Ozonation of the UV filter benzophenone-4 in aquatic environments: Intermediates and pathways

Degradation kinetics and disinfection by-products formation of benzophenone-4 during UV/persulfate process

The degradation kinetics, reaction pathways, and disinfection by-products formation of an organic UV filter, benzophenone-4 (BP4) during UV/persulfate oxidation were investigated. BP4 can hardly be degraded by UV alone, but can be effectively decomposed by UV/persulfate following pseudo-first order kinetics. BP4 degradation rate was enhanced with increasing persulfate dosage and decreasing pH from 8 to 5. However, the degradation rate of BP4 at pH 9 was higher than that at pH 8 because of the presence of phenolic group in BP4 structure. and SO 4 - ⋅ were confirmed as the major contributors to BP4 decomposition in radical scavenging experiments, and the second-order rate constants between HO ⋅ and BP4 as well as those between SO 4 - ⋅ and BP4 were estimated by establishing and solving a kinetic model. The presence of B r - and humic acid inhibited the decomposition of BP4, while N O 3 - promoted it. The mineralisation of BP4 was only 9.1% at the persulfate concentration of 50 μM. Six degradation intermediates were identified for the promulgation of the reaction pathways of BP4 during UV/persulfate oxidation were proposed as a result. In addition, the formation of DBP in the sequential chlorination was evaluated at different persulfate dosages, pH values, and water matrix. The results of this study can provide essential knowledge for the effective control of DBP formation with reducing potential hazard to provide safe drinking water to the public.

The environmental sources of benzophenones: Distribution, pretreatment, analysis and removal techniques

Benzophenones (BPs) have wide practical applications in real human life due to its presence in personal care products, UV-filters, drugs, food packaging bags, etc. It enters the wastewater by daily routine activities such as showering, impacting the whole aquatic system, then posing a threat to human health. Due to this fact, the monitoring and removal of BPs in the environment is quite important. In the past decade, various novel analytical and removal techniques have been developed for the determination of BPs in environmental samples including wastewater, municipal landfill leachate, sewage sludge, and aquatic plants. This review provides a critical summary and comparison of the available cutting-edge pretreatment, determination and removal techniques of BPs in environment. It also focuses on novel materials and techniques in keeping with the concept of "green chemistry", and describes on challenges associated with the analysis of BPs, removal technologies, suggesting future development strategies.

Degradation of the UV Filter Benzophenone-4 by Ferrate (VI) in Aquatic Environments

This work demonstrates the potential utility of ferrate(VI)-based advanced oxidation processes for the degradation of a representative UV filter, BP-4. The operational parameters of oxidant dose and temperature were determined with kinetic experiments. In addition, the effects of water constituents including anions (Cl−, HCO3−, NO3−, SO42−), cations (Na+, K+, Ca2+, Mg2+, Cu2+, Fe3+), and humic acid (HA) were investigated. Results suggested that the removal rate of BP-4 (5 mg/L) could reach 95% in 60 min, when [Fe(VI)]:[BP-4] = 100:1, T = 25 °C and pH = 7.0, The presence of K+, Cu2+ and Fe3+ could promote the removal of BP-4, but Cl−, SO42−, NO3−, HA and Na+ could significantly inhibit the removal of BP-4. Furthermore, this Fe(VI) oxidation processes has good feasibility in real water samples. These results may provide useful information for the environmental elimination of benzophenone-type UV filters by Fe(VI).

