Bactericidal and catalytic performance of green nanocomposite based-on chitosan/carbon black fiber supported monometallic and bimetallic nanoparticles

Salt-resistant continuous solar evaporation composites based on nonwovens with synergistic photothermal effect of graphene oxide/copper sulphide

Solar interfacial evaporation is an innovative and environmentally friendly technology for producing freshwater from seawater. However, current interfacial evaporators are costly to manufacture, have poor tolerance to environmental conditions, exhibit instability in evaporation efficiency in highly saline solutions, and fail to prevent salt crystallization. The production of user-friendly, durable and salt-resistant interfacial evaporators remains a significant challenge. By spraying graphene oxide on a nonwoven material using PVA as a binder and adding biphasic Cu x S by an in situ growth method, we designed 2D/3D micro- and nanostructured graphene oxide nanosheets/copper sulfide nanowires (GO/Cu x S) with synergistic photo-thermal effects in the full spectral range. The evaporation efficiency in pure water was 94.61% with an evaporation rate of 1.5622 kg m-2 h-1. In addition, we enhanced convection by employing a vertically aligned water-guide rod structure design, where the concentration difference drives salt dissolution thereby reducing the formation of salt crystals. The evaporation efficiency in 20% salt water was 80.41% with an evaporation rate of 1.3228 kg m-2 h-1 and long-term stability of brine evaporation was demonstrated under continuous sunlight. This solar steam generator expands the potential application areas of desalination and wastewater purification.

Carbon based nanocomposites, surface functionalization as a promising material for VOCs (volatile organic compounds) treatment

Urban residential and industrial growth development affects sustainable and healthful indoor environments. Environmental issues are a global problem. The deterioration of indoor air quality has prompted the creation of several air cleansing techniques. This review explains how carbon-based materials have influenced the development of air purification systems using photocatalysis. These carbon-based materials offer unique properties and advantages in VOC removal processes. Biochar, produced from biomass pyrolysis, provides an environmentally sustainable solution with its porous structure and carbon-rich composition. Carbon quantum dots, with their quantum confinement effects and tunable surface properties, show promise in VOC sensing and removal applications. Polymers incorporating reduced graphene oxide demonstrate enhanced adsorption capabilities owing to the synergistic effects of graphene and polymer matrices. Activated carbon fibers, characterized by their high aspect ratio and interconnected porosity, provide efficient VOC removal with rapid kinetics. With their unique electronic and structural properties, graphitic carbon nitrides offer opportunities for photocatalytic degradation of VOCs under visible light. Catalysts integrated with MXene, a two-dimensional nanomaterial, exhibit enhanced catalytic activity for VOC oxidation reactions. Using various carbon-based materials in VOC removal showcases the versatility and effectiveness of carbon-based approaches in addressing environmental challenges associated with indoor air pollution. Metal-organic-framework materials are carbon-based compounds. It examines the correlation between VOC mineralization and specific characteristics of carbon materials, including surface area, adsorption capability, surface functional groups, and optoelectronic properties. Discussions include the basics of PCO, variables influencing how well catalysts degrade, and degradation mechanisms. It explores how technology will improve in the future to advance studies on healthy and sustainable indoor air quality.

Robust polymer hybrid and assembly materials from structure tailoring to efficient catalytic remediation of emerging pollutants

A massive amount of toxic substances and harmful chemicals are released every day into the outer environment, imposing serious environmental impacts on both land and aquatic animals. To date, research is constantly in progress to determine the best catalytic material for the effective remediation of these harmful pollutants. Hybrid nanomaterials prepared by combining functional polymers with inorganic nanostructures got attention as a promising area of research owing to their remarkable multifunctional properties deriving from their entire nanocomposite structure. The versatility of the existing nanomaterials' design in polymer-inorganic hybrids, with respect to their structure, composition, and architecture, opens new prospects for catalytic applications in environmental remediation. This review article provides comprehensive detail on catalytic polymer nanocomposites and highlights how they might act as a catalyst in the remediation of toxic pollutants. Additionally, it provides a detailed clarification of the processing of design and synthetic ways for manufacturing polymer nanocomposites and explores further into the concepts of precise design methodologies. Polymer nanocomposites are used for treating pollutants (electrocatalytic, biocatalytic, catalytic, and redox degradation). The three catalytic techniques that are frequently used are thoroughly illustrated. Furthermore, significant improvements in the method through which the aforementioned catalytic process and pollutants are extensively discussed. The final section summarizes challenges in research and the potential of catalytic polymer nanocomposites for environmental remediation.

A composite of AgNPs and lignin porous microspheres via in-situ reduction of Ag+ and its catalytic performance

Despite the widespread utilization of nano silver composites in the domain of catalytic hydrogenation of aromatic pollutants in wastewater, certain challenges persist, including the excessive consumption of chemical reagents during the preparation process and the difficulty in recycling. In this study, silver ions were reduced in-situ by taking advantage of the adsorptive and reducing capacities of hydroxyls and amino groups on lignin porous microspheres (LPMs) under mild ultrasonic conditions, and lignin porous microspheres loaded with silver nanoparticles (Ag@LPMs) were conveniently prepared. Ag@LPMs had excellent catalytic and cycling performances for p-nitrophenol (4-NP), methylene blue (MB) and methyl orange (MO). The 4-NP could be completely reduced to 4-AP within 155 s under the catalysis of Ag@LPMs, with a pseudo-first-order kinetic constant of 1.28 min-1. Furthermore, Ag@LPMs could still complete the catalytic reduction of 4-NP within 10 min after five cycles. Ag@LPMs with the particle size ranging from 100 to 200 μm conferred ease of recycling, and the porous structure effectively resolved the issue of sluggish mass transfer encountered during the catalytic process. At the same time, the binding force of nano silver and LPMs obtained by ultrasonic was stronger than that of heating, so the materials prepared by ultrasonic had better cycling performance. Silver ions concentration and pH value in the preparation process affected the catalytic performance of Ag@LPMs, 50 mmol/L Ag+ and pH value of 7 turned out to be the optimization conditions.

