Efficient dye-sensitized solar cells based on concerted companion dyes: systematic optimization of thiophene units in the organic dye components

The influence of the position and quantity of thiophene or acetylene groups on the photoelectric properties of dye-sensitized solar cells

To investigate the influence of the position and quantity of thiophene or acetylene groups on the photoelectric properties of dye-sensitized solar cells (DSSCs), density functional theory (DFT) were employed to simulate five zinc porphyrin dye molecules (T-3, T-3-D, T-3-A, T-3-AD, and T-3-ace). The optimized geometry indicated that T-3-ace possessed superior planar properties, attributed to incorporating the acetylene groups, facilitating the charge transfer process. The lower lowest unoccupied molecular orbital (LUMO) energy levels of T-3-ace and T-3-D suggested that introducing thiophene or acetylene groups on the donor side enhanced the electron absorption capability of the dyes. The analysis of optical properties revealed that the incorporation of thiophene or acetylene groups on the donor side (T-3-D or T-3-ace) exhibited a more prominent red shift and a broader absorption range, which was beneficial for promoting electron excitation and optical properties. The low reorganization energy suggested these two molecules have better structural stability during photoexcitation. The prediction of photoelectric conversion efficiency (PCE) showed that introducing thiophene was beneficial for improving the PCE, with the most significant effect observed when introducing thiophene groups on the donor side (T-3-D). The T-3-ace demonstrated the highest maximum short circuit current density Jmax; however, the lower electron injection efficiency (φinject) led to a lower short circuit current density JSC and consequently a lower PCE. This work is conducive to providing valuable insights into the molecular structure of zinc porphyrin dyes and their photoelectric properties.

Kinetic and Theoretical Studies of 3,5-Dicyanothiophene Reactivity with Cyclic Secondary Amines in Water and Acetonitrile: Quantification, Correlation, and Prediction

The kinetics of the σ-complexation reactions of 3,5-dicyanothiophene 1 with a series of cyclic secondary amines 2a-c has been studied in water and acetonitrile at 20 °C. Through the linear free energy relationship (LFER) log k = sN (N + E), the electrophilicity parameter E of 3,5-dicyanothiophene 1 has been determined and then integrated into the electrophilicity scale established by Mayr. Molecular dynamics (MD) simulations have been employed to elucidate the reversal in reactivity order between piperidine and pyrrolidine observed in water. Reactivity descriptors like the electronic chemical potential (μ) and the chemical hardness (η) for a series of thiophenes were calculated using the density functional theory (DFT) method. Satisfactory linear correlation (r2 > 0.98) between the experimental electrophilicity parameter (E) of thiophenes 1 and 5a-c and their theoretical global electrophilicity index (ω) has been observed and discussed. In addition, we explore how the E vs. ω relationship can be used to evaluate the electrophilicity parameter E values for other thiophenes that cannot directly measure.

A Class of Heptaphyrins with NIR Absorption Modulated by Metal Coordination and Nucleophilic Substitution

The intensive interest in expanded porphyrins can be attributed to their appealing photoelectric and coordination behavior. In this work, an N-confused heptaphyrin 1 was synthesized by an acid-catalyzed [3+4] condensation reaction. The introduction of an N-confused pyrrolic unit into the heptaphyrin macrocycle led to the formation of a figure-eight-like conformation with nonsymmetrical "NNNN" and "NNNC" coordination cavities employable for bimetallic coordination. As a result, chelation of 1 with Zn(II) and Cu(II) afforded mono-Zn(II) complex 2 and bis-Cu(II) complex 3, respectively, with the metal atoms exhibiting distorted square-planar geometries. In complex 3, an oxygen atom is attached to the α-C atom of N-confused pyrrole D, and thus the N and C atoms of ring D participate in coordination within the two cavities. Interestingly, treatment of 1 with Cs2CO3 in MeOH resulted in regioselective substitution of all the seven para-F atoms in the meso-C6F5 groups as well as the α-H of ring D by eight methoxy moieties. Complex 3 displays a red-shifted absorption band edge of ca. 2200 nm, compared to that of ca. 1600 nm observed for 1. This work provides an example of incorporating an N-confused pyrrole to construct expanded porphyrins with distinctive coordination behavior and tunable NIR absorption.

