Adsorption of naphthalene from aqueous solution onto fatty acid modified walnut shells

Comparison of methods for activating sesame stalk lignin biochar for removing benzo[a]pyrene from sesame oil

In this study, three activators and two activation methods were employed to activate sesame lignin-based biochar. The biochar samples were comprehensively characterized, their abilities to adsorb benzo[a]pyrene (BaP) from sesame oil were assessed, and the mechanism was analyzed. The results showed that the biochar obtained by one-step activation was more effective in removing BaP from sesame oil than the biochar produced by two-step activation. Among them, the biochar generated by one-step activation with ZnCl2 as the activator had the largest specific surface area (1068.8776 m3/g), and the richest mesoporous structure (0.7891 m3/g); it removed 90.53 % of BaP from sesame oil. BaP was mainly adsorbed by the mesopores of biochar. Mechanistically, pore-filling, π-π conjugations, hydrogen bonding, and n-π interactions were involved. The adsorption was spontaneous and heat-absorbing. In conclusion, the preparation of sesame lignin biochar using one-step activation with ZnCl2 as the activator was found to be the best for removing BaP from sesame oil. This biochar may be an economical adsorbent for the industrial removal of BaP from sesame oil.

G-C3N4-Ag composite mediated photocatalytic degradation of phenanthrene - A remedy for environmental pollution

In recent years, g-C3N4-Ag nanocomposite synthesis has gained considerable attention for its potential to treat polycyclic aromatic hydrocarbons (PAHs) and to act against bacteria and fungi. In this study, we present a novel approach to the synthesis of g-C3N4-Ag nanocomposite and evaluate its efficiency in both PAH removal and antimicrobial activity. The synthesis process involved the preparation of g-C3N4 by thermal polycondensation of melamine. The factors that affect the adsorption process of PAHs, like time, pH, irradiation type, and adsorbent dosage, were also evaluated. Isotherm models like Langmuir and Freundlich determined the adsorption capability of g-C3N4-Ag. In simulated models, phenanthrene was degraded to a maximum of 85% at lower concentrations of catalyst. The adsorption profile of phenanthrene obeys the pseudo-second-order and Freundlich isotherms pattern. The g-C3N4-Ag nanocomposite also exhibited antimicrobial activity against bacteria (Escherichia coli, Bacillus subtilis, Staphylococcus aureus, Klebsiella pneumoniae) and fungi (Candida albicans). The present study is the first report stating the dual application of g-C3N4-Ag nanocomposite in reducing the concentration of PAH and killing bacterial and fungal pathogens. The higher adsorption capability proclaimed by g-C3N4-Ag nanocomposite shows the fabricated nanomaterial with great potential to remediate organic pollutants from the ecosystem.

One-Step Pyrolysis of Nitrogen-Containing Chemicals and Biochar Derived from Walnut Shells to Absorb Polycyclic Aromatic Hydrocarbons (PAHs)

The pyrolysis of biomass is an efficient means of utilizing biomass resources. Biomass can be converted into various high-performance chemicals and functional materials through pyrolysis. However, current pyrolysis technologies suffer from low conversion rates and single products, so the preparation of nitrogen compounds with high economic value remains a challenge. The walnut shell was soaked in three nitrogen-containing compound solutions before carbonization to produce high-value-added nitrogen-containing chemicals (with a nitrogen content of 59.09%) and biochar for the adsorption of polycyclic aromatic hydrocarbons (PAHs). According to biochar analysis, biochar has a porous structure with a specific surface area of 1161.30 m²/g and a high level of rocky desertification. The surface forms a dense pyrrole structure, and the structure produces π-π interactions with naphthalene molecules, exhibiting excellent naphthalene adsorption with a maximum capacity of 214.98 mg/g. This study provides an efficient, rapid, and environmentally friendly method for producing nitrogen-containing chemicals with high-added value and biochar.