Harnessing the potential of bimetallic nanoparticles: Exploring a novel approach to address antimicrobial resistance

The growing global importance of antimicrobial resistance (AMR) in public health has prompted the creation of innovative approaches to combating the issue. In this study, the promising potential of bimetallic nanoparticles (BMNPs) was investigated as a novel weapon against AMR. This research begins by elaborating on the gravity of the AMR problem, outlining its scope in terms of the effects on healthcare systems, and stressing the urgent need for novel solutions. Because of their unusual features and wide range of potential uses, bimetallic nanoparticles (BMNPs), which are tiny particles consisting of two different metal elements, have attracted a lot of interest in numerous fields. This review article provides a comprehensive analysis of the composition, structural characteristics, and several synthesis processes employed in the production of BMNPs. Additionally, it delves into the unique properties and synergistic effects that set BMNPs apart from other materials. This review also focuses on the various antimicrobial activities shown by bimetallic nanoparticles, such as the rupturing of microbial cell membranes, the production of reactive oxygen species (ROS), and the regulation of biofilm formation. An extensive review of in vitro studies confirms the remarkable antibacterial activity of BMNPs against a variety of pathogens and sheds light on the dose-response relationship. The efficacy and safety of BMNPs in practical applications are assessed in this study. It also delves into the synergistic effects of BMNPs with traditional antimicrobial drugs and their ability to overcome multidrug resistance, providing mechanistic insight into these phenomena. Wound healing, infection prevention, and antimicrobial coatings on medical equipment are only some of the clinical applications of BMNPs that are examined, along with the difficulties and possible rewards of clinical translation. This review covers nanoparticle-based antibacterial regulation and emerging uses. The essay concludes with prospects for hybrid systems, site-specific targeting, and nanoparticle-mediated gene and drug delivery. In summary, bimetallic nanoparticles have surfaced as a potential solution, offering the public a more promising and healthier future.

Active metals decorated NiCo2O4 yolk-shell nanospheres as nanoreactors for catalytic reduction of nitroarenes and azo dyes

Transition-metal oxides (TMOs) have received a great deal of research attention and have been widely used in a variety of fields. However, conventional TMOs do not possess high specific surface area, sufficient active site on their surfaces, and limited their applications in catalysis. This study presents a two-step method for synthesizing active metal (M) decorated NiCo2O4 (M/NiCo2O4, M = Pd or Cu) nanospheres with yolk-shell nanostructures. Taking advantage of the unique morphology and the combination of dual active components (i.e., active NiCo2O4 substrate and decorated active metal), the as-prepared M/NiCo2O4 yolk-shell nanospheres can be employed as nanoreactors in the organic reactions. In catalyzing the reduction of a representative nitroarene (i.e., 4-NP) by NaBH4, the Pd/NiCo2O4 nanoreactors exhibit a superior catalytic efficiency to their counterparts (Cu/NiCo2O4 and NiCo2O4). The turnover frequency is much higher than that of various TMOs supported nanocatalysts have been reported over the past five years. Furthermore, the Pd/NiCo2O4 nanoreactors show excellent stability and common applicability of the reduction of various substituted nitrobenzenes and azo dyes. This work provides new rational design concept and preparation strategy for efficient nanoreactors with dual active components and sheds light on the practical application of chemical reactions.

An efficient wastewater treatment through reduction of organic dyes using Ag nanoparticles supported on cellulose gum beads

This work reports silver nanoparticles (AgNPs) supported on biopolymer carboxymethyl cellulose beads (Ag-CMC) serves as an efficient catalyst in the reduction process of p-nitrophenol (p-NP) and methyl orange (MO). For Ag-CMC synthesis, first CMC beads were prepared by crosslinking the CMC solution in aluminium nitrate solution and then the CMC beads were introduced into AgNO3 solution to adsorb Ag ions. Field emission scanning electron microscopy (FE-SEM) analysis suggests the uniform distribution of Ag nanoparticles on the CMC beads. The X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis revealed the metallic and fcc planes of AgNPs, respectively, in the Ag-CMC catalyst. The Ag-CMC catalyst exhibits remarkable reduction activity for the p-NP and MO dyes with the highest rate constant (kapp) of a chemical reaction is 0.519 and 0.697 min-1, respectively. Comparative reduction studies of Ag-CMC with CMC, Fe-CMC and Co-CMC disclosed that Ag-CMC containing AgNPs is an important factore in reducing the organic pollutants like p-NP and MO dyes. During the recyclability tests, the Ag-CMC also maintained high reduction activity, which suggests that CMC protects the AgNPs from leaching during dye reduction reactions.

Catalytic polymer nanocomposites for environmental remediation of wastewater

The removal of harmful chemicals and species from water, soil, and air is a major challenge in environmental remediation, and a wide range of materials have been studied in this regard. To identify the optimal material for particular applications, research is still ongoing. Polymer nanocomposites (PNCs), which combine the benefits of nanoparticles with polymers, an alternative to conventional materials, may open up new possibilities to overcome this difficulty. They have remarkable mechanical capabilities and compatibility due to their polymer matrix with a very high surface area to volume ratio brought about by their special physical and chemical properties, and the extremely reactive surfaces of the nanofillers. Composites also provide a viable answer to the separation and reuse problems that hinder nanoparticles in routine use. Understanding these PNCs materials in depth and using them in practical environmental applications is still in the early stages of development. The review article demonstrates a crisp introduction to the PNCs with their advantageous properties as a catalyst in environmental remediation. It also provides a comprehensive explanation of the design procedure and synthesis methods for fabricating PNCs and examines in depth the design methods, principles, and design techniques that guide proper design. Current developments in the use of polymer nanocomposites for the pollutant treatment using three commonly used catalytic processes (catalytic and redox degradation, electrocatalytic degradation, and biocatalytic degradation) are demonstrated in detail. Additionally, significant advances in research on the aforementioned catalytic process and the mechanism by which contaminants are degraded are also amply illustrated. Finally, there is a summary of the research challenges and future prospects of catalytic PNCs in environmental remediation.

