Promotion of Pd nanoparticles by Fe and formation of a Pd3Fe intermetallic alloy for propane dehydrogenation

Anode-Free Aqueous Aluminum Ion Batteries

Aqueous aluminum ion batteries (AAIBs) possess the advantages of high safety, cost-effectiveness, eco-friendliness and high theoretical capacity. However, the Al2O3 film on the Al anode surface, a natural physical barrier to the plating of hydrated aluminum ions, is a key factor in the decomposition of the aqueous electrolyte and the severe hydrogen precipitation reaction. To circumvent the obnoxious Al anode, a proof-of-concept of an anode-free AAIB is first proposed, in which Al2TiO5, as a cathode pre-aluminum additive (Al source), can replenish Al loss by over cycling. The Al-Cu alloy layer, formed by plating Al on the Cu foil surface during the charge process, possesses a reversible electrochemical property and is paired with a polyaniline (cathode) to stimulate the battery to exhibit high initial discharge capacity (175 mAh g-1), high power density (≈410 Wh L-1) and ultra-long cycle life (4000 cycles) with the capacity retention of ≈60% after 1000 cycles. This work will act as a primer to ignite the enormous prospective researches on the anode-free aqueous Al ion batteries.

Mechanism research reveals the role of Fen (n = 2-5) supported C2N as single-cluster catalysts (SCCs) for the non-oxidative propane dehydrogenation in the optimization of catalytic performance

Single cluster catalysts show excellent potential for propane dehydrogenation, compensating for the limited catalytic performance of single-atom catalysts in reactions involving multiple reaction steps and intermediates. Herein, density functional theory is used to investigate the catalytic activity and mechanism for non-oxidized propane dehydrogenation on Fen-C2N (n = 2-5). Firstly, the stability of Fen-C2N (n = 2-5) is evaluated by comparing the mean values of binding energy and cohesive energy. The results show that Fen-C2N (n = 2-4) can exist stably, which is also verified by the molecular dynamics calculation at 873 K. Band structure analysis shows that the screened catalysts have metal properties, which are conducive to charge transfer. Fukui function analysis is used to predict the optimal adsorption site. The electronic properties of propane and propylene adsorbed on catalysts are further studied by the partial density of states and deformation charge density. The activation barrier (Ea) and reaction energy (ΔE) of the main reaction steps are evaluated. The results show that Fe2-C2N (Ea = 0.97 eV, ΔE= 0.22 eV) has the best catalytic activity. The Ea for further propylene dehydrogenation is also used to evaluate the yield of propylene. Compared with Fe-C2N, Fe2-C2N can regulate the adsorption strength of propane and propylene, showing better catalytic ability and higher selectivity for propylene. The above research provides ideas for the design of new catalysts with high selectivity and activity for non-oxidative propane dehydrogenation.

Solid-Solution-Based Metal Coating Enables Highly Reversible, Dendrite-Free Aluminum Anode

Aluminum-ion batteries have attracted great interest in the grid-scale energy storage field due to their good safety, low cost and the high abundance of Al. However, Al anodes suffer from severe dendrite growth, especially at high deposition rates. Here, we report a simple strategy for constructing a highly reversible, dendrite-free, Al-based anode through directly introducing a solid-solution-based metal coating to a Zn foil substrate. Compared with Cu foil substrates and bare Al, a Zn foil substrate shows a lower nucleation barrier of Al deposition due to the intrinsic, definite solubility between Al and Zn. During Al deposition, a thin, solid-solution alloy phase is first formed on the surface of the Zn foil substrate and then guides the parallel growth of flake-like Al on Zn substrate. The well-designed, Zn-coated Al (Zn@Al) anode can effectively inhibit dendrite growth and alleviate the corrosion of the Al anode. The fabricated Zn@Al–graphite battery exhibits a high specific capacity of 80 mAh·g−1 and an ultra-long lifespan over 10,000 cycles at a high current density of 20 A·g−1 in low-cost molten salt electrolyte. This work opens a new avenue for the development of stable Al anodes and can provide insights for other metal anode protection.

C-H bond activation in light alkanes: a theoretical perspective

Alkanes are the major constituents of natural gas and crude oil, the feedstocks for the chemical industry. The efficient and selective activation of C-H bonds can convert abundant and low-cost hydrocarbon feedstocks into value-added products. Due to the increasing global demand for light alkenes and their corresponding polymers as well as synthesis gas and hydrogen production, C-H bond activation of light alkanes has attracted widespread attention. A theoretical understanding of C-H bond activation in light hydrocarbons via density functional theory (DFT) and microkinetic modeling provides a feasible approach to gain insight into the process and guidelines for designing more efficient catalysts to promote light alkane transformation. This review describes the recent progress in computational catalysis that has addressed the C-H bond activation of light alkanes. We start with direct and oxidative C-H bond activation of methane, with emphasis placed on kinetic and mechanistic insights obtained from DFT assisted microkinetic analysis into steam and dry reforming, and the partial oxidation dependence on metal/oxide surfaces and nanoparticle size. Direct and oxidative activation of the C-H bond of ethane and propane on various metal and oxide surfaces are subsequently reviewed, including the elucidation of active sites, intriguing mechanisms, microkinetic modeling, and electronic features of the ethane and propane conversion processes with a focus on suppressing the side reaction and coke formation. The main target of this review is to give fundamental insight into C-H bond activation of light alkanes, which can provide useful guidance for the optimization of catalysts in future research.

