Cements and adhesives for all-ceramic restorations

Bacterial Adhesion and In Situ Biodegradation of Preheated Resin Composite Used as a Luting Agent for Indirect Restorations

OBJECTIVE

To evaluate surface roughness and bacterial adhesion after in situ biodegradation of the cementation interface of indirect restorations cemented with preheated resin composite.

METHODS AND MATERIALS

Resin composite blocks (Z250XT/3M ESPE) were cemented to bovine enamel (7 × 2.5 × 2 mm) using preheated microhybrid resin composites: (1) Filtek Z100 (3M ESPE) (Z100); (2) Gradia Direct X (GC America) (GDX); and (3) Light-cured resin cement RelyX Veneer (3M ESPE) (RXV) (n=21). The resin composites were preheated on a heating device (HotSet, Technolife) at 69°C for 30 minutes. Disk-shaped specimens (7 × 1.5 mm) were made for biodegradation analysis with the luting agents (n=25). The in situ phase consisted of 20 volunteers' using an intraoral palatal device for 7 days. Each device had six cylindrical wells for the blocks and the disk-shaped specimens. Biodegradation was evaluated through surface roughness (Ra), scanning electron microscopy (SEM) micromorphological analysis, and colony-forming unit (CFU) count. The film thickness of the luting agents was also measured under stereomicroscopy.

RESULTS

Increased surface roughness was observed after the cariogenic challenge without differences between the luting agents. Higher variation and surface flaws suggestive of particulate detachment were observed for Z100. No differences were observed in CFU counts.

CONCLUSIONS

All materials underwent surface biodegradation, and the surface roughness of the resin cements was similar to or lower than that of the preheated resin composites. The resin composites' film thickness was thicker than that of the resin cement. Clinicians should be aware of these factors when choosing the use of preheated resin composite since it can lead to reduced longevity of the cementation interface and, therefore, restorations.

Medium-term evaluation of the bond strength and dentin penetration of self-adhesive resin cements to root dentin

BACKGROUND

Medium-term evaluate the bond strength and tag formation in root dentin using self-adhesive cements Maxcem Elite (MCE), Relyx U200 (RU2), SeT PP (SPP) and Megalink (MGL) compared to conventional cement Relyx ARC (ARC) for glass fibre post cementation.

MATERIALS AND METHODS

One hundred bovine incisors roots were endodontically treated and divided into 5 groups (n = 20) according to the cementation system: MCE, RU2, SPP, MGL and ARC. All cementation systems were evaluated at 24 h (1) and 12 months (2) after post cementation. Specimens from the cervical, middle and apical thirds of the root were submitted to push-out bond strength test and confocal laser microscopy to verify the dentin penetration. The adhesive failure mode was classified as adhesive, cohesive and mixed. Data were analysed by one-way ANOVA and Tukey tests (α = 5%).

RESULTS

ARC-1 and ARC-12 showed the highest bond strength (P < 0.05). ARC showed the greatest tag extension, regardless of the third (P < 0.05). The most frequent failure mode in the 24-h analysis was cohesive, regardless of the cement used. For the 12-month analysis, mixed failure was the most frequent.

CONCLUSION

Conventional cement (ARC) showed the highest bond strength and tag extension, regardless of the evaluation period. In all cementation systems, the bond strength decreased after 12 months. © 2023 Australian Dental Association.

A new method of adhesive system application improves the bond strength between fiber post and root dentin

This study evaluated a new method of adhesive system application on the bond strength between fiber post and root dentin using two adhesive systems. The canals of sixty bovine incisors were prepared and obturated. The roots were divided into six groups (n=10) according to the adhesive system (Clearfil SE - CSE and Single Bond Universal - SBU) and the application strategy (microbrush - MB; rotary brush - RB; and ultrasonic tip - US). The glass fiber posts were cemented with resin cement (RelyX ARC). The roots were sectioned perpendicularly to their long axis, and three slices per root were obtained. Previously to the push-out test, confocal laser scanning microscopy (CLSM) was performed to illustrate the interfacial adaptation of the cement to the root canal walls. Failure patterns were analyzed with 40x magnification. Shapiro-Wilk indicated a normal distribution of the data. The bond strength values were compared using one-way ANOVA and Tukey's tests. Student's T test analyzed the differences between the adhesive systems within each third and protocol. A significance level of 5% was used. CSE with RB showed higher mean bond strength values compared to MB (conventional technique) (P < 0.05). US application resulted in intermediate bond strength values for CSE (P > 0.05). The application of SBU using RB generated higher mean bond strength values compared to MB and US (P < 0.05). Adhesive failures were predominant (65.5%). CSE and SBU application with the new rotary brush improved the bond strength of fiber posts to root dentin compared to the conventional strategy.

Light Polymerization through Glass-ceramics: Influence of Light-polymerizing Unit's Emitted Power and Restoration Parameters (Shade, Translucency, and Thickness) on Transmitted Radiant Power

Background

This in vitro study assessed light transmission through ceramic discs varying in shade, translucency, and thickness using light-polymerizing units with different radiant power/flux (RP) outputs.

Methods

Disc-shaped specimens (0.5 mm, 1.0 mm, and 2.0 mm) were made from high and low-translucency glass-ceramic ingots (IPS e.max Press) in shades A1 and A4, totaling 60 discs. Two light-polymerizing units with different power outputs were used, and their emission spectra were verified. The transmitted RP values for each ceramic specimen were measured and irradiance and radiant energy influx were calculated. Differences between the light-polymerizing units and the influence of the three ceramic parameters were evaluated using an independent-samples t-test and three-way analysis of variance (ANOVA) tests (α = 0.05).

Results

A statistically significant difference was observed in the mean transmitted RP values between the two light-polymerizing units. Furthermore, the three-way ANOVA test showed a significant effect of shade, translucency, and thickness, as well as a significant interaction between each pair of variables and all three variables on the transmitted RP (P < 0.05).

Conclusions

Despite the significant attenuation in the transmitted RP, especially in ceramics with higher shade chromaticity and thickness and lower translucency, the calculated minimal irradiance values for both light-polymerizing units (their emitted power ≥ 500 mW) were greater than the minimum recommended irradiance threshold (100 mW/cm2). However, the exposure duration needs to be increased to provide the resin with sufficient radiant exposure for adequate polymerization.

Resin cement selection for different types of fixed partial coverage restorations: A narrative systematic review

OBJECTIVE

The aim of this study was to review the selection criteria of resin cements for different types of partial coverage restorations (PCRs) and investigate if the type of restorations or restorative materials affect the type of selected resin cement.

MATERIALS AND METHODS

An electronic search (1991-2023) was performed in PubMed, Medline, Scopus, and Google Scholar databases by combinations of related keywords.

RESULTS

A total of 68 articles were included to review the selection criteria based on the advantages, disadvantages, indications, and performance of resin cements for different types of PCRs.

CONCLUSIONS

The survival and success of PCRs are largely affected by appropriate cement selection. Self-curing and dual-curing resin cements have been recommended for the cementation of metallic PCRs. The PCRs fabricated from thin, translucent, and low-strength ceramics could be adhesively bonded by light-cure conventional resin cements. Self-etching and self-adhesive cements, especially dual-cure types, are not generally indicated for laminate veneers.

The effect of hydrofluoric acid treatment on the repair strength of polyamide denture base materials: An in vitro study

PURPOSE

Although polymethylmethacrylate (PMMA) dentures can be repaired using autopolymerizing acrylic resin, achieving it using polyamides is difficult. This study aimed to achieve acceptable bond strength using autopolymerizing acrylic resin by applying surface treatments to the polyamide denture base material.

MATERIALS AND METHODS

Thirty-six disc-shaped samples (27 polyamide, 9 PMMA) were prepared. Based on the surface treatment applied, the polyamide samples were divided into three groups: No surface treatment (n = 9), tribochemical silica coating + silane coupling agent (n = 9), and 9% hydrofluoric acid + tribochemical silica coating +silane coupling agent (n = 9). PMMA specimens received no surface treatment. Polyamide and PMMA surfaces had auto-polymerizing acrylic resin bonded on them, and then a shear bond strength test was performed between them after aging. The Kruskal-Wallis test was used, and statistical significance was set at p < 0.05.

RESULTS

PMMA had the highest shear bond strength, the untreated polyamide group had the lowest shear bond strength, and the difference was significant (p < 0.05). The group treated with 9% hydrofluoric acid, tribochemical silica coating, and silane coupling agent exhibited the highest shear bond strength of the polyamide groups, and the bond strength in this group was comparable to the PMMA specimens (p > 0.05).