Bimetallic (Ag and MgO) nanoparticles, Aloe vera extracts loaded xanthan gum nanocomposite for enhanced antibacterial and in-vitro wound healing activity

We prepared nanocomposite (XG-AVE-Ag/MgO NCs) using the bimetallic Ag/MgO NPs, Aloe vera extract (AVE), and biopolymer (Xanthan gum (XG)) to archive a synergetic antibacterial and wound healing activity. The changes in XRD peaks at 20° of XG-AVE-Ag/MgO NCs indicated the XG encapsulation. The XG-AVE-Ag/MgO NCs showed the zeta potential and zeta size of 151.3 ± 3.14 d·nm and -15.2 ± 1.08 mV with a PDI of 0.265 while TEM showed an average size of 61.19 ± 3.89. The EDS confirmed the co-existence of Ag, Mg, carbon, oxygen, and nitrogen in NCs. XG-AVE-Ag/MgO NCs displayed higher antibacterial activity in terms of zone of inhibition, at 15.00 ± 0.12 mm for B. cereus and 14.50 ± 0.85 mm for E. coli. Moreover, NCs exhibited MICs of 2.5 μg/mL for E. coli, and 0.62 μg/mL for B. cereus. The in vitro cytotoxicity and hemolysis assays indicated the non-toxic properties of XG-AVE-Ag/MgO NCs. The higher wound closure activity was observed with the treatment of XG-AVE-Ag/MgO NCs (91.19 ± 1.87 %) compared to the control, untreated group (68.68 ± 3.54 %) at 48 h of incubation. These findings revealed that XG-AVE-Ag/MgO NCs was promising non-toxic, antibacterial, and wound-healing agent that deserved further in-vivo studies.

Versatile mechanisms and enhanced strategies of pollutants removal mediated by Shewanella oneidensis: A review

The removal of environmental pollutants is important for a sustainable ecosystem and human health. Shewanella oneidensis (S. oneidensis) has diverse electron transfer pathways and can use a variety of contaminants as electron acceptors or electron donors. This paper reviews S. oneidensis's function in removing environmental pollutants, including heavy metals, inorganic non-metallic ions (INMIs), and toxic organic pollutants. S. oneidensis can mineralize o-xylene (OX), phenanthrene (PHE), and pyridine (Py) as electron donors, and also reduce azo dyes, nitro aromatic compounds (NACs), heavy metals, and iodate by extracellular electron transfer (EET). For azo dyes, NACs, Cr(VI), nitrite, nitrate, thiosulfate, and sulfite that can cross the membrane, S. oneidensis transfers electrons to intracellular reductases to catalyze their reduction. However, most organic pollutants cannot be directly degraded by S. oneidensis, but S. oneidensis can remove these pollutants by self-synthesizing catalysts or photocatalysts, constructing bio-photocatalytic systems, driving Fenton reactions, forming microbial consortia, and genetic engineering. However, the industrial-scale application of S. oneidensis is insufficient. Future research on the metabolism of S. oneidensis and interfacial reactions with other materials needs to be deepened, and large-scale reactors should be developed that can be used for practical engineering applications.

Fabrication of 3D Gelatin Hydrogel Nanocomposite Impregnated Co-Doped SnO2 Nanomaterial for the Catalytic Reduction of Environmental Pollutants

In the catalytic reduction of various environment pollutants, cobalt-doped tin oxide, i.e., Co-SnO₂ intercalated gelatin (GL) hydrogel nanocomposite was prepared via direct mixing of Co-SnO₂ doped with GL. Then, it was crosslinked internally using formaldehyde within a viscous solution of gelatin polymer, which led to the formation of GL/Co-SnO₂ hydrogel nanocomposite. GL/Co-SnO₂ hydrogel nanocomposite was fully characterized by using field-emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDX), powder X-ray diffraction (XRD), and attenuated total reflection–Fourier transform infrared spectroscopy (ATR-FTIR). The FESEM images indicate that the Co-SnO₂ composite has a spherical structure on the GL matrix while EDX elucidates the elemental composition of each atom in the crosslinked GL/Co-SnO₂ hydrogel nanocomposite. The GL/Co-SnO₂ nanocomposite was checked for the reduction of various pollutants, including 2-nitro-phenol (2-NP), 2,6-dinitro-phenol (2,6-DNP), 4-nitro-phenol (4-NP), Congo red (CR), and methyl orange (MO) dyes with a strong sodium borohydride (NaBH₄) reducing agent. The GL/Co-SnO₂ nanocomposite synergistically reduced the MO in the presence of the reducing agent with greater reduction rate of 1.036 min⁻¹ compared to other dyes. The reduction condition was optimized by changing various parameters, such as the catalyst amount, dye concentration, and the NaBH₄ amount. Moreover, the GL/Co-SnO₂ nanocomposite catalyst can be easily recovered, is recyclable, and revealed minimal loss of nanomaterials.

Sequestration of crystal violet dye from wastewater using low-cost coconut husk as a potential adsorbent

The current study explores the effectiveness of coconut husk for crystal violet dye sequestration employing a batch experimental setup. Characterization of adsorbent was carried out via FTIR, and SEM techniques and results confirmed the involvement of -OMe, -COC- and hydroxyl functional groups in dye uptake, and the rough, porous nature of adsorbent and after adsorption dye molecules colonized these holes resulting in dye exclusion. Effects of various adsorption parameters such as pH, adsorbent dose, contact time, initial dye concentration, and temperature of solution were studied. Crystal violet adsorption on coconut husk was highly pH-dependent, with maximum removal occurring at basic pH. Maximum removal of dye, i.e., 81%, takes place at optimized conditions. Kinetic data was analyzed by pseudo-first, pseudo-second order and an intra-particle diffusion model. Results showed that the pseudo-second order kinetic model best described adsorption of crystal violet onto coconut husk. Langmuir, Freundlich, and D-R adsorption isotherms were also used to test their appropriateness to experimental data and the Freundlich isotherm fits best to data. Thermodynamic parameters showed that the current process was spontaneous, endothermic in nature with continuous decrease in entropy. Established practice is 79% applicable to tap water and in acidic medium nearly 80% of adsorbent was recovered, confirming the effectiveness and appropriateness of coconut husk for crystal violet dye exclusion from wastewater.

