimal NO2 /NOx ratio, the NOx conversion rate significantly increases, while N2 O generation decreases considerably. The optimal NO2 /NOx ratio also provides suggestions for the optimization of the DOC-DPF-DCR system.

Resource utilization of high-concentration SO2 for sulfur production over La-Ce-Ox composite oxide catalyst

Sulfur dioxide is one of the main causes of air pollution such as acid rain and photochemical smog, and its pollution control and resource utilization have become important research directions. La₂O₃ was incorporated into CeO₂ to enhance the surface basicity of La-Ce-O_x catalyst and increase the concentration of chemisorbed oxygen, thereby promoting the improvement of catalytic performance of SO₂ reduction by CO. Results have showed that the incorporation of La₂O₃ would not only increase the concentration of chemisorbed oxygen and hydroxyl on the catalyst surface, but also increase the basicity of the catalyst, thereby facilitating the adsorption of SO₂ on the catalyst surface. The 12%La-Ce-O_x was the optimal catalyst, and its SO₂ conversion at 350-400 ℃ reached close to 100%, and the sulfur yield at this temperature range was higher than 93%. Finally, according to the in situ infrared diffuse reflectance spectrum, it was found that the main reaction intermediates of 12%La-Ce-O_x in the catalytic reduction of SO₂ were weakly adsorbed sulfate, SO₃^2-, non-coordinating CO₃^2-, monodentate carbonate, and CO, so the catalytic reaction followed the L-H and E-R mechanisms simultaneously.

An overview of the deactivation mechanism and modification methods of the SCR catalysts for denitration from marine engine exhaust

Selective catalytic reduction (SCR) technology is currently the most effective deNO_x technology and has broad application prospects. Moreover, there is a large NO_x content in marine engine exhaust. However, the marine engine SCR catalyst will be affected by heavy metals, SO₂, H₂O_(g), hydrocarbons (HC) and particulate matter (PM) in the exhaust, which will hinder the removal of NO_x via SCR. Furthermore, due to the high loading operation of the marine engine and the regeneration of the diesel particulate filter (DPF), the exhaust temperature of the engine may exceed 600 °C, which leads to sintering of the SCR catalysts. Therefore, the development of new catalysts with good tolerances to the above emissions and process parameters is of great significance for further reducing NO_x from marine engines. In this work, we first elaborate on the mechanism of the SCR catalyst poisoning caused by marine engine emissions, as well as the working mechanism of SCR catalysts affected by the engine exhaust temperature. Second, we also summarize the current technologies for improving the properties of SCR catalysts with the aim of enhancing the resistance and stability under complex working conditions. Finally, the challenges and perspectives associated with the performance optimization and technology popularization of marine SCR systems are discussed and proposed further. Consequently, this review may provide a valuable reference and inspiration for the development of catalysts and improvement in the denitration ability of SCR systems matched with marine engines.

Catalytic Oxidation of Chlorobenzene over Ce-Mn-Ox/TiO2: Performance Study of the Porous Structure

Chlorobenzene (CB) is a volatile and harmful organic molecule that may result in deformities, cancer, etc. Catalytic oxidization of CB may be a way to manage it. The development of nonprecious catalysts with high catalytic activity is the key but is still a challenge. In this work, a series of Ce-Mn-Ox/TiO2 modified by citric acid monohydrate were developed and exhibited a composite pore structure. This pore structure leads to a large specific surface area, highly exposed activity sites, and excellent catalytic activity. The as-prepared 10C-CM/T exhibited nearly 100% efficiency for CB oxidization in the temperature range of 300–350 °C. The in situ DRIFT measurements demonstrated that the main intermediates at 250 °C are maleate and phenolic acid, whereas when the temperature is 350 °C, the main intermediates are carbonate, bidentate carbonate, and maleate.

