Efficient photocatalytic degradation of organics present in gas and liquid phases using Pt-TiO2/Zeolite (H-ZSM)

Reduction of CO2 emission through a photocatalytic process using powder and coated zeolite-supported TiO2 under concentrated sunlight irradiation

The efficiency of a novel synthetic zeolite (Ze) prepared from stone cutting sludge and a natural zeolite (clinoptilolite, Cp) as the support of TiO₂ photocatalyst was examined for the CO₂ removal under solar irradiation using a designed parabolic trough collector (PTC). The used samples were characterized using XRF, BET, SEM/EDS, and XPS analyses. The enhanced sunlight irradiation obtained by PTC increased the performance of CO₂ photocatalytic removal. The maximum CO₂ adsorption by TiO₂-Ze and TiO₂-Cp composites was 21.1% and 28.4% which increased to 61.8% and 78.9% under sunlight irradiation, respectively. The efficiency of zeolite-TiO₂ composites for CO₂ removal was approximately two times higher than zeolites and TiO₂ alone. The performance of TiO₂-Ze-coated composite with lower use of photocatalyst for CO₂ adsorption and photocatalytic removal was better than that of powder one. Regeneration of TiO₂-Ze using NaOH solution improved its removal efficiency. The adsorption behavior of CO₂ on TiO₂-Ze composite was well described by the Langmuir isotherm and the pseudo-first-order kinetic model. This work promises CO₂ reduction using natural and synthetic zeolite as an efficient photocatalyst support under solar irradiation.

Conversion of Plastic Waste into Supports for Nanostructured Heterogeneous Catalysts: Application in Environmental Remediation

Plastics are ubiquitous in our society and are used in many industries, such as packaging, electronics, the automotive industry, and medical and health sectors, and plastic waste is among the types of waste of higher environmental concern. The increase in the amount of plastic waste produced daily has increased environmental problems, such as pollution by micro-plastics, contamination of the food chain, biodiversity degradation and economic losses. The selective and efficient conversion of plastic waste for applications in environmental remediation, such as by obtaining composites, is a strategy of the scientific community for the recovery of plastic waste. The development of polymeric supports for efficient, sustainable, and low-cost heterogeneous catalysts for the treatment of organic/inorganic contaminants is highly desirable yet still a great challenge; this will be the main focus of this work. Common commercial polymers, like polystyrene, polypropylene, polyethylene therephthalate, polyethylene and polyvinyl chloride, are addressed herein, as are their main physicochemical properties, such as molecular mass, degree of crystallinity and others. Additionally, we discuss the environmental and health risks of plastic debris and the main recycling technologies as well as their issues and environmental impact. The use of nanomaterials raises concerns about toxicity and reinforces the need to apply supports; this means that the recycling of plastics in this way may tackle two issues. Finally, we dissert about the advances in turning plastic waste into support for nanocatalysts for environmental remediation, mainly metal and metal oxide nanoparticles.

Preparation of Ag-TiO2/Sr4Al14O25:Eu2+,Dy3+ Photocatalyst on Phosphor Beads and Its Photoreaction Characteristics

Long-lasting Sr4Al14O25:Eu2+,Dy3+ phosphor beads were prepared with inorganic sodium silicate binders and coated to support Ag-doped TiO2 catalyst by the sol–gel coating method. Energy dispersive spectroscopy and X-ray photoelectron spectroscopy confirmed that Ag and TiO2 were loaded on the bead surface. Photocatalytic degradation of toluene volatile organic compound was evaluated under ultraviolet and visible light through 410 nm filters. The photocatalyst/phosphor beads of Ag-TiO2/Sr4Al14O25:Eu2+,Dy3+ decorated with 0.035 M Ag in N2 and N2-H2 atmospheres exhibited higher photocatalytic efficiencies compared with beads heat treated in air. A low amount of Ag impregnation and the reducing atmosphere of N2/N2-H2 were beneficial for enhancing photocatalytic efficiency because Ag-doping in TiO2 imparted low energy levels for visible light sensitization. The synthesized powder-free beads possess compressive strength for possible applications, and easy recovery of the photocatalysts is beneficial for preventing any secondary pollution of nano-powders.

Ultrasound-assisted synthesis of ZnO photocatalysts for gas phase pollutant remediation: Role of the synthetic parameters and of promotion with WO3