CONCLUSIONS

The polyamide denture repair strength can be improved by 9% hydrofluoric acid, tribochemical silica coating, and silane coupling agent application to the polyamide surface.

Adhesive bond strength of monolithic zirconia ceramic finished with various surface treatments

BACKGROUND

This study aimed to investigate different surface treatments thought to increase the bond strength between zirconia ceramic and adhesive resin cement.

METHODS

The samples were prepared in 15 × 10 × 2 mm dimensions by cutting off monolithic zirconia ceramic blocks (Incoris TZI; Sirona, Germany). Surface roughness measurements were made with a profilometer, the average surface roughness (Ra1) was recorded, and five different surface treatments were applied. Group 1: Control group. No surface treatment was applied. Group 2: Sandblasted with Al2O3 under pressure of 50 μm. Group 3: Sandblasted with 30 μm Al2O3 - SiOx under pressure, then tribochemical silica coating, silane bonding agent, and ceramic primer were applied. Group 4: Samples were etched in a hot acid solution containing methanol, HCl, and chloride at 100 °C. Group 5: Samples were coated in a solution containing Grade C Aluminum Nitrite at 75 °C for 15 Sects. 12,000 thermal aging was carried out to all samples. Then, samples were bonded to a composite surface (Filtek Z250) with two different types of adhesive cement (Panavia F 2.0, Rely X U200) (n = 10). A load was applied to the samples attached to the Universal Test Device for the SBS, and the SBS was recorded. The surface roughness measurements of all samples were made again, and the average surface roughness Ra2 was recorded. The data was analyzed with a two-way ANOVA test. Bonferroni correction was used for multiple comparisons of the groups. p = 0.005 was accepted as the statistically significant value.

RESULTS

There was no statistically significant difference between the groups in the Ra1 measurements (p = 0.031). There was a statistically significant difference between the Ra2 values of Groups 4 and 5 and the Ra2 values of Groups 1,2 and 3 in the Ra2 measurements (p < 0.001). There was no statistically significant difference between the SBS values of the groups (p > 0.005). Also, there was no statistically significant difference in the SBS values of all groups for the two different cements tested (p > 0.005).

CONCLUSIONS

None of the surface treatments applied to monolithic zirconia ceramic samples increased the SBS between ceramic and adhesive resin cement.

Effect of Storage Temperature on Selected Strength Parameters of Dual-Cured Composite Cements

Direct restorations are currently the most popular restorations used in dental prosthodontics. Due to the increased requirements for materials used in the fabrication of fixed restorations, there is a need for evaluation of strength parameters of these materials, including dental cements. The present study investigated the change in selected strength parameters of four dual-cured composite cements as a function of storage temperature. The following were investigated: three-point flexural strength (FS), flexural modulus in bending (FM), diametral tensile strength (DTS) and Vickers hardness (HV). Four dual-cured composite cements were tested, i.e., Multilink Automix (Ivoclar Vivadent), seT PP (SDI), MaxCem (Kerr), and Bifix Hybrid Abutment (VOCO). Each of the tested cements was stored for 7 days at one of the selected temperatures: 8 °C, 15 °C, 25 °C, or 35 °C, before the samples were made. Strength properties (DTS, FS) are not strongly dependent on the storage temperature in the range of 8-35 °C. Some statistical differences were observed between the hardness of MaxCem and Multilink Automix storage in various temperatures. FS and FM were lowest for Bifix Hybrid Abutment, MaxCem and Multilink Automix storage at 25 °C, and highest for Bifix Hybrid Abutment, MaxCem, and seT PP stored in 35 °C. The cement with the highest filler content (70% by weight) showed the highest FS and HV.

Effects of Surface Treatments and Cement Type on Shear Bond Strength between Titanium Alloy and All-Ceramic Materials

This study aimed to evaluate the effects of surface treatments and resin cement on the adhesion of ceramic and ceramic-like materials to titanium. A total of 40 specimens (5 mm diameter) of each material (lithium disilicate glass ceramic (LDGC-IPS e.maxCAD), lithium silicate glass ceramic (LSGC-VITA Suprinity) and a polymer-infiltrated ceramic network (PICN-Vita Enamic)) were fabricated using CAD/CAM technologies. In total, 120 titanium (Ti) specimens were divided into 12 groups, and half of the titanium specimens were tribochemically coated using CoJet. The titanium and all-ceramic specimens were cemented using either Self-curing adhesive cement (SCAC-Panavia 21) or a Self-curing luting composite (SCLC-Multilink Hybrid Abutment). After 5000 cycles of thermal aging, the shear bond strength (SBS) test was conducted using a universal testing machine. The failure modes of the specimens were analyzed using stereomicroscopy, and additionally, the representative specimens were observed using Scanning Electron Microscopy. ANOVA was used for the statistical analysis (p < 0.05). The post-hoc Duncan test was used to determine significant differences between the groups. The mean SBS values (mean ± STD) ranged from 15 ± 2 MPa to 29 ± 6 MPa. Significantly higher SBS values were acquired when the titanium surface was tribochemically coated (p < 0.05). The SCLC showed higher SBS values compared to the SCAC. While the LDGC showed the highest SBS values, the PICN presented the lowest. The tribochemical coating on the cementation surfaces of the titanium increased the SBS values. The specimens cemented with the SCLC showed higher SBS values than those with the SCAC. Additionally, the SCLC cement revealed a more significant increase in SBS values when used with the LDGC. The material used for restoration has a high impact on SBS than those of the cement and surface conditioning.

Effect of ceramic primers with different chemical contents on the shear bond strength of CAD/CAM ceramics with resin cement after thermal ageing

BACKGROUND

This study evaluated the effect of ceramic primers containing 10-methacryloyloxydecyl phosphate (10-MDP) and γ-methacryloxypropyl trimethoxysilane (γ-MPTS) agents on the shear bond strength (SBS) of CAD/CAM ceramics with different chemical structures and resin cement.

METHODS

A total of 640 CAD/CAM ceramic specimens were obtained from Vita Mark II (VM), IPS E.max CAD (EM), Vita Suprinity (VS) and Vita Enamic (VE). The specimens were divided into two groups: etched with hydrofluoric acid (HF) and unetched. Each group was treated with a different ceramic primer (Clearfil Ceramic Primer Plus, G-Multi Primer and Monobond S), except for an untreated group (n = 10). After ceramic primers and resin cement were applied to each ceramic surface, half of the specimens were thermally aged at 10,000 cycles, 5-55 ± 1 °C, with a dwell time of 30 s. The SBS was tested with a universal testing machine at a 0.5 mm/min crosshead speed. Data were analysed by using statistical software (SPSS 20). Normal data distribution was checked with the Shapiro‒Wilk test. Three-way ANOVA was used to analyse the difference between the numeric data of the HF etched and thermally aged groups. A post hoc Tukey test was applied in the paired comparison of significant difference. The statistical significance level was accepted as p < 0.05.

RESULTS

The highest SBS values were obtained in the HF etched G-Multi primer applied nonaged EM group (28.3 ± 2.62 MPa), while the lowest values were obtained in the nonetched and thermally aged EM group that received no treatment (2.86 ± 0.04 Mpa). The SBS significantly increased in all specimens on which the ceramic primer was applied (p < 0.001). Thermal ageing had a significant negative effect on the SBS values in all groups (p < 0.001).

CONCLUSION

The positive combined effects of the 10-MDP and γ-MPTS agents resulted in a significant increase in the bonding strength of the resin cement to the CAD/CAM ceramics. In addition, the increase in the amount of inorganic filler provided a favourable effect on durable adhesion.

Clinical performance of lithium disilicate and zirconia CAD/CAM crowns using digital impressions: A systematic review

PURPOSE

The purpose of this systematic review was to compare the clinical performance of lithium disilicate (LDS) and zirconia (Z) single crowns manufactured by computer-aided design/computer-aided manufacturing (CAD/CAM) systems using intraoral optical scanners (IOS).

MATERIALS AND METHODS

An electronic search for articles published between January 2012 and January 2022 in the English language was performed with the Medline/Pubmed database under the guidelines of Preferred Reporting Items for Systemic Reviews and Meta-analysis (PRISMA). The specific search terms used were "zirconia", "lithium disilicate", "CAD/CAM", "intraoral optical scanner", and "survival".