Structure-related endocrine-disrupting potential of environmental transformation products of benzophenone-type UV filters: A review

Benzophenone-type UV filters (BPs) represent a very diverse group of chemicals that are used across a range of industrial sectors around the world. They are found within different environmental compartments (e.g. surface water, groundwater, wastewater, sediments and biota) at concentrations ranging from ng/L to mg/L. Some are known as endocrine disruptors and are currently within the scope of international regulations. A structural alert for high potential of endocrine disrupting activity was assigned to 11 BP derivatives. Due to the widespread use, distribution and disruptive effects of some BPs, knowledge of their elimination pathways is required. This review demonstrates that biodegradation and photolytic decomposition are the major elimination processes for BP-type UV filters in the environment. Under aerobic conditions, transformation pathways have only been reported for BP, BP-3 and BP-4, which are also the most common derivatives. Primary biodegradation mainly results in the formation of hydroxylated BPs, which exhibit a structure-related increase in endocrine activity when compared to their parent substances. By combining 76 literature-based transformation products (TPs) with in silico results relating to their receptor activity, it is demonstrated that 32 TPs may retain activity and that further knowledge of the degradation of BPs in the environment is needed.

Sulphate radical oxidation of benzophenone: kinetics, mechanisms and influence of water matrix anions

Benzophenone (BP) is an emerging contaminant that is widely distributed in soil, groundwater, sediment and surface water. In this study, the degradation kinetics, mechanisms, and influence of anions on thermally activated persulphate (TAP) oxidation of BP were systematically investigated. BP degradation was promoted by elevated temperature. The BP degradation data fitted well to the Arrhenius equation with calculated activation energy of 122.8 kJ/mol. BP degradation was also promoted by alkaline pH and high persulphate concentrations. Radical scavenging experiments suggested that both SO₄^•- and HO^• were involved in BP oxidation. Ultra-high-performance liquid chromatography coupled to Orbitrap mass spectrometry (UHPLC-Orbitrap-MS) identified six degradation intermediates. Based on these results, two possible reaction pathways were proposed. Water matrix anions had complex impacts on BP degradation by TAP. Cl^- had dual effects on the reaction: low concentration promoted it while high concentration inhibited it. Br^- strongly suppressed the reaction. SO₄^2- and NO₃^- did not affect the reaction. Overall, this study shows that thermally activated persulphate can effectively remove BP and water matrix anions greatly influence the reaction.

N-Doped Biochar as a New Metal-Free Activator of Peroxymonosulfate for Singlet Oxygen-Dominated Catalytic Degradation of Acid Orange 7

In this paper, using rice straw as a raw material and urea as a nitrogen precursor, a composite catalyst (a nitrogen-doped rice straw biochar at the pyrolysis temperature of 800 °C, recorded as NRSBC800) was synthesized by one-step pyrolysis. NRSBC800 was then characterized using XPS, BET, TEM and other technologies, and its catalytic performance as an activator for permonosulfate (PMS) to degrade acid orange 7 (AO7) was studied. The results show that the introduction of N-doping significantly improved the catalytic performance of NRSBC800. The NRSBC800/PMS oxidation system could fully degrade AO7 within 30 min, with the reaction rate constant (2.1 × 10 ^-1 min^-1) being 38 times that of RSBC800 (5.5 × 10^-3 min^-1). Moreover, NRSBC800 not only had better catalytic performance than traditional metal oxides (Co₃O₄ and Fe₃O₄) and carbon nanomaterial (CNT) but also received less impact from environmental water factors (such as anions and humic acids) during the catalytic degradation process. In addition, a quenching test and electron paramagnetic resonance (EPR) research both indicated that AO7 degradation relied mainly on non-free radical oxidation (primarily singlet oxygen (¹O₂)). A recycling experiment further demonstrated NRSBC800's high stability after recycling three times.