Enhanced Efficiency of Dye-Sensitized Solar Cells by Controlled Co-Adsorption Self-Assembly of Dyes

Single dyes typically exhibit limited light absorption in dye-sensitized solar cells (DSSCs). Thus, cosensitization using two or more dyes to enhance light-harvesting efficiency has been explored; however, the aggregation of dyes can adversely affect electron injection capabilities. This study focused on the design and synthesis of three dyes with a common carbazole donor for DSSCs: DZ102, TZ101, and JM102. JM102 broadens the absorption spectrum by replacing the benzoic acid electron acceptor of TZ101 with acetylenic benzoic acid. A cosensitized DSSC device based on CO-1 [DZ102:TZ101 = 1:1 (50 μM:50 μM)] achieved a short-circuit current density of 19.4 mA/cm2 and a power conversion efficiency of 10.9%. For the first time, the molecular interactions between the dyes in the photoanode were demonstrated using cyclic voltammetry, which revealed the presence of intermolecular forces. Adsorption kinetics further indicated that these forces promoted the self-assembly of dyes during adsorption, which resulted in a cosensitization adsorption amount greater than the sum of the individual dye adsorptions. This study provides novel insights into the selection of cosensitizing dyes for DSSCs.

Structural Decoration of Porphyrin/Phthalocyanine Photovoltaic Materials

Porphyrin/phthalocyanine compounds with fascinating molecular structures have attracted widespread attention in the field of solar cells in recent years. In this review, we focus on the pivotal role of porphyrin and phthalocyanine compounds in enhancing the efficiency of solar cells. The review seamlessly integrates the intricate molecular structures of porphyrins and phthalocyanines with their proficiency in absorbing visible light and facilitating electron transfer, key processes in converting sunlight into electricity. By delving into the nuances of intramolecular regulation, aggregated states, and surface/interface structure manipulation, it elucidates how various levels of molecular modifications enhance solar cell efficiency through improved charge transfer, stability, and overall performance. This comprehensive exploration provides a detailed understanding of the complex relationship between molecular design and solar cell performance, discussing current advancements and potential future applications of these molecules in solar energy technology.

Pd(II) and Cu(III) Complexes of Multiply Fused Pentaphyrin Isomers with Tunable Structures and NIR Absorption

Fused porphyrinoids have received increasing interest in light of their extended conjugation and unique coordination behavior. On the basis of our previously reported multiply fused pentaphyrin isomers 1 and 2, a novel isomer 3 has been synthesized in this work. 3 possesses a hexacyclic fused moiety with a nearly coplanar CCNN cavity involving an inverted pyrrole, which is slightly different from the CNNN ones of 1 and 2 involving an N-confused pyrrole. 1-3 possess cavities with three depronatable protons and thus they all can generate Cu(III) complexes. However, only 3Cu is stable under ambient conditions. On the other hand, 3 remains intact upon treatment with Pd(II) ions, while 1 and 2 could undergo structural rearrangement to accommodate Pd(II), affording 1Pd and 2Pd accompanied by the formation of a lactone ring and the addition of a methoxy group, respectively. Compared with the free bases, the complexes show distinct aromaticity and more intense near-infrared (NIR) absorption up to ca. 1600, 1170, and 1500 nm, respectively. The results indicate that the subtle modification of the linking modes between the pyrrolic units in the fused pentaphyrinoids is effective in modulating the coordination behavior for synthesizing complexes with tunable aromaticity and NIR absorption.

Recent advances in the approaches for improving the photovoltaic performance of porphyrin-based DSSCs

Among other photovoltaic techniques including perovskite solar cells and organic solar cells, dye-sensitized solar cells (DSSCs) are considered to be a potential alternative to conventional silicon solar cells. Porphyrins are promising dyes with the properties of easy modification and superior light-harvesting capability. However, porphyrin dyes still suffer from a number of unfavorable aspects, which need to be addressed in order to improve the photovoltaic performance. This feature article briefly summarizes the recent progress in improving the Voc and Jsc of porphyrin-based DSSCs in terms of molecular engineering by modifying the porphyrin macrocycle, donor and acceptor moieties of the porphyrin dyes, coadsorption of the porphrin dyes with bulky coadsorbents like chenodeoxycholic acid (CDCA), and cosensitization of the porphyrin dyes with metal-free organic dyes. Notably, concerted companion (CC) dyes are described in detail, which have been constructed by linking a porphyrin dye subunit and a metal-free organic dye subunit with flexible alkoxy chains to achieve panchromatic absorption and concerted enhancement of Voc and Jsc. In one sentence, this article is expected to provide further insights into the development of high performance DSSCs through the design and syntheses of efficient porphyrin dyes and CC dyes in combination with device optimization to achieve simultaneously elevated Voc and Jsc, which may inspire and promote further progress in the commercialization of the DSSCs.

