Enhancing the efficiency of zero valent iron by electrolysis: Performance and reaction mechanism

Promoted iron corrosion and enhanced phosphate removal by micro-electric field driven zero-valent iron

Zero-valent iron (Fe0) is restricted in phosphate removal due to the formation of a passive P-Fe layer on its surface. A micro-electric field (0.20 mA cm-2) was employed in Fe0 column to facilitate iron corrosion for enhanced phosphate removal with a Fe0 column as the control. The performance of two columns was compared by batch experiment at a Fe0 filling rate of 10 vol% with quartz sand as dispersing media. The stability and reusability of micro-electric field driven Fe0 (MFD-Fe0) column was estimated by cyclic test. Solid phase analysis showed promoted iron corrosion, iron ion generation, and secondary mineral production such as lepidocrocite and magnetite in the MFD-Fe0 column. Since iron ions tended to precipitate with phosphate, and iron minerals provided reaction sites for phosphate adsorption, the MFD-Fe0 column achieved an enhanced phosphate removal of 94.1%, 2.8 times higher than that of the Fe0 column. The increase of current density from 0 to 0.20 mA cm-2 significantly improved phosphate removal from 24.5% to 94.1%, further demonstrating the promoting effect of micro-electric field on iron corrosion. The MFD-Fe0 column also possessed excellent stability and reusability. It only showed a slight decrease of phosphate removal from 94.1% to 89.7% in eight cycles. It restored a phosphate removal capacity of 97.4% as compared to the initial MFD-Fe0 column by eluting iron (hydro)oxides on Fe0 and quartz sand surfaces with sulfuric acid. This study indicated that MFD-Fe0 is a promising method to remove phosphate from water and an alternative strategy for overcoming Fe0 passivation.

Which is Better for Nanomedicines: Nanocatalysts or Single-Atom Catalysts?

With the rapid advancements in nanotechnology and materials science, numerous nanomaterials have been used as catalysts for nanomedical applications. Their design and modification according to the microenvironment of diseases have been shown to achieve effective treatment. Chemists are in pursuit of nanocatalysts that are more efficient, controllable, and less toxic by developing innovative synthetic technologies and improving existing ones. Recently, single-atom catalysts (SACs) with excellent catalytic activity and high selectivity have attracted increasing attention because of their accurate design as nanomaterials at the atomic level, thereby highlighting their potential for nanomedical applications. In this review, the recent advances in nanocatalysts and SACs are briefly summarized according to their synthesis, characterizations, catalytic mechanisms, and nanomedical applications. The opportunities and future scope for their development and the issues and challenges for their application as nanomedicine are also discussed. As far as it is known, the review is the systematic comparison of nanocatalysts and SACs, especially in the field of nanomedicine, which has promoted the development of nanocatalytic medicine.

An efficient Egeria najas-derived biochar supported nZVI composite for Cr(VI) removal: Characterization and mechanism investigation based on visual MINTEQ model

Egeria najas is a submerged aquatic plant, and the literatures on resourcification of submerged aquatic plant biochar remain limited. Until now, there has been no study on submerged aquatic plant biochar supported nZVI that is widely applied for removal of diversified contaminants in solution. In this study, an efficient approach to the preparation of Egeria najas-derived biochar supported nZVI composite is first developed for Cr(VI) removal in wastewater. The adsorption behavior and mechanism of Cr(VI) removal on the as-prepared Egeria najas-derived biochar/nZVI (EN@nZVI) composite were investigated. The results of FTIR and XPS indicate that the EN@nZVI surface had many functional groups such as R-COOH, R-OH, R-NH₂ and R-C-O-C, etc, which could provide active sites during the adsorption process. The BET results showed that the EN@nZVI had large specific surface area and average pore, which were 142.49 m²/g and 9.85 nm, respectively. EN@nZVI demonstrated high reactivity for Cr(VI) removal. Compared with nZVI, Cr(VI) removal efficiency by EN@nZVI is 50% higher than that of nZVI within 0.5 h. Furthermore, the maximum adsorption capacity of Cr (VI) was 56.79 mg/g and the energy of activation (E_a) was 31.30 kJ/mol. The adsorption process was well described by the pseudo-second order model and Sips adsorption isotherm model. The reaction mechanism of Cr(VI) removal was a multi-step removal mechanism, involving adsorption, surface complex formation, reduction and ion exchange reaction.

Mechanisms of electro-assisted persulfate/nano-Fe0 oxidation process: Roles of redox mediation by dissolved Fe

Mechanisms involved in an electrochemically assisted oxidation process using persulfate and nanosized zero-valent iron (NZVI) were elucidated. Initially, Fe⁰ acted as a source of Fe²⁺ to activate the persulfate, then Fe²⁺/Fe³⁺ redox mediation between cathode and persulfate played a decisive role in persulfate activation at a current density low enough not to inhibit Fe⁰ corrosion. An excessive current density which resulted in a low cathodic potential limited Fe⁰ corrosion and therefore limited the supply of dissolved Fe to activate the persulfate. Direct oxidation of phenol at the anode therefore became more important under the excessive current density than oxidation by sulfate radicals. At a low current density, Fe⁰ in the NZVI particles was completely transformed into iron (oxyhydr)oxides such as ferrihydrite, lepidocrocite, and magnetite. Fe⁰ was transformed into Fe²⁺ little when the current density was high. Increasing the current density increased the energy cost by increasing the amount of electrical energy dissipated in side reactions that decreased sulfate radical formation. The results indicated that a low current density can generally be used to give a high reaction rate and a high energy efficiency and that a high current density can be used when the NZVI particles need to be preserved.

Effect of Co addition on catalytic activity of FePCCu amorphous alloy for methylene blue degradation

A novel FeCoPCCu amorphous alloy as a highly efficient catalyst in Fenton-like reactions for methylene blue degradation.