Dehydrogenation of light alkanes to mono-olefins

In the past several decades, light alkane dehydrogenation to mono-olefins, especially propane dehydrogenation to propylene has gained widespread attention and much development in the field of research and commercial application. Under suitable conditions, the supported Pt-Sn and CrO_x catalysts widely used in industry exhibit satisfactory dehydrogenation activity and selectivity. However, the high cost of Pt and the potential environmental problems of CrO_x have driven researchers to improve the coking and sintering resistance of Pt catalysts, and to find new non-noble metal and environment-friendly catalysts. As for the development of the reactor, it should be noted that low operation pressure is beneficial for improving the single-pass conversion, decreasing the amount of unconverted alkane recycled back to the reactor, and reducing the energy consumption of the whole process. Therefore, the research direction of reactor improvement is towards reducing the pressure drop. This review is aimed at introducing the characteristics of the dehydrogenation reaction, the progress made in the development of catalysts and reactors, and a new understanding of reaction mechanism as well as its guiding role in the development of catalyst and reactor.

A Comprehensive Study of Coke Deposits on a Pt-Sn/SBA-16 Catalyst during the Dehydrogenation of Propane

Catalytic propane dehydrogenation is an attractive method to produce propylene while avoiding the issues of its traditional synthesis via naphtha steam cracking of naphtha. In this contribution, a series of Pt-Sn/SBA-16 catalysts were synthesized and evaluated for this purpose. Bimetallic Pt-Sn catalysts were more active than catalysts containing only Pt. The catalyst with the best performance was assessed at different reaction times of 0, 60, 180, and 300 min. The evolution of coke deposits was also studied. Thermogravimetric analysis demonstrated the presence of two types of coke on the catalyst surface at low and high temperature, respectively. Raman results showed an increased coke’s crystal size from 60 to 180 min on stream, and from 180 to 300 min under reaction, Raman suggested a reduction in the crystal size of coke. Also transmission electron microscopy confirmed a more evident agglomeration of metallic particles with reaction times higher than 180 min. These results are consistent with the phenomena called “coke migration” and the cause is often explained by coke movement near the particle to the support; it can also be explained due to sintering of the metallic particle, which we propose as a more suitable explanation.

Metal-based catalysts for the non-oxidative dehydrogenation of light alkanes to light olefins

This review provides an overview of metal-based catalysts, including Pt-, Pd-, Rh- and Ni-based bimetallic catalysts for non-oxidative dehydrogenation of light alkanes to olefins.

Recent progress in heterogeneous metal and metal oxide catalysts for direct dehydrogenation of ethane and propane

Metal and metal oxide catalysts for non-oxidative ethane/propane dehydrogenation are outlined with respect to catalyst synthesis, structure–property relationship and catalytic mechanism.

The impact of synthetic method on the catalytic application of intermetallic nanoparticles

Intermetallic alloy nanocrystals have emerged as a promising next generation of nanocatalyst, largely due to their promise of surface tunability. Atomic control of the geometric and electronic structure of the nanoparticle surface offers a precise command of the catalytic surface, with the potential for creating homogeneous active sites that extend over the entire nanoparticle. Realizing this promise, however, has been limited by synthetic difficulties, imparted by differences in parent metal crystal structure, reduction potential, and atomic size. Further, little attention has been paid to the impact of synthetic method on catalytic application. In this review, we seek to connect the two, organizing the current synthesis methods and catalytic scope of intermetallic nanoparticles and suggesting areas where more work is needed. Such analysis should help to guide future intermetallic nanoparticle development, with the ultimate goal of generating precisely controlled nanocatalysts tailored to catalysis.