Simultaneous catalytic removal of NO, mercury and chlorobenzene over WCeMnOx/TiO2-ZrO2: Performance study of microscopic morphology and phase composition

Nitrogen oxides, mercury and chlorobenzene are important air pollutants emitted by waste incineration and other industries. Coordinated control of multiple pollutants has become an important technology for air pollution control. Through solid-phase structure control, the catalytic performance of the WCeMnO_x/TiO₂-ZrO₂ catalyst for simultaneous catalytic removal of NO, mercury and simultaneous removal of NO and chlorobenzene were improved. MnWO₄ improved the solid acidity of the catalyst and improved the catalytic activity at high temperature. The formation of Ce_0·75Zr_0·25O₂, Ce₂WO₆, Ce₂Zr₂O₇ and Ce₂Ti₂O₇ improved the catalytic activity at low temperature. The presence of TiOSO₄ would affect the valence of metal ions and the reduction of chemisorbed oxygen, thereby reducing the catalytic activity at low temperature. Within the same size range of nanoparticles, cyclic nanoparticles exposed more active sites due to their hollow structure, and their catalytic performance was better than spherical nanoparticles. The thickness of the circular nanoparticles of WCM/TZ-14 catalyst was about 14 nm, and the diameter was about 40 nm Ce_0.75Zr_0.25O₂ and MnWO₄ were also present in the phase composition. Therefore, it exhibited the best performance for simultaneous catalytic removal of NO, mercury and simultaneous removal of NO and chlorobenzene. The coincidence temperature window was 347-516 °C. Finally, WCM/TZ-14 catalyst followed both E-R and L-H mechanisms in the NH₃-SCR reaction.

Understanding the roles of copper dopant and oxygen vacancy in promoting nitrogen oxides removal over iron-based catalyst surface: A collaborative experimental and first-principles study

In this work, we proposed a novel strategy of copper (Cu) doping to enhance the nitrogen oxides (NO_x) removal efficiency of iron (Fe)-based catalysts at low temperature through a simple citric acid mixing method, which is critical for its practical application. The doping of Cu significantly improves the deNO_x performance of Fe-based catalysts below 200 °C, and the optimal catalyst is (Cu_0.22Fe_1.78)_1-δO₃, which deNO_x efficiency can reach 100% at 160-240 °C. From the macro aspects, the main reasons for the excellent catalytic activity of the (Cu_0.22Fe_1.78)_1-δO₃ catalyst are the large number of oxygen vacancies (O_vac), appropriate Fe³⁺ and Cu²⁺ contents, stronger surface acidity and redox ability. From the micro aspects, the O_vac plays a key role in enhancing molecular adsorption, oxidation, and the deNO_x reaction over the Fe-based catalyst surface, which promoting order is CuO_vac > O_vac > Cu. This work provides a new insight for the mechanism study of oxygen vacancy engineering and also accelerates the development of CuFe bimetal composite catalysts at low temperature.

Effect of doping Cr on NH3 adsorption and NO oxidation over the FexOy/AC surface: A DFT-D study

Activated carbon supported iron-based catalysts (Fe_xO_y/AC) show good deNO_x efficiency at low temperature. The doping of chromium (Cr) greatly improves the catalyst activity. However, the detailed effect of doping Cr over Fe_xO_y/AC surface at molecular level is still a grey area. In this study, the roles of Cr dopant on gas adsorption and NO oxidation were deeply investigated by a DFT-D3 method. Results show that the synergy of Cr-Fe bimetal improves the binding capacity of Fe₂O₃/AC and Fe₃O₄/AC surfaces after doping Cr. NH₃ can be adsorbed on Cr and Fe sites to form coordinated NH₃. Doping Cr greatly improves the NH₃ adsorption property on the Fe₃O₄/AC surface. NO molecule can combine with Cr, Fe, and O sites to form nitrosyl and nitrite. The doping of Cr increases the adsorption performance of NO on the Fe₂O₃/AC and Fe₃O₄/AC surfaces, especially for Fe₃O₄/AC surface. Furthermore, NO can be oxidized to NO₂ by adsorption oxygen or active O sites of Fe_xO_y clusters. The doping of Cr restrains the formation of insoluble chelating bidentate nitrates and greatly reduces the reaction energy barrier of NO oxidation on the Fe_xO_y/AC surface, which can promote the deNO_x reaction.

Enhanced electro-Fenton catalytic performance with in-situ grown Ce/Fe@NPC-GF as self-standing cathode: Fabrication, influence factors and mechanism

