Statistical optimization of Remazol Brilliant Blue R dye adsorption onto activated carbon prepared from pomegranate fruit peel

Carbon Dioxide Adsorption over Activated Biocarbons Derived from Lemon Peel

The rising concentration of CO2 in the atmosphere is approaching critical levels, posing a significant threat to life on Earth. Porous carbons derived from biobased materials, particularly waste byproducts, offer a viable solution for selective CO2 adsorption from large-scale industrial sources, potentially mitigating atmospheric CO2 emissions. In this study, we developed highly porous carbons from lemon peel waste through a two-step process, consisting of temperature pretreatment (500 °C) followed by chemical activation by KOH at 850 °C. The largest specific surface area (2821 m2/g), total pore volume (1.39 cm3/g), and micropore volume (0.70 cm3/g) were obtained at the highest KOH-to-carbon ratio of 4. In contrast, the sample activated with a KOH-to-carbon ratio of 2 demonstrated the greatest micropore distribution. This activated biocarbon exhibited superior CO2 adsorption capacity, reaching 5.69 mmol/g at 0 °C and 100 kPa. The remarkable adsorption performance can be attributed to the significant volume of micropores with diameters smaller than 0.859 nm. The Radke-Prausnitz equation, traditionally employed to model the adsorption equilibrium of organic compounds from liquid solutions, has been shown to be equally applicable for describing the gas-solid adsorption equilibrium. Furthermore, equations describing the temperature dependence of the Radke-Prausnitz equation's parameters have been developed.

Sustainable use of low-cost adsorbents prepared from waste fruit peels for the removal of selected reactive and basic dyes found in wastewaters

Agricultural wastes are potential sustainable adsorbents since they are available in large quantities, are low-cost, and may require little or no treatment, in some cases. In this study, several fruit peels, such as banana, orange, and pomegranate, were collected from local markets and prepared by a simple and eco-friendly method and used as natural adsorbents for the removal of both anionic (Reactive Red 120 (RR120), Reactive Black 5 (RB5), Remazol Brilliant Blue R (RBBR)) and cationic Methylene Blue (MB) dyes found in wastewaters. Many industries, such as leather and textiles, can release huge amounts of synthetic dyes into the wastewater during dyeing processes. These are one of the most important pollutants of water pollution as they cause enormous damage to the water body and also affect the health of organisms due to their toxicity and carcinogenicity. The search for a sustainable and at the same time efficient material for the removal of a wide variety of dyes is the innovation of this work. These peels were prepared by washing, drying, grinding, and finally sieving, under natural sustainable conditions. Porosometry (BET analysis), FTIR, SEM/EDS, and XRD techniques were used to characterize the fruit peels before and after the adsorption process. Factors affecting the adsorption of dyes (adsorbent dosage, pH solution, initial concentration of dyes, contact time, and temperature) were investigated. According to the results, in terms of the effectiveness of fruit peels as (natural) adsorbent materials, for anionic dyes, 5.0-6.0 g/L of banana or orange dry peels was sufficient to remove near or even more than 90% anionic dyes at pH 2.0, and 4.0 g/L was sufficient to remove 98% of cationic MB dye at pH 9.0. Similar amount of pomegranate peels had lower efficiency for anionic dyes (50-70%), while cationic MB was still efficiently removed (98%) at pH 9.0. Moreover, the adsorption process in all cases was found to better fit to pseudo-second-order model, in comparison to pseudo-first-order model. According to isotherms, Freundlich model fitted better in some cases to the equilibrium data, while the Langmuir model in others. Finally, this study demonstrates the viability of reusing the banana, orange, and pomegranate peel adsorbents for eight, four, and five cycles, showing a gradual reduction of around 50% of their effectiveness.