1,1'-Bis-(diphenylphosphino)ferrocene appended d8- and d10-configuration based thiosquarates: the molecular and electronic configurational insights into their sensitization and co-sensitization properties for dye sensitized solar cells

Three new d8- and d10-configuration based 1,1'-bis-(diphenylphosphino)ferrocene (dppf) appended thiosquarates complexes with general composition [M(mtsq)2dppf] (M = Ni2+ (NiL2); Zn2+ (ZnL2) and Cd2+ (CdL2)) (mtsq = 3-ethoxycyclobutenedione-4-thiolate) have been synthesized and characterized spectroscopically as well as in case of NiL2 by single crystal X-ray diffraction technique. The single crystal X-ray analysis reveals square planar geometry around Ni(II) in NiL2, where Ni(II) coordinates with two sulfur centres of two mtsq ligands in monodentate fashion and two phosphorus of a dppf ligand in chelating mode. The supramolecular architecture of NiL2 is sustained by intermolecular C-H⋯O interactions to form one-dimensional chain. Further, the application of these newly synthesized complexes as sensitizers and co-sensitizers/co-absorbents with ruthenium based N719 sensitizer in dye-sensitized solar cells (DSSCs) have been explored. The DSSC set-up based on NiL2 offers best photovoltaic performance with photovoltaic efficiency (η) 5.12%, short-circuit current (Jsc) 11.60 mA cm-2, open circuit potential (Voc) 0.690 V and incident photon to current conversion efficiency (IPCE) 63%. In co-sensitized DSSC set-up, ZnL2 along with state-of-the-art N719 dye displays best photovoltaic performance with η 6.65%, Jsc 14.47 mA cm-2, Voc 0.729 V and IPCE 69%, thereby showing an improvement by 15.25% in photovoltaic efficiency in comparison to the photovoltaic efficiency of N719 sensitized DSSC set-up. Variation in co-sensitization behaviour have been ascribed to the differences in the excited state energy level of co-sensitizers. The ZnL2 and CdL2 have a higher energy level position than N719 dye, allowing efficient electron transfer to N719 during light irradiation, while excited state of NiL2 is lower than N719 dye, preventing photoexcited electron transfer to N719, resulting in its lowest overall efficiency among the three co-sensitized DSSC setups.

Mono- and bis-Pd(ii) complexes of N-confused dithiahexaphyrin(1.1.1.1.1.0) with the absorption and aromaticity modulated by Pd(ii) coordination, macrocycle contraction and ancillary ligands

To further enrich the coordination chemistry of hexaphyrins and probe the underlying property-structural correlations, N-confused dithiahexaphyrin(1.1.1.1.1.0) (1) with 26 π-electron Hückel aromaticity was synthesized. Based on its unprecedented two unsymmetrical cavities, five palladium complexes 2, 3, 4-Ph, 4-Cl and 5 have been successfully synthesized under various coordinations. Thus, two mono-Pd(ii) complexes 2 and 3 with the Pd(ii) atom coordinated in the two different cavities were obtained by treating 1 with palladium reagents PdCl2, and (PPh3)2PdCl2 respectively. On this basis, bis-Pd(ii) complexes 4-Ph and 4-Cl were synthesized by treating 2 and 3 with (PPh3)2PdCl2 and PdCl2, respectively. As a result, both 4-Ph and 4-Cl contain two Pd(ii) atoms coordinated within the two cavities, with one of the Pd(ii) atoms further coordinated to a triphenylphosphine ligand in addition to an anionic ancillary ligand of Ph- and Cl-, respectively. Notably, a further contracted mono-Pd(ii) complex 5 was synthesized by treating 1 with Pd(PPh3)4 by eliminating one of the meso-carbon atoms together with the corresponding C6F5 moiety. These complexes present tunable 26 π aromaticity and NIR absorption up to 1060 nm. This work provides an effective approach for developing distinctive porphyrinoid Pd(ii) complexes from a single porphyrinoid, without resorting to tedious syntheses of a series of porphyrinoid ligands.