Adsorption of pollutants in wastewater via biosorbents, nanoparticles and magnetic biosorbents: A review

Adsorption has gained much attention as one of the efficient approaches to remediate the contaminants in wastewater. Herein, this critical review focuses on the preparation, modification, application and regeneration of the biosorbents, nanoparticles and magnetic biosorbents for the wastewater treatment in recent 5 years (2017-2021). Among these materials, the development of magnetic biosorbents is attractive owing to their variable active sites, high specific surface area, easy separation and low cost. To improve the adsorption performance of biosorbents, the chemical activations such as acid, alkali and salt activations of biosorbents are discussed. In general, the oxidation reaction in acid, alkali and salt activations increases the porosity of biosorbents. The surface characteristics, surface chemistry of the biosorbents and magnetic biosorbents such as electrostatic interaction, π-π interaction and hydrogen bonding are highlighted. Ionic compounds are separated through ion exchange, surface charge and electrostatic interactions while the organic pollutants are removed via hydrophobicity, π-π interactions and hydrogen bonding. The effect of solution pH, adsorbent dosage, initial concentration of pollutants, adsorption duration and temperature on the adsorption capacity, and removal efficiency are discussed. Generally, an increase in adsorbent dosage resulted in a decrease in adsorption capacity due to the excessive active sites. On the other hand, a higher initial concentration or an increase in contact time of adsorbent increased the driving force, subsequently enhancing the adsorption capacity. Finally, this review will be concluded with a summary, challenges and future outlook of magnetic biosorbents. It is anticipated that this review will provide insights into engineering advanced and suitable materials to achieve cost-effective and scalable adsorbents for practical and sustainable environmental remediation.

A Review on Modification Methods of Adsorbents for Naphthalene in Environment

Naphthalene is one of the most hazardous polycyclic aromatic hydrocarbons to public health. This paper comprehensively summarized the recent development of modification methods of adsorbents for naphthalene removal in the environment. Various modification methods used in the adsorbent were summarized, mainly including acid oxidation modification, salt modification, doping modification, amino modification, microwave modification, and plasma modification. These methods enhance the adsorption performance of naphthalene mainly by changing the pore size and the oxygen content on the surface of the adsorbent. The modification parameters and their effects on naphthalene removal as well as the advantages and disadvantages of each method are described in detail. This review provides the necessary inspiration and guidance for the researchers who develop polycyclic aromatic hydrocarbons adsorption materials in the environment.

Acenaphthene adsorption onto ultrasonic assisted fatty acid mediated porous activated carbon-characterization, isotherm and kinetic studies

Adsorbents originated from biological materials play a vital role in the remediation of diverse toxic pollutants due to their high efficacy, low cost and being environmentally friendly. The present study focusses on the palm shell activated carbon obtained from agricultural waste precursor (palm shell) with the aid of oleic acid activation along with ultrasonic assistance and its effective utilization for acenaphthene adsorption from aqueous and real effluent. The synthesized Ultrasonic assisted palm shell activated carbon (UAC) possessed high surface area of 506.84 m²/g and distinct porous structure as depicted by SEM analysis. The outcomes of zero discharge analyses and acenaphthene adsorption results vouchsafed that, using oleic acid as an effective catalyst, is explicitly advantageous to combine with ultrasonic assistance to fabricate a highly efficient adsorbent for acenaphthene removal from aqueous solution. The UAC obtained at the selected parameters levels, such as temperature of 45 °C and ultrasonic time of 40 min, has the adsorption capacity of 52.745 mg/g. Sips isotherm model computed from the experimental data gave the best fit among the examined isotherm models. To complete the study of adsorption properties of UAC towards acenaphthene, kinetic modeling and thermodynamic aspects of the adsorption process were also scrutinized. The kinetic studies proved that pseudo-second order model is compatible with the experimental data and thermodynamic results revealed that the adsorption process is of endothermic nature. Overall, ultrasonic-assisted preparation of activated carbon from palm shell actuated using Oleic acid was found to be a highly efficient adsorbent which was suitable for acenaphthene removal from aqueous solution.