RESULTS

The initial electronic search resulted in 278 articles. Most of the resulting articles were excluded, six clinical studies addressing the clinical outcomes of Z and LDS crowns fitted the inclusion criteria and were selected for review. Of these six studies, three were randomised controlled trials, two were retrospective studies, and one was a prospective study. To quantify the clinical performance of the crowns several parameters were recorded, including fractures, endodontic complications, periodontal complications, technical complications, aesthetic complications, and biological complications. It was noted that the most common technical complication of Z and LDS crowns was chipping at a rate of 1.4% and 5% respectively. Regarding Z crowns, aesthetic concerns were the most frequently observed complication.

CONCLUSION

The outcomes of this systematic review indicate that Z and LDS crowns display a similar incidence of periodontal and endodontic complications when compared to metal-ceramic crowns, suggesting that these all-ceramic materials are viable alternatives. The incidence of chipping was higher in LDS crowns compared to other materials, while Z crowns were inferior in terms of aesthetics.

Luting indirect restorations with resin cements versus composite resins: Effects of preheating and ultrasound energy on film thickness

OBJECTIVE

This study aims to evaluate and compare the film thickness obtained with a resin cement and two composite resins, preheated and/or ultrasonically vibrated, as luting agents.

MATERIALS AND METHODS

One hundred and twenty-six (126) pairs of resin discs were randomly assigned to six experimental groups (n = 21) according to luting agent (Variolink Esthetic LC, IPS Empress Direct or Estelite Omega) and cementation technique (preheating at 68°C and/or ultrasonic vibration). Specimens were luted by applying a controlled force. Following sectioning and film thickness measurement through field emission gun scanning electron microscopy, statistical analysis was carried out considering a 5% significance level.

RESULTS

Statistically significant lower film thickness was observed in Variolink Esthetic LC group when compared to all composite resin groups (p < 0.001), except IPS Empress Direct preheated and ultrasonically vibrated group (p = 0.073). IPS Empress Direct with ultrasonic vibration yielded statistically lower film thickness values than Estelite Omega groups, regardless of luting technique (p < 0.05). Ultrasonically vibrated Estelite Omega groups showed statistically lower film thickness values than solely preheated groups (p < 0.05).

CONCLUSIONS

Both Variolink Esthetic LC and IPS Empress Direct preheated and ultrasonically vibrated provided the lowest film thickness. The addition of ultrasonic vibration during cementation proved to be effective in reducing film thickness of both tested composite resins.

CLINICAL SIGNIFICANCE

The cementation technique will have variable results depending on the luting material. Adhesive cementation protocols with composite resins should mainly consider ultrasonic vibration, but also preheating, as strategies for reducing film thickness. The tested resin cement, alongside with IPS Empress Direct composite resin preheated and ultrasonically vibrated, provided the lowest film thickness among the tested materials and techniques.

Surface Treatment and Cementation of Lithium Silicate Ceramics Containing ZrO2

Objective

To evaluate the effect of different surface treatments on the shear bond strength (SBS) of lithium silicate (LS) and lithium disilicate (LD) ceramics, after thermocycling.

Methods and Materials

For SBS test, 72 ceramic blocks (18×14×2 mm) were made (24 blocks from each ceramic material): VITA Suprinity (LSS), Celtra Duo (LSC), and Lithium disilicate (LD). The blocks were polished with sandpaper of increasing grit (#280, #400, #800, and #1200) and embedded in chemically activated acrylic resin. Afterwards, they were randomly divided into 12 groups (6 blocks per group) according to: “Ceramic” (LD, LSC, and LSS) and “Surface treatment” (HFS: hydrofluoric acid + silane; MEP: Monobond Etch & Prime/Ivoclar). From each treated surface ceramic block, four dual-curing resin cement cylinders (RelyX U200, 3M Oral Care) were prepared using a Tygon tube (Ø=3 mm and h=2 mm) and light cured for 40 seconds (1000 mW/cm2) (N=288/n=24). All specimens were submitted to thermocycling (10,000 cycles, 5°C and 55°C, 30 seconds) and then to SBS test at a crosshead speed of 1 mm/min using a 50-kgf load cell. Forty-five additional blocks were made for roughness and SEM analysis. Failure mode was also performed. The data (MPa) were statistically analyzed by oneway analysis of variance (ANOVA), Tukey test (5%), and Weibull analysis. The Ra was analyzed by Kruskal–Wallis and Dunn Test (5%). The other variables were analyzed qualitatively.

Results

ANOVA revealed that “surface treatment” was significant for all ceramic materials (p&lt;0.05). The LD-HFS (18.66±3.49), LSC-HFS (16.81±2.62), and LSS-HFS (16.33±3.08) groups had significantly higher SBS than the LD-MEP (7.00±4.2), LSC-MEP (14.12±3.51), and LSS-MEP (13.87±2.52) groups. Complete adhesive failures at the cement– dentin interface were more frequent. Weibull modulus was superior for the LD-HFS (6.22), LSC-HFS (8.8), and LSS-HFS (7.4) groups.

Conclusion

HF followed by silanization is the most suitable surface treatment for the cementation of LS and LD glass ceramics.

Evaluation of Micro-Shear Bond Strength of Four Different CAD-CAM Polymer-Infiltrated Ceramic Materials after Thermocycling

PURPOSE

To evaluate the bond strength of three monolithic hybrid ceramics/resin nanoceramics and a zirconia-reinforced lithium silicate to resin cement after thermocycling.

MATERIALS AND METHODS

Using four materials, including Vita Enamic (VITA Zahnfabrik), Lava Ultimate (3M ESPE), Crystal Ultra (Digital Dental), and Vita Suprinity (VITA Zahnfabrik), 64 specimens were prepared with dimensions of 4mm×3mm×1.5mm. Vita Suprinity samples were sintered at 840°C for 8 min. After polishing and cleaning all the samples in each group (n = 16), they were subjected to their recommended surface treatment: 10% hydrofluoric acid for Vita Enamic (60s) and Vita Suprinity (20s); air abrasion of Lava Ultimate and Crystal Ultra with 50μ Al₂ O₃ particles. Then, tygon tubes were filled with dual cure resin cement (Panavia F2.0), cured and then subjected to thermal cycling (2000 cycles; 5-55°C). The micro-shear bond strength was measured using micro-tensile testing machine. The data were analyzed using Welch and Games-Howell tests (α = 0.05). The mode of failure was also evaluated using a stereomicroscope.

RESULTS

The highest and the lowest mean micro-shear bond strength belonged to the Crystal Ultra (7.71 ±1.54 MPa) and Vita Suprinity (4.73 ±1.87 MPa) groups, respectively. The differences between groups were significant and Crystal Ultra had higher bond strength in comparison to all three materials (p<.05).

CONCLUSION

Hybrid ceramics showed higher bond strength to resin cements in comparison to resin nanoceramics and zirconia-reinforced lithium silicate materials. This article is protected by copyright. All rights reserved.

The Effect of Dentin Treated with Calcium Phosphate Desensitizer on Shear Bond Strength with Different Resin Cement: An In Vitro Study

Aim:

The aim of this study was to evaluate the effect of calcium phosphate based desensitizing agent on shear bond strength of self-etch/adhesive resin cements to dentin.

Materials and Methods:

Eighty dentin specimens were prepared from freshly extracted human third molar teeth and were classified, randomly ( n = 20). Half of groups were treated with calcium phosphate based Teethmate Desensitizer and then Panavia V5, RelyX Ultimate (containing self-etch primer), Panavia SA, and RelyX U200 self-adhesive resin cements were luted to all dentin surfaces. All specimens were stored in an incubator at 37°C for 24 h. Shear bond strength was tested by a universal test machine at a 0.5 mm/min crosshead speed. The data were analyzed with a statistical program. Two-way ANOVA was used for statistical differences ( P <.05). Dentin surfaces were examined with scanning electron microscopy (SEM) at x5000 and x10000 magnifications.

Results:

The higher shear bond values were observed in the groups with Teethmate Desensitizer applied and cemented with self-etch (16.05 ± 6.24 and 14.73 ± 4.75), whereas the lowest bonding values were observed in the groups with self-adhesive resin cement without Teethmate Desensitizer (3.73 ± 0.77 and 5.85 ± 4.19; P <.001). As the main effect of the treatment, the bond strength was 9.39 ± 6.04 in the control group, whereas it was 13.49 ± 5.44 in the Teethmate applied groups ( P <.05)

Conclusions:

Calcium phosphate desensitizer did not adversely effected shear bond strength of self-etch/adhesive resin cements to dentin. It even significantly increased the shear bond strength of self-adhesive resin cements.