Fabrication of Cementitious Microfiltration Membrane and Its Catalytic Ozonation for the Removal of Small Molecule Organic Pollutants

In this study, a low-cost cementitious microfiltration membrane (CM) with a catalytic ozone oxidation function for the removal of organic pollutants was fabricated by using cementitious and C-10 μm silica powders at a certain silica–cementitious particle ratio (s/c). The effect of the s/c on the pore size distribution and mechanical strength of the membrane was investigated. The membrane pore size showed a bimodal distribution, and the higher the s/c, the closer the second peak was to the accumulated average particle size of silica. The increase in the s/c led to a decrease in the bending strength of the membrane. The cross-sectional morphology by SEM and crystal structure by XRD of CMs confirmed that a calcium silicate hydrate gel was generated around the silica powder to improve the mechanical strength of the CM. Considering the bending strength and pore size distribution of CMs, s/c = 0.5 was selected as the optimal membrane fabrication condition. The FT-IR results characterizing the surface functional groups of CMs were rich in surface hydroxyl groups with the ability to catalyze ozone oxidation for organic pollutant removal. Six small molecule organic pollutants were selected as model compounds for the efficiency experiments via a CM–ozone coupling process to prove the catalytic property of the CM. The CM has an alkaline buffering effect and can stabilize the initial pH of the solution in the catalytic ozonation process. The reuse experiments of the CM–ozone coupling process demonstrated the broad spectrum of the CM catalytic performance and self-cleaning properties. The results of this study provide the basis and experimental support to expand the practical application of CMs.

Ozone Degradation of Prometryn in Ruditapes philippinarum: Response Surface Methodology Optimization and Toxicity Assessment

ABSTRACT

This study optimized the method for ozone (O3) degradation of prometryn in the clam Ruditapes philippinarum and evaluated toxicity changes during ozone degradation. The gas chromatography method for the detection of prometryn was appropriately improved. The linear range was 5 to 500 ng/mL, with a correlation coefficient of 0.9964. The addition concentration of prometryn was 0.025 to 0.100 mg/kg, the recovery was 77.97 to 85.00%, the relative standard deviation (n = 6) was 2.36 to 7.86%, and the limit of detection was 0.3 μg/kg. Using the central composite design in two experiments, ozone as gas and ozone dissolved in water, the effect of degradation rate was studied on three variables: ozone concentration, temperature, and exposure time. Ozone as gas and ozone dissolved in water have the same degradation effect on prometryn. The O3 concentration was 4.2 mg/L, the temperature was 40°C, the exposure time was 10 min, and the maximum degradation rate was 89.94 and 89.69% for the two experiments, respectively. In addition, the toxicity of ozone degradation products was evaluated using buffalo rat liver cells. After ozone treatment for 30 min, the toxicity of the ozone degradation products was reduced to 52.15% compared with that of prometryn itself. The toxicity of the ozone degradation products increased slightly when the ozonation time was prolonged; the toxicity at 180 min was greater than that of the parent compound prometryn. Overall, the application of ozone degradation of pesticide residues is a promising new technology. This study determined better degradation conditions for prometryn in R. philippinarum and also provided a theoretical basis for the widespread use of ozone technology in the future.

HIGHLIGHTS

Degradation of prometryn in Ruditapes philippinarum using ozonation: Influencing factors, degradation mechanism, pathway and toxicity assessment

In recent years, prometryn was utilized as watergrass remover in the aquaculture industry, resulting in the accumulated residual in the aquatic products. The present study focuses on the ozone degradation of prometryn in the Ruditapes philippinarum. The ozone concentration in water increased along with the injection time (60min). The contents of hydroxyl (·OH) and superoxide (O2·^-) radicals increased along with the ozone injection time. The effects of temperature, pH, prometryn initial concentration and ozone concentration on the removal efficiency of prometryn were evaluated. The maximum removal efficiency of 86.12% was obtained under the conditions of pH 7, prometryn initial concentration 0.05 mg/kg and the ozone concentration 4.2 mg/L at 28 °C for 30 min. Ion chromatography (IC) and Fourier transform infrared (FT-IR) spectroscopy results show that the S and N atoms in the outer layer of the triazine ring during the prometryn degradation process were oxidized and removed. A total of 30 intermediate compounds were identified using the gas chromatography-mass spectrometry (GC-MS) method. Combined with the IC and FT-IR results, three possible degradation pathways of prometryn were proposed. The prometryn was finally degraded into some small molecules with reduced toxicity by 63.16% for 120 min ozonization treatment. Overall, our work provides a novel approach for prometryn degradation in Ruditapes philippinarum, which can be extended for removing the residues of agricultural and veterinary drugs in other aquatic products.