Architecting a Stable High-Energy Aqueous Al-Ion Battery

Aqueous Al-ion batteries (AAIBs) are the subject of great interest due to the inherent safety and high theoretical capacity of aluminum. The high abundancy and easy accessibility of aluminum raw materials further make AAIBs appealing for grid-scale energy storage. However, the passivating oxide film formation and hydrogen side reactions at the aluminum anode as well as limited availability of the cathode lead to low discharge voltage and poor cycling stability. Here, we proposed a new AAIB system consisting of an Al_xMnO₂ cathode, a zinc substrate-supported Zn-Al alloy anode, and an Al(OTF)₃ aqueous electrolyte. Through the in situ electrochemical activation of MnO, the cathode was synthesized to incorporate a two-electron reaction, thus enabling its high theoretical capacity. The anode was realized by a simple deposition process of Al³⁺ onto Zn foil substrate. The featured alloy interface layer can effectively alleviate the passivation and suppress the dendrite growth, ensuring ultralong-term stable aluminum stripping/plating. The architected cell delivers a record-high discharge voltage plateau near 1.6 V and specific capacity of 460 mAh g^-1 for over 80 cycles. This work provides new opportunities for the development of high-performance and low-cost AAIBs for practical applications.

Direct Catalytic Conversion of Ethanol to C5+ Ketones: Role of Pd-Zn Alloy on Catalytic Activity and Stability

Ethanol can be used as a platform molecule for synthesizing valuable chemicals and fuel precursors. Direct synthesis of C₅₊ ketones, building blocks for lubricants and hydrocarbon fuels, from ethanol was achieved over a stable Pd-promoted ZnO-ZrO₂ catalyst. The sequence of reaction steps involved in the C₅₊ ketone formation from ethanol was determined. The key reaction steps were found to be the in situ generation of the acetone intermediate and the cross-aldol condensation between the reaction intermediates acetaldehyde and acetone. The formation of a Pd-Zn alloy in situ was identified to be the critical factor in maintaining high yield to the C₅₊ ketones and the stability of the catalyst. A yield of >70 % to C₅₊ ketones was achieved over a 0.1 % Pd-ZnO-ZrO₂ mixed oxide catalyst, and the catalyst was demonstrated to be stable beyond 2000 hours on stream without any catalyst deactivation.

Structural trends in the dehydrogenation selectivity of palladium alloys

Alloying is well-known to improve the dehydrogenation selectivity of pure metals, but there remains considerable debate about the structural and electronic features of alloy surfaces that give rise to this behavior. To provide molecular-level insights into these effects, a series of Pd intermetallic alloy catalysts with Zn, Ga, In, Fe and Mn promoter elements was synthesized, and the structures were determined using in situ X-ray absorption spectroscopy (XAS) and synchrotron X-ray diffraction (XRD). The alloys all showed propane dehydrogenation turnover rates 5–8 times higher than monometallic Pd and selectivity to propylene of over 90%. Moreover, among the synthesized alloys, Pd₃M alloy structures were less olefin selective than PdM alloys which were, in turn, almost 100% selective to propylene. This selectivity improvement was interpreted by changes in the DFT-calculated binding energies and activation energies for C–C and C–H bond activation, which are ultimately influenced by perturbation of the most stable adsorption site and changes to the d-band density of states. Furthermore, transition state analysis showed that the C–C bond breaking reactions require 4-fold ensemble sites, which are suggested to be required for non-selective, alkane hydrogenolysis reactions. These sites, which are not present on alloys with PdM structures, could be formed in the Pd₃M alloy through substitution of one M atom with Pd, and this effect is suggested to be partially responsible for their slightly lower selectivity.

Alloying is well-known to improve the dehydrogenation selectivity of pure metals, but there remains considerable debate about the structural and electronic features of alloy surfaces that give rise to this behavior.

The effect of strong metal–support interaction (SMSI) on Pt–Ti/SiO2 and Pt–Nb/SiO2 catalysts for propane dehydrogenation

The selectivity of Pt NP's (gray) are modified by SMSI oxides (red) leaving exposed small ensembles capable of dehydrogenation, but with limited activity for hydrogenolysis.

Two-dimensional transition metal carbides as supports for tuning the chemistry of catalytic nanoparticles

Supported nanoparticles are broadly employed in industrial catalytic processes, where the active sites can be tuned by metal-support interactions (MSIs). Although it is well accepted that supports can modify the chemistry of metal nanoparticles, systematic utilization of MSIs for achieving desired catalytic performance is still challenging. The developments of supports with appropriate chemical properties and identification of the resulting active sites are the main barriers. Here, we develop two-dimensional transition metal carbides (MXenes) supported platinum as efficient catalysts for light alkane dehydrogenations. Ordered Pt₃Ti and surface Pt₃Nb intermetallic compound nanoparticles are formed via reactive metal-support interactions on Pt/Ti₃C₂T_x and Pt/Nb₂CT_x catalysts, respectively. MXene supports modulate the nature of the active sites, making them highly selective toward C–H activation. Such exploitation of the MSIs makes MXenes promising platforms with versatile chemical reactivity and tunability for facile design of supported intermetallic nanoparticles over a wide range of compositions and structures.

The performance of supported metal nanoparticle catalysts can be tailored by metal-support interactions, but their use in catalyst design is still challenging. Here, the authors develop two-dimensional transition metal carbides as platforms for designing intermetallic compound catalysts that are efficient for light alkane dehydrogenations.