UV-Mediated Photofunctionalization of Indirect Restorative Materials Enhances Bonding to a Resin-Based Luting Agent

Purpose

The potential of UV-mediated photofunctionalization to enhance the resin-based luting agent bonding performance to aged materials was investigated.

Methods

Sixty samples of each material were prepared. Yttria-stabilized zirconia (YZr) and Pd-Au alloy (Pd-Au) plates were fabricated and sandblasted. Lithium disilicate glass-ceramic (LDS) was CAD-CAM prepared and ground with #800 SiC paper. Half of the specimens were immersed in machine oil for 24 h to simulate the carbon adsorption. Then, all of the specimens (noncarbon- and carbon-adsorbed) were submitted to UV-mediated photofunctionalization with a 15 W UV-LED (265 nm, 300 mA, 7692 μW/cm²) for 0 (control groups), 5, and 15 min and subjected to contact angle (Ɵ) measurement and bonded using a resin cement (Panavia™ V5, Kuraray Noritake, Japan). The tensile bond strength (TBS) test was performed after 24 h. The Ɵ (°) and TBS (MPa) data were statistically analyzed using two-way ANOVA and Bonferroni correction tests (α = 0.05).

Results

In the carbon-adsorbed groups, UV-mediated photofunctionalization for 5 min significantly decreased Ɵ of all materials and increased TBS of YZr, and UV for 15 min significantly increased the TBS of LDS and Pd-Au. In noncarbon-adsorbed groups, UV-photofunctionalization did not significantly change the Ɵ or TBS except YZr specimens UV-photofunctionalized for 15 min.

Conclusion

UV-mediated photofunctionalization might have removed the adsorbed hydrocarbon molecules from the materials' surfaces and enhanced bond strengths of Panavia™ V5 to YZr, LDS, and Pd-Au. Additionally, UV-mediated photofunctionalization improved the overall TBS of YZr. Further investigation on the optimum conditions of UV photofunctionalization on indirect restorative materials should be conducted.

Influence of feldspar ceramic thickness on the properties of resin cements and restorative set

This in vitro study evaluated the influence of feldspathic ceramic thickness on the properties of light- and dual-cured resin cements. For each cement (RelyX Veneer, Allcem Veneer, RelyX Ultimate, and Allcem Dual), three ceramic specimens were prepared, with seven thicknesses for each (0.5, 1.0, 1.5, 2.0, 2.5, 3.0, and 3.5 mm). The degree of conversion, Vickers microhardness, irradiance power, color variation (ΔE₀₀ ), and translucency parameters were assessed. Microhardness and irradiance power were analyzed using analysis of variance (ANOVA) with post hoc Tukey's test, while ΔE₀₀ , translucency parameters, and degree of conversion were analyzed using ANOVA of ranks with post hoc Duncan's Multiple Range Test. The relationship between each of the dependent variables (degree of conversion, ΔE₀₀ , and translucency parameter tests) and the specimen thickness was described using linear regression for each of the four resin cements. The significance level for all analyses was set at 5%. RelyX Ultimate yielded the lowest degree of conversion values among all resin cements. Allcem Veneer produced the lowest microhardness values, without statistical differences between thicknesses, of up to 1 mm. Allcem Dual produced the highest ΔE₀₀ and translucency parameter values. Feldspathic ceramic thickness influenced the mechanical properties of resin cements and optical aspects of the restorative set.

Influence of photodynamic therapy and different lasers Er,Cr:YSGG and Er,YAG on dentin conditioning bonded to conventional and bioactive cement

AIM

The aim of the present study was to evaluate the bond integrity of bioactive cement (BA_c) in contrast to conventional cement Calibra (C) after dentin treated with different surface conditioners (PDT, EYL, ECL) MATERIALS AND METHODS: Sixty non-carious permanent mandibular molars were disinfected and embedded in acrylic resin till cement-o-enamel junction. For homogeneity the buccal surface were grounded and polished. Samples were categorized into three main groups based on conditioning technique. Samples in group 1 and 2 dentin conditioned with Er,Cr:YSGG (ECL), group 3 and 4 surface treated with Er:YAG (EYL) and group 5 and 6 treated with photodynamic therapy (PDT).On conditioned surface bonding agent was applied and light cured. Samples from group 1,3,5 were bonded to Calibra (C). Whereas, specimens in group 2,4,6 were conditioned with bioactive cement (BA_c) and subjected to ageing followed by shear bond strength testing (SBS) in universal testing machine. To detect significance difference between means of different groups analysis of variance (ANOVA) was performed followed by Tukey's post-hoc tests.

RESULTS

The maximum SBS was displayed in group 1, dentin conditioned with ECL and bonded to C (20.23 ± 0.47 MPa). Whereas, group 6, PDT of dentin to BA_c demonstrated lowest bond integrity among experimental groups (12.97 ± 0.25 MPa). Bond strength of group 1, ECL-C (21.55 ± 3.08 MPa) and group 3 EYL-C (19.11 ± 0.65 MPa) were comparable (p > 0.05). Group 5 samples treated with PDT, MB-C (13.41±0.32 MPa) and group 6, MB-BA_c (12.97 ± 0.25 MPa) were also comparable (p > 0.05) CONCLUSION: BAc bonded to dentin after surface conditioning with ECL, EYL and PDT presented lower SBS in comparison to conventional cement C. Further studies are required to extrapolate the current findings.

Time-Stability Dispersion of MWCNTs for the Improvement of Mechanical Properties of Portland Cement Specimens

This study shows the energy optimization and stabilization in the time of solutions composed of H2O + TX-100 + Multi-Wall Carbon Nanotubes (MWCNTs), used to improve the mechanical properties of Portland cement pastes. For developing this research, sonication energies at 90, 190, 290, 340, 390, 440, 490 and 590 J/g are applied to a colloidal substance (MWCNTs/TX-100 + H2O) with a molarity of 10 mM. Raman spectroscopy analyses showed that, for energies greater than 440 J/g, there are ruptures and fragmentation of the MWCNTs; meanwhile at energies below 390 J/g, better dispersions are obtained. The stability of the dispersion over time was evaluated over 13 weeks using UV-vis spectroscopy and Zeta Potential. With the most relevant data collected, sonication energies of 190, 390 and 490 J/g, at 10 mM were selected at the first and the fourth week of storage to obtain Portland cement specimens. Finally, we found an improvement of the mechanical properties of the samples built with Portland cement and solutions stored for one and four weeks; it can be concluded that the MWCNTs improved the hydration period.

Evaluation of physical-mechanical properties of self-adhesive versus conventional resin cements

Aim: The purpose of this study was to compare the microhardness, diametral tensile strength, compressive strength and the rheological properties of self-adhesive versus conventional resin cements. Methods: Specimens of a conventional (RelyX ARC) and 3 self-adhesive (RelyX U200, Maxcem Elite, Bifix SE) types of resin cements were prepared. The Knoop test was used to assess the microhardness, using a Microhardness Tester FM 700. For the diametral tensile strength test, a tensile strength was applied at a speed of 0.6 mm/minute. A universal testing machine was used for the analysis of compressive strength and a thermo-controlled oscillating rheometer was used for the Rheology test. One-way ANOVA and Tukey’s test (α=0.05) were used for data analysis. Results: According to microhardness analysis, all the cements were statistically similar (p>0.05), except for Maxcem that presented lower hardness compared with the other cements in relation to the top surface (p<0.05). In the diametral tensile strength test, Relyx U200 and RelyX ARC cements were statistically similar (p>0.05), presented higher value when compared to the Maxcem and Bifix cements (p<0.05). The compressive strength of RelyX ARC and Maxcem Elite cements was statistically higher than RelyX U200 and Bifix cements (p<0.05). Regarding the rheology test, Maxcem Elite and RelyX ARC cements showed a high modulus of elasticity. Conclusions: The self-adhesive cements presented poorer mechanical properties than conventional resin cement. Chemical structure and types of monomers employed interfere directly in the mechanical properties of resin cements.

Dentin to dentin adhesion using combinations of resin cements and adhesives from different manufacturers - a novel approach

Aims

The aims of this study were to present a novel method to analyse dentin bond strength and to evaluate the bond strength of combining adhesive systems and resin cement from different manufacturers.