Visible-Light-Active Unsymmetrical Squaraine Dyes with Pyridyl Anchoring Groups for Dye-Sensitized Solar Cells

Visible-light-active alkyl group-wrapped unsymmetrical squaraine dyes SD1-SD3 were synthesized, featuring an indoline donor and pyridine and carboxylic acid anchoring groups. Their photophysical, electrochemical, and photovoltaic characteristics were examined by fabricating a dye-sensitized solar cell (DSSC) device. Both carboxylic acid and pyridine anchoring groups containing squaraine dyes SD3 and SD2 possess similar photophysical and electrochemical characteristics. However, their photovoltaic performances were completely different. The SD3 dye with the carboxylic acid anchoring group displayed a DSSC device efficiency of 7.20% (VOC 0.81 V; JSC 12.29 mA/cm2) using iodolyte (I-/I3-) electrolyte, compared to SD1 (VOC 0.659 V; JSC 4.97 mA/cm2; and η - 2.34%) and SD2 (VOC 0.629 V; JSC 1.68 mA/cm2; and η - 0.84%), which were featured with pyridyl anchoring groups. These results were attributed to dye loading on the Lewis and Brønsted acidic sites of TiO2 and the importance of aggregated structures for photocurrent generation. In the incident photon-to-current efficiency (IPCE) analysis, SD1 dye-sensitized devices exhibited photocurrent generation from both monomeric and aggregated dyes on the TiO2 surface. In contrast, SD2 showed photocurrent generation solely from aggregated states. Despite the introduction of long alkyl chains to reduce dye aggregation and charge recombination, the results indicated preferential charge injection from only the aggregated SD2 dye on TiO2. Fluorescence-quenching experiments indicated an efficient charge transfer from the aggregated SD2 dye to TiO2 compared to that of the monomeric dye. Cosensitization, a method to enhance the light-harvesting efficiency and photocurrent generation in DSSCs, was explored by simultaneously cosensitizing pyridyl-based dyes (SD1 and SD2) with a blue-colored carboxylic acid-based squaraine dye SD4. IPCE analysis demonstrated that both SD1 and SD4 contributed to generating a photocurrent of 9.11 mA/cm2. The sequential cosensitization of SD1 and SD4 with the coadsorbent CDCA showed the highest performance, with a VOC of 0.663 V, a JSC of 11.43 mA/cm2, and an efficiency (η) of 5.20%.

Syntheses of Thiophene-Thiophene-Linked Corrorin Dimers with Tunable Near-Infrared Absorption and Distinctive Reactivity

Thiahexaphyrinone 1 and thia-dipyrrin-appended corrorin 2 have been synthesized. Surprisingly, further oxidation of compound 2 with 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) in dichloromethane afforded dimer 3 with two molecules of compound 2 linked at the α-carbon atoms of the thienyl units. Treatment of compound 3 with DDQ in MeOH and SnCl2 in tetrahydrofuran/H2O afforded the dimethoxy-attached dimer 4 and hydrogenated dihydroxy-attached dimer 5, respectively. These results provide the first examples for synthesizing thiophene-linked porphyrinoid dimers with tunable near-infrared absorption and chirality.

Efficient Solar Cells Based on Porphyrin and Concerted Companion Dyes Featuring Benzo 12-Crown-4 for Suppressing Charge Recombination and Enhancing Dye Loading