Heterogeneous electro-Fenton (E-F) is considered as an attractive technique for efficient removal of refractory organic pollutants in wastewater. The regeneration of Fe^II and catalyst reusability are key issues for effective and sustainable degradation. Developing binder-free iron phase/carbon composite cathode is a feasible strategy. In this work, the stable Ce/Fe-nanoporous carbon modified graphite felt electrode (Ce/Fe@NPC-GF) was fabricated using in situ solvothermal method and subsequent carbonization treatment, which worked as the cathode in a heterogeneous electro-Fenton system to degrade sulfamethoxazole. The electrocatalytic activity was significantly improved with doping of Ce. It was found that mesoporous Ce/Fe@NPC-GF cathode demonstrated high oxygen reduction activity and low resistance. The co-existence of Fe^Ⅱ/Fe^Ⅲ and Ce^Ⅲ/Ce^Ⅳ redox couples enhanced remarkably interfacial electron transfer, promoting in-situ H₂O₂ generation and decomposition, sequentially boosting the production of reactive radicals (·OH and ·O₂^-). Under 20 mA and pH 3, Sulfamethoxazole (SMX) was basically degraded in 120 min, and the removal rate was satisfactory in wide pH (2-6). After 8 cycles, the electrode could still maintain high stability and outstanding catalytic capacity. This work displayed a novel in-situ preparation method of composite cathode with excellent catalytic performance in E-F system, which offered inspiration for developing efficient heterogeneous electro-Fenton cathode material.

Flame synthesized nanoscale catalyst (CuCeWTi) with excellent Hg0 oxidation activity and hydrothermal resistance

In view of poor hydrothermal resistance of impregnation prepared catalysts (Cu5Ce5W9Ti-I), this paper aims to enhance thermal and hydrothermal resistance of Cu/Ce based catalysts for Hg⁰ oxidation via flame synthesis technology. The result found that the flame synthesis method could form nanoscale Cu10Ce10W9Ti-F particles with smaller lattice size (8-25 nm), more stable carrier structure and more oxygen vacancies. The inter-doping and inter-substitution of Ce, Cu and Ti oxides created more oxygen vacancies (Ce³⁺) and L-sites (O^2-). Furthermore, the carrier TiO₂ of Cu10Ce10W9Ti-F existed in form of highly thermostable rutile rather than anatase. High Hg⁰ oxidation efficiency (MOE) of 83.9-99.7% at 100-450 °C proved excellent oxidation activity of Cu10Ce10W9Ti-F catalyst. Moreover, the thermal and hydrothermal treatment (700 °C) only decreased MOE by less than 5% since L-sites kept fine thermostability of Cu10Ce10W9Ti-F. The flame synthesis was proven to be a promising catalyst preparation method to enhance thermal and hydrothermal resistance.

Preparation and Performance of Cerium-Based Catalysts for Selective Catalytic Reduction of Nitrogen Oxides: A Critical Review

Selective catalytic reduction of nitrogen oxides with NH3 (NH3-SCR) is still the most commonly used control technology for nitrogen oxides emission. Specifically, the application of rare earth materials has become more and more extensive. CeO2 was widely developed in NH3-SCR reaction due to its good redox performance, proper surface acidity and abundant resource reserves. Therefore, a large number of papers in the literature have described the research of cerium-based catalysts. This review critically summarized the development of the different components of cerium-based catalysts, and characterized the preparation methods, the catalytic performance and reaction mechanisms of the cerium-based catalysts for NH3-SCR. The purpose of this review is to highlight: (1) the modification effect of the various metal elements for cerium-based catalysts; (2) various synthesis methods of the cerium-based catalysts; and (3) the physicochemical properties of the various catalysts and clarify their relations to catalytic performances, particularly in the presence of SO2 and H2O. Finally, we hope that this work can give timely technical guidance and valuable insights for the applications of NH3-SCR in the field of NOx control.

Novel porous ceramic sheet supported metal reactors for continuous-flow catalysis

A novel porous ceramic sheet supported nickel particles reactor was obtained by an in-situ preparation method. This reactor was then used to investigate continuous-flow catalysis of nitroaromatic compounds and methyl orange. The details of the structure and morphology were characterized by XRD, SEM, XPS, Raman, element mapping, mercury intrusion method and Archimedes principle. The porous ceramic sheet supported Ni particles reactor exhibited excellent catalytic performance in the catalytic reduction of p-nitrophenol and methyl orange by sodium borohydride at room temperature. Both the conversion of p-nitrophenol (5 mM) and methyl orange (0.3 mM) reached nearly 100% at the injection speed of 2.67 mL·min^-1. In addition, it maintained conversions of 100% after 10 recycling time since the porous ceramic sheet could reduce the aggregation for Ni particles. Furthermore, the chemisorbed oxygen, and the strong interaction between Ni and porous ceramic sheet resulted in a highly efficient, recoverable, and cost-effective multifunctional reactor. All of these advantages present new opportunities to be implemented in the field of waste water treatment and environmental toxicology. Ultimately, the porous ceramic sheet could also support other metal nanomaterial, and used in other fields of environmental catalysis.