Magnetic polyamidoamine dendrimer grafted with 4-mercaptobenzoic acid as an adsorbent for preconcentration and sensitive determination of polycyclic aromatic hydrocarbons from environmental water samples

Polyamidoamine dendrimer decorated Fe₃O₄ magnetic nanoparticles was synthesized and grafted with 4-mercaptobenzoic acid (4-MBA). The resulting material was utilized to develop an effective magnetic solid phase extraction method in combination with high performance liquid chromatography for trace determination of polycyclic aromatic hydrocarbons including phenanthrene (PHE), anthracene (ANT), fluoranthene (FLT), pyrene (PYR) and benzo(a)pyrene (BaP). The MNPs@G3.0@4-MBA exhibited to be an efficient extracting medium due to the existence of terminal benzene ring groups, the internal pores, and strong hydrophobic interactions and π-π interactions. The experiments demonstrated that the proposed method possessed excellent linearity in the concentration range of 0.1-300 μg L^-1 with correlation coefficients (R) larger than 0.997, and the limits of detection (LODs, S/N = 3) according to the ratio of signal to noise equal to three of PHE, ANT, FLT, PYR and BaP were 0.014 μg L^-1, 0.032 μg L^-1, 0.055 μg L^-1, 0.027 μg L^-1 and 0.039 μg L^-1, respectively. The proposed method was applied to real water samples and the spiked recoveries were over the range of 92-99%. The results showed that the method earned good repeatability and high sensitivity, and the as-prepared materials were stable and reusable, which displayed that the proposed method would have a wonderful application prospect.

In Situ Modification of Activated Carbons by Oleic Acid under Microwave Heating to Improve Adsorptive Removal of Naphthalene in Aqueous Solutions

This study aimed to improve the adsorption capacity of activated carbon (AC) towards naphthalene (NAP) in aqueous solutions. Starch-based AC (SAC) and pulverized coal-based AC (PCAC) were prepared in a one-pot procedure by activation with oleic acid and KOH under microwave heating. Brunauer–Emmett–Teller (BET) specific surface areas reached 725.0 and 912.9 m2/g for in situ modified SAC (O-SAC1) and PCAC (O-PCAC1), respectively. π–π bond, H-bond, and hydrophobic effects were directly involved in the NAP adsorption process. Batch adsorption data were well fitted by pseudo-second order kinetics and the Freundlich isotherm model. As compared to ACs prepared with only KOH activation, NAP adsorption capacities of PCAC and SAC prepared by the one-pot method increased by 16.9% and 13.7%, respectively. Influences of varying factors were investigated in column adsorption of NAP using O-SAC1 and O-PCAC1. Based on breakthrough curves analysis, the larger column height (H), lower flow rate (Q0), and lower initial concentration (C0) resulted in the longer breakthrough and exhaustion times in both cases. Specifically, we concluded that O-PCAC1 exhibits better adsorption capacity than O-SAC1 in the given conditions. The optimized operating parameters were 1 cm (H), 1 mL/min (Q0) and 30 mg/L (C0). Finally, column adsorption data could be well fitted by the Thomas model.

Ionic Cross-Linking Fabrication of Chitosan-Based Beads Modified with FeO and TiO2 Nanoparticles: Adsorption Mechanism toward Naphthalene Removal in Seawater from Cartagena Bay Area