In recent years, various porphyrin dyes have been designed to develop efficient dye-sensitized solar cells (DSSCs). Based on our previously reported porphyrin dye XW43, which contains a phenothiazine donor with two diethylene glycol (DEG)-derived substituents, we herein report a porphyrin dye XW89 by introducing a benzo 12-crown-4 (BCE) unit onto the N atom of the phenothiazine donor. On this basis, XW90 and XW91 have been synthesized by replacing a DEG chain in XW89 with two DEG chains and a 12-crown-4 unit, respectively. For iodine electrolyte-based DSSCs, dyes XW89-XW91 exhibit VOC values of 765-779 mV, higher than that of XW43 (755 mV), which may be related to the strong capability of the BCE group in binding Li+ and thus suppressing the downward shift of the TiO2 conduction band and interfacial charge recombination. Moreover, the smaller size of 12-crown-4 than the DEG unit enables higher adsorption amounts of the dyes than XW43, contributing to an enhanced JSC value. Due to the presence of two BCE units, dye XW91 exhibits the highest dye loading amount and JSC of 1.86 × 10-7 mol cm-2 and 19.79 mA cm-2, respectively, affording a high PCE of 11.1%. To further enhance the light-harvesting ability, a concerted companion (CC) dye XW92 has been constructed by linking the two subdye units corresponding to the porphyrin dye XW91 and an organic dye. As a result, XW92 affords an enhanced JSC and efficiency. Further coadsorption of XW92 with chenodeoxycholic acid achieved the highest efficiency of 12.1%. This work provides an effective approach for fabricating efficient DSSCs sensitized by porphyrin and CC dyes based on the introduction of crown ether units with smaller sizes and stronger Li+ affinities.

D-π-A Structured Porphyrin and Organic Dyes with Easily Synthesizable Donor Units for Low-Cost and Efficient Dye-Sensitized Solar Cells

This study aimed to develop low-cost D-π-A structured porphyrin and organic dyes with easily synthesizable donor units instead of the conventional complex multistep synthetic donor unit of Hexyloxy-BPFA [bis(7-(2,4-bis(hexyloxy)phenyl)-9,9-dimethyl-9H-fluoren-2-yl)amine] used in SGT-021 and SGT-149 as well-known record cosensitizers with an extremely high power conversion efficiency (PCE). The design strategy concerned the easier synthesis of low-cost donor units with inversion structures in donor groups via donor structural engineering, particularly by changing the position of the fluorene and phenylene units in the donor moiety while keeping the π-bridge and acceptor unit unchanged, leading to the synthesis of two D-π-A structured porphyrins [SGT-021(D0) and SGT-021(D)] and one D-π-A structured organic sensitizer [SGT-149(D)] for dye-sensitized solar cells (DSSCs). Specifically, porphyrin SGT-021(D0) incorporated two hexyl chains into the 9-position of each fluorene, while SGT-021(D) and SGT-149(D) substituted two hexyloxy chain units to the terminal position of each fluorene in the donor groups of porphyrin dyes. The effect of the position of the fluorene and phenylene units in the donor moiety on the photochemical and electrochemical properties, as well as the photovoltaic performance, was compared with the reference dyes of SGT-021 and SGT-149, previously reported by the research group. After optimizing the DSSC devices, SGT-021(D) and SGT-021(D0) achieved a high PCE of 11.6 and 10.5%, respectively, while SGT-149(D) exhibited a little lower PCE of 10.3% under the standard AM 1.5G light intensity. The cell performance of DSSC devices based on SGT-021(D) and SGT-149(D) was inferior to the corresponding reference dyes of SGT-021 and SGT-149 due to their lower donating ability of Hexyloxy-BPFA than Hexyloxy-BFPA.

Fused Double Donor Design with a Cross-Conjugated Dibenzosilin for Dye-Sensitized Solar Cells

Dye-sensitized solar cells (DSCs) can provide a clean energy solution to growing energy demands. In order to have devices of high performance, sensitizers that are able to absorb in the near-infrared region (NIR) are needed. Stronger electron donors are needed for intramolecular charge-transfer sensitizers to access longer wavelength photons. Thus, two novel organic dyes with a cross-conjugated dibenzosilin double donor design are studied herein. The double donor delocalizes multiple filled orbitals across both amine donors due to the fused design that planarizes the donor as observed computationally, which improves intramolecular charge-transfer strength. The dyes are studied via density functional theory (DFT), optical spectroscopy, electrochemistry, and in DSC devices. The studies indicate that the dye design can reduce recombination losses, allowing for improved DSC device performances relative to a single arylamine donor. The reduction in recombination losses is attributed to the six alkyl chains that are incorporated into the donor, which offer good surface protection.