Novel CuCo2O4 Composite Spinel with a Meso-Macroporous Nanosheet Structure for Sulfate Radical Formation and Benzophenone-4 Degradation: Interface Reaction, Degradation Pathway, and DFT Calculation

A series of CuCo₂O₄ composite spinels with an interconnected meso-macroporous nanosheet morphology were synthesized using the hydrothermal method and subsequent calcination treatment to activate peroxymonosulfate (PMS) for benzophenone-4 (BP-4) degradation. As-prepared CuCo₂O₄ composite spinels, especially CuCo-H3 prepared by adding cetyltrimethylammonium bromide, showed superior reactivity for PMS activation. In a typical reaction, BP-4 (10.0 mg/L) was almost completely degraded in 15 min by the activation of PMS (200.0 mg/L) using CuCo-H3 (100.0 mg/L), with only 9.2 μg/L cobalt leaching detected. Even after being used six times, the performance was not influenced by the lower leaching of ions and surface-absorbed intermediates. The possible interface mechanism of PMS activation by CuCo-H3 was proposed, wherein a unique interconnected meso-macroporous nanosheet structure, strong interactions between copper and cobalt, and cycling of Co(II)/Co(III) and Cu(I)/Cu(II) effectively facilitated PMS activation to generate SO₄^•- and ^•OH, which contributed to BP-4 degradation. Furthermore, combined with intermediates detected by liquid chromatography quadrupole time-of-flight mass spectrometry and density functional theory calculation results, the degradation pathway of BP-4 involving hydroxylation and C-C bond cleavage was proposed.

Elimination efficiency of organic UV filters during ozonation and UV/H2O2 treatment of drinking water and wastewater effluent

The efficiency of elimination of organic UV filters by ozonation and UV_254nm/H₂O₂ processes was assessed and predicted in simulated treatments of sewage-impaired drinking water and wastewater effluent in bench-scale experiments. Second-order rate constants (k) for the reactions of the eight UV filters with ozone and OH were determined by quantum chemical calculations and competition kinetics methods, respectively. The UV filters containing phenolic (ethylhexyl-salicylate, homosalate, and benzophenone-3) and olefinic moieties (4-methylbenzylidene-camphor, benzyl-cinnamate, and 2-ethylhexyl-4-methoxycinnamate) showed high ozone reactivity (k ≥ 8 × 10⁴ M^-1s^-1 at pH 7), while those without such electron-rich moieties (isoamyl-benzoate and benzophenone) were ozone-refractory. All the UV filters showed high OH reactivity (k ≥ 6.2 × 10⁹ M^-1s^-1). In concordance with the rate constant information, the phenolic and olefinic UV filters were efficiently eliminated by ozone treatment, requiring specific ozone doses of <0.5 mgO₃/mgDOC for ∼100% elimination. The UV filters were eliminated by ≤ 38% at a UV fluence of 1500 mJ/cm² in the UV_254nm-only treatment. Rapid photoisomerisation between the E and Z geometric isomers was observed for the olefinic UV filter, benzyl-cinnamate. The addition of H₂O₂ (10 mg/L) greatly enhanced the elimination of all UV filters, indicating that OH was the main contributor to their elimination in the UV_254nm/H₂O₂ treatment. A chemical kinetics approach developed previously for ozonation and UV/H₂O₂ processes was shown to predict the elimination of the UV filters in the tested water matrices reasonably well, demonstrating that the chemical kinetics method can be used for a priori prediction of micropollutant elimination in oxidative treatment processes for potable reuse of municipal wastewater effluents.