Catalytic Reduction of Environmental Pollutants with Biopolymer Hydrogel Cross-Linked Gelatin Conjugated Tin-Doped Gadolinium Oxide Nanocomposites

In the present study, a biopolymer nanocomposite hydrogel based on gelatin and tin-doped gadolinium oxide (Sn-Gd₂O₃@GH) was prepared for the efficient reduction of water pollutants. The method of Sn-Gd₂O₃@GH preparation consisted of two steps. A Sn-Gd₂O₃ nanomaterial was synthesized by a hydrothermal method and mixed with a hot aqueous solution (T > 60 °C) of gelatin polymer, followed by cross-linking. Due to the presence of abundant functional groups on the skeleton of gelatin, such as carboxylic acid (–COOH) and hydroxyl (–OH), it was easily cross-linked with formaldehyde. The structure, morphology, and composition of Sn-Gd₂O₃@GH were further characterized by the FESEM, XRD, EDX, and FTIR techniques. The FESEM images located the distribution of the Sn-Gd₂O₃ nanomaterial in a GH matrix of 30.06 nm. The XRD patterns confirmed the cubic crystalline structure of Gd₂O₃ in a nanocomposite hydrogel, while EDS elucidated the elemental composition of pure Sn-Gd₂O₃ powder and cross-linked the Sn-Gd₂O₃@GH samples. The synthesized Sn-Gd₂O₃@GH nanocomposite was used for the removal of different azo dyes and nitrophenols (NPs). It exhibited an efficient catalytic reduction of Congo red (CR) with a reaction rate of 9.15 × 10⁻¹ min⁻¹ with a strong NaBH₄-reducing agent. Moreover, the Sn-Gd₂O₃@GH could be easily recovered by discharging the reduced (colourless) dye, and it could be reused for a fresh cycle.

In situ green synthesis of lysozyme/silver nanoparticles sol and their antimicrobial properties

Lysozyme/silver nanoparticles sol (LZM/AgNPs) were synthesized in situ with the assistance of ultraviolet irradiation with enhanced antibacterial activity.

Catalytic reduction of 4-nitrophenol and methylene blue pollutants in water by copper and nickel nanoparticles decorated polymer sponges

In the present study, two catalysts based-on copper and nickel nanoparticles anchored on agarose-coated sponge (Cu-AG-sponge and Ni-AG-sponge) were prepared, respectively. Both catalysts were characterized by analytical techniques of thermogravimetric analysis energy dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM). Spherical Cu and Ni nanoparticles on struts of AG-coated sponge were observed by FESEM and the samples' elemental composition was confirmed by EDX technique. After characterization, the Cu-AG-sponge and Ni-AG-sponge catalysts were tested in 4-nitrophenol (4-NP) and methylene blue dye (MB) reduction in an aqueous medium. The reduction of the 4-NP to 4-aminophenol (4-AP) was achieved up to 95% using the NaBH₄ reductant and Cu-AG-sponge and Ni-AG-sponge catalysts, respectively. Similarly, the rate of reduction of MB was faster for the Cu-AG-sponge as compared to the Ni-AG-sponge which was discussed based-on the catalyst morphology and other factors. The high rate of reactions for the 4-NP and MB reduction suggests that the Cu-AG-sponge and Ni-AG-sponge catalyst possess high catalytic efficiency, low cost and good reusability having the potential to be used in similar other reactions.

Chitosan Natural Polymer Material for Improving Antibacterial Properties of Textiles

In recent years, the textile industry has been seeking to develop innovative products. It is a good choice to organically combine materials with superior functional characteristics and commercial textiles to form products with excellent performance. In particular, textiles made of biological functional materials are often beneficial to human health, which is an interesting research direction. As a biopolymer material, chitosan has the advantages of strong availability, low cost, excellent safety, outstanding performance, etc., particularly the antibacterial property, and has broad application prospects in the textile field. This review provides an overview of the latest literature and summarizes recent innovations and state-of-the-art technologies that can add value to textiles. To this end, preparation of chitosan fiber, synthesis of chitosan nanofiber, antibacterial activity of chitosan fiber, antibacterial activity of chitosan nanofiber, etc., will be discussed. Furthermore, the challenges and prospects of chitosan-based materials used in textiles are evaluated. Importantly, this review can not only help researchers understand the development status of antibacterial textiles, but also help researchers discover and solve problems in this field through comparative reading.

Microwave-assisted fabrication of g-C3N4 nanosheets sustained Bi2S3 heterojunction composites for the catalytic reduction of 4-nitrophenol