Production of MgFe2O4/activated carbons derived from a harmful grass Cynodon dactylon and their utilization for ciprofloxacin removal

Cynodon dactylon, an invasive species, exhibits its robust adaptability, reproduction and nutrient regime against the local species. Taking advantage of this harmful grass as a raw precursor to produce valuable materials for wastewater treatment has paid much attention. Herein, we report on the fabrication of Cynodom dactylon derived MgFe2O4@AC with a main goal of effective removal of ciprofloxacin antibiotic from water. Our findings showed that MgFe2O4@ACK1 composites attained mesoporous textures, high specific surface areas (884.3-991.6 m2 g-1), and MgFe2O4-20%@ACK1 was the most effective with a very high removal efficiency of 96.7%. The Elovich model was suitable for describing the kinetic of adsorption with (Radj)2 of 0.9988. Meanwhile, the isotherm data obeyed the Langmuir model corresponding to (Radj)2 of 0.9993. Qmax value of MgFe2O4-20%@ACK1 was determined at 211.67 mg g-1. The proposed adsorption mechanism primarily comprises five routes as follows, (i) pore-filling, (ii) π-π interaction, (iii) electrostatic interaction, (iv) hydrogen bonding, and (v) hydrophobic interaction. MgFe2O4-20%@ACK1 adsorbent could reuse with three cycles. We recommend that MgFe2O4/ACs derived from Cynodom dactylon could be high-efficiency adsorbents for the elimination of antibiotics.

Application of carbon from pomegranate husk for the removal of ibuprofen, cadmium and methylene blue from water

The presence of pharmaceutical products, dyes, and toxic metal ions in water is a major problem worldwide. This work developed low-cost pomegranate-based materials to uptake ibuprofen, cadmium and methylene blue from water. Pomegranate husks (PPH) were carbonized at 400 °C to form carbonized pomegranate husk (CPH), and nanoparticles were loaded into the carbon surface (NPH) by co-precipitation. SEM micrographs showed that the morphology of carbon was highly porous compared to pristine pomegranate husk. The data for BET revealed that CPH and NPH, had about a 20-fold increase in surface area of 142 m2/g and 190 m2/g respectively compared with 9.27 m2/g for PPH. The composites exhibited larger pore sizes and volumes. TEM images confirmed the loading of nanoparticles. The FTIR results showed that the materials had on their surface oxygenated groups such as -OH, -C]O, -COC and other groups like -NH and -C]C which are anticipated to play an essential role in the sorption of the pollutants. It was found that removal efficiency increased when there was a progressive increase in pollutant concentration for all adsorbents. The best pH value of the solution for the sorption processes was pH 8. The recorded adsorption capacities at pH 8 for Cd(II), IBU and MB were 92.85, 39.77 and 95.89 mg/g for NPH, 72.60, 32.58 and 80.59 mg/g for CPH and 32.78, 16.12 and 40.79 mg/g for PPH. Contact time studies showed three sorption steps. Step 1: rapid increase at the initial stage. Step 2: marginal uptake. Step 3: plateau. The trends indicated that sorption was influenced by temperature variation. The data for the thermodynamic parameter △Ho suggest that all the sorption processes were endothermic; the obtained positive values indicate this. The △Ho for PPH was between (64.33-69.08 kJ/mol), 82.84-86.03 kJ/mol for CPH and 87.17-88.96 kJ/mol for NPH. For PPH, molecular interactions were physisorption, and chemisorption for CPH and NPH. The △So has positive values, showing increased freedom during the sorption. The adsorbents followed PSO based on uptake processes involving syngenetic mechanisms.

The application of Rumex abyssinicus based activated carbon for Brilliant Blue Reactive dye adsorption from aqueous solution

The environmental pollution and human health impacts associated with the discharge of massive dye-containing effluents necessitate a search for cost-effective treatment technology. Therefore, this research work is conducted with the objective of investigating the potential of Rumex abyssinicus-derived activated carbon (RAAC) for the adsorption of Brilliant Blue Reactive (BBR) dye from aqueous solutions. Chemical activation with H₃PO₄ followed by pyrolysis was used to prepare the adsorbent. Characterization of the developed adsorbent was done using proximate analysis, pH point of zero charge (pHpzc), scanning electron microscope (SEM), Fourier transform infrared spectrometer (FTIR), Brunauer, Emmett, and Teller (BET), and X-ray diffraction (XRD). The experimental design and the effect of independent variables including pH (2, 6, and 10), initial dye concentration (50, 100, and 150 mg/L), adsorbent dosage (0.05, 0.1, and 0.15 g/100 mL), and contact time (20, 50, and 80 min) were optimized using the response surface methodology (RSM) coupled with Box Behnken design (BBD). The analysis results revealed the exitance of high specific surface area of 524 m²/g, morphological cracks, and the presence of multiple functional groups like -OH, C=C, alkene, and amorphous structure. Maximum removal efficiency of 99.98% was attained at optimum working conditions of pH 2, contact time of 50 min, dye concentration of 100 mg/L, and adsorbent dosage of 0.15 mg/100 mL, reducing the pollutant concentration from 100 to 0.02 mg/L. Evaluation of the experimental data was done using Langmuir, Freundlich, Temkin, and Sips isotherm models, in which the Langmuir model was found to be the best fit with the experimental data at R² 0.986. This shows that the adsorbent surface is homogeneous and mono-layered. Furthermore, the kinetic study confirmed that the pseudo second-order model best describes the experimental data with R² = 0.999. In general, the research work showed that the low cost, environmental friendliness and high adsorption capabilities of the activated carbon derived from Rumex abyssinicus could be taken as an effective nt for the removal of BBR dye from aqueous solutions.