Polycyclic aromatic hydrocarbons (PAHs) are complex molecules produced by the thermal decomposition of organic matter in anthropogenic activities. Novel composites with enhanced physicochemical properties aim to overcome limitations such as adsorption capacity, affinity, and stability for PAHs adsorption. Composites based on chitosan are promising due to the good biocompatibility and adsorption properties. This study focuses on the facile preparation of chitosan beads modified with iron oxide (FeO) and titanium dioxide (TiO₂) nanoparticles via ionic cross-linking (Ch-FeO/TiO₂). FeO and TiO₂ were synthesized performing co-precipitation and green chemistry methods, respectively. The characterization evidenced the formation of Ch-FeO/TiO₂ with good crystallinity, excellent thermal stability, and superparamagnetic response, attributed to the presence of FeO and TiO₂ nanoparticles. High thermal stability up to 270 °C was related to the cross-linked chitosan network. The enhanced adsorption mechanism of Ch-FeO/TiO₂ was determined by removing naphthalene from water and seawater samples. The Ch-FeO/TiO₂ showed a higher adsorption capacity of 33.1 mg/g compared to 29.8 mg/g of the unmodified chitosan (un-Ch) beads. This is due to the higher functional surface area of 27.13 m²/g, compared to that of 0.708 m²/g for un-Ch. We found a rapid adsorption rate of 240 min and the maximum adsorption capacity of 149.3 mg/g for Ch-FeO/TiO₂. A large number of actives sites allows for increasing the naphthalene molecules interaction. Adsorption in seawater samples from Cartagena Bay (Colombia) exhibits an outstanding efficiency of up to 90%. These results suggest a promising, cheap, and environmentally friendly composite for remediation of water sources contaminated with complex compounds.

Synthesis of Cost-Effective Pomelo Peel Dimethoxydiphenylsilane-Derived Materials for Pyrene Adsorption: From Surface Properties to Adsorption Mechanisms

This study investigated the adsorption behaviors of pyrene (PYR) on a pomelo peel adsorbent (PPA), biochar (PPB), and H₃PO₄-modified (HPP), NaOH-activated (NPP), and dimethoxydiphenylsilane-treated (DPDMS-NPP) pomelo peel materials. SEM, FTIR, and elemental analyses of DPDMS-NPP's surface structure showed that the material was characterized by a well-developed porous structure, a large specific surface area (698.52 m² g^-1), and an abundance of phenyl functional groups. These properties enhance the PYR adsorption performance of DPDMS-NPP. Experimental results indicated that the adsorption capacity of DPDMS-NPP was significantly affected by the amount of material used and the initial concentration of PYR. Kinetic assessments suggested that PYR adsorption on PPA, NPP, and DPDMS-NPP could be accurately described by the pseudo second-order model. The adsorption process was controlled by several mechanisms, including electron donor-acceptor (EDA), electrostatic, and π-π interactions as well as film and intraparticle diffusion. The adsorption isotherm studies showed that PYR adsorption on DPDMS-NPP and PPA was well described by the Langmuir model and the maximum Langmuir adsorption capacity of DPDMS-NPP was 531.9 μg g^-1. Overall, the results presented herein suggested that the use of DPDMS-NPP adsorbents constitutes an economic and environmentally friendly approach for the mitigation of PYR contamination risks.

Assessment of schwertmannite, jarosite and goethite as adsorbents for efficient adsorption of phenanthrene in water and the regeneration of spent adsorbents by heterogeneous fenton-like reaction

Schwertmannite, jarosite or goethite are commonly used to remove metals and/or metalloids from contaminated water via adsorption processes, but it is still unclear whether they can be used as adsorbents to remove hydrophobic organic pollutants (HOCs), such as polycyclic aromatic hydrocarbons (PAHs), from groundwater or wastewater. Here, the feasibility of using these iron (oxyhydr) oxide minerals as adsorbents for phenanthrene (a model PAH) adsorption and regenerating the spent adsorbents via heterogeneous Fenton-like reaction was investigated. Results showed that they exhibited rapid adsorption rates and considerable adsorption capacities for phenanthrene. The maximum Langmuir capacities (Qmax) for phenanthrene adsorption at 28 °C were in an ascending order of goethite (567 μg·g-1) < schwertmannite (727 μg·g-1) < jarosite (2088 μg·g-1). The adsorption process was a spontaneous and exothermic process along with the decrease of randomness at the solid/liquid interfaces, which was influenced by temperature, adsorbent dosage, and the coexistence of inorganic anions. Both schwertmannite and jarosite were superior to goethite in light of their easy separation from the bulk solution after the adsorption processes. A multi-cycle experiment demonstrated that the regeneration efficiency of schwertmannite (97.9-99.7%) was much higher than that of jarosite (80.1-87.2%), and the mineral structure, morphology and functional groups of schwertmannite were not changed during the successive adsorption-regeneration processes. Therefore, among the investigated three iron (oxyhydr) oxide minerals, schwertmannite was an attractive and regenerable adsorbent for the removal of phenanthrene from water owing to its high adsorption capacity, good separation ability, and excellent reusability.