In this work, we report a stable g-C₃N₄, Bi₂S₃, and g-C₃N₄/Bi₂S₃ composite catalysts were prepared via a facile one-pot microwave-assisted method and characterized. The orthorhombic phase and nearly spherical shape of the particles with an average diameter of 5-25 nm of g-C₃N₄/Bi₂S₃ composite were obtained from XRD and TEM. The composite also exhibits a high surface area (32.15 m²/g), which may provide convenient transportation and diffusion for substrate molecule. The optical studies were displayed the g-C₃N₄/Bi₂S₃ composite has a sharp absorption band in the visible region, higher charge separation, and reduced recombination rate. These results show that the Bi₂S₃ NPs have good crystallinity and are uniformly deposited on the surface of the g-C₃N₄ sheet. The catalytic performance of the g-C₃N₄/Bi₂S₃ composite for the reduction of 4-NP to 4-AP was exhibited approximately 100%, which is 1.48 and 2.34 times higher than the Bi₂S₃ and g-C₃N₄ catalysts, respectively. The pseudo-first-order rate constant was estimated as 1.648 × 10 ^-2 min^-1 for the reduction of 4-NP using g-C₃N₄/Bi₂S₃ composite in 1 h reaction time. The effect of catalyst dosage (0-30 mg) was also investigated for the reduction of 4-NP using g-C₃N₄/Bi₂S₃ composite catalyst. Moreover, the reusability of the g-C₃N₄/Bi₂S₃ composite was exhibited a better reduction of the 4-NP even after 5 cycles and it was found that 8% reduction in the initial reduction rate. The obtained results from this study show that g-C₃N₄/Bi₂S₃ composite has the potential efficiency and stability to make it an ideal catalyst for the reduction of toxic effluents and wastewater treatment.

Facile synthesis of easily separated and reusable silver nanoparticles/aminated alkaline lignin composite and its catalytic ability

Green synthesis of silver nanoparticles (AgNPs) has received increasing attention. In this study, AgNPs were prepared through in-situ reduction by aminated alkaline lignin (AAL). Compared with alkaline lignin (AL), AAL exhibited stronger reduction capacity (increased by 36%) due to the introduced amine groups and better water solubility. Moreover, the coordination effect of amine groups on AAL improved the binding force between lignin and AgNPs. The content of AgNPs in AgNPs/AAL composite were 2.4 times higher than that in AgNPs/AL, such content could be further increased through increasing the reduction pH or prolonging the heating time. The results of XPS, XRD and TEM showed that the AgNPs were spherical and monodisperse with an average particle size about 17 nm. Additionally, the size of AgNPs was affected by the amination degree of lignin. AgNPs/AAL exhibited good catalytic performance for the reduction of 4-nitrophenol to 4-aminophenol, and this compound could be easily recovered and reused for at least eight cycles.

Catalytic potential of cobalt oxide and agar nanocomposite hydrogel for the chemical reduction of organic pollutants

In this study, cobalt oxide nanoparticles (Co₃O₄ NPs) were synthesized by precipitation method from cobalt sulphate solution with basic pH, followed by calcination. The ex-situ synthesized Co₃O₄ NPs were mixed with hot agar (AG) aqueous solution. The preparation of AG- Co₃O₄ nanocomposite hydrogel was carried out by self-association method promoted by thermal denaturation. The quenching of hot suspension from 80 °C to room temperature resulted in the formation of AG-Co₃O₄ nanocomposite hydrogel. The as-synthesized AG-Co₃O₄ was characterized by FTIR, XRD and SEM techniques. In order to test the catalytic activity, AG-Co₃O₄ was used as a heterogeneous catalyst for the reduction of methylene blue (MB), congo red (CR) and 4-nitrophenol (4-NP). The excellent performance of the AG-Co₃O₄ was shown by the reaction rate constant (k_app) values of 0.3623, 0.2114 and 0.2893 for MB, 4-NP and CR, respectively. All these results were obtained with R² above 94 and utilization of an AG-Co₃O₄ catalyst. Furthermore, the catalytic reduction was studied with varying dye concentration and catalyst dose. This study showed that AG-Co₃O₄ catalyst has high potential for remediation of environmental pollutants in wastewaters.

Switching from Conventional to Nano-natural Phytochemicals to Prevent and Treat Cancers: Special Emphasis on Resveratrol

BACKGROUND

Natural phytochemicals and their derivatives have been used in medicine since prehistoric times. Natural phytochemicals have potential uses against various disorders, including cancers. However, due to low bioavailability, their success in clinical trials has not been reproduced. Nanotechnology has played a vital role in providing new directions for diagnosis, prevention, and treatment of different disorders, and of cancer in particular. Nanotechnology has demonstrated the capability to deliver conventional natural products with poor solubility or a short half-life to target specific sites in the body and regulate the release of drugs. Among the natural products, the phytoalexin resveratrol has demonstrated therapeutic effects, including antioxidant, antiinflammatory, and anti-proliferative effects, as well as the potential to inhibit the initiation and promotion of cancer. However, low water solubility and extensive first-pass metabolism lead to poor bioavailability of resveratrol, hindering its potential. Conventional dosage forms of resveratrol, such as tablets, capsules, dry powder, and injections, have met with limited success. Nanoformulations are now being investigated to improve the pharmacokinetic characteristics, as well as to enhance the bioavailability and targetability of resveratrol.

OBJECTIVES

This review details the therapeutic effectiveness, mode of action, and pharmacokinetic limitations of resveratrol, as well as discusses the successes and challenges of resveratrol nanoformulations. Modern nanotechnology techniques to enhance the encapsulation of resveratrol within nanoparticles and thereby enhance its therapeutic effects are emphasized.

CONCLUSION

To date, no resveratrol-based nanosystems are in clinical use, and this review would provide a new direction for further investigations on innovative nanodevices that could consolidate the anticancer potential of resveratrol.

Pollution, Toxicity and Carcinogenicity of Organic Dyes and their Catalytic Bio-Remediation

Water pollution due to waste effluents of the textile industry is seriously causing various health problems in humans. Water pollution with pathogenic bacteria, especially Escherichia coli (E. coli) and other microbes is due to the mixing of fecal material with drinking water, industrial and domestic sewage, pasture and agricultural runoff. Among the chemical pollutants, organic dyes due to toxic nature, are one of the major contaminants of industrial wastewater. Adequate sanitation services and drinking quality water would eliminate 200 million cases of diarrhea, which results in 2.1 million less deaths caused by diarrheal disease due to E. coli each year. Nanotechnology is an excellent platform as compared to conventional treatment methods of water treatment and remediation from microorganisms and organic dyes. In the current study, toxicity and carcinogenicity of the organic dyes have been studied as well as the remediation/inactivation of dyes and microorganism has been discussed. Remediation by biological, physical and chemical methods has been reviewed critically. A physical process like adsorption is cost-effective, but can't degrade dyes. Biological methods were considered to be ecofriendly and cost-effective. Microbiological degradation of dyes is cost-effective, eco-friendly and alternative to the chemical reduction. Besides, certain enzymes especially horseradish peroxidase are used as versatile catalysts in a number of industrial processes. Moreover, this document has been prepared by gathering recent research works related to the dyes and microbial pollution elimination from water sources by using heterogeneous photocatalysts, metal nanoparticles catalysts, metal oxides and enzymes.