Methods

Human wisdom teeth were ground flat to the dentin on parallel surfaces and axially cut into two parts. Dentin cylinders (Ø 3 mm) were drilled from one half of each tooth. The other half from each tooth was embedded in epoxy resin with the dentin surface exposed. The specimens were ground with silicone carbide paper and the dentin cylinders were cemented onto the dentin surface of the other half of the same tooth.

Materials: Resin cement and adhesive systems from three different manufacturers were used in various combinations (n = 8 per group). Cement and adhesive from the same manufacturer served as control. Shear bond strength (SBS) was measured and fracture modes were registered.

Results and conclusions: The highest median SBS value was found in a bonding combination between cement and a non-corresponding adhesive (33.1 MPa) and one of the lowest values was found in one of the controls (15.3 MPa). Cohesive fractures were most frequent. The results indicated that combining adhesive and cement from different manufacturers did not compromise the dentin bonding. The novel test method is recommended for evaluating dentin bonding.

[Development of novel self-adhesive resin cement with antibacterial and self-healing properties]

OBJECTIVE

This study aimed to develop novel self-adhesive resin cement with antibacterial and self-healing properties. Furthermore, the dentin bonding strength, mechanical properties, self-healing efficiency, and antibacterial property of the developed cement were measured.

METHODS

Novel nano-antibacterial inorganic fillers that contain quaternary ammonium salts with long-chain alkyls were synthesized. These fillers were added into self-adhesive resin cement containing self-healing microcapsules at mass fractions of 0, 2.5%, 5.0%, 7.5%, or 10.0%. The dentin shear bonding test was used to test the bonding strength, whereas the flexural test was used to measure the flexural strength and elastic modulus of the cement. The single-edge V-notched beam method was used to measure self-healing efficiency, and human dental plaque microcosm biofilms were chosen to calculate the antibacterial property.

RESULTS

The dentin shear bond strength significantly decreased when the mass fraction of the nano-antibacterial inorganic fillers in the novel cement reached 7.5% (P<0.05). The incorporation of 0, 2.5%, 5.0%, 7.5%, or 10.0% mass fraction of nano-antibacterial inorganic fillers did not adversely affect the flexural strength, elastic modulus, fracture toughness, and self-healing efficiency of the cement (P>0.1). Resin cement containing 2.5% mass fraction or more nano-antibacterial inorganic fillers significantly inhibited the metabolic activity of dental plaque microcosm biofilms, indicating strong antibacterial potency (P<0.05).

CONCLUSIONS

The novel self-adhesive resin cement exhibited promising antibacterial and self-healing properties, which enable the cement to be used for dental applications.

The Effect of Viscosity and Application Mode of Phosphoric Acid on Bond Strength of GlassFiber Post

Background

When a phosphoric acid is used, before applying an adhesive system, it is known that obtaining an effective adhesion to the root canal walls is a challenge. The aim of the present study was to evaluate the influence of phosphoric acid viscosity and application mode on the push-out bond strength (BS) values of fiberglass post to root dentin. The conditioning pattern on the root dentin was also evaluated.

Materials and Methods

The roots of 44 endodontically treated premolars were divided into 4 groups, of eleven teeth each, according to the combination of the main factors: phosphoric acid viscosity (liquid or gel) and application mode (passive or sonic). After application of the two-step etch-and-rinse adhesive system, the fiberglass posts were cemented with a dual-cure resin-cement. Roots were sectioned transversely into six 1-mm slices for push-out BS test at 0.5 mm/min. Some roots of each group were selected for evaluation of the conditioning pattern by scanning electron microscopy. BS results (three-way ANOVA and Tukey’s test) and the conditioning pattern (Kruskal–Wallis test and Mann–Whitney test) were statistically evaluated (α= 0.05).

Results

The highest BS value was observed with a liquid phosphoric acid under sonic application mode (p < 0.05), being all other groups similar to one another (p < 0.05). Also, the highest BS value was observed in the cervical third, followed by the medium and the apical thirds (p < 0.05). The sonic application produced better smear layer removal and opening of dentinal tubules for both viscosities (p = 0.015).

Conclusion

A better bonding of fiberglass posts to root canals can be achieved when the post spaces are conditioned with a liquid phosphoric acid under sonic application.

Effect of experimental resin cements containing thio-urethane oligomers on the durability of ceramic-composite bonded interfaces

Thio-urethane oligomers improve conversion and mechanical properties of resin cements. The objective of this study was to evaluate the effect of resin cements formulated with thio-urethane (TU) oligomers on microtensile bond strength (µTBS) of ceramics to composites subjected to thermal/mechanical cycling. Methods: BisGMA/UDMA/TEGDMA (50/30/20 wt%) containg 0 (control, EC) or 20 wt% aliphatic or aromatic thiourethane (HDDI and BDI, respectively) were mixed with CQ/amine (0.2/0.8 wt%) and 25 wt% 0.7um Ba glass. Rely X Ultimate (RU-3M ESPE) was used as the commercial control. The cements were sandwiched between ceramic (IPS e.max Press) and resin composite blocks (Filtek Supreme, 3 M-ESPE). Eight bonded blocks were produced per experimental group. Prior to bonding, ceramic surfaces were etched (20 s - 10% HF) and silanized. Composite surfaces were treated with Single Bond Universal (3 M ESPE). Specimens were stored for 24 h in distilled water at 37 °C, and then either tested immediately, or subjected to thermal (10,000, 5 °C and 55 °C) or mechanical cycling (300,000 cycles). Sticks (1 mm², average of 25 sticks per block) were cut and tested for µTBS (1.0 mm/min). Data were analyzed with two-way ANOVA/Tukey's test (α = 5%). Fracture surfaces were analyzed to determine failure modes. Results: The µTBS for HDDI and RU was significantly higher than BDI and EC cements. BDI led to significantly higher µTBS than EC after 24 h, Tc and Mf. µTBS decreased significantly after thermal/mechanical cycling for all groups. Failure modes were predominantly adhesive or mixed. Significance: The use of selected thio-urethane oligomers was able to increase the µTBS of composite-cement-ceramic specimens. Tc and Mf reduced µTBS for all resins cements.

Effect of Bleaching and Ca(OH)2 Dressing on the Bond Strength of Fiberglass Posts to Root Dentine

Objective The purpose of this study was to evaluate the effect of the intracoronary bleaching and calcium hydroxide (Ca(OH) ₂ ) dressing use, on the bond strength (BS) of fiberglass posts to root dentine.

Materials and Methods After root canal filling of 40 bovine incisors, a 2-mm thick cervical plug was fabricated 2 mm below the cementum–enamel junction. Seven days later, teeth were randomly distributed into four groups ( n = 10), as follows: G1 no bleaching, followed by immediate post cementation; G2 bleaching and immediate post cementation; G3 bleaching, dressing with Ca(OH) ₂ for 7 days, and post cementation; and G4 bleaching, no dressing, and post cementation after 7 days. The roots were transversally cut into 1-mm thick slices to perform the push-out test (0.5 mm/min). Failure modes were assessed under scanning electron microscopy.

Statistical Analysis The analysis of variance (two-way ANOVA) was performed, followed by the supplementary Tukey multiple comparison test ( a = 5%).

Results No significant difference for BS was observed among groups. Considering the different root thirds, G1 had higher BS values for the cervical third in comparison with the apical one ( p < 0.05). The most frequent failure modes were adhesive between cement/dentine (G1); cohesive at the post (G2 and G3), and mixed (G4).

Conclusions The BS of the fiberglass posts to root dentine was not affected by the intracoronary bleaching and the use of Ca(OH) ₂ dressing.

Influence of N-(2-hydroxyethyl)acrylamide addition in light- and dual-cured resin cements

OBJECTIVE

To develop experimental light-cured (L) and dual-cured (D) resin cements containing N-(2-hydroxyethyl)acrylamide and evaluate the physicochemical and optical properties.

METHODS

Experimental resin cements were formulated using bisphenol A-glycidyl dimethacrylate (70%) and 2-hydroxyethyl methacrylate (30%), in the control groups, and, bisphenol A-glycidyl dimethacrylate (70%) and N-(2-hydroxyethyl)acrylamide (30%). Polymerization kinetics were evaluated by differential scanning calorimetry (n = 3), softening in solvent (ΔKHN) evaluated by the difference of Knoop microhardness before (KHN₁) and after (KHN₂) ethanol solution immersion (n = 5), radiopacity in mmAl (n = 5), film thickness (n = 3) and color stability were evaluated. Mechanical properties as ultimate tensile strength (UTS) and micro-shear bond strength (μSBS) were analyzed immediately and after 6 months. Results were analyzed using ANOVA, Tukey's test and Student's t-test (α = 0.050).