Removal of methylene blue dye from aqueous solutions by adsorption on levulinic acid-modified natural shells

This study has developed an innovative and environmentally friendly approach for the removal of methylene blue (MB) dye by natural shells (NShs) chemically modified with levulinic acid (LA). Almond shell (ASh), walnut shell (WSh), and apricot kernel shell (AKSh) were used as waste fillers. The adsorption behavior of MB onto the biosorbents was investigated with respect to parameters such as sorbent dosage (0.4-6 g/L), pH (3-10), initial dye concentration (10-500 mg/L), and temperature (25-65 °C). The biosorbents were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) analysis. The isotherm and kinetic adsorption data can be said to fit the Freundlich isotherm model and the pseudosecond-order model, respectively. The maximum adsorption capacity (q_max) of LA-modified walnut shell (LA-WSh), almond shell (LA-ASh), and apricot kernel shell (LA-AKSh) calculated by the Langmuir equation at 25 °C was 294.1, 270.2, and 180.0 mg/g, respectively. The results of thermodynamic analysis showed that adsorption was feasible, endothermic, and spontaneous.

Recent advances in the use of walnut (Juglans regia L.) shell as a valuable plant-based bio-sorbent for the removal of hazardous materials

The effective use of agricultural by-products is definitely a major challenge in waste management. In the walnut fruit processing industry, large amounts of shells are produced as agricultural by-products and discarded or burned produced as fuel. Walnut (Juglans regia L.) is a valuable tree nut in the Juglandaceae family. The fruit is composed of four main parts: the kernel, the skin, the shell, and the husk. The importance of walnuts is mostly related to theirs valuable kernels. However, their shells are currently experiencing as much interest as their kernels due to the beneficial effects of the shells. In the past several years, walnut shell (WS) has been widely explored as a naturally inert plant-based biosorbent. In this review, we first highlight recent scientific literature regarding the development of adsorbents from WS in the form of carbon-based materials including unmodified/modified WS, and activated carbons (ACs). Next, we discuss the potential applications of WS-derived by-products as natural yet effective adsorbents for the removal of various hazardous materials including heavy metals (HMs), synthetic industrial dyes, and harmful chemicals.

Competitive adsorption of naphthalene and phenanthrene on walnut shell based activated carbon and the verification via theoretical calculation

Walnut shell based activated carbon (WAC) was prepared via microwave-assisted KOH activation.

Adsorption of lead ion from aqueous solution by modified walnut shell: kinetics and thermodynamics

The novel modified walnut shell (WNS-MAH) with higher adsorption capacity for lead ion was prepared by reacting walnut shell (WNS) with maleic anhydride. Both WNS and WNS-MAH were analyzed by SEM and FTIR. The adsorption capacity of WNS-MAH for lead ion was evaluated at different adsorbent doses, pHs, time and temperatures. The adsorption kinetics and adsorption isotherms were investigated from (298 to 318) K. The adsorption kinetics of lead ion onto WNS-MAH were fitted using pseudo-first-order, pseudo-second-order and Elovich models. It was found that pseudo-second-order model gives the best correlation results. The diffusion mechanism was determined according to the intraparticle diffusion equation and Boyd equation. Results suggested the adsorption process was governed by film diffusion. The equilibrium adsorption data were fitted with the Freundlich model and the Langmuir model. The maximum adsorption capacity of WNS-MAH for lead ion removal was 221.24 mg/g at 318 K. The equilibrium adsorption data were analyzed using the D-R model, and the feature concentration ( Ce' ) was determined to distinguish chemisorption and physisorption. The thermodynamic parameters (ΔG, ΔH and ΔS) were calculated. Additionally, the regeneration property was studied and the adsorption process was confirmed by energy disperse spectroscopy.