A DFT-D study on the reaction mechanism of selective catalytic reduction of NO by NH3 over the Fe2O3/Ni(111) surface

The adsorption and SCR reaction mechanism of NH₃, NO, and O₂ molecules on the Fe₂O₃/Ni(111) catalyst surface was revealed.

Selective catalytic reduction of NO over W–Zr-Ox/TiO2: performance study of hierarchical pore structure

A series of W–Zr-Ox/TiO2 catalysts with hierarchical pore structure were prepared and used for selective catalytic reduction of NO by NH3.

Strong interaction between Au nanoparticles and porous polyurethane sponge enables efficient environmental catalysis with high reusability

A novel and recoverable platform of polyurethane (PU) sponge-supported Au nanoparticle catalyst was obtained by a water-based in-situ preparation process. The structure, chemical, and morphology properties of this platform were characterized by XRD, TGA, SEM, FT-IR, and XPS. The Au/PU sponge platform exhibited excellent catalytic performances in catalytic reductions of p-nitrophenol and o-nitroaniline at room temperature, and both catalytic reactions could be completed within 4.5 and 1.5 min, respectively. Furthermore, the strong interaction between Au nanoparticles and the PU sponge enabled the catalyst system to maintain a high catalytic efficiency after 5 recycling times, since the PU sponge reduced the trend of leaching and aggregation of Au nanoparticles. The unique nature of Au nanoparticles and the porous PU sponge along with their strong interaction resulted in a highly efficient, recoverable, and cost-effective multifunctional catalyst. The AuNP/Sponge nanocatalyst platform has great potential for wide environmental and other catalytic applications.

Resource utilization of waste V2O5-based deNOx catalysts for hydrogen production from formaldehyde and water via steam reforming

The harmless disposal of abandoned and toxic V₂O₅(WO₃)/TiO₂ (VWT) deNO_x catalysts has become a worldwide great demand, a new resource path for hydrogen production from steam reforming of formaldehyde and water using the waste VWT deNOx catalysts as catalyst carriers was proposed. The waste V₂O₅-based catalysts supported NiO (N/VWT) catalysts prepared by impregnation method were comparatively studied for hydrogen production. The H₂ and CO selectivity of the optimum N/VWT separately reached 100% and 72.5%, and the formaldehyde conversion of the N/VWT reached 86.3% at 400 ℃ and higher than 93.0% at 450-600 ℃. Analysis showed that the hydroxyl species played the most important role, and its richness determined the catalytic performance directly. The high acid sites and excellent redox properties were beneficial to enhance the catalytic performance. The in situ DRIFT study verified that the hydrogen bonds between formate species and hydroxyl groups reduced reaction steps, which accelerated the progress of the reaction. The adsorbed formaldehyde transformed to formate species firstly, and then produced H₂ and CO₂ (or CO) by dehydrogenation. Ultimately, the resource utilization path not only completely solved the harmless problems of the waste V₂O₅-based deNO_x catalysts and formaldehyde, but also contributed to the hydrogen production.

Promotion effect of cerium doping on iron–titanium composite oxide catalysts for selective catalytic reduction of NOx with NH3

Doping with a suitable amount of Ce enhances the SCR performance of FeTi catalysts.

Recent advances in microfluidic platforms for single-cell analysis in cancer biology, diagnosis and therapy

Understanding molecular, cellular, genetic and functional heterogeneity of tumors at the single-cell level has become a major challenge for cancer research. The microfluidic technique has emerged as an important tool that offers advantages in analyzing single-cells with the capability to integrate time-consuming and labour-intensive experimental procedures such as single-cell capture into a single microdevice at ease and in a high-throughput fashion. Single-cell manipulation and analysis can be implemented within a multi-functional microfluidic device for various applications in cancer research. Here, we present recent advances of microfluidic devices for single-cell analysis pertaining to cancer biology, diagnostics, and therapeutics. We first concisely introduce various microfluidic platforms used for single-cell analysis, followed with different microfluidic techniques for single-cell manipulation. Then, we highlight their various applications in cancer research, with an emphasis on cancer biology, diagnosis, and therapy. Current limitations and prospective trends of microfluidic single-cell analysis are discussed at the end.