Bimetallic Nanoparticles for Antimicrobial Applications

Highly effective antimicrobial agents are needed to control the emergence of new bacterial strains, their increased proliferation capability, and antibacterial resistance that severely impact public health, and several industries including water, food, textiles, and oil and gas. Recently, bimetallic nanoparticles, formed via integration of two different metals, have appeared particularly promising with antibacterial efficiencies surpassing that of monometallic counterparts due to synergistic effects, broad range of physiochemical properties, and diverse mechanisms of action. This work aims to provide a review on developed bimetallic and supported bimetallic systems emphasizing in particular on the relation between synthesis routes, properties, and resulting efficiency. Bimetallic nanostructures on graphene, zeolites, clays, fibers, polymers, as well as non-supported bimetallic nanoparticles are reviewed, their synthesis methods and resulting properties are illustrated, along with their antimicrobial activity and potential against different strains of microbes.

Photodegradation of 4-nitrophenol over B-doped TiO2 nanostructure: effect of dopant concentration, kinetics, and mechanism

The 4-nitrophenol (4-NP) is one of the carcinogenic pollutants listed by US EPA and has been detected in industrial wastewater. This study investigates the photocatalytic degradation of 4-NP with TiO₂ and boron (B)-doped TiO₂ nanostructures. The degradation on undoped and B-doped TiO₂ with various boron loadings (1-7%) was studied to establish a relationship between structure, interface, and photo-catalytic properties. The results of XRD, micro Raman, FTIR, and HRTEM show that the B doping has improved the crystallinity and induces rutile phase along with anatase (major phase). The N₂ adsorption-desorption, SEM-EDX, and XPS indicated that the B induced the formation of mesoporous nanostructures in TiO₂ and occupies interstitial sites by forming Ti-O-B type linkage. The surface area of pure TiO₂ was decreased from 235.4 to 63.3 m²/g in B-TiO₂. The photo-physical properties were characterized by UV-Vis DRS, which showed decrease in the optical band-gap of pure TiO₂ (2.98 eV) to B-TiO₂ (2.95 eV). The degradation results demonstrated that the B doping improved the photocatalytic activity of TiO₂; however, this improvement depends on the B concentration in doped TiO₂. B-doped TiO₂ (> 5% B) showed 90 % degradation of 4-NP, whereas the undoped TiO₂ can degrade only 79 % of 4-NP. The degradation followed pseudo-first-order kinetics with rate constant values of 0.006 min^-1 and 0.0322 min^-1 for pure TiO₂ and B-TiO₂ respectively. The existence of a reduced form of Ti³⁺ on the surface of TiO₂ (as evidence from XPS) was found responsible for enhancement in photocatalytic activity.

Lignocellulosic biomass supported metal nanoparticles for the catalytic reduction of organic pollutants

Lignocellulosic biomass waste is a cheap, eco-friendly, and sustainable raw material for a wide array of applications. In the present study, an easy, fast, and economically feasible route has been proposed for the preparation of different zero-valent metal nanoparticles (ZV-MNPs) based on Cu, Co, Ag, and Ni NPs using empty fruit bunch (EFB) biomass residue as support material. The catalytic efficiency of ZV-MNPs/EFB catalyst was investigated against five model pollutants, such as methyl orange (MO), congo red (CR), methylene blue (MB), acridine orange (AO), and 4-nitrophenol (4-NP) using NaBH₄ as a source of hydrogen and electron. Comparative study revealed that among as-prepared ZV-MNPs/EFB catalysts, Cu-NPs immobilized onto EFB (Cu/EFB) exhibited maximum catalytic efficiency towards pollutant abasement. Degradation reactions were highly efficient, and were completed within a short time (4 min) in case of MO, CR, and MB, whilst AO and 4-NP were reduced in less than 15 min. Kinetic investigation revealed that the degradation rate of model pollutants accorded with pseudo-first order model. Furthermore, supported catalysts were easily recovered after the completion of experiment by simply pulling the catalyst from reaction system. Recyclability tests performed on Cu/EFB revealed that more than 97% of the reduction was achieved in case of MO dye for four successive cycles of reuse. The as-prepared heterostructure showed multifunctional properties, such as enhanced uptake of contaminants, high catalytic efficiency, and easy recovery, hence, offers great prospects in wastewater purification.

Hierarchical porous carbon material restricted Au catalyst for highly catalytic reduction of nitroaromatics

In this study, four kinds of porous carbon materials were used as supports to anchor gold nanoparticles (AuNPs) for catalytic reduction of nitroaromatics and 4-nitrophenol (4-NP) was employed as a model material. Results identified that carbon black (CB) restricted-Au catalyst (Au/CB) provided large specific surface area, small AuNPs size, and low cost, which showed highly catalytic activity for 4-NP reduction. Besides, with the increase of Au loadings, the catalytic activity of Au/CB was enhanced and the 1.2 wt% of Au loading exhibited the best catalytic activity with the high rate of 0.8302 min^-1 and the turnover frequency of 492.50 h^-1. Universality and real water application demonstrated that the as-prepared Au/CB catalyst was promising candidate for other phenols and azo dyes reduction and had great potential for practical application. Furthermore, after ten cycles, Au/CB still retained satisfying stability and activity. These results suggested that the larger specific surface area and smaller particle size attributing to the porosity of CB were conducive to improving the catalytic activity of Au catalysts. This design shows high potential of hierarchical porous carbon materials for highly catalytic reaction in many fields, especially the water purification.