RESULTS

The L_HEAA1 group had no statistical difference from the control group regarding polymerization kinetics, KHN₁, ΔKHN and color stability (p > 0.050). In dual-cured cements, the acrylamide groups presented a lower degree of conversion and higher ΔKHN than the D_HEMA0.6 group, which obtained a higher rate of polymerization (p < 0.050). There was no statistical difference in radiopacity and film thickness (p > 0.050). Dual-cured cements with N-(2-hydroxyethyl)acrylamide showed higher color change than methacrylates. Immediate mechanical properties were lower for acrylamide groups (p < 0.050), with higher hydrolytic stability.

CONCLUSIONS

The addition of N-(2-hydroxyethyl)acrylamide negatively affected the properties of the dual-cured resin cements. LHEAA1 did not differ in physicochemical and optical properties from the control, with higher hydrolytic stability.

CLINICAL SIGNIFICANCE

The results of the study indicate that acrylamides increased mechanical properties over time independently of the curing system mode, with more hydrolytic stability. The clinical performance of experimental resin cements should be evaluated.

Influence of the composition and shades of ceramics on light transmission and degree of conversion of dual-cured resin cements

Objective

Since the transmittance of ceramics can influence the degree of conversion (DC) of resin cements, ceramics composition and shade should be considered in the selection of resin cement. This in vitro study aimed to evaluate the effect of the transmittance of different composition, opacities and shades of ceramics on the degree of conversion of two dual-cured resin cements.

Methodology

Sixty discs were prepared from low translucency (LT) and medium opacity (MO) lithium disilicate ceramic, and zirconia ceramic (Z). Each group was subdivided into 5 subgroups (n=4) in shades A2, A3.5, B2, C2 and D3. The transmittance measurement was performed in a spectrophotometer. The Variolink II and Rely X U200 resin cements were photoactivated by LED (1400 mW/cm2) for 40 s through the ceramic discs and without the discs (control group). The DC was measured with infrared FTIR spectroscopy, immediately after light activation. Data were analyzed with Kruskall-Wallis and one-way ANOVA, following post-hoc comparisons by Tukey test and Pearson’s correlation test (P<0.05).

Results

LT ceramic exhibited higher transmittance values compared to MO and Z ceramics. LTA2 and LTB2 showed statistically higher transmittance values compared to MOA2, MOA3.5 and ZA3.5. For Variolink II, the ceramic interposition did not influence the DC, since there were no statistical differences between groups with ceramic interposition and the control group. For Rely X U200 cement, the interposition of some ceramics types/shades (LTA3.5, MOA2, MOA3.5 and ZA3.5) significantly decreased the DC values compared to control group. A positive correlation was found between the ceramic transmittance and DC values of both tested cements. Conclusions. The transmittance and DC values of the cements were influenced by composition and shades of the ceramics. The higher the transmittance of ceramics, the higher the DC values for both cements.

Biomaterials: Ceramic and Adhesive Technologies

This review highlights ceramic material options and their use. The newer high-strength ceramics in monolithic form have gained popularity despite the lack of long-term clinical data to support this paradigm shift. Although there are some encouraging clinical data available, there is a need to develop laboratory simulation models that can help predict long-term clinical performance for ceramic and adhesive cements.

Evaluation of the light transmission of chairside polymer infiltrated hybrid ceramics in different shades and thicknesses

BACKGROUND:

This in vitro study aimed to evaluate the amount of polymerizing light passing through hybrid ceramic specimens in different shades and thicknesses.

METHODS:

Rectangular-shaped feldspathic ceramic computer aided design and computer aided manufacturing (CAD-CAM) blocks and translucent and high translucent polymer infiltrated hybrid ceramic CAD-CAM blocks in four different shades (1M1, 1M2, 2M2, and 3M2) were sectioned in four different thicknesses (0.8, 1.5, 2, and 3 mm), and a total of 48 groups ( n = 10) were obtained. Feldspathic ceramic specimens served as the control group. The light transmission of each ceramic specimen was measured three times by using a light-emitting diode and a radiometer. Data were statistically analyzed by using univariate analysis of variance (ANOVA) followed by one-way ANOVA, Tukey honest significant difference, and Tamhane T2 tests (α = 0.05).

RESULTS:

Translucent polymer infiltrated hybrid ceramic specimens exhibited significantly ( p < 0.001) lower light transmission values than high translucent polymer infiltrated hybrid ceramic and feldspathic ceramic specimens, whereas feldspathic ceramic specimens exhibited significantly ( p < 0.001) higher light transmission than translucent and high translucent polymer infiltrated hybrid ceramic specimens. The amount of light transmission significantly ( p < 0.05) decreased when the shade value decreased and the thickness increased.

CONCLUSIONS:

Polymer infiltrated hybrid ceramic specimens showed lower light transmission values than feldspathic ceramic specimens, and the amount of light transmission was affected by the ceramic shade and thickness.

Rely XTM U200 versus Rely XTM ARC: uma comparação da resistência à microtração

Resumo Introdução Os cimentos resinosos são extensivamente utilizados na fixação de restaurações indiretas de cerâmica e cerômero, sendo classificados em duas categorias: os cimentos resinosos convencionais, que não apresentam uma adesão inerente à estrutura dental e requerem o uso de um sistema adesivo e os cimentos resinosos autoadesivos, que não requerem um tratamento adesivo prévio do substrato dentário. Objetivo Avaliar a resistência de união de dois cimentos resinosos, convencional e autoadesivo, quando utilizados na cimentação de restaurações cerâmicas e ceroméricas, trazendo elementos para propiciar melhor compreensão da interação adesiva em procedimentos de cimentação com as referidas categorias de cimentos resinosos. Material e método Dentes humanos (n=20), cedidos pelo banco de dentes da Universidade Federal de Alfenas (UNIFAL), foram preparados para que cilindros de cerâmica ou de cerômero fossem cimentados utilizando-se dois tipos de cimentos resinosos (autoadesivo e convencional). Após a cimentação, 20 palitos foram obtidos e submetidos ao teste de tração, avaliando-se a força necessária para a fratura. Os valores obtidos foram submetidos à análise estatística empregando-se a análise de variância (ANOVA) e o teste de Tukey. Resultado As forças mínimas e máximas necessárias ao rompimento do cimento convencional foram superiores às mesmas requeridas para o rompimento da união promovida pelo cimento autoadesivo, bem como as medianas e as médias aritméticas, independentemente do material restaurador empregado. O teste de Tukey demonstrou que as diferenças entre os cimentos empregados são estatisticamente significantes, independentemente do material restaurador. Conclusão Os resultados deste trabalho sugerem que o material utilizado para a confecção dos corpos de prova (cerâmica ou cerômero) não influenciou na resistência à tração, sendo que o cimento convencional apresentou valores superiores de resistência.

Optical properties and colorimetric evaluation of resin cements formulated with thio-urethane oligomers

OBJECTIVE

The aim of this study was to evaluate the color parameters and optical properties of resin cements (RCs) formulated with thio-urethanes (TUs).

MATERIALS AND METHODS

Six TUs were synthesized by combining thiols (pentaerythritol tetra-3-mercaptopropionate [PETMP] or trimethylol-tris-3-mercaptopropionate [TMP]) with di-functional isocyanates (1,6-Hexanediol-diissocyante [HDDI] [aliphatic-AL] or 1,3-bis(1-isocyanato-1-methylethyl) benzene [BDI] [aromatic-AR] or Dicyclohexylmethane 4,4'-Diisocyanate [HMDI] [cyclic-CC]). TUs (20 wt%) were added to a BisGMA/UDMA/TEGDMA matrix. Filler was introduced at 60 wt%. Fluorescence was evaluated through an UV-light emitting equipment. Coordinates L*, a*, and b* were obtained in the black and white reflectance to evaluate the contrast ratio (CR) and translucency parameter (TP₀₀ ). The coordinates obtained from transmittance were used to evaluate lightness (L*), chroma (C*), color difference (ΔE₀₀ ) after 6 month, and whiteness index for Dentistry (WI_D ).