Removal of anthraquinone dye from wastewaters by hybrid modified activated carbons

Dyes are among the main environmental pollutants, due to the high amount of discharge of wastewater, lost in the dyeing process, without any further treatment. Anthraquinone dyes are stable and resistant in the aquatic system. Among the methods that have been applied to remove these dyes from wastewaters, adsorption on activated carbon has been reported as a very effective technique, and its modification with oxides and hydroxides of metals have been used to increase its surface area. In the present study, the production of activated carbon was originated by coconut shells, and a mixture of metals and metalloids, such as magnesium, silicate, lanthanum, and aluminum (AC-Mg-Si-La-Al), was used for its subsequent modification and applied to Remazol Brilliant Blue R (RBBR) removal. AC-Mg-Si-La-Al surface morphology was studied by BET, FTIR, and SEM methods. For the evaluation of AC-Mg-Si-La-Al, several parameters, such as dosage, pH, contact time, and initial RBBR concentration were studied. According to the results, in pH 5.0 ± 0.1, the dye percentage rate reached 100% by applying 0.5 g/L. Therefore, the optimal dose of 0.4 g/L and pH 5.0 ± 0.1 are selected, which leads to 99% removal of RBBR. The experimental data found to better fit to Freundlich isotherm (R² = 0.9189) and pseudo-second-order kinetic (R² = 0.9291) models and 4 h were the sufficient time for adsorption. According to thermodynamics, a positive value of ∆H⁰ (19.661 kJ/mol) suggests the endothermic nature of the process. The AC-Mg-Si-La-Al adsorbent was able to regenerate after 5 cycles of use, showing only a 17% decrease in its efficiency. Because of its effectiveness in full RBBR removal, AC-Mg-Si-La-Al could be further examined for the removal of several other dyes, even anionic or cationic.

Statistical physics double-layer models for the experimental study and theoretical modeling of methyl orange dye adsorption on AlMnTiO nanocomposite

A Al₂O₃/MnO₂/TiO₂ (AlMnTiO) nanocomposite was synthesized using the thermal coprecipitation method and the adsorption performance of methyl orange (MO) dye from aqueous solution was carried out. Single-parameter optimization was used to explore the properties of AlMnTiO nanocomposite parameters on dye adsorption, including dose of adsorbent, solution pH, contact duration, and starting MO concentration. The model is the appropriate adsorption isotherm for the equilibrium process using a pseudo-second-order kinetic model property. Langmuir plot had a Q_max (mg/g) of 198.4 and best fitted (R²=0.990) among different isotherm models. The relevant parameters were computed using the dual-energy binary-layer statistical physics model. The statistical physics binary-layer model yield n (stoichiometric coefficient) values of 0.410, 0.440, and 0.453, all values are below 1, demonstrating the multi-docking process. AlMnTiO nanocomposite was regenerated up to six times, making the material extremely cost-effective. Using AlMnTiO nanocomposite, MO dye was removed from wastewater both in the laboratory and on the industrial scale.