Comparative Synthesis and Characterization of Bio-Cellulose from Local Waste and Cheap Resources

Background:

Bacterial cellulose (BC) has been extensively utilized in a wide range of applications specifically in the biomedical field thanks to its excellent physico-chemical and biological features. The major limitation restricting its application in certain areas is its high production cost. Its widespread applications demand exploration of alternative production media compared to the existing expensive ones. Herein, an effort has been made to utilize waste and cheaply available local resources including; waste (expired) orange juice (WOJ), sugarcane juice (SC) and coconut water (CW) as alternative media for BC production in comparison to the synthetic media (control).

Methods:

Waste and cheap resources were collected from the local market, screened filtered and optimized for the development of BC culture media. BC production from all media was observed under static cultivation for 10 days. The results indicated 2.75, 2.56, 3.32 and 1.68 g/L BC production that corresponded to 27.5%, 21.7 %, 20.1 % and 31.6 % sugar to BC conversion from control, WOJ, SC and CW media, respectively. Morphology and crystalline features of produced BC samples were observed through FE-SEM and XRD analysis. It was noteworthy that BC produced from all alternative sources indicated high water holding capabilities (WHC) and water retention time (WRT) that augment their applicability in drug delivery and wound healing applications.

Conclusion:

The BC production from cheap resources and its high physical, mechanical and biological properties can be of high interest for scaling up and commercialization of BC production processes. Furthermore, its liquidabsorbing capabilities and retention time can help in drug carrying and medical application.

Apoptosis of Leukemia Cells by Ocimum basilicum Fractions Following TNF alpha Induced Activation of JNK and Caspase 3

Purpose:

Leukemia, one of the major cancers, affects a large proportion of people around the world. Better treatment options for leukemia are required due to a large number of side effects associated with current therapeutic regimens. In the present study, we sought to determine the pathway of triggering apoptosis of leukemic cells by Ocimum basilicum (O. basilicum) plant extract.

Materials/Methods:

Methanolic extract of the O. basilicum plant material was prepared. The crude extract was fractionated into several fractions through column chromatography using ethyl acetate and n-hexane as eluting solvents. Cell viability of leukemic cells was assessed via Cell titer GLO assay and apoptosis was measured through Annexin V/PI staining. Two apoptotic molecules JNK and caspases were analyzed through western blotting while pro-inflammatory cytokines TNFα, CCL2 and CXCL8 using qPCR. Fractions were characterized through LC-MS.

Results:

The most potent with lowest IC50 values among the fractions were BF2 (2:8 n-hexane:ethyl acetate) and BF3 (3:7 n-hexane:ethyl acetate). Cytotoxicity was associated with apoptosis. Apoptosis was found caspasedependent and P-JNK activation was detected sustained. A significant increase in the level of TNF α and a decrease in the level of CXCL8 were observed in BF2 and BF3 treated cells.

Conclusion:

The fractions of O. basilicum extract were found to kill cells following JNK pathway activation. Excellent results were obtained with BF2 and BF3 probably due to predominant Epicatechin and Cinnamic acid derivatives in these fractions.

Biocompatible Polymers and their Potential Biomedical Applications: A Review

Background:

Biocompatible polymers are gaining great interest in the field of biomedical applications. The term biocompatibility refers to the suitability of a polymer to body and body fluids exposure. Biocompatible polymers are both synthetic (man-made) and natural and aid in the close vicinity of a living system or work in intimacy with living cells. These are used to gauge, treat, boost, or substitute any tissue, organ or function of the body. A biocompatible polymer improves body functions without altering its normal functioning and triggering allergies or other side effects. It encompasses advances in tissue culture, tissue scaffolds, implantation, artificial grafts, wound fabrication, controlled drug delivery, bone filler material, etc.

Objectives:

This review provides an insight into the remarkable contribution made by some well-known biopolymers such as polylactic-co-glycolic acid, poly(ε-caprolactone) (PCL), polyLactic Acid, poly(3- hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), Chitosan and Cellulose in the therapeutic measure for many biomedical applications.

Methods: :

Various techniques and methods have made biopolymers more significant in the biomedical fields such as augmentation (replaced petroleum based polymers), film processing, injection modeling, blow molding techniques, controlled / implantable drug delivery devices, biological grafting, nano technology, tissue engineering etc.

Results:

The fore mentioned techniques and other advanced techniques have resulted in improved biocompatibility, nontoxicity, renewability, mild processing conditions, health condition, reduced immunological reactions and minimized side effects that would occur if synthetic polymers are used in a host cell.

Conclusion:

Biopolymers have brought effective and attainable targets in pharmaceutics and therapeutics. There are huge numbers of biopolymers reported in the literature that has been used effectively and extensively.

Functionalized Bacterial Cellulose Microparticles for Drug Delivery in Biomedical Applications

Background:

Bacterial cellulose (BC) has recently attained greater interest in various research fields, including drug delivery for biomedical applications. BC has been studied in the field of drug delivery, such as tablet coating, controlled release systems and prodrug design.

Objective:

In the current work, we tested the feasibility of BC as a drug carrier in microparticulate form for potential pharmaceutical and biomedical applications.

Method :

For this purpose, drug-loaded BC microparticles were prepared by simple grinding and injection moulding method through regeneration. Model drugs, i.e., cloxacillin (CLX) and cefuroxime (CEF) sodium salts were loaded in these microparticles to assess their drug loading and release properties. The prepared microparticles were evaluated in terms of particle shapes, drug loading efficiency, physical state of the loaded drug, drug release behaviour and antibacterial properties.