Sensitizers of Metal Complexes with Sulfur Coordination Achieving a Power Conversion Efficiency of 12.89

In the study to improve the light absorption range and intensity of dye sensitizers in the visible region and promote their photovoltaic performance, five novel polymeric metal complexes with sulfur coordination (BDTT-VBT-Ni, BDTT-VBT-Cu, BDTT-VBT-Zn, BDTT-VBT-Cd, and BDTT-VBT-Hg) to be used as D-A-π-A motif dye sensitizers were designed, synthesized, and characterized. In these polymeric metal complexes with sulfur coordination, the metal complexes with sulfur coordination of benzodithiophene derivatives are used as auxiliary electron acceptors, 8-quinolinol derivatives are used as π-bridge and electron acceptors, and thienylbenzene-[1,2-b:4,5-b'] dithiophene (BDTT) are used as electron donors. The effect of different metal complexes with sulfur coordination on the photovoltaic performance of dye sensitizers has been systematically studied. Under AM 1.5 irradiation (100 mW cm^-2), the devices of dye-sensitized solar cells (DSSCs) based on five polymeric metal complexes with sulfur coordination exhibited a short-circuit current density (J_sc) of 13.43, 15.07, 18.00, 18.99, and 20.78 mA cm^-2, respectively, and their power conversion efficiencies (PCEs) were 7.10, 8.59, 10.68, 11.23, and 12.89%, respectively, and their thermal decomposition temperatures (T_d) were 251, 257, 265, 276, and 277 °C, respectively. The result shows that the J_sc and PCE of five polymeric metal complexes increase by degrees, and the PCE of BDTT-VBT-Hg is up to 12.89%, which is because of the strength of the coordination bonds between Ni(II), Cu(II), Zn(II), Cd(II), and Hg(II) and sulfur increases in turn so that the electron-withdrawing ability and electron-transfer ability of auxiliary electron acceptors is enhanced. These results provide a new way to develop stable and efficient metal complexes with sulfur coordination dye sensitizers in the future.

Solvent-Dependent Functional Aggregates of Unsymmetrical Squaraine Dyes on TiO2 Surface for Dye-Sensitized Solar Cells

Alkyl group wrapped donor-acceptor-donor (D-A-D) based unsymmetrical squaraine dyes SQ1, SQ5, and SQS4 were used to evaluate the effect of sensitizing solvents on dye-sensitized solar cell (DSSC) efficiency. A drastic change in DSSC efficiency was observed when the photo-anodes were sensitized in acetonitrile (bad solvent when considering dye solubility) and chloroform (good solvent) with an Iodolyte (I^-/I₃^-) electrolyte. The DSSC device sensitized with squaraine dyes in acetonitrile showed better photovoltaic performance with enhanced photocurrent generation and photovoltage compared to the device sensitized in chloroform. In a good sensitizing solvent, dyes with long hydrophobic alkyl chains are deleterious forming aggregates on the TiO₂ surface, which results in an incident photon-to-current conversion efficiency (IPCE) response mostly from monomeric and dimeric structures. Meanwhile, a bad sensitizing solvent facilitates the formation of well-packed self-assembled structures on the TiO₂ surface, which are responsible for a broad IPCE response and high device efficiencies. The photoanode sensitized in the bad sensitizing solvent showed enhanced V_OC values of 642, 675, and 699 mV; J_SC values of 6.38, 11.1, and 11.69 mA/cm²; and DSSC device efficiencies of 3.0, 5.63, and 6.13% for the SQ1, SQ5, and SQS4 dyes in the absence of a coadsorbent (chenodeoxycholic acid (CDCA)), respectively, which were further enhanced by CDCA addition. Meanwhile, the photoanode sensitized in the good sensitizing solvent showed relatively low photovoltaic V_OC values of 640, 652, and 650 mV; J_SC values of 5.78, 6.79, and 6.24 mA/cm²; and device efficiencies of 2.73, 3.35, and 3.20% for SQ1, SQ5, and SQS4 in the absence of CDCA, respectively, which were further varied with equivalents of CDCA. The best DSSC device efficiencies of 6.13 and 3.20% were obtained for SQS4 without CDCA, where the dye was sensitized in acetonitrile (bad) and chloroform (good) sensitizing solvents, respectively.