RESULTS

RCs formulated with TUs presented significantly higher CR, and fluorescence (with T_AR). Significantly lower C*, L*, and TP₀₀ (except for P_AR and T_AL) were also observed in RCs containing TUs. ΔE₀₀ were not significant among the materials. WI_D was not influenced.

CONCLUSION

RCs composed by TU oligomers present higher CR and lower translucency. The material also present higher fluorescence depending on the oligomer used.

CLINICAL SIGNIFICANCE

The use of thio-urethanes to formulate resin cements can ensure a luting material with improved potential to mask colored substrates due to the higher contrast ratio and lower translucency obtained. A final higher fluorescence of restoration is also expected with the use of specific oligomer.

Effect of Post-Space Irrigation with NaOCl And CaOCl at Different Concentrations on the Bond Strength of Posts Cemented with a Self-Adhesive Resin Cement

Abstract The aim of this study was to evaluate the effect of post-space irrigation with NaOCl and CaOCl at different concentrations on the bond strength of posts cemented with a self-adhesive resin cement. Eighty premolars were sectioned 14 mm from the apex, and endodontically treated. The root canal filling was partially removed. Specimens were randomly assigned into 8 groups (n=10), according to the irrigant for post-space irrigation: SS - 0.9% saline solution (control group); CHX - 2% chlorhexidine; 1% NaOCl - 1% sodium hypochlorite; 2.5% NaOCl - 2.5% sodium hypochlorite; 5% NaOCl - 5% sodium hypochlorite; 1% CaOCl - 1% calcium hypochlorite; 2.5% CaOCl - 2.5% calcium hypochlorite; and 5% CaOCl - 5% calcium hypochlorite. For each group, irrigation was performed continuously with 2 ml of solution. The post-spaces were dried with paper points (#80), and glass fiber posts were cemented using a self-adhesive resin cement. The specimens were sectioned perpendicularly and the push-out test was performed. Optical microscopy was used to analyze the failure mode. ANOVA and Bonferroni tests analyzed the bond strength data. NaOCl and CaOCl presented similar bond strength regardless the concentration used to irrigate the post-space (p>0.05). SS showed the highest bond strength (11.47 MPa) (p<0.05). Adhesive failures at the cement/dentin interface were predominant (58.33%). Saline solution should be irrigant of choice to irrigate the post-space before fiber post cementation with self-adhesive resin cement. NaOCl and CaOCl negatively affect the bond strength values.

Dental Cements for Luting and Bonding Restorations: Self-Adhesive Resin Cements

Self-adhesive resin cements combine easy application of conventional luting materials with improved mechanical properties and bonding capability of resin cements. The presence of functional acidic monomers, dual cure setting mechanism, and fillers capable of neutralizing the initial low pH of the cement are essential elements of the material and should be understood when selecting the ideal luting material for each clinical situation. This article addresses the most relevant aspects of self-adhesive resin cements and their potential impact on clinical performance. Although few clinical studies are available to establish solid clinical evidence, the information presented provides clinical guidance in the dynamic environment of material development.

The effect of hydrofluoric acid and resin cement formulation on the bond strength to lithium disilicate ceramic

To investigate how the hydrofluoric acid (HF) concentrations applied to a lithium disilicate glass-ceramic (EMX) affects the surface morphology and microtensile bond strength (μTBS) of ceramics to dentin, using light-cured resin cements with or without UDMA. Sixty-three EMX square ceramic blocks were etched for 20 seconds using different HF concentrations (1%, 5% and 10%) and luted to dentin using two types of resin cement combinations: BisGMA/TEGDMA and BisGMA/TEGDMA/UDMA (n = 10). Each bonded EMX-dentin block was sectioned to obtain 1 mm2 sticks for μTBS evaluation. Half of the sticks were tested after 24 hours and the other half was assessed after 6 months of water storage. Data were statistically assessed using split-plot three-way ANOVA and multiple comparisons were performed using the Tukey's post hoc test (α = 0.05). One EMX sample from each HF concentration was analyzed using field-emission scanning electron microscope (FE-SEM) to characterize the etching pattern. According to the FE-SEM images, increasing the concentration of HF from 1 to 5 and then to 10% led to increased removal of glassy matrix and greater exposure of lithium disilicate crystals. The 10% HF concentration yielded higher μTBS when compared to 1% for BisGMA/TEGDMA formulation (p < 0.05); whereas HF 1% and 5% showed similar μTBS values when compared to 10% HF for BisGMA/TEGDMA/UDMA resin matrix (p > 0.05) at both storage times. Water aging decreased the μTBS values (p < 0.05), except when 10% HF was associated with BisGMA/TEGDMA resin cement. Resin cement formulation and hydrofluoric acid concentrations can interfere with the immediate and long-term glass-ceramic bond strength to dentin.

Effect of Dentin Preparation Mode on the Bond Strength Between Human Dentin and Different Resin Cements

Abstract The aim was to evaluate the influence of different dentin preparation mode in the smear layer characteristics (SL), hybrid layer (HL), and microtensile bond strength (µTBS) to dentin with two resin cements. The occlusal dentin of 120 third molars was exposed. The teeth were divided into 4 groups (n=30) according to the dentin preparation mode: 1- fine grain diamond bur; 2- coarse grain diamond bur; 3- multi laminate carbide steel bur; and, 4- ultrasonic CV Dentus diamond bur. Each treated dentin group was divided into 2 sub-groups (n=15) according to the resin cement: (1) RelyX U200 and (2) RelyX ARC. Resin composite blocks were cemented on dentin. After storage at 37o C for 24 h, beams with a cross section area of 1.0 mm2 were obtained, and tested in a universal testing machine at a crosshead speed of 0.5 mm/min. Two additional teeth for each sub-group were prepared to analyze the SL and HL on a scanning electron microscopy. According to Kruskal-Wallis test and Dunn tests, there was no significant difference in µTBS among the rotary instruments within each resin cement group. RelyX ARC obtained higher µTBS values compared to RelyX U200 (p<0.05). RelyX ARC formed evident HL, which was not observed for RelyX U200. The dentin mode preparation did not influence the µTBS of the resin cements. The SL was different for all instruments. The cementing agent is more determinant in the hybrid layer formation and bond strength to dentin than the instruments applied on dentin.

Influence of light activation of simplified adhesives on the shear bond strength of resin cements to a leucite-reinforced ceramic

Objective

This study aims to evaluate the influence of the light activation of simplified adhesives on the shear bond strength of resin cements to a glass-ceramic. Three factors were evaluated: (1) cement in two levels (light cured and dual cured); (2) adhesive in two levels (Single Bond 2 and Single Bond Universal), and (3) light activation in two levels (yes or no).

Materials and Methods

Thirty-two 1-mm thick slices of a leucite-reinforced glass-ceramic (IPS Empress CAD) were divided into eight groups according to adhesive (Single Bond 2 or Single Bond Universal), cement (AllCem Veneer or AllCem), and light activation of the adhesive before application of the cement (yes or no). Ceramic surfaces were etched for 60 s with 5% hydrofluoric acid, and adhesives were applied. Four cement cylinders were made over each ceramic slice (n = 16) and then submitted to shear bond strength tests.

Statistical Analysis

Data were analyzed with three-way ANOVA and Tukey (α = 0.05).

Results

There were significant differences between adhesives (P < 0.0001) and no differences between cements (P = 0.0763) and light activation (P = 0.4385). No interaction effect occurred (P = 0.05). Single Bond 2 showed higher bond strength than Single Bond Universal.

Conclusions

The light activation of the adhesive before the application of the resin cement did not influence the bond strength.

Resin cements formulated with thio-urethanes can strengthen porcelain and increase bond strength to ceramics

OBJECTIVES

The use of thio-urethane oligomers has been shown to significantly improve the mechanical properties of resin cements (RCs). The aim of this study was to use thio-urethane-modified RC to potentially reinforce the porcelain-RC structure and to improve the bond strength to zirconia and lithium disilicate.

METHODS

Six oligomers were synthesized by combining thiols - pentaerythritol tetra-3-mercaptopropionate (PETMP, P) or trimethylol-tris-3-mercaptopropionate (TMP, T) - with di-functional isocyanates - 1,6-Hexanediol-diissocyante (HDDI) (aliphatic, AL) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (BDI) (aromatic, AR) or Dicyclohexylmethane 4,4'-Diisocyanate (HMDI) (cyclic, CC). Thio-urethanes (20 wt%) were added to a BisGMA/UDMA/TEGDMA organic matrix. Filler was introduced at 60 wt%. The microshear bond strength (μSBS), Weibull modulus (m), and failure pattern of RCs bonded to zirconia (ZR) and lithium disilicate (LD) ceramics was evaluated. Biaxial flexural test and fractographic analysis of porcelain discs bonded to RCs were also performed. The biaxial flexural strength (σ_bf) and m were calculated in the tensile surfaces of porcelain and RC structures (Z = 0 and Z = -t₂, respectively).