Results:

The BC microparticles were converted to partially amorphous state after regeneration. Moreover, the loaded drug was transformed into the amorphous state. The results of scanning electron microscopy (SEM) showed that microparticles had almost spherical shape with a size of ca. 350-400 μm. The microparticles treated with higher drug concentration (3%) exhibited higher drug loading. Keeping drug concertation constant, i.e., 1%, the regenerated BC (RBC) microparticles showed higher drug loading (i.e., 37.57±0.22% for CEF and 33.36±3.03% for CLX) as compared to as-synthesized BC (ABC) microparticles (i.e., 9.46±1.30% for CEF and 9.84±1.26% for CLX). All formulations showed immediate drug release, wherein more than 85% drug was released in the initial 30 min. Moreover, such microparticles exhibited good antibacterial activity with larger zones of inhibition for drug loaded RBC microparticles as compared to corresponding ABC microparticles.

Conclusion :

Drug loaded BC microparticles with immediate release behaviour and antibacterial activity were fabricated. Such functionalized microparticles may find potential biomedical and pharmaceutical applications.

Core-Shell Molecularly Imprinted Polymer Nanocomposites for Biomedical and Environmental Applications

Core-shell polymers represent a class of composite particles comprising of minimum two dissimilar constituents, one at the center known as a core which is occupied by the other called shell. Core-shell molecularly imprinting polymers (CSMIPs) are composites prepared via printing a template molecule (analyte) in the coreshell assembly followed by their elimination to provide the everlasting cavities specific to the template molecules. Various other types of CSMIPs with a partial shell, hollow-core and empty-shell are also prepared. Numerous methods have been reported for synthesizing the CSMIPs. CSMIPs composites could develop the ability to identify template molecules, increase the relative adsorption selectivity and offer higher adsorption capacity. Keen features are measured that permits these polymers to be utilized in numerous applications. It has been developed as a modern technique with the probability for an extensive range of uses in selective adsorption, biomedical fields, food processing, environmental applications, in utilizing the plant's extracts for further applications, and sensors. This review covers the approaches of developing the CSMIPs synthetic schemes, and their application with special emphasis on uses in the biomedical field, food care subjects, plant extracts analysis and in environmental studies.

Antiviral potential of green synthesized silver nanoparticles of Lampranthus coccineus and Malephora lutea

Background

Viral and microbial infections constitute one of the most important life-threatening problems. The emergence of new viral and bacterial infectious diseases increases the demand for new therapeutic drugs.

Purpose

The objective of this study was to use the aqueous and hexane extracts of Lampranthus coccineus and Malephora lutea F. Aizoaceae for the synthesis of silver nanoparticles, and to investigate its possible antiviral activity. In addition to the investigation of the phytochemical composition of the crude methanolic extracts of the two plants through UPLC-MS metabolomic profiling, and it was followed by molecular docking in order to explore the chemical compounds that might contribute to the antiviral potential.

Methods

The formation of SNPs was further confirmed using a transmission electron microscope (TEM), UV-Visible spectroscopy and Fourier transform infrared spectroscopy. The antiviral activity of the synthesized nanoparticles was evaluated using MTT assay against HSV-1, HAV-10 virus and Coxsackie B4 virus. Metabolomics profiling was performed using UPLC-MS and molecular docking was performed via Autodock4 and visualization was done using the Discovery studio.

Results

The early signs of SNPs synthesis were detected by a color change from yellow to reddish brown color. The TEM analysis of SNPs showed spherical nanoparticles with mean size ranges between 10.12 nm to 27.89 nm, and 8.91 nm 14.48 nm for Lampranthus coccineus and Malephora lutea aqueous and hexane extracts respectively. The UV-Visible spectrophotometric analysis showed an absorption peak at λmax of 417 nm.The green synthesized SNPs of L. coccineus and M. lutea showed remarkable antiviral activity against HSV-1, HAV-10, and CoxB4 virus. Metabolomics profiling of the methanolic extract of L. coccineus and M. lutea resulted in identifying 12 compounds. The docking study predicted the patterns of interactions between the compounds of L. coccineus and M. lutea with herpes simplex thymidine kinase, hepatitis A 3c proteinase, and Coxsackievirus B4 3c protease, which was similar to those of the co-crystal inhibitors and this can provide a supposed explanation for the antiviral activity of the aqueous and nano extracts of L. coccineus and M. lutea.

Conclusion

These results highlight that SNPs of L. coccineus and M. lutea could have antiviral activity against HSV-1, HAV-10, and CoxB4 virus.

Copper(II) oxide nanoparticles coated cellulose sponge-an effective heterogeneous catalyst for the reduction of toxic organic dyes

Discharge of unprocessed coloured waste water from industries gives rise to water contamination. In the current work, we propose the application of CuO nanoparticles supported on cellulose kitchen wipe sponge as a heterogeneous catalyst for the reductive decolourization of various toxic cationic and anionic dye molecules. The catalytic activity of the CuO nanoparticles under normal light for reduction has been examined in which sunlight irradiation is not necessitated. The CuO nanoparticles were synthesized by a simple wet chemical method and characterized using High Resolution Transmission Electron Microscope (HRTEM), SEM, EDX, XRD, XPS and TGA analyses. In the presence of CuO@CS catalyst and sodium borohydride, decolourization reaction of dyes such as acid red, acid green, methylene blue, rhodamine B and solochrome black-T was carried out. The catalytic reduction behaves as a pseudo-first-order reaction and is found to be superior in comparison with other reported catalysts in terms of reaction velocity. The reduction reaction can be further accelerated by increasing the reaction temperature. The developed catalyst drives the reduction faster on exposing the reaction mixture to sunlight confirming the usage of the catalyst at normal light and sunlight conditions. The catalyst retains 100% efficiency even after 5 cycles and remains suitable even for further use. Thus, a low-cost heterogeneous catalyst has been successfully developed and employed to decolourize various dye molecules in short duration with good recyclability and therefore can be used as the potential candidate in environmental remediation.