Influence of the π-Bridge-Fused Ring and Acceptor Unit Extension in D-π-A-Structured Organic Dyes for Highly Efficient Dye-Sensitized Solar Cells

Three new D-π-A-structured organic dyes, coded as SGT-138, SGT-150, and SGT-151, with the expansion of π-conjugation in the π-bridge and acceptor parts have been developed to adjust HOMO/LUMO levels and to expand the light absorption range of organic dyes. Referring to the SGT-137 dye, the π-bridge group was extended from the 4-hexyl-4H-thieno[3,2-b]indole (TI) to the 9-hexyl-9H-thieno[2',3':4,5]thieno[3,2-b]indole (TII), and the acceptor group was extended from (E)-3-(4-(benzo[c][1,2,5]thiadiazol-4-yl)phenyl)-2-cyanoacrylic acid (BTCA) to (E)-3-(4-(benzo[c][1,2,5]thiadiazol-4-ylethynyl)phenyl)-2-cyanoacrylic acid (BTECA), where TII was introduced as a π-bridging unit for the first time. It was determined that both extensions are promising strategies to enhance the light-harvesting ability. They present several features, such as (i) efficiently intensifying the extinction coefficient and expanding the absorption bands; (ii) exhibiting enhanced intramolecular charge transfer in comparison with the SGT-137; and (iii) being favorable to photoelectric current generation of dye-sensitized solar cells (DSSCs) with cobalt electrolytes. In particular, the π-spacer extension from TI to TII was useful for modulating the HOMO energy levels, while the acceptor extension from BTCA to BTECA was useful for modulating the LUMO energy levels. These phenomena could be explained with the aid of density functional theory calculations. Finally, the DSSCs based on new SGT-dyes with an HC-A1 co-adsorbent presented good power conversion efficiencies as high as 11.23, 11.30, 11.05, and 10.80% for SGT-137, SGT-138, SGT-150, and SGT-151, respectively. Furthermore, it was determined that the use of the bulky co-adsorbent, HC-A1, can effectively suppress the structural relaxation of dyes in the excited state, thereby enhancing the charge injection rate of SGT-dyes. The observations in time-resolved photoluminescence were indeed consistent with the variation in the PCE, quantitatively.

Aromatic-Ring-Fused BOPPY Fluorophores: Synthesis, Spectral, Redox Properties, and Bioimaging Application

Tetracoordinated organoboron dyes exhibiting strong fluorescence in either solution or the solid state are currently receiving much attraction in view of their photovoltaic, optoelectronic, and biological applications. Herein, a series of aromatic-ring-fused BOPPY dyes have been developed by one-pot condensation of formylated isoindoles or indoles and pyridinylhydrazine followed by subsequent borylation coordination. The facile synthesis provides excellent diversity of these unsymmetrical α-benzo- and β-benzothiophene-fused BOPPY dyes with intriguing photophysical properties owing to their rigid and planar structure and extended π-conjugation while containing a reactive site. They display intense green to orange fluorescence in solution and red-to-near-infrared emission in the solid state, with high fluorescence quantum yields up to 92 and 21%, respectively, relatively large Stokes shifts, and excellent photostability. Furthermore, two representative benzo-fused BOPPY probes with morpholine or benzenesulfonamide groups were developed and used to selectively "light up" the subcellular organelles such as lysosomes and endoplasmic reticulum under ultralow concentration, respectively.

Efficient Solar Cells Sensitized by Organic Concerted Companion Dyes Suitable for Indoor Lamps

In this work, organic concerted companion (CC) dyes CCOD-1 and CCOD-2 were constructed by covalently linking two organic dye units with complementary absorption spectra. Both CC dyes exhibited intense absorption from 300 to 650 nm with the band edges extended to 700 nm. These CC dyes were used to fabricate dye-sensitized solar cells (DSSCs), and the photovoltaic performance was investigated using different light sources. CCOD-2 possessed bulkier outer shelter than CCOD-1 owing to the longer carbon chains (C₁₂ ) at the donor moiety, and thus it had stronger anti-aggregation and anti-charge-recombination ability. Under simulated sunlight (AM1.5G), CCOD-2 exhibited enhanced photovoltaic behavior with an open-circuit voltage (V_OC ) of 759 mV, short-circuit current density (J_SC ) of 19.23 mA ⋅ cm^-2 , and power conversion efficiency (PCE) of 10.4 %, respectively. Notably, under the illumination of the indoor T5 fluorescent lamp (2500 lux), CCOD-2 afforded an enhanced PCE of 28.0 % with remarkable V_OC and J_SC of 692 mV and 0.424 mA cm^-2 , respectively. Notably, the PCE achieved for CCOD-2 outperformed those of the reference sensitizer N719 and our previously reported CC dyes XW61 and XW70-C8 under the same indoor lamp conditions. In summary, the novel organic CC dyes developed in this work were demonstrated to be promising for fabricating DSSCs to efficiently harvest the energy of indoor lamps.