RESULTS

The μSBS was improved with RCs formulated with oligomers P_AL or T_AL bonded to LD and P_AL, P_AR or T_CC bonded to zirconia in comparison to controls. Mixed failures predominated in all groups. σ_bf had superior values at Z = 0 with RCs formulated with oligomers P_AL, P_AR, T_AL, or T_CC in comparison to control; σ_bf increased with all RCs composed by thio-urethanes at Z = -t₂. Fractographic analysis revealed all fracture origins at Z = 0.

CONCLUSION

The use of specific thio-urethane oligomers as components of RCs increased both the biaxial flexural strength of the porcelain-RC structure and the μSBS to LD and ZR.

CLINICAL SIGNIFICANCE

The current investigation suggests that it is possible to reinforce the porcelain-RC pair and obtain higher bond strength to LD and ZR with RCs formulated with selected types of thio-urethane oligomers.

Evaluation of long-term bond strength and selected properties of self-adhesive resin cements

This study evaluated the shear bond strength (SBS) of self-adhesive resin cements (SARCs) to dentin and their physical-chemical properties. Five commercial SARCs were evaluated [SmartCem®2 - DENTSPLY (SC2); BisCem® - Bisco (BC); SeT PP® - SDI (SeT); Relyx U100® - 3M ESPE (U100) and YCEM® SA - Yller (YCEM)]. The SARCs were evaluated for SBS to dentin (n = 10) after 24 h, 6 months, and 12 months. The dentin demineralization caused by acidic monomers was observed by SEM, and pH-neutralization of eluate was observed for 24 h. Degree of conversion (DC), rate of polymerization (Rp), flexural strength (FS), and elastic modulus (E) were evaluated. Immediate SBS of SC2, SET, U100, and YCEM were statistically higher than that of BC (p < 0.001). After 12 months, all SARCs showed reduced SBS values and U100 showed values similar to those of SET and YCEM, and higher than those of BC and SC2 (p = 0.001). Demineralization pattern of SARCs was similar. At 24h, all SARCs showed no differences in the pH-value, except BC and U100 (p < 0.001). YCEM showed the highest Rp. U100, YCEM, and SC2 showed statistically higher FS (p<0.001) and E (p < 0.001) when compared with SET and BC. U100 and YCEM showed the best long-term bonding irrespective of the storage period. A significant reduction in SBS was found for all groups after 12 months. SBS was not shown to be correlated with physical-chemical properties, and appeared to be material-dependent. The polymerization profile suggested that an increased time of light activation, longer than that recommended by manufacturers, would be necessary to optimize DC of SARCs.

Effect of different surface treatments and retainer designs on the retention of posterior Pd-Ag porcelain-fused-to-metal resin-bonded fixed partial dentures

The aim of this study was to investigate the adhesive property of palladium-silver alloy (Pd-Ag) and the simulated clinical performance of Pd-Ag porcelain-fused-to-metal (PFM), resin-bonded, fixed partial dentures (RBFPDs). A total of 40 Pd-Ag discs (diameter=5 mm) were prepared and divided into the following four groups (n=10): a) No sandblasting, used as a control; and b, 50 µm; c, 110 µm; and d, 250 µm aluminum oxide (Al₂O₃) particles, respectively. Another 50 discs were pre-sandblasted and divided into five groups (n=10) subjected to different treatments: e) Sandblasting, used as a control; f) silane; g) alloy primer; h) silica coating + silane and i) silica coating + alloy primer. All 90 discs were bonded to enamel with Panavia F 2.0 and then subjected to shear bond strength (SBS) testing. The fracture surfaces were examined by scanning electron microscopy. Next, 40 missing maxillary second premolar models were restored with one of the four following RBFPD designs (n=10): I) A premolar occlusal bar combined with molar double rests (MDR); II) both occlusal bars with a wing (OBB); III) a premolar occlusal bar combined with a molar dental band (MDB); and IV) two single rests adjacent to the edentulous space with a wing (SRB) used as a control. All specimens were aged with thermal cycling and mechanical loading. Subsequently, they were loaded until broken. The data were analyzed by one-way analysis of variance. Al₂O₃ (250 µm) abrasion provided the highest SBS (P<0.05). The alloy primer and silica + silane exhibited increased SBS. Furthermore, fracture analysis revealed that the failure mode varied among the different treatments. Whereas MDB exhibited the highest retention (P<0.05), that of OBB was greater than that of MDR (P<0.05), and the control exhibited the lowest retention. Abrasion with Al₂O₃ (250 µm) effectively increased the adhesive property of Pd-Ag. Additionally, treatment with the alloy primer and silica coating + silane was able to increase the adhesive property of abraded Pd-Ag. Under the present conditions, all three modified retainer types provided improved outcomes for Pd-Ag PFM RBFPDs compared with the control.

Effect of Steam Autoclaving on the Tensile Strength of Resin Cements Used for Bonding Two-Piece Zirconia Abutments

The purpose of this study was to evaluate the effects of steam autoclave sterilization on the tensile strength of two types of resin cements used to bond customized CAD/CAM zirconia abutments onto titanium bases. Forty sets of zirconia abutments cemented to screwed titanium bases of implants analogs were divided into 4 groups (n = 10). Two groups were treated with a conventional chemically activated resin cement (ML, Multilink Ivoclar Vivadent) and the other two groups with a self-adhesive dual resin cement (RelyX U200, 3M ESPE). One group from each cement was submitted to steam autoclaving. The autoclave sterilization cycle was performed after 72 hours of cementation for 15 minutes at 121°C and 2.1 Kgf/cm2. The samples were subjected to tensile strength testing in a universal testing machine (200 Kgf, 0.5 mm/min), from which the means and standard deviations were obtained in Newtons. Results showed (via ANOVA and Tukey's test; α = 0.05) that in the absence of steam autoclaving, no difference was observed in tensile strength between the cements tested: ML: 344.87 (93.79) and U200: 280 (92.42) (P = .314). Steam autoclaving, however, significantly increased tensile strength for the ML: 465.42 (87.87) compared to U200: 289.10 (49.02) (P &lt; .001). Despite the significant increase in the ML samples (P = .013), autoclaving did not affect the tensile strength of the U200 samples (P &gt; 0.05). The authors concluded that steam autoclaving increases the mean tensile strength of the chemically activated cement compared to the dual-cure self-adhesive cement. The performance of both cements evaluated was similar if the sterilization step was disconsidered.

The effect of repeated bonding on the shear bond strength of different resin cements to enamel and dentin

PURPOSE

Cementation failures of restorations are frequently observed in clinical practice. The purpose of this study is to compare the effect of initial and repeated bonding on the bond strengths of different resin cements to enamel and dentin.

MATERIALS AND METHODS

Ninety human maxillary central incisors were bisected longitudinally. The 180 tooth halves were divided into 2 groups (n = 90) for enamel and dentin bonding. The enamel and dentin groups were further divided into 3 groups (n = 30) for different resin cement types. Composite resin (Filtek Ultimate) cylinders (3 × 3 mm) were prepared and luted to enamel and dentin using Variolink II (Group V), RelyX ARC (Group R), or Panavia F 2.0 (Group P) resin cement. After 24 hours, initial shear bond strengths of the resin cements to enamel and dentin were measured. Using new cylinders, the specimens were de-bonded and re-bonded twice to measure the first and the second bond strengths to enamel and dentin. Failure modes and bonding interfaces were examined. Data were statistically analyzed.

RESULTS

Initial and repeated bond strengths to enamel were similar for all the groups. The first (15.3 ± 2.2 MPa) and second (10.4 ± 2.2 MPa) bond strengths to dentin were significantly higher in Group V (P<.0001). Second bond strengths of dentin groups were significantly lower than initial and first bond strengths to dentin (P<.0001).

CONCLUSION

All resin cements have similar initial and repeated bond strengths to enamel. Variolink II has the highest first and second bond strength to dentin. Bond strength to dentin decreases after the first re-bonding for all resin cements.