Hydrothermal synthesis and microwave-assisted activation of starch-derived carbons as an effective adsorbent for naphthalene removal

In this work, starch-derived spherical carbon (HC) was prepared by hydrothermal carbonization and further activated with microwave assistance to obtain the target activated carbon (HMAC). The samples were characterized by methods of N2 adsorption-desorption, Brunauer-Emmett-Teller analysis, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, elemental analysis and scanning electron microscopy. Moreover, HMAC has a high BET surface area of 616.8 m2 g-1. The effects of initial naphthalene concentration, contact time, temperature, and pH of the naphthalene adsorbed on HC and HMAC were investigated systematically. The HMAC exhibits higher capability for naphthalene removal than HC, and the equilibrium adsorption quantity of HMAC was 223.03 mg g-1 at 303 K. The kinetic data revealed that the equilibrium time for naphthalene adsorption on samples was achieved at 40 min. The adsorption process of HC and HMAC for naphthalene both followed the pseudo-second-order kinetic and Freundlich isotherm models. Additionally, H-bond and π-π interactions were proposed to be involved in the adsorption process. An increasing adsorption amount of naphthalene onto HC and HMAC was observed when the pH value varied from 2 to 10. The HMAC can be successfully regenerated and maintained sorption performance after three cycles. This study revealed that HMAC obtained by hydrothermal synthesis combined with microwave-assisted activation has a promising application in the field of naphthalene removal.

The combination of novel airlift magnetic separation loop system and an efficient biosorbent for the removal of Pb(II) from aqueous solution

An efficient biosorbent containing magnetic nanoparticles, walnut shell powder, foam, and alginate (AMWSF) was prepared and used in Pb(II) removal. The adsorption process was performed in an airlift magnetic separation loop system. Optimum adsorption conditions were tested at pH 3-7, biomass dose of 0.03-0.4 g, temperature of 15-35 °C, initial Pb(II) ion concentration of 50-400 mg·L^-1, and contact time of 10-480 min. The equilibrium adsorption capacity reached up to 69.45 mg·g^-1. The physicochemical properties of AMWSF were analyzed by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy. The experimental data were in agreement with the pseudo-second-order kinetic and Langmuir isotherm models. The influences of Cu(II), Cd(II), and Zn(II) on Pb(II) adsorption showed antagonistic effect strength in the order of Cu(II) > Cd(II) > Zn(II). AMWSF was reused seven times and separated rapidly by magnetic field. The results demonstrated the potential of AMWSF in practical applications involving Pb(II).

Walnut (Juglans regia L.) shell pyroligneous acid: chemical constituents and functional applications

Upon the processing of different agricultural products, considerable amounts of by-products and bio-wastes are produced and discarded or burnt as fuel, which are a potential source of valuable compounds. Over the past several decades, plant by-products have been recognized as a source of nutraceutical components, including dietary fibers, phenolics, and many other useful compounds. The walnut is known as an important tree nut. The shell of a walnut is the middle part of the fruit and it is a waste product of walnut processing industries. Recently, pyroligneous acids from the walnut shell have been receiving much-increasing interest because of their excellent antimicrobial and antioxidant activities. Hence, this review deals with the recent scientific literature on walnut shell pyroligneous acids and their chemical composition as well as their functional applications.

High removal performance of dissolved oil from aqueous solution by sorption using fatty acid esterified pineapple leaves as novel sorbents

Esterification of the lignocellulosic biomass (pineapple leaves) by long chain fatty acids for oil sorption.