Efficient Dye-Sensitized Solar Cells Based on a New Class of Doubly Concerted Companion Dyes

To develop efficient dye-sensitized solar cells (DSSCs), concerted companion (CC) dyes XW60-XW63 constructed from the covalent linkage of a strapped porphyrin dye unit and an organic dye unit have been reported to exhibit panchromatic absorption and excellent photovoltaic performance. However, these CC dyes only afforded moderate VOC values of ca. 763 mV, demonstrating relatively weak antiaggregation ability, which remains an obstacle for further enhancing the photovoltaic behavior. To address this problem, we herein develop porphyrin dyes XW77-XW80 with the macrocycles wrapped with alkoxy chains of various lengths (OC6H13-OC22H45) and the corresponding CC dyes XW81-XW84 containing these porphyrin dye units. Interestingly, the new CC dyes XW81-XW83 exhibit increasing VOC from 745 to 784 mV with the chain lengths extended from C6 to C18, and a lowered VOC of 762 mV was obtained for XW84 when the chain length was further extended to C22. As a result, XW83 afforded the highest PCE of 12.2%, which is, to the best of our knowledge, the record efficiency for the iodine electrolyte-based solar cells sensitized with a single dye. These results can be rationalized by the so-called doubly concerted companion (DCC) effects, that is, the two subdye units exhibit not only complementary absorption but also concerted antiaggregation with the long wrapping chains on the porphyrins unit simultaneously protecting the porphyrin macrocycle and the neighboring organic subdye unit, thus affording panchromatic absorption and strong antiaggregation and anticharge-recombination ability. These results provide a new approach for constructing a class of DCC dyes to achieve high-performance DSSCs without using any antiaggregating coadsorbent or absorption-enhancing cosensitizer.

Polyimide-Based Covalent Organic Framework as a Photocurrent Enhancer for Efficient Dye-Sensitized Solar Cells

Covalent organic frameworks (COFs) are of great interest in the energy and optoelectronic fields due to their high porosity, superior thermal stability, and highly ordered conjugated architecture, which are beneficial for charge migration, charge separation, and light harvesting. In this study, polyimide COFs (PI-COFs) are synthesized through the condensation reaction of pyromellitic dianhydride (PMDA) with tris(4-aminophenyl) amine (TAPA) and then doped in the TiO₂ photoelectrode of a dye-sensitized solar cell (DSSC) to co-work with N719 dye to explore their functionality. As a benchmark, the pristine DSSC without the doping of PI-COFs exhibits a power conversion efficiency of 9.05% under simulated one sun illumination. The doping of 0.04 wt % PI-COFs contributes an enhanced short-circuit current density (J_SC) from 17.43 to 19.03 mA/cm², and therefore, the cell efficiency is enhanced to 9.93%. The enhancement of J_SC is attributed to the bifunctionality of PI-COFs, which enhances the charge transfer/injection and suppresses the charge recombination through the host (PI-COF)-guest (N719 dye) interaction. In addition, the PI-COFs also function as a cosensitizer and contribute a small quantity of photoinduced electrons upon sunlight illumination. Surface modification of oxygen plasma improves the hydrophilicity of PI-COF particles and reinforces the heterogeneous linkage between PI-COF and TiO₂ nanoparticles, giving rise to more efficient charge injection. As a result, the champion cell exhibits a high power conversion efficiency of 10.46% with an enhanced J_SC of 19.43 mA/cm². This methodology of increasing solar efficiency by modification of the photoelectrode with the doping of PI-COFs in the TiO₂ nanoparticles is promising in the development of DSSCs.