The synthesis of ZnO photocatalysts by ultrasound-assisted technique was here investigated. Several experimental parameters including the zinc precursor (acetate, chloride, nitrate), sonication conditions (amplitude, pulse) and post-synthetic thermal treatment (up to 500 °C) were studied. Crystalline ZnO samples were obtained without thermal treatments due to the adopted reactant ratios and synthesis temperature. Sonication plays a major role on the morphological oxide features in terms of particle size and surface area, the latter showing a 20-fold increase with respect to conventional synthesis. Interestingly, 1 and 3 s sonication pulses led to morphological properties similar to continuous sonication. A thermal treatment at moderate temperatures (400-450 °C) promoted the loss of surface hydroxylation and the formation of lattice defects, while higher temperatures were detrimental for the sample morphology. The prepared ZnO was decorated with WO₃ particles comparing an ultrasound-assisted technique using 1 s pulses with a conventional approach, giving rise to composites with promoted visible light absorption. Samples were tested towards the photocatalytic degradation of nitrogen oxides (500-1000 ppb) in humidified air under both UV and visible light. By carefully controlling the synthetic procedure, better performance were observed with respect to the commercial benchmark. Samples from ultrasound-assisted syntheses, also in the case of pulsed sonication, showed consistently better results than conventional references, in particular for ZnO-WO₃ composites. The composite by ultrasound-assisted synthesis showed > 95% degradation in 180 min and doubled NO_x degradation under visible light with respect to the conventional composite.

BiOCl/TiO2/diatomite composites with enhanced visible-light photocatalytic activity for the degradation of rhodamine B

A BiOCl/TiO2/diatomite (BTD) composite was synthesized via a modified sol-gel method and precipitation/calcination method for application as a photocatalyst and shows promise for degradation of organic pollutants in wastewater upon visible-light irradiation. In the composite, diatomite was used as a carrier to support a layer of titanium dioxide (TiO2) nanoparticles and bismuth oxychloride (BiOCl) nanosheets. The results show that TiO2 nanoparticles and BiOCl nanosheets uniformly cover the surface of diatomite and bring TiO2 and BiOCl into close proximity. Rhodamine B was used as the target degradation product and visible light (λ > 400 nm) was used as the light source for the evaluation of the photocatalytic properties of the prepared BTD composite. The results show that the catalytic performance of the BTD composite under visible-light irradiation is much higher than that of TiO2 or BiOCl alone. When the molar ratio of BiOCl to TiO2 is 1:1 and the calcination temperature is 400 °C, the composite was found to exhibit the best catalytic effect. Through the study of the photocatalytic mechanism, it is shown that the strong visible-light photocatalytic activity of the BTD composite results mainly from the quick migration of photoelectrons from the conduction band of TiO2/diatomite to the surface of BiOCl, which promotes the separation effect and reduces the recombination rate of the photoelectron-hole pair. Due to the excellent catalytic performance, the BTD composite shows great potential for wide application in the field of sewage treatment driven by solar energy.

High-silica zeolites for adsorption of organic micro-pollutants in water treatment: A review

High-silica zeolites have been found to be effective adsorbents for the removal of organic micro-pollutants (OMPs) from impaired water, including various pharmaceuticals, personal care products, industrial chemicals, etc. In this review, the properties and fundamentals of high-silica zeolites are summarised. Recent research on mechanisms and efficiencies of OMP adsorption by high-silica zeolites are reviewed to assess the potential opportunities and challenges for the application of high-silica zeolites for OMP adsorption in water treatment. It is concluded that the adsorption capacities are well-related to surface hydrophobicity/hydrophilicity and structural features, e.g. micropore volume and pore size of high-silica zeolites, as well as the properties of OMPs. By using high-silica zeolites, the undesired competitive adsorption of background organic matter (BOM) in natural water could potentially be prevented. In addition, oxidative regeneration could be applied on-site to restore the adsorption capacity of zeolites for OMPs and prevent the toxic residues from re-entering the environment.

Electrochemical oxidation of 4-chlorophenol for wastewater treatment using highly active UV treated TiO2 nanotubes

In the present work, we report on a facile UV treatment approach for enhancing the electrocatalytic activity of TiO₂ nanotubes. The TiO₂ nanotubes were prepared using an anodization oxidation method by applying a voltage of 40 V for 8 h in a DMSO + 2% HF solution, and further treated under UV light irradiation. Compared with Pt and untreated TiO₂ nanotubes, the UV treated electrode exhibited a superior electrocatalytic activity toward the oxidation of 4-chlorophenol (4-ClPh). The effects of current density and temperature on the electrochemical oxidation of the 4-ClPh were also systematically investigated. The high electrocatalytic activity of the UV treated TiO₂ nanotubes was further confirmed by the electrochemical oxidation of other persistent organic pollutants including phenol, 2-, 3-, 4-nitrophenol, and 4-aminophenol. The total organic carbon (TOC) analysis revealed that over 90% 4-ClPh was removed when the UV treated TiO₂ electrode was employed and the rate constant was 16 times faster than that of the untreated TiO₂ electrode; whereas only 60% 4-ClPh was eliminated at the Pt electrode under the same conditions. This dramatically improved electrocatalytic activity might be attributed to the enhanced donor density, conductivity, and high overpotential for oxygen evolution. Our results demonstrated that the application of the UV treatment to the TiO₂ nanotubes enhanced their electrochemical activity and energy consumption efficiency significantly, which is highly desirable for the abatement of persistent organic pollutants.

Is nano ZrO2 a better photocatalyst than nano TiO2 for degradation of plastics?

The environmental accumulation of plastic is a huge problem due to its low degradability.