A review on the treatment of dyes in printing and dyeing wastewater by plant biomass carbon

Printing and dyeing wastewater (PDW) has characteristics of large amount of water, elevated content of residual dyes, poor biodegradability, high alkalinity and large change of water quality, making its treatment difficult. Development of efficient and economic PDW treatment technology has gained considerable interest in the field of environmental protection. Use of plant biomass carbon (PBC) for the adsorption of dyes is a feasible and economical technology. This review summarizes current literature discussing the preparation method and physicochemical characteristics of PBC prepared from different plant species, the effect of PBC on the removal of dyes, influencing factors affecting the removal, and relevant adsorption models. The shortcomings of current research and the direction of future research are also pointed out in the review.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

A reusable mesoporous adsorbent for efficient treatment of hazardous triphenylmethane dye wastewater: RSM-CCD optimization and rapid microwave-assisted regeneration

In this research, mesoporous calcium aluminate nanostructures (meso-CaAl2O4) were synthesized using a citric acid-assisted sol-gel auto-combustion process as the potential adsorbent to eliminate toxic triphenylmethane dye malachite green (MG) from synthetic/real effluent. The surface morphology of meso-CaAl2O4 was highly porous with nanometric size and non-homogeneous surface. The specific surface area, total pore volume, and BJH pore diameter of meso-CaAl2O4 were 148.5 m2 g-1, 1.39 cm3 g-1, and 19 nm, respectively. The meso-CaAl2O4 also showed a very high heat resistance, due to losing only 7.95% of its weight up to 800 °C, which is mainly related to the moisture loss. The optimal adsorption conditions were obtained based on response surface methods (RSM)-central composite design (CCD) techniques. The Langmuir isotherm model was used for fitting the adsorption measurements, which presented 587.5 mg g-1 as the maximum adsorption capacity of the dye. The data obtained from the adsorption kinetics model were found to correspond to the pseudo-second-order model. Also, the thermodynamic parameters including enthalpy change (ΔH°), entropy change (ΔS°), and Gibbs free energy change (ΔG°) indicated that MG dye adsorption by the meso-CaAl2O4 was feasible, endothermic, and occurred spontaneously. Furthermore, the meso-CaAl2O4 was regenerated by microwave irradiation under 900 W at 6 min, and the MG dye removal efficiency was remained over 90% after the five cycles of microwave regeneration.

Remazol Brilliant Blue R (RBBR) dye and phosphate adsorption by calcium alginate beads modified with polyethyleneimine

This study concerns the preparation of novel adsorbent prepared from calcium alginate bead modified with polyethyleneimine (PEI-CaAlg). The adsorption capacity of the PEI-CaAlg was examined by Remazol Brilliant Blue R (RBBR) and phosphate adsorption. PEI-CaAlg showed high removal efficiencies for RBBR (90.48%) and phosphate (88.10%). The removal of both RBBR and phosphate onto the PEI-CaAlg followed the Freundlich isotherm and the second-order model. The adsorption was studied in terms of thermodynamic and found to be feasible and spontaneous in nature. The reusability of the modified alginate beads was also examined up to five cycles. The removal efficiency was 90.48% at the first cycle and decreased to 75.15% at the end of the fourth cycle. The adsorption of color and phosphate from real textile wastewater was also instigated. The removal efficiencies for color and phosphate ions reached 80.24% and 90.00%, respectively. Therefore, the prepared PEI-CaAlg can be considered as a novel, eco-friendly, and cost-effective adsorbent for simultaneous dye and phosphate adsorption. PRACTITIONER POINTS: This study aims to modify the surface of calcium alginate beads with polyethyleneimine (PEI). The adsorption of RBBR and phosphate by the modified alginate beads (PEI-CaAlg) was investigated. PEI is an organic polymer with a linear/branch shape, which can increase the active sites on the adsorbent surface. PEI has one nitrogen atom in every three atoms provides a positive charge that can complex with the negatively charged molecules. The adsorption of RBBR and phosphate were carried out onto PEI-CaAlg.

Enhanced Adsorption of Rhodamine B on Modified Oil-Based Drill Cutting Ash: Characterization, Adsorption Kinetics, and Adsorption Isotherm

In this paper, phosphoric acid (H₃PO₄), hydrochloric acid (HCl), and hydrogen peroxide (H₂O₂) were employed for the modification of oil-based drill cutting ash (OBDCA) for the first time. The adsorption of rhodamine B (RhB) on modified oil-based drill cutting ash (MOBDCA) in an aqueous medium was investigated. H₂O₂-modified OBDCA had the optimal adsorption efficiency for RhB. The physical and chemical properties of MOBDCA were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), ζ-potential, N₂ adsorption-desorption isotherm, and pore size distribution. The effect of the pH value (3-11), reaction time (10-720 min), and initial RhB concentration (10-200 mg/L) on RhB adsorption was discussed. The adsorption kinetics highly fitted with the pseudo-second-order model (R ² > 0.99), which indicated that the adsorption process was dominated by chemisorption. The adsorption isotherm fitted well with the Langmuir and Freundlich models (R ² > 0.97), which indicated the monolayer adsorption process and the heterogeneous adsorption process, respectively. The theoretic adsorption capacity (50 mg/g) for RhB was achieved by H₂O₂-modified OBDCA. This paper provides a promising method of resource utilization of OBDCA to treat organic pollutants.