Degradation of UV Filter Ethyl 4-Aminobenzoate (Et-PABA) Using a UV-Activated Persulfate Oxidation Process

In this paper, the ultraviolet/persulfate (UV/PDS) combined oxidation process was used to remove the ethyl 4-aminobenzoate (Et-PABA), one of the typical 4-aminobenzoic acid (PABA)-type UV filters. The effects of various factors on the removal of Et-PABA using the UV/PDS process were investigated, and the degradation mechanisms of Et-PABA were explored. The results showed that the UV/PDS process can effectively remove 98.7% of Et-PABA within 30 min under the conditions: UV intensity of 0.92 mW·cm−2, an initial concentration of Et-PABA of 0.05 mM, and a PDS concentration of 2 mM. The removal rate of Et-PABA increased with the increase in PDS dosage within the experimental range, whereas humic acid (HA) had an inhibitory effect on Et-PABA removal. Six intermediates were identified based on HPLC–MS and degradation pathways were then proposed. It can be foreseen that the UV/PDS oxidation process has broad application prospects in water treatment.

CoMn2O4 Catalyst Prepared Using the Sol-Gel Method for the Activation of Peroxymonosulfate and Degradation of UV Filter 2-Phenylbenzimidazole-5-sulfonic Acid (PBSA)

In this study, a bimetallic oxide catalyst of cobalt-manganese (CoMn2O4) was synthesized using the sol-gel method, and it was then characterized using a variety of techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) spectroscopy, X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption-desorption isotherms. The obtained novel catalyst, i.e., CoMn2O4, was then used as an activator of peroxymonosulfate (PMS) for the catalytic degradation of a commonly-used UV filter, 2-phenylbenzimidazole-5-sulfonic acid (PBSA) in water. The effects of various factors (e.g., catalyst dosage, PMS concentration, reaction temperature, and pH) in the process were also evaluated. Chemical scavengers and electron paramagnetic resonance (EPR) tests showed that the •OH and SO4•- were the main reactive oxygen species. Furthermore, this study showed that CoMn2O4 is a promising catalyst for activating PMS to degrade the UV filters.

Ozonation of pentabromophenol in aqueous basic medium: Kinetics, pathways, mechanism, dimerization and toxicity assessment

Ozonation has been identified effective technique to degrade phenolic compounds, and production of intermediate dimers are major threat. In this study, we systematically investigated the degradation of Pentabromophenol (PBP) in an aqueous medium by using two different ozone generators (sources: air and water). We studied various factors that influenced the degradation kinetics of PBP, including the pH (7.0, 8.0, and 9.0), humic acid (HA) and anions (Cl^-, SO₄^2-, NO₃^-, and HCO₃^-). PBP was efficiently degraded within 5 min (O₃ source: water) and 45 min (O₃ source: air) at pH 8.0 maintained by phosphate buffer. Reaction kinetics revealed 17 b y-products with five possible pathways, including dimers with their isomers and lower bromophenols. Furthermore, the frontier molecular orbital theory was employed to confirm the proposed ozonation pathways, including the breakage of the CO bond at C₅ and C₄ positions, and the cleavage of the CC bond at C₃ and C₆ position. Product P5, P14 (hydroxyl-nonabromophenyl ether) and P15 (dihydroxyl-octabromophenyl ether) were identified with isomers. Ecological Structure Activity Relationships toxicity assessment resulted into the conversion of highly toxic PBP (acute toxicity: LC₅₀ = 0.11 mg L^-1 for fish, LC₅₀ = 0.124 mg L^-1 for daphnia, and EC₅₀ = 0.118 mg L^-1 for green algae) to less harmful products aside from dimers. P14 (acute toxicity: LC₅₀ = 1.04 × 10⁵) found to be more toxic as compare to PBP. From these findings, we concluded that ozonation is an effective and ideal process for PBP degradation.