Removal of Disperse Orange and Disperse Blue dyes present in textile mill effluent using zeolite synthesized from cenospheres

In this research, an efficient, ecofriendly method of using coal fly ash in the form of zeolite to treat wastewater containing dyes was studied. Response surface methodology involving Box-Behnken design was applied to a batch process to evaluate the effect of process parameters such as contact time, dye concentration, agitation speed, pH, and adsorbent dosage onto zeolite. Disperse Orange 25 (DO) dye showed a maximum of 96% removal under optimal conditions of contact time of 119 min, dye concentration of 38.00 mg/L, agitation speed of 158 rpm, pH of 6.10, and adsorbent dosage of 0.67 g/L, whereas 95.23% of Disperse Blue 79:1 (DB) dye removal was observed at adsorbent dose of 1.05 g/L, dye concentration of 26.72 mg/L, agitation speed of 145 rpm, pH of 5.68, and contact time of 122 min. It was concluded that cenosphere-derivatized zeolite adsorbent is efficient, ecofriendly, and economical and has high potential for the removal of DO and DB dyes from aqueous solutions.

Adsorption of Congo Red on Pb doped FexOy: experimental study and theoretical modeling via double-layer statistical physics models

Size-controlled Pb_0.06Fe_0.7O₃ nanoparticles (Pb-FeONPs) were fabricated by the thermal co-precipitation method and characterized by FE-SEM, EDX, XRD, and IR techniques. The SEM and XRD images showed the average size distribution and average crystallite size of 19.21 nm and 4.9 nm, respectively. The kinetic model of Congo Red (CR) adsorption onto Pb-FeONPs was verified and found to be a pseudo-second-order reaction. The Langmuir plot was better fitted (R² = 0.990) than other isotherm models with a Q_max (mg/g) of 500 for Congo Red (CR) dye in 40 min. The double-layer statistical physics model based on two energies was used to calculate the significant parameters. The n (stoichiometric coefficient) values obtained from the statistical physics double-layer model were found to be 0.599, 0.593, and 0.565, which are less than 1, indicating the multi-docking process. The regeneration of Pb-FeONPs was used for up to 5 cycles effectively, making the material highly economical. The Pb-FeONPs were fruitfully applied for the removal of CR dye from wastewater on a laboratory and industrial scale.

Adsorption of toxic dye Eosin Y from aqueous solution by clay/carbon composite derived from spent bleaching earth

The environmentally friendly clay/carbon composite (SBE/C) was prepared by one-step pyrolysis under N₂ atmosphere at 700°C of spent bleaching earth (SBE) from the industrial waste of the refined oil industry. SBE/C was tested to remove anionic dye Eosin Y from aqueous water. The results revealed that SBE/C had larger specific surface area than SBE, and the equilibrium adsorption capacity of SBE/C (11.15 mg/g) was about 3 times than that of SBE (4.04 mg/g). The adsorption process was found to be exothermic and spontaneous. The adsorption capacity of SBE/C was independent on pH (5-12), and exhibits satisfactorily recyclable performance. Combined with characterization analysis, the adsorption mechanism likely includes electrostatic interaction, hydrogen bonding, hydrophobic interaction, halogen bonding, and π-π interaction. Overall, this exploration of SBE/C might open a window to the design of an efficient and low-cost adsorbent for Eosin Y dye elimination from wastewater. PRACTITIONER POINTS: The resource utilization of industrial waste SBE was achieved. SBE/C was synthesized and tested to adsorb Eosin Y for the first time. SBE/C had characteristics with porous structure and large surface area. pH had little effect on adsorption capacity of SBE/C for Eosin Y. SBE/C exhibited potential for dye elimination from wastewater.