Insight into the Degradation of Two Benzophenone-Type UV Filters by the UV/H2O2 Advanced Oxidation Process

Environmental problems caused by UV filters, a group of emerging contaminants, have attracted much attention. The removal of two typical UV filters benzophenone (BP) and 4,4′-dihydroxy-benzophenone (HBP) in water was investigated by the UV/H2O2 process. The response surface methodology (RSM) and central composite design (CCD) were applied to investigate the effects of the process parameters on the degradation rate constants, including the initial contaminant concentration, H2O2 dose, and UV light intensity. BP is more easily degraded by the UV/H2O2 process. Both processes followed pseudo-first-order kinetics. The results obtained with the built RSM model are in accordance with the experimental results (adjusted coefficients R2(adj)= 0.9835 and 0.9778 for BP and HBP, respectively). For both processes, the initial contaminant concentration (exerting a negative effect) were the most important factors controlling the degradation, followed by H2O2 dose and UV intensity (exerting positive effects). A total of 15 BP degradation products and 13 HBP degradation products during the UV/H2O2 process were identified by LC/MS and GC/MS. A series of OH radical irritated reactions, including hydroxylation, carboxylation, and ring cleavage, led to the final degradation of BP and HBP. Degradation pathways of BP and HBP were also proposed. On the whole, this work is a unique contribution to the systematic elucidation of BP and HBP degradation by the UV/H2O2 process.

Suspect Screening and Regulatory Databases: A Powerful Combination To Identify Emerging Micropollutants

This study demonstrates that regulatory databases combined with the latest advances in high resolution mass spectrometry (HRMS) can be efficiently used to prioritize and identify new, potentially hazardous pollutants being discharged into the aquatic environment. Of the approximately 23000 chemicals registered in the database of the National Swedish Product Register, 160 potential organic micropollutants were prioritized through quantitative knowledge of market availability, quantity used, extent of use on the market, and predicted compartment-specific environmental exposure during usage. Advanced liquid chromatography (LC)-HRMS-based suspect screening strategies were used to search for the selected compounds in 24 h composite samples collected from the effluent of three major wastewater treatment plants (WWTPs) in Sweden. In total, 36 tentative identifications were successfully achieved, mostly for substances not previously considered by environmental scientists. Of these substances, 23 were further confirmed with reference standards, showing the efficiency of combining a systematic prioritization strategy based on a regulatory database and a suspect-screening approach. These findings show that close collaboration between scientists and regulatory authorities is a promising way forward for enhancing identification rates of emerging pollutants and expanding knowledge on the occurrence of potentially hazardous substances in the environment.

Benzophenone-4 Promotes the Growth of a Pseudomonas sp. and Biogenic Oxidation of Mn(II)

Interactions between microbes and micropollutants (MPs) play a crucial role in water purification or treatment. Current studies have generally focused on the direct degradation or cometabolism of MPs. Considering the increasing interest in and importance of the roles of MPs in microbial metabolism, we adopted an Mn(II)-oxidizing Pseudomonas sp. QJX-1 using tyrosine (Tyr) as the sole carbon and nitrogen source to investigate the effects of seven MPs on its growth and function. Six MPs exhibited an inhibition effect on bacterial growth and Mn(II) oxidation. Only benzophenone-4 (BP-4) promoted the growth of QJX-1 and biogenic oxidation Mn(II), but its concentration was not directly coupled to growth, which was unexpected. RNA-seq data suggested that the addition of BP-4 did not significantly change the basic metabolic function of QJX-1, but stimulated the upregulation of the pyruvate and gluconeogenesis metabolic pathways of Tyr for QJX-1 growth. Furthermore, protein identification and extracellular superoxide detection indicated that Mn(II) oxidation was largely driven by the formation of superoxide in response to Tyr starvation; the acceleration of superoxide production, due to BP-4 accelerating Tyr consumption, was responsible for the promotion effect of BP-4 on QJX-1 Mn(II) oxidation. Our findings highlight the dual effects that MPs can have on the growth and function of a single strain in aquatic ecosystem, i.e., the coexistence of